MULTIQUIP DCA10SPX3 Specifications

MULTIQUIP DCA10SPX3 Specifications
OPERATION AND PARTS MANUAL
®
MODEL DCA10SPX3
60 Hz GENERATOR
(KUBOTA D1403 DIESEL ENGINE)
Revision #2 (01/17/11)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PAGE 2 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
SERVICE DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 3
TABLE OF CONTENTS
Here's How To Get Help .......................................... 3
Table Of Contents ................................................... 4
Parts Ordering Procedures ..................................... 5
Rules For Safe Operation .................................... 6-9
Towing Safety ........................................................ 10
Trailer Safety Guidelines .................................. 11-15
Trailer Wiring Diagram........................................... 16
Operation and Safety Decals ........................... 17-18
Specifications ........................................................ 19
General Information .............................................. 20
Major Components ............................................... 21
Dimensions ...................................................... 22-23
Controls and Indicators .................................... 24-25
Output Terminals .............................................. 26-27
Installation ........................................................ 28-29
Pre-Setup ......................................................... 30-33
Load Application ................................................... 34
Start up Procedure .......................................... 35-36
Shut down Procedure ........................................... 37
Maintenance .................................................... 38-39
Generator Wiring Diagram .................................... 40
Engine Wiring Diagram ......................................... 41
Troubleshooting (Engine) ................................. 42-43
Troubleshooting (Generator) ................................ 44
Explanation Of Codes In Remarks Column .......... 46
Suggested Spare Parts ......................................... 47
DCA-10SPX3
AC Generator
Generator Assembly ........................................ 48-49
Control Panel Assembly ................................... 50-51
Output Terminal Assembly ............................... 52-53
Engine and Radiator Assembly........................ 54-55
Battery Assembly ............................................. 56-57
Muffler Assembly ............................................. 58-59
Fuel Filter Assembly ........................................ 60-61
Enclosure Assembly ......................................... 62-63
Rubber Seal Assembly..................................... 64-65
Decal Assembly ............................................... 66-67
Kubota D1403 Engine
Crankcase Assembly ....................................... 68-69
Oil Pan Assembly ............................................. 70-71
Cylinder Head Assembly .................................. 72-73
Gear Case Assembly ....................................... 74-75
Main Bearing Case Assembly .......................... 76-77
Inlet Manifold Assembly ................................... 78-79
Exhaust Manifold Assembly ............................. 80-81
Valve and Rocker Assembly ............................ 82-83
Head Cover Assembly ..................................... 84-85
Camshaft Assembly ......................................... 86-87
Piston and Camshaft Assembly ....................... 88-89
Flywheel Assembly .......................................... 90-91
Starter Assembly ............................................. 92-93
Starter Components Assembly ........................ 94-95
Injection Pump 1 Assembly .............................. 96-97
Injection Pump 1 Assembly .............................. 98-99
Fuel Camshaft Assembly ............................. 100-101
Governor Assembly ..................................... 102-103
Speed Control Plate Assembly .................... 104-105
Engine Stop Lever Assembly ....................... 106-107
Stop Solenoid Assembly .............................. 108-109
Alternator Assembly ..................................... 110-111
Alternator Components Assembly ............... 112-113
Fan Assembly............................................... 114-115
Water Flange and Thermostat Assembly..... 116-117
Water Pump Assembly ................................. 118-119
Radiator Assembly ....................................... 120-121
Fuel Filter Assembly .................................... 122-123
Terms and Condition of Sale-Parts ..................... 124
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
www.multiquip.com
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Order via Internet (Dealers Only):
Best Deal!
Effective:
January 1st, 2006
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: [email protected]
com.
Order parts on-line using Multiquip’s SmartEquip website!
■ View Parts Diagrams
■ Order Parts
■ Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Goto www.multiquip.com and click on
Order Parts to log in and save!
Note: Discounts Are Subject To Change
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Note: Discounts Are Subject To Change
Order via Phone: Domestic (US) Dealers Call:
1-800-427-1244
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
Dealer Name and Address
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
Quantity, Part Number and Description of Each Part
❒
Specify Preferred Method of Shipment:
✓ UPS/Fed Ex
✓ DHL
■ Priority One
✓ Truck
■ Ground
■ Next Day
■ Second/Third Day
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 5
RULES FOR SAFE OPERATION
CAUTION:
Failure to follow instructions in this manual
may lead to serious injury or even death!
This equipment is to be operated by trained
and qualified personnel only! This
equipment is for industrial use only.
The following safety guidelines should always be used when
operating the DCA-10SPX3 portable generator:
GENERAL SAFETY
■ DO NOT operate or service this equipment before
reading this entire manual.
■ This equipment should not be operated by persons under 18
years of age.
■ NEVER operate this equipment without proper
protective clothing, shatterproof glasses,
steel-toed boots and other protective devices
required by the job.
■ NEVER operate this equipment when not
feeling well due to fatigue, illness or
taking medicine.
■ NEVER operate this equipment under
the influence or drugs or alcohol.
■ NEVER use accessories or attachments, which are not
recommended by MQ Power for this equipment. Damage to
the equipment and/or injury to user may result.
■ Manufacture does not assume responsibility for any accident
due to equipment modifications.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ Always check the machine for loosened threads or bolts before
starting.
■ NEVER touch the hot exhaust manifold,
muffler or cylinder. Allow these parts to
cool before servicing engine or
generator.
■ High Temperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
■ The engine of this generator requires an adequate free flow
of cooling air. Never operate the generator in any enclosed or
narrow area where free flow of the air is restricted. If the air
flow is restricted it will cause
serious damage to the
generator or engine and may
cause injury to people. The
generator engine gives off
DEADLY carbon monoxide
gas.
CAUTION:
Always refuel in a well-ventilated area, away
from sparks and open flames.
■ Always use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the
machine. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
■ NEVER operate the generator in an
explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■ Topping-off to filler port is dangerous, as it tends to spill fuel.
PAGE 6 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
RULES FOR SAFE OPERATION
CAUTION:
CAUTION:
DO NOT touch or open any of the below
mentioned components while the generator
is running. Always allow sufficient time for
the engine and generator to cool before
performing maintenance.
Radiator
■ NEVER touch output terminals during operation. This is
extremely dangerous. Always stop the machine when contact
with the output terminals is required.
1. Radiator Cap - Removing the radiator cap while the
engine is hot will result in high pressurized, boiling water
to gush out of the radiator, therefore causing severe
scalding to any persons in the general area of the
generator.
CAUTION:
■ Backfeed to a utility system can cause electrocution
and/or property damage. Do not connect to any
building's electrical system except through an approved
device or after building main switch is opened.
CAUTION:
2. Coolant Drain Plug - Removing the coolant drain plug
while the engine is hot will result in hot coolant to gush
out of the coolant drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
3. Engine Oil Drain Plug - Removing the engine oil drain
plug while the engine is hot will result in hot oil to gush
out of the oil drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
■ Never use damaged or worn cables when connecting power
tools or equipment to the generator. Make sure power
connecting cables are securely connected to the generator's
output terminals, insufficient tightening of the terminal
connections may cause damage to the generator and
electrical shock.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 7
RULES FOR SAFE OPERATION
Battery
CAUTION:
■ Never over fill the battery with water above
the upper limit.
The battery has acids that can cause injury to the eyes and skin.
To avoid eye irritation, always wear safety glasses. Use well
insulated gloves when picking up the battery. Use the following
guidelines when handling the battery:
1. DO NOT drop the battery. There is the possibility of risk
the battery may explode.
2. DO NOT expose the battery to open flames, sparks,
cigarettes etc. The battery contains combustible gases
and liquids. If these gases and liquids come in contact
with a flame or spark, an explosion could occur.
3. Always keep the battery charged. If the battery is not
charged, a buildup of combustible gas will occur.
■ NEVER Run engine without air filter. Severe engine damage
may occur.
■ Always service air cleaner frequently to prevent carburetor
malfunction.
■ Always disconnect the battery before performing service on
the generator.
■ Always be sure the operator is familiar with proper safety
precautions and operations techniques before using generator.
■ Always store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
■ DO NOT leave the generator running in the manual mode
unattended.
■ DO NOT allow unauthorized people to operate this
equipment.
■ Always read, understand, and follow procedures in Operator’s
Manual before attempting to operate equipment.
■ Always be sure the operator is familiar with proper safety
precautions and operations techniques before using generator.
■ Refer to the Kubota Engine Owner's Manual for engine
technical questions or information.
Loading and Unloading (Crane)
■ Before lifting, make sure the generator's lifting hook is secure
and that there is no apparent damage to the generator itself
(loose screws, nuts and bolts). If any part is loose or damaged,
please take corrective action before lifting.
■ Always drain fuel prior to lifting.
■ Always make sure crane or lifting device has been properly
secured to the hook of guard frame on generator.
4. Always keep battery charging and booster cables in good
working condition. Repair or replace all worn cables.
■ NEVER lift the machine while the engine is running.
5. Always recharge the battery in an open air environment,
to avoid risk of a dangerous concentration of combustible
gases.
■ When lifting the generator, always use the balanced centerpoint suspension hook and lift straight upwards.
6. In case the battery liquid (dilute sulfuric acid) comes in
contact with clothing or skin, rinse skin or clothing
immediately with plenty of water.
7. In case the battery liquid (dilute sulfuric acid) comes in
contact with your eyes, rinse eyes immediately with
plenty of water, then contact the nearest doctor or
hospital, and seek medical attention.
■ Use adequate lifting cable (wire or rope) of sufficient strength.
■ NEVER allow any person or animal to stand underneath the
machine while lifting.
■ When loading the generator on a truck, be sure to use the
front and back frame bars as a means to secure the generator
during transport.
PAGE 8 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
RULES FOR SAFE OPERATION
Transporting
■ Always shutdown engine before transporting.
■ Tighten fuel tank cap securely.
Maintenance Safety
■ NEVER lubricate components or attempt service on a
running machine.
■ Drain fuel when transporting generator over long distances
or bad roads.
■ Always allow the machine a proper amount of time to cool
before servicing.
■ Always tie-down the generator during transportation by
securing the generator.
■ Keep the machinery in proper running condition.
■ If generator is mounted on a trailer, make sure trailer complies
with all local and state safety transportation laws. See page
10 for basic towing procedures.
Emergencies
■ Always know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department.
■ Fix damage to the machine immediately and always replace
broken parts.
■ Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel,
coolant and fuel filters.
■ DO NOT use plastic containers to dispose of hazardous
waste.
■ DO NOT pour waste, oil, coolant or fuel directly onto the
ground, down a drain or into any water source.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 9
DCA-10SPX3 — TOWING
■ ALWAYS attach trailer's safety chain to bumper of towing
vehicle.
Towing Safety Precautions
CAUTION :
Check with your county or state safety
towing regulations department before
towing your generator. Vehicle towing
codes and regulations can vary from state
to state.
To reduce the possibility of an accident while transporting
the generator on public roads, always make sure the trailer
and the towing vehicle are in good operating condition and
both units are mechanically sound.
The following list of suggestions should be used when towing
your generator:
■ Make sure the hitch and coupling of the towing vehicle are
rated equal to, or greater than the trailer "gross vehicle weight
rating" (GVWR).
■ ALWAYS inspect the hitch and coupling for wear. NEVER
tow a trailer with defective hitches, couplings, chains etc.
■ Check the tire air pressure on both the towing vehicle and
the trailer. Also check the tire tread wear on both vehicles.
■ ALWAYS make sure the vehicle and trailer directional,
backup, brake, and trailer lights are connected and are
working properly.
■ The maximum speed (unless otherwise posted) for highway
towing is 45 MPH. Recommended off-road towing is not to
exceed 10 MPH or less, depending on type of terrain.
■ Place chocked blocks underneath wheel to prevent rolling,
while parked.
■ Place support blocks underneath the trailer's bumper to
prevent tipping, while parked.
■ Use the trailer's hand winch to adjust the height of the trailer,
then insert locking pin to lock wheel stand in place, while
parked.
■ Avoid sudden stops and starts. This can cause skidding, or
jackknifing. Smooth, gradual starts and stops will improve
gas milage.
■ Avoid sharp turns to prevent rolling.
■ Remove wheel stand when transporting.
■ DO NOT transport generator with fuel in tank.
■ ALWAYS make sure the trailer is equipped with a "Safety
Chain".
Figure 1. DCA-10SPX3 and Towing Trailer
PAGE 10 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — TRAILER-SAFETY GUIDELINES
Frame Length - This measurement is from the ball
hitch to the rear bumper (reflector).
ALWAYS make sure the trailer is in good 5. Frame Width - This measurement is from fender to
operating condition. Check the tires for
fender.
proper inflation and wear. Also check the 6.
Jack Stand - Trailer support device with maximum
wheel lug nuts for proper tightness.
pound requirement from the tongue of the trailer.
7. Coupler - Type of hitch used on the trailer for towing.
Explanation of Chart:
8. Tire Size - Indicates the diameter of the tire in inches
This section is intended to provide the user with trailer ser(10,12,14, etc.), and the width in millimeters
vice and maintenance information. The service and main(175,185,205, etc.). The tire diameter must match the
tenance guidelines referenced in this section apply a wide
diameter of the tire rim.
range of trailers. Remember periodic inspection of the trailer 9. Tire Ply - The tire ply (layers) number is rated in letters;
will ensure safe towing of the equipment and will prevent
2-ply,4-ply,6-ply, etc.
damage to the equipment and personal injury.
10. Wheel Hub - The wheel hub is connected to the trailer’s
axle.
It is the purpose of this section to cover the major mainte- 11. Tire Rim - Tires mounted on a tire rim. The tire rim must
nance components of the trailer. The following trailer commatch the size of the tire.
ponents will be discussed in this section:
12. Lug Nuts - Used to secure the wheel to the wheel hub.
Always use a torque wrench to tighten down the lug
 Brakes
nuts. See Table 4 and Figure 5 or lug nut tightening and
 Tires
sequence.
 Lug Nut Torquing
13. Axle - Indicates the maximum weight the axle can sup Suspension
port in pounds, and the diameter of the axle expressed
 Electrical
in inches (see Table 3). Please not that some trailers
 Brake Troubleshooting Tables
have a double axle. This will be shown as 2-6000 lbs.,
meaning two axles with a total weight capacity of 6000
Use the following definitions with reading Table 1.
pounds.
1. Fuel Cell - Provides an adequate amount of fuel for 14. Suspension - Protects the trailer chassis from shocks
the equipment in use. Fuel cells must be empty when
transmitted through the wheels. Types of suspension
transporting equipment.
used are leaf, Q-flex, and air ride.
2. Braking System - System employed in stopping the 15. Electrical - Electrical connectors (looms) are provided
trailer. Typical braking systems are electric, surge, hywith the trailer so the brake lights and turn signals can
draulic, hydraulic-surge and air.
be connected to the towing vehicle.
3. GVWR- Gross Vehicle Weight Rating (GVWR), is the 16. Application - Indicates which units can be employed
maximum number of pounds the trailer can carry, inon a particular trailer.
cluding the fuel cell (empty).
CAUTION:
4.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 11
DCA-10SPX3 —TRAILER-SPECIFICATIONS
Table 1. Specifications
MOD EL
APPLIC ATION
FU E L
C E LL
B R AK E
SYSTEM
GVWR
FR AME
LEN GTH
FR AME
WID TH
JAC K
STAN D
TR LR -10-15
TLG-12, D C A15,
TLW-300
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TR LR -10X
TLG-12, D C A15,
TLW-300
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TR LR -10XF
TLG-12, D C A15,
TLW-300
51 GAL
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TR LR -225W
D C A-10
NO
NO
2200LB S
85"
42"
800LB .
FULL TILT WHEEL
B LW-400
BLW-400
NO
ELEC TRIC
2700LB S
W/MAST 154"
W/O 124"
55"
(78" TALL)
800LB .
FULL TILT WHEEL
TR LR -15XF
D C A-15
41 GAL
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TR LR -50X
D C A-25
NO
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TR LR -50XF
D C A-25
41 GAL
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TR LR -25SB T
D C A-25
NO
NO
2990LB S
120"
66"
800LB .
FULL TILT WHEEL
TR LR -70W
D C A-45, -60, 70
NO
SURGE
7000LB S
186"
77"
2000LB .
FLAT PAD
TR LR -70X
D C A-45, -60, 70
OPT
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TR LR -70XF
D C A-45, -60, 70
53 GAL
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TR LR -100XF
D C A-100, 125
150 GAL
HYD RAULIC SURGE
7000LB S
190"
76"
2000LB .
FLAT PAD
TR LR -85/125
D C A-85, 100,
125
145 GAL
HYD RAULIC
10000LB S
186"
77"
2000LB .
FLAT PAD
TR LR -150XF
D C A-150, 180
200 GAL
HYD RAULIC SURGE
11160LBS
204"
84"
5000 LB .
FLAT PAD
TR LR -220XF
D C A-220
250 GAL
HYD RAULIC SURGE
14000LB S
222"
83"
5000 LB .
FLAT PAD
TR LR -300XF
D C A-300
250 GAL
HYD RAULIC SURGE
18000LB S
238"
83"
5000 LB .
FLAT PAD
TR LR -400XF
D C A-400
350 GAL
ELEC TRIC
18000LB S
238"
83"
5000 LB .
FLAT PAD
TR LR -600XF
D C A-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
TR LR -800SX
D C A-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
PAGE 12 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 —TRAILER-SPECIFICATIONS
Table 1.S pecifications (C on't)
M O D EL
C O U P LE R
TIR E S
W H E E LS
A X LE
H U B S S U S P E N S IO N
E LE C TR IC A L
TR LR -10W
2" B A LL C LA S S
2 A D JU S TA B LE
175-13C
13"X 4.50"
2200# 2X 2
5 LU G
3 LE A F
4 W IR E LO O M W /
4 P O LE FLAT
TR LR -10
2"B A LL C LA S S
2 A D JU S TA B LE
175-13C
13"X 4.5"
2200#2X 2
5 LU G
3 LE A F
4 P O LE FLAT
TR LR -10X F
2"B A LL C LA S S
2 A D JU S TA B LE
175-13C
13"X 4.5"
2200#2X 2
5 LU G
3 LE A F
4 P O LE FLAT
TR LR -225W
2"B A LL C LA S S
2 A D JU S TA B LE
175-13B
13X 4.5"
2200#2X 2
5 LU G
Q FLE X
4 P O LE FLAT
TR LR -B LW
400
2"B A LL C LA S S
2 A D JU S TA B LE
175-13C
13 X 4.5"
2200#2X 2
5 LU G
3 LE A F
4 P O LE FLAT
TR LR -50X
2" B A LL C LA S S
B 78-13LR C
13"X 4.50"
3500lbs.
2-3/8"
5 LU G
4 LE A F
4 P O LE R U B B E R
FLAT
TR LR -50X F
2" B A LL C LA S S
B 78-13LR C
13"X 4.50"
3500lbs.
2-3/8"
5 LU G
4 LE A F
4 P O LE R U B B E R
FLAT
TR LR -70W
2" B A LL C LA S S
3" A D JU S TA B LE
205-14C
B IA S (4)
14"X 5"
3500lbs.
3"
5 LU G
5 LE A F
4 P O LE R U B B E R
FLAT
TR LR -70X
2" B A LL C LA S S
3" A D JU S TA B LE
205-14C
B IA S (4)
14"X 5"
3500lbs
3"
5 LU G
5 LE A F
4 P O LE R U B B E R
FLAT
TR LR -70X F
2" B A LL C LA S S
3" A D JU S TA B LE
205-14C
B IA S (4)
14"X 5"
3500lbs.
3"
5 LU G
5 LE A F
4 P O LE R U B B E R
FLAT
TR LR -100X F
A D JU S TA B LE 2-5/6
O P T 3" E YE
205-15C
B IA S (4)
14"X 5.5"
3500lbs
3"
5 LU G
5 LE A F
4 W IR E LO O M
TR LR -85/125
A D JU S TA B LE 2-5/6
O P T 3" E YE
S T225/75R 15D
R A D IA L (4)
14"x6"
(2)-6000lbs
6 LU G
7 LE A F
4 W IR E LO O M
TR LR -150X F
3" B A LL E YE
750-16 E
B IA S (4)
16"X 7"
(2)-6000lbs
8 LU G
7 LE A F
4 W IR E LO O M
TR LR -220X F
3" E YE
A D JU S TA B LE
S T235/85R 16E
R A D IA L(4)
16"X 7"
(2)-7000lbs
8 LU G
Q FLE X
4 W IR E LO O M
TR LR -300X F
3" E YE
A D JU S TA B LE
S T235/85R 16E
R A D IA L(6)
16"X 7"
(2)-6000lbs
8 LU G
Q FLE X
4 W IR E LO O M
TR LR -400X F
3" E YE
A D JU S TA B LE
S T235/85R 16E
R A D IA L(6)
16"X 7"
(3)-7000lbs.
8 LU G
Q FLE X
4 W IR E LO O M
TR LR -600X F
5TH W H E E L
S T215/75R 17.5H
R A D IA L (8)
16"X 7"
(3)-10000lbs
8 LU G
7 LE A F
6 W IR E LO O M
TR LR -800A R
5TH W H E E L
S T215/75R 17.5H
R A D IA L (8)
16"X 7"
(3)-10000lbs
8 LU G
A IR -R ID E
6 W IR E LO O M
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 13
DCA-10SPX3 — TRAILER SAFETY GUIDELINES
Tires/Wheels/Lug Nuts
Tires and wheels are a very important and critical
components of the trailer. When specifying or replacing the
trailer wheels it is important the wheels, tires, and axle are
properly matched.
CAUTION:
DO NOT attempt to repair or modify a
wheel. DO NOT install in inner tube to
correct a leak through the rim. If the rim
is cracked,
the
air
pressure in
the inner tube may cause pieces
of the rim to explode (break off)
with great force and cause serious
eye or bodily injury.
Tire Wear/Inflation
Tire inflation pressure is the most important factor in tire life.
Pressure should be checked cold before operation DO NOT
bleed air from tires when they are hot. Check inflation
pressure weekly during use to insure the maximum tire life
and tread wear.
Table 2 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
Suspension
The leaf suspension springs and associated components
(Figure 2) should be visually inspected every 6,000 miles for
signs of excessive wear, elongation of bolt holes, and
loosening of fasteners. Replace all damaged parts
(suspension) immediately. Torqued suspension components
as detailed in Table 3.
CAUTION:
NOTE
Figure 2. Major Suspension Components
ALWAYS wear safety glasses when removing
or installing force fitted parts. Failure to
comply may result in serious injury.
PAGE 14 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — TRAILER SAFETY GUIDELINES
Table 3. Suspension Torque Requirements
Item
Torque (Ft.-Lbs.)
3/8" U-BOLT
MIN-30 MAX-35
7/16" U-BOLT
MIN-45 MAX-60
1/2" U-BOLT
MIN-45 MAX-60
SHACKLE BOLT
SNUG FIT ONLY. PARTS MUST ROTATE FREELY.
SPRING EYE BOLT
LOCKING NUTS OR COTTER PINS ARE PROVIDED TO
RETAIN NUT-BOLT ASSEMBLY.
MIN-30 MAX-50
SHOULDER TYPE
SHACKLE BOLT
Lug Nut Torque Requirements
It is extremely important to apply and maintain proper wheel
mounting torque on the trailer. Be sure to use only the
fasteners matched to the cone angle of the wheel. Proper
procedure for attachment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
2. Torque all lug nuts in sequence. See Figure 3. DO NOT
torque the wheel lug nuts all the way down. Tighten
each lug nut in 3 separate passes as defined by Table 4.
3. After first road use, retorque all lug nuts in sequence.
Check all wheel lug nuts periodically.
Table 4. Tire Torque Requirements
Wheel Size
First Pass
FT-LBS
Second Pass
FT-LBS
Third Pass
FT-LBS
12"
20-25
35-40
50-65
13"
20-25
35-40
50-65
14"
20-25
50-60
90-120
15"
20-25
50-60
90-120
16"
20-25
50-60
90-120
Figure 3. Wheel Lug Nuts Tightening Sequence
NOTE
NEVER use an pneumatic air gun to
tighten wheel lug nuts.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 15
DCA-10SPX3 —TRAILER-WIRING DIAGRAM
NOTE:
LIGHTS ARE ORIENTED FROM THE DRIVER’S SEAT
PAGE 16 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 —OPERATION AND SAFETY DECALS
Machine Safety Decals
The DCA10SPX3 generator is equipped with a number of safety decals. These decals are provided for operator safety and
maintenance information. The illustration below and on the preceding pages show these decals as they appear on the machine.
Should any of these decals become unreadable, replacements can be obtained from your dealer.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 17
DCA-10SPX3 —OPERATION AND SAFETY DECALS
Machine Safety Decals
PAGE 18 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — SPECIFICATIONS
Table 5. Specifications
Generator Specifications
Model
DCA10SPX3
Type
Rotating-Field, Protection Type Synchronous Generator
Excitation
Brushless Type (With A.V.R)
Phase
Single Phase
Frequency
60 Hz
Wires
3-Wires (Neutral Grounded)
10.5 kW/16.5 HP
Max. Rated Output
@ 1800 rpm
10 kW/16.5 HP
Continious Rated Output
@ 1800 rpm
Single Phase Output Voltage
120/240 Volts
Frequency
60 Hz
Power Factor
100%
Rating
Continuous
Engine Specifications
Model
KUBOTA D1403
Type
Vertical, 3-Cycle
No. of Cylinders
3
Displacement
1393 cu. in.
Bore X Stroke
3.15 in. X 3.64 in.
(80 mm X 92.4 mm)
Cooling System
Water-Cooled
Starting System
Electric Start
Cooling Water Capacity
1.4 gal/5.3 liters
Lube Oil Capacity
1.77 gal/6.7 liters
Lubricant (API Class)
Above CC Grade
Battery
12V-70Ah
Fuel
Diesel Fuel Oil No. 2-D
At full load 1.1 gal/hr./ 4.2 liters/hr.
Fuel Consumption
At 3/4 load 0.9 gal/hr./ 3.4 liters/hr.
At 1/2 load 0.7 gal/hr./ 2.6 liters/hr.
At 1/2 load 0.5 gal/hr./ 1.9 liters/hr.
Sound At Full Load
65 dbA (distance = 23 feet)
Dimensions (LxWxH)
56 x 26 x 36 in.
(142 x 66 x 91 cm.)
Dry Weight
1123 lbs. (509 kg)
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 19
DCA-10SPX3 — GENERAL INFORMATION
DCA-10SPX3 3 FAMILIARIZATION
Generator
The MQ Power Model DCA-10SPX3 is a 10 kW generator
that is designed as a high quality portable (requires a trailer
for transport) power source for telecom sites, lighting
facilities, power tools, submersible pumps and other
industrial and construction machinery.
Control Panel
The control panel is provided with the following:
 One GFCI 120 volt receptacle, 20 amp (single-phase)
 10 kW Output Terminal (UNV)
 Main Circuit Breaker 45 amps
 GFCI Circuit Breaker 20 amps
 AC Ammeter
 AC Voltmeter
 Output Voltage Adjustment
 Ignition Switch
 Water Temperature Gauge
 Oil Pressure Gauge
 Warning Indicator
 Frequency Meter (Hz)
 Hour Meter
 Ground Terminal
Open Delta Excitation System
The DCA-10SPX3 generator is equipped with the state of
the art "Open-Delta" excitation system. The open delta
system consist of an electrically independent winding wound
among stationary windings of the AC output section.
There are four Leads: A, B, C and D. During light loads, the
power to the Automatic Voltage Regulator (AVR) is supplied
from the leads of B & C, when loads increase, the AVR
switches and accepts power from leads A & D. The output
of leads A & D increase proportionally with load. This has
the effect of adding the voltages of each phase to provide
better voltage response during heavy loads.
The connections of the AVR to the AC output windings are
for the sole purpose of sensing only. No power is required
from these windings.
The open-delta design provides virtually unlimited excitation
current due to its independent power supply offering
maximum motor starting capabilities. The excitation does
not have a "fixed ceiling" and responds according the
demands of the required load.
Engine
The DCA-10SPX3 is powered by a 3-cylinder KUBOTA Model
D1403 diesel engine. This engine is designed to meet every
performance requirement for the generator. Reference Table
5, page 19 for engine specifications.
In keeping with MQ Power's policy of constantly improving
its products, the specifications quoted herein are subject to
change without prior notice.
PAGE 20 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — MAJOR COMPONENTS
Figure 4. DCA10SPX3 Generator Major Components
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 21
DCA-10SPX3 — DIMENSIONS (TOP & SIDE)
Figure 5a. Dimensions (Top & Side)
PAGE 22 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — DIMENSIONS (FRONT, REAR & BOTTOM)
Figure 5b. Dimensions (Front, Rear)
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 23
DCA-10SPX3 — CONTROL PANEL, CONTROLS AND INDICATORS
Figure 6. Control Panel
PAGE 24 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — CONTROL PANEL, CONTROLS AND INDICATORS
The definitions below describe the controls and functions
of the DCA-10SPX3 (Figure 6):
1. Frequency Meter – Indicates the output frequency in
hertz (Hz). Normally 60 Hz ±1 Hz .
2. AC Ammeter – Indicates the amount of current the
load is being drawn from the generator.
3.
AC Voltmeter – Indicates the single phase output
voltage present at the UNV terminals.
4.
Engine Warning Display Module – This module
displays the following engine failures:
A. Overheat Lamp – This lamp goes ON
when the coolant is over 215oF. If the
lamp goes ON during normal operation
of the generator, the emergency shutdown device will stop the engine
automatically.
B. Low Oil Pressure Lamp – During
normal operation of the generator this
lamp should remain OFF. After the oil
pressure rises after start-up, the lamp
will go OFF. If this lamp is ever lit (ON)
during normal operation of the generator, the emergency
shut-down device will stop the engine automatically.
C. Low Fuel Level Lamp – When this lamp
is ON, it is time to stop the engine and
add fuel. Remember to let the engine cool
before adding fuel.
5.
Ignition Switch - This switch turns on and off the
engine with a key.
6.
Voltage Regulator Control – Allows manual
adjustment of the generator’s output voltage.
7.
Hour Meter - This meter monitors the number of hours
the generator has been running. Use this meter to
schedule regular maintenance.
8.
Oil Pressure Gauge – During normal operation this
gauge be should read in the “GREEN” zone. When
starting the generator, the oil pressure mark reads
higher, but after the engine warms up the oil pressure
should return to the green zone.
9.
Water Temperature Gauge – During normal operation
this gauge be should read in the “GREEN” zone.
10. A.C. GCFI Receptacle - This output receptacle is used
as a power source.
11. Ground Terminal - This is used to ground the
generator.
12. UNV Terminal - Used to connect AC load for 120V
or 240V single phase.
13. Main Circuit Breaker – This three-pole,20 amp main
breaker is provided to protect the UNV voltage output
terminals from overload.
14. GCFI Receptacle Circuit Breaker - This will shut down
the output receptacle if there in an overload.
D. Low Battery Fluid Lamp – This lamp
goes ON when the battery fluid is low. If
this lamp goes ON during normal operation
of the generator, stop the engine and fill
the battery with distilled water to the
specified level.
E. Clogged Air Filter Lamp – This lamp
goes ON when the air filter is clogged. If
this lamp goes ON during normal
operation of the generator, stop the
engine and replace the air filter.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 25
DCA10SPX3 OUTPUT TERMINAL
FIGURE 7. Output Terminal Panel
120 Volt Recetacle
One GFCI Duplex Nema 5-20R (120V, 20 Amp) receptacle
is provided on the output terminal. This receptacle can be
used anytime the generator is in operation. The receptacle
is controlled by the circuit breaker located on the control
panel.
FIGURE 8. Duplex Receptacle Detail
The reset button is for the GFCI when the circuit is tripped.
Pressing the "Test Button" (See Figure 9) in the center of
this receptacle will check the GFCI function. The receptacle
should be tested at least once a month.
Figure 9. GFCI Test Button
PAGE 26 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA10SP3X OUTPUT TERMINAL
Output Terminal Panel Available Voltages
The DCA10SPX3 is a single phase generator only. It is
able to supply both 120 volt and 240 volt.
Maximum Amps
The DCA-10SPX3 can provide 41.7 amps at 120 or 240
volts. Do not exceed the maximum amps!
120V Hard Wire Hookup
240V Hard Wire Hookup
The output terminal panel, when suppling single phase 120
volts, will provide two circuits available at 41.7 amps with
any two wires plus the ground. (See Figure 10 below.)
The output terminal panel, when suppling single phase 240
volts, will provide one circuit available at 41.7 amps with
two wires plus the ground. (See Figure 11 below.)
Figure 10. Hard Wire Hook-up
for 120 Volt
Figure 11. Hard Wire Hook-up
for 240 Volt
NOTE
When using plural single phase
voltages, make sure to balance
the load on each of the single
phase legs.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 27
DCA-10SPX3 — INSTALLATION
Outdoor Installation
Install the generator in a location where it is not exposed to
rain or sunshine. Make sure the generator is on a secure
level ground so that it cannot slide or shift around. Also
install the generator in a manner so the exhaust will not be
discharged in the direction of nearby homes.
The installation site must be away from excessive moisture
and dust. All electrical equipment should be protected from
excessive moisture. Failure to do will result in deterioration
of the insulation and will result in short circuits and grounding.
Foreign materials such as dust, sand, lint and abrasive
materials cause excessive wear, to the engine parts and
the alternator parts.
CAUTION :
Pay close attention to ventilation when
operating the generator inside tunnels and
caves. The engine exhaust contains
noxious elements. Engine exhaust must
be routed to a ventilated area.
Indoor Installation
Exhaust gases from diesel engines are extremely poisonous.
Whenever an engine is installed indoors the exhaust fumes
must be vented to the outside. The engine should be installed
at least two feet from any outside wall. Using an exhaust
pipe which is too long or too small can cause excessive
back pressure which will cause the engine to overheat.
CAUTION :
An electric shock is apt to happen when
vibrators are used. Pay close attention
to handling when operating vibrators and
always use rubber boots and gloves to
protect the body from electrical shock.
Generator Grounding
To prevent electrical shock and possible damage to the
equipment, it is important to provide a good EARTH ground.
Article 250 (Grounding) of the National Electrical Code (NEC)
provides guide lines for proper grounding and specifies that
the cable ground shall be connected to the grounding system
of the building as close to the point of cable entry as
practical.
NEC articles 250-64(b) and 250-66 set the following
grounding requirements:
1. Use one of the following wire types to connect the
generator to earth ground.
a. Copper - 10 AWG (5.3 mm2) or larger.
b. Aluminum - 8 AWG (8.4 mm2) or larger.
2. When grounding the generator (Figure 12) connect the
ground cable between the lock washer and the nut on
the generator and tighten the nut fully. Connect the other
end of the ground cable to earth ground.
3. NEC article 250-52(c) specifies that the earth ground
rod should be buried a minimum of 8 ft. into the ground.
NOTE
Eliminate the danger of deadly carbon monoxide gas.
Remember that exhaust fumes from any diesel engine are
very poisonous if discharged in a closed room, but harmless
if allowed to mix with the outside air. If the generator is
installed indoors, you must make provisions from venting
the engine exhaust to the outside of the building.
DO NOT cover ventilation areas on the enclosure. Covering
the ventilation grids will cause the engine to overheat.
When connecting the generator to
any buildings electrical system
ALWAYS consult with a licensed
electrician.
PAGE 28 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — INSTALLATION
Figure 12.
Typical Generator Grounding Application
CAUTION :
Always check local codes for
proper grounding codes and
laws.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 29
DCA-10SPX3 — PRE-SETUP
General Inspection Prior to Operation
Circuit Breaker
The DCA-10SPX3 generator has been thoroughly inspected
and accepted prior to shipment from the factory. However,
be sure to check for damaged parts or components, or loose
nuts and bolts, which could have occurred in transit.
Extension Cable
When electric power is to provided to loads (ie. power
tools) at a distance from the generator, extension cables
are used. Cables should be sized to allow for distance in
length and amperage so that the voltage drop between
the generator and point of use (load) is held to a minimum.
Use Table 6 (cable selection guide) as a guide for selecting
proper cable size.
To protect the generator from an overload, a 3-pole, 50 amp,
main circuit breaker is provided to protect the UNV output
from overload. In addition a 2-pole, 20 amp GFCI circuit
breaker is provided to protect the GFCI receptacle from
overload. Make sure to switch both circuit breakers to the
"OFF" position prior to starting the engine.
NOTE
ALWAYS consult with a licensed
electrician for correct extension
cord wire size.
Table 6. Cable Selection (60 Hz, Single Phase Operation)
Load In Watts
Current in
Amperes At 120 At 240
Volts
Volts
Maximum Allowable Cable Length
#10 Wire
#12 Wire
#14 Wire
#16 Wire
2.5
300
600
1000 ft.
600 ft.
375 ft.
250 ft.
5
600
1200
500 ft.
300 ft.
200 ft.
125 ft.
7.5
900
1800
350 ft.
200 ft.
125 ft.
100 ft.
10
1200
2400
250 ft.
150 ft.
100 ft.
15
1800
3600
150 ft.
100 ft.
65 ft.
20
2400
4800
125 ft.
75 ft.
50 ft.
CAUTION: Equipment damage can result from low voltage.
PAGE 30 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — PRE-SETUP
Lubrication Oil
Fuel
Fill the engine crankcase with lubricating oil through the filler
hole, but do not overfill. Make sure the generator is level.
With the dipstick inserted all the way, but without being screw
into the filler hole, verify that the oil level is maintained
between the two notches (Figure 13) on the dipstick. See
Table 7 for proper selection of engine oil.
Fill the fuel tank with clean and fresh diesel fuel. DO NOT
fill the tank beyond capacity.
Pay attention to the fuel tank capacity when replenishing
fuel. Refer to the fuel tank capacity listed on page 19
Specification Table 5.
The fuel tank cap must be closed tightly after filling. Handle
fuel in a safety container. If the container does not have a
spout, use a funnel. Wipe up any spilled fuel immediately.
CAUTION :
Never fill the fuel tank while the engine is
running or in the dark. Gasoline spillage
on a hot engine can cause a fire or
explosion. If gasoline spillage occurs, wipe
up the spilled gasoline completely to
prevent fire hazards.
Coolant
Use only drinkable tap water. If hard water or water with
many impurities is used, the inside of the engine and radiator
may become coated with deposits and cooling efficiency
will be reduced. See maintenance section on page 36 and
37 on instructions to flush out radiator.
Figure 13. Engine Oil Dipstick
When checking the engine oil, be sure to check if the oil is
clean and viscous. If the oil is dirty, drain the oil by removing
the oil drain plug, and refill with the specified amount of oil
as outlined in the Kubota Engine Owner's Manual.
An anticorrosion additive added to the water will help prevent
deposits and corrosion in the cooling system.
Table 7. Recommended Motor Oil
Temperature Range
Type Oil
104° F ~ 23° F
(40° C ~ -5°C)
SAE 30
23° F ~ 5° F
(-5° C ~ -15°C)
SAE 20 or SAE 10W-30
Below 5° C (-15°)
SAE 10W or SAE 10W-30
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 31
DCA-10SPX3 — PRE-SETUP
CAUTION :
When adding coolant or antifreeze to the
radiator, do not remove the radiator cap
until the unit has completely cooled.
Day-to-day addition of coolant is done from the reserve tank.
When adding coolant to the radiator, DO NOT remove the
radiator cap until the unit has completely cooled. See Table
8. for engine, radiator, and reserve tank coolant capacities.
Make sure the coolant level in the reserve tank is always
between the "H" and the "L" markings.
Table 8. Coolant Capacity
Engine and Radiator
1.3 Gal. (4.9L)
Reserve Tank
0.27 Gal. (1L)
Cleaning the Outer Radiator
The engine may overheat if the radiator fins become
overloaded with dust or debris. Periodically clean the radiator
fins with compressed air. Cleaning inside the radiator is
dangerous, so clean only with the engine turned off and the
battery disconnected.
Air Cleaner
Periodic cleaning/replacement is necessary. Inspect it in
accordance with the Kubota Engine Owner's Manual.
Fan Belt Tension
A slack fan belt may contribute to overheating, or to
insufficient charging of the battery. Inspect the fan belt for
damage and wear and adjust it in accordance with the Kubota
Engine Owner's Manual.
The fan belt tension is proper if the fan belt bends 10 to 15
mm (Figure 14) when depressed with the thumb as shown
below. Never place hands near the belts or fan while the
generator is running.
Operation in Freezing Weather
When operating in freezing weather, be certain the proper
amount
of antifreeze
9) hasisbeen
Day-to-day
addition (Table
of coolant
doneadded.
from the
Table 9. Anti-Freeze Operating Temperatures
Figure 14. Fan Belt Tension
Freezing Point
Boiling Point
°C
°F
°C
°F
-24
-12
106
222
Vol %
Anti-Freeze
40
50
-37
-34
108
226
NOTE
When the antifreeze is mixed with
water, the antifreeze mixing ratio must
be less than 50%.
CAUTION :
Never place hands near the belts or fan
while the generator set is running.
Adjusting Fan Belt
If the fan belt does not have the 10 to 15mm defection,
follow the procedure below to adjust:
 Loosesn the alternator adjusting plate and alternator
mounding bolt.
 Pivot the alternator at the mounting bolt toward the engine
left or right until the belt reflects the proper tension.
 Tighten the mounting bolt and the adjusting bolt.
PAGE 32 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — PRE-SETUP
Battery
This unit is of negative ground. DO NOT connect in reverse.
Always maintain battery fluid level between the specified
marks. Battery life will be shortened, if the fluid level is not
properly maintained. Add only distilled water when
replenishment is necessary. DO NOT over fill.
The battery is sufficiently charged if the specific gravity of
the battery fluid is 1.28 (at 68° F). If the specific gravity
should fall to 1.245 or lower, it indicates that the battery is
dead and needs to be recharged or replaced.
Check to see whether the battery cables are loose. Poor
contact may result in poor starting or malfunctions. Always
keep the terminals firmly tightened. Coating the terminals
with a thin film of grease will help to inhibit corrosion.
Battery Cable Installation
ALWAYS be sure the battery cables (Figure 15) are properly
connected to the battery terminals as shown below. The RED
cable is connected to the positive terminal of the battery,
and the BLACK cable is connected to the negative terminal
of the battery.
CAUTION :
If the battery cable is connected
incorrectly, damage to the generator will
occur. Pay close attention to the polarity
of the battery when connecting the
battery.
When connecting battery do the following:
1. DO NOT connect the battery cables to the battery
terminals when the key is in the ignition and is set in
'START' mode. ALWAYS remove the key from the
ignition and the ignition switch is in the OFF position
when connecting the battery.
2. Place a small amount of grease around both battery
terminals. This will ensure a good connection and will
help prevent corrosion around the battery terminals.
CAUTION :
Inadequate battery connections may
cause poor starting of the generator, and
create other malfunctions.
Wiring
Inspect the entire generator for bad or worn electrical wiring
or connections. If any wiring or connections are exposed
(insulation missing) replace wiring immediately.
Piping and Hose Connection
Inspect all piping, oil hose, and fuel hose connections for
wear and tightness. Tighten all hose clamps and check hoses
for leaks.
Figure 15. Battery Connections
If any hose (fuel or oil) lines are defective replace them
immediately.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 33
DCA-10SPX3 — LOAD APPLICATION
Single Phase, Load
Always be sure to check the nameplate on the generator
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generator for operating the equipment.
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
NOTE
If wattage is not given on the
equipment's name plate, approximate
wattage may be determined by
multiplying nameplate voltage by the
nameplate amperage.
WATTS = VOLTAGE x AMPERAGE
An inadequate size connecting cable which cannot carry
the required load can cause a voltage drop which can burn
out the appliance or tool and overheat the cable.
● When connecting a resistance load such as an
incandescent lamp or electric heater, a capacity of up
to the generating set’s rated output (kW) can be used.
● When connecting a fluorescent or mercury lamp, a
capacity of up to the generating set’s rated output (kW)
multiplied by 0.6 can be used.
● When connecting an electric drill or other power tools,
pay close attention to the required starting current
capacity.
The power factor of this generator is 1.0. See Table 10.
below when connecting loads.
Table 10. Power Factor By Load
Type Of Load
Power Factor
Single-phase induction motors
0.4 - 0.75
Electric heaters, incandescent
lamps
1.0
Fluorescent lamps, mercury lamps
0.4 - 0.9
Electronic devices, communication
equipment
1.0
CAUTION:
Motors and motor-driven equipment draw
much greater current for starting than during
operation.
When connecting ordinary power tools, a capacity of up to
the generating set’s rated output (kW) multiplied by 0.8 can
be used.
PAGE 34 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — GENERATOR START-UP PROCEDURE
WARNING:
The engine's exhaust contains harmful
emissions. ALWAYS ventilate the
exhaust when operating inside tunnels,
excavations or buildings. Direct exhaust
away from nearby personnel.
2. Connect the load to the UNV terminals as shown in
Figure 17. These terminals can be found on the front of
the generator by lifting the UNV lug cover. It may be
necessary to remove the retaining lug that secures the
cover. Make sure to tighten terminal nuts securely to
prevent load wires from slipping out.
Before Starting
Engine
1. Check the lubricating oil level prior to starting the engine.
Make sure the generator is level. The oil level must be
maintained between two notches on the dipstick.
2. When there is not enough lubricating oil, fill the crankcase
with high grade motor oil. Use a high quality detergent
oil classified CC or higher (See Table 7 on page 29).
3. Check the coolant level in the radiator and subtank.
Replenish with antifreeze as necessary. Always maintain
the coolant level between the FULL and LOW markings
on the coolant container. Be sure that the radiator cap is
fastened securely.
4. Check the fuel level on the fuel gauge. If fuel is low, fill
the fuel tank with clean fresh unleaded automotive diesel
fuel. If fuel spillage occurs, completely wipe up the spilled
fuel immediately.
Figure 17. UNV Terminal Lugs (Load)
3. After attaching the load wires to the AC output terminals,
secure the UNV cover by inserting the retaining screw
(Figure 18) back into the cover.
Before Starting
Generator and Control Panel
CAUTION:
NEVER start the engine with the main
or GFCI circuit breakers in the ON
position.
1. Be sure to disconnect the electrical load and switch the
main and G.F.C.I. circuit breakers (Figure 16) to the
“OFF” position prior to starting the engine.
Figure 18. UNV Lug Cover
CIRCUIT BREAKER CIRCUIT BREAKER
GFCI RECEPTACLE
MAIN
OFF
OFF
Figure 16. Main and GFCI Circuit Breakers
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 35
DCA-10SPX3 — GENERATOR START-UP PROCEDURE
4. Connect the negative battery cable (BLACK) to the
negative post on the battery (Figure 19).
7. The ammeter (Figure 23) will indicate zero amps with
no load applied. When a load is applied, this meter will
indicate the amount of current that the load is drawing
from the generator.
20
40
0
IVE
ST
PO
E
TIV
GA
NE
RY
E
TT
A
B
Figure 19. Battery Connections
5. Close all engine enclosure doors (Figure 20).
60
75
A
Figure 23. Ammeter (No Load)
8. The engine oil pressure gauge (Figure 24) will indicate
the oil pressure (kg/ cm2) of the engine. Under normal
operating conditions the oil pressure is approximately
25 psi.
Figure 24. Oil Pressure Gauge
Figure 20. Engine Enclosure Doors
6. Before starting the generator, turn the key to preheat
(Figure 21) until the warning indicator light turns off.
Then turn the key to the right to 'Start'(Figure 22). Once
the engine starts, release the key.
9. The water temperature gauge (Figure 25) will indicate
the coolant temperature. Under normal operating
conditions the coolant temperature is between 165 and
215 degrees fahrenheit.
Figure 25. Coolant Temperature Gauge
Figure 21. Ignition Switch (Preheat)
Figure 22. Ignition Switch (Start)
PAGE 36 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — GENERATOR SHUT-DOWN PROCEDURE
10. The battery voltage gauge (Figure 26) will indicate the
voltage of the battery when the generator is operating.
Under normal operating conditions this voltage is
between 11.2 and 15.2 volts.
Engine Shutdown
To shutdown the generator use the following procedure:
1. Place both the MAIN and GFCI circuit breakers to the
"OFF position" (Figure 29).
CIRCUIT BREAKER
MAIN
OFF
Figure 26. Battery Voltage Gauge
11. If there are no abnormal problems shown on the MPEC
LED display, turn both the MAIN and GFCI circuit
breakers to their ON position (Figure 27).
CIRCUIT BREAKER
MAIN
CIRCUIT BREAKER
GFCI RECEPTACLE
OFF
Figure 29. GFCI and Main Circuit Breaker
(OFF)
2. Let the engine cool by running 3-5 minutes with no load
applied.
3. Turn the key to the 'STOP' position to shut down the
engine (Figure 30).
CIRCUIT BREAKER
GFI RECEPTACLE
ON
ON
Figure 27. Main and GFCI Circuit Breakers
Figure 30. Ignition Switch (OFF)
12. Observe at the generator's ammeter (Figure 28) and
verify that it reads the anticipated amount of current
with respect to the load. The ammeter will only display a
current reading if the load is in use.
20
40
0
60
75
A
Figure 28. Ammeter (Load)
13. The generator will run until manually stopped or an
abnormal condition occurs.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 37
DCA-10SPX3 — MAINTENANCE
General Inspection
Check Oil Level
Prior to each use, the generator should be cleaned and
inspected for deficiencies. Check for loose, missing or
damaged nuts, bolts or other fasteners. Also check for fuel,
oil, and coolant leaks.
Check the crankcase oil level prior to each use, or when
the fuel tank is filled. Insufficient oil may cause severe
damage to the engine. Make sure the generator is level.
The oil level must be between the two notches on the dipstick
as shown in Figure 8, page 29.
Engine Side (Refer to the Engine Instruction Manual)
Air Cleaner
Every 50 hours: Remove air cleaner element and clean heavy
duty paper element with kerosene, or foam element with
liquid detergent and hot water. Wrap foam element in a cloth
and squeeze dry. For heavy duty paper element, wipe
excess kerosene with towel.
Fuel Addition
Replacing Oil Filter
 Detach the oil filter cartridge with a filter wrench.
 Apply a film of oil to the gasket for the cartridge.
 Screw in the cartridge by hand. When the gasket is in
contact with the seal surface, tighten the cartridge one
or two more times by hand.
Add diesel fuel (the grade may vary according to season
and locations). Always pour through the mesh filter.
 After the oil cartridge has been replaced, the engine oil
will drop slightly. Run the engine for a while and check
for leaks before adding more oil if needed. Clean
excessive oil from engine.
Removing Water from the Fuel Tank
Replacing Fuel Filter
After prolonged use, water and other impurities accumulate
in the bottom of the tank. Occasionally remove the drain
cock and drain the contents. During cold weather, the more
empty volume inside the tank, the easier it is for water to
condense. This can be reduced by keeping the tank full as
much as possible.
 Replace the fuel filter cartridge with new one every 400
hours or so.
 Apply fuel oil thinly over the gasket and hand-tighten
the cartridge into position.
 Vent any air.
Flushing Out Radiator and Replacing Coolant
Air Removal
If air enters the fuel injection system of a diesel engine,
starting becomes impossible. After running out of fuel, or
after disassembling the fuel system, bleed the system
according to the following procedure.
To restart after running out of fuel, turn the switch to the
“ON” position for 15-30 seconds. Try again, if needed. This
unit is equipped with an automatic air bleeding system.
Service Daily
If the engine is operating in very dusty or dry grass
conditions, a clogged air cleaner will result. This can lead to
a loss of power, excessive carbon buildup in the combustion
chamber in high fuel consumption.
Cleaning the Fuel Strainer
Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in gasoline.
Securely fasten the fuel strainer cap so that fuel will not
leak. Check the fuel strainer every 200 hours of operation or
once a month.
 Open both cocks located at the crankcase side and at
the lower part of the radiator and drain coolant. Open
the radiator cap while draining. Remove the overflow
tank and drain.
 Check hoses for softening and kinks. Check clamps
for signs of leakage.
 Flush the radiator by running clean tap water through
radiator until signs of rust and dirt are removed. DO
NOT clean radiator core with any objects, such as a
screwdriver.
 Tighten both cocks and replace the overflow tank.
 Replace with coolant (see page 30, Table 5 for mixture).
 Close radiator cap tightly.
CAUTION :
Allow engine to cool when flushing out
radiator. Flushing the radiator while hot
will damage radiator.
PAGE 38 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — MAINTENANCE
Generator Storage
For storage of the generator for over 30 days, the following
is required:
 Fill the fuel tank completely.
 Completely drain the oil from the crankcase and refill
with fresh oil.
 Clean all external parts of the generator with a cloth.
 Cover the generating set and store in a clean, dry place.
INSPECTION / MAINTENANCE
10 Hrs
DAILY
Check Engine Fluid Levels
X
Check Air Cleaner
X
Check Battery Acid Level
X
Check Fan Belt Condition
X
Check for Leaks
X
Check for Loosening of Parts
Replace Engine Oil and Filter *
X
Clean Air Filter
X
Drain Bottom of Fuel Tank
X
Clean Unit, Inside and Outside
X
2
GENERATOR
500 Hrs
1000 Hrs
X
1
ENGINE
250 Hrs
Change Fuel Filter *
X
Clean Radiator and Check Coolant Protection
Level
X
Replace Air Filter Element
X
Change Corrosion Resistor
X
Check all Hoses and Clamps
X
Clean Inside of Fuel Tank
X
Measure Insulation Resistance Over 3M ohms
X
*1 Replace engine oil anf filter at 100 hours, first time only.
*2 Replace fuel filter at 250 Hours, first time only.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 39
DCA-10SPX3 —GENERATOR WIRING DIAGRAM
PAGE 40 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 —ENGINE WIRING DIAGRAM
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 41
DCA-10SPX3 — TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
diagnosis based on the Engine Troubleshooting (Table 11)
information shown below and on the proceeding page. If the
problem cannot be remedied, consult our company's
business office or service plant.
TABLE 11. ENGINE TROUBLESHOOTING
SYMPTOM
Engine does not start.
POSSIBLE PROBLEM
SOLUTION
No fuel?
Replenish fuel.
Air in the fuel system?
Bleed system.
Water in the fuel system?
Remove water from fuel tank.
Fuel pipe clogged?
Clean fuel pipe.
Fuel filter clogged?
Clean or change fuel filter.
Excessively high viscosity of fuel
or engine oil at low temperature?
Use the specified fuel or engine oil.
Fuel with low cetane number?
Use the specified fuel.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Incorrect injection timing?
Adjust.
Fuel cam shaft worn?
Replace.
Injection nozzle clogged?
Clean injection nozzle.
Injection pump malfunctioning?
Repair or replace.
Seizure of crankshaft, camshaft,
piston, cylinder liner or bearing?
Repair or replace.
Compression leak from cylinder?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
Improper valve timing?
Correct or replace timing gear.
Piston ring and liner worn?
Replace.
Excessive valve clearance?
Adjust.
Starter malfunctioning?
Repair or replace.
Wiring disconnected?
Connect wiring.
Starter does not run.
PAGE 42 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — TROUBLESHOOTING (ENGINE)
TABLE 11. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
Engine revolution is not
smooth.
Either white or blue
exhaust gas is observed.
Either black or dark gray
exhaust gas is observed.
Deficient output.
POSSIBLE PROBLEM
SOLUTION
Fuel filter clogged or dirty?
Clean or change.
Air cleaner clogged?
Clean or change.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Injection pump malfunctioning?
Repair or replace.
Incorrect nozzle opening
pressure?
Adjust.
Injection nozzle stuck or
clogged?
Repair or replace.
Fuel over flow pipe clogged?
Clean.
Governor malfunctioning?
Repair.
Excessive engine oil?
Reduce to the specified level.
Piston ring and liner worn or
stuck?
Repair or replace.
Incorrect injection timing?
Adjust.
Deficient compression?
Adjust top clearance.
Overload?
Lessen the load.
Low grade fuel used?
Use the specified fuel.
Fuel filter clogged?
Clean or change.
Air cleaner clogged?
Clean or change.
Deficient nozzle injection?
Repair or replace the nozzle.
Incorrect injection timing?
Adjust.
Engine's moving parts seem to
be seizing?
Repair or replace.
Uneven fuel injection?
Repair or replace the injection pump.
Deficient nozzle injection?
Repair or replace the nozzle.
Compression leak?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 43
DCA-10SPX3 — TROUBLESHOOTING (GENERATOR/ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
diagnosis based on the Generator Troubleshooting (Table 12)
information shown below and on the proceeding page. If the
problem cannot be remedied, consult our company's
business office or service plant.
TABLE 12. ENGINE & GENERATOR TROUBLESHOOTING
SYMPTOM
Engine fails to start and starter does
not rotate.
Engine fails to start and starter
rotates.
Engine starts and engine remains at
low speed.
Engine starts and engine speed rises
and no voltage is present in AC
power source.
Engine starts and engine speed rises
but AC power voltage is too low (or
too high) or cannot be used.
Engine starts and engine speed rises
but battery discharges excessively.
Engine starts and engine speed rises
and engine seems overloaded.
POSSIBLE PROBLEM
SOLUTION
Dead Battery?
Replace Battery.
Defective Starter Switch?
Replace Switch.
Defective Starter?
Replace Starter.
Fuse F5 Burned Out?
Replace Fuse.
Broken Pre-Heat Circuit?`
Check Pre-Heat Circuit.
No Fuel?
Add Fuel.
Defective Wiring?
Check Wiring.
Compression Leak?
Check/repair engine.
Air in the fuel system?
Repair or Bleed.
Clogged Fuel Strainer?
Clean or Replace.
Clogged Air Cleaner?
Clean or Replace.
Disconnected Wiring?
Check and Repair Wiring.
No Voltage Present in AC Power
source
Replace Rectifier (RE1).
Defective Rotor?
Replace Rotor.
Defective Automatic Voltage
Regulator?
Replace AVR.
Disconnected Wiring?
Check and Repair Wiring.
Layer Short-Circuit in armature
winding?
Replace Armature.
Defective Circuit Breaker (Protector)?
Replace Circuit Breaker (Protector).
Layer Short-Circuit, Broken Wires In
Armature Winding?
Repair or Replace Armature.
Voltage Regulator turned too low?
Adjust Voltage Regulator up.
Defective Engine Regulator?
Replace Regulator.
Defective Wiring?
Repair or Replace Wiring.
Defective Alternator?
Repair or Replace Alternator.
Damaged Alternator Bearing?
Replace Alternator Bearings.
PAGE 44 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
NOTE PAGE
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 45
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #, +, %, or
■, belong to the same assembly or kit.
*
Note: If more than one of the same reference number is listed,
the last one listed indicates newest (or latest) part available.
NOTE
The contents of this parts catalog are
subject to change without notice.
PAGE 46 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — SUGGESTED SPARE PARTS
DCA-10SPX3 W/KUBOTA D1403 DIESEL ENGINE 1 TO 3 UNITS
QTY. P/N
DESCRIPTION
1 ......... 0601820626 ..... AUTOMATIC VOLTAGE REGULATOR
1 ......... 0601807083 ..... MAIN CIRCUIT BREAKER
1 ......... 0601812597 ..... RECEPTACLE CIRCUIT BREAKER
1 ......... 0601840073 ..... VOLTAGE REGULATOR (RHEOSTAT)
3 ......... 1707972062 ..... OIL FILTER
1 ......... 0602122050 ..... OIL SENDING UNIT
1 ......... 0602123251 ..... WATER TEMPERATURE SENDING UNIT
1 ......... 1726697011 ..... FAN BELT
3 ......... 0602046372 ..... AIR FILTER
3 ......... 1522143172 ..... FUEL FILTER
1 ......... 0602100059 ..... STARTER SWITCH
3 ......... 3741055150 ..... KEY, STARTER SWITCH
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 47
DCA-10SPX3 — GENERATOR ASSY.
PAGE 48 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — GENERATOR ASSY.
GENERATOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
8321000102
71906308
7961025004
835161104
8351612004
8351615003
0601000209
0042610000
0105091025
0601822630
8001070003
0012108035
0042508000
0070506903
011208035
0016008045
0845041904
012010030
030210250
8401332004
10017106016
8351331004
8351512004
8351315003
8431350003
7561345403
0605000006
0010106030
952404470
0207010000
ROTOR ASS’Y
1
BEARING .................................................... 1 .............6308-DDU-C3
RECTIFIER
1
COUPLING DISK
2
WASHER, COUPLING HUB
1
BALANCING PLATE
2
BALANCING WEIGHT KIT
1
SPRING WASHER
4
HEX HEAD BOLT
4
SURGE ABSORBER ................................... 1 .............TNR23G471K
FAN
1
HEX HEAD BOLT
6
SPRING WASHER
3
BEARING .................................................... 1 .............6903- ZZ
HEX HEAD BOLT
6
HEX SOCKET HEAD CAP SCREW
3
GROMMET
1
HEX HEAD BOLT
6
SPRING WASHER
6
COVER, FAN
1
HEX HEAD BOLT
3
COVER, SUCTION
1
PACKING
1
END BRACKET
1
FIELD ASS’Y EXCITER
1
STATOR ASS’Y
1
RUBBER SUSPENSION
2
HEX HEAD BOLT
1
PLAIN WASHER
1
HEX NUT
2
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 49
DCA-10SPX3 — CONTROL PANEL ASSY.
CONTROL PANEL ASSY.
PAGE 50 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — CONTROL PANEL ASSY.
CONTROL PANEL ASSY.
NO.
PART NO.
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
B0225000003
0601800455
0601805745
0601800281
0601840073
0601840121
0601804715
3011816004
0027104020
0207004000
0602100059
0601813255
0601810830
0601800682
0602123085
0602123088
0602123251
0603306840
0602122035
0602122038
0602122050
0021806030
0601807083
0021004060
0040004000
0041204000
0601801123
0027106016
0601842304
0027104010
0601820626
0017105016
0601820038
0027104020
0601815759
0027104025
0602200474
0021005045
0040005000
0041205000
8701899004
0601806642
0601806644
0601806644
0027105016
0602201273
0602202566
0017105016
0601806640
0601842389
QTY.
REMARKS
CONTROL PANEL
1
FREQUENCY METER .......................................... 1 ............ FCF5 240V 45~65Hz
AC AMMETER ....................................................... 1 ............ ACF5 0~75A
AC VOLTMETER ................................................... 1 ............ SCF5 0~150V 0~300
RHEOSTAT (VOLTAGE REGULATOR) ............... 1 ............ RA20A2SE102BJ 2W 1K OHM
KNOB
1
CIRCUIT BREAKER .............................................. 1 ............ KM51 20A
BRACKET, CIRCUIT BREAKER
1
MACHINE SCREW
2
HEX. NUT
2
STARTER SWITCH .............................................. 1 ............ 3741059113
INDICATOR ASSY. ................................................ 1 ............ BL61160150
BULB
4
HOUR METER ...................................................... 1 ............ 82014
WATER TEMPERATURE GAUGE;1005752201 .. 1 ............ S/N4784541 TO S/N5180943
WATER TEMPERATURE GAUGE;1005752780 .. 1 ............ S/N5180944~
SENDER, WATER TEMPERATURE ..................... 1 ............ 0715001840
BUSHING
1
OIL PRESSURE GAUGE;1005760300 ................ 1 ............
S/N4784541 TO S/N5180943
OIL PRESSURE GAUGE;1005760450 ................ 1 ............ S/N5180944~
SENDER, OIL PRESSURE ................................... 1 ............ 0716000750
MACHINE SCREW
4
CIRCUIT BREAKER .............................................. 1 ............ XE50NS 45A
MACHINE SCREW
2
LOCK WASHER
2
PLAIN WASHER
2
CURRENT TRANSFORMER, AMMETER ........... 1 ............ COC3 150/5A
MACHINE SCREW
2
RESISTOR ............................................................ 1 ............ GG20W50 OHM
MACHINE SCREW
2
AUTOMATIC VOLTAGE REGULATOR ................ 1 ............ NTA4A2S
HEX. HEAD BOLT
4
RECTIFIER ........................................................... 1 ............ S15VB60
MACHINE SCREW
1
TEMINAL BOARD ................................................. 1 ............ KT206P
MACHINE SCREW
2
EMERGENCY UNIT .............................................. 1 ............ 1714760602
MACHINE SCREW
2
LOCK WASHER
2
PLAIN WASHER
2
FUSE BOX ............................................................. 1 ............ FB6PS
FUSE ..................................................................... 4 ............ 5A
FUSE ..................................................................... 2 ............ 15A
FUSE ..................................................................... 2 ............ 30A
MACHINE SCREW
2
TIMER ................................................................... 1 ............ 1569465992
RELAY ................................................................... 1 ............ 6888153542
HEX. HEAD BOLT
2
FUSE ..................................................................... 1 ............ 65A
RESISTOR ............................................................ 1 ............ 8.2 OHM 1/2W
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 51
DCA-10SPX3 — OUTPUT TERMINAL ASSY.
PAGE 52 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — OUTPUT TERMINAL ASSY.
OUTPUT TERMINAL ASSY.
NO.
PART NO.
PART NAME
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
15
17
18
19
0017106016
7561861003
0805088004
0821800014
014208020
0040008000
0041408000
1621849004
0039508000
020108060
0601815109
011206020
0207006000
0017105025
7831860104
7561860104
0027104016
0030004000
061812597
HEX HEAD BOLT
COVER, OUTPUT TERMINAL
STAY RUBBER
COLLAR
HEX HEAD BOLT
LOCK WASHER
PLAIN WASHER
OUTPUT TERMINAL
HEX NUT
HEX NUT
GROUND TERMINAL
HEX HEAD BOLT
HEX NUT
HEX HEAD BOLT
RUBBER SEAL
SET BOARD, OUTPUT TERMINAL
MACHINE SCREW
HEX NUT
RECEPTACLE
QTY.
REMARKS
1
2
1
2
3
8
8
3
3
3
1
2
1
4
1
1
2
2
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 53
DCA-10SPX3 — ENGINE & RADIATOR ASSY.
PAGE 54 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — ENGINE & RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
0805096804
HOSE BAND
1
2
0605515094
HOSE BAND
3
3
0802081104
CAP, RESERVE TANK
1
4
7222016304
HOSE BAND
1
5
0802081403
RESERVE TANK
1
6
1707611010
AIR CLEANER ............................................. 1
7
8322031004
BRACKET, AIR CLEANER
1
8
011008020
HEX. HEAD BOLT
6
9
3426013960
BAND, AIR CLEANER ................................. 1
10
011208030
HEX. HEAD BOLT
2
11
011006010
HEX. HEAD BOLT
4
12
0602011974
RADIATOR ................................................... 1
13
0017106016
HEX. HEAD BOLT
4
13
0017106016
HEX. HEAD BOLT
6
14
8325127605
BRACKET, FAN GUARD
1
15
7562012004
BRACKET, RADIATOR
2
16
0605515014
HOSE BAND
4
17
165717820171
DRAIN HOSE .............................................. 1
18
0017106035
HEX. HEAD BOLT
1
19
0605515001
HOSE BAND
3
20
1546173340
HOSE .......................................................... 1
21
8325127113
FAN GUARD
1
22
012212025
HEX. HEAD BOLT
7
23
0012410025
HEX. HEAD BOLT
1
24
8325112014
ENGINE FOOT
1
25
7000032091
CARTRIDGE, OIL FILTER ........................... 1
26
0017106016
HEX. HEAD BOLT
4
27
1502025004
DRAIN JOINT
1
28
0602021193
PACKING ..................................................... 1
29
0192200380
DRAIN HOSE
1
30
0605515003
HOSE BAND
2
31
0602022738
HOSE JOINT ................................................ 1
32
0131506000
NIPPLE, 1/2" ................................................ 1
33
B0322300004
DRAIN JOINT
1
34
0132006000
PLUG, 1/2" .................................................. 1
35
0802011104
PLUG
1
36
0150000018
O RING ........................................................ 1
37
1502025103C
DRAIN JOINT
1
38
1510872870
HOSE BAND ............................................... 4
39
1706372940
RADIATOR HOSE, UPPER ......................... 1
40
8322036103
HOSE, AIR CLEANER
1
41
8432036103
HOSE, AIR CLEANER
1
42
8325127504
BRACKET, FAN GUARD
1
43
7560150404
ENGINE ....................................................... 1 ............ KUBOTA D1403
44
0602014475
RADIATOR HOSE, LOWER ......................... 1 ............ KUBOTA 15461-72851
45
0207010000
HEX. NUT
2
46
8325112114
ENGINE FOOT
1
47
7605419004
RUBBER SUSPENSION
2
48
0603325011
VALVE ......................................................... 1 ............ BBS1/2
49
0602046335
ELEMENT, AIR CLEANER .......................... 1 ............ 113043002
50
8432036103
HOSE, AIR CLEANER
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 55
DCA-10SPX3 — BATTERY ASSY.
BATTERY
ASSY.
PAGE 56 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — BATTERY ASSY.
BATTERY ASSY.
NO. PART NO.
PART NAME
1
2
BATTERY .................. 1 ...... 65D31R
BATTERY FRAME 1
LINING
1
HEX HEAD BOLT
5
BATTERY SHEET 1
BATTERY BAND
1
BATTERY BOLT
1
HEX HEAD BOLT
2
BATTERY BOLT
1
WING NUT
2
LOCK WASHER
2
PLAIN WASHER
2
BATTERY CABLE
1
BATTERY CABLE
1
EARTH CABLE
1
TERMINAL ASS’Y. .... 1 ...... NO.9P
TERMINAL ASS’Y. .... 1 ...... NO.9N
TERMINAL CAP ........ 1 ...... 7C7R
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
0167306531
8452250003
8345967004
0017106016
7612251004
8432255024
8432256024
0017106016
8432256104
0037806000
0040006000
952404470
N012CABLE10SPX3
N013CABLE10SPX3
EARTH10SPX3
0602220310
0602220311
0602220600
QTY.
REMARKS
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 57
DCA-10SPX3 — MUFFLER ASSY.
PAGE 58 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — MUFFLER ASSY.
MUFFLER ASSY.
NO.
PART NO.
PART NAME
1
2
3
4
5
6
7
8342311003
0017108020
8342350103
0602320150
1502336004
020108060
011208035
MUFFLER
1
HEX HEAD BOLT
6
EXHAUST PIPE
1
GASKET ......................................... 1 .......... KUBOTA 15471-12231
GASKET
1
HEX NUT
4
HEX HEAD BOLT
2
QTY.
REMARKS
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 59
DCA-10SPX3 — FUEL FILTER ASSY.
FUEL FILTER ASSY.
PAGE 60 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — FUEL FILTER ASSY.
FUEL FILTER ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART NO.
0966141000
1024442320
0605513105
0017106016
B0368700004
0017108020
1491142750
6837151210
0017108035
1522143010
7000043081
011208025
7675528004
0966181000
0605513106
PART NAME
QTY.
REMARKS
RETURN HOSE
1
HOSE BAND ................................... 2 .......... REPLACES
SUCTION HOSE
1
HEX.HEAD BOLT
2
BRACKET, FUEL FILTER
1
HEX. HEAD BOLT ........................... 2 .......... REPLACES
HOSE BAND ................................... 6 .......... REPLACES
PUMP, FUEL ................................... 1 .......... REPLACES
HEX. HEAD BOLT
2
FUEL FILTER .................................. 1 .......... REPLACES
CARTRIDGE ................................... 1 .......... REPLACES
HEX. HEAD BOLT ........................... 2 .......... REPLACES
BRACKET, FUEL FILTER
1
SUCTION HOSE
1
SUCTION HOSE
1
P/N 0605515072
P/N 0017108020
P/N 0605515070
P/N 0602023155
P/N 0602042462
P/N 0602042551
P/N 0017108025
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 61
DCA-10SPX3 — ENCLOSURE ASSY.
ENCLOSURE ASSY.
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT IF NOT IN TEAL:
MQW-WHITE
SK-SCARLET/ORANGE
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 62 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — ENCLOSURE ASSY.
ENCLOSURE ASSEMBLY
NO.
PART NO.
PART NAME
1
2
3
4
7565111403
8445116114
0017106016
7565121502
8325921204
0017108020
1625165103
1625165204
8322313003
8345925004
0017108020
8435125004
8345923004
0017108020
8345130203
8435132113
0017112030
B0445000302
0017108020
7565144104
0017108020
B0445200203
B0445600104
0207006000
0605010230
0021805012
0810015204
0810015504
0017106016
B0465000202
8325961104
0017108020
8325172103
8325972104
8325173004
0207006000
0017108035
8325170203
832597020
B0445000203
8345970404
8325171113
0207006000
B9114000002
0021806016
0845047204
0845045004
0845047104
0845045004
0017108020
0845031504
0601850097
8435525003
0017108020
0600500090
0021106020
BASE ........................................................ 1 ........... 8325110122
FLOOR PANEL
1
HEX.HEAD BOLT
8
FRONT FRAME
1
LINING
1
HEX. HEAD BOLT
7
FILLER COVER
1
CHAIN
1
COVER, MUFFLER
1
LINING
1
HEX. HEAD BOLT
4
COVER, FRONT FRAME
1
LINING
1
HEX. HEAD BOLT
6
HANGER
1
HANGER
1
HEX. HEAD BOLT
6
REAR FRAME
7
HEX. HEAD BOLT
7
COVER, REAR FRAME
1
HEX. HEAD BOLT
6
DOOR, REAR FRAME
1
WINDOW PLATE
1
HEX.NUT
7
DOOR HANDLE
1
MACHINE SCREW
4
HINGE
2
WASHER
2
HEX.HEAD BOLT
4
ROOF PANEL
1
LINING
1
HEX. HEAD BOLT
16
SIDE PANEL
1
LINING
1
DUCT
1
HEX. NUT
5
HEX. HEAD BOLT
6
SIDE DOOR
1
LINING
1
SIDE DOOR
1
LINING
1
DUCT
1
HEX. NUT
6
DOOR HANDLE
1
MACHINE SCREW
4
HINGE
2
WASHER
2
HINGE
2
WASHER
2
HEX. HEAD BOLT
8
CAP
4
STOPPER
2
BRACKET
1
HEX. HEAD BOLT
4
EMBLEM
1
MACHINE SCREW
2
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
QTY.
REMARKS
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 63
DCA-10SPX3 — ENCLOSURE (RUBBER SEALS) ASSY.
ENCLOSURE (SEALS )ASSY.
PAGE 64 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — ENCLOSURE (RUBBER SEALS) ASSY.
ENCLOSURE (RUBBER SEALS )ASSY.
NO.
1
2
3
4
5
6
7
8
9
PART NO.
0229400650
0229400895
0229200650
0220400650
0227600895
0229400265
0229400550
0229200580
0229200245
PART NAME
RUBBER SEAL
RUBBERSEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
QTY.
3
2
1
2
2
2
1
2
2
REMARKS
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 65
DCA-10SPX3 — NAME PLATE AND DECALS
NAME PLATE AND DECALS
PAGE 66 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
DCA-10SPX3 — NAME PLATE AND DECALS
NAME PLATE AND DECALS
NO. PART NO.
PART NAME
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
WARNING! TRANSFER SWITCH
1
IMPORTANT “CHECK DAILY”
1
DANGER: ELEC.SHOCK HAZARD
1
STRIPE; FRONT END
1
DANGER: REMOVE ONLY WHEN COOL 1
WATER
1
WARNING
1
15 STRIPE
2
STRIPE; DOOR
2
DRAIN FUEL PRIOR TO LIFTING
2
SUPPORT HOOK
2
STRIPE: DOOR WITH HANDLE
2
OIL LEVEL CHECK
1
STRIPE; FRONT SIDE
2
MQ DECAL
1
120V
1
60HZ
1
GROUND
1
+
1
1
DO OPERATE WITH DOORS OPEN
1
OIL DRAIN PLUG
1
WATER DRAIN PLUG
1
0820610404
6390671104
8700611904
7670633003
1630610304
6360620104
8700611804
7670633804
7670633404
M0000001020Q
1320621504
7670633504
M9503000103
7670633204
0840625902
0800622704
M0000001021Q
0800628504
0800689404
0800689504
1630610504
6360620204
6360620104
QTY.
REMARKS
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 67
KUBOTA D1403— CRANKCASE ASSY.
CRANKCASE ASSY.
PAGE 68 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— CRANKCASE ASSY.
CRANKCASE ASSY.
NO.
010
020*
030*
040*
050*
060*
070*
080*
090*
100*
110*
120*
130*
140*
150
160
170
180
190
200
210
220
230
240
250
260
PART NO.
1641401010
3415027580
3221027580
1552196020
1552196030
1739196160
0631175045
1522103383
1522103392
0501200408
0501200609
0501200612
0501201018
1522133650
1522133610
1502133660
1522133700
1532173340
1547135010
1529635150
0105350650
0451260060
1920235660
0571200410
1522135682
1584139010
PART NAME
QTY. REMARKS
COMP. CRANKCASE ..................... 1 ....... INCLUDES ITEMS W/*
PLUG
1
PLUG
2
PLUG
5
PLUG
2
PLUG, EXPANSION
3
PLUG, EXPANSION
1
CAP, SEALING ............................... 5 ....... REPLACES 1522103380
CAP, SEALING ............................... 2 ....... REPLACES 1522103390
PIN, STRAIGHT
2
PIN, STRAIGHT
2
PIN, STRAIGHT
2
PIN, STRAIGHT
1
PIN, PIPE
1
PLUG
1
GASKET
1
O RING
1
PIPE, WATER RETURN
1
ASSY. PUMP, OIL
1
GASKET, OIL PUMP
1
BOLT
4
LOCK WASHER
4
OIL PUMP DRIVE GEAR
1
FEATHER KEY
1
FLANGE NUT
1
OIL SWITCH
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 69
KUBOTA D1403— OIL PAN ASSY.
OIL PAN ASSY.
PAGE 70 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— OIL PAN ASSY.
OIL PAN ASSY.
NO.
010
020
030
040
050
060
070
080
090
100
110
PART NO.
1929901613
1531301620
1733391010
152133750
7000065259
1595133750
0472400160
1562832110
0112360814
0481100160
1711136410
PART NAME
QTY. REMARKS
OIL PAN
1
OIL PAN GASKET
1
FLANGE BOLT
20
PLUG
1
GASKET ...................................... 1 ... REPLACES 1510933660
DRAIN PLUG
1
GASKET
1
OIL FILTER
1
BOLT
1
O RING
1
OIL GAUGE
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 71
KUBOTA D1403— CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 72 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
010
020
030
040
050
060
070
080
090*
100*
110*
120*
130*
140
150
160
PART NO.
1522101750
1641501752
0112360816
1547191530
0215650080
0451260080
0401250080
1641403040
1522103370
1522103490
1526196010
1732113580
1732113560
1901303450
1642703310
1949883040
PART NAME
QTY. REMARKS
ENGINE HOOK
1
ENGINE HOOK
1
BOLT
1
STUD
1
NUT
1
LOCK WASHER
1
PLAIN WASHER
1
COMP. CYLINDER HEAD ............. 1 ... INCLUDES ITEMS W/*
SEALING CAP
9
SEALING CAP
1
PLUG
2
INLET VALVE GUIDE
3
EXHAUST VALVE GUIDE
3
CYLINDER HEAD BOLT
14
CYLINDER HEAD GASKET
1
THERMOSWITCH ASSY.
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 73
KUBOTA D1403— GEAR CASE ASSY.
GEAR CASE ASSY.
PAGE 74 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— GEAR CASE ASSY.
GEAR CASE ASSY.
NO.
010
020*
030*
040*
050*
060*
070
080
090
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
250
260
270
280
290
300
310
PART NO.
1718204010
1685196010
0481100150
0481100360
1981856280
0501200612
1708904130
0112350860
0115350870
1736791030
0115350880
1736791020
0115350895
0451260080
0401250080
1552132290
0401150180
1524136950
1552136930
0771503213
1552173320
1576673330
0102350620
7000032091
1585233140
0481150300
1718233110
1547254550
1718291510
0451260060
0205650060
PART NAME
QTY. REMARKS
GEAR CASE ASSY. ....................... 1 ....... INCLUDES ITEMS W/*
PLUG
2
O RING
3
O RING
1
START SPRING PIN
1
STAIGHT PIN
2
GEAR CASE GASKET
1
BOLT
2
BOLT
5
BOLT
1
BOLT
3
BOLT
3
BOLT
2
LOCK WASHER
10
PLAIN WASHER
1
PIPE JOINT
1
PLAIN WASHER
1
SPRING
1
VALVE SEAT
1
BALL
1
WATER RETURN FLANGE
1
WATER FLANGE GASKET
1
BOLT
3
OIL FILTER CARTRIDGE ............... 1 ....... REPLACES 1732132430
OIL FILLER PLUG
1
O RING
1
OIL FILLER FLANGE
1
GASKET
1
STUD
4
LOCK WASHER
4
NUT
4
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 75
KUBOTA D1403— MAIN BEARING CASE ASSY.
MAIN BEARING CASE ASSY.
PAGE 76 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403 — MAIN BEARING CASE ASSY.
MAIN BEARING CASE ASSY.
NO.
010
020
030
040
050
060
070
080
090
100
110
120
PART NO.
1901304090
1901304540
1907704360
1901304813
1711804830
0112350825
0112350828
1920204460
1901304040
1901304050
1901304060
1560104560
PART NAME
MAIN BEARING CASE ASSY.
BEARING CASE BOLT
BEARING CASE GASKET
BEARING CASE COVER
CASE COVER GASKET
BOLT
BOLT
OIL SEAL
MAIN BEARING CASE ASSY.
MAIN BEARING CASE ASSY.
MAIN BEARING CASE ASSY.
BEARING CASE BOLT
QTY.
1
6
1
1
1
8
8
1
1
1
1
2
REMARKS
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 77
KUBOTA D1403— INLET MANIFOLD ASSY.
INLET MANIFOLD ASSY.
PAGE 78 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— INLET MANIFOLD ASSY.
INLET MANIFOLD ASSY.
NO.
010
020
030
040
PART NO.
1718211760
1718205550
1732611820
0112350822
PART NAME
INLET MANIFOLD
BREATHER JOINT
IN-MANIFOLD GASKET
BOLT
QTY. REMARKS
1
1
1
5
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 79
KUBOTA D1403— EXHAUST MANIFOLD ASSY.
EXHAUST MANIFOLD ASSY.
PAGE 80 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— EXHAUST MANIFOLD ASSY.
EXHAUST MANIFOLD ASSY.
NO.
010
020
030
040
050
060
PART NO.
1927412312
1531312350
1522191530
1642992010
151350822
1526312370
PART NAME
EXHAUST MANIFOLD
EX-MANIFOLD GASKET
STUD
NUT
STUD
MUFFLER GASKET
QTY.
1
1
6
6
4
1
REMARKS
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 81
KUBOTA D1403— VALVE AND ROCKER ASSY.
VALVE AND ROCKER ASSY.
PAGE 82 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— VALVE AND ROCKER ASSY.
VALVE AND ROCKER ASSY.
NO.
010
020
030
040
050
060
070
080
090*
100
110
120
130
140
150
160
170
180
190
200#
210#
PART NO.
1648413110
1648413120
1522113240
1522113330
1522113360
1522113150
1522113280
1540114052
0341000808
1522114350
1552191500
0215650080
0451260080
0401250080
0541100528
1522114430
1522114310
0461200140
1562114030
1552114230
1502114240
PART NAME
QTY. REMARKS
INLET VALVE
3
EXHAUST VALVE
3
VALVE SPRING
6
VALVE SPRING RETAINER
6
VALVE SPRING COLLET
6
VALVE STEM SEAL
6
VALVE CAP
6
ROCKER ARM SHAFT ASSY. ....... 1 ....... INCLUDES ITEMS W/*
SET SCREW
2
ROCKER ARM BRACKET
3
STUD
3
NUT
3
LOCK WASHER
3
PLAIN WASHER
3
SPRING PIN
1
ROCKER ARM SHAFT WASHER 2
ROCKER ARM SPRING
2
EXTERNAL CIR CLIP
2
ROCKER ARM ASSY. .................... 6 ....... INCLUDES ITEMS W/#
ADJUSTING SCREW
6
NUT
6
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 83
KUBOTA D1403— HEAD COVER ASSY.
HEAD COVER ASSY.
PAGE 84 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— HEAD COVER ASSY.
HEAD COVER ASSY.
NO.
010
020
030
040
PART NO.
1718214510
1552114520
1718205020
1711405130
PART NAME
HEAD COVER
HEAD COVER GASKET
COMP. BREATHER
GASKET
050
060
070
080
090
100
110
0112350840
1624105670
1718214490
1718205510
0931888200
1545192330
1502133660
BOLT
BREATHER ELEMENT
PLATE
BREATHER TUBE
HOSE CLAMP
CAP NUT
GASKET
QTY.
1
1
1
REMARKS
2
2
1
1
1
2
3
3
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 85
KUBOTA D1403— CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 86 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
010
020
030
040*
050*
060*
070*
080*
090
100
110#
120
130
140
150
160
PART NO.
1560115550
1901315110
1733116010
1733116150
1552193610
1552116510
0571200720
1522116270
0112350818
1522124010
1642724980
1552124360
1552124370
1522124320
1981824250
0112350818
PART NAME
QTY. REMARKS
TAPPET
6
PUSH ROD
6
CAMSHAFT ASSY. ........................ 1 ....... INCLUDES ITEMS W/*
CAMSHAFT
1
SET SCREW
1
CAM GEAR
1
FEATHER KEY
1
CAMSHAFT STOPPER
1
BOLT
2
IDLE COMP. GEAR ........................ 1 ....... INCLUDES ITEMS W/#
IDLE GEAR BUSHING
1
COLLAR
1
COLLAR
1
IDLE GEAR CIR. CLIP
1
IDLE GEAR SHAFT
1
BOLT
3
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 87
KUBOTA D1403— PISTON AND CAMSHAFT ASSY.
PISTON AND CAMSHAFT ASSY.
PAGE 88 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— PISTON AND CAMSHAFT ASSY.
PISTON AND CRANKSHAFT ASSY.
NO.
010
010
020
020
030
040
050
060*
070*
080*
080
080
090
100#
110#
120
130
140
150
160
170
180
180
180
190
190
190
200
200
200
210
210
210
220
PART NO.
1642721110
1642721910
1642721050
1642721090
1490121310
1410921330
1731122010
1733121980
1552122142
1731122310
1733122970
1733122980
1641423010
0771500401
1920223280
1547124110
0571200720
1547123312
1920223250
0481110300
1522123360
1731123470
1731123910
1731123920
1731123480
1731123930
1731123940
1552123530
1522123950
1522123960
1920223540
1920223970
1920223980
1920204140
PART NAME
QTY. REMARKS
PISTON .......................................... 3 ....... S T D
PISTON .......................................... 3 ....... + 0.5 M M
PISTON RING ASSY. ..................... 3 ....... STD
PISTON RING ASSY ..................... 3 ....... +0.50MM
PISTON PIN
3
PISTON PIN CLIP
6
CONNECTING ROD ASSY. ............ 3 ....... INCLUDES ITEMS W/*
PISTON PIN BUSHING
3
CONNECTING ROD BOLT
6
METAL CRANKPIN ........................ 3 ....... STD SET
METAL CRANKPIN ........................ 3 ....... -0.20MM,SET
METAL CRANKPIN ........................ 3 ....... -0.40MM,SET
COMP. CRANKSHAFT ................... 1 ....... INCLUDES ITEMS W/#
BALL
3
CRANKSHAFT BUSHING
1
CRANK GEAR
1
FEATHER KEY
1
OIL SLINGER
1
CRANKSHAFT COLLAR
1
O RING
1
CRANKSHAFT NUT
1
METAL CRANKSHAFT ................... 1 ....... STD
METAL CRANKSHAFT ................... 1 ....... -0.20MM
METAL CRANKSHAFT ................... 1 ....... -0.40MM
METAL CRANKSHAFT ................... 3 ....... STD SET
METAL CRANKSHAFT ................... 3 ....... -0.20MM, SET
METAL CRANKSHAFT ................... 3 ....... -0.40MM, SET
SIDE METAL .................................. 2 ....... STD
SIDE METAL .................................. 2 ....... +0.20MM
SIDE METAL .................................. 2 ....... +0.40MM
SIDE METAL .................................. 2 ....... STD
SIDE METAL .................................. 2 ....... +0.20MM
SIDE METAL .................................. 2 ....... +0.40MM
OIL SEAL
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 89
KUBOTA D1403— FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 90 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
010
020*
030
040
050
060
070
080
100
110
120
PART NO.
1722225010
1560263820
1532125163
1747504610
0152104680
1552104790
0112360816
0107351032
0451260100
0107351250
0451260120
PART NAME
QTY.
REMARKS
FLYWHEEL COMP. .................... 1 ............. INCLUDES ITEMS W/*
RING GEAR
1
FLYWHEEL BOLT
6
FLYWHEEL HOUSING
1
COVER
1
COVER PACKING
1
BOLT
2
BOLT
11
LOCK WASHER
11
BOLT
2
LOCK WASHER
2
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 91
KUBOTA D1403— STARTER ASSY.
STARTER ASSY.
PAGE 92 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— STARTER ASSY.
STARTER ASSY.
NO.
010
020
030
040
050
060
070
PART NO.
7000065440
0151751028
0113351030
0217650100
0451260100
0211450080
0451260080
PART NAME
QTY. REMARKS
STARTER ASSY. ............................ 1 ....... REPLACES 1738163012
STUD
1
BOLT
1
NUT
1
LOCK WASHER
1
NUT
1
LOCK WASHER
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 93
KUBOTA D1403— STARTER (COMPONENTS) ASSY.
STARTER (COMPONENTS) ASSY.
PAGE 94 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— STARTER (COMPONENTS) ASSY.
STARTER (COMPONENTS) ASSY.
NO.
010
PART NO.
7000065440
020*
030*
040*#
050*#
060*
070*
080*
090*
100*
110*%
120*
130*
140*
150*
160*
170*
180*
190*
200*
210*
220*
1119763080
1119763070
1146063500
1146063530
1562163040
1648463030
1648463020
1648463200
1738163380
1540163390
1146063270
1146063110
1921263100
1146063120
1921297130
1146093310
1551196660
1119763320
1551163760
1628563570
1396392010
PART NAME
QTY. REMARKS
STARTER ASSY. ............................ 1 ....... INCLUDES ITEMS W/*;
REPLACES 1738163012
YOKE ASSY.
1
ARMATURE ASSY. ........................ 1 ....... INCLUDES ITEMS W/#
BEARING
1
BEARING
1
OVER RUNNING CLUTCH
1
DRIVE END FRAME
1
MAGNETIC SWITCH
1
END FRAME
1
BRUSH HOLDER ASSY. ................ 1 ....... INCLUDES ITEMS W/%
BRUSH SPRING
4
GEAR
1
RETAINER
1
ROLLER
5
SPRING
1
BALL
1
BOLT
2
O RING
2
BOLT
2
BOLT ASSY.
2
DRAIN PIPE
1
HEXAGON NUT
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 95
KUBOTA D1403— INJECTION PUMP 1 ASSY.
INJECTION PUMP 1 ASSY.
PAGE 96 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— INJECTION PUMP 1 ASSY.
INJECTION PUMP 1 ASSY.
NO.
010
020
020
020
040
050
060
070
080
090
100*
110
120
130
140
150#
PART NO.
1718251010
1641452090
1641452110
1641452120
0112350822
1522191530
0215650080
0451260080
1574860570
1712152030
1984452040
1526352140
0102350616
1411142410
1468142010
1430142750
PART NAME
QTY. REMARKS
INJECTION PUMP ASSY.
1
INJECTION SHIM .......................... 1 ....... 0.20MM
INJECTION SHIM .......................... 1 ....... 0.25MM
INJECTION SHIM .......................... 1 ....... 0.30MM
BOLT
2
STUD
2
NUT
2
LOCK WASHER
2
ORIFICE ASSY.
1
FUEL PUMP ASSY. ....................... 1 ....... INCLUDES ITEMS W/*
DIAPHRAGM COMP.
1
FUEL PUMP GASKET
1
BOLT
2
EYE JOINT
1
FUEL PIPE ASSY. ......................... 1 ....... INCLUDES ITEMS W/#
PIPE CLIP
2
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 97
KUBOTA D1403— INJECTION PUMP 2 ASSY.
INJECTION PUMP 2 ASSY.
PAGE 98 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— INJECTION PUMP 2 ASSY.
INJECTION PUMP ASSY. 2
NO.
010
020*
030*
040*
050*
060*
070*
080*
090*
100*
110*
120*
130*
140*
150*
180*
190*
200*
210*
PART NO.
1718251010
1718251050
1647551030
1647551230
1142051240
1641551220
1641551610
1522151070
1461151250
1948451460
1522151280
1522151270
1522151290
1907751490
1718251060
1707951380
1552151320
1522196650
1461151200
PART NAME
QTY. REMARKS
INJECTION PUMP ASSY. ............. 1 ....... INCLUDES ITEMS W/*
PUMP PLUNGER
3
DELIVERY VALVE
3
DELIVERY VALVE SPRING
3
DELIVERY VALVE GASKET
3
DELIVERY VALVE HOLDER
3
LOCK PLATE ASSY.
1
TAPPET ASSY.
3
TAPPET GUIDE PIN
3
PLATE
1
PLUNGER SPRING
3
UPPER SPRING SEAT
3
LOWER SPRING SEAT
3
SHIM
3
CONTROL RACK
1
CONTROL SLEEVE
3
FOLLOW SCREW
1
GASKET
2
O RING
3
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 99
KUBOTA D1403— FUEL CAMSHAFT ASSY.
FUEL CAMSHAFT ASSY.
PAGE 100 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— FUEL CAMSHAFT ASSY.
FUEL CAMSHAFT ASSY.
NO.
010
020*
030*
040*
050*
060*
070*
080*
090*
100*
110*
120*
140*#
150*#
160*
170*
180*
190
200
210
220
PART NO.
1718216020
1718216170
0815306205
1666251150
0571200525
0461200240
1981855450
1981855460
1981855510
1981855260
1666255270
1666255060
1981855280
198185380
166255620
1981855600
1981855340
0810306205
152216320
0112360814
0461200250
PART NAME
QTY. REMARKS
FUEL CAMSHAFT ASSY. .............. 1 ....... INCLUDES ITEMS W/*
FUEL CAMSHAFT
1
BALL BEARING
1
INJECTION PUMP GEAR
1
FEATHER KEY
1
EXTERNAL CIR. CLIP
1
GOVERNOR SLEEVE
1
THRUST WASHER
2
GOVERNOR WEIGHT COLLAR
1
GOVERNOR WEIGHT SHAFT
2
GOVERNOR WEIGHT HOLDER
1
GOVERNOR WEIGHT COMP. ........ 2 ....... INCLUDES ITEMS W/#
GOVERNOR WEIGHT PIN
2
GOVERNOR BUSHING
4
PLAIN WASHER
4
BEARING
2
WASHER
2
BALL BEARING
1
CAMSHAFT FUEL STOPPER
1
BOLT
2
EXTERNAL CIR. CLIP
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 101
KUBOTA D1403— GOVERNOR ASSY.
GOVERNOR ASSY.
PAGE 102 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— GOVERNOR ASSY.
GOVERNOR ASSY.
NO.
010
020*
030*
040*
050*
060*
070*
080*
090
100
110
120
130
140
150
160
170
PART NO.
1718256050
1707656130
1981856150
0105350518
0451260050
1707656230
1522166410
0451260060
0112350832
0102350628
0401250080
0401250060
1981856480
1718256412
1718256420
1981855600
1981855340
PART NAME
QTY. REMARKS
FORK LEVER ASSY. ..................... 1 ....... INCLUDES ITEMS W/*
FORK LEVER
1
FORK LEVER SHAFT
1
BOLT
1
LOCK WASHER
1
FORK LEVER HOLDER
1
BOLT
1
LOCK WASHER
1
BOLT
2
BOLT
1
PLAIN WASHER
2
PLAIN WASHER
1
START SPRING
1
GOVERNOR SPRING
1
GOVERNOR SPRING
1
BEARING
2
WASHER
2
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 103
KUBOTA D1403— SPEED CONTROL PLATE ASSY.
SPEED CONTROL PLATE ASSY.
PAGE 104 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— SPEED CONTROL PLATE ASSY.
SPEED CONTROL PLATE ASSY.
NO.
010
020
030
040
050
070
080
090
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
250
PART NO.
1981854120
1560192010
1560196650
1584114620
1622154420
1707657110
1707657740
1707656110
0481110160
0481110070
1362216670
1707957380
1707657162
3691927820
1584192010
1707657152
0541100318
1707657510
0501200412
1543957210
0102350620
1522188210
0451260060
0205650060
PART NAME
ADJUSTING BOLT
NUT
GASKET
CAP NUT
CAP
SPEED CONTROL PLATE
LEVER SHAFT
GOVERNOR LEVER
O RING
O RING
CAMSHAFT SHIM
COLLAR
CHANGE LEVER
PTO LEVER GRIP
SPEED CONTROL NUT
SPEED CONTROL LEVER
SPRING PIN
CHANGE SPRING
STRAIGHT PIN
GASKET
BOLT
STUD
LOCK WASHER
NUT
QTY.
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
2
2
REMARKS
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 105
KUBOTA D1403— ENGINE STOP LEVER ASSY.
ENGINE STOP LEVER ASSY.
PAGE 106 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403 — ENGINE STOP LEVER ASSY.
ENGINE STOP LEVER ASSY.
NO.
010
020*
030*
040*
050*
060*
070
080#
090#
100#
110#
120#
130#
140
150
160
170
180
190
200
210
220
PART NO.
1707654093
1707654103
1540192010
1552192330
1502133660
1552154270
1748257702
1718351650
1733157740
1748257720
1547157980
0541100420
1748257920
1510857280
0205650060
1529651660
0102350618
0102350622
0401250060
1718316210
3539437860
0112350865
PART NAME
QTY. REMARKS
IDILING APPARATUS ..................... 1 ....... INCLUDES ITEMS W/*
ASJUSTMENT BOLT ASSY.
1
NUT
1
CAP NUT
1
GASKET
2
CAP
1
ENGINE STOP LEVER ASSY. ....... 1 ....... INCLUDES ITEMS W/#
INJECTION PUMP COVER
1
LEVER SHAFT
1
ENGINE STOP LEVER
1
OIL SEAL
1
SPRING PIN
1
RETURN SPRING
1
STOPPER
1
NUT
1
PUMP COVER GASKET
1
BOLT
2
BOLT
2
PLAIN WASHER
2
FUEL CAMSHAFT COVER
1
GASKET
1
BOLT
4
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 107
KUBOTA D1403— STOP SOLENOID ASSY.
STOP SOLENOID ASSY.
PAGE 108 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— STOP SOLENOID ASSY.
STOP SOLENOID ASSY.
NO.
010
020
030
040
050
060
070
080
PART NO.
1547160010
0112360816
0401250080
1733160150
1547160162
0401250060
0552550600
1718260110
PART NAME
STOP SOLENOID
BOLT
PLAIN WASHER
STOP LEVER
STOP LEVER
PLAIN WASHER
SNAP PIN
SOLENOID SUPPORT
QTY.
1
2
2
1
1
3
3
1
REMARKS
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 109
KUBOTA D1403 — ALTERNATOR ASSY.
ALTERNATOR ASSY.
PAGE 110 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403 — ALTERNATOR ASSY.
ALTERNATOR ASSY.
NO.
010
020
030
040
050
060
070
080
090
100
110
PART NO.
1642764010
TA04074020
0117351000
0115360830
0451260080
0215650100
0451260100
0401150100
0401560080
0205650060
0451260060
PART NAME
ALTERNATOR ASSY.
DYNAMO STAY
BOLT
BOLT
LOCK WASHER
NUT
LOCK WASHER
PLAIN WASHER
PLAIN WASHER
NUT
LOCK WASHER
QTY.
1
1
1
1
1
1
1
1
1
1
1
REMARKS
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 111
KUBOTA D1403— ALTERNATOR (COMPONENTS) ASSY.
ALTERNATOR (COMPONENTS) ASSY.
PAGE 112 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— ALTERNATOR (COMPONENTS) ASSY.
ALTERNATOR (COMPONENTS) ASSY.
NO.
010
020*
030*
040*
050*
060*#
070*#
090*
100*
110*%
120*%
130*%
140*%
150*
160*
170*
180*
190*&
200*&
210*
220*
230*
240*
250*
260*
270*
280*
PART NO.
1642764010
1642764110
1588192010
1588164150
1588164040
1588164800
1588164770
1642764020
1588164710
1588193010
1588164260
1588164780
1624164060
1624164230
1623164850
1624164900
1588164310
1588164090
1588164330
1588193020
1588193030
1588193040
1588191040
1588192020
1588191050
1418292030
1588164600
PART NAME
QTY. REMARKS
ALTERNATOR ASSY. ..................... 1 ....... INCLUDES ITEMS W/*
ALTERNATOR PULLEY
1
NUT
1
COLLAR
1
ROTOR ........................................... 1 ....... INCLUDES ITEMS W/#
BEARING COVER
1
BALL BEARING
1
DRIVE END FRAME
1
RETAINER PLATE .......................... 1 ....... INCLUDES ITEMS W/%
ROUND HEAD SCREW
4
THROUGH BOLT
2
BALL BEARING
1
END FRAME
1
END COVER
1
RECTIFIER ASSY.
1
INSULATION BUSH
1
BRUSH HOLDER ............................ 1 ....... INCLUDES ITEMS W/&
BRUSH
2
BRUSH SPRING
2
ROUND HEAD SCREW
2
ROUND HEAD SCREW
6
ROUND HEAD SCREW
1
BOLT
3
NUT
2
BOLT
2
NUT
1
REGULATOR ASSY.
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 113
KUBOTA D1403— FAN ASSY.
FAN ASSY.
PAGE 114 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— FAN ASSY.
FAN ASSY.
NO.
010
020
030
040
050
060
PART NO.
1734574110
1981874150
0175450625
1728874280
0571200720
1726697011
PART NAME
QTY. REMARKS
FAN
1
FAN COLLAR
1
FLANGE BOLT
4
FAN DRIVE PULLEY
1
FEATHER KEY
1
V BELT ........................................... 1 ....... REPLACES 1726697010
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 115
KUBOTA D1403 — WATER FLANGE AND THERMOSTAT ASSY.
WATER FLANGE AND THERMOSTAT ASSY.
PAGE 116 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403 — WATER FLANGE AND THERMOSTAT ASSY.
WATER FLANGE AND THERMOSTAT ASSY.
NO.
010
020*
030
040
050
060
070
080
090
100
110
120
130
140
150
160
PART NO.
1551272702
1733173342
1576672920
0112350822
0151350822
0115350870
0215650080
0451260080
1552173340
1510973360
1532173260
1531373270
0112350835
1943473010
1551296010
0471702150
PART NAME
QTY. REMARKS
WATER FLANGE COMP. ................ 1 ....... INCLUDES ITEMS W/*
WATER RETURN PIPE
1
WATER FLANGE GASKET
1
BOLT
2
STUD
1
BOLT
1
NUT
1
LOCK WASHER
2
WATER RETURN PIPE
1
PIPE BAND
2
THERMOSTAT COVER
1
THERMOSTAT GASKET
1
BOLT
2
THERMOSTAT ASSY.
1
PLUG
1
WASHER WITH RUBBER
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 117
KUBOTA D1403— WATER PUMP ASSY.
WATER PUMP ASSY.
PAGE 118 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— WATER PUMP ASSY.
WATER PUMP ASSY.
NO.
010
020*
030*
040*
050*
060
070
080
090
100
110
120
PART NO.
1552173033
1552173550
1666173510
1666173050
1552173520
1576673430
0112350828
1552191510
0451260080
0215650080
0102350618
1547174250
PART NAME
QTY. REMARKS
WATER PUMP ASSY. .................... 1 ....... INCLUDES ITEMS W/*
BEARING
1
IMPELLER
1
MECHANICAL SEAL ASSY.
1
WATER PUMP FLANGE
1
WATER PUMP GASKET
1
BOLT
2
STUD
2
LOCK WASHER
2
NUT
2
BOLT
8
FAN PULLEY
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 119
KUBOTA D1403— RADIATOR ASSY.
RADIATOR ASSY.
PAGE 120 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403— RADIATOR ASSY.
RADIATOR ASSY.
NO.
010
020*
030*
040*
050*
060
070
080
090
100
110
120
130*#
PART NO.
1559672060
1552172330
1527272020
1559672710
1547172730
1546172850
170637294
1510872870
1553772410
1718273340
1540111720
1430142750
1907787240
PART NAME
QTY. REMARKS
RADIATOR ASSY. .......................... 1 ....... INCLUDES ITEMS W/*
FAN SHROUD
1
CAP ASSY. .................................... 1 ....... INCLUDES ITEMS W/#
HOSE
1
HOSE BAND
2
LOWER HOSE
1
UPPER HOSE
1
HOSE BAND
4
OVERFLOW HOSE
1
HOSE
1
HOSE BAND
2
HOSE BAND
4
DECAL; CAUTION
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 121
KUBOTA D1403 — FUEL FILTER ASSY.
FUEL FILTER ASSY.
PAGE 122 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
KUBOTA D1403 — FUEL FILTER ASSY.
FUEL FILTER ASSY.
NO.
010
030*
040*
050*
060*
070*
080*
090*
100*
110*#
120*
130*
140*
150*
PART NO.
1707643012
1552143522
1552143672
1552143552
1552143542
0481110290
1552193310
1552143150
1552143100
1687388430
1552143160
0481150650
1552143930
0481100160
PART NAME
QTY. REMARKS
FUEL FILTER ASSY. ...................... 1 ....... INCLUDES ITEMS W/*
FILTER HANDLE
1
GASKET
1
HANDLE RETAINER
1
THRUST PLATE
1
O RING
1
WASHER WITH SCREW
2
RETAINER RING
1
FILTER CUP ASSY. ....................... 1 ....... INCLUDES ITEMS W/#
FUEL LABEL
1
FILTER ELEMENT
1
O RING
1
SPRING
1
O RING
1
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 123
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5.
Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
6.
The following items are not returnable:
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
a.
SPECIAL EXPEDITING SERVICE
Terms of payment for parts are net 30 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
b.
MINIMUM ORDER
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
RETURNED GOODS POLICY
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
1.
2.
A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
c.
Any line item with an extended
dealer net price of less than
$5.00.
d.
Special order items.
e.
Electrical components.
f.
Paint, chemicals, and lubricants.
g.
Decals and paper products.
h.
Items purchased in kits.
7.
The sender will be notified of any material
received that is not acceptable.
To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
8.
Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
a.
The parts numbers and descriptions
must match the current parts price
list.
9.
b.
The list must be typed or computer
generated.
Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
c.
The list must state the reason(s)
for the return.
d.
The list must reference the sales
order(s) or invoice (s) under
which the items were originally
purchased.
e.
The list must include the name
and phone number of the person
requesting the RMA.
3.
A copy of the Return Material Authorization
must accompany the return shipment.
4.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
LIMITATIONS OF SELLER’S LIABILITY
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
Effective: February 22, 2006
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
PAGE 124 — DCA-10SPX3 A.C. GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (01/17/11)
NOTE PAGE
DCA-10SPX3 A.C. GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (01/17/11) — PAGE 125
PARTS AND OPERATION MANUAL
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
MQ Parts Department
Tel. (800) 421-1244
Fax (800) 537-3927
Service Department
800-421-1244
310-537-3700
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Warranty Department
Fax: 310-537-4259
800-421-1244
310-537-3700
Fax: 310-943-2249
Technical Assistance
800-478-1244
Fax: 310-943-2238
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Unit 2, Northpoint Industrial Estate,
Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected]
Tel: 0161 339 2223
Fax: 0161 339 3226
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2011, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the MQ Power logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement