Yard Machines 730 thru 738 Owner`s manual

Yard Machines 730 thru 738 Owner`s manual
OWNER’S MANUAL
OWNER’S MANUAL
Welcome To Ultimate Relaxation!
Please read the entire Owner’s Manual before installing and using your spa. The goal of this
manual is to provide you with safety and operational information plus some tips that will help
you enjoy your spa to its fullest.
At the time of print, this manual is accurate in its information. The manufacturer reserves the
right to change or improve its product without prior notice.
Record Of Ownership
Name��������������������������������������������������������������������������������
Address������������������������������������������������������������������������������
City _____________________________________ State __________ Zip�������������������������
Date Purchased ______ /______ /_______
Model ______________________________ Serial #������������������������������������������
Dealer Name�������������������������������������������������������������������������
Phone # (______)________-__________
Service Tech Rep����������������������������������������������������������������������
*Serial Number Location
The serial number for your spa is located in the filter area, on the spa system pack, or on the listing
plate on the skirting. Ex. 1300420
DO NOT DIVE.
1
TABLE OF CONTENTS
Safety Instructions��������������������������������������������������������������������������������������������������������������������� 3-10
Glossary of Spa Terminology��������������������������������������������������������������������������������������������������������� 11
Electrical Installation Requirements������������������������������������������������������������������������������������������ 12-13
Wiring Schematic������������������������������������������������������������������������������������������������������������������ 14
Site Preparation / General Guidelines������������������������������������������������������������������������������������ 15
Installation Instructions���������������������������������������������������������������������������������������������������������� 16
Water Chemistry Terms You Should Know�������������������������������������������������������������������������������� 17-18
Eco Pur Filtration�������������������������������������������������������������������������������������������������������������������������� 19
Water Quality Maintenance – Start-Up������������������������������������������������������������������������������������������� 20
Water Quality Maintenance Schedule���������������������������������������������������������������������������������������� 21-22
Spa Water Maintenance Trouble-Shooting Guide��������������������������������������������������������������������������� 23
Why Chemicals are Important in a Spa������������������������������������������������������������������������������������������� 24
Maintenance Recommendations���������������������������������������������������������������������������������������������������� 25
Winterizing Your Spa��������������������������������������������������������������������������������������������������������������������� 26
Spa Specifications������������������������������������������������������������������������������������������������������������������������� 27
Spa Controls (CLS 360 and CLS 415)����������������������������������������������������������������������������������������� 28-29
Spa Diagnostics Messages (CLS 360 and CLS 415)����������������������������������������������������������� 30-31
Spa Controls (CLS 524, CLS 730, CLS 730L, CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055)
Main Menus������������������������������������������������������������������������������������������������������������������������� 32
Fill It Up�������������������������������������������������������������������������������������������������������������������������������� 33
Spa Behavior������������������������������������������������������������������������������������������������������������������������� 34
Temperature & Temp Range������������������������������������������������������������������������������������������������� 35
Mode – Ready and Rest�������������������������������������������������������������������������������������������������������� 36
Flip (Invert Display)���������������������������������������������������������������������������������������������������������������� 37
Adjusting Filtration���������������������������������������������������������������������������������������������������������������� 37
General Messages����������������������������������������������������������������������������������������������������������������� 38
Heater-Related Messages������������������������������������������������������������������������������������������������������ 39
Sensor-Related Messages������������������������������������������������������������������������������������������������������ 40
System-Related Messages������������������������������������������������������������������������������������������������������ 41
Standard Fusion Audio System������������������������������������������������������������������������������������������������������ 42
Deluxe Fusion Audio System����������������������������������������������������������������������������������������������������� 43-44
Spa Trouble-Shooting Guide����������������������������������������������������������������������������������������������������� 45-46
Regular Maintenance Procedures���������������������������������������������������������������������������������������������� 47-48
Spa Care and Maintenance Record������������������������������������������������������������������������������������������� 49-52
DO NOT DIVE.
2
SAFETY INSTRUCTIONS
Save These Instructions
Included with your new spa is a safety sign. The sign is for you and your guest’s protection
and is suitable for outdoor use in wet locations. The sign should be placed in a location visible
to all users of the spa.
Please take time to point out the physical location of the safety sign and the importance
of the safety precautions displayed on the safety sign to all of your guests. Remember, your
safety and the safety of anyone who enjoys the use of your spa is our utmost concern.
The sign should be mounted with screws or another type of permanent fastener. Additional
or replacement signs can be obtained from your dealer or direct from the factory.
Introduction
It’s time to relax! You now have your very own portable spa. By fully understanding the operation of each of the features of your new spa, you will be assured of many years of hassle-free, hot
water therapy and fun.
Your safety is of paramount importance. We urge you to read and become thoroughly familiar
with all safety aspects addressed in this manual.
Through reading and totally understanding the important information in your owner’s manual,
you will realize that you now own THE ULTIMATE RELAXATION MACHINE!
DO NOT DIVE.
3
SAFETY INSTRUCTIONS
Important Safety Instructions
When installing and using this electrical equipment, basic safety precautions should
be observed including the following:
Read And Follow ALL
INSTRUCTIONS
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire conductor is provided on this unit to connect a minimum 6 AWG
(13.302mm2) solid copper conductor between this unit and any metal equipment,
metal enclosures of electrical equipment, metal water pipe, or conduit within 5 feet
(1.5m) of the unit
(For cord-connected/convertible units)
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
(For units intended for indoor use only)
WARNING – For indoor use only. This unit is not intended for outdoor use.
(For units intended for outdoor use only)
WARNING – For outdoor use only. This unit is not intended for indoor use.
DO NOT DIVE.
4
SAFETY INSTRUCTIONS
Important Safety
Instructions (cont.)
(For units with GFCI)
WARNING – This product is provided with a ground-fault circuit interrupter
located on the front panel of selected swim spas and on the power cord of
120 volt convertible spas. The GFCI must be tested before each use. With the
product operating, open the service door. When the product stops operating,
this merely indicates that the door is equipped with an electrical interlock.
Next, push the test button on the GFCI and close the service door. The product should not operate. Now open the service door, push the reset button
on the GFCI and close the service door. The product should now operate
normally. When the product fails to operate in this manner, there is a ground
current flowing indicating the possibility of an electric shock. Disconnect the
power until the fault has been identified and corrected.
ANGER – Risk of Accidental Drowning. Extreme caution must be exercised to preD
vent unauthorized access by children. To avoid accidents, ensure that children cannot use this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the specific water flow created by the pump. Should the need arise to replace the suction
fittings or the pump, be sure that the flow rates are compatible.
Never operate spa if the suction fittings are broken or missing. Never replace a suction
fitting with one rated less than the flow rate marked on the original suction fitting.
DANGER – Risk of Electric Shock. Install at least 5 feet (1.5m) from all metal surfaces.
As an alternative, a spa may be installed within 5 feet of metal surfaces if each metal
surface is permanently connected by a minimum 8AWG (8.4mm2) solid copper conductor to the wire connector on the terminal box that is provided for this purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a
light, telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) T he water in a spa should never exceed 40˚C (104˚F). Water temperatures
between 38˚C (100˚F) and 40˚C are considered safe for a healthy adult.
Lower water temperatures are recommended for young children and when
spa use exceeds 10 minutes.
DO NOT DIVE.
5
SAFETY INSTRUCTIONS
Important Safety
Instructions (cont.)
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 38˚C (100˚F).
c) B
efore entering a spa, the user should measure the water temperature
since the tolerance of water temperature- regulating devices varies.
d) T he use of alcohol, drugs, or medication before or during spa use may lead
to unconsciousness with the possibility of drowning.
e) O
bese persons and persons with a history of heart disease, low or high
blood pressure, circulatory system problems, or diabetes should consult a
physician before using a spa.
f) P ersons using medication should consult a physician before using a spa
since some medication may induce drowsiness while other medication may
affect heart rate, blood pressure, and circulation.
(For spas with a gas heater)
WARNING – Risk of Suffocation. This spa is equipped with a gas heater and
is intended for outdoor use only unless proper ventilation can be provided for
an indoor installation.
HYPERTHERMIA
Hyperthermia occurs when the internal temperature of the body reaches a
level several degrees above the normal body temperature of 98.6° F.
THE SYMPTOMS OF HYPERTHERMIA INCLUDE:
• Dizziness • Fainting • Drowsiness • Lethargy
• Increase in Internal Body Temperature
THE EFFECTS OF HYPERTHERMIA INCLUDE:
nawareness of Impending Hazard • Failure to Perceive Heat • Failure to
U
Recognize the Need to Exit Spa • Physical Inability to Exit Spa • Fetal Damage
in Pregnant Women • Unconsciousness Resulting in a Danger of Drowning
DO NOT DIVE.
6
SAFETY INSTRUCTIONS
Important Safety
Instructions (cont.)
DANGER – To reduce the risk of injury to persons, do not remove the suction grate.
Suction through drains and skimmers is powerful when the jets in the spa are in
use. Damaged covers can be hazardous to small children and adults with long hair.
Should any part of the body be drawn into these fittings, turn off the spa immediately. As a precaution, long hair should not be allowed to float in the spa.
WARNING – Install the spa so that water can be easily drained out of the compartment containing electrical components so as not to damage equipment. When
installing the spa make sure to allow for an adequate drainage system to deal with
any overflow water. Please allow for at least 2 feet of clearance around the perimeter of the spa to provide enough room to access for servicing. Contact your local
dealer for their specific requirements.
WARNING – The spa should be covered with an approved locking cover when not
in use, to prevent unauthorized entry and injuries.
WARNING – People with infections, sores or the like should not use the spa. Warm
and hot water temperatures may allow the growth of infectious bacteria if not
properly disinfected.
CAUTION – Safe temperatures for swimming or aquatic exercise is around 80˚F.
AUTION – Risk of Electrical Shock. Do not leave audio compartment open.
C
Audio controls are not to be operated while inside the spa.
CAUTION – Replace components only with identical components.
WARNING – Risk of Electric Shock. Do not connect any auxiliary components (for
example, additional speakers, headphones, additional audio/ video components
etc.) to the system. These units are not provided with an outdoor antenna.
Do not service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
If the power supply cord(s) are damaged, water is entering the speaker, audio
compartment, or any other component in the electrical equipment compartment
area, the protective shield is showing signs of deterioration, or there are signs of
other potentially hazardous damage to the unit, turn off the circuit breaker from
the wall and refer servicing to qualified personnel.
DO NOT DIVE.
7
SAFETY INSTRUCTIONS
Important Safety
Instructions (cont.)
T he unit should be subjected to periodic routine maintenance once every quarter to
make sure that the it is operating properly.
DANGER – Risk of Electric Shock. A green colored terminal or a terminal marked G,
GR, Ground, Grounding or the symbol shown in Figure 14.1 of UL 1563 is located
inside the supply terminal box or compartment. To reduce the risk of electric shock,
this terminal must be connected to the grounding means provided in the electric
supply service panel with a continuous copper wire equivalent in size to the circuit
conductors supplying this equipment.
t least two lugs marked “Bonding Lugs” are provided on the external surface
A
or on the inside of the supply terminal box or compartment. To reduce the risk
of electric shock, connect the local common bonding grid in the area of the spa
to these terminals with an insulated or bare copper conductor not smaller than
8AWG.
ll field installed metal components such as rails, ladders, drains, or other similar
A
hardware within 3m of the spa shall be bonded to the equipment grounding bus
with copper conductors not smaller than 8AWG.
SAVE THESE INSTRUCTIONS
DO NOT DIVE.
8
SAFETY INSTRUCTIONS
Warning: Children should not use spas or hot tubs without adult supervision
Avertissement: Ne pas laisser les enfants utiliser une cuve de relaxation
sans surveillance
Warning: Do not use spas or hot tubs unless all suction guards are
installed to prevent body and hair entrapment.
Avertissement: Pour éviter que les cheveux ou une partie du corps
puissent être aspires, ne pas utiliser une cuve de relaxation si les grilles di prise
d’aspiration ne sont pas toutes en place
Warning: People using medications and/or having an adverse medical history should consult a physician before using a spa or hot tub.
Avertissement: Les personnes qui prennent des médicaments ou ont des
problémes de santé devraient consulter un médecin avant d’utiliser une cuve de
relaxation
Warning: People with infectious diseases should not use a spa or hot tub
Avertissement: Les personnes atteintes de maladies infectieuses ne
devraient pas utiliser une cuve de relaxation
Warning: To avoid injury exercise care when entering or exiting the spa or
hot tub.
Avertissement: Pour éviter des blessures, user de prudence en entrant
dans une cuve de relaxation et en sortant
Warning:
Do not use drugs or alcohol before or during the use of a spa
or hot tub to avoid unconsciousness and possible drowning
Avertissement: Pour éviter l’évanouissement et la noyade éventuelle, ne
prende ni drogue ni alcool avant d’utiliser une cuve de relaxation ni quand on s’y
trouve
Warning:
Pregnant or possibly pregnant women should consult a physician before using a spa or hot tub.
Avertissement: Les femmes enceintes, que leur grossesse soit confirmée
ou non, devraient consulter un médecin avant d’utiliser une cuve de relaxation
Warning: Water temperature in excess of 38˚C may be injurious to your
health
Avertissement: Il peut être dangereux pour la santé de se plonger dans
de l’eau a plus de 38˚C
Warning: Before entering the spa or hot tub measure the water temperature with an accurate thermometer
Avertissement: AVant d’utiliser une cuve de relaxation mesurer la
température de l’eau À l’aide d’un thermométre précis
DO NOT DIVE.
9
SAFETY INSTRUCTIONS
Warning: Do not use a spa or hot tub immediately following strenuous
exercise
Avertissement: Ne pas utiliser une cuve de relaxation immédiatement
aprés un exercise fatigant
Warning: Prolonged immersion in a spa or hot tub may be injurous to your
health
Avertissement: L’utilisation prolongée d’une cuve de relaxation peut
être dangereuse pour la santé
Warning: Do not permit electric appliances (such as light, telephone, radio,
or television) within 1.5 m of this spa or hot tub
Avertissement:
Ne pas placer d’appareil électrique (luminaire, téléphone,
radio, téléviseur, etc) À moins de 1.5 m de cette cuve de relaxation
Caution: Maintain water chemistry in accordance with manufacturer’s
instruction
Attention: La teneur de l’eau en matiéres dissoutes doit être conforme aux
directives du fabricant
Hyperthermia occurs when the internal temperature of the body reaches a level several
degrees above the normal body temperature of 37˚C. The symtoms of hyperthermia include
drowsiness, lethargy, and an increase in the internal temperature of the body. The effects of
hyperthermia include
(a) unawareness of impending hazard;
(b) failure to perceive heat;
(c) failure to recognize the need to exit spa;
(d) physical inability to exit spa;
(e) fetal damage in pregnant women; and
(f) unconsciousness and danger of drowning.
Warning:
The use of alcohol or drugs can greatly increase the risk of
fatal hyperthermia in hot tubs and spas
La Consommation d’alcool ou de drogue augmente considérablement les
risques d’hyperthermie mortelle dans une cuve de relaxation.
DO NOT DIVE.
10
SAFETY LITERATURE
There are additional available publications related to spa safety. These documents include
booklets entitled: “Children aren’t Waterproof;” “Pool and Spa Emergency Procedures for
Infants and Children;” “Layers of Protection;” and “Sensible Way to Enjoy Your Spa.” All of
these publications are published by National Spa and Pool Institute (NSPI) / Association of Pool
and Spa Professionals (APSP).
GLOSSARY OF SPA TERMINOLOGY
1. D
RAINING YOUR SPA. The drain is located behind the front panel on the
far right side, grasp the hose bib cap and turn it counter clockwise. Attach
a garden hose, if desired. Turn the black knob on the side of the valve a
quarter turn. Draining times may vary by model using the external hose
bib. A sump pump may also be used to drain the spa quickly.
2. MAIN PUMP. This produces water flow through the main jets in the spa.
The first pump may be operated on two speeds. Low speed will produce
efficient water circulation during filtration and gentle jet action. High speed
should be used for maximum jet action. The main pump is controlled by the “Jets” or “Jets I”
button on the Topside Control Panel.
3. S ECONDARY PUMP. This produces water flow through the other jet system in the spa
(if applicable). The second pump operates similar to the main pump and is controlled by the
“Aux” button on the Topside Control Panel.
4. Circulation Pump (if so equipped). This produces water flow through the heater in the
spa and provides the water flow necessary to actuate the ozone. This fractional hp pump
runs 24 hours a day to provide filtration and heating.
5. PUMP UNION. These are used by service personnel to easily service the pump(s).
6. HEATER UNION. These are used by service personnel to easily service the heater.
7. OZONATOR. Your optional ozonator will operate in conjunction with your filtration system.
DO NOT DIVE.
11
Electrical Installation Requirements
CLS 360 and CLS 415
HAVE YOUR ELECTRICIAN READ THE FOLLOWING INFORMATION
BEFORE INSTALLATION BEGINS
Electrical connections made improperly, or the use of wire gauge sizes for incurring power which are too small, may continually blow fuses in the electrical
equipment box, may damage the internal electrical controls an components, may
be unsafe and in any case will void your warranty.
It is the responsibility of the spa owner to ensure that electrical connections are
made by a qualified electrician in accordance with the National Electrical Code and
any local and state electrical codes in force at the time of installation.
These connections must be made in accordance with the wiring diagrams found
inside the control box. This equipment has been designed to operate on 60Hz.
alternating current only, 120 volts are required. Make sure that power is not
applied while performing any electrical installation. A copper bonding lug has
been provided on the electrical equipment pack to allow connection to local
ground points. The ground wire must be at least 14 AWG copper wire (unless
local or state codes require a heavier gauge wire) and must be connected securely to a grounded metal structure such as a cold water pipe. All equipment packs
are wired for 120 VAC only. The only electrical supply for your spa must include
a 15 AMP switch or circuit breaker to open all non-grounded supply conductors
to comply with section 422-20of the National Electrical Code. The disconnect
must be readily accessible to the spa occupants, but installed at least five feet
from the spa. A Ground-Fault Circuit Interrupter (GFCI) (provided with the spa)
must be used to comply with section 680-42 of the National Electrical Code. A
ground fault is a current leak from any one of the supply conductors to ground.
A GFCI is designed to automatically shut off power to a piece of equipment
when a ground fault is detected.
Power hook-up to the spa must be 120 volt 2 wire plus ground (14 AWG copper).
Route the cable into the equipment area for final hook-up to terminals inside the
control panel. The spa must be hooked up to a “dedicated” 120 volt, 15 amp.
The term “dedicated” means the electrical circuit for the spa is not being used
for any other electrical items (patio lights, appliances, garage circuits, etc.). If the
spa is connected to a non-dedicated circuit, overloading will result in “nuisance
tripping”which requires resetting of the breaker switch at the house electrical
panel.
Rev. 11/07
Permanently Connected Equipment Assembly with Pump(s), Heaters, Luminaine, Ozone, Spa
Side Control(s), Pump shut off device.
NOTE: Some of the above components may be optional or not available with every spa model.
DO NOT DIVE.
12
Electrical Installation Requirements
CLS 524, CLS 730, CLS 730L, CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055
HAVE YOUR ELECTRICIAN READ THE FOLLOWING INFORMATION BEFORE
INSTALLATION BEGINS
Electrical connections made improperly, or the use of wire gauge sizes for incurring
power which are too small, may continually blow fuses in the electrical equipment
box, may damage the internal electrical controls and components, may be unsafe and
in any case will void your warranty.
It is the responsibility of the spa owner to ensure that electrical connections are made
by a qualified electrician in accordance with the National Electrical Code and any local
and state electrical codes in force at the time of installation.
These connections must be made in accordance with the wiring diagrams found
inside the control box. This equipment has been designed to operate on 60Hz. alternating current only, 240 volts are required. Make sure that power is not applied
while performing any electrical installation. A copper bonding lug has been provided
on the electrical equipment pack to allow connection to local ground points. The
ground wire must be at least 8 AWG copper wire (unless local or state codes require
a heavier gauge wire) and must be connected securely to a grounded metal structure
such as a cold water pipe. All equipment packs are wired for 240 VAC only. The only
electrical supply for your spa must include a 50 AMP switch or circuit breaker to open
all non-grounded supply conductors to comply with section 422-20 of the National
Electrical Code. The disconnect must be readily accessible to the spa occupants, but
installed at least five feet from the spa. A Ground-Fault Circuit Interrupter (GFCI) must
be used to comply with section 680-42 of the National Electrical Code. A ground
fault is a current leak from any one of the supply conductors to ground. A GFCI is
designed to automatically shut off power to a piece of equipment when a ground
fault is detected.
Power hook-up to the spa must be 240 volt 3 wire plus 8 AWG copper ground (6 AWG
copper) 8 AWG copper ground.
Route the cable into the equipment area for final hook-up to terminals inside the control panel. The spa must be hooked up to a “dedicated” 240 volt, 50 amp breaker
and GFCI. The term “dedicated” means the electrical circuit for the spa is not being
used for any other electrical items (patio lights, appliances, garage circuits, etc.). If the
spa is connected to a non-dedicated circuit, overloading will result in “nuisance tripping” which requires resetting of the breaker switch at the house electrical panel.
Rev. 11/07
Permanently Connected Equipment Assembly with Pump(s), Heaters, Luminaine, Ozone, Spa
Side Control(s), Pump shut off device, and Audio/Video Components.
NOTE: Some of the above components may be optional or not available with every spa model.
DO NOT DIVE.
13
WIRING SCHEMATIC - 240 VOLT SPA HOOK-UP
Balboa
Instruments
G.F.C.I Breaker Box
Incorporated
Wire Key
Green (Ground)
Red (Hot)
Black (Hot)
White (Neutral)
50
TEST
House Breaker Box
50
ON
OFF
OFF
ON
OFF
ON
GRN (GROUND)
ON
OFF
BLK (HOT)
ON
OFF
RED (HOT)
WHT
GRN
BLK (HOT)
GRN (GROUND)
RED (HOT)
WHT
BLK (HOT)
RED (HOT)
Spa System Box
TB1
1
2
3
4
5
WHITE (NEUTRAL)
BLACK (HOT)
RED (HOT)
GREEN (GROUND)
NOTE: For a 240 V
dedicated hook-up, the
white neutral wire is
not required between
the G.F.C.I. and the
system box.
WHT (NEUTRAL)
IDF00007.mac 6/17/97
*A
ctual wiring of GFCI will vary by manufacturer of GFCI. The GFCI shown is a Square D. Improper wiring of GFCI may result in permanent damage to spa system box. Repair / replacement of spa system
box is not covered under warranty when damage results from improper wiring.
DO NOT DIVE.
14
SITE PREPARATION / GENERAL GUIDELINES
Portable spa installation is simple when properly planned. To that end, it is important that you read
the following information carefully and consult with your spa dealer.
1) Access - The actual dimensions of your new
spa will determine the amount of space that
is needed in moving the spa from curbside to
its final installation area. Be sure to measure
side yard dimensions, gates or doors and
vertical obstructions such as roof overhangs
and overhead cables. Any other space limiting obstacles such as trees or shrubs must be
evaluated.
GENERAL CONSIDERATIONS FOR
OUTDOOR INSTALLATION
2) If the spa is being installed indoors, dimension limitations such as stairs, ceilings and
walls must be taken into consideration.
Please have your spa dealer or delivery service review site or installation plans prior to
delivery.
• View from inside spa and view of spa from
inside of home
3) Surface/Pad Requirements - When your new
spa is filled with water and bathers, it may
weigh as much as several tons. It is imperative that the base beneath the spa can support the entire weight. The spa must be on a
uniformly firm, continuous, and level surface.
The recommended foundation is a concrete
pad with a minimum thickness of four (4)
inches with steel reinforcement bars crossed
throughout the pad.
• Proximity to dressing rooms and bathrooms
Proper planning will increase your total enjoyment factor with your new spa. Listed below
are some additional items to consider when
planning your installation.
• How spa will complement landscaping and
vice versa
• Exposure to sunlight and shading from trees
• Privacy
• Getting to spa from house and return
• Storage for spa chemicals
• Local building codes (if applicable)
• Power cable
GENERAL CONSIDERATIONS FOR
INDOOR INSTALLATION
Installing your spa indoors creates an entirely
different set of considerations. With proper
planning, no matter what room your spa goes
in, it will be your favorite room.
IMPORTANT
When installing your spa indoors, on a wood
deck, or balcony, the same load requirements
must be met. Total load may be as much as 90
pounds per square foot. You should speak with
a qualified contractor or your local building
department to confirm that your surface is adequate for supporting a spa. Be sure to locate
your spa so that equipment remains above
grade and is not subject to flooding.
• Work with your spa dealer and contractor to
insure all local building, electrical and plumbing codes are met
• Plan for a floor drain to drain off excess water
or for draining and cleaning your spa
• A ventilation fan may be necessary due to
high humidity created by your spa
• Finished material in your spa room should
also be capable of withstanding increased
humidity
The equipment side(s) of the spa must be
accessible in the event that future service is
needed. Periodical maintenance checks require
entry into the equipment bay. When possible,
it is wise planning for the future to leave 2 feet
of access to all sides of the spa in the event
your spas plumbing requires maintenance. Your
spa warranty does not cover the cost of providing access for service.
DO NOT DIVE.
• If you are installing your spa indoors, always
be aware that if you splash water into the
speaker compartments of the spa, water will
run down through the speaker drain which
drains below the spa in the corner where the
speakers are located. Please be aware of this
as any damage is not covered by the warranty.
This could cause unwarranted damage.
15
INSTALLATION INSTRUCTIONS
1.) P ut spa in final position that allows for access to equipment
and spa components.
2.) R
emove front side panel (This is the side where the main topside
control panel is located) so electrical can be hooked up to the
spa system pack. Panels are removed by unscrewing the screws in
the corner sections and side panels. (using #2 square bit). Using a
Phillips screwdriver may result in stripping of the screw.
3.) F ill spa at least 1” above filter. We recommend filling the spa through the filter area.
4.) T urn the power on to the spa. Spa will go through its priming mode. This lasts approximately 5
minutes.
5.) It may be necessary to bleed air from the pump(s) on your spa if, after start up, your spa pumps
do not operate.
Due to the nature of water flow and hydro-therapy pumps, please be advised that air locking
of pumps may occur. We have taken measures to reduce the possibility of this, but it still may
occur, especially after refilling a spa. This is not a service covered under warranty.
To relieve an airlock situation, loosen the union (see picture) on the discharge of the pump (see
arrow on picture of pump below). Water should leak out. Tighten the union and test the pump
for proper jet flow. If needed repeat process.
Pump Union
Airlock
6.) A
djust water chemistry according to the instructions provided in the “Water Quality
Maintenance Section” (page 20).
7.) Y
our spa water will heat approximately 4° - 7° per hour, for all 240V spas. This varies depending on the size of the spa. Step into the soothing waters of your new spa!
Relax and enjoy.
DO NOT DIVE.
16
WATER CHEMISTRY TERMS YOU SHOULD KNOW
Before jumping into the "Spa Water Maintenance",
here are some terms to help you.
1. Parts per million, or ppm: This is a form of measurement used in most pool or spa chemical readings. Best described as any one million like items of equal size and make up, next to one unlike
item , but of equal size. This would be one part per million.
2. Average size spa: What is it? The national spa and pool institute (NSPI) states; 350 to 400 U.S.
gallons is average. As a general rule, chemical dosages are the same for any spa between 100
and 500 U.S. gallons. Spas over 500 U.S. gallons the dosage would be double. Under 100 U.S.
gallons would be on a case by case basis.
3. Total Alkalinity: This is a measurement of the ability of the water to resist changes in pH. Put
another way, it is the water’s ability to maintain proper pH. Total alkalinity is measured in parts
per million from 0 to 400 plus, with 80 to 150 ppm being the best range for spas. With low
alkalinity, the pH will flip, or change back and forth, and be hard to control. With high alkalinity
it becomes extremely difficult to change the pH.
4. p
H or potential hydrogen: This is a measurement of the active acidity in the water, or it is the
measurement of the concentration of active hydrogen ions in the water. The greater the concentration of active hydrogen ions, the lower the pH. pH is not measured in parts per million, but
on a scale from 0 to 14, with 7 being the neutral. In spas when ever possible, a measurement
between 7.2 and 7.8 is best. Whenever possible, it should be between 7.4 and 7.6. With low
pH, the results can be corroded metals, etched and stained plaster, stained fiberglass or acrylic,
eye / skin irritation, rapid chlorine or bromine loss, and total alkalinity destruction. With high pH,
the results can be cloudy water, eye / skin irritation, scale formation and poor chlorine or bromine efficiency.
5. S hocking: This is when you add either extra chlorine (superchlorinate) by raising the chlorine level
above 8 ppm, or add a non-chlorine shock (potassium monoperoxysulfate or potassium monopersulfate) to burn off the chloramines or bromamines. A non-chlorine shock acts by releasing
oxygen in the water, which serves the same function as chlorine. The advantage to using nonchlorine shock, is you can enter the water within 15 minutes after shocking. Using chlorine,
you must wait until the total chlorine reading is below 5 ppm. One thing to remember, a nonchlorine shock will not kill bacteria or disinfect.
6. S equestering: This can be defined as the ability to form a chemical complex which remains in
solution, despite the presence of a precipitating agent (i.e. calcium and metals). Common names
for sequestering chemicals are; minquest, stain and scale control, metal-x, spa defender, spa
metal gone, (etc.).
7. F iltration: Filters are necessary to remove particles of dust, dirt, algae, etc. that are continuously
entering the water. If the spa is not operated long enough each day for the filter to do a proper
job, this puts a burden on the chemicals, causing extra expense. Filtration time will depend on
the spa size, pump and filter size, and of course, bather load. A spare cartridge should be kept
on hand to make it easy to frequently clean the cartridge without the need for a long shut
down. This will also allow the cartridge to dry out between usages, which will increase the
cartridge life span as much as twice. Replace the cartridge when the pleats begin to deteriorate. Cartridge cleaning should be done a minimum of once a month. More often with a heavy
bather load.
DO NOT DIVE.
17
WATER CHEMISTRY TERMS YOU SHOULD KNOW
Before jumping into the "Spa Water Maintenance",
here are some terms to help you.
8. S anitizers: This is what kills the germs and bacteria that enter the water from the environment
and the human body.
A. Chlorine
1. Only one type is approved for spa use
a. Sodium dichlor which is granular, fast dissolving and pH neutral chlorine.
2. Chlorine is an immediate sanitizer.
B. Bromine
1. T wo types of tablets.
a. Hydrotech
b. Lonza
2. Bromine is a slow dissolve chemical and may take a few days to develop a reserve or
reading in the water.
9. Total dissolved solids (TDS): Materials that have been dissolved by the water. i.e. Like what happens when you put sugar in coffee or tea.
10. Useful life of water (in days): Water should be drained at least once every 180 days. Useful life
may vary by usage and bather load.
11. Defoamer: Foaming may be caused by body oils, cosmetics, lotions, surface cleaners, high pH
or algeacides as well as other organic materials. Low levels of calcium or sanitizer can also
cause foaming. Also, double rinse your bathing suits as they will hold residual soap after being
washed.
12. Calcium hardness: Water that is too hard (over 250 ppm) can promote scale formation in components and on spa surface. Water that is too low (below 180 ppm) may also shorten the life
of metal components on the spa.
NOTE: Always leave spa cover open for 15 min. after adding chemicals to prevent off gas
from damaging your spa cover, spa pillows, and other critical parts.
DO NOT DIVE.
18
THE ADVANTAGES OF ECO PUR™ Filtration
THE ADVANTAGES OF ECO PUR™ Filtration
Eco Pur™ water filter system is designed to reduce the use of chemicals in your spa. You will still
be required, periodically, based on usage to add a small amount of chlorine to oxidize organic
compounds in the water. The Eco Pur™ filter system will not eliminate the need to maintain proper
water chemistry but can make the maintenance a more natural experience.
Features
• The Eco Pur™ filter system will not oxidize organic compounds and will require periodic doses of
chlorine to assist in the sanitization and oxidation processes required to maintain clear spa water.
• Eco Pur™ filter system will not alter the ph of spa water. The Eco Pur™ filter system will actually
aid in stabilizing the ph. Eco Pur™ does not alter the (TDS) total dissolved solids.
• The main function of the Eco Pur™ filter system is to provide clean and clear spa water.
Proper chemical balance and filtration are also key components in maintaining healthy spa
water. Always ensure that the ph and total alkalinity of the spa water is checked and balanced
at all times. To ensure proper filtration, clean the regular filter cartridge with a “filter cleaner”
every 30 days and rinse the Eco Pur™ cartridge with a hose to remove any buildup of
containments. (Do not soak the Eco Pur™ cartridge in filter cleaner.) If water appears to
be visually cloudy, dull, or has an odor, shock the spa water with 1 ounce of chlorine*
to remove excessive containments. When cleaning filters, be sure to never have the
pumps (including the circulation pump) running without the filters in place. Failure
to do so may result in debris being drawn into the pumps causing unwarranted damage.
• Helps remove calcium carbonate and hydrogen sulphide from spa water to protect heaters
and equipment from precipitation.
• Helps stabilize the pH and alkalinity of the spa water.
• Helps reduce chemical usage and still provide safe odor-free water.
• Helps deplete excess chlorine after chemical shock to prevent damage to skin,
hair, and swim wear.
• Helps to produce ultra clean and clear water.
Note: Eco Pur™ filters are not recommended for use with Bromine. Consult your dealer for additional
information.
Master Spas, Inc. products are not designed to be used with Biquanides. These chemicals are found
in SoftSwim® and Baqua Spa® products. Due to adverse effects from these types of sanitizers, the
use of these products may void the spa warranty.
DO NOT DIVE.
19
DO NOT DIVE.
23
WATER QUALITY MAINTENANCE START-UP
for eco pur™ Water filter system
Step 1:
Your spa should be filled using a Pre-filter, which can be obtained from your local
dealer. This Pre-filter will help remove many of the minerals existing in the water,
which will make adjusting the water balance easier after a new fill. Never use more
then 50% softened water when filling the spa.
Step 2:
During the initial filling of the spa, add a sequestering agent to combat suspended
minerals in the water. The agents are sold under many different names such as Mineral
Clear, Stain and Scale, Metal Protect, and other brands. Allow water to circulate and
filter for at least 12 hours before adding any other chemicals.
Step 3:
Test water for pH, total Alkalinity, and Calcium hardness. The pH should be 7.2 - 7.8
and the total Alkalinity 80-150 PPM. Calcium hardness levels should be maintained
between 150 and 250 PPM (part per million).
Step 4:
Adjust pH and total Alkalinity (TA) utilizing the directions on the chemical bottles.
Wait 15 minutes, test and adjust if necessary.
Step 5:
It may be necessary to retest and add additional chemicals to get to the proper levels
in Step 3.
Step 6:
Add 2 ounces of concentrated chlorinating granules* (sodium Dichlor-s-triazinetreone)
on initial start up to begin sanitizing the spa water. Always refer to the chemical manufactures dosage recommendations listed on the container. It is important not to add
the chlorinating granules until the pH, alkalinity and calcium hardness have been
adjusted to their proper levels.
*special noTe:
We recommend a minimum level of 1.0 ppm residual chlorine be maintained in spa water. Always refer to the
chemical manufacturer’s dosage recommendations listed on the container.
When adding chlorine or non-chlorine shock/oxidizer always broadcast across the water while the pumps are
running.
The quantities of sanitizer and oxidizer shown in this manual are for 500 gallon spas and may have to be adjusted depending on the actual amount of water that your spa holds. See the specifications section of this manual
for the correct gallons of your spa.
The concentration of active ingredients in spa chemicals varies by manufacturer. The amounts of sanitizer suggested in this manual are based on spa chemicals that have the active ingredient percentages listed below:
Chlorine
Non-Chlorine Shock/ Oxidizer
Active ingredient:
Active ingredient:
Sodium dichlor ................................. 99.9%
Potassium peroxymonosulfate ....................... 42.8%
Other ingredients ................................ 1%
Inert ingredients ............................................ 57.2%
Total ............................................... 100%
Total............................................................ 100%
DO NOT DIVE.
24
20
WATER QUALITY MAINTENANCE SCHEDULE - ECO PUR™
BeFOre eaCH use
Check spa water with a test strip for proper sanitation levels and adjust accordingly
to the proper levels. Free chlorine level should be 1-3 ppm.
ONCe a WeeK
Add 1 ounce of non-chlorine shock/oxidizer* or chlorine* to spa to help maintain the water quality.
3 tIMes a WeeK
Test water using chemical test strips. Adjust sanitizer, pH and Alkalinity accordingly. The total alkalinity should be between 80 - 150 ppm and the PH should be between 7.2 - 7.8.
ONCe a MONtH
Soak your regular filter elements overnight in a container with spa Filter Cleaner and then rinse
with clean water. For best results, allow the filter to dry before re-inserting. (The Eco Pur™ mineral
element should never be cleaned in a filter cleaner. Just rinse with water.) When cleaning filters, be
sure to never have the pumps (including the circulation pump) running without the filters in place.
Failure to do so may result in debris being drawn into the pumps causing unwarranted damage.
See the “clean your filter elements” in the maintenance section of this manual for more information.
eVerY 180 DaYs
Drain and refill your spa with fresh water, install a new Eco Pur™ filter element, clean the regular
filter, and repeat start up procedure. The regular filter should be replaced at least once every year.
aFter eaCH use
Add 1 ounce of non-chlorine shock/oxidizer* or 1/2 ounce of chlorine* to the spa water.
*sPeCIaL NOte:
We recommend a minimum level of 1.0 ppm residual chlorine be maintained in spa water. Always refer to the
chemical manufacturer’s dosage recommendations listed on the container.
When adding chlorine or non-chlorine shock/oxidizer always broadcast across the water while the pumps are
running.
The quantities of sanitizer and non-chlorine oxidizer shown in this manual are for 500 gallon spas and may have
to be adjusted depending on the actual amount of water that your spa holds. See the specifications section of
this manual for the correct gallons of your spa.
The concentration of active ingredients in spa chemicals varies by manufacturer. The amounts of sanitizer suggested in this manual are based on spa chemicals that have the active ingredient percentages listed below:
Chlorine
Non-Chlorine Shock/ Oxidizer
Active ingredient:
Active ingredient:
Sodium dichlor ................................. 99.9%
Potassium peroxymonosulfate ....................... 42.8%
Other ingredients ................................ 1%
Inert ingredients ............................................ 57.2%
Total ............................................... 100%
Total............................................................ 100%
DO NOT
NOT DIVE.
DIVE.
DO
21
26
WATER
WATER QUALITY
QUALITY MAINTENANCE
MAINTENANCE SCHEDULE
SCHEDULE -ECO
ECO PUR™
PUR™ (continued)
(continued)
as NeeDeD
If water looks hazy, check PH and Total Alkilinity, and treat with 1 ounce of chlorine*. Always refer
to the chemical manufactures dosage recommendations listed on the container.
These are general recommendations for water quality maintenance that may vary by usage and
or bather load. Depending on bather load and frequency of use, drain and refill times may vary as
well as the frequency of cleaning your filters.
A defoamer may be used when excessive foaming occurs. Over use of a defoamer will result
in cloudy, milky water.
use ONLY sPa CHeMICaLs
Do not use chemicals designed for use in swimming pools.
With a spa you are working with a small volume of hot water compared to a large volume of
relatively cool water in a swimming pool. Because of this chemicals will have a shorted life span
and bacteria can grow more quickly than in a swimming pool. A spa is less forgiving then a pool
and requires that whatever is put into it have a pH as close to neutral as possible. That is why only
chemicals made for spas should be used. Always refer to the chemical manufactures dosage recommendations listed on the container.
*sPeCIaL NOte:
We recommend a minimum level of 1.0 ppm residual chlorine be maintained in spa water. Always refer to the
chemical manufacturer’s dosage recommendations listed on the container.
When adding chlorine or non-chlorine shock/oxidizer always broadcast across the water while the pumps are
running.
The quantities of sanitizer and oxidizer shown in this manual are for 500 gallon spas and may have to be adjusted depending on the actual amount of water that your spa holds. See the specifications section of this manual
for the correct gallons of your spa.
The concentration of active ingredients in spa chemicals varies by manufacturer. The amounts of sanitizer suggested in this manual are based on spa chemicals that have the active ingredient percentages listed below:
Chlorine
Non-Chlorine Shock/ Oxidizer
Active ingredient:
Active ingredient:
Sodium dichlor ................................. 99.9%
Potassium peroxymonosulfate ....................... 42.8%
Other ingredients ................................ 1%
Inert ingredients ............................................ 57.2%
Total ............................................... 100%
Total............................................................ 100%
DO
DO NOT
NOT DIVE.
DIVE.
27
22
27
SPA WATER MAINTENANCE
TROUBLE-SHOOTING GUIDE
Problem
Possible Causes
How To Fix It
Chlorine / Bromine Odor
• Excessive Chlorine or
bromine levels
• Shock water with non-chlorine
shock treatment
• Low pH
• Adjust pH if necessary
• Low levels of sanitizer
• Shock water with non-chlorine
shock treatment or adjust sanitizer levels
Water Odor
Cloudy Water
• pH out of range
• Adjust pH level if necessary
• Bacteria or algae growth
• Adjust sanitizer if necessary
• Dirty filters or
inadequate filtration
• Clean filters and adjust filtration
times
• Water chemistry not balanced
• Adjust chemistry levels
• Suspended particles or
organic materials
• Add spa clarifier (see dealer)
• Old water
• Change spa water
Scum Ring Around Spa
• Build up of oils, dirt and
organic elements
• Wipe off with a clean towel add
an enzyme product.
Eye / Skin Irritation
• Unsanitary water
• Shock spa with non-chlorine
shock
• Free chlorine level above 5 ppm
• Allow level to drop below 5 ppm
• Poor sanitizer / pH levels
• Adjust according to spa test strip
results
• High levels of body oils,
lotions, soap, etc.
• Add small amount of defoamer
Foaming
Recommended Levels of Chemical
Chlorine 1.0 - 3.0 ppm
pH 7.2 - 7.8
Total Alkalinity 80 - 150 ppm
Calcium Hardness 180 - 250 ppm
DO NOT DIVE.
23
WHY ARE CHEMICALS IMPORTANT IN A SPA
1. E vaporation: As water evaporates, only pure water evaporates, leaving the salts, minerals, metals, and any unused chemicals behind. Adding water adds more salts, minerals, and metals. In
time, the water can become saturated with these dissolved solids and can cause stains or scale
to form on the walls of the spa or a scale build up inside the equipment. Colored or cloudy
water, and possible corrosion of plumbing and fittings may also occur.
2. H
eat: Heat causes much quicker evaporation and also will cause minerals and metals to precipitate out of solution.
3. Air: Dust and airborne dirt particles are introduced into the spa.
4. Environment: The environment surrounding the spa can also impact the water quality. Items such
as pollen, grass, sand, dirt, lawn fertilizer, airborne dust, insects, leaves, and pets can all affect
the water quality of the spa.
Remember:
The maintenance routines set forth in this manual may need to be adjusted depending on how
much the spa is being used.
DO NOT DIVE.
24
MAINTENANCE RECOMMENDATIONS
Your spa requires periodic draining and cleaning to ensure a safe, healthy environment. It is recommended that you clean your spa at least every 180 days. Heavy bather load will require cleaning it
more often.
DRAINING YOUR SPA
• See page 11.
CLEAN YOUR SPA SURFACE
• With a soft cloth, wipe down the spa surface with a non-abrasive spa surface cleaner that may
be purchased through your local spa dealer. Do not use paper towels. Be sure to rinse residue
from spa surface.
• If your spa has developed an oily or chalky residue at the waterline it may require special treatment. Consult your dealer.
REFILL YOUR SPA
• Be sure to close the drain valve.
• Fill the spa with water. Be sure water level is above skimmer opening to the minimum safe water
level label.
• Refer to the start-up section for specific instructions.
CLEAN YOUR FILTER ELEMENT (also reference page 48)
• The filter elements are one of the most important components of your spa. Not only are they
essential for clean water, but they also extend the life of the spa equipment. You filter elements
should be cleaned on a regular basis, once a month on average with normal usage. With heavy
use the filters may need to be cleaned more often. Do not soak Eco Pur filters in filter cleaner.
• Turn off the spa before servicing filters. Never leave to the spa running when removing the filters. Debris can be pulled into the plumbing system and cause unwarranted damage.
• Remove filter element.
• With a garden hose, spray the element under pressure. Periodically, the element needs to be
soaked in a filter cleaner compound. Do not soak Eco Pur filters in filter cleaner. Check with your
dealer for details on cleaning and/or filter replacement recommendations.
• Replace filter element.
• Be sure water level is adequate.
• Turn spa on.
• Only clean the ECO PUR filter element with water, do not use chemical cleaners.
CARE OF YOUR SPA PILLOWS
• Your spa pillows need to be rinsed periodically to remove any chemical residue. This should help
to eliminate pillows becoming stiff and discolored.
• If the spa will not be used for a period of time, the pillows should be removed to extend their
useful life.
NOTE: Do not cover the spa for 15 minutes after adding chemicals as the off gas can
cause unwarranted damage.
DO NOT DIVE.
25
WINTERIZING YOUR SPA
Many people find they enjoy using their spa more in the winter than any other time. Your spa is
designed to be used year round in any type of climate.
*However, if you decide you don’t want to use your spa in the winter, you must drain it and follow the winterizing steps listed below:
1. Drain your spa completely using the drain valve (see “To Drain Your Spa” on page 11) or use an
inexpensive submersible pump that you can buy from your dealer or your local hardware store.
2. Use a shop vac to get all standing water out of your unit.
3. Remove access panels from equipment area.
4. Loosen all pump unions
5. Remove winterizing plug from face of the pump(s) where applicable.
6. Using your shop vac in a blowing mode, insert the hose into the nozzle of each jet and blow the
trapped water from the lines into the interior of the spa.
7. After this is completed, use the shop vac to remove any standing water in the spa and in the
equipment area.
8. Clean the spa with a soft cloth and a non-abrasive spa surface cleaner.
9. Replace access panels.
10. Cover spa to prevent water from entering the spa.
* Disclaimer: We do not recommend winterizing your spa. If you choose to do so, any damage that
may result is not covered under the spa warranty.
DO NOT DIVE.
26
SPA - SPECIFICATIONS
Spa
Dimensions
Electrical
Requirements
Water Capacity
(gallons)
Weight
Dry/Full (lbs.)
Therapy
Pumps
Jet
Count
CLS 360
78"x 78"x 33"
120V, 15 Amp
265
400 / 2,608
1
18
CLS 415
83"x 48"x 30"
120V, 15 Amp
150
425 / 1,675
1
15
CLS 524
66"x 84"x 32"
240V, 50 Amp
215
515 / 1,791
1
24
CLS 730
84"x 84"x 36"
240V, 50 Amp
360
630 / 3,618
1
30
CLS 730L
84"x 84"x 36"
240V, 50 Amp
345
660 / 3,524
1
30
CLS 738
84"x 84"x 36"
240V, 50 Amp
360
670 / 3,658
2
38
CLS 738L
84"x 84"x 36"
240V, 50 Amp
345
700 / 3,564
2
38
CLS 855
94"x 94"x 28"
240V, 50 Amp
435
775 / 4,386
2
55
CLS 855L
94"x 94"x 36"
240V, 50 Amp
425
750 / 4,630
2
55
CLS 1055
120"x 94"x 39"
240V, 50 Amp
620
970 / 6,135
2
55
DO NOT DIVE.
27
SPA - CONTROLS: CLS 360 & CLS 415
Initial Start-up
When your spa is first actuated, it will go into Priming mode, indicated by “Pr ” The Priming mode
will last for less than 5 minutes (press “warm” or “cool” to skip Priming Mode) and then the spa
will begin to heat the spa and maintain the water temperature in the Standard mode.
Temp (80°F - 104°F / 26°C - 40°C)
The start-up temperature is set at 100F°/37°C. The last measured temperature is constantly displayed on the LCD.
Note that the last measured spa temperature displayed is current only when the low speed of
pump 1 has been running for at least 2 minutes.
To display the set temperature, press the “warm” or “cool” pad.
Temperature setting is accomplished by pressing “warm” to increase the temperature or “cool” to
decrease the temperature.
After three seconds, the LCD will stop flashing and display the current spa temperature.
Jets
Touch the “Jets” button once to turn pump 1 on or off, and to shift between low and high
speeds. If left running, the low speed of the pump will automatically turn off after 4 hours, and
the high speed will automatically turn off after 15 minutes.
Light (if equipped)
Press the “Light” button to turn the light on and off. If left on, the light automatically turns off
after 4 hours.
L.E.D. Light (if installed)
Press the “Light” button to turn the light on and off. If you wish to change the “function” of the
lights, turn the lights off, then on within 5 seconds. If you wish to leave the lights in the same
“function” setting for the next use, turn the lights off and do not turn back on for at least 5 seconds.
DO NOT DIVE.
28
SPA - CONTROLS: CLS 360 & CLS 415
Mode
Mode is changed by pressing the “warm” or “cool” button, then pressing the “light” button.
Standard mode is programmed to maintain the desired temperature. Note that the last measured
spa temperature displayed is current only when the low speed of pump 1 has been running for at
least 2 minutes. “St” will be displayed momentarily when you switch into Standard Mode.
Economy mode heats the spa to the set temperature only during filter cycles. “Ec” will display solid
when temperature is not current, and will alternate with temperature when temperature is current.
Sleep mode heats the spa to within 20°F/10°C of the set temperature only during filter cycles. “SL”
will display solid when temperature is not current, and will alternate with temperature when temperature is current.
Preset Filter Cycles
The first filter cycle begins 6 minutes after the spa is energized. The second filter cycle begins 12
hours later. Filter duration is programmable for 2, 4, 6, 8 hours or for continuous filtration (indicated by “FC ”). The default filter time is 2 hours.
To program, press “warm” or “cool” then “Jets.” Press “warm” or “cool” to adjust. Press “Jets”
to exit programming. At the beginning of each filter cycle the pump(s) purge for 30 seconds; the
pump purges for 5 minutes. The only effect filter duration has is: 1) During the filter, the lowspeed of pump 1 never turns off, and 2) In Economy and Sleep Modes, heating only occurs during
the filter cycle.
Freeze Protection
If the temperature sensors detect a drop to below 44°F/6.7°C within the heater, the pump will
automatically activate to provide freeze protection. The equipment stays on until 4 minutes after
the sensors detect that the spa temperature has risen to 45°F/7.2°C or higher.
DO NOT DIVE.
29
SPA – DIAGNOSTIC MESSAGES: CLS 360 & CLS 415
MESSAGE
DO NOT DIVE.
MEANING
ACTION REQUIRED
No message on display.
Power has been cut off
to the spa.
The control panel will be disabled until
power returns. Spa settings will be
preserved until next power up.
Temperature
unknown.
After the pump has been running
for 2 minutes, the temperature will
be displayed.
“Overheat” - The spa
has shut down. One of
the sensors has detected
118°F/48°C at the
heater.
DO NOT ENTER THE WATER. Remove the
spa cover and allow water to cool. Once
the heater has cooled, reset by pushing any
button. If spa does not reset, shut off the
power to the spa and call your dealer or service organization.
“Overheat” - The spa
has shut down. One of
the sensors has detected
that the spa water is
110°F/43°C.
DO NOT ENTER THE WATER. Remove the
spa cover and allow water to cool. At
107°F/42°C, the spa should automatically
reset. If spa does not reset, shut off the
power to the spa and call your dealer
or service organization.
“Ice” - Potential freeze
condition detected.
No action required. The pump(s) will
automatically activate regardless of
spa status.
Spa is shut down. The
sensor that is plugged
into the Sensor “A” jack
is not working.
If the problem persists, contact your dealer
or service organization. (May appear temporarily in an overheat situation and disappear
when the heater cools.)
Spa is shut down. The
sensor that is plugged
into the Sensor “B” jack
is not working.
If the problem persists, contact your dealer
or service organization. (May appear temporarily in an overheat situation and disappear
when the heater cools.)
30
SPA – DIAGNOSTIC MESSAGES: CLS 360 & CLS 415
MESSAGE
MEANING
ACTION REQUIRED
Sensors are out of
balance. If alternating
with spa temperature, it
may just be a
temporary condition.
If flashing by itself,
spa is shut down.
If the problem persists, contact your dealer
or service organization.
A significant difference
between temperature
sensors has been detected. This could indicate
a flow
problem.
Check water level in spa. Refill if
necessary. If the water level is okay, make
sure the pumps have been primed. If problem persists, contact your dealer or service
organization.
Persistent low flow problems. (Displays on the
fifth occurrence of “ ”
message within 24
hours.) Heater is shut
down, but other spa
functions continue to run
normally.
Follow action required for “ ”
message. Heating capability of the spa will
not reset automatically; you may press any
button to reset. Check filters
for possible blockage.
Possible inadequate
water, poor flow, or air
bubbles in detected in
the heater. Spa is shut
down for 15 minutes.
Check water level in spa. Refill if
necessary. If water level is okay, make sure
the pump(s) have been primed. Press any
button to reset, or this message will automatically reset within 15 minutes. If problem
persists, contact your dealer or service organization.
Inadequate water detected in heater. (Displays on
third occurrence of “
” message.) Spa is
shut down.
Follow action required for “ ”
message. Spa will not automatically reset.
Press any button to reset.
Warning! Shock Hazard! No User Serviceable Parts. Do not attempt service of this control system.
Contact your dealer or service organization for assistance. Follow all owner’s manual power connection instructions. Installation must be performed by a licensed electrician and all grounding
connections must be properly installed.
DO NOT DIVE.
31
Main Menus
CLS 524, CLS 730, CLS 730L, CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055
NavigatioN
Navigating the entire menu structure
is done with 2 or 3 buttons on the control
panel.
Some panels have separate WARM (Up)
and COOL (Down) buttons, while others
have a single Temperature button. In the
navigation diagrams Temperature buttons
are indicated by a single button icon.
Panels that have two Temperature buttons (Warm and Cool) can use both of them to simplify
navigation and programming where a single Temperature icon is shown.
The LIGHT Button is also used to choose the various menus and navigate each section.
Typical use of the Temperature button(s) allows changing the Set Temperature while the numbers
are flashing in the LCD. Pressing the LIGHT button while the numbers are flashing will enter the
menus.
The menus can be exited with certain button presses. Simply waiting for several seconds will return
the panel operation to normal.
Power-up Screens
Each time the System powers up, a series of numbers is displayed.
(SeePage
Page3).
33).
After the startup sequence of numbers, the system will enter Priming Mode (See
Key
Indicates Flashing or Changing Segment
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Waiting time that keeps the last change to a menu item.
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
Main Screen
READY
RANGE FLTR1
SET
RANGE
While the Temperature is
still flashing, press Light.
SET
Main Screen
READY
RANGE FLTR1
Waiting Several Seconds in the Main Menu
will allow the display to revert to the Main Screen.
Most changes are not saved unless Light
is pressed.
Refer to Key above.
SET READY
DO NOT DIVE.
32
23
Fill it up!
CLS 524, CLS 730, CLS 730L, CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055
PreParatioN aNd FilliNg
Fill the spa to its correct operating level. Be sure to open all valves and jets in the plumbing system
before filling to allow as much air as possible to escape from the plumbing and the control system
during the filling process.
After turning the power on at the main power panel, the top-side panel display will go through
specific sequences. These sequences are normal and display a variety of information regarding the
configuration of the hot tub control.
PrimiNg mode
This mode will last for 4-5 minutes or you can manually exit the priming mode after the pump(s)
have primed.
Regardless of whether the priming mode ends automatically or you manually exit the priming
mode, the system will automatically return to normal heating and filtering at the end of the
priming mode. During the priming mode, the heater is disabled to allow the priming process to be
completed without the possibility of energizing the heater under low-flow or no-flow conditions.
Nothing comes on automatically, but the pump(s) can be energized by pushing the “Jet” buttons.
If the spa has a 24 hour Circ Pump, it can be activated by pressing the “Light” button during
Priming Mode.
PrimiNg the PumPs
As soon as the above display appears on the panel, push the “Jet” button once to start Pump 1
in low-speed and then again to switch to high-speed. Also, push the Pump 2 or “Aux” button,
if you have a 2nd pump, to turn it on. The pumps will now be running in high-speed to facilitate
priming. If the pumps have not primed after 2 minutes, and water is not flowing from the jets
in the spa, do not allow the pumps to continue to run. Turn off the pumps and repeat the
process. Note: Turning the power off and back on again will initiate a new pump priming session.
Sometimes momentarily turning the pump off and on will help it to prime. Do not do this more
than 5 times. If the pump(s) will not prime, shut off the power to the spa and follow the
instructions shown for removing air locks in the installation instructions section of this manual.
Important: A pump should not be allowed to run without priming for more than 2 minutes. Under
NO circumstances should a pump be allowed to run without priming beyond the end of the 4-5
minute priming mode. Doing so may cause damage to the pump and cause the system to energize
the heater and go into an overheat condition.
exitiNg PrimiNg mode
You can manually exit Priming Mode by pressing a “Temp” button (Up or Down). Note that if you
do not manually exit the priming mode as described above, the priming mode will be automatically
terminated after 4-5 minutes. Be sure that the pump(s) have been primed by this time.
Once the system has exited Priming Mode, the top-side panel will momentarily display the set
temperature but the display will not show the temperature yet, as shown below. This is because
the system requires approximately 1 minute of water flowing through the heater to determine the
water temperature and display it.
or
READY
RANGE
DO
DO NOT
NOT DIVE.
DIVE.
READY
RANGE
33
24
Spa Behavior
CLS 524, CLS 730, CLS 730L, CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055
PumPs
Press the “Jets 1” button once to turn pump 1 on or off, and to shift between low- and highspeeds if equipped. If left running, the pump will turn off after a time-out period. The pump 1
low-speed will time out after 30 minutes. The high-speed will time out after 15 minutes.
If the spa is in Ready Mode (See page 36)
6), Pump 1 low may also activate for at least 1 minute
every 30 minutes to detect the spa temperature (polling) and then to heat to the set temperature
if needed. When the low-speed turns on automatically, it cannot be deactivated from the panel,
however the high speed may be started.
Circulation Pump
The 24 hour circ pump operates continuously with the exception of turning off for 30 minutes at
a time when the water temperature reaches 3°F (1.5°C) above the set temperature (most likely to
happen in very hot climates).
FiltratioN aNd ozoNe
On non-circ systems, Pump 1 low and the ozone generator will run during filtration. On 24 hour
circ systems, the ozone will run with the 24 hour circ pump.
The system is factory-programmed with two filter cycles that will run 10 minutes after power-up.
The filter duration is programmable. (See
(See page
page 37)
7)
At the start of each filter cycle, Pump 2 (if there is one) will run briefly to purge its plumbing to
maintain good water quality.
Freeze ProteCtioN
If the temperature sensors within the heater detect a low enough temperature, then the pump(s)
automatically activate to provide freeze protection. The pump(s) will run either continuously or
periodically depending on conditions.
DO NOT DIVE.
34
25
Temperature and Temp Range
CLS 524, CLS 730, CLS 730L, CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055
adjustiNg the set temPerature
When using a panel with Up and Down buttons (Temperature buttons), pressing Up or Down
will cause the temperature to flash. Pressing a temperature button again will adjust the set
temperature in the direction indicated on the button. When the LCD stops flashing, the spa
will heat to the new set temperature when required.
If the panel has a single temperature button, pressing the button will cause the temperature to
flash. Pressing the button again will cause the temperature to change in one direction (e.g. UP).
After allowing the display to stop flashing, pressing the Temperature Button will cause the
temperature to flash and the next press will change the temperature in the opposite direction
(e.g. DOWN).
The temperature can be set between 80˚F and 104˚F.
Press-aNd-hold
If a Temperature button is pressed and held when the temperature is flashing, the temperature
will continue to change until the button is released. If only one temperature button is available
and the limit of the Temperature Range is reached when the button is being held, the progression
will reverse direction.
DO NOT DIVE.
35
26
Mode – Ready and Rest
CLS 524, CLS 730, CLS 730L, CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055
In order for the spa to heat, a pump needs to circulate water through the heater. The pump that
performs this function is known as the “heater pump.”
The heater pump can be either a 2-Speed Pump 1 or a 24 hour circulation pump.
If the heater pump is a 2-Speed Pump 1, READY Mode will circulate water every 1/2 hour, using
Pump 1 Low, in order to maintain a constant water temperature, heat as needed, and refresh the
temperature display. This is known as “polling.”
REST Mode will only allow heating during programmed filter cycles. Since polling does not occur,
the temperature display may not show a current temperature until the heater pump has been
running for a minute or two.
24 Hour Circulation Mode (See
(See page
Page34,
4, under Pumps, for other circulation modes)
If the spa is configured for 24HR circulation, the heater pump runs continuously. Since the heater
pump is always running, the spa will maintain set temperature and heat as needed in Ready Mode,
without polling.
In Rest Mode, the spa will only heat to set temperature during programmed filter times, even
though the water is being filtered constantly when in Circulation Mode.
Sub-Menu Detail – MODE – Ready and Rest
Key
Indicates Flashing or Changing Segment
Main Screen
READY
Indicates Alternating or Progressive Message - every 1/2 second
RANGE
SET
RANGE FLTR1
While the Temperature is
still flashing, press Light
repeatedly until MODE
appears in the LCD.
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Waiting time that keeps the last change to a menu item.
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
Main Screen
To Set
SET READY
SET
*****
Waiting
REST
Several Seconds
Reverts to Original Setting
REST RANGE FLTR1
Toggle between READY and REST
Pressing Light when the display is toggled will go to Main Screen.
To next item in
Main Menu
If not toggled
READY Mode will allow the spa to Poll and determine a need for heat. The panel will maintain a “current” temperature display.
REST Mode will not Poll and will only heat during filter cycles. The panel will not display a current temperature at all times.
Main Screen
1 Hour
REST RANGE FLTR1
REST RANGE
REST RANGE
REST RANGE
REST RANGE
REST RANGE
The Main Screen will display RUN PUMP FOR TEMP if the filtration pump has not run for over 1 hour.
The Main Screen will display normally during Filter Cycles or when the spa is in use.
If the filtration pump has been off for an hour or more, when any function button, EXCEPT Light, is pressed on the panel,
the pump used in conjuncton with the heater will run so that temperature can be sensed and displayed.
ready-iN-rest mode
READY/REST appears in the display if the spa is in Rest Mode and Jet 1 is pressed. It is assumed
that the spa is being used and will heat to set temperature. While Pump 1 High can be turned on
and off, Pump 1 Low will run until set temperature is reached, or 1 hour has passed. After 1 hour,
the System will revert to Rest Mode. This mode can also be reset by entering the Mode Menu and
changing the Mode.
Main Screen
REST RANGE
DO NOT
NOT DIVE.
DIVE.
DO
Main Screen
J
READY/REST RANGE
36
27
Flip (Invert Display)
CLS
524,
CLS 730, CLS
730L, CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055
Flip
(Invert
Display)
Key
Indicates Flashing or Changing Segment
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel configuration
Sub-Menu Detail – FLIP (Invert Display)
Waiting time that keeps the last change to a menu item.
time (depends on menu item) that reverts to original setting and
***** Waiting
ignores any change to that menu item.
Main Screen
READY
While the Temperature is
still flashing, press Light
repeatedly until FLIP
appears in the LCD.
RANGE
SET
RANGE FLTR1
Main Screen
or
Several Seconds
SET
READY
SET
To next item in
Main Menu
If not toggled
RANGE FLTR1
Toggle the inversion of the segmented characters
Pressing Light when the display is toggled will go to Main Screen.
Note:
Some panels may have a dedicated FLIP button, which allows the user to flip the display with a
single button-press.
Adjusting Filtration
maiN FiltratioN
Filter cycles are set using a duration. Each setting can be adjusted in 1-hour increments. Filter Cycle
1 and Filter Cycle 2 (if enabled) are set to the same duration.
Main Screen
READY
RANGE FLTR12
SET
While the Temperature is
still flashing, press Light
repeatedly until FLTR
appears in the LCD.
RANGE
Sets Filter length in hours
Main Screen
To Set
SET
FLTR12
*****
Waiting
READY
RANGE FLTR12
Several Seconds
Reverts to Original Setting
If Filter Cycle 2 is enabled, Filter 12 will appear in the LCD. If Filter is disabled, Filter 1 will appear.
Purge CyCles
In order to maintain sanitary conditions, secondary Pumps will purge water from their respective
plumbing by running briefly at the beginning of each filter cycle.
DO NOT DIVE.
37
DO NOT DIVE.
28
General Messages
CLS 524, CLS 730, CLS 730L, CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055
PrimiNg mode
Each time the spa is powered up, it will enter Priming Mode. The purpose of Priming Mode is to
allow the user to run each pump and manually verify that the pumps are primed (air is purged)
and water is flowing. This typically requires observing the output of each pump separately, and
is generally not possible in normal operation. Priming Mode lasts 4 minutes, but you can exit it
earlier by pressing any Temp button. The heater is not allowed to run during Priming Mode.
NOTE: If your spa has a 24 hour Circ Pump, it will turn on with Jets 1 in Priming Mode.
The 24 hour Circ Pump will run by itself when Priming Mode is exited.
or
READY
RANGE
READY
RANGE
Water temPerature is uNkNoWN
After the pump has been running for 1 minute, the temperature will be displayed.
READY
RANGE FLTR1
too Cold - Freeze ProteCtioN
A potential freeze condition has been detected, and all pumps are activated. All pumps are ON for
at least 4 minutes after the potential freeze condition has ended.
In some cases, pumps may turn on and off and the heater may operate during Freeze Protection.
This is an operational message, not an error indication.
Water is too hot (ohs)
One of the water temp sensors has detected spa water temp 110°F (43.3°C) and spa functions
are disabled. System will auto reset when the spa water temp is below 108°F (42.2°C). Check for
extended pump operation or high ambient temp.
* This message can be reset from the topside panel with any button press.
DO NOT DIVE.
29
38
Heater-Related Messages
Heater-Related
Messages
CLS 524, CLS 730, CLS 730L,
CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055
heater FloW is reduCed (hFl)
There may not be enough water flow through the heater to carry the heat away from the heating
element. Heater start up will begin again after about 1 min. See “Flow Related Checks” below.
heater FloW is reduCed (lF)*
There is not enough water flow through the heater to carry the heat away from the heating
element and the heater has been disabled. See “Flow Related Checks” below. After the problem
has been resolved, you must press any button to reset and begin heater start up.
heater may be dry (dr)*
Possible dry heater, or not enough water in the heater to start it. The spa is shut down for 15 min.
Press any button to reset the heater start-up. See “Flow Related Checks” below.
heater is dry*
There is not enough water in the heater to start it. The spa is shut down. After the problem has
been resolved, you must press any button to reset and restart heater start up. See “Flow Related
Checks” below.
heater is too hot (ohh)*
One of the water temp sensors has detected 118°f (47.8°C) in the heater and the spa is shut
down. You must press any button to reset when water is below 108°f (42.2°C). See “Flow Related
Checks” below.
a reset message may aPPear With other messages.
Some errors may require power to be removed and restored.
FloW-related CheCks
Check for low water level, suction flow restrictions, closed valves, trapped air, too many closed
jets and pump prime.
On some systems even when spa is shut down, some equipment may occasionally turn on to
continue monitoring temperature or if freeze protection is needed.
* This message can be reset from the topside panel with any button press.
DO NOT DIVE.
DO NOT DIVE.
39
29
Sensor-Related Messages
CLS 524, CLS 730, CLS 730L, CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055
READY
RANGE FLTR1
seNsor balaNCe is Poor
The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service.
seNsor balaNCe is Poor*
The temperature sensors are out of sync. The Sensor Balance is poor fault has been established for
at least 1 hour. Call for Service.
seNsor Failure – seNsor a, seNsor b
A temperature sensor or sensor circuit has failed. Call for Service.
Miscellaneous Messages
No CommuNiCatioNs
The control panel is not receiving communication from the System. Call for Service.
READY
RANGE FLTR1
°F or °C is rePlaCed by °t
The Control System is in Test Mode. Call for Service.
* This message can be reset from the topside panel with any button press.
DO NOT DIVE.
29
40
System-Related Messages
CLS 524, CLS 730, CLS 730L, CLS 738, CLS 738L, CLS 855, CLS 855L, CLS 1055
memory Failure - CheCksum error*
At Power-Up, the system has failed the Program Checksum Test. This indicates a problem with the
firmware (operation program) and requires a service call.
memory WarNiNg - PersisteNt memory reset*
Appears after any system setup change. Contact your dealer or service organization if this message
appears on more than one power-up, or if it appears after the system has been running normally
for a period of time.
memory Failure - CloCk error*
Contact your dealer or service organization.
CoNFiguratioN error – sPa Will Not start uP
Contact your dealer or service organization.
a PumP aPPears to be stuCk oN
Water may be overheated. POWER DOWN THE SPA. DO NOT ENTER THE WATER. Contact your
dealer or service organization.
a PumP aPPears to have beeN stuCk oN WheN sPa Was last
PoWered – m035
POWER DOWN THE SPA. DO NOT ENTER THE WATER. Contact your dealer or service organization.
* This message can be reset from the topside panel with any button press.
DO NOT DIVE.
29
41
standard fusion audio system
STANDARD FUSION AUDIO SYSTEM
MODEL: AQ-DM-3
FILE NAME: IB-DM-3_manual_103112A
Warning: Never remain in your spa longer than 15 minutes per session
LOCATION
OF
CONTROLS
when the water
temperature
is above 98˚F. If you wish to spend more
time in your spa, whether enjoying music, or just lounging, be sure to
keep the spa water at or below body temperature (98.6˚F).
*Please refer to your stereo Owner’s Manual for specific operations.
Optional Stereo Station
Your spa is equipped with a media locker station that will allow you to listen to personal selections
through the audio system of the spa.
The media locker station is compatible with most portable audio products. Master Spas, Inc. does not
guarantee compatibility with all portable audio products due to software changes and upgrades.
POWER ON
To activate the Digital Media Locker™, press the standby button on the locker, LED will turn red.
To turn on the stereo, press the ON/OFF button located on the door mounted keypad.
1. Press + (VOLUME UP) once to increase the volume by 3 decibels.
2. Press - (VOLUME DOWN) once to decrease the volume by 3 decibels. Press and hold either UP or
DOWN button on the Digital Media Locker™ to increase or decrease audio volume continuously.
3. Audio information is passed from you portable device via the 3.5mm connector inside
the locker door.
Buttons
Press once: toggle from Operation mode to Standby mode or vise versa.
Power
Volume
up
+
-
Volume
down
Press once: Volume UP a value
Press and hold: Fast volume up
Press once: Volume DOWN a value
Press and hold: Fast volume down
CAUTION – Risk of Electric Shock. Do not leave compartment door open.
CAUTION – Risk of Electric Shock. Replace components only with identical
components; and
Do not operate the Audio / Video controls while inside the spa.
LISTENING TO MP3
WARNING – Prevent Electrocution. Do not connect any auxiliary components (for example
1. Power
up the
Digitalheadphones,
Media Locker
. Audio / Video components, etc.) to the system.
cable,
additional
speakers,
additional
TM
2. Attach your MP3 or other Audio Player device to the 3.5mm connector.
NOTE: These units are not provided with an outdoor antennae; when provided, it should
be installed in accordance with article 810 of the National Electrical Code, ANSI / NFPA 70.
ADJUSTING
VOLUME
NOTE:
Do not service
thisLEVEL
product yourself as opening or removing covers may expose
you
to dangerous
voltage UP)
or other
injury. Refer
all servicing
to qualified service
+
1.
Press
(VOLUME
oncerisk
to of
increase
the volume
by 3 decibels.
personnel.
2. Press
-
(VOLUME DOWN) once to reduce the volume by 3 decibels.
DO
DIVE.
55the Digital Media Locker TM will
3. NOT
Press
and hold either UP or DOWN and
increase or decrease audio volume continuously.
DO NOT DIVE.
42
Always ensure to connect and disconnect your media player with dry hands.
deluxe
DELUXE fusion
FUSION audio
AUDIO system
SYSTEM
Warning: Never remain in your spa longer than 15 minutes per session when the water
temperature is above 98˚F. If you wish to spend more time in your spa, whether enjoying music,
or just lounging, be sure to keep the spa water at or below body temperature (98.6˚F).
*Please refer to your stereo Owner’s Manual for specific operations.
Optional Stereo Docking Station
Your spa is equipped with an iPod™ docking station that will allow you to listen to personal selections through the audio system of the spa. This audio system also has an FM only radio receiver
that can be used to listen to local FM broadcasts. Due to varying signal conditions the FM radio
reception may be limited.
The docking station is compatible with most iPod™ products. Master Spas, Inc. does not guarantee
compatibility with all iPod™ products due to software changes and upgrades.
The wireless remote provided with the spa is water resistant, but should never be left in the spa
when not in use.
Power On
To activate the Digital Media Locker™, press the on/off button, standby mode will be indicated by a
red LED. ON mode will be indicated by a blue LED. When the unit is in the standby position the red
LED will be lit.
Remote Synchronizing
Press and hold MODE button on the remote. The display will then show “pair”. Keep pressing this
key. Then press the power button on the locker from off(no light) to standby (red light)to pair with
the locker. If the pairing is successful it will show “welcome” and the LED on the locker will turn blue.
If pair is not successful. Please repeat the step above.
Each Digital Media Locker™ comes with a matching RF (Radio Frequency) Wireless LCD Remote control. This remote is required use any functions on the unit.For any additional remote controls, you will
need to activate/Synchronize those remote controls to the main unit by following the steps above.
The remote control uses state-of-the-art technology and will inform you if the dock is receiving the
command from the remote control. In any case,if the LCD displays “NO LINK” this means that your
Locker is off or remote control is out of reception range.
Each Digital Media Locker™ comes with a matching RF (Radio Frequency) Wireless LCD remote
control. This remote is required to use any functions on the unit. For any additional remote controls you will need to activate/synchronize those remote controls to the stereo by following the
steps above.
If you lose your remote control and buy a replacement, follow the steps above to pair/synchronize
before normal usage.
DO
DO NOT
NOT DIVE.
DIVE.
55
43
deluxe fusion audio system
ltem Description
DELUXE FUSION AUDIO SYSTEM
B
1
2
3
DIR-
REPEAT
DIR+
C
RANDOM
A
B
C
Buttons
Music Mode
Remote Control LCD
Remote Control Buttons
Battery Door.
FM Radio Mode
Power
Press once: toggle from Operation mode to Standby mode or vise versa.
12V trigger
/Random
Press once: random function
Press and hold: Toggle external power
Press once: No function.
Press and hold: Toggle external power
Press once: Volume UP a value
Press and hold: Fast volume up
Press once: Volume UP a value
Press and hold: Fast volume up
Press once: Volume DOWN a value
Press and hold: Fast volume down
Press once: Volume DOWN a value
Press and hold: Fast volume down
Press once: Change the source.
Press and hold: Pair
Press once: Change the source.
Press and hold: Pair
Press once: Enter BAL-FAD-DSP-LOUD-VOL
Press once: Enter BAS-TRE-BAL-FAD-DSP
-AREA-LOUD-DX-STEREO-VOL.
Volume
up
Volume
down
Mode
Audio
+
-
MODE
AUDIO
1/DIR-
1
Press once: back to previous folder.
Press and hold: back to previous folder.
Press once: Listen to the station which in the No.1
Press and hold: stored a station into No.1.
2/Repeat
2
Press once: repeat function.
Press and hold: repeat function.
Press once: Listen to the station which in the No.2
Press and hold: stored a station into No.2.
3/DIR+
3
Press once: to next folder.
Press and hold: to next folder.
Press once: Listen to the station which in the No.3
Press and hold: stored a station into No.3.
Fast
Rewind
Press once: Last track
Press and hold: Fast Rewind
Press once: seek down
Press and hold: change to manual scanning
Pause/
Play
Press once:Play/Pause
Press and hold:Play/Pause
Press once: toggle mute
Press and hold: toggle mute
Fast
Forward
Press once: Next track
Press and hold: Fast Forward
Press once: seek up.
Press and hold: change to manual scanning
If your music player is not an ipod, you will not be able to control track or recieve track
information
In order to prolong remote battery life the LCD will shut off in 20 seconds if no
other button is pressed. To turn remote back on press any key once and then
press the command desired.
Shut off DSP to access control of Bass and Treble control
5
CAUTION – Risk of Electric Shock. Do not leave compartment door open.
CAUTION – Risk of Electric Shock. Replace components only with identical
components; and
Do not operate the Audio / Video controls while inside the spa.
WARNING –
Prevent Electrocution. Do not connect any auxiliary components (for example
cable, additional speakers, headphones, additional Audio / Video components, etc.) to the system.
NOTE: These units are not provided with an outdoor antennae; when provided, it
should be installed in accordance with article 810 of the National Electrical Code, ANSI
/ NFPA 70.
NOTE: Do not service this product yourself as opening or removing covers may expose
you to dangerous voltage or other risk of injury. Refer all servicing to qualified service
personnel.
DO NOT DIVE.
44
56
SPA TROUBLE-SHOOTING GUIDE
NOTHING ON THE SPA OPERATES
1.) C
heck the control panel display for any messages. If there is a message, refer to the diagnostic
section. There you will find the meaning of the
message and what action is to be taken.
2.) If there is no message on your control panel, check and reset the GFCI and house breaker.
*The GFCI should be located in a weather proof box close to
the spa, but no closer than 5 ft.
If the spa does not respond, contact your local service company.
PUMP(S) DO NOT OPERATE
1.) P ress the “Jets” button on your control panel.
If you hear the pumps trying to operate:
A. Pump may need to be primed. See page 16.
If you do not hear anything from the pump, contact your local service company.
POOR JET PERFORMANCE
1.) Make sure pump is operating
2.) Check that the water level is adequate (up to minimum safe water level side)
3.) Make sure that the jets and air controls are open.
4.) Check for dirty filter. Clean if necessary.
DO NOT DIVE.
45
SPA TROUBLE-SHOOTING GUIDE
SPA NOT HEATING
* If the spas heater has failed, the majority of the time it will trip the GFCI breaker. If the spa is not
heating and has not tripped the breaker, please follow these steps:
1. Check the control panel for diagnostic messages. Refer to spa diagnostic message area in previous sections. Follow steps to alleviate message.
2. Check water set temperature at control panel.
3. Check for dirty filter. Clean if necessary.
4. Check “heat mode” the spa is set in. Spa should be in standard/ready mode.
5. Check the control panel for heater light indicator. If the light is on, the spa should be heating.
Wait a reasonable amount of time (approximately 1 hour) to see if the water temperature is
changing.
6. Check to make sure that the pump is primed.
7. Reset power to the spa at GFCI breaker.
8. If spa is still not heating, contact your dealer for service.
GFCI IS TRIPPING
A ground fault circuit interrupter (GFCI) is required by the National
Electrical Code for your protection. The tripping of the GFCI may be
caused by a component on the spa or by an electrical problem. Electrical
problems include but are not limited to, a faulty GFCI breaker, spa component, power fluctuations, or improper wiring. It may be necessary to
contact an electrician if your dealer recommends doing so.
DO NOT DIVE.
46
REGULAR MAINTENANCE PROCEDURES
Note: These are maintenance procedures are the responsibility of the spa owner to perform.
These procedures are not covered by the spa warranty.
CLEANING JETS
The majority of jets in your spa can individually be turned on/off. If
any of these jets become hard to turn, it will be necessary to remove
the jet to clean it as grit/sand and mineral deposit may be present.
Jets are removed by turning the collar and then pulling out the jet.
The jets in your spa can be removed for cleaning by unscrewing
them (counter clockwise) and then pulling out the jet. Some jets may
not be removable depending on the model.
To Clean Jets
Place the jet(s) in a bucket, fully immerse in white vinegar. Let the jet(s) soak overnight and then
rinse with water. Reinstall the jet(s). It may be necessary to clean grit and deposits from the white
jet body (mounted in the spa shell) by using a small bristled brush.
DRAINING YOUR SPA
The drain is located behind the front panel on the far right side, grasp
the hose bib cap and turn it counter clockwise. Attach a garden hose,
if desired. Turn the black knob on the side of the valve a quarter turn.
Draining times may vary by model using the external hose bib. A sump
pump may also be used to drain the spa quickly.
CARE OF YOUR SPA COVER
Always cover your spa when not in use. This will greatly reduce energy consumption and will cause
spa water to heat more rapidly. Water loss and chemical usage will also be reduced.
• Be sure to lock down all straps on cover after each use to prevent wind damage.
• Do not allow spa to sit uncovered in direct sunlight. This may cause damage
to exposed surfaces of spa and possible discoloration of spa fittings.
• Periodically hose off both sides of spa cover for maximum life of cover. Once a month use a vinyl
cleaner and conditioner on the vinyl portion of your cover. Rinse residue off.
• Keep cover open for 15 min. after adding chemicals to prevent off
gas damage.
NOTE: IF YOUR SPA IS GOING TO BE LEFT EMPTY FOR PROLONGED PERIODS, DO NOT REPLACE
COVER DIRECTLY ON SURFACE OF SPA. PLACE 2”-3” BLOCKS BETWEEN COVER AND SPA. THIS
ALLOWS FOR ADEQUATE VENTILATION OF COVER AND SPA.
NOTE: Do not cover the spa for 15 minutes after adding chemicals as the off gas can
cause unwarranted damage.
DO NOT DIVE.
47
REGULAR MAINTENANCE PROCEDURES
CARE OF YOUR SPA CABINET
Your quality Polymer Skirt simply needs to be hosed off periodically. No other maintenance is
required.
CLS 360 and CLS 415
All Other Models
FILTER CLEANING (CLS 360 and CLS 415)
NOTE: Never operate the spa without filter in place. If done, damage will result to pumps and
other components. We recommend having an extra filter to install when cleaning the filter.
1. Turn power off to the spa.
2. Remove any large or floating debris from the filter area.
3. Remove the gray top assembly by gently lifting up. Lift up and remove the weir assembly. This
will allow access to the filter cartridge. The filter cartridge can be removed for replacement or
cleaning by turning it counter clockwise.
CAUTION: Always make sure that the filter assembly is completely reassembled before operating the spa.
FILTER CLEANING All Eco Pur Equipped Spas
NOTE: Never operate the spa without filters in place. If done, damage will result to pumps and
other components. We recommend having an extra set of filters to install when cleaning the filters.
1. Turn power off to the spa.
2. Remove any large or floating debris from the filter area.
3. Remove the filters. Remember that the ECO PUR mineral filters should only be rinsed with clear
water and never soaked in a cartridge cleaner. The outer filters should be periodically rinsed and
soaked in a cartridge cleaner. Follow the instructions on the cartridge cleaner. The ECO PUR filters should be replaced every 6 months and the regular filter at least once every year.
DO NOT DIVE.
48
SPA CARE AND MAINTENANCE RECORD
DATE
DATE
DATE
Drain & Clean Spa
Clean Filter Cartridge
Soak Filter
Cartridge in Solution
Test GFCI
Clean and Condition
Spa Cover
Miscellaneous
Service
Miscellaneous
Service
DO NOT DIVE.
49
DATE
DATE
DATE DATE
DATE
SPA CARE AND MAINTENANCE RECORD
DATE
DATE
DATE
Drain & Clean Spa
Clean Filter Cartridge
Soak Filter
Cartridge in Solution
Test GFCI
Clean and Condition
Spa Cover
Miscellaneous
Service
Miscellaneous
Service
DO NOT DIVE.
50
DATE
DATE
DATE DATE
DATE
SPA CARE AND MAINTENANCE RECORD
DATE
DATE
DATE
Drain & Clean Spa
Clean Filter Cartridge
Soak Filter
Cartridge in Solution
Test GFCI
Clean and Condition
Spa Cover
Miscellaneous
Service
Miscellaneous
Service
DO NOT DIVE.
51
DATE
DATE
DATE DATE
DATE
SPA CARE AND MAINTENANCE RECORD
DATE
DATE
DATE
Drain & Clean Spa
Clean Filter Cartridge
Soak Filter
Cartridge in Solution
Test GFCI
Clean and Condition
Spa Cover
Miscellaneous
Service
Miscellaneous
Service
DO NOT DIVE.
52
DATE
DATE
DATE DATE
DATE
SPA OWNER’S MANUAL
Clarity Spas
are manufactured by Master Spas,
one of the world’s leading spa manufacturers.
6927 Lincoln Parkway
Fort Wayne, IN 46804
800.860.7727
The manufacturer reserves the right to change specifications or features without notice. As a manufacturer of spas and related products we stand behind every
product we produce pursuant to those representations which are stated in our written
limited warranty. Your dealer is an independent business person or company and not an
employee or agent of the manufacturer. We cannot and do not accept any responsibility or
liability for any other representations, statements or contracts made by any dealer beyond
the provisions of our written limited warranty.
Rev 11/12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement