Craftsman | 973.274880 | Owner`s manual | Craftsman 973.274880 Owner`s manual

Owner's Manual
II:RRFTSMRN'I
Single Speed / Reversible
318in. PROFESSIONAL
CORDLESS DRILL-DRIVER
Model No.
973.274880
_, CAUTION:
Read and follow
all Safety Rules and Operating
Instructions before first use of
this product,
Sears;
Roebuck
972000-523
5-98
and Co.,
Hoffman
Estates,
IL 60179
USA
NRTL
•
Warranty .........................................................................................................................................................
2
•
Introduction and Product Specifications .........................................................................................................
2
•
Rules For Safe Operation ...........................................................................................................................
3-5
A. Important Safety Rules For Battery Tools ..............................................................................................
4
B. Important Safety Instructions For Charger .............................................................................................
C. Important Information For Recharging Hot Batteries .............................................................................
4
5
•
Accessodes ....................................................................................................................................................
6
•
Features .........................................................................................................................................................
6
•
Operation ...................................................................................................................................................
•
Maintenance .................................................................................................................................................
13
•
Battery Pack Removal and Preparation For Recycling ................................................................................
14
•
Exploded View and Repair Parts List ...........................................................................................................
15
•
Parts Ordedng / Service ...............................................................................................................................
16
FULL ONE YEAR WARRANTY
ON CRAFTSMAN
PROFESSIONAL
7-12
CORDLESS DRILL-DRIVER
If this CRRFTSMRN Professional Cordless Ddll-Ddver fails due to a defect in material or workmanship within one
year from the date of purchase, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE TOOL TO THE NEAREST SEARS
STORE IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
Your driU-ddver has many features for making drilling
operations more pleasant and enjoyable. Safety,
performance and dependability have been given top
pdodty in the design of this ddll-ddver making it easy
to maintain and operate.
_
CAUTION: Carefully read through this entire
owner's manual before using your new drill-driver.
Pay close attention to the Rules For Safe
Operation, Warnings and Cautions. If you use
your ddll-ddver properly and only for what it is
intended, you will enjoy years of safe, reliable
service.
SPECIFICATIONS:
Chuck Capacity
Motor
Charger Rating
No Load Speed
Switch
Charge Rate
Maximum Torque
3/8 in.
14.4 Volts DC
120 Volts, 60 Hz, AC Only
0-600 RPM
Variable Speed - Reversible
1 Hour
130 in. Ibs.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and
the explanations with them, deserve your careful attention and understanding. The safety warnings do
not by themselves eliminate any danger. The Instructions or warnings they give are not substitutes for
proper accident prevention measures.
SYMBOL
&
MEANING
SAFETY ALERT SYMBOL:
Indicateswamingor caution.May be used in conjunctionwith othersymbolsorpictographs.
A
A
NOTE:
_k
WARNING:
Failure to obey a safety waming can result in sarious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION:
Failure to obey a safety warning may result in property damage or personal injuryto
yourself or to others. Always follow the safety precautions to reduce the dsk of firs, electdc shock
and personal injury.
Advises you of information or instructions vital to the operation or maintenance of the equipment.
WARNING:
Do not attempt to operate this tool
until you have read thoroughly and understand
completely all instructions, safety rules, etc.
contained in this manual. Failure to comply can
result in accidents involving fire, electric shock,
or sedous personal injury. Save owner's
manual and review frequently for continuing
safe operation, and instructing others who may
use this tool.
•
attachment to do the job of a heavy duty tool.
Don't use tool for purpose not intended - for
example - A circular saw should never be used
for cutting tree limbs or logs.
M
KNOW YOUR POWER TOOL. Read owner's
manual carefully. Leam its applications and
limitations as well as the specifi(: potential
hazards related to this tool.
M
GUARD AGAINST ELECTRICAL SHOCK by
preventing body contact with grounded surfaces.
For example: Pipes, radiators, ranges, refrigerator enclosures.
•
KEEP WORK AREA CLEAN. Cluttered areas
and benches invite accidents.
•
AVOID DANGEROUS
ENVIRONMENT.
ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses;
they are NOT safety glasses.
PROTECT YOUR LUNGS. Wear a face mask or
dust mask if operation is dusty.
PROTECT YOUR HEARING. Wear headng
protection during extended periods of operation.
SECURE WORK. Use clamps or a vise to hold
work. It's safer than using your hand and it frees
both hands to operate tool.
Don't
DON'T OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
use power tool in damp or wet locations or
expose to rain. Keep work area well lit.
•
KEEP CHILDREN AND VISITORS AWAY. All
visitors should wear safety glasses and be kept a
safe distance from work area. Do not let visitors
contact tool or extension cord.
•
STORE IDLE TOOLS. When not in use tools
should be stored in a dry and high or locked-up
place - out of the reach of children.
•
DON'T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
WEAR PROPER APPAREL. Do not wear loose
clothing or jewelry that can get caught in tool's
moving parts and cause personal injury. Rubber
gloves and nonskid footwear are recommended
when working outdoors. Wear protective hair
covedng to contain long hair and keep it from
being drawn into nearby air vents.
READ ALL INSTRUCTIONS
m
USE RIGHT TOOL. Don't force small tool or
•
MAINTAIN TOOLS WITH CARE. Keep tools
sharp at all times, and clean for best and safest
performance. Follow instructions for lubdcating
and changing accessories.
REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from
tool before turning it on.
3
g
RULES
FOR SAFE OPERATION
(Continued)
NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could
ignite flammable liquids, gases, or fumes.
m
BA'R'ERIES NEAR FIRE OR HEAT. They may
explode.
DO NOT CHARGE BATTERY TOOL IN A
DAMP OR WET LOCATION.
KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products or any
strong solvents to clean your tool.
M
STAY ALERT. Watch what you are doing and
usa common sense. Do not operate tool when
you ere tired. Do not rush.
M
Your battery tool should be charged in a location
where the temperature is more than 50°F but
less than 100°F.
B
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets in your eyes, flush them
with clean water for at least 10 minutes, then
seek immediate medical attention.
B
If carrying your battery tool at your side, make
sure it is not running and your finger is not on the
switch. Avoid accidental starting.
CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that it
wi, operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced by an authorized service center unless
indicated elsewhere in this instruction manual.
SECURE WORK before applying power. NEVER
hold workpiece in your hand or across your legs.
M
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
IMPORTANT
CHARGER
DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, or any medication.
SAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
FOR
This manual
contains important safety and operating
instructions for battery charger part number
977405-000.
DRILLING OR DRIVING SCREWS INTO
ELECTRICAL WIRING IN WALLS, CEILINGS,
OR OTHER AREAS CAN CAUSE THE BIT OR
CHUCK TO BECOME ELECTRICALLY LIVE.
Do not touch metal parts when drilling into a wall;
grasp only the insulated handle(s) or plastic
housing when using this tool. Make sure hidden
electrical wiring, water pipes, and mechanical
hazards are not in the path of the bit when
drilling into a wall.
•
DO NOT PLACE BA'R'ERY TOOLS OR THEIR
Before using battery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger.
_
WARNING: To reduce risk of injury, charge only
nickel-cadmium type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
INSPECT FOR and remove all nails from lumber
Do not expose charger to rain or snow.
before drilling.
Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to
persons.
IMPORTANT SAFETY RULES FOR BATTERY
TOOLS
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible
hazards when not using your battery tool or
when changing accessories.
To reduce risk of damage to charger body and
cord, pull by charger body rather than cord when
disconnecting charger.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
USE ONLY THE CHARGER PROVIDED WITH
YOUR BATTERY TOOL. Do not substitute any
other charger. Use of another charger could
cause batteries to explode causing possible
serious injury.
4
RULES FOR SAFE OPERATION (Continued)
An extension cord should not be used unless
absolutely necessary. Use of improper
extension cord could result in a risk of fire and
electric shock. If extension cord must be used,
make sure:
a.
Do not operate charger if it has received a
sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualified
serviceman.
•
Do not disassemble charger;,take it to a
qualified serviceman when service or repair is
That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b.
That extension cord is propedy wired and in
good electrical condition; and
c.
That wire size is large enough for AC
ampere rating of charger as specified
below:
Cord Length (Feet) 25'
50'
100'
150'
Cord Size (AWG)
16
16
14
16
Note: AWG = Amedcan Wire Gage
DO NOT OPERATE CHARGER WITH A
DAMAGED CORD OR PLUG. If damaged,
have replaced immediately by a qualified
serviceman.
_i,
•
required, incorrect reassembly may result in a
risk of electric shock or fire.
•
To reduce risk of electric shock, unplug charger
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
•
Do not use charger outdoors.
•
Disconnect charger from power supply when
not in use.
•
SAVE THESE INSTRUCTIONS. Refer to them
frequently and use them to instruct others who
may use this tool. If you loan someone this tool,
loan them these instructions also.
Look for this symbol to point out important safety precautions. It means attention!H Your
safety is involved.
IMPORTANT
INFORMATION
FOR RECHARGING
HOT BATTERIES
When using your drill-driver continuollsly, the batteries in your battery pack will become hot. You should let a hot
battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack
becomes discharged and is hot, this will cause the yellow and green lights on your battery charger to come on
instead of the red light. The yellow and green lights indicate soft start mode and will switch to green only, indicating slow charge mode. The red light indicates fast charge mode, 1 hour charge time. The green light indicates
slow charge mode, requiring overnight charging for batteries to reach full charge. If the green light comes on
after letting battery pack cool down, remove it from charger for additional cooling. Once the battery pack cools
down, you can recharge battery pack in fast charge mode as normal. Do not leave a hot battery pack in charger
until it cools down. The green light will not go off when battery pack cools. If fast charge mode is desired, you
must physically remove a hot battery pack from the charger, let it cool, then place it back in charger after it has
cooled down.
Note: This situation only occurs when continuous use of your drill causes the batteries to become hot. It does
not occur under normal circumstances. Refer to "CHARGING YOUR DRILL-DRIVER" for normal recharging of
batteries. If the charger does not charge your battery pack under normal cimumstances, return both the battery
pack and charger to your nearest Sears repair center for electrical check.
,_
WARNING:
The operation of any power too! can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always wear
safety goggles or safety glasses with side shields and a full face shield when needed. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses
with side shields, available at Sears Retail Stores.
Thefollowingrecommended
accessodes
arecurrentlyavailableat
•
6-Pc. Extra Length Magnite Power Bit Set
•
30-Pc. Power ScrewddvedNutdriver Set and Case
•
17-Pc. Power Screwddver/Nutddver Set and. Case
•
High Speed Bits (For Wood or Metal)......3/4 inch Max.
•
Keyless Chuck (Item No, 20988)
WARNING:
Sears Retail Stores.
The use of attachments or accessories not listed might be hazardous.
KNOW YOUR DRILL-DRIVER
WRIST
See Figure 1.
See Figure 1.
Before attempting to use any tool familiarize yourself
with all operating features and safety requirements.
A wdst strap is provided to reduce the chances of
dropping your ddll-driver. Place one hand through the
wrist strap when carrying tool.
STRAP
BATTERYPACK
BRSTORAGE
LEVEL
KEYLESSCHUCK
YELLOWAND GREENLIGHTS
INDICATESOFT STARTMODE
GREENLIGHT "ON"
INDICATESSLOWCHARGING
MODEOR FULLYCHARGED
SWRCH
TRIGGER
WRISTSTRAP
BATTERY
CHARGER
_
_k
SCREWDRIVERBITS
Fig. 1
WARNING:
If any parts are missing, do not operate tool until the missing parts are replaced. Failure to do
so could result in possible serious personal injury.
6
_1
WARNING: Always wear safety goggles or
safety glasses with side shields when operating
tools. Failure to do so could result in objects
being thrown into your eyes, resulting in possible
serious injury.
•
WARNING:
Do not allow familiarity with your
drill-driver to make you careless. Remember that
a careless fraction of a second is sufficient to
inflict severe injury.
CHARGING YOUR DRILL-DRIVER
The battery pack for this tool has been shipped in a
low charge condition to prevent possible problems.
Therefore, you should charge it until light on front of
charger changes from red to green.
Note: Batteries will not roach full charge the first time
they are charged. Allow several cycles (drilling
followed by recharging) for them to become fully
charged.
III When your battery pack becomes fully charged, the
rod light will tum OFF and the green light will tum
ON.
o
•
Charge battery pack only with the charger
provided.
•
Make sure power supply Is normal house
voltage, 120 volts, 60 Hz, AC only;
•
Connect charger to power supply.
•
Place battery pack in charger aligning raised rib in
charger with groove in battery pack.
•
Press down on battery pack to be sure contacts on
battery pack engage properly with charger
contacts.
After normal usage, 1 hour of charging time is
required to be fully charged. A minimum charge
time of 1-112 hours is required to recharge a
completely discharged tool.
•
The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
•
Do not place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
_
CAUTION: Your drill-driver's battery pack
contains special high temperature batteries to
help prevent battery damage when left on charge
for extended periods of time. However, once the
batteries become fully charged, we recommend
that you unplug your charger from power supply
and remove the battery pack.
TO CHARGE
•
Normally, the yellow and green lights on charger
will come on. This indicates charger is in soft start
mode and should switch to fast charge mode within
5 minutes. When charger is in fast charge mode
the red light will come on. If after a period of 15
minutes the yellow and green lights remain on,
remove battery pack, wait I minute and reinsert
battery pack in charger. If the yellow and green
lights continue to remain on after an additional 15
minutes, the battery pack is damaged and will not
accept a charge. Return battery pack to your
nearest Sears Repair Center for checking or
replacing.
H
SWITCH
TO INSTALL
See Figure 2.
BATrERY
PACK
•
Lock switch trigger on your drill by placing the
direction of rotation selector in center position.
See Figure 2.
•
Place battery pack in your drill. Align raised rib
inside drill with groove on battery pack. See
Figure 3.
To turn your drill ON, depress the switch trigger. To
turn it OFF, release the switch trigger.
CENTERPOSITION
SELECTOR
TRIGGER
BAI"rERYPACK
1_
Fig. 2
SWITCH
LOCK
LATCHES
See Figure 2.
The switch trigger can be locked in the OFF position.
This feature can be used to prevent the possibility of
accidental starting when not in use. To lock switch
trigger, place the direction of rotation selector in
center position.
,_
WARNING:
Battery tools are always in
operating condition. Therefore, switch should
always be locked when not in use or carrying at
your side.
VARIABLE SPEED
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed
iscontrolled by the amount of switch trigger depression.
DEPRESSLATCHESTO
RELEASEBATrERY PACK
•
A
Note: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned, this is a
normal part of the switch function.
Fig. 3
Make sure the latches on each side of your
battery pack snap in place and battery pack is
secured in drill before beginning operation.
CAUTION: When placing battery pack in your
drill, be sure raised rib inside drill aligns with
groove on battery pack and latches snap in place
properly. Improper assembly of battery pack can
cause damage to internal components.
TO REMOVE
BA'I'FERY
PACK
•
Lock switch trigger on your drill by placing the
direction of rotation selector in center position.
See Figure 2.
•
Locate latches on end of battery pack and
depress to release battery pack from your drill.
See Figure 3.
•
Remove battery pack from your drill.
REVERSIBLE
KEYLESS CHUCK
See Figure 4.
SeeFigure_
This tool has the feature of being reversible. The
direction of rotation is controlled by a selector located
above the switch trigger. With the drill held in normal
operating position, the direction of rotation selector
should be positioned to the left of the switch for
drilling. The ddlling direction is reversed when the
selector is to the right of the switch. When the selector
is in center position, the switch trigger is locked.
Your new drill has a keylesschuck. As the name implies,
you can hand tighten or release drillbits in the chuck
jaws. Grasp and hold the collar of the chuck with one
hand. Rotate the chuck body with your other hand. The
arrows on the chuck indicate which directionto rotate
the chuck body in order to LOCK (tighten) or UNLOCK
(release) the drillbit.
UNLOCK
CENTERPOSITION
(LOCK)
(ReLeASE)
FORWARD
REVERSE
CHUCK
BOD_
SELECTOR
TRIGGER
DRILLBIT
Fig. 4
CAUTION: To prevent gear damage, always
allow chuck to come to a complete stop before
changing the direction of rotation.
To stop, release switch trigger and allow the chuck to
come to a complete stop.
CHARGER
A
See Figure 5.
Your charger has a "key hole" hanging feature for
convenient, space saving storage. Screws should be
installed so that center distances are 1-7/16 inches
aped.
BACKSIDE
OFCHARGER
I-7/16 in.
Fig. 5
9
LOCK
(TIGHTEN)
O
CHUCKCOLLAR
Fig. 6
WARNING:
Do not hold chuck body with one
hand and use power of the drill to tighten chuck
jaws on drill bits. Chuck body could slip in your
hand or your hand could slip and come in contact
with rotating drill bit. This could cause an
accident resulting in serious personal injury.
INSTALLING
BITS
REMOVING
See Figure 7.
BITS
See Figure 7.
Lock the switch tdgger by placing the direction of
rotation selector in canter position. See Figure 2.
Lock the switch trigger by placing the direction of
rotation selector in canter position. See Figure 2.
Open or close chuck jaws to a point where the
opening is slightly larger than the bit size you
intend to use. Also, raise the front of your drill
slightly to keep the bit from falling out of the chuck
Loosen the chuck jaws from drill bit.
To loosen: grasp and hold the collar of the chuck
with one hand, while rotating chuck body with your
other hand. Note: Rotate chuck body in the
direction of the arrow marked UNLOCK to loosen
chuck jaws.
jaws,
•
Insert drill bit into chuck the full length of the jaws
as shown in figure
t gure 7.
•
Tighten the chuck
c luck jaws on drill bit.
)it.
Do not use a wrench to tighten or loosen the
chuck jaws.
DRILLBIT
Remove drill bit from chuck jaws.
CHUCKBODY
•
I
ADJUSTABLE
TORQUE CLUTCH
Y(
Your
drill is equipped with an adjustable torque clutch
fo driving different types of screws into different matefor
dais.
riEo The proper setting depends on the type of matedal and the size of screw you are using,
•
Tl ADJUST
TO
TORQUE
Identify the twenty four torque indicator settings
located on the front of your drill. See Figure 9.
Rotate adjusting ring to the desired setting.
CHUCKCOLLAR
RIGHT
•
•
_k
Fig. 7
To tighten the chuck jaws on drill bit; grasp and
hold the collar of the chuck with one hand, while
rotating the chuck body with your other hand.
Note: Rotate the chuck body in the direction of
the arrow marked LOCK to tighten chuck jaws.
Do not use a wrench to tighten or loosen the
chuck jaws.
•
1-4
For driving small screws.
•
5-8
For ddving screws into soft
material,
•
9 - 12
• 13 - 16
For driving screws into soft and hard
materials.
For driving screws in hard wood.
• 17 - 20
For driving large screws.
• 21 - 24
For heavy drilling.
ADJUSTING
RING
TO DECREASE
TORQUE
WARNING:
Do not insert drill bit into chuck
jaws and tighten as shown in figure 8. This could
cause drill bit to be thrown from drill resulting in
possible serious personal injury or damage to the
chuck.
TO INCREASE
TORQUE
Fig. 9
Fig. 8
t0
BIT STORAGE
DRILLING
See Figure 10.
See Figure 12.
When not in use, bits provided with your drill can be
placed in the storage area located on the top of your
drill as shown in figure 10.
,_
WARNING: Always wear safety goggles or
safety glasses with side shields when operating
tools. Failure to do so could result in objects
being thrown into your eyes, resulting in possible
serious injury.
SCREWDRIVER
BITS
BITSTORAGEAREA
Fig. 10
Fig. 12
LEVEL DRILLING
When drilling hard smooth surfaces use a center punch
to mark desired hole location. This will prevent the drill
bit from slipping off center as the hole is started. However, the low speed feature allows starting holes without
center punching if desired. To accomplish this, simply
operate your drill at a low speed until the hole is started.
The material to be drilled should be secured in a vise or
See Figure 11.
A convenient feature provided with your drill is a level.
It is recessed in the motor housing on top of your drill.
It can be used to keep drill bits level during drilling
operations.
with clamps to keep it from turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece applying only
enough pressure to keep the bit cutting. Do not force or
apply side pressure to elongate a hole.
_k
WARNING: Be prepared for binding or bit
breakthrough. When these situations occur, drill
has a tendency to grab and kick opposite to the
direction of rotation and could cause loss of
control when breaking through material. If not
prepared, this loss of control can result in
possible serious injury.
When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil will prolong the life of
the bit and increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
Fig. 11
11
CHUCK
REMOVAL
Insert allen wrench in chuck and tighten chuck
jaws securely. Tap sharply with a mallet in a
counterclockwise direction. This will loosen chuck
See Figures 13, 14, and 15.
The chuck must be removed in order to use some
accessories. Toremove:
•
Lock the switch trigger by placing the direction of
rotation selector in center position.
•
Insert a 5/16 inch or larger allen wrench (hex key
wrench) intothe chuck of your drilland tighten the
chuck jaws securely.
•
Tap the allen wrench sharply with a mallet in a
clockwise direction. See Figure 13. This will
loosen the screw in the chuck for easy removal.
on the spindle. It can now be unscrewed by hand.
See Figure 15.
MALLET
KEYLESS
CHUCK
CHUCK
JAWS
Fig. 15
TO RETIGHTEN
A LOOSE
CHUCK
The chuck may become loose on spindle and develop
a wobble. Also, the chuck screw may become loose
causing the chuck jaws to bind and prevent them from
closing. To tighten, follow these steps:
Fig. 13
Open chuck jaws and remove allen wrench.
Remove the chuck screw by turning it in a clockwise direction. See Figure 14. Note: The screw
has left hand threads.
Fig. 14
12
•
Lock the switch trigger by placing the direction of
rotation selector in center position.
•
Insert allen wrench into chuck and tighten chuck
jaws securely. Tap allen wrench sharply with a
mallet in a clockwise direction. This will tighten
chuck on the spindle.
•
Open the chuck jaws and remove allen wrench.
•
Tighten the chuck screw. Note: The chuck screw
has left hand threads.
Do not abuse power tools. Abusive practices can
damage tool as well as workpiece.
WARNING:
When servicing, use only identical
Craftsman replacement parts. Use of any other
part may create a hazard or cause product
damage.
Only the parts shown on parts list, page fifteen, are
intended to be repaired or replaced by the customer.
All other parts should be replaced by a qualified
service technician at an authodzed service facility.
Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from vadous
types of commercial solvents and may be damaged
by their use. Use clean cloths to remove dirt, dust, oil,
grease, etc.
,_
_k
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc. come in contact with plastic parts. They
contain chemicals that can damage, weaken or
destroy plastic.
WARNING:
Do not attempt to modify this tool or
create accessories not recommended for use
with this tool. Any such alteration or modification
is misuse and could result in a hazardous
condition leading to possible sedous personal
injury.
BA'I'FERIES
Your drill's battery pack is equipped with 12 nickelcadmium rechargeable batteries. Length of service
from each charging will depend on the type of work
you are doing.
Store and charge your battedes in a cool area.
Temperatures above normal room temperature
will shorten battery life.
Never store battedes in a discharged condition.
Recharge them immediately after they are
discharged.
The batteries in this tool have been designed to
provide maximum trouble free life. However, like all
battedes, they will eventually wear out. Do not
disassemble battery pack and attempt to replace the
batteries. Handling of these batteries, especially
when wearing rings and jewelry, could result in a
serious bum.
All batteries gradually lose their charge. The
higher the temperature the quicker they lose their
charge. If you store your tool for long pedods of
time without using it, recharge the battedes every
month or two. This practice will prolong battery
life.
To obtain the longest possible battery life, we suggest
the following:
OVERLOAD
Your drill has a built-in overload protector to protect
the motor during overloading or prolonged use. The
ovedoad protector automatically activates to break the
circuit. When this occurs, allow your ddll to cool a few
seconds before resuming operation.
13
To preserve natural resources, please
recycle or dispose of expired battery
pack properly.
BA'R'ERY
This product contains nickel-cadmium
battery. Must be disposed of properly.
Local, state, or federal laws may
prohibit disposal of nickel-cadmium
batteries in ordinary trash. Consult
your local waste authority for
information regarding available
recycling and/or disposal options.
,_i
PACK
PREPARATION
14
REMOVAL
AND
FOR RECYCLING
WARNING:
Upon removal, cover the battery
pack's terminals with heavy duty adhesive tape.
Do not attempt to destroy or disassemble battery
pack or remove any of its components. Nickelcadmium batteries must be recycled or disposed
of properly. Also, never touch both terminals with
metal objects and/or body parts as short circuit
may result. Keep away from children. Failure to
comply with these wamings could result in fire
and/or serious injury.
CRAFTSMAN
PROFESSIONAL
MODEL
3/8 Inch CORDLESS
NO. 973.274880
DRILL-DRIVER
J
The model number will be found on a plate attached tothe motor housing. Always mention the model
number in all correspondence regarding your 3/8 in. CORDLESS DRILL-DRIVER or when ordering
repair pads.
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
2
5
3
4
PARTS LIST
Part
Number
Description
1
616478-003
Screw (Special) .............................................
1
2
973015-001
Chuck (Item No. 9-20988) .............................
1
3
967216-004
Wrist Strap .....................................................
1
4
977406-000
Battery Pack ..................................................
1
5
977405-000
Battery Charger .............................................
1
6
974371-000
Carrying Case - Not Shown ...........................
1
972000-523
Owner's Manual
Key
No.
15
Quen.
Forthe repairor replacementpartsyouneed
delivereddirectlyto yourhome
Call7 am- 7 prn,7 daysa week
1-800-366-PART
(1-800-366-7278)
Forrepairservice
Call24 hours a day,7 daysa week
1-800-4-REPAIR
(1-800-473-7247)
Forthelocationof a
SearsPartsandRepairCenterinyourarea
Call24 hours a day,7 daysa week
1-800-488-1222
ImRmmm
mmmmm
The model numberof thistoolwill befoundona serial plate
agachedto the motorhousing.Whenrequestingserviceor
orderingparts, alwaysprovidethe followinginformation:
• ProductName
3/8 in. Professional
CordlessDrill-Driver
• ModelNumber
973.274880
• Part Name
• PartNumber
SEARS
ArnetYca's
RepairSpecialists
Download PDF

advertising