WAGNER PaintMate Roller manual

Paintmate
PLUS
™
Quick Start Guide • Guide de démarrage rapide • Guía Rápida para comenzar
Plunger tube assembly • Assemblage pour le piston • Ensamblaje para el émbolo
1
2
3
Lubricate plunger O-rings
Insert plunger into main tube
Tighten locking collar securely
Lubrifier les joints toriques du piston
Insérer le piston dans le manche réservoir
Serrer solidement la bague de blocage
Lubrique las juntas tóricas del émbolo
Inserte el émbolo en el tubo principal
Ajuste firmemente el collar de sujeción
2
3
Setup • Montage • Disposición
1
or
Owner’s Manual (page 2)
Attach roller cover assembly
Attach roller arm
Mount fill tube / lid
Fixer l’ensemble du manchon du rouleau
Fixer le bras du rouleau
Installer le tube de remplissage et le
couvercle
Acople el conjunto de cubierta del rodillo
Acople el brazo del rodillo
4
5
6
Press fill valve onto tube
Pull the plunger to fill the tube
Squeeze Power Trigger™ and begin
Insérer la valve de remplissage dans le tube
Tirer le piston afin de remplir le tube
Presione la válvula de llenado en el tubo
Tire del émbolo para llenar el tubo
Serrer la détente Power Trigger™ et
commencer
Monte el tubo y la tapa de llenado
Read this manual for complete instructions
Manuel de l’utilisateur (page 8)
Lire ce manuel pour obtenir des directives complètes
Manual del usario (página 14)
Lea este manual para obtener las instrucciones completas
0911
• Form No. 0284781D
Patent pending
Español
Presione el gatillo Power Trigger™ y
comenzar
Français
English
Getting
Started
Parts and Components
Roller arm
assembly
Spatter
guard
Roller
core
Start
Roller cap
Roller
cover
Non-standard
container lid (not
included with
all models)
Head
Main
tube
Quick-release
tabs
Fill valve
Before you begin:
• Make sure the type of paint you use can
be cleaned with either mineral spirits (for
oil-based paints) or a warm water and soap
solution (for latex paints).
• It is a good idea to have drop cloths
protecting your floors and anything else in
the room that you do not want accidentally
splattered with paint.
Standard
container lid
Locking
collar
Fill tube
Trigger
Assembly
1
2
Plunger
3
important: Some oil-based paints require
a stronger cleaning solution than mineral
spirits and should not be used with the
PaintMate™ Plus. Using a cleaning solution
stronger than mineral spirits may cause
damage to the PaintMate™ Plus. Check
with your paint supplier to be sure the oilbased paint you have can be cleaned with
mineral spirits.
Questions?
Call Wagner Technical Service at:
1-800-760-3844
1. Remove plastic bag from plunger.
Lubricate the plunger O-rings with
petroleum jelly.
2. Insert the plunger into the main
tube. Make sure O-rings do
not twist or cut.
3. Tighten the locking collar.
4
5
6
4. Attach the roller cover assembly to
the roller arm.
5. Press the quick-release tabs on the
unit and attach the roller arm.
6. If painting a ceiling, attach the
spatter guard.
Register your product online at:
www.wagnerspraytech.com
English
2
1. Filling the
main tube
Attaching the container lid / fill tube
1
2
(a)
Start
Before filling:
Your PaintMate™ can be used with two types
of container lids that are used to allow you to
pull material from the material container into the
PaintMate™.
The lid below is desiged for use with standard,
one-gallon, round material containers. This lid
comes standard with your PaintMate™.
(a)
1. Slide the small end of the fill tube
(a) through the hole in the container
lid you plan to use.
2a. Standard containers - Attach the
container lid with fill tube securely
to the material container.
2b. All other containers - Thread the
container lid with fill tube onto the
material container.
Filling the main tube
Use the lid shown below if you are using
something other than a standard, one-gallon,
round material container. *Not included with
all models.
1
2
3
1. Apply a thin layer of petroleum
jelly to the fill tube. This will help
the fill valve slide easily off the fill
tube.
2. Press down and firmly hold the fill
valve onto the fill tube.
3. Pull the plunger to draw the
material into the main tube. When
the tube is full, you are ready to
begin using the PaintMate™.
3
English
2. Usage
General Rolling Tips:
Preparing the room
Remove all pictures, mirrors, and decorations
from the walls and draperies from the
windows. Remove all nails, hardware and
switch and receptacle covers. Cover furniture
and floor with drop cloths.
Surface Preparation
• Always remove wallpaper before painting.
Wash off old adhesive and rinse with
water. Allow the walls to dry before
painting.
• Wash and rinse dirt, grease and oil buildup off the walls with soap and water.
• Fill all nail holes, joints and cracks with
patching paste. Let dry and sand the
surface until smooth. Clean sanded area
with a damp cloth.
• Spot prime all patched areas and any
marker and/or pen marks before applying
first coat.
TIP: Write the important information from
your paint can (color, formula, brand and
paint type) on the back of a switch plate for
future reference.
English
Painting the Room
TIP: If you need more than one gallon of
paint to do the room’s walls, mix them
together to ensure color uniformity.
• Always make sure to open a window or
door to ensure proper ventilation. If you are
painting both the ceiling and walls in your
room, start with the ceiling first and then
move to the walls.
Loading the roller
1
Ceilings:
• To minimize spills and spatters, use the
spatter guard and paint across the short
width of the ceiling.
Walls:
• Tape off around base and window and
door trim.
• Paint one wall at a time.
• Pick an area to start where you can
saturate the roller cover and evenly
distribute the paint. Working in threefoot sections, begin by cutting-in around
windows, doors, cabinets, base and other
breaks in the wall surface with a pad or
brush.
• Start painting at one end of a wall and roll
out the letter “W”. Fill it in with crosswise
strokes, working your way across the wall
in 3’ x 3’ sections. Finish the sections by
painting one solid swipe from ceiling to
floor. This will give you a nice even paint
finish.
• Be careful not to over-saturate the roller
cover as it may drip, slide on the wall or
spatter.
• Make sure to run the roller cover over
the areas you cut-in around the trim and
baseboards to even out the texture.
• If you need to stop and take a break; finish
painting the entire wall, or stop at a break
in the wall such as a doorway or corner to
prevent lap marks.
4
1. Push plunger forward until you see paint coming through the roller cover.
2. Squeeze Power Trigger® for additional paint as needed.
3. Refill as needed (see Filling the Main Tube, page 3).
TIP: During extended break periods, place a plastic bag around the
roller cover and fill valve to keep it from drying out.
TIP: For best results, maintain a steady flow of material to the roller.
cover and avoid rolling it dry.
3. Cleanup
Start
Before you begin cleaning:
When cleaning the PaintMate™, make sure to
use the appropriate cleaning solution for the
type of material used.
• If you used latex-based materials,
use warm, soapy water to clean the
PaintMate™.
• If you used oil-based materials, use mineral
spirits.
Returning excess material to material container
1
2
3
4
1. Pull plunger back to draw
remaining material from
the roller arm assembly
into the tube.
2. Press the fill valve
onto the fill tube. Push
plunger forward to return
excess material into the
container.
3. Remove the spatter
guard. Press locking tab
and remove roller cover
assembly from the roller
arm.
4. Remove the roller cap.
Push the roller core out
the other end. Place
spatter guard, cap, core
and cover in a bucket of
the appropriate cleaning
solution.
Cleaning the PaintMate™
1
2
You will need:
3
x5
• A large bucket or other container that will
hold cleaning solution.
x5
TIP: A large laundry tub filled with warm,
soapy water is ideal for cleanup if you used
latex-based materials.
1. Remove fill tube from the container 2. Submerge the fill tube into the
lid. Install end of the fill tube into the
appropriate cleaning solution
valve housing.
and pull the plunger in and out a
minimum of 5 times.
4
3. Remove the fill tube. Submerge the
fill valve and roller arm and pull the
plunger in and out a minimum of 5
times.
5
x5
4. Remove the roller arm. Submerge
5. Clean the remaining parts (cap,
the head of the PaintMate™ and the
core, cover and spatter guard) by
fill valve and pull the plunger in and
hand using the appropriate cleaning
out a minimum of 5 times.
solution.
5
English
4. Storage
Start
Storage notes:
Proper cleaning and lubrication of certain
components of the PaintMate™ are critical to
prolonging the life of the components.
If after extended use the plunger has a
tendency to stick, apply a generous amount
of petroleum jelly located on the end of the
plunger (see Lubricating the components,
step 2).
important: When storing the
PaintMate™, make sure the fill valve is
pointing downward, and never store the
PaintMate™ with the fill tube inserted into
the fill valve.
Lubricating the components
1
2
3
1. Turn the locking collar as shown until 2. Lubricate around and in between the 3. Re-insert the plunger back inside the
the main tube slides easily off of the
plunger O-rings with petroleum jelly.
main tube. Make sure the O-rings
plunger.
do not twist or cut. Tighten the
locking collar.
4
5
Connecting areas
6
Seal
O-ring
4. Lubricate the inside of the fill valve
housing on the main tube with
petroleum jelly.
5. Clean and lubricate with petroleum
6. Reassemble roller cover. Place
jelly the indicated areas on the roller
back onto roller arm.
arm.
Cleaning the fill valve
1. Unscrew the locking cap (a) on the valve housing.
2. Remove the retainer disk (b) and the duckbill (c) from the
valve housing.
3. Clean these parts using the appropriate cleaning solution.
4. Replace the duckbill (c) and the retainer disk (b).
5. Screw the locking cap (a) back onto the valve housing.
(a)
Cleaning the fill valve note:
The inner parts of the fill valve should be
cleaned ONLY if you are experiencing leakage
problems, or if you are unable to draw material
into the main tube.
English
(b)
(c)
6
Troubleshooting
Problem A: There is leakage on the roller arm assembly.
Cause
Solution
1.
The roller arm seal is backwards.
Turn the seal around.
2.
The roller arm seal was not properly cleaned.
Clean and properly lubricate.
3.
The O-ring and the connecting areas on the roller arm were not cleaned properly.
Clean and properly lubricate (see Cleaning the PaintMate™ and Lubricating
the PaintMate™, pages 5-6).
4.
Residue on the connecting area inside of the head.
Clean out any remaining residue inside the head of the PaintMate™.
5.
The O-ring on the roller arm is damaged or missing.
Clean or replace*.
6.
The roller cover is worn or damaged.
Replace the roller cover*.
7.
The roller core or cap is worn or damaged.
Replace the roller core or cap*.
Problem B: Plunger is difficult to pull/push.
Cause
1.
The plunger O-rings are not lubricated.
Solution
Lubricate the plunger O-rings (see Lubricating the components, page 6)
Problem C: The main tube will not fill, or there is leakage from the fill valve.
1.
Cause
Solution
Residue on the fill valve components.
a) Insert the fill tube into the fill valve and twist the fill tube several times to break
up the residue.
b) If the problem persists, refer to Cleaning the fill valve, page 6.
* Replacement parts available by calling customer service
Have you tried the recommendations above and
are still having problems? In the United States, to
speak to a customer service representative, call
our Technical Service at 1-800-760-3844 Monday
through Friday between 8:00 AM and 4:30 PM
Central time.
Product Registration
Register your product online at www.wagnerspraytech.com.
Proper registration will serve as proof of purchase in the
event your original receipt becomes misplaced or lost.
Wagner one year limited warranty - Keep on file
This product, manufactured by Wagner Spray Tech Corporation (Wagner) is warranted against defects in material
and workmanship for one year following date of purchase if operated in accordance with Wagner’s printed
recommendations and instructions. This warranty does not cover damage resulting from improper use, accidents,
user’s negligence or normal wear. This warranty does not cover any defects or damages caused by service or
repair performed by anyone other than a Wagner Authorized Service Center.
ANY IMPLIED WARRANTY OF MERCHANTABlLITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED
TO ONE YEAR FOLLOWING DATE OF PURCHASE. THIS PRODUCT IS DESIGNED FOR HOME USAGE ONLY.
IF USED FOR COMMERCIAL OR RENTAL PURPOSES, THIS WARRANTY APPLIES ONLY FOR 30 DAYS
FROM DATE OF PURCHASE. WAGNER SHALL NOT IN ANY EVENT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FOR BREACH OF THIS WARRANTY OR ANY OTHER
REASON. THIS WARRANTY DOES NOT APPLY TO ACCESSORIES.
If any product is defective in material and/or workmanship during the applicable warranty period, return it with proof
of purchase, transportation prepaid, to any Wagner Authorized Service Center. Call the Wagner Technical Service
at 1-800-760-3844 Monday through Friday between 8:00 AM and 4:30 PM Central time.
7
English
Parts List • Liste de pièces • Lista de piezas
4
Optional Accessories • Accessoires Optional • Accesorios Opciónal
5
1
Part No.
Nº de piéce
Pieza No.
6
7
8
9
2
English
Description
Français
Description
Español
Descripción
0155206C
3/8” nap roller
cover
Manchon de rouleau à
grain de 3/8 ” (1 cm)
Cubierta del rodillo con
lanilla de 3/8”
0155208C
3/4” nap roller
cover
Manchon de rouleau à
grain de 3/4 ” (1,9 cm)
Cubierta del rodillo con
lanilla de 3/4”
0284001G
GlassMask™
GlassMask™
GlassMask™
0513030
3
10
12
Trim It™
Trim It™
Trim It™
0284112B
Roller Cleanup
Kit™
Roller Cleanup Kit™
Roller Cleanup Kit™
0284051A
5 gallon paint
adapter
Adaptateur pour
contenant à peinture
de 5 gallons (19 l)
Adaptador para pintura
de 5 gallones
0284419
Non-standard
container lid
Couvercle de
contenant spécial
Tapa de recipiente no
estándar
11
Item
Article
Articulo
Part No.
Nº de piéce
Pieza No.
English
Description
Français
Description
Español
Descripción
Quantity
Quantite
Cantidad
1
0514118
Roller core and cap*
Corps du rouleau et capuchon*
Centro y tapa del rodillo*
1
2
0155206C
3/8” nap roller cover
Manchon de rouleau à grain de 3/8 ” (1 cm)
Cubierta del rodillo con lanilla de 3/8”
1
3
0514230
Spatter guard
Garde-éclaboussures
Protección contra salpicaduras
1
4
0514150
Roller arm assembly (includes item 5)
Ensemble de bras de rouleau (inclut l’article 5)
Conjunto del brazo del rodillo (incluye el artículo 5)
1
5
0514112
Seal and O-ring*
Joint d’étanchéité et joint torique*
Sello y junta tórica*
1
6
0284136
Plunger O-rings
Joints toriques du piston
Juntas tóricas del émbolo
2
7
0284398
Locking cap
Capuchon de blocage
Tapa de sujeción
1
8
0284395
Retainer disk
Disque de retenue
Disco retenedor
1
9
0271434
Duckbill valve
Valve bec de canard
Válvula pico de pato
1
10
0284443
Standard container lid
Couvercle de contenant normal
Tapa de recipiente estándar
1
11
0284432
Fill tube
Tube de remplissage
Tubo de llenado
1
12
0284419
Non-standard container lid**
Couvercle de contenant spécial**
Tapa de recipiente no estándar**
1
* Can only be purchased together and not separately.
** Not included with all models
English
Français
Español
* Forment un ensemble et ne peuvent pas être
achetés séparément.
** Non inclus avec tous les modèles.
20
* Sólo se puede comprar junto, no por separado.
** No se incluye con todos los modelos.