Eldes ZEUS User manual

Eldes ZEUS User manual
GSM pager for vehicles
ZEUS v1
User manual v1.0
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its
documentation indi- cates that in the EU the product must not be disposed of together with
household waste.
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and
peoplearound. Pager for vehicles ZEUS (further referenced as the system) contains an integrated
radio transceiver operating in GSM900 and GSM1800 bands.
•
•
•
•
Don’t
Don’t
Don’t
Don’t
use the system where it can interfere with other devices and cause any potential danger.
use the system in hazardous environment.
expose the system to high humidity, chemical environment or mechanical impacts
attempt to personally repair the system
Any system repairs must be done only by qualifi ed, safety aware personnel.
Mains power must be disconnected before any installation or tuning work starts. The
system installation or mainte- nance must not be done during stormy conditions.
The system must be used only with approved back-up battery to avoid fire or explosion
hazards. Special care must be taken connecting positive and negative battery terminals.
The device is powered by a backup battery. The device is switched off by unplugging main
power supply connector and disconnecting battery connector.
Fuse F1 type - C1S 2.5A. Blown fuse cannot be replaced by the user and the replacement
fuses have to be exactly the same as indicated by the manufacturer.
WARNING: in order to avoid fire or explosion hazards the system must be used only with
approved back-up battery. Special care must be taken when connecting positive and negative
battery terminals
Limited Liability
The buyer must agree that the system will reduce the risk of theft, burglary or other dangers but
does not guarantee against such events.
“ELDES UAB” will not take any responsibility regarding personal, property or revenue loss while
using the system.
“ELDES UAB” responsibility according to local laws does not exceed value of the purchased system.
2
“ELDES UAB” is not affiliated with GSM operators providing cellular services therefore is not
responsible for the quality of cellular services.
Manufacturer Warranty
The system carries a 24-month warranty by the manufacturer “ELDES UAB”.
Warranty period starts from the day the system has been purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines listed in the
manual and within specified operating conditions. Receipt with purchase date must be kept as a
proof.
The warranty is voided if the system has been exposed to mechanical impacts, chemicals, high
humidity, fluids, corrosive and hazardous environment or other force majeure factors.
Copyright © “ELDES UAB”, 2009. All rights reserved
It is not allowed to copy and distribute information in this document or pass to a third party
without advanced written authorization by “ELDES UAB” “ELSDES UAB” reserves the right to
update or modify this document and/or related products without a warning.
Hereby, ELDES UAB declares that this GSM System ZEUS is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity
may be consulted at www.eldes.lt/ce
Package Content:
1.
2.
3.
4.
5.
System ZEUS ......................................... 1pcs
Microphone............................................. 1pcs
ZEUS users manual.................................. 1pcs
Main connector with fuse holder.................. 1pcs
Back-up battery........................................ 1pcs
About User Manual
This document describes system ZEUS installation and operation. It is very important to read User
Manual before start using the system.
A quick start guide is located in first two chapters. Chapter 3 and 4 describe additional system
capabilities.
3
CONTENT
1. General Information
1.1 Function......................................................................................................
1.2 Operation Description....................................................................................
1.3 Technical Specifications ................................................................................
1.4 Connector Functionality.................................................................................
1.5 Connection Circuit.........................................................................................
1.6 System Installation.......................................................................................
5
5
6
6
7
8
2. System Pre-operation and the Main Control Commands
2.1 Verification of SMS Central Number.................................................................
2.2 Password Change.........................................................................................
2.3 User Numbers...............................................................................................
2.3.1 Saving or Changing Numbers ......................................................................
2.3.2 Verification of Saved Numbers......................................................................
2.3.3 Deletion of Saved Numbers. .......................................................................
9
10
10
10
10
11
3. Additional System Capabilities
3.1 Security zones and Configuring input impulse duration.........................
3.1.1 Zone settings. STATUS.....................................................
3.1.2 Renaming Zones.............................................................
3.1.3 Enabling/Disabling Zones..................................................
3.1.4 Configuring input impulse duration.....................................
3.1.5 Delay Time Configuration of the System in Secure Mode…….
3.2 Info on Status SMS...........................................................................
3.3 Remote Microphone Listening.............................................................
3.4 Blocking Unknown Numbers...............................................................
3.5 Notification about Discharged Vehicle Battery.......................................
11
11
11
12
12
12
13
13
13
14
4. Appendix
4.1 Restoring default parameters.............................................................
4.2 Replacing back-up battery..................................................................
4.3 Technical support..............................................................................
4.4 Shortlist of essential functions............................................................
14
14
14
15
4
1. General Information
1.1 Function
The system ZEUS is a micro-processor device used to remotely observe and control cars,
motorbikes and other vehicles through GSM network.
Examples of system usage:
Informing the user by an SMS message or phone call about the engagement of the car
security system. Your security system detectors will always be adjusted correctly and
your car will never disturb you or your neighbours unnecessarily.
Vehicle search services through www.locator.lt
Informing the user about low battery.
Listening to what is going on inside the car through a remote microphone
A possibility to check over the mobile phone if you have not forgotten turning on the
security system.
1.2 Operation Description
Informational system ZEUS works over GSM network. It is not an alarm system- it is an
accessory to one. However, the device can be used independently, without any security system.
This is described in section 1.5.
If vehicle siren, shock sensor, capacity sensor or any other sensor (depending on the
installation) is triggered, ZEUS systems sends SMS message and calls the pre-programmed
numbers until the call is answered or one of the two users presses rejection key or the call is
terminated by mobile network operator. If you answer the call, the microphone will activate and
you will be able to listen to what is happening inside the vehicle. After hanging up the phone the
system gets back to the previous status. SMS message with the name of the triggered input (zone)
is sent until first successful message delivery to one of the users.
If the system drops the call immediately after calling to the number of ZEUS system,
vehicle alarm system is turned off. In such a case you can check if you did not forget to turn
vehicle alarm system. If the security system is turned on, after four or five call signals ZEUS will
answer the call activating the microphone. You will be able to listen to what is happening inside the
vehicle.
When vehicle battery is low, the system will send SMS message informing that the
battery is getting low. This message is sent when vehicle battery voltage is 11 volts for 40 seconds
and longer.
If an unknown number tries calling the system or if the system receives SMS message
iwith a wrong password, the system ignores this.
To find out the place of your vehicle you have to order the service in the website
www.locator.lt prior inserting SIM card in system port.
If, during the theft, vehicle battery is disconnected from the car, the system ZEUS is
powered by a backup battery and the user receives SMS message notifying about this. A fully
charged 0.6Ah backup battery keeps the system operating for up to 10 hours.
USEFUL INFORMATION
To increase system reliability, it is recommended not to use prepaid SIM cards. The system would fail to
send any messages upon depletion of prepaid account. Also it is recommended to disable call forwarding
and voice mail.
5
USEFUL INFORMATION
It is worth to choose the same GSM cellular provider as most users use assuring fast and reliable SMS
message delivery and phone call connection.
1.3 Technical Specifications
Electrical and mechanical specifications
Supply voltage
Current during call
Current used in standby mode
GSM modem frequency
Number of “high” level (positive) inputs
Number of “low” level (negative)
Arming with “low” level (negative)
Arming with “high” level (positive)
Dimensions
Operating temperature range
10-24V DC
not more than 250mA
not more than 40mA
900/1800Mhz
1
2
1 input
1 input
114x78x32mm
-20…+55oC (-30...+55oC
with limitations)
Lead acid, 8V, 0.4-1.3Ah;
3A
Back-up Battery type
Main fuse
1.4 Connector Functionality
Fig. No1
SIM CARD
D1
D2
ANT
GSM MODEM
DEFAULT
Short explanation
GSM MODEM
SIM CARD
LED
DEFAULT
MIC
ANT
8 pin connector
AKU
AKU
LED
MIC
8 PIN CONNECTOR
1 2 3 4 5 6 7 8
.
of the main units
GSM network 900/1800MHz modem
SIM card
Light-emitting diodes indicator
Connectors (D1 and D2) for restoring default settings
Microphone input
GSM antenna
Main 8pin connector
Back-up battery connector
6
Main connector pin-out
No.
1
2
3
4
5
6
7
8
Labeling
n.c.
Z3
Z2
Z1
ON2
ON1
GND
+12V
Explanation
Not connected
“low” level input Z3
“low” level input Z2
“low” level input Z1
Arming with “high” level (positive)
Arming with “low” level (negative)
negative supply (earth) pin
Positive power supply input (+12..24V)
Wire color
Brown
Blue
Orange
Yellow
Green
Black
Red
1.5 Connection Circuit
Fig. No2.
GSM pager ZEUS
Microphone
Z1
ON2
ON1
3
4
5
6
GND +12V
3A
Back-up
battery AKU
8V
8
red
green
7
black
orange
yellow
Z2
2
blue
Z3
brown
1
GNDVehicle
Shock sensor
battery AKU
12V
Negative
door‟s switch
Negative Bonnet
switch
Negative
output
To Siren positive
output
Negative
output
When armed
“high” level
(positive)
J2*
J1*
When armed
“low” level
(negative)
+12V
Equivalent vehicle alarm system circuit
7
ON1 and ON2 inputs are equivalent; they only differ in input levels. It is sufficient connecting only
one of them. Most often they are connected to system output that is connected to the relay
blocking a particular circuit in car installation when the alarm is armed. If the system ZEUS is
installed independent from security system or if there is no alarm system in the vehicle, connect
ON1 to the hidden switch J1, the other pin of which is connected to the vehicle body (ground).
Also, you can connect ON2 to the hidden switch J2, the other pin of which is connected to +12V.
“Low” level (negative) input Z2 and Z3 are most often connected to the doors, bonnet switch or
shock, microwave or ultrasound sensor output which, when triggered, produce low level.
“High” level (positive) input Z1 is most often connected to siren wire, if the latter is commuted via
plus, or to the ignition connector.
1.6 System Installation
Main vehicle battery must be disconnected before any installation or tuning work starts.
Do not install the system to spinning or moving parts of the vehicle. The device and its
backup battery can be installed only inside the vehicle to the units that do not heat up or
heat up very gently. When wiring the leads from the vehicle engine compartment to the
interior use rubber insulators. Twist the wires and swirl them using insulating tape.
1.
2.
Remove device cover and insert SIM card in the slot. SIM card pin request has to be
deactivated prior inserting it in the device (PIN code request can be turned off inserting
SIM card in a mobile phone and choosing the appropriate command). The card must be
clean of old SMS messages.
Connect the circuit according to Fig. No2. 4 wires are sufficient for a minimal installation:
1) +12V;
2) GND
3) Alarm system siren wire can be connected to any of the zones Z1-Z3, depending on
whether security system commutates “high” or “low” level to the siren.
4) The commutated output of the installed alarm system (most often it is used to
connect starter/ignition blocking relay) is connected to security arming wire ON2 or ON1,
depending on whether the alarm system commutates “high” or “low” level.
If the vehicle does not have security system installed, or if you want to use ZEUS as an
additional system operating independently, connect any of the hidden switches J1 or J2 to
ON1/ON2.
3.
4.
5.
6.
Insert microphone pin in the slot. Please note the the position of the connector key. The
key must be on top.
Place device cover and screw its bolts.
Connect backup battery and vehicle battery.
The system has to start in less than a minute. LED indicator should blink every five
seconds informing about the connection to GSM network. If the indicator is blinking very
frequently, i. e., several times per second, it is possible that SIM card is inserted
incorrectly or PIN code request is not turned off.
8
2. System pre-operation and essential control commands
VERY IMPORTANT!!!
Underscore symbol „_‟ in this manual is used to represent space. When writing SMS messages, every
underscore symbol should be replaced by single space symbol. XXXX – means password. Don‟t
leave any space at the beginning and the end of the message.
2.1 Checking SMS central number
SMS central number can be checked as long as factory default password is not changed.
SMS central number is stored in SIM card, therefore if ZEUS SIM card was previously
used in a mobile phone and SMS messages were successfully sent out / received, SMS
central number does not need to be changed. Usually SMS central number of the SIM
card is already entered by the operator.
Call the system ZEUS from your mobile phone and wait until the system rejects the call. In
approximately 30-60 seconds you will receive an SMS message: Please change the default
password.
If you received this message, go to step 2.2. If you did not receive the message, change SMS
central number.
Instead of calling the system you can send an SMS message to the system ZEUS with the following
text:
TEST
If the telephone account is topped up and SMS central number is correct, you should soon receive
a message: SMS central number is correct.
If you received this message, go to step 2.3. If you did not receive the message, change SMS
central number.
New central number can be entered by sending the following SMS message:
XXXX_SMS_+370111111111
XXXX is a password. The default password is four zeros: 0000.
Ones should be replaced with SMS central number of the provider, whose SIM card is inserted in
the system. If you do not know SMS central number, you can get it from the mobile network
provider.
E. g. 0000_ SMS_+37069899992
Message should be sent to the number of SIM card which is placed into the system. If all went
correct, the system will reply with the following message:
SMS central number has been successfully changed to +37011111111
9
2.2 Administrator Password Change
All SMS commands start with a password, please memorize it. Manufacturer default password is
four zeros 0000, which is necessary to change!
Manufacturer default password can be changed by sending the following SMS message to ZEUS
system:
0000_PSW_XXXX
To replace your password send the following SMS message:
YYYY_PSW_XXXX
XXXX is any four digit number except four zeros.
Non-numerical characters like dots, colons, spaces are not allowed. YYYY is the old system
password.
If you forgot the password, default manufacturer password can be restored, see chapter 4.1 for
more details.
2.3 Administrator Numbers
The system ZEUS allows to preprogram up to five different mobile numbers which will have access
to and control the system. NR1 is mandatory while others can be skipped. All numbers must be
entered starting with international country code, e. g. national code for Lithuania is 370, UK44. The plus sign is not necessary. Numbers without the international code are not allowed.
2.3.1 Saving or Changing Administrator Numbers
Send SMS message with the following text:
XXXX_NR1:37011111111_NR2:37011111111
Ones should be replaced with administrator numbers.
Numbers don’t have to be entered in sequential order right away. E. g. use can enter first number
by sending the following SMS message:
XXXX_NR1:37011111111
Numbers can be changed same way as described above. New number will overwrite old one,
therefore no erasing is necessary.
2.3.2 Verification of Administrator Numbers
To inquire the system about pre-programmed administrator numbers send the following SMS
message:
XXXX_HELPNR
The system will reply with all pre-programmed numbers.
10
2.3.3 Deletion of Administrator Numbers
To erase a second administrator number send an SMS message:
XXXX_NR2:DEL
The system will not allow erasing first number NR1. It can only be modified.
E. g. XXXX_NR2:DEL
3. Additional system capabilities
3.1 Security zones and Configuring input impulse duration
3.1.1 Zone settings. STATUS
To find out current input names and their settings send the following SMS message:
XXXX_STATUS
You will receive the answer:
e. g.: System armed/disarmed Z1:siren:ON/OFF T1:600 Z2:doors:ON/OFF T2:600
Z3:sensor:ON/OFF T3:600
ON- means that appropriate zone is activated, i. e., it will react in the case of alarm. OFF- it is
deactivated.
T1, T2 and T3 is delay of a particular one in milliseconds, i. e., a period until the input starts
reacting to signal change.
E. g., in this case alarm will be triggered only if the voltage (signal) is transmitted to any of the
inputs for at least 600ms.
3.1.2 Renaming Zones
Manufacturer initially set the following zone and controlled output names: Z1- siren, Z2-doors, Z3sensor.
The user is free to change any of these names. The names cannot repeat or be identical to control
commands.
Zone names can be changed by sending the following SMS message:
XXXX_Z1:NewZoneName_Z2:NewZoneName_Z3:NewZoneName
The user can change all names at once, several names or only one name. Maximum input name
length is 8 characters.
E.g. XXXX_Z2:BONNET
11
3.1.3 Enabling/disabling zones
USEFUL INFORMATION
The zones can be enabled/disabled together or separately one by one.
NOTE
Manufacturer set all the zones activated, i. e. in mode ON.
Enabling Zone
Any zone can be enabled by sending the following SMS message:
XXXX_Z1:ON_Z2:ON_Z3:ON
e.g. XXXX_Z2:ON;
Disabling Zone
Any zone can be disabled by sending the following SMS message:
XXXX_Z1:OFF_Z2:OFF_Z3:OFF
e.g. XXXX_Z2:OFF;
3.1.4 Zone Impulse Duration Configuration
The user can change impulse duration for every input (zone) IN1-IN3. The zone is triggered only if
the impulse transmitted to the input is longer than the pre-set value. Factory default duration is
600ms.
This setting can be changed for every input or for all imputs at once by sending the following SMS
message:
XXXX_T1:TT_T2:TT_T3:TT
where TT means input reaction time in milliseconds. Possible TT values are 100-30000. Measuring
is every 100.
E. g., XXXX_T3:1500 means that input IN3 will react only in the case if the impulse transmitted
to it is not shorter than 1.5 seconds.
3.1.5 Delay Time Configuration of the System in Secure Mode
For the system ZEUS the manufacturer set 5 sec. delay time after arming security system. During
this period the system does not react to triggered zones.
If ZEUS is used as an independent security system, the user has enough time to leave the vehicle
after turning on the hidden switch.
12
This time setting is changed by sending the following SMS message:
XXXX_TSEC:TT
where TT means the delay in milliseconds after turning on secure mode. Possible TT values are
100-30000. Measuring is every 100.
E. g., XXXX_TSEC:20000 means that after arming security system it will not react to any
triggered sensor for 20 seconds.
3.2 Info on Status SMS
System ZEUS can be inquired at any time about its status, signal strength. At the same time
system can be tested. If SMS response message is received, means system is functioning properly.
This is also useful for users with prepaid SIM cards. It can be checked whether SIM card has
enough remaining balance for sending SMS. Send SMS message:
XXXX_INFO
3.3 Remote Microphone listening
To be able to listen what is going on in vehicle can be done in 3 different ways:
1.
When alarm has been activated, the system will ring pre-programmed numbers and user
can answer the call. Remote microphone will be enabled for listening. Ring the system. If
vehicle alarm system is armed, the system ZEUS will answer the call after 4-5 ring
signals turning on the microphone.
2.
By sending SMS message:
XXXX_MIC
The system will ring the sender of former SMS, and upon answering the call, user can listen to any
sounds in the building. The phone call must be answered within 20 seconds otherwise the system
will stop trying and return to previous state.
3.4 Blocking unknown incoming numbers
By default ESIM262 can be controlled from any of the pre-programmed numbers NR1and NR5. But
user can access the system and control parameters from any number as long as password is know.
To enable this feature, send SMS message:
XXXX_STR:ON
E. g. 0000_STR:ON
To disable this feature, send SMS message:
XXXX_STR:OFF
13
3.5 Notification about Discharged Vehicle Battery
When vehicle battery is low, the system sends SMS message notifying that the battery of the
vehicle is running low. This message is delivered when ius baigia išsikrauti. This message is
delivered when vehicle battery voltage is 11 volts for 40 seconds and longer.
To disable this feature, send SMS message:
XXXX_M:OFF
To re-enable this feature, send SMS message:
XXXX_M:ON
4. Appendix
4.1 Restoring Default Parameters
To restore default parameters:
• disconnect both power supplies: main and back-up battery.
• short circuit (connect) connectors D1 and D2
• connect power supply for several seconds
• disconnect power supply
• disconnect connectors D1 and D2
4.2 Replacing back-up battery
Backup battery has limited number of charging-discharging cycles. In time the battery loses its
capacity. Therefore in the case of theft when the main power supply of the vehicle is disconnected
the system ZEUS will operate for a shorter period.
We recommend replacing the backup battery of the system ZEUS at least every 3 years. The
replacement is done by disconnecting battery connector AKU and connecting the new battery.
4.3 Technical support
Indication
LED indicator is off or not blinking
Indicator blinking several times per
second
System does not send any SMS
messages
Possible reason
· no external power supply
· circuit not properly connected
· blown fuse
· no network signal
· SIM card is not inserted
· PIN code hasn’t been disabled
· SIM card not active
· SIM card account depleted
· incorrect SIM central number
14
·
·
·
·
·
·
Received SMS message “Incorrect
Format”
No sound
No sound while listening to remote
microphone
no network signal
user number is not programmed in user list
incorrect syntax
extra space symbol left in SMS message
neprijungtas mikrofonas
neteisingai prijungtas mikrofonas
· micropone not connected
· Microphone connection incorrect
If your problem could not be fixed by the self-guide above, please contact your distributor or
ELDES tech support by email [email protected]
More up to date information about your device and other products can be found at the
manufacturer's website www.eldes.lt
4.4 Shortlist of essential functions
To find out if you turned on
vehicle security system
Call the system ZEUS. If the call was rejected
immediately or after one ring signal, the system is
disarmed.
If the call carries on and you hear more than one ring
signal, the system is armed.
To find out system status
Send SMS message:
XXXX_INFO
To find out programmed user
numbers
Send SMS message:
XXXX_HELPNR
To find out zone names ant
settings
Send SMS message:
XXXX_STATUS
15
Made in Lithuania.
www.eldes.lt
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement