Yamaha VINO 125 Owner`s manual

Yamaha VINO 125 Owner`s manual
OWNER’S MANUAL
YJ125X
LIT-11626-21-54
5YR-F8199-14_ch0cv.pmd
5YR-F8199-14
2
2007/05/21, 17:38
1
2
3
EAU10041
4
5
6
7
8
9
5YR-F8199-14_ch0cv.pmd
3
2007/05/21, 17:38
EAU10050
INTRODUCTION
EAU10090
Congratulations on your purchase of the Yamaha VINO125. This model is the result of Yamaha’s vast experience in the
production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and
reliability that have made Yamaha a leader in these fields.
1
This manual will give you an understanding of the operation, inspection, and basic maintenance of this scooter. If you have
any questions concerning the operation or maintenance of your scooter, please consult a Yamaha dealer.
The design and manufacture of this Yamaha scooter fully comply with the emissions standards for clean air applicable at the
date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the
scooter. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the
recommended maintenance schedules and operating instructions contained within this manual.
2
3
4
5
6
7
8
9
5YR-F8199-14_ch0cv.pmd
4
2007/05/21, 17:38
EAU10122
IMPORTANT MANUAL INFORMATION
EAU35821
Particularly important information is distinguished in this manual by the following notations:
Q
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
2
w
Failure to follow WARNING instructions could result in severe injury or death to the scooter
operator, a bystander, or a person inspecting or repairing the scooter.
3
cC
A CAUTION indicates special precautions that must be taken to avoid damage to the scooter.
4
NOTE:
A NOTE provides key information to make procedures easier or clearer.
1
5
6
7
8
9
NOTE:
● This manual should be considered a permanent part of this scooter and should remain with it even if the scooter is
subsequently sold.
● Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most
current product information available at the time of printing, there may be minor discrepancies between your scooter
and this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.
EWA12580
w
PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLY
AND COMPLETELY BEFORE OPERATING THIS SCOOTER. DO NOT ATTEMPT TO OPERATE THIS SCOOTER UNTIL
YOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES AND UNTIL
YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONS AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFELY ENJOY THE CAPABILITIES AND THE RELIABILITY OF THIS SCOOTER.
*Product and specifications are subject to change without notice.
5YR-F8199-14_ch0cv.pmd
5
2007/05/21, 17:38
EAU10122
IMPORTANT MANUAL INFORMATION
1
2
AFFIX DEALER
3
LABEL HERE
4
5
EAUT2190
VINO125
OWNER’S MANUAL
©2007 by Yamaha Motor Corporation, U.S.A.
1st edition, July 2007
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, U.S.A.
is expressly prohibited.
Printed in Taiwan.
P/N LIT-11626-21-54
5YR-F8199-14_ch0cv.pmd
6
2007/05/21, 17:38
6
7
8
9
EAU10210
TABLE OF CONTENTS
SAFETY INFORMATION ................... 1-1
Further safe-riding points ............... 1-4
Location of important labels ........... 1-6
1
2
3
4
5
6
7
8
9
DESCRIPTION ................................... 2-1
Left view ......................................... 2-1
Right view ....................................... 2-2
Controls and instruments ............... 2-3
INSTRUMENT AND CONTROL FUNCTIONS ................................................ 3-1
Main switch/steering lock ............... 3-1
Indicator lights ................................ 3-2
Speedometer unit ........................... 3-2
Fuel gauge ...................................... 3-2
Handlebar switches ........................ 3-3
Front brake lever ............................. 3-4
Rear brake lever ............................. 3-4
Fuel tank cap .................................. 3-4
Fuel ................................................. 3-5
Catalytic converter .......................... 3-6
Kickstarter ....................................... 3-6
Seat ................................................ 3-7
Helmet holder ................................. 3-7
Storage compartment ..................... 3-8
Carrier ............................................. 3-9
Luggage hook ................................. 3-9
Sidestand ...................................... 3-10
Ignition circuit cut-off system ........ 3-10
5YR-F8199-14_ch0cv.pmd
7
PRE-OPERATION CHECKS ............. 4-1
Pre-operation check list .................. 4-2
OPERATION AND IMPORTANT RIDING
POINTS .............................................. 5-1
Starting a cold engine .................... 5-1
Starting off ...................................... 5-2
Acceleration and deceleration ........ 5-2
Braking ........................................... 5-2
Engine break-in .............................. 5-3
Parking ........................................... 5-3
PERIODIC MAINTENANCE AND MINOR
REPAIR .............................................. 6-1
PERIODIC MAINTENANCE ........... 6-1
Owner’s tool kit ............................... 6-1
Periodic maintenance chart for the
emission control system .............. 6-3
General maintenance and lubrication
chart ............................................ 6-4
Removing and installing panels ..... 6-8
Engine oil and oil strainer ............... 6-9
Final transmission oil .................... 6-11
Air filter and V-belt case air filter
elements .................................... 6-12
Carburetor .................................... 6-14
Checking the throttle cable free
play ............................................ 6-14
Tires .............................................. 6-15
Cast wheels .................................. 6-16
Checking the front brake lever free
play ............................................ 6-17
Adjusting the rear brake lever free
play ............................................ 6-17
Checking the front brake pads and rear
brake shoes ............................... 6-18
Checking the brake fluid level ....... 6-19
Changing the brake fluid .............. 6-20
Checking and lubricating the
cables ........................................ 6-20
Checking and lubricating the throttle
grip and cable ............................ 6-20
Lubricating the front and rear brake
levers ......................................... 6-21
Checking and lubricating the
centerstand and sidestand ........ 6-21
Checking the front fork ................. 6-22
Checking the steering ................... 6-22
Checking the wheel bearings ....... 6-23
Battery .......................................... 6-23
Replacing the fuse ........................ 6-25
Replacing the headlight bulb ........ 6-25
Replacing the tail/brake light bulb 6-27
Replacing a turn signal light bulb . 6-27
Troubleshooting ............................ 6-28
Troubleshooting chart ................... 6-29
SCOOTER CARE AND STORAGE ... 7-1
Care ................................................ 7-1
Storage ........................................... 7-3
2007/05/21, 17:38
EAU10210
TABLE OF CONTENTS
SPECIFICATIONS ............................. 8-1
CONSUMER INFORMATION ............ 9-1
Identification numbers .................... 9-1
Reporting safety defects ................. 9-3
Motorcycle noise regulation ............ 9-4
Maintenance record ........................ 9-5
YAMAHA MOTOR CORPORATION,
U.S.A. RIVA LIMITED
WARRANTY ................................ 9-7
YAMAHA EXTENDED SERVICE
(Y.E.S.) ........................................ 9-9
1
2
3
4
5
6
7
8
9
5YR-F8199-14_ch0cv.pmd
8
2007/05/21, 17:38
Safety information<IXE>
Q SAFETY INFORMATION
EAU10261
1
2
3
4
5
6
7
8
9
SCOOTERS ARE SINGLE TRACK VEHICLES. THEIR SAFE USE AND OPERATION ARE DEPENDENT UPON
THE USE OF PROPER RIDING TECHNIQUES AS WELL AS THE EXPERTISE OF THE OPERATOR. EVERY
OPERATOR SHOULD KNOW THE FOLLOWING REQUIREMENTS BEFORE
RIDING THIS SCOOTER.
HE OR SHE SHOULD:
8 OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT
SOURCE ON ALL ASPECTS OF
SCOOTER OPERATION.
8 OBSERVE THE WARNINGS AND
MAINTENANCE REQUIREMENTS IN THE OWNER’S
MANUAL.
8 OBTAIN QUALIFIED TRAINING IN
SAFE AND PROPER RIDING
TECHNIQUES.
8 OBTAIN PROFESSIONAL TECHNICAL SERVICE AS INDICATED
BY THE OWNER’S MANUAL AND/
OR WHEN MADE NECESSARY
BY MECHANICAL CONDITIONS.
Safe riding
8 Always make pre-operation checks.
Careful checks may help prevent
an accident.
8 This scooter is designed to carry
the operator and passenger.
8 The failure of motorists to detect
and recognize scooters in traffic is
the predominating cause of automobile/scooter accidents. Many
accidents have been caused by an
automobile driver who did not see
the scooter. Making yourself conspicuous appears to be very effective in reducing the chance of this
type of accident.
Therefore:
9 Wear a brightly colored jacket.
9 Use extra caution when approaching and passing through
intersections, since intersections are the most likely places
for scooter accidents to occur.
9 Ride where other motorists can
see you. Avoid riding in another
motorist’s blind spot.
8 Many accidents involve inexperienced operators. In fact, many operators who have been involved in
accidents do not even have a current driver’s license.
9 Make sure that you are qualified and that you only lend your
scooter to other qualified
operators.
9 Know your skills and limits.
Staying within your limits may
help you to avoid an accident.
9 We recommend that you
practice riding your scooter
where there is no traffic until
you have become thoroughly
familiar with the scooter and all
of its controls.
8 Many accidents have been caused
by error of the scooter operator. A
typical error made by the operator
is veering wide on a turn due to
EXCESSIVE
SPEED
or
undercornering (insufficient lean
angle for the speed).
9 Always obey the speed limit
and never travel faster than
warranted by road and traffic
conditions.
1-1
5YR-F8199-14_ch1.pmd
1
2007/05/21, 17:39
Q SAFETY INFORMATION
9 Always signal before turning or
changing lanes. Make sure that
other motorists can see you.
8 The posture of the operator and
passenger is important for proper
control.
9 The operator should keep both
hands on the handlebar and
both feet on the footboard
during operation to maintain
control of the scooter.
9 The passenger should always
hold onto the operator, the seat
strap or grab bar, if equipped,
with both hands and keep both
feet on the passenger footrests.
9 Never carry a passenger unless
he or she can firmly place both
feet on the passenger footrests.
8 Never ride under the influence of
alcohol or other drugs.
8 This scooter is designed for on-road
use only. It is not suitable for offroad use.
Protective apparel
The majority of fatalities from scooter
accidents are the result of head injuries.
The use of a safety helmet is the single
most critical factor in the prevention or
reduction of head injuries.
8 Always wear an approved helmet.
8 Wear a face shield or goggles. Wind
in your unprotected eyes could contribute to an impairment of vision
which could delay seeing a hazard.
8 The use of a jacket, substantial
shoes, trousers, gloves, etc., is
effective in preventing or reducing
abrasions or lacerations.
8 Never wear loose-fitting clothes,
otherwise they could catch on the
control levers or wheels and cause
injury or an accident.
8 Never touch the engine or exhaust
system during or after operation.
They become very hot and can
cause burns. Always wear protective clothing that covers your legs,
ankles, and feet.
8 Passengers should also observe
the above precautions.
original equipment, may render the
scooter unsafe for use and may cause
severe personal injury. Modifications
may also make your scooter illegal to
use.
Loading and accessories
Adding accessories or cargo to your
scooter can adversely affect stability
and handling if the weight distribution of
the scooter is changed. To avoid the
possibility of an accident, use extreme
caution when adding cargo or accessories to your scooter. Use extra care when
riding a scooter that has added cargo or
accessories. Here are some general
guidelines to follow if loading cargo or
adding accessories to your scooter:
Loading
The total weight of the operator, passenger, accessories and cargo must not
exceed the maximum load limit.
Maximum load:
144 kg (317 lb)
Modifications
Modifications made to this scooter not
approved by Yamaha, or the removal of
1-2
5YR-F8199-14_ch1.pmd
2
2007/05/21, 17:39
1
2
3
4
5
6
7
8
9
Q SAFETY INFORMATION
1
2
3
4
5
6
7
8
9
When loading within this weight limit,
keep the following in mind:
8 Cargo and accessory weight should
be kept as low and close to the
scooter as possible. Make sure to
distribute the weight as evenly as
possible on both sides of the
scooter to minimize imbalance or
instability.
8 Shifting weights can create a sudden imbalance. Make sure that accessories and cargo are securely
attached to the scooter before riding.
Check accessory mounts and
cargo restraints frequently.
8 Never attach any large or heavy
items to the handlebar, front fork,
or front fender. Such items can create unstable handling or a slow
steering response.
Accessories
Genuine Yamaha accessories have
been specifically designed for use on
this scooter. Since Yamaha cannot test
all other accessories that may be available, you must personally be responsible
for the proper selection, installation and
use of non-Yamaha accessories. Use
extreme caution when selecting and installing any accessories.
Keep the following guidelines in mind,
as well as those provided under “Loading” when mounting accessories.
8 Never install accessories or carry
cargo that would impair the performance of your scooter. Carefully
inspect the accessory before using it to make sure that it does not
in any way reduce ground clearance or cornering clearance, limit
suspension travel, steering travel
or control operation, or obscure
lights or reflectors.
9 Accessories fitted to the
handlebar or the front fork area
can create instability due to
improper weight distribution or
aerodynamic changes. If
accessories are added to the
handlebar or front fork area,
they must be as lightweight as
possible and should be kept to
a minimum.
9 Bulky or large accessories may
seriously affect the stability of
the scooter due to aerodynamic
effects. Wind may attempt to
lift the scooter, or the scooter
may become unstable in cross
winds. These accessories may
also cause instability when
passing or being passed by
large vehicles.
9 Certain accessories can
displace the operator from his
or her normal riding position.
This improper position limits
the freedom of movement of
the operator and may limit
control ability, therefore, such
accessories are not recommended.
8 Use caution when adding electrical
accessories. If electrical accessories exceed the capacity of the
scooter’s electrical system an electric failure could result, which could
cause a dangerous loss of lights or
engine power.
Gasoline and exhaust gas
8 GASOLINE IS HIGHLY FLAMMABLE:
9 Always turn the engine off
when refueling.
1-3
5YR-F8199-14_ch1.pmd
3
2007/05/21, 17:39
Safe-riding points<IXE>
Q SAFETY INFORMATION
9 Take care not to spill any
gasoline on the engine or
exhaust system when refueling.
9 Never refuel while smoking or
in the vicinity of an open flame.
8 Never start the engine or let it run
for any length of time in a closed
area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a
short time. Always operate your
scooter in an area that has adequate
ventilation.
8 Always turn the engine off before
leaving the scooter unattended and
remove the key from the main
switch. When parking the scooter,
note the following:
9 The engine and exhaust
system may be hot, therefore,
park the scooter in a place
where pedestrians or children
are not likely to touch these hot
areas.
9 Do not park the scooter on a
slope or soft ground, otherwise
it may fall over.
9 Do not park the scooter near a
flammable source (e.g., a
kerosene heater, or near an
open flame), otherwise it could
catch fire.
8 If you should swallow any gasoline,
inhale a lot of gasoline vapor, or
allow gasoline to get into your eyes,
see your doctor immediately. If any
gasoline spills on your skin or clothing, immediately wash the affected
area with soap and water and
change your clothes.
EAU10350
Further safe-riding points
8 Make sure to signal clearly when
making turns.
8 Braking can be extremely difficult
on a wet road. Avoid hard braking,
because the scooter could slide.
Apply the brakes slowly when stopping on a wet surface.
8 Slow down as you approach a corner or turn. Once you have completed a turn, accelerate slowly.
8 Be careful when passing parked
cars. A driver might not see you and
open a door in your path.
8 Railroad crossings, streetcar rails,
iron plates on road construction
sites, and manhole covers become
extremely slippery when wet. Slow
down and cross them with caution.
Keep the scooter upright, otherwise
it could slide out from under you.
8 The brake lining could get wet when
you wash the scooter. After washing the scooter, check the brakes
before riding.
8 Always wear a helmet, gloves, trousers (tapered around the cuff and
ankle so they do not flap), and a
1-4
5YR-F8199-14_ch1.pmd
4
2007/05/21, 17:39
1
2
3
4
5
6
7
8
9
Q SAFETY INFORMATION
1
2
3
bright colored jacket.
8 Do not carry too much luggage on
the scooter. An overloaded scooter
is unstable. Use a strong cord to
secure any luggage to the carriers.
A loose load will affect the stability
of the scooter and could divert your
attention from the road. (See page
1-1.)
4
5
6
7
8
9
1-5
5YR-F8199-14_ch1.pmd
5
2007/05/21, 17:39
Labels, location of<IXE>
Q SAFETY INFORMATION
EAU10381
Location of important labels
Please read the following important labels carefully before operating this vehicle.
1
2
3
1
2 3
4
6
5
5
6
7
4
8
9
1-6
5YR-F8199-14_ch1.pmd
6
2007/05/21, 17:39
Q SAFETY INFORMATION
1
4
2
5
3
6
1
2
3
4
5
6
7
8
9
1-7
5YR-F8199-14_ch1.pmd
7
2007/05/21, 17:39
Q SAFETY INFORMATION
1
2
3
4
5
6
7
8
9
1-8
5YR-F8199-14_ch1.pmd
8
2007/05/21, 17:39
Part locations<IXE>
EAU10400
DESCRIPTION
EAU10410
Left view
1
2
2
3
4
1
3
4
5
5
6
6
7
9
8
9
1.
2.
3.
4.
5.
6.
7.
8.
9.
8
7
Front turn signal light (page 6-27)
Luggage hook (page 3-9)
Helmet holder (page 3-7)
Storage compartment (page 3-8)
Rear turn signal light (page 6-27)
Brake lever free play adjusting nut (page 6-17)
Kickstarter (page 3-6)
Air filter (page 6-12)
Battery (page 6-23)
2-1
5YR-F8199-14_ch2.pmd
1
2007/05/21, 17:39
DESCRIPTION
EAU10420
Right view
1
2 3
4
5
1
6
2
3
4
5
6
7
9
8
7
8
1.
2.
3.
4.
5.
6.
7.
8.
9.
Tail/brake light (page 6-27)
Carrier (page 3-9)
Fuel tank cap (page 3-4)
Seat (page 3-7)
Front brake master cylinder (page 6-19)
Headlight (page 6-25)
Spark plug (page 6-8)
Centerstand (page 6-21)
Muffler
9
2-2
5YR-F8199-14_ch2.pmd
2
2007/05/21, 17:39
DESCRIPTION
EAU10430
Controls and instruments
1
1
2
3
4
2
3
5
4
5
7
8
6
7
8
9
1.
2.
3.
4.
5.
6.
7.
8.
Rear brake lever (page 3-4)
Left handlebar switches (page 3-3)
Speedometer unit (page 3-2)
Right handlebar switches (page 3-3)
Front brake lever (page 3-4)
Throttle grip (page 6-14)
Main switch/steering lock (page 3-1)
Fuel gauge (page 3-2)
2-3
5YR-F8199-14_ch2.pmd
3
2007/05/21, 17:39
6
Main switch/steering lock<IXE>
EAU10444
INSTRUMENT AND CONTROL FUNCTIONS
EAU10460
Main switch/steering lock
EAU10660
OFF
All electrical systems are off. The key
can be removed.
EAU10680
LOCK
The steering is locked, and all electrical
systems are off. The key can be removed.
To lock the steering
To unlock the steering
1
1
2
2
3
ZAUM00**
4
ZAUM00**
1. Turn.
2. Release.
1
The main switch/steering lock controls
the ignition and lighting systems, and is
used to lock the steering. The various
positions are described below.
Push the key in, and then turn it to “OFF”
while still pushing it.
w
ZAUM00**
1. Push.
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF” position, and then turn it to “LOCK”
while still pushing it.
3. Remove the key.
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving,
otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident. Make
sure that the vehicle is stopped before turning the key to “OFF” or
“LOCK”.
3-1
5YR-F8199-14_ch3.pmd
1
6
EWA10060
EAU10530
ON
All electrical circuits are supplied with
power, the taillight comes on, and the
engine can be started. The key cannot
be removed.
NOTE:
The headlight and meter lighting come
on automatically when the engine is
started.
5
2007/05/21, 17:40
7
8
9
Indicator lights<IXE>
Turn signal indicator light<IXE>
High beam indicator light<IXE>
Speedometer unit<IXE>
Fuel gauge<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU10980
Indicator lights
1
EAUT1820
Speedometer unit
2
40
1
50
30
60
80
60
40
20
2
60
40
20
100
20
80
0
0
MPH
70
120
10
0
0
60
80
70
120
50
30
100
20
10
1
1
40
2
EAU12150
Fuel gauge
80
MPH
3
4
5
ZAUM00**
ZAUM00**
1. High beam indicator light“&”
2. Turn signal indicator lights“4”and 6”
EAU11020
6
7
4 6”
Turn signal indicator light “4
This indicator light flashes when the turn
signal switch is pushed to the left or right.
EAU11080
8
9
&”
High beam indicator light “&
This indicator light comes on when the
high beam of the headlight is switched
on.
ZAUM00**
1. Speedometer
2. Odometer
1. Fuel gauge
The speedometer unit is equipped with
a speedometer and an odometer. The
speedometer shows the riding speed.
The odometer shows the total distance
traveled.
The fuel gauge indicates the amount of
fuel in the fuel tank. The needle moves
towards “E” (Empty) as the fuel level
decreases. When the needle reaches the
red line, refuel as soon as possible.
NOTE:
Do not allow the fuel tank to empty itself completely.
3-2
5YR-F8199-14_ch3.pmd
2
2007/05/21, 17:40
Handlebar switches<IXE>
Dimmer switch<IXE>
Turn signal switch<IXE>
Horn switch<IXE>
Engine stop switch<IXE>
Start switch<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU12347
Handlebar switches
EAU12500
Right
*”
Horn switch “*
Press this switch to sound the horn.
Left
1
1
EAU12660
#/$
$”
Engine stop switch “#
Set this switch to “#” before starting
the engine. Set this switch to “$” to stop
the engine in case of an emergency, such
as when the motorcycle overturns or
when the throttle cable is stuck.
2
2
3
ZAUM00**
1. Engine stop switch “#/$“
2. Start switch “START”
ZAUM00**
1. Dimmer switch “%/&“
2. Turn signal switch “4/6”
3. Horn switch “*”
EAU12400
&/%
%”
Dimmer switch “&
Set this switch to “&” for the high beam
and to “%” for the low beam.
EAU12460
4/6
6”
Turn signal switch “4
To signal a right-hand turn, push this
switch to “4”. To signal a left-hand turn,
push this switch to “6”. When released,
the switch returns to the center position.
To cancel the turn signal lights, push the
switch in after it has returned to the center position.
3
2
3
EAU12700
4
Start switch “START”
Push this switch while applying the front
or rear brake to crank the engine with
the starter.
5
ECA10050
6
See page 5-1 for starting instructions
prior to starting the engine.
7
cC
3-3
5YR-F8199-14_ch3.pmd
1
2007/05/21, 17:40
8
9
Brake lever, front<IXE>
Brake lever, rear<IXE>
Fuel tank cap<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU12900
Front brake lever
EAU12950
Rear brake lever
1
1
1
EAU32483
Fuel tank cap
2
1
2
3
4
5
6
7
ZAUM00**
ZAUM00**
ZAUM00**
1. Front brake lever
1. Rear brake lever
1. Fuel tank cap lock cover
2. Match marks
The front brake lever is located on the
right handlebar grip. To apply the front
brake, pull this lever toward the handlebar grip.
The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the handlebar grip.
8
9
3-4
5YR-F8199-14_ch3.pmd
4
To remove the fuel tank cap
Slide the lock cover open, insert the key
into the lock, and then turn it 1/4 turn
clockwise. The lock will be released and
the fuel tank cap can be removed.
To install the fuel tank cap
1. Insert the fuel tank cap into the tank
opening with the key inserted in the
lock and with the marks on the cap
and tank aligned.
2. Turn the key counterclockwise to
the original position, remove it, and
then close the lock cover.
2007/05/21, 17:40
Fuel<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
NOTE:
The fuel tank cap cannot be installed
unless the key is in the lock. In addition, the key cannot be removed if the
cap is not properly installed and locked.
EAU13211
Fuel
deteriorate painted surfaces or plastic parts.
1
EAU36080
Recommended fuel:
UNLEADED GASOLINE ONLY
Fuel tank capacity:
4.7 L (1.24 US gal) (1.03 Imp.gal)
EWA10130
w
ECA11400
cC
ZAUM00**
1. Fuel tank filler tube
Make sure that there is sufficient fuel in
the tank. Fill the fuel tank to the bottom
of the filler tube as shown.
EWA10880
w
8 Do not overfill the fuel tank, otherwise it may overflow when the
fuel warms up and expands.
Avoid spilling fuel on the hot
engine.
ECA10070
cC
Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts, such
as the valves and piston rings, as well
as to the exhaust system.
Your Yamaha engine has been designed
to use regular unleaded gasoline with a
pump octane number [(R+M)/2] of 86 or
higher, or a research octane number of
91 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand
or premium unleaded fuel. Use of unleaded fuel will extend spark plug life
and reduce maintenance costs.
Immediately wipe off spilled fuel with
a clean, dry, soft cloth, since fuel may
3-5
5
2
3
Make sure that the fuel tank cap is
properly installed before riding.
5YR-F8199-14_ch3.pmd
1
2007/05/21, 17:40
4
5
6
7
8
9
Catalytic converter<IXE>
Kickstarter<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
Gasohol
There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used if the ethanol content
does not exceed 10%. Gasohol containing methanol is not recommended by
Yamaha because it can cause damage
to the fuel system or vehicle performance problems.
EAU13431
Catalytic converter
EAU13680
Kickstarter
This model is equipped with a catalytic
converter in the exhaust system.
EWA10860
w
The exhaust system is hot after operation. Make sure that the exhaust
system has cooled down before doing any maintenance work.
1
4
ECA10700
ZAUM00**
cC
The following precautions must be
observed to prevent a fire hazard or
other damages.
8 Use only unleaded gasoline. The
use of leaded gasoline will cause
unrepairable damage to the catalytic converter.
8 Never park the vehicle near possible fire hazards such as grass
or other materials that easily
burn.
8 Do not allow the engine to idle
too long.
5
6
7
8
9
1. Kickstarter
To start the engine, fold out the kickstarter
lever, move it down lightly with your foot
until the gears engage, and then push it
down smoothly but forcefully.
3-6
5YR-F8199-14_ch3.pmd
6
2007/05/21, 17:40
Seat<IXE>
Helmet holder<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU13932
Seat
To open the seat
1. Place the scooter on the
centerstand.
2. Insert the key into the main switch,
and then turn it counterclockwise
to “OPEN”.
2. Remove the key from the main
switch if the scooter will be left unattended.
NOTE:
Make sure that the seat is properly secured before riding.
EAU14300
Helmet holder
1
1
2
3
4
ZAUM00**
1. Helmet holder
5
The helmet holder is located under the
seat.
To secure a helmet to the helmet
holder
1. Open the seat. (See page 3-7.)
2. Attach the helmet to the helmet
holder, and then securely close the
seat.
ZAUM00**
NOTE:
Do not push inward when turning the key.
EWA10160
3. Fold the seat up.
w
Never ride with a helmet attached to
the helmet holder, since the helmet
may hit objects, causing loss of control and possibly an accident.
To close the seat
1. Fold the seat down, and then push
it down to lock it in place.
3-7
5YR-F8199-14_ch3.pmd
7
2007/05/21, 17:40
6
7
8
9
Storage compartment<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
1
To release the helmet from the helmet holder
Open the seat, remove the helmet from
the helmet holder, and then close the
seat.
EAU14510
Storage compartment
1
2
3
4
ZAUM00**
1. Storage compartment
5
There is a storage compartment under
the seat. (See page 3-7.)
6
EWA10960
w
7
8 Do not exceed the load limit of 5
kg (11 lb) for the storage compartment.
8 Do not exceed the maximum
load of 144 kg (317 lb) for the vehicle.
8
9
ECA10080
cC
Keep the following points in mind
when using the storage compartment.
8 Since the storage compartment
accumulates heat when exposed
to the sun, do not store anything
susceptible to heat inside it.
8 To avoid humidity from spreading through the storage compartment, wrap wet articles in a plastic bag before storing them in the
compartment.
8 Since the storage compartment
may get wet while the scooter is
being washed, wrap any articles
stored in the compartment in a
plastic bag.
8 Do not keep anything valuable or
breakable in the storage compartment.
To store a helmet in the storage compartment, place the helmet upside-down
with the front facing forward.
NOTE:
8 Some helmets cannot be stored in
the storage compartment because
of their size or shape.
8 Do not leave your scooter unat-
3-8
5YR-F8199-14_ch3.pmd
8
2007/05/21, 17:40
Carrier<IXE>
Luggage hook<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
tended with the seat open.
EAU15110
Carrier
EAUT1070
Luggage hook
1
1
1
2
3
ZAUM00**
4
ZAUM00**
1. Rear carrier
1. Luggage hook
EWA10170
w
EWAT1030
5
w
8 Do not exceed the load limit of 3
kg (7 lb) for the carrier.
8 Do not exceed the maximum
load of 144 kg (317 lb) for the vehicle.
8 Do not exceed the load limit of 3
kg (7 lb) for the luggage hook.
8 Do not exceed the maximum
load of 144 kg (317 lb) for the vehicle.
6
7
8
9
3-9
5YR-F8199-14_ch3.pmd
9
2007/05/21, 17:40
Sidestand<IXE>
Ignition circuit cut-off system<IXE>
INSTRUMENT AND CONTROL FUNCTIONS
EAU15301
Sidestand
1
2
3
4
The sidestand is located on the left side
of the frame. Raise the sidestand or lower
it with your foot while holding the motorcycle upright.
NOTE:
The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation of
the ignition circuit cut-off system.)
5
have a Yamaha dealer repair it if it
does not function properly.
EWA10240
w
6
7
8
9
The vehicle must not be ridden with
the sidestand down, or if the
sidestand cannot be properly moved
up (or does not stay up), otherwise
the sidestand could contact the
ground and distract the operator, resulting in a possible loss of control.
Yamaha’s ignition circuit cut-off system has been designed to assist the
operator in fulfilling the responsibility of raising the sidestand before
starting off. Therefore, check this system regularly as described below and
EAU15372
Ignition circuit cut-off system
The ignition circuit cut-off system (comprising the sidestand switch and brake
light switches) has the following functions.
8 It prevents star ting when the
sidestand is up, but neither brake
is applied.
8 It prevents starting when either
brake is applied, but the sidestand
is still down.
8 It cuts the running engine when the
sidestand is moved down.
Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.
EWA10250
w
If a malfunction is noted, have a
Yamaha dealer check the system before riding.
3-10
5YR-F8199-14_ch3.pmd
10
2007/05/21, 17:40
INSTRUMENT AND CONTROL FUNCTIONS
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the key on.
4. Keep the front or rear brake applied.
5. Push the start switch.
Does the engine start?
NO
NOTE:
This check is most reliable if performed with a warmedup engine.
1
2
The sidestand switch may be defective.
The scooter should not be ridden until checked by a
Yamaha dealer.
YES
With the engine still off:
6. Move the sidestand up.
7. Keep the front or rear brake applied.
8. Push the start switch.
Does the engine start?
YES
The brake switch may be defective.
The scooter should not be ridden until checked by a
Yamaha dealer.
NO
NO
3-11
11
6
7
8
The sidestand switch may be defective.
The scooter should not be ridden until checked by a
Yamaha dealer.
The system is OK. The scooter can be ridden.
5YR-F8199-14_ch3.pmd
4
5
With the engine still running:
9. Move the sidestand down.
Does the engine stall?
YES
3
2007/05/21, 17:40
9
EAU15580
PRE-OPERATION CHECKS
EAU15593
1
2
The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly,
even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss
of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual inspection, to check the following points before each ride.
NOTE:
Pre-operation checks should be made each time the vehicle is used. Such an inspection can be accomplished in a very short
time; and the added safety it assures is more than worth the time involved.
3
EWA11150
4
w
If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operating
the vehicle.
5
6
7
8
9
4-1
5YR-F8199-14_ch4.pmd
1
2007/05/21, 17:40
Pre-operation check list<IXE>
PRE-OPERATION CHECKS
EAU15605
Pre-operation check list
ITEM
CHECKS
PAGE
Fuel
• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.
3-5
Engine oil
• Check oil level in engine.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.
6-9
Final transmission oil
• Check vehicle for oil leakage.
6-11
Front brake
•
•
•
•
•
•
•
Check operation.
If soft or spongy, have Yamaha dealer bleed hydraulic system.
Check brake pads for wear.
Replace if necessary.
Check fluid level in reservoir.
If necessary, add recommended brake fluid to specified level.
Check hydraulic system for leakage.
6-18, 6-19
Rear brake
•
•
•
•
Check operation.
Lubricate cable if necessary.
Check lever free play.
Adjust if necessary.
6-17~6-18
Throttle grip
• Make sure that operation is smooth.
• Check free play.
• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and
grip housing.
6-14, 6-20
Wheels and tires
•
•
•
•
6-15, 6-16
Brake levers
• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.
2
2
3
4
5
6
Check for damage.
Check tire condition and tread depth.
Check air pressure.
Correct if necessary.
7
6-21
4-2
5YR-F8199-14_ch4.pmd
1
2007/05/21, 17:40
8
9
PRE-OPERATION CHECKS
ITEM
CHECKS
• Make sure that operation is smooth.
• Lubricate pivot if necessary.
Centerstand, sidestand
1
2
3
PAGE
6-21
Chassis fasteners
• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.
-
Instruments, lights, signals
and switches
• Check operation.
• Correct if necessary.
-
Engine stop switch
• Check operation.
3-3
Sidestand switch
• Check operation of ignition circuit cut-off system.
• If system is defective, have Yamaha dealer check vehicle.
3-10
4
5
6
7
8
9
4-3
5YR-F8199-14_ch4.pmd
3
2007/05/21, 17:40
Starting a cold engine<IXE>
EAU15941
OPERATION AND IMPORTANT RIDING POINTS
EAU15980
EWA10870
w
EAU16592
Starting a cold engine
ECA10250
8 Become thoroughly familiar with
all operating controls and their
functions before riding. Consult
a Yamaha dealer regarding any
control or function that you do
not thoroughly understand.
8 Never start the engine or operate
it in a closed area for any length
of time. Exhaust fumes are poisonous, and inhaling them can
cause loss of consciousness and
death within a short time. Always
make sure that there is adequate
ventilation.
8 For safety, always start the engine
with the centerstand down.
cC
See page 5-3 for engine break-in instructions prior to operating the vehicle for the first time.
In order for the ignition circuit cut-off
system to enable starting, the sidestand
must be up.
EWA10290
w
8 Before starting the engine, check
the function of the ignition circuit cut-off system according to
the procedure described on page
3-10.
8 Never ride with the sidestand
down.
NOTE:
If the engine does not start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to preserve the battery. Do not crank the engine more than 10 seconds on any one
attempt. If the engine does not start, try
with the throttle open 1/8 turn.
1
2
3
ECA11130
4
For maximum engine life, always
warm the engine up before starting
off. Never accelerate hard when the
engine is cold!
5
cC
6
7
8
1. Turn the key to “ON” and make sure
that the engine stop switch is set
to “#”.
2. Close the throttle completely.
3. Start the engine by pushing the
start switch while applying the front
or rear brake.
5-1
5YR-F8199-14_ch5.pmd
1
2007/05/21, 17:41
9
Starting off<IXE>
Acceleration and deceleration<IXE>
Braking<IXE>
OPERATION AND IMPORTANT RIDING POINTS
EAU16770
Starting off
1
EAU16780
Acceleration and deceleration
NOTE:
Before starting off, allow the engine to
warm up.
50
60
80
100
b
3
20
4
70
120
10
EWA10300
0
0
1. While pulling the rear brake lever
with your left hand and holding the
carrier with your right hand, push
the scooter off the centerstand.
(b)
60
40
20
2
w
80
MPH
(a)
ZAUM00**
The speed can be adjusted by opening
and closing the throttle. To increase the
speed, turn the throttle grip in direction
(a). To reduce the speed, turn the throttle
grip in direction (b).
5
6
7
ZAUM00**
8
9
1. Close the throttle completely.
2. Apply both front and rear brakes simultaneously while gradually increasing the pressure.
a 40
30
EAU16792
Braking
2. Sit astride the seat, and then adjust the rear view mirrors.
3. Switch the turn signal on.
4. Check for oncoming traffic, and
then slowly turn the throttle grip (on
the right) in order to take off.
5. Switch the turn signal off.
8 Avoid braking hard or suddenly
(especially when leaning over to
one side), otherwise the scooter
may skid or overturn.
8 Railroad crossings, streetcar
rails, iron plates on road construction sites, and manhole covers become extremely slippery
when wet. Therefore, slow down
when approaching such areas
and cross them with caution.
8 Keep in mind that braking on a
wet road is much more difficult.
8 Ride slowly down a hill, as braking downhill can be very difficult.
5-2
5YR-F8199-14_ch5.pmd
2
2007/05/21, 17:41
Engine break-in<IXE>
Parking<IXE>
OPERATION AND IMPORTANT RIDING POINTS
EAU16830
Engine break-in
There is never a more important period
in the life of your engine than the period
between 0 and 1000 km (600 mi). For
this reason, you should read the following material carefully.
the engine oil must be changed, and
the oil filter element and the oil
strainer cleaned.
EAU17212
Parking
When parking, stop the engine, and then
remove the key from the main switch.
1000 km (600 mi) and beyond
The vehicle can now be operated normally.
1
2
ECA10270
Since the engine is brand new, do not
put an excessive load on it for the first
1000 km (600 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances. During this period, prolonged full-throttle
operation or any condition that might
result in engine overheating must be
avoided.
cC
3
If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.
4
5
6
7
EAU16990
0~500 km (0~300 mi)
Avoid prolonged operation above 1/3
throttle.
8
500~1000 km (300~600 mi)
Avoid prolonged operation above 1/2
throttle.
9
EWA10310
ECA11500
w
cC
8 Since the engine and exhaust
system can become very hot,
After 1000 km (600 mi) of operation,
5-3
5YR-F8199-14_ch5.pmd
3
2007/05/21, 17:41
OPERATION AND IMPORTANT RIDING POINTS
1
2
park in a place where pedestrians or children are not likely to
touch them.
8 Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn.
ECA10380
3
cC
4
Never park in an area where there are
fire hazards such as grass or other
flammable materials.
5
6
7
8
9
5-4
5YR-F8199-14_ch5.pmd
4
2007/05/21, 17:41
Maintenance, periodic<IXE>
Tool kit<IXE>
EAU17224
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU17231
Safety is an obligation of the owner.
Periodic inspection, adjustment and lubrication will keep your vehicle in the
safest and most efficient condition possible. The most important points of motorcycle inspection, adjustment, and lubrication are explained on the following
pages.
Maintenance, replacement, or repair
of the emission control devices and
systems may be performed by any
repair establishment or individual that
is certified (if applicable).
EWA10320
w
If you are not familiar with maintenance work, have a Yamaha dealer do
it for you.
EAU17301
PERIODIC MAINTENANCE
EAU17370
Owner’s tool kit
PROPER PERIODIC MAINTENANCE
OF YOUR VEHICLE IS IMPORTANT IN
ORDER TO ENJOY LONG, PLEASURABLE SERVICE. ESPECIALLY IMPORTANT ARE THE MAINTENANCE SERVICES RELATED TO EMISSIONS CONTROL. THESE CONTROLS NOT ONLY
FUNCTION TO ENSURE CLEANER
AIR, BUT ARE ALSO VITAL TO
PROPER ENGINE OPERATION AND
MAXIMUM PERFORMANCE. IN THE
FOLLOWING PERIODIC MAINTENANCE CHARTS, THE SERVICES
RELATED TO EMISSIONS CONTROL
ARE GROUPED SEPARATELY. THESE
SERVICES REQUIRE SPECIALIZED
DATA, KNOWLEDGE, AND EQUIPMENT. YAMAHA DEALERS ARE
TRAINED AND EQUIPPED TO PERFORM THESE PARTICULAR SERVICES.
1
1
3
ZAUM00**
1. Owner’s tool kit
The owner’s tool kit is located under the
seat. (See page 3-7.)
The service information included in this
manual and the tools provided in the
owner’s tool kit are intended to assist
you in the performance of preventive
maintenance and minor repairs. However, additional tools such as a torque
wrench may be necessary to perform
certain maintenance work correctly.
NOTE:
If you do not have the tools or experience required for a particular job, have
a Yamaha dealer perform it for you.
6-1
5YR-F8199-14_ch6.pmd
1
2
2007/05/24, 19:58
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
EWA10340
w
1
2
Modifications not approved by
Yamaha may cause loss of performance, excessive emissions, and render the vehicle unsafe for use. Consult a Yamaha dealer before attempting any changes.
3
4
5
6
7
8
9
6-2
5YR-F8199-14_ch6.pmd
2
2007/05/24, 19:58
Maintenance, emission control system<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU17560
Periodic maintenance chart for the emission control system
INITIAL
NO.
ITEM
ROUTINE
600 mi
(1,000 km)
or
1
month
ODOMETER READING
2,000 mi
(4,000 km)
or
6
months
4,000 mi
6,000 mi
8,000 mi
10,000 mi
(7,000 km) (10,000 km) (13,000 km) (16,000 km)
or
or
or
or
12
18
24
30
months
months
months
months
Fuel line
• Check fuel and vacuum hoses for
cracks or damage.
• Replace if necessary.
√
√
√
√
√
2
Spark plug
• Check condition.
• Adjust gap and clean.
• Replace at 4000 mi (7000 km) or
12 months and thereafter every
4000 mi (6000 km) or 12 months.
√
Replace.
√
Replace.
√
3
*
Valve clearance
• Check and adjust valve clearance
when engine is cold.
√
√
√
√
√
4
*
Crankcase breather
system
• Check breather hose for cracks or
damage.
• Replace if necessary.
√
√
√
√
√
5
*
Idle speed
• Check and adjust engine idle
speed.
√
√
√
√
√
6
*
Exhaust system
• Check for leakage.
• Tighten if necessary.
• Replace gasket(s) if necessary.
√
√
√
√
√
7
*
Air induction system
• Check the air cut-off valve, reed
valve, and hose for damage.
• Replace any damaged parts.
√
√
√
√
√
1
*
3
4
6
√
6-3
3
2
5
√
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
5YR-F8199-14_ch6.pmd
1
2007/05/24, 19:58
7
8
9
Maintenance and lubrication, periodic<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU32125
General maintenance and lubrication chart
INITIAL
1
NO.
ITEM
ROUTINE
2
1
3
2
4
5
6
7
* Air filter element
V-belt case air filter
element
600 mi
(1,000 km)
or
1
month
ODOMETER READING
2,000 mi
(4,000 km)
or
6
months
10,000 mi
8,000 mi
6,000 mi
4,000 mi
(7,000 km) (10,000 km) (13,000 km) (16,000 km)
or
or
or
or
30
24
18
12
months
months
months
months
• Replace.
—
—
—
—
—
• Clean
—
—
—
—
—
3
* Front brake
• Check operation.
• Adjust cable and replace brake
shoes if necessary.
—
—
—
—
—
—
4
* Rear brake
• Check operation.
• Adjust cable and replace brake
shoes if necessary.
—
—
—
—
—
—
5
* Wheels
• Check runout and for damage.
• Replace if necessary.
—
—
—
—
—
6
* Tires
• Check tread depth and for damage.
• Replace if necessary.
• Check air pressure.
• Correct if necessary.
—
—
—
—
—
7
* Wheel bearings
• Check bearings for smooth
operation.
• Replace if necessary.
—
—
—
—
—
* Steering bearings
• Check bearing assemblies for
looseness.
• Moderately repack with lithiumsoap-based grease every 8000 mi
(13000 km) or 24 months.
—
—
—
Repack.
—
8
9
8
—
6-4
5YR-F8199-14_ch6.pmd
4
2007/05/24, 19:58
PERIODIC MAINTENANCE AND MINOR REPAIR
INITIAL
NO.
9
ITEM
ROUTINE
* Chassis fasteners
600 mi
(1,000 km)
or
1
month
ODOMETER READING
2,000 mi
(4,000 km)
or
6
months
10,000 mi
8,000 mi
6,000 mi
4,000 mi
(7,000 km) (10,000 km) (13,000 km) (16,000 km)
or
or
or
or
30
24
18
12
months
months
months
months
• Check all chassis fitting and
fasteners.
• Correct if necessary.
—
—
—
—
—
2
3
10
Front brake lever
pivot shaft
• Apply silicone grease lightly.
—
—
—
—
—
11
Rear brake lever
pivot shaft
• Apply lithium-soap-based grease
(all-purpose grease) lightly.
—
—
—
—
—
12
Centerstand and
sidestand pivots
• Check operation.
• Apply lithium-soap-based grease
(all-purpose grease) lightly.
—
—
—
—
—
13
• Check operation and replace if
necessary.
* Sidestand switch
—
—
—
—
—
—
—
—
—
—
6
*
• Check operation and for oil
leakage.
• Replace if necessary.
—
*
Shock absorber
assembly
• Check operation and for oil
leakage.
• Replace if necessary.
—
16
Engine oil
• Change (warm engine before
draining).
• Check oil level and vehicle for oil
leakage.
—
17
Engine oil filter
element
• Clean.
—
—
—
18
Engine oil strainer
• Clean.
—
—
—
15
7
—
5
—
—
—
8
—
—
6-5
5YR-F8199-14_ch6.pmd
4
5
Front fork
14
1
2007/05/24, 19:58
—
—
—
9
PERIODIC MAINTENANCE AND MINOR REPAIR
INITIAL
NO.
ITEM
ROUTINE
1
2
20
3
Final transmission
oil
19
* V-belt
*
22
*
• Check operation and free play.
• Adjust the throttle cable free play if
Throttle grip housing
necessary.
and cable
• Lubricate the throttle grip housing
and cable.
23
* switches
21
5
7
Lights, signals and
ODOMETER READING
2,000 mi
(4,000 km)
or
6
months
—
• Check operation.
• Adjust headlight beam.
10,000 mi
8,000 mi
6,000 mi
4,000 mi
(7,000 km) (10,000 km) (13,000 km) (16,000 km)
or
or
or
or
30
24
18
12
months
months
months
months
—
• Replace.
Front and rear brake
• Check operation.
switches
4
6
• Check vehicle for oil leakage.
• Change.
600 mi
(1,000 km)
or
1
month
—
Every 1200 mi (18000 km)
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
NOTE:
From 12000 mi (19000 km) or 36 months, repeat the maintenance intervals starting from 4000 mi (7000 km) or 12 months.
8
9
6-6
5YR-F8199-14_ch6.pmd
6
2007/05/24, 19:58
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU17620
NOTE:
8 The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
Hydraulic brake system
9 When disassembling the master cylinder or caliper cylinder, always replace the brake fluid. Check the brake fluid
level regularly and fill as required.
9 Replace the oil seals on the inner parts of the master cylinder and caliper cylinder every two years.
9 Replace the brake hoses every four years or if cracked or damaged.
1
2
3
4
5
6
7
8
9
6-7
5YR-F8199-14_ch6.pmd
7
2007/05/24, 19:58
Panels, removing and installing<IXE>
Spark plug, checking<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU18771
1
2
EAUT1831
2
Removing and installing panels
Checking the spark plug
The spark plug is an important engine
component, which is easy to check.
Since heat and deposits will cause any
spark plug to slowly erode, the spark
plug should be removed and checked in
accordance with the periodic maintenance and lubrication chart. In addition,
the condition of the spark plug can reveal the condition of the engine.
1
The panels shown need to be removed
to perform some of the maintenance
jobs described in this chapter. Refer to
this section each time a panel needs to
be removed and installed.
3
ZAUM00**
1. Panel A
2. Screw
4
To remove the spark plug
1. Remove panel A. (See page 6-8.)
2. Remove the spark plug cap.
5
2
1
6
2
1
ZAUM00**
7
8
1. Panel A
2. Panel B
1
ZAUM00**
EAUT1660
9
Panels A and B
To remove one of the panels
Remove the screws, and then pull the
panel off as shown.
1. Panel B
2. Screw
ZAUM00**
To install the panel
Place the panel in the original position,
and then install the screws.
1. Spark plug cap
3. Remove the spark plug as shown,
with the spark plug wrench included
6-8
5YR-F8199-14_ch6.pmd
8
2007/05/24, 19:58
Engine oil and oil strainer<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
in the owner’s tool kit.
To check the spark plug
1. Check that the porcelain insulator
around the center electrode of the
spark plug is a medium-to-light tan
(the ideal color when the vehicle is
ridden normally).
NOTE:
If the spark plug shows a distinctly different color, the engine could be operating improperly. Do not attempt to diagnose such problems yourself. Instead,
have a Yamaha dealer check the vehicle.
2. Check the spark plug for electrode
erosion and excessive carbon or
other deposits, and replace it if necessary.
Specified spark plug:
CR7E (NGK)
To install the spark plug
1. Measure the spark plug gap with a
wire thickness gauge and, if necessary, adjust the gap to specification.
EAUT1180
Spark plug gap:
0.7~0.8 mm (0.028~0.031 in)
Engine oil and oil strainer
2. Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the
spark plug threads.
3. Install the spark plug with the spark
plug wrench, and then tighten it to
the specified torque.
Tightening torque:
Spark plug:
13 Nm (1.3 m•kgf, 9.4 ft•lbf)
NOTE:
If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4<->1/2 turn
past finger tight. However, the spark plug
should be tightened to the specified
torque as soon as possible.
4. Install the spark plug cap.
5. Install the panel.
The engine oil level should be checked
before each ride. In addition, the oil must
be changed and the oil strainer cleaned
at the intervals specified in the periodic
maintenance and lubrication chart.
To check the engine oil level
1. Place the vehicle on the center
stand.
NOTE
Make sure that the vehicle is positioned
straight up when checking the oil level.
A slight tilt to the side can result in a
false reading.
2. Start the engine, warm it up for several minutes, and then turn it off.
3. Wait a few minutes until the oil
settles, and then check the oil level
through the check window located
at the bottom-left side of the crankcase.
NOTE:
The engine oil should be between the
minimum and maximum level marks.
6-9
5YR-F8199-14_ch6.pmd
9
2007/05/24, 19:58
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
5. Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.
1
2
1
3
2
4
1
3
3 2
1
ZAUM00**
ZAUM00**
4
5
6
7
8
9
1. Engine oil filler cap
1
1. Engine oil level check window
2. Maximum level mark
3. Minimum level mark
ZAUM00**
1.
2.
3.
4.
4. If the engine oil is below the minimum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
To change the engine oil and clean
the oil strainer
1. Start the engine, warm it up for several minutes, and then turn it off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove panel A. (See page 6-8.)
4. Remove the engine oil filler cap and
drain bolts to drain the oil from the
crankcase.
1
ZAUM00**
1. Engine oil drain bolt A
ECA10410
cC
Engine oil drain bolt B
O-ring
Compression spring
Strainer
6. Check the O-ring for damage and
replace it if necessary.
7. Install the oil strainer, spring, O-ring
and engine oil drain bolts, and then
tighten the drain bolts to the specified torque.
When removing the engine oil drain
bolt, the O-ring, spring, and oil
strainer will fall out. Take care not to
lose these parts.
6-10
5YR-F8199-14_ch6.pmd
10
2007/05/24, 19:58
Final transmission oil<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
Tightening torque:
Engine oil drain bolt A:
23 Nm (2.3 m•kgf, 16.6 ft•lbf)
Engine oil drain bolt B:
32 Nm (3.2 m•kgf, 23.1 ft•lbf)
NOTE:
Make sure that the O-ring is properly
seated.
8. Add the specified amount of the
recommended engine oil, and then
install and tighten the engine oil filler
cap.
8 Be sure no foreign material enters the crankcase.
9. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off and
check for the cause.
10. Turn the engine off, and then check
the oil level and correct it if necessary.
11. Install the panel.
Recommended engine oil:
See page 8-1.
Oil change quantity:
1.00 L (1.06 US qt) (0.88 Imp.qt)
ECA11670
cC
EAU20061
Final transmission oil
The final transmission case must be
checked for oil leakage before each ride.
If any leakage is found, have a Yamaha
dealer check and repair the scooter. In
addition, the final transmission oil must
be changed as follows at the intervals
specified in the periodic maintenance
and lubrication chart.
1. Start the engine, warm up the final
transmission oil by riding the
scooter for several minutes, and
then stop the engine.
2. Place the scooter on the
centerstand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
4. Remove the oil filler cap and drain
bolt to drain the oil from the final
transmission case.
8 Do not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
11
2
3
4
5
6
7
8
9
6-11
5YR-F8199-14_ch6.pmd
1
2007/05/24, 19:58
Air filter and V-belt case air filter elements<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
1
1
EAUT1301
Tightening torque:
Final transmission oil drain bolt:
23 Nm (2.3 m•kgf, 16.6 ft•lbf)
Air filter and V-belt case air filter elements
6. Add the specified amount of the
recommended final transmission
oil, and then install and tighten the
oil filler cap.
2
3
ZAUM00**
4
1. Final transmission oil filler cap
5
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.13 L (0.14 US qt) (0.11 Imp.qt)
EWA11310
Cleaning the air filter element
1. Place the scooter on the
centerstand.
2. Remove the air filter case cover by
removing the screw.
w
1
6
The air filter and V-belt case air filter elements should be cleaned at the intervals specified in the periodic maintenance and lubrication chart. Clean both
filter elements more frequently if you are
riding in unusually wet or dusty areas.
8 Make sure that no foreign material enters the final transmission
case.
8 Make sure that no oil gets on the
tire or wheel.
7
8
1
ZAUM00**
9
1. Final transmission oil drain bolt
5. Install the final transmission oil
drain bolt, and then tighten it to the
specified torque.
7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
ZAUM00**
1. Air filter case cover
3. Pull the air filter element out, and
6-12
5YR-F8199-14_ch6.pmd
12
2007/05/24, 19:58
PERIODIC MAINTENANCE AND MINOR REPAIR
then blow the dirt out with compressed air as shown.
ECA10480
cC
8 Make sure that the air filter element is properly seated in the air
filter case.
8 The engine should never be operated without the air filter element installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.
1
6. Install the air filter case cover by
installing the screw.
ZAUM00**
1. Air filter element
ZAUM00**
4. Check the air filter element for damage and replace it if necessary.
5. Insert the air filter element into the
air filter case.
Cleaning the V-belt case air filter element
1. Remove the kickstarter lever by removing the bolt.
2. Remove the crankcase cover by removing the screws.
3. Remove the filter element holder by
removing the screw.
4. Pull the air filter element out, and
then clean it with solvent. After
cleaning, remove the remaining
solvent by squeezing the element.
EWA10430
w
Use only a dedicated parts cleaning
solvent. To avoid the risk of fire or
explosion, do not use gasoline or
solvents with a low flash point.
1
ECA10520
cC
To avoid damaging the air filter element, handle it gently and carefully,
and do not twist it.
5. Apply oil of the recommended type
to the entire surface of the sponge
material, and then squeeze the excess oil out.
NOTE:
The air filter element should be wet but
not dripping.
Recommended oil:
Engine oil
6. Insert the element into the air filter
case.
7. Install the filter element holder by
installing the screw.
8. Install the crankcase cover by installing the screws.
6-13
5YR-F8199-14_ch6.pmd
13
2007/05/24, 19:58
2
3
4
5
6
7
8
9
Carburetor<IXE>
Throttle cable free play, checking<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
9. Install the kickstarter lever by installing the bolt, then tightening the
bolt to the specified torque.
1
2
Tightening torque:
Kickstarter bolt:
23 Nm (2.3 m•kgf, 16.6ft•lbf)
3
EAU21251
Carburetor
The carburetor is an important part of
the engine and its emission control system, which requires very sophisticated
adjustment. Therefore, carburetor adjustments should be left to Yamaha dealer,
who has the necessary professional
knowledge and experience.
EAU21382
Checking the throttle cable
free play
The throttle cable free play should measure 3.0~5.0 mm (0.12~0.2 in) at the
throttle grip. Periodically check the
throttle cable free play and, if necessary,
have a Yamaha dealer adjust it.
4
5
6
7
8
9
6-14
5YR-F8199-14_ch6.pmd
14
2007/05/24, 19:58
Tires<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAUT1701
Tires
To maximize the performance, durability, and safe operation of your scooter,
note the following points regarding the
specified tires.
Tire air pressure
The tire air pressure should be checked
and, if necessary, adjusted before each
ride.
EWA10500
w
8 The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).
8 The tire air pressure must be
adjusted in accordance with the
riding speed and with the total
weight of rider, passenger, cargo,
and accessories approved for this
model.
Tire air pressure (measured on cold
tires):
Up to 90 kg (198 lb):
Front:
150 kPa (22 psi) (1.50 kgf/cm2)
Rear:
200 kPa (29 psi) (2.00 kgf/cm2)
90 kg (198 lb) to maximum load:
Front:
150 kPa (22 psi) (1.50 kgf/cm2)
Rear:
225 kPa (33 psi) (2.25 kgf/cm2)
Maximum load*:
144 kg (317 lb)
* Total weight of rider, passenger,
cargo and accessories
of your tires. NEVER OVERLOAD
YOUR VEHICLE. Make sure that the
total weight of the cargo, rider, passenger, and accessories (cowling,
saddlebags, etc. if approved for this
model) does not exceed the maximum load of the vehicle. Operation
of an overloaded motorcycle could
cause tire damage, an accident, or
even injury.
15
2
3
4
Tire inspection
5
1
6
EWA10510
w
Proper loading of your vehicle is important for several characteristics of
your vehicle, such as handling, braking, performance and safety. Do not
carry loosely packed items that can
shift. Securely pack your heaviest
items close to the center of the motorcycle, and distribute the weight
evenly from side to side. Properly
adjust the suspension for your load,
and check the condition and pressure
2
7
8
ZAUM0054
9
1. Tire tread depth
2. Tire sidewall
6-15
5YR-F8199-14_ch6.pmd
1
2007/05/24, 19:58
Wheels<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
The tires must be checked before each
ride. If a tire tread shows crosswise lines
(minimum tread depth), if the tire has a
nail or glass fragments in it, or if the
sidewall is cracked, have a Yamaha
dealer replace the tire immediately.
Minimum tire tread depth (front and
rear):
0.8 mm (0.03 in)
Cast wheels
EWA10580
NOTE:
The tire tread depth limits may differ from
country to country. Always comply with
the local regulations.
6
7
Tire information
This scooter is equipped with cast
wheels and tubeless tires with valves.
8
w
EWA10590
9
EAU21960
Front tire:
Size:
3.50-10 51J
Manufacturer/model:
CHENG SHIN C-922L
Rear tire:
Size:
3.50-10 51J
Manufacturer/model:
CHENG SHIN C-6007
Operating the scooter with excessively worn tires decrease riding stability and can lead to loss of control.
Have excessively worn tires replaced
by a Yamaha dealer immediately.
Brakes, tires, and related wheel parts
replacement should be left to a
Yamaha Service Technician.
w
8 It is dangerous to ride with a
worn-out tire. When a tire tread
begins to show crosswise lines,
have a Yamaha dealer replace the
tire immediately.
8 The replacement of all wheel- and
brake-related parts, including the
tires, should be left to a Yamaha
dealer, who has the necessary
professional knowledge and experience.
To maximize the performance, durability, and safe operation of your motorcycle, note the following points regarding the specified wheels.
8 The wheel rims should be checked
for cracks, bends or warpage before each ride. If any damage is
found, have a Yamaha dealer replace the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked wheel
must be replaced.
8 The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in poor
performance, adverse handling
characteristics, and a shortened
tire life.
8 Ride at moderate speeds after
changing a tire since the tire surface must first be “broken in” for it
to develop its optimal characteristics.
6-16
5YR-F8199-14_ch6.pmd
16
2007/05/24, 19:58
Front brake lever free play, checking<IXE>
Rear brake lever free play, adjusting<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAUT1220
EAU22170
Checking the front brake lever
free play
Adjusting the rear brake lever
free play
1
1
1
2
1
(b)
ZAUM00**
(a)
3
1. Adjusting nut
4
EWA10650
ZAUM0107
w
ZAUM0108
1. Front brake lever free play
1. Rear brake lever free play
The brake lever free play should measure 2.0~5.0 mm (0.08~0.20 in) as
shown. Periodically check the brake lever free play and, if necessary, have a
Yamaha dealer check the brake system.
The brake lever free play should measure 10.0~20.0 mm (0.39~0.79 in) as
shown. Periodically check the brake lever free play and, if necessary, adjust it
as follows.
To increase the brake lever free play,
turn the adjusting nut at the brake shoe
plate in direction (a). To decrease the
brake lever free play, turn the adjusting
nut in direction (b).
EWA10640
w
An incorrect brake lever free play indicates a hazardous condition in the
brake system. Do not operate the
motorcycle until the brake system has
been checked or repaired by a
Yamaha dealer.
If proper adjustment cannot be obtained as described, have a Yamaha
dealer make this adjustment.
6-17
5YR-F8199-14_ch6.pmd
17
2007/05/24, 19:58
5
6
7
8
9
Brake pads and shoes, checking<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU22380
Checking the front brake pads
and rear brake shoes
2
The front brake pads and the rear brake
shoes must be checked for wear at the
intervals specified in the periodic maintenance and lubrication chart.
3
Front brake pads
1
brake. If a brake pad has worn to the
point that the wear indicator almost
touches the brake disc, have a Yamaha
dealer replace the brake pads as a set.
limit line, have a Yamaha dealer replace
the brake shoes as a set.
EAU22540
Rear brake shoes
EAU22410
1
4
5
6
2
1
7
1. Wear indicator
2. Wear limit line
ZAUM00**
8
9
2
ZAUM00**
1. Brake pad wear indicator
2. Brake disc
Each front brake pad is provided with a
wear indicator, which allows you to
check the brake pad wear without having to disassemble the brake. To check
the brake pad wear, check the position
of the wear indicator while applying the
The rear brake is provided with a wear
indicator, which allows you to check the
brake shoe wear without having to disassemble the brake. To check the brake
shoe wear, check the position of the
wear indicator while applying the brake.
If a brake shoe has worn to the point
that the wear indicator reaches the wear
6-18
5YR-F8199-14_ch6.pmd
18
2007/05/24, 19:58
Brake fluid level, checking<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU32344
Checking the brake fluid level
1
LOWER
MIN
ZAUM00**
Observe these precautions:
8 When checking the fluid level, make
sure that the top of the master cylinder is level by turning the handlebars.
8 Use only the recommended quality
brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking performance.
brake fluid level goes down suddenly, have a Yamaha dealer check
the cause.
3
5
Insufficient brake fluid may allow air to
enter the brake system, possibly causing it to become ineffective.
Before riding, check that the brake fluid
is above the minimum level mark and
replenish if necessary. A low brake fluid
level may indicate worn brake pads and/
or brake system leakage. If the brake
fluid level is low, be sure to check the
brake pads for wear and the brake system for leakage.
8 Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and lead
to poor braking performance.
8 Be careful that water does not enter the master cylinder when refilling. Water will significantly lower the
boiling point of the fluid and may
result in vapor lock.
8 Brake fluid may deteriorate painted
surfaces or plastic parts. Always
clean up spilled fluid immediately.
8 As the brake pads wear, it is normal for the brake fluid level to
gradually go down. However, if the
6-19
5YR-F8199-14_ch6.pmd
2
4
Recommended brake fluid:
DOT 4
1. Minimum level mark
1
19
2007/05/24, 19:58
6
7
8
9
Brake fluid, changing<IXE>
Cables, checking and lubricating<IXE>
Throttle grip and cable, checking and lubricating<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU22720
Changing the brake fluid
1
2
3
4
Have a Yamaha dealer change the brake
fluid at the intervals specified in the
NOTE after the periodic maintenance
and lubrication chart. In addition, have
the oil seals of the brake master cylinder and caliper as well as the brake hose
replaced at the intervals listed below or
whenever they are damaged or leaking.
8 Oil seals: Replace every two years.
8 Brake hose: Replace every four
years.
5
EAU23091
EAU23111
Checking and lubricating the
cables
Checking and lubricating the
throttle grip and cable
The operation of all control cables and
the condition of the cables should be
checked before each ride, and the
cables and cable ends should be lubricated if necessary. If a cable is damaged or does not move smoothly, have
a Yamaha dealer check or replace it.
The operation of the throttle grip should
be checked before each ride. In addition, the cable should be lubricated at
the intervals specified in the periodic
maintenance chart.
Recommended lubricant:
Yamaha Chain and Cable Lube or
engine oil SAE 10W-30
EWA10710
w
6
Damage to the outer housing of
cables may result in internal rusting
and cause interference with cable
movement. Replace damaged cables
as soon as possible to prevent unsafe conditions.
7
8
9
6-20
5YR-F8199-14_ch6.pmd
20
2007/05/24, 19:58
Brake levers, lubricating<IXE>
Centerstand and sidestand, checking and lubricating<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU43640
EAU23211
Lubricating the front and rear
brake levers
Checking and lubricating the
centerstand and sidestand
Recommended lubricant:
Lithium-soap-based grease (allpurpose grease)
1
2
3
4
ZAUM00**
ZAUM00**
5
The pivoting points of the front and rear
brake levers must be lubricated at the
intervals specified in the periodic maintenance and lubrication chart.
Recommended lubricants:
Front brake lever:
Silicone grease
Rear brake lever:
Lithium-soap-based grease
(all-purpose grease)
The operation of the centerstand and
sidestand should be checked before
each ride, and the pivots and metal-tometal contact surfaces should be lubricated if necessary.
21
7
EWA10740
w
If the centerstand or sidestand does
not move up and down smoothly,
have a Yamaha dealer check or repair
it.
6-21
5YR-F8199-14_ch6.pmd
6
2007/05/24, 19:58
8
9
Front fork, checking<IXE>
Steering, checking<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23271
1
EAU23280
Checking the front fork
Checking the steering
The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic maintenance and lubrication chart.
Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as follows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Place a stand under the engine to
raise the front wheel off the ground.
2
To check the condition
EWA10750
3
w
4
Securely support the motorcycle so
that there is no danger of it falling
over.
ZAUM00**
5
6
7
8
9
Check the inner tubes for scratches,
damage and excessive oil leakage.
ECA10590
EWA10750
cC
w
If any damage is found or the front
fork does not operate smoothly, have
a Yamaha dealer check or repair it.
Securely support the motorcycle so
that there is no danger of it falling
over.
2. Hold the lower ends of the front fork
legs and try to move them forward
and backward. If any free play can
be felt, have a Yamaha dealer check
or repair the steering.
To check the operation
1. Place the motorcycle on a level surface and hold it in an upright position.
2. While applying the front brake, push
down hard on the handlebars several times to check if the front fork
compresses and rebounds
smoothly.
6-22
5YR-F8199-14_ch6.pmd
22
2007/05/24, 19:58
Wheel bearings, checking<IXE>
Battery<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23290
Checking the wheel bearings
EAUT1230
Battery
The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrication
chart. If there is play in the wheel hub or
if the wheel does not turn smoothly,
have a Yamaha dealer check the wheel
bearings.
ZAUM00**
1
2
3
1
4
ZAUM00**
1. Battery
5
This model is equipped with a sealedtype (MF) battery, which does not require any maintenance. There is no need
to check the electrolyte or to add distilled water.
6
7
ECA10620
cC
8
Never attempt to remove the battery
cell seals, as this would permanently
damage the battery.
9
EWA10760
w
8 Electrolyte is poisonous and dangerous since it contains sulfuric
6-23
5YR-F8199-14_ch6.pmd
23
2007/05/24, 19:58
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
acid, which causes severe burns.
Avoid any contact with skin, eyes
or clothing and always shield
your eyes when working near
batteries. In case of contact, administer the following FIRST AID.
9 EXTERNAL: Flush with
plenty of water.
9 INTERNAL: Drink large
quantities of water or milk
and immediately call a
physician.
9 EYES: Flush with water for
15 minutes and seek prompt
medical attention.
8 Batteries produce explosive hydrogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and provide sufficient ventilation when
charging it in an enclosed space.
8 KEEP THIS AND ALL BATTERIES
OUT OF THE REACH OF CHILDREN.
The battery is located under the
footboard. Remove panel B to access
the battery. (See page 6-7.)
To charge the battery
Have a Yamaha dealer charge the battery as soon as possible if it seems to
have discharged. Keep in mind that the
battery tends to discharge more quickly
if the vehicle is equipped with optional
electrical accessories.
To store the battery
1. If the vehicle will not be used for
more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.
2. If the battery will be stored for more
than two months, check it at least
once a month and fully charge it if
necessary.
3. Fully charge the battery before installation.
4. After installation, make sure that
the battery leads are properly connected to the battery terminals.
8 To charge a sealed-type (MF) battery, a special (constant-voltage)
battery charger is required. Using a conventional battery
charger will damage the battery.
If you do not have access to a
sealed-type (MF) battery charger,
have a Yamaha dealer charge
your battery.
ECA10630
cC
8 Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.
6-24
5YR-F8199-14_ch6.pmd
24
2007/05/24, 19:58
Fuse, replacing<IXE>
Headlight bulb, replacing<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAUT1240
Replacing the fuse
1
ECA10640
EAU23780
cC
Replacing the headlight bulb
Do not use a fuse of a higher amperage rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.
This model is equipped with a quartz
bulb headlight. If the headlight bulb burns
out, replace it as follows.
1. Remove the headlight unit by removing the screws.
1. Fuse
The fuse holder is located beside the
battery. Remove panel B to access the
fuse. (See page 6-8.)
If the fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
all electrical circuits.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
1
4
5
6
ZAUM00**
1. Headlight unit
2. Disconnect the headlight coupler,
and then remove the bulb cover.
6-25
25
7
8
9
Specified fuse:
10.0 A
5YR-F8199-14_ch6.pmd
2
3
3. Turn the key to “ON” and turn on
the electrical circuits to check if the
devices operate.
4. If the fuse immediately blows again,
have a Yamaha dealer check the
electrical system.
ZAUM00**
1
2007/05/24, 19:58
PERIODIC MAINTENANCE AND MINOR REPAIR
Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol
or thinner.
1
1
1
2
2
3
4
5
6
ZAUM00**
ZAUM00**
1. Headlight bulb holder
1. Headlight coupler
2. Bulb cover
EWA10790
5. Install the headlight bulb cover, and
then connect the coupler.
6. Install the headlight unit by installing the screws.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
w
3. Remove the headlight bulb holder
by turning it counterclockwise, and
then remove the defective bulb.
Headlight bulbs get very hot. Therefore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.
7
4. Place a new headlight bulb into position, and then secure it with the
bulb holder.
8
ECA10660
9
cC
Do not touch the glass part of the
headlight bulb to keep it free from oil,
otherwise the transparency of the
glass, the luminosity of the bulb, and
the bulb life will be adversely affected.
6-26
5YR-F8199-14_ch6.pmd
26
2007/05/24, 19:58
Tail/brake light bulb, replacing<IXE>
Turn signal light bulb, replacing<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU24131
Replacing the tail/brake light
bulb
wise the lens may break.
EAU24202
Replacing a turn signal light
bulb
1. Remove the turn signal light lens
by removing the screw.
1
1
2
2
2
3
1
4
ZAUM00**
5
1. Tail/brake light lens
2. Bulb
ZAUM00**
1. Turn signal light lens
2. Bulb
1. Remove the tail/brake light lens by
removing the screws.
2. Remove the defective bulb by pushing it in and turning it counterclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clockwise until it stops.
4. Install the lens by installing the
screws.
7
8
9
ECA10680
cC
Do not overtighten the screws, other6-27
5YR-F8199-14_ch6.pmd
27
6
2007/05/24, 19:58
Troubleshooting<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU25860
Troubleshooting
2
1
2
1
3
ZAUM00**
4
5
6
7
8
9
1. Turn signal light lens
2. Bulb
2. Remove the defective bulb by pushing it in and turning it counterclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clockwise until it stops.
4. Install the lens by installing the
screw.
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur during operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting chart represents a quick and easy procedure for
checking these vital systems yourself.
However, should your scooter require any
repair, take it to a Yamaha dealer, whose
skilled technicians have the necessary
tools, experience, and know-how to service the scooter properly.
Use only genuine Yamaha replacement
parts. Imitation parts may look like
Yamaha parts, but they are often inferior, have a shorter service life and can
lead to expensive repair bills.
ECA11190
cC
Do not overtighten the screw, otherwise the lens may break.
6-28
5YR-F8199-14_ch6.pmd
28
2007/05/24, 19:58
Troubleshooting chart<IXE>
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU25901
Troubleshooting chart
EWA10840
w
Keep away open flames and do not smoke while checking or working on the fuel system.
1
2
1. Fuel
3
There is enough fuel.
Check the compression.
There is no fuel.
Supply fuel.
Check the fuel level in
the fuel tank.
The engine does not start.
Check the compression.
4
5
2. Compression
There is compression.
Check the ignition.
There is no compression.
Have a Yamaha dealer
check the vehicle.
6
Operate the electric starter.
7
3. Ignition
Wet
Wipe off with a dry cloth and correct the
spark plug gaps, or replace the spark plugs.
Open the throttle halfway and operate
the electric starter.
8
Dry
Have a Yamaha dealer check the vehicle.
The engine does not start.
Check the battery.
9
Remove the spark plugs
and check the electrodes.
4. Battery
The engine turns over
quickly.
The battery is good.
The engine turns over
slowly.
Check the battery lead connections,
and charge the battery if necessary.
Operate the electric starter.
6-29
5YR-F8199-14_ch6.pmd
29
2007/05/24, 19:58
The engine does not start.
Have a Yamaha dealer
check the vehicle.
Care<IXE>
EAU25991
SCOOTER CARE AND STORAGE
EAU26091
axles. Always rinse the dirt and
degreaser off with water.
Care
1
2
3
4
5
6
7
8
9
While the open design of a scooter reveals the attractiveness of the technology, it also makes it more vulnerable.
Rust and corrosion can develop even if
high-quality components are used. A
rusty exhaust pipe may go unnoticed
on a car, however, it detracts from the
overall appearance of a scooter. Frequent and proper care does not only
comply with the terms of the warranty,
but it will also keep your scooter looking good, extend its life and optimize its
performance.
Before cleaning
1. Cover the muffler outlet with a plastic bag after the engine has cooled
down.
2. Make sure that all caps and covers as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such products onto seals, gaskets and wheel
●
Cleaning
ECA10781
cC
●
●
●
Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the affected area any longer than instructed. Also, thoroughly rinse
the area off with water, immediately dry it, and then apply a corrosion protection spray.
Improper cleaning can damage
plastic parts such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc. Use
only a soft, clean cloth or sponge
with mild detergent and water to
clean plastic.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
●
thinner, fuel (gasoline), rust removers or inhibitors, brake fluid,
antifreeze or electrolyte.
Do not use high-pressure washers or steam-jet cleaners since
they cause water seepage and
deterioration in the following
areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instruments, switches and lights),
breather hoses and vents.
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning compounds for plastic may leave
scratches on the windshield.
Test the product on a small hidden part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after washing.
7-1
5YR-F8199-14_ch7.pmd
1
2007/05/21, 17:41
SCOOTER CARE AND STORAGE
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge, and
then rinse thoroughly with clean water.
Use a toothbrush or bottlebrush for
hard-to-reach areas. Stubborn dirt and
insects will come off more easily if the
area is covered with a wet cloth for a
few minutes before cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely corrosive in combination with water, carry
out the following steps after each ride
in the rain, near the sea or on saltsprayed roads.
NOTE:
Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the engine has cooled down.
ECA10790
cC
Do not use warm water since it increases the corrosive action of the
salt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely before storing or covering it.
EWA10940
2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainlesssteel parts, including the exhaust
system. (Even the thermally induced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
3. To prevent corrosion, it is recommended to apply a corrosion protection spray on all metal, including chrome- and nickel-plated, surfaces.
4. Use spray oil as a universal cleaner
to remove any remaining dirt.
w
●
●
2
2
Make sure that there is no oil or
wax on the brakes or tires. If necessary, clean the brake discs
and brake linings with a regular
brake disc cleaner or acetone,
and wash the tires with warm
water and a mild detergent.
Before operating the scooter
test its braking performance and
cornering behavior.
ECA10800
3
4
5
6
7
cC
●
●
●
Apply spray oil and wax sparingly and make sure to wipe off
any excess.
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wear
7-2
5YR-F8199-14_ch7.pmd
1
2007/05/21, 17:41
8
9
Storage<IXE>
SCOOTER CARE AND STORAGE
EAU26300
away the paint.
1
Storage
NOTE:
Consult a Yamaha dealer for advice on
what products to use.
Short-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover.
ECA10820
2
cC
●
3
4
●
5
6
Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia) and
areas where strong chemicals
are stored.
7
Long-term
Before storing your scooter for several
months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Drain the carburetor float chamber
by loosening the drain bolt; this will
prevent fuel deposits from building
up. Pour the drained fuel into the
fuel tank.
8
9
3. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent the
fuel tank from rusting and the fuel
from deteriorating.
4. Perform the following steps to protect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap and
spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit sparking during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from
the spark plug, and then install
the spark plug and the spark plug
cap.
EWA10950
w
To prevent damage or injury from
sparking, make sure to ground the
7-3
5YR-F8199-14_ch7.pmd
3
2007/05/21, 17:41
SCOOTER CARE AND STORAGE
spark plug electrodes while turning
the engine over.
NOTE:
Make any necessary repairs before
storing the scooter.
5. Lubricate all control cables and the
pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
6. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alternatively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
7. Cover the muffler outlet with a plastic bag to prevent moisture from entering it.
8. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an excessively cold or warm place [less
than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the battery, see page 621.
1
2
3
4
5
6
7
8
9
7-4
5YR-F8199-14_ch7.pmd
4
2007/05/21, 17:41
Specifications<IXE>
EAU26320
SPECIFICATIONS
EAU2633K
Dimensions
1
2
3
4
Weight
6
Engine
7
8
9
Type
YAMALUBE 4, SAE10W30 or SAE20W40
Overall length
1755 mm (69.1 in)
Overall width
699 mm (27.5 in)
Overall height
1063 mm (41.9 in)
Seat height
759 mm (29.9 in)
Wheelbase
1230 mm (48.4 in)
Ground clearance
95 mm (3.74 in)
Minimum turning radius
1800 mm (70.9 in)
5
Engine oil
0
10
30
50
70
90
Type x quantity
BS26 x 1
Spark plug (s)
Manufacturer/model
NGK/CR7E
Spark plug gap
0.7-0.8 mm (0.028-0.031 in)
110 130 ˚F
YAMALUBE 4 (10W-30)
or SAE 10W-30
Clutch
YAMALUBE 4 (20W-40)
or SAE 20W-40
-20
-10
0
10
20
30
Clutch type
Dry, centrifugal automatic
Transmission
40 50 ˚C
Recommended engine oil grade
API service SG type or higher, JASO standard MA
Engine oil quantity
Periodic oil change
1.00 L (1.06 US qt) (0.88 Imp.qt)
With oil and fuel
109.0 kg (240 lb)
Final transmission oil
Engine type
Air cooled 4-stroke, SOHC
Cylinder arrangement
Forward-inclined single cylinder
Displacement
125.0 cm3
Bore x stroke
51.5 x 60.0 mm (2.03 x 2.36 in)
Compression ratio
9.80 :1
Starting system
Electric starter and kickstarter
Lubrication system
Wet sump
Type
SAE85W-140(GL5)
Quantity
0.13 L (0.14 US qt) (0.11 Imp.qt)
Air filter
Primary reduction system
Helical gear
Primary reduction ratio
40/15 (2.666)
Secondary reduction system
Spur gear
Secondary reduction ratio
38/13 (2.923)
Transmission type
V-belt automatic
Operation
Centrifugal automatic type
Chassis
Air filter element
Oil-coated paper element
Fuel
Recommended fuel
Unleaded gasoline only
Fuel tank capacity
4.7 L (1.24 US gal) (1.03 Imp.gal)
Carburetor
Frame type
Steel tube backbone
Caster angle
32.00 degree
Trail
75.0 mm (2.95 in)
Front tire
Type
Tubeless
Size
3.50-10 51J
Manufacturer
Mikuni
8-1
5YR-F8199-14_ch8.pmd
1
2007/05/24, 19:58
SPECIFICATIONS
Manufacturer/model
CHENG SHIN/C-922L
Front brake
Type
Single disc brake
Operation
Right hand operation
Recommended fluid
DOT 3 or 4
Rear tire
Type
Tubeless
Size
3.50-10 51J
Manufacturer/model
CHENG SHIN/C-6007
Rear brake
Type
Drum brake
Operation
Left hand operation
Loading
Maximum load
144 kg (317 lb)
Tire air pressure (measured on cold tires)
Loading condition
0-90 kg (0-198 lb)
Front
150 kPa (22 psi) (1.50 kgf/cm2)
Rear
200 kPa (29 psi) (2.00 kgf/cm2)
Loading condition
90 kg - maximum load
Front
150 kPa (22 psi) (1.50 kgf/cm2)
Rear
225 kPa (33 psi) (2.25 kgf/cm2)
Front wheel
Wheel type
Cast wheel
Rim size
J10 x MT2.5
(1.50 bar)
(2.00 bar)
Front suspension
Type
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
59.0 mm (2.32 in)
Rear suspension
(1.50 bar)
(2.25 bar)
Type
Unit swing
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
54.0 mm (2.13 in)
Electrical system
Voltage, capacity
12 V, 6.0 Ah
Headlight
Bulb type
Halogen bulb
Bulb voltage, wattage x quantity
Headlight
12 V, 60 W/55.0 W x 1
Tail/brake light
12 V, 8.0 W/27.0 W x 1
Front turn signal light
12 V, 10.0 W x 2
Rear turn signal light
12 V, 10.0 W x 2
License plate light
12 V, 8.0 W x 1
Meter lighting
14 V, 3.0 W x 1
Meter lighting (fuel meter)
14 V, 3.0 W x 1
High beam indicator light
14 V, 3.0 W x 1
Turn signal indicator light
12 V, 1.7 W x 1
Fuses
Main fuse
10.0 A
Wheel type
Cast wheel
Rim size
J10 x MT2.5
Battery
Model
GTX7A-BS / YTX7A-BS
8-2
5YR-F8199-14_ch8.pmd
2
2
3
4
5
6
7
8
9
Ignition system
CDI
Charging system
CDI magneto
Rear wheel
1
2007/05/24, 19:58
Identification numbers<IXE>
Key identification number<IXE>
Vehicle identification number<IXE>
EAU26342
CONSUMER INFORMATION
EAU26351
Identification numbers
1
2
3
4
Record the key identification number,
vehicle identification number and model
label information in the spaces provided
below for assistance when ordering
spare parts from a Yamaha dealer or
for reference in case the vehicle is stolen.
1
1
ZAUM00**
VEHICLE IDENTIFICATION NUMBER:
7
8
EAU26410
Vehicle identification number
KEY IDENTIFICATION NUMBER:
5
6
EAU26390
Key identification number
ZAUM00**
1. Key identification number
1. Vehicle identification number
The key identification number is
stamped into the key.
Record this number in the space provided and use it for reference when ordering a new key.
The vehicle identification number is
stamped into the frame.
NOTE:
The vehicle identification number is
used to identify your motorcycle and
may be used to register your motorcycle
with the licensing authority in your area.
MODEL LABEL INFORMATION:
9
9-1
5YR-F8199-14_ch9ind.pmd
1
2007/05/21, 17:42
Model label<IXE>
CONSUMER INFORMATION
EAU26460
Model label
1
1
2
3
4
ZAUM00**
1. Model label
5
The model label is affixed to the location shown. Record the information on
this label in the space provided. This
information will be needed when ordering spare parts from a Yamaha dealer.
6
7
8
9
9-2
5YR-F8199-14_ch9ind.pmd
2
2007/05/21, 17:42
Safety defects, reporting<IXE>
CONSUMER INFORMATION
EAU26551
Reporting safety defects
1
2
3
4
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation,
U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group
of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems
between you, your dealer, or Yamaha Motor Corporation, U.S.A.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http:/
/www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also obtain
other information about motor vehicle safety from http://www.safercar.gov.
5
6
7
8
9
9-3
5YR-F8199-14_ch9ind.pmd
3
2007/05/21, 17:42
Noise regulation<IXE>
CONSUMER INFORMATION
EAU26560
Motorcycle noise regulation
TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:
Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other
than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new
vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use
of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
1
“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.
3
These acts include tampering with the following systems; i.e., modification, removal, etc.
2
4
5
Exhaust system
Muffler
Exhaust pipe
Silencer
Intake system
Air cleaner case
Air cleaner element
Intake duct
6
7
8
9
9-4
5YR-F8199-14_ch9ind.pmd
4
2007/05/21, 17:42
Maintenance record<IXE>
CONSUMER INFORMATION
EAU26600
Maintenance record
1
2
3
Copies of work orders and/or receipts for parts purchased and installed on your motorcycle will be required to document
that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a
reminder that maintenance work is required. It is not acceptable proof of maintenance work.
Maintenance
interval
600 mi
(1000 km) or
1 month
4
2000 mi
(4000 km) or
6 months
5
4000 mi
(7000 km) or
12 months
6
6000 mi
(10000 km) or
18 months
7
8000 mi
(13000 km) or
24 months
8
10000 mi
(16000 km) or
30 months
9
12000 mi
(19000 km) or
36 months
Date of
service
Servicing dealer
name and address
Mileage
14000 mi
(22000 km) or
42 months
9-5
5YR-F8199-14_ch9ind.pmd
5
2007/05/21, 17:42
Remarks
CONSUMER INFORMATION
Maintenance
interval
16000 mi
(25000 km) or
48 months
Date of
service
Servicing dealer
name and address
Mileage
Remarks
1
18000 mi
(28000 km) or
54 months
2
20000 mi
(31000 km) or
60 months
3
4
5
6
7
8
9
9-6
5YR-F8199-14_ch9ind.pmd
6
2007/05/21, 17:42
Warranty, limited<IXE>
CONSUMER INFORMATION
EAU26681
YAMAHA MOTOR CORPORATION, U.S.A.
RIVA LIMITED WARRANTY
1
2
3
4
5
6
7
8
9
9-7
5YR-F8199-14_ch9ind.pmd
7
2007/05/21, 17:42
CONSUMER INFORMATION
1
2
3
4
5
6
7
8
9
9-8
5YR-F8199-14_ch9ind.pmd
8
2007/05/21, 17:42
Warranty, extended<IXE>
CONSUMER INFORMATION
EAU26750
YAMAHA EXTENDED SERVICE (Y.E.S.)
1
2
3
4
5
6
7
8
9
Keep your Yamaha protected even after your warranty
expires with genuine Yamaha Extended Service (Y.E.S.).
In addition, Travel and Recreation Interruption Protection
(TRIP) is included at no extra cost. TRIP gives you up to
$150 reimbursement per occurrence for any reasonable
expenses you incur because your Yamaha needs
covered service: replacement vehicle rental, emergency
towing, phone calls, even food and lodging when you are
away from home. This superb coverage goes into effect
when you purchase Y.E.S., so it applies to any warranty
repairs as well as covered repairs during your entire
Y.E.S. plan period.
Y.E.S. is designed and administered by Yamaha Motor
Corporation to provide maximum owner satisfaction. You
get uninterrupted factory-backed coverage for extra
peace of mind.
Y.E.S. is flexible. You choose the plan that’s right for
you: 12 months, 24 months, 36 months or, on certain
models, even 48 months beyond your warranty period.
Y.E.S. is designed and administered by the same
Yamaha people who handle your warranty – and it
shows in the comprehensive coverage benefits. There
are no mileage limitations. Coverage isn’t limited to
“moving parts” or the “drive train” like many other plans.
And Y.E.S. covers manufacturing defects just like the
warranty. See the sample contract at your Yamaha
dealer to see how comforting uninterrupted factorybacked protection can be.
You don’t have to pay anything for covered repairs.
There’s no deductible to pay, and repairs aren’t
“pro-rated.” You don’t have any “out-of-pocket” expenses
for covered repairs.
Y.E.S. coverage is honored at any authorized Yamaha
dealer nationwide.
Y.E.S. coverage is transferable to a new owner if you
sell or trade-in. That can make your Yamaha much more
valuable!
This excellent Y.E.S. plan coverage is only available to
Yamaha owners like you, and only while your Yamaha is still
within the Yamaha Limited Warranty period. So visit your
authorized Yamaha dealer to get all the facts. He can show
you how easy it is to protect your investment with Yamaha
Extended Service.
9-9
5YR-F8199-14_ch9ind.pmd
9
2007/05/21, 17:42
CONSUMER INFORMATION
We urge you to act now. You’ll get the excellent benefits of
TRIP coverage right away, and you’ll rest easy knowing
you’ll have strong factory-backed protection even after your
Yamaha Limited Warranty expires.
1
A special note:
If visiting your dealer isn’t convenient, contact Yamaha with
your Primary ID number (your frame number). We’ll be
happy to help you get the Y.E.S. coverage you need.
2
Yamaha Service Marketing
P.O. Box 6555
Cypress, CA 90630
1-(866)-YES-EXTD (1-866-937-3983)
3
4
5
6
7
8
9
9-10
5YR-F8199-14_ch9ind.pmd
10
2007/05/21, 17:42
INDEX
Fuse, replacing ...................................... 6-25
A
Acceleration and deceleration ................. 5-2
Air filter and V-belt case air filter
elements .............................................. 6-12
I
Identification numbers .............................. 9-1
Ignition circuit cut-off system ................. 3-10
Indicator lights .......................................... 3-2
K
Key identification number ......................... 9-1
Kickstarter ................................................ 3-6
C
Cables, checking and lubricating ........... 6-20
Carburetor .............................................. 6-14
Care .......................................................... 7-1
Carrier ...................................................... 3-9
Catalytic converter ................................... 3-6
Centerstand and sidestand, checking and lubricating ............................................... 6-21
D
Dimmer switch .......................................... 3-3
E
Engine break-in ........................................ 5-3
Engine oil and oil strainer ........................ 6-9
Engine stop switch ................................... 3-3
F
Final transmission oil ............................. 6-11
Front brake lever free play, checking ..... 6-17
Front fork, checking ............................... 6-22
Fuel .......................................................... 3-5
Fuel gauge ............................................... 3-2
Fuel tank cap ........................................... 3-4
5YR-F8199-14_ch9ind.pmd
11
Safe-riding points ..................................... 1-4
Safety defects, reporting .......................... 9-3
Safety information .................................... 1-1
Seat .......................................................... 3-7
Sidestand ............................................... 3-10
Spark plug, checking ............................... 6-8
Specifications ........................................... 8-1
Speedometer unit ..................................... 3-2
Start switch .............................................. 3-3
Starting a cold engine .............................. 5-1
Starting off ................................................ 5-2
Steering, checking ................................. 6-22
Storage ..................................................... 7-3
Storage compartment .............................. 3-8
Handlebar switches .................................. 3-3
Headlight bulb, replacing ....................... 6-25
Helmet holder ........................................... 3-7
High beam indicator light ......................... 3-2
Horn switch .............................................. 3-3
B
Battery .................................................... 6-23
Brake fluid level, checking ..................... 6-19
Brake fluid, changing ............................. 6-20
Brake lever, front ...................................... 3-4
Brake lever, rear ....................................... 3-4
Brake levers, lubricating ......................... 6-21
Brake pads and shoes, checking ........... 6-18
Braking ..................................................... 5-2
S
H
L
Labels, location of .................................... 1-6
Luggage hook .......................................... 3-9
M
Main switch/steering lock .........................
Maintenance and lubrication, periodic .....
Maintenance record .................................
Maintenance, emission control system ...
Maintenance, periodic ..............................
Model label ...............................................
3-1
6-4
9-5
6-3
6-1
9-2
N
Noise regulation ....................................... 9-4
P
Panels, removing and installing ...............
Parking .....................................................
Part locations ...........................................
Pre-operation check list ...........................
6-8
5-3
2-1
4-2
R
Rear brake lever free play, adjusting ..... 6-17
T
Tail/brake light bulb, replacing ................ 6-27
Throttle cable free play, checking .......... 6-14
Throttle grip and cable, checking and
lubricating ............................................ 6-20
Tires ....................................................... 6-15
Tool kit ...................................................... 6-1
Troubleshooting ........................................ 6-8
Troubleshooting chart ............................ 6-29
Turn signal indicator light ......................... 3-2
Turn signal light bulb, replacing ............. 6-27
Turn signal switch ..................................... 3-3
V
Vehicle identification number ................... 9-1
W
Warranty, extended .................................. 9-9
Warranty, limited ....................................... 9-7
Wheel bearings, checking ...................... 6-23
Wheels ................................................... 6-16
2007/05/21, 17:42
INDEX
5YR-F8199-14_ch9ind.pmd
12
2007/05/21, 17:42
1
2
3
4
5
6
7
8
9
5YR-F8199-14_ch9ind.pmd
13
2007/05/21, 17:42
1
2
3
4
5
6
7
8
9
5YR-F8199-14_ch9ind.pmd
14
2007/05/21, 17:42
1
2
3
4
5
6
7
8
9
5YR-F8199-14_ch9ind.pmd
15
2007/05/21, 17:42
1
2
3
4
5
6
7
8
9
5YR-F8199-14_ch9ind.pmd
16
2007/05/21, 17:42
YAMAHA MOTOR TAIWAN CO., LTD
PRINTED IN TAIWAN
×1!
2007.07-0.8×
(E)
5YR-F8199-14_ch0cv.pmd
1
2007/05/21, 17:38
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement