AGFA DC-630x User manual
DC-630
User manual
Downloaded from ManualsCamera.com Manuals
Thank you for purchasing this DC-630 digital camera. Please read these operating instructions
carefully in order to use the product correctly. Keep the instructions in a safe place after reading
so that you can refer to them later.
Disclaimer
We assume no responsibility over and above the provisions of the Product Liability Law for damages
suffered by the user or third parties as a result of inappropriate handling of the product or its
accessories, or by their operational failure and by their use. We reserve the right to make changes to
this product and its accessories without prior notice.
Warning! Never try to open the camera or to take it apart. This will invalidate all guarantee claims.
Using Your Batteries
For best performance and prolonged battery life, we recommend the use of AA lithium or
rechargeable
Ni-MH batteries.
Extending battery life
The following functions use up a great deal of battery power and should therefore only be
used occasionally:
•
•
•
Excessive use of flash
Editing images on the camera display
Using the camera display as a view finder
The battery life can be affected by soiling. Please clean the contacts with a clean and dry cloth
before putting the batteries in the camera.
Battery performance drops at temperatures below 5 °C (41 °F). If you use the camera at low
temperatures you should have replacement batteries to hand and ensure they do not get too cold.
Please note: you should not dispose of cold and seemingly flat batteries because these batteries
may work again at room temperature.
-1Downloaded from ManualsCamera.com Manuals
Disposal of Waste Equipment by Users in Private Households in the European Union
This symbol on the product or on its packaging indicates that this product must not be
disposed of with your other household waste. Instead, it is your responsibility to dispose of
your waste equipment by handing it over to a designated collection point for the recycling of
waste electrical and electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and ensure that it is
recycled in a manner that protects human health and the environment. For more information
about where you can drop off your waste equipment for recycling, please contact your local
city office, your household waste disposal service or the shop where you purchased the
product.
Declaration of Conformity
We herewith confirm the following designated product: DC-630 has been tested and found to comply
with the requirements set up in the council directive on the approximation of the low of members
states relating to the EMC Directive 89/336/EEC, amended by 92/31/EEC & 93/68/ EEC. For the
evaluation regarding to the electromagnet compatibility, the following standards were applied
EN 55022:1998+A1:2000+A2:2003, Class B
EN 61000-3-2 edition 2:2000
EN 61000-3-3:1995+A1:2001
EN 55024:1998+A1:2001+A2:2003
IEC 61000-4-2:1995+A1:1998+A2:2001
IEC 61000-4-3:2002+A1:2002
IEC 61000-4-4:1995+A1:2001+A2:2001
IEC 61000-4-5:1995+A1:2001
IEC 61000-4-6:2004
IEC 61000-4-8:1993+A1:2001
IEC 61000-4-11:1994+A1:2001
The device is marked with CE Logo
-2Downloaded from ManualsCamera.com Manuals
FCC Compliance and Advisory
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.) this device may not cause harmful interference, and 2.) this device must accept any interference
received, including interference that may cause unsatisfactory operation.
This equipment has been tested and found to comply with the limits for a Class B peripheral, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communication. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. When shielded interface cables have been provided
with the product or when specified additional components or accessories have elsewhere been
designated to be used with the installation of the product, they must be used in order to ensure
compliance with FCC regulations.
-3Downloaded from ManualsCamera.com Manuals
Safety Information
Before using the camera, please ensure that you read and understand the safety precautions
described
below. Always ensure that the camera is operated correctly.
Do not aim the camera directly into the sun or other intense light sources which could damage your
eyesight.
Do not try to open the case of the camera or attempt to modify this camera in any way. High-voltage
internal components create the risk of electric shock when exposed. Maintenance and repairs should
be carried out only by authorized service providers.
Do not fire the flash too close to the eyes of animals or people, especially for young children. Eye
damage may result. In particular, remain at least one meter away from infants when using flash.
Keep the camera away from water and other liquids. Do not use the camera with wet hands. Never
use the camera in the rain or snow. Moisture creates the danger of fire and electric shock.
Keep the camera and its accessories out of the reach of children and animals to prevent accidents or
damage to the camera.
If you notice smoke or a strange odor coming from the camera, turn the power off immediately.
Take the camera to the nearest authorized service center for repair. Never attempt to repair the
camera on your own.
Use only the recommended power accessories. Use of power sources not expressly recommended
for this equipment may lead to overheating, distortion of the equipment, fire, electrical shock or other
hazards.
-4Downloaded from ManualsCamera.com Manuals
Table of Contents
SAFETY INFORMATION............................................................................................................................................ 4
TABLE OF CONTENTS................................................................................................................................................. 5
GETTING STARTED.................................................................................................................................................. 8
STANDARD ACCESSORIES .......................................................................................................................................... 8
Attaching the Wrist Strap ............................................................................................................................. 9
Using the Soft Case ...................................................................................................................................... 9
NAMES OF PARTS ................................................................................................................................................... 10
INSERTING THE BATTERIES ....................................................................................................................................... 12
Low Battery Indicator .................................................................................................................................. 12
INSERTING A MEMORY CARD ..................................................................................................................................... 13
About Camera Memory ................................................................................................................................ 13
DCF Protocol ................................................................................................................................................ 13
SETTING THE DATE AND TIME ................................................................................................................................... 14
BASIC OPERATIONS .............................................................................................................................................. 15
TURNING THE POWER ON AND OFF ........................................................................................................................... 15
Power Saving Function ................................................................................................................................ 15
SWITCHING BETWEEN RECORD AND PLAYBACK ........................................................................................................... 16
In Record mode ............................................................................................................................................ 16
In Playback mode ......................................................................................................................................... 16
USING THE MENUS.................................................................................................................................................. 17
Recording Menu / Playback Menu............................................................................................................... 17
ADJ. Menu ..................................................................................................................................................... 17
Setup Menu .................................................................................................................................................. 17
USING THE LCD MONITOR ........................................................................................................................................ 18
LCD Screen Indicator ................................................................................................................................... 18
Switching the Screen Display ..................................................................................................................... 19
RECORDING ............................................................................................................................................................ 20
RECORDING STILL IMAGES ........................................................................................................................................ 20
Using the Zoom Function ............................................................................................................................ 21
Using the Flash ............................................................................................................................................ 22
Using the Self-timer & Burst....................................................................................................................... 23
Using the Macro mode ................................................................................................................................ 24
RECORDING MOVIE CLIPS ......................................................................................................................................... 25
VOICES RECORDING ................................................................................................................................................. 25
SETTING THE RECORDING FUNCTIONS ........................................................................................................................ 26
-5Downloaded from ManualsCamera.com Manuals
Using the Scene Mode ................................................................................................................................ 26
Setting the Resolution and Quality ............................................................................................................. 27
Setting the Movie Size ................................................................................................................................ 27
Setting the White Balance .......................................................................................................................... 28
Setting the ISO ............................................................................................................................................ 28
Setting the Exposure................................................................................................................................... 29
Setting the Metering.................................................................................................................................... 29
Setting the Sharpness ................................................................................................................................ 29
Setting the Photo Effect ............................................................................................................................. 30
Setting Date Stamp ..................................................................................................................................... 30
PLAYBACK.............................................................................................................................................................. 31
PLAYING BACK IMAGES ............................................................................................................................................ 31
Using the Thumbnail.................................................................................................................................... 31
Magnifying Still Images ................................................................................................................................ 31
Playing Back Movie Clips ............................................................................................................................. 32
PLAYING BACK SOUNDS .......................................................................................................................................... 33
Recording a Voice Memo ............................................................................................................................. 33
Playing Back a Voice Memo......................................................................................................................... 33
DELETING FILES...................................................................................................................................................... 34
Deleting a Single File ................................................................................................................................... 34
Deleting All Files .......................................................................................................................................... 34
Protecting Files ............................................................................................................................................ 35
EDITING IMAGES...................................................................................................................................................... 36
Rotating Still Images ................................................................................................................................... 36
Changing the Image Size ............................................................................................................................ 36
PLAYING A SLIDE SHOW .......................................................................................................................................... 38
COPYING THE FILES ................................................................................................................................................. 38
SETUP SETTINGS .................................................................................................................................................. 39
ADJUSTING SOUNDS ................................................................................................................................................ 39
SETTING AUTO REVIEW ........................................................................................................................................... 39
SETTING THE POWER SAVE ...................................................................................................................................... 39
SETTING THE LANGUAGE ......................................................................................................................................... 40
RESETTING THE FILE NUMBERS ................................................................................................................................ 40
About the Folder & File Name..................................................................................................................... 40
Folder Structure ........................................................................................................................................... 40
File Naming .................................................................................................................................................. 41
SETTING THE TV OUT ............................................................................................................................................. 41
SETTING USB PORT ............................................................................................................................................... 41
CHOOSING A STARTUP IMAGE ................................................................................................................................... 42
-6Downloaded from ManualsCamera.com Manuals
FORMATTING THE MEMORY....................................................................................................................................... 42
RESETTING TO DEFAULT SETTINGS ............................................................................................................................ 43
MAKING CONNECTIONS ........................................................................................................................................ 43
CONNECTING THE CAMERA TO A TV .......................................................................................................................... 43
CONNECTING THE CAMERA TO A PC .......................................................................................................................... 44
Using the Card Reader ................................................................................................................................ 44
Connecting the Camera to a Computer with a USB Cable ........................................................................ 44
SOFTWARE INSTALLATION .................................................................................................................................. 45
SYSTEM REQUIREMENTS .......................................................................................................................................... 45
INSTALLING THE SOFTWARE ..................................................................................................................................... 46
INSTALLING THE SOFTWARE DRIVER .......................................................................................................................... 47
INSTALLING ULEAD PHOTO EXPLORER 8 SE BASIC ..................................................................................................... 47
INSTALLING VIDEOSTUDIO 7 SE VCD ....................................................................................................................... 47
USING THE SOFTWARE ............................................................................................................................................ 48
APPENDIX............................................................................................................................................................... 49
TROUBLESHOOTING ................................................................................................................................................. 49
SPECIFICATIONS ...................................................................................................................................................... 50
-7Downloaded from ManualsCamera.com Manuals
Getting Started
Standard Accessories
Camera
USB cable
Video out cable
Soft case
Strap
2 x AA batteries
Software Installation
CD-ROM
User’s manual
-8Downloaded from ManualsCamera.com Manuals
Attaching the Wrist Strap
Attach the wrist strap to your camera as
shown.
NOTE:
Do not swing the camera when
carrying by the wrist strap.
Using the Soft Case
When not using the digital camera, keep it in
the soft case for protection.
-9Downloaded from ManualsCamera.com Manuals
Names of Parts
Top
Front
Bottom
- 10 Downloaded from ManualsCamera.com Manuals
Back
Side
5-function button
- 11 Downloaded from ManualsCamera.com Manuals
Inserting the Batteries
The camera is powered by two AA-size alkaline batteries or rechargeable Ni-MH (min. 1600
mAh / 1.2V) batteries.
1. Slide the battery cover open.
2. Insert two AA-size alkaline batteries with
the positive (+) and negative (-) poles
matching the directions indicated inside the
battery room.
3. Slide the battery cover closed.
Low Battery Indicator
A low battery indicator
appears on the
LCD screen when the batteries are nearly
exhausted. Batteries should be replaced
promptly when the low batteries indicator
appears.
CAUTION:
Risk of explosion if battery is replaced by an incorrect type dispose of used batteries
according to the instructions.
NOTE:
Do not use manganese batteries. Manganese batteries cannot supply sufficient power
to support camera operation.
Replace all batteries at the same time. Never mix old and new batteries.
Remove batteries from the camera if you do not plan on using it for more than two
weeks.
The camera body may feel warm after extended use. This is normal.
- 12 Downloaded from ManualsCamera.com Manuals
Inserting a Memory Card
You can use SD Card or MMC Card with this digital camera. The memory card slot is located
beneath the battery cover, adjacent to the battery compartment.
1. Be sure that the camera is turned off.
2. Slide the battery cover and open it.
3. Insert the card with the label facing up and
the arrow pointing in.
4. Close the battery cover.
To remove the memory card, gently press on the
edge of the card and release it. Pull the card
out and close the battery cover.
About Camera Memory
The digital camera is equipped with internal memory. If the memory card is not inserted in
the camera, all images and movie clips recorded by the camera will be stored in the internal
memory. If the memory card is inserted, images and movie clips are stored on the memory
card.
DCF Protocol
The DCF protocol defines the format for image file data as well as the directory structure for
the memory card. Images that are taken by a DCF camera can be viewed on DCF-compatible
cameras from other manufacturers.
- 13 Downloaded from ManualsCamera.com Manuals
Setting the Date and Time
When the camera is first turned on, the date and time setting will not be correct. So before
using, be sure to set date and time.
1. Press the MENU button, using
SETUP (
2. Press
press
or
to select
) and press the SET button.
or
to select DATE & TIME (
) then
or the SET button to launch the Date &
Time screen.
3. Press
or
to change the value of the
highlighted field.
Press
or
to highlight
another field.
4. After adjusting the settings, press the SET or the
MENU button to apply the setting.
NOTE:
If you hold down
or , you can change the value quickly.
For printing images with Date & Time,
If the batteries are removed for about two days, the Date & Time setting will be lost. In
this case, make these settings again.
- 14 Downloaded from ManualsCamera.com Manuals
Basic Operations
Turning the Power On and Off
1. Press the POWER button to turn on the
camera in the Record mode. Or you can
press the
button to turn on the camera
in the Playback mode.
2. Press the POWER button again to turn the
power off.
Hint:
You can turn on the camera without the
start-up and operating sound by
pressing and holding the POWER or the
button over 1.5 seconds.
Power Saving Function
If the camera is turned off by Power Save feature, press the POWER or the
turn it on again.
The Power Save feature does not work in the following situation:
Connecting the camera to a computer or printer with the USB cable.
Connecting the camera with the AC adapter (sold separate).
- 15 Downloaded from ManualsCamera.com Manuals
button to
Switching between Record and Playback
You can switch between the Record mode and the Playback mode in following ways:
In Record mode
Press the MODE button to cycle through the still
image shooting, voice recording, and movie
recording.
Press the
mode.
button to switch to the Playback
NOTE:
If you switch to Playback mode, the lens will
retract after approximately 10 seconds.
In Playback mode
Press the MODE or the
button switch to the
previous used Record mode.
- 16 Downloaded from ManualsCamera.com Manuals
Using the Menus
Recording Menu / Playback Menu
When a menu screen is displayed, the arrow button and the SET button are used to make
the desired settings.
1. Press the MENU button to display the menu.
The menu displays depends on whether you are in the Record mode or the Playback
mode.
2. Press
or
to select a menu item.
3. Press
or
to change the setting.
In playback menu, press
or
to select an option, and then press the SET
button to display a confirmation screen or apply the setting.
4. Press the MENU or the SET button to save the settings and close the menu.
In playback menu, press the MENU button to close the menu.
ADJ. Menu
You can quickly adjust the White Balance, ISO, Exposure in Record mode.
1. Press the SET button to display the menu.
When movie recording, only White Balance can be adjusted.
2. Press
or
to select a menu item.
3. Press
or
to select an option
4. Press the SET button to confirm the settings and close the menu.
Setup Menu
You can change the basic settings of the camera in Record mode and Playback mode.
1. Press the MENU button to display the menu.
The menu displays depends on whether you are in the Record mode or the Playback
mode.
2. Press
or
to select SETUP (
) and then press the SET button to display the Setup
menu.
3. Press
or
to select a menu item and then press
submenu.
4. Press
or
to select an option and press
5. Press the MENU button to close the menu.
- 17 Downloaded from ManualsCamera.com Manuals
or the SET button to launch the
or the SET button to apply the setting.
Using the LCD monitor
The LCD monitor is used to compose images while recording, adjust settings and replay
images.
LCD Screen Indicator
In Recording
1
Mode icon
11
Shutter speed
2
Flash
12
Aperture value
3
Macro
13
Metering
4
Self-timer / Burst
14
Exposure
5
Zoom indicator
15
ISO
6
Battery
16
White balance
7
Storage media
17
Sharpness
8
Focus area
18
Quality
9
Shake warning
19
Resolution
10
Shots remaining
- 18 Downloaded from ManualsCamera.com Manuals
In Playback
1
Mode icon
6
Storage media
2
Protect
7
Capture date & time
3
Voice memo
8
DPOF
4
File number / Total
9
Resolution
5
Battery
Switching the Screen Display
Press the DISP button changes the next display mode of the LCD monitor as shown below:
In Record mode
In Playback mode
(1) OSD on
(4) OSD on
(2) Guide line
(5) OSD off
(3) OSD off
Hint:
Use the “Guide line” mode to compose images easily before shooting images.
NOTE:
When the LCD display is not in “OSD on”, press Macro, Self-timer, Flash will change the
display mode to “OSD on” automatically.
- 19 Downloaded from ManualsCamera.com Manuals
Recording
Recording Still Images
1. Hold the camera with both hands and make sure the camera is stable.
2. Set the camera to the Record mode
3. Aim the focus area to the subject that you want to take and press the shutter release
button halfway.
The focus area on the LCD monitor will light green when the camera is in focus.
If the shutter speed is slow or the possibility that image may be blurred, the shake
warning icon
may appear on the LCD monitor. To avoid it, use a tripod to
stabilize the camera when recording images.
4. Fully press the shutter release button to take an image.
NOTE:
Make sure that your fingers or the wrist strap does not block the lens.
When the shutter release button is pressed halfway down, check the exposure value
that appears on the LCD monitor to make sure that it is appropriate for the lighting
conditions.
- 20 Downloaded from ManualsCamera.com Manuals
Using the Zoom Function
Your camera has a combination of optical and
digital zoom functions that allow you to zoom in
on far away subjects or zoom out for a wide
angle shot.
The optical zoom is achieved by mechanically
adjusting the lens of the camera. The digital
zoom enlarges or shrinks the image using a
software process.
Press [W] to zoom out for a wide-angle shot.
Press [T] to zoom in for a telephoto shot.
When the zoom lever is pressed, the zoom bar ap
pears on the LCD monitor.
When the optical zoom factor is at maximum, zooming stops temporarily. Press the [T] again,
the camera switches to the digital zoom automatically and zooming continues.
Digital zoom works by enlarging the center portion of an image through a software
interpolation process. The digital zoom is used to achieve magnification levels up to approx.
4 times.
NOTE:
Digital zoom is unavailable when recording movies.
- 21 Downloaded from ManualsCamera.com Manuals
Using the Flash
Press the flash button cycles your camera through the various flash modes. A symbol
appears On the LCD screen to indicate the flash mode. The flash cannot be used when
movie recording.
1. Set the camera to the Record mode
The flash function only used in still image
shooting.
2. Press the
Display
button to change the flash mode:
Option
Description
Auto flash
Flash fires automatically when shooting conditions require
extra lighting.
Red eye
reduction
Flash strobes to let the subject’s eyes adjust to the flash,
then fires again to take the actual image. The digital camera
will detect the subject brightness and use the flash only
when required.
Always on
Flash fires every time you take a photo, regardless of
lighting conditions.
Slow sync
Flash fires with a slow shutter speed.
Always off
The flash never fires even in dark situation.
3. Shoot the image.
NOTE:
The flash charging time may increase when the battery is low.
- 22 Downloaded from ManualsCamera.com Manuals
Using the Self-timer & Burst
Use the self-timer to set a delay from the time the shutter button is pressed to the time the
image is shot. Use the burst to record four continuous still images shooting.
1. Set the camera to the Record mode
This function only used in still image
shooting.
button to change the
2. Press the
settings:
Display
Option
-
Single shot
Description
Record a single image.
2-SEC
The shutter release will be delay for 2 seconds.
10-SEC
The shutter release will be delay for 10 seconds.
Double
Record two images in a shot after pressing the shutter
release button 10 and 12 seconds.
Burst
For capturing 4 images in succession.
3. Shoot the image.
Each option automatically switches to single shot in the following situation:
After each shot.
When the mode switched.
When the camera is turned off.
NOTE:
When using the self-timer function, be sure to use a tripod or place the digital camera on
a level, stable surface.
- 23 Downloaded from ManualsCamera.com Manuals
Using the Macro mode
Your camera is equipped with a macro function that allows you to focus on very close
subjects. In macro mode you can focus on subjects 5 cm from the lens when in the maximum
wide angle (zoomed out) setting and 25 cm in the maximum telephoto (zoomed in) setting.
1. Set the camera to the Record mode
You can use the macro mode in still image
shooting or movie recording.
2. Press the
button to enter the macro mode.
The macro mode icon (
monitor.
) appears on the LCD
3. To leave the macro mode, press the
again.
button
NOTE:
Distances referred to measure the distance between the camera lens surface and the
subject.
- 24 Downloaded from ManualsCamera.com Manuals
Recording Movie Clips
Your camera can record movie clips with audio.
1. Set the camera to the Record mode
The LCD monitor displays the available
recording time.
2. Press the shutter to start recording.
3. Press the shutter again to end recording.
The camera will stop recording automatically
when the memory capacity has been
reached.
NOTE:
The voices of the movie clips are recorded from the microphone of the camera. Be careful
to avoid touching the microphone while recording.
The White Balance is set and locked to the settings of the first frame.
Voices Recording
You can record voices using this camera.
1. Set the camera to the Record mode
The LCD monitor displays the available
recording time.
2. Press the shutter to start recording.
3. Press the shutter again to end recording.
The camera will stop recording automatically
when the memory capacity has been
reached.
NOTE:
The voices are recorded from the microphone of the camera. Be careful to avoid touching
the microphone while recording.
- 25 Downloaded from ManualsCamera.com Manuals
Setting the Recording Functions
Using the Scene Mode
You can select from various scene mode for specific shooting conditions.
1. Set the camera to the Record mode
The scene mode function only used in still
image shooting.
2. Press the
button to show the Scene
Mode screen.
3. Use the arrow button to select a desired scene
mode and press the SET button to confirm the
setting.
Display
Option
Description
Program
All settings can be changed in this mode.
Portrait
Blurring the background to focus on the subject.
Landscape
Used for the wide scenic views.
Night Scene
Shooting the subject while keeping the background night
scenery.
Kids
Take a still image to capture moving kids.
Beach &
Snow
Used for the beach or snow scenes.
Backlight
Shooting the image of backlight object by changing metering.
Sunset
Enhance the red hue for recording sunset images.
Close-up
Close-up shooting for small subject.
Text
Enhance the black & white contrast.
Sports
Fireworks
Fast shutter speed to capture fast moving subjects.
Slow shutter speed to take fireworks exploding.
- 26 Downloaded from ManualsCamera.com Manuals
Setting the Resolution and Quality
You can select lower image resolution and quality to decrease the image size to capture
more images. Choose a suitable setting according to the desired image quality and purpose.
Resolution
Option
Description
3264x2448 - Suitable for printing large size paper.
2816x2112 - Suitable for printing normal size paper.
2784x1856 - Printing in 3:2 ratio.
2304x1728 - Suitable for printing on A4 paper.
1600x1200 - Suitable for printing on A5 paper.
640x480 - Suitable for attaching to e-mails or using in
websites.
Quality
Option
Description
Stores the image with an extremely low compression.
Stores the image with a low compression.
Stores the image with normal compression.
Setting the Movie Size
Movie clips can be shot with different size.
Option
Description
640x480 - Suitable for viewing on TV.
320x240 - Suitable for viewing on PC.
160x128 - Suitable for attaching to e-mails or using in
websites.
- 27 Downloaded from ManualsCamera.com Manuals
Setting the White Balance
Adjust the white balance to match different light sources such as sunlight, incandescent
(tungsten) lighting or, fluorescent lighting.
Option
Description
Automatically corrects white balance. Ideal for general
photography.
Adjusts for bright sun conditions, or natural light
conditions.
Adjusts for cloudy days or twilight conditions
Adjusts for normal indoor lighting conditions. Corrects the
orange hue of household light bulbs. Ideal for indoor
photos under tungsten or halogen lighting without a
flash.
Adjusts for fluorescent lighting. Corrects the green hue of
fluorescent lighting. Ideal for indoor photos under
fluorescent lighting without a flash.
For more accurate adjustment or when the light source
cannot be specified.
NOTE:
oint the camera at a white piece of paper or similar object under the lighting conditions for
which you want to set the white balance, and then press the SET button.
Setting the ISO
With the initial settings, the ISO sensitivity is automatically set according to the brightness of
the subject.
Option
Auto
Description
Sets the ISO sensitivity automatically.
ISO 50
Sets the sensitivity to ISO 50 equivalent.
ISO 100
Sets the sensitivity to ISO 100 equivalent.
ISO 200
Sets the sensitivity to ISO 200 equivalent.
- 28 Downloaded from ManualsCamera.com Manuals
NOTE:
Higher ISO speeds increase the image noise. To take clean images, use as low an ISO
speed as possible.
Setting the Exposure
Set the exposure value manually to compensate for unusual lighting conditions such as
indirect indoor lighting, dark backgrounds, and strong backlighting.
Setting the Metering
There are 3 different light metering options available on your camera.
Option
Description
Light is measured from the entire shooting screen, but
gives more importance to the values near the center.
Selects an exposure based on readings from multiple
points in the subject area
Selects an exposure based on a single reading taken
from the center of your picture.
Setting the Sharpness
You can select whether you want the image to have sharp or soft outlines.
Option
Description
The edges of the image are emphasized. The edges will
become sharp, but noise may occur in the recording
image.
The edges of the image are sharp. This is suitable for
printing.
The edges of the image are softened. This is suitable for
editing images on PC.
- 29 Downloaded from ManualsCamera.com Manuals
Setting the Photo Effect
You can add special effects to your images in Record mode or in Playback mode.
Option
Description
Off
No effect is added to the image.
B&W
Convert image to black & white.
Sepia
Recorded image will be stored in a sepia tone.
Neg. Art
Opposite what they were in the original image.
Mosaic
Add mosaic tiles to the images.
NOTE:
The mosaic effect only can be set in playback mode.
Setting Date Stamp
The Date Stamp function can be used to add a date to your pictures as you take them.
Option
Off
Date
Date & Time
Description
Do not add the recorded date & time to printed images.
Only add the recorded date to printed images.
Add the recorded date & time to printed images.
- 30 Downloaded from ManualsCamera.com Manuals
Playback
Playing Back Images
1. Set the camera to the Playback mode
2. Press
to play back the previous
image; press
to play back the next
image.
Hint:
Holding down
or
in a high speed.
scrolls images
Using the Thumbnail
When in Playback mode, you can view all your stored images in thumbnail format.
1. Set the camera to the Playback mode
2. Press the zoom lever [W], a thumbnail screen is
displayed.
3. Use the arrow button to select the desired image, and
press [T] or the SET button to show the selected
image in full screen.
Magnifying Still Images
1. Set the camera to the Playback mode (see page 14).
2. Press
or
to select the image that you want to
magnify or trimming.
3. Press [T] to magnify the image, and the central portion
of the image is displayed. You can use the arrow
button to view different parts of the magnified image.
Press the MENU button to return to the normal
size.
4. Press the SET button to set the image trimming.
5. Press the SET button again to trim the selected image
and save it as a new one.
Press the MENU button to cancel it
NOTE:
Only still images can be magnified and trimmed.
- 31 Downloaded from ManualsCamera.com Manuals
Playing Back Movie Clips
1. Set the camera to the Playback mode
2. Press
or
to select the movie clip
that you want to playback.
3. Press the SET button to start the movie.
The movie clip will play on the LCD
monitor.
4. Press the MENU button to stop the movie,
or press the SET button to pause the
movie.
When movie clip paused, press the
SET button again to resume.
Hint:
During movie playing back, press
to fast forward or press
to rewind it.
Press the shutter to capture the still image from the movie clip while it had paused.
- 32 Downloaded from ManualsCamera.com Manuals
Playing Back Sounds
1.
2.
3.
4.
Set the camera to the Playback mode
Press
or
to select the audio clip that you want to playback.
Press the SET button to start playing the audio clip.
Press the MENU button to stop the audio clip, or press the SET button to pause it.
When audio clip paused, press the SET button again to resume.
Recording a Voice Memo
You can add a voice memo to the still images after you record it.
1. Set the camera to the Playback mode
2. Press
or
to select a still image that you want to
add a voice memo.
3. Press the MENU button, using
or
to select
VOICE MEMO (
) and press the SET button.
If the image already has the voice memo recorded, the
appears on the LCD
monitor. The new recording will replace the previous one.
4. Press the SET button to start recording for 30 seconds, or press the MENU button to
cancel it.
5. Press the SET button again to end recording.
NOTE:
The voice memo cannot be added to a movie clip or a protected image.
You cannot delete only the voice memo. When you delete the image, the attached voice
memo is also deleted.
Playing Back a Voice Memo
1. Set the camera to the Playback mode
or
to select the image that has the voice
2. Press
memo recorded.
The image with a voice memo recorded shows
on the LCD monitor.
3. Press the SET button to play to voice memo.
- 33 Downloaded from ManualsCamera.com Manuals
4. Press the MENU button to stop the voice memo, or
press the SET button to pause it.
When voice memo paused, press the SET button
again to resume.
Deleting Files
Deleting a Single File
Single image can be deleted using the Playback Menu or pressing the camera button (
1. Set the camera to the Playback mode
Press the MENU button, then press
select DELETE (
or
to
).
2. Press
or
to select SINGLE, and then press the
SET button.
3. Press
or
to select the image you want to delete.
4. Press the SET button to delete the image or press the MENU button to cancel.
5. Repeat step 4~5 to delete images.
Hint:
To quickly delete the current display image
1. Select the image you want to delete.
2. Press the
button to show a confirmation bar.
3. Press the SET button to delete the current display image.
Deleting All Files
You can use the Playback Menu to delete multiple files.
1. Set the camera to the playback mode
2. Press the MENU button, then press
or
to select DELETE (
).
3. Press
or
to select ALL, and then press the SET button.
4. Press the SET button to delete all images or press the MENU button to cancel.
NOTE:
The protect images cannot be deleted with the delete function.
- 34 Downloaded from ManualsCamera.com Manuals
).
Protecting Files
Files stored on your camera or on a memory card can be protected to prevent accidental
deletion.
1.
2.
3.
4.
5.
Set the camera to the Playback mode
Press the MENU button, then press
or
to
).
select PROTECT (
Press
or
to select SINGLE, and then press
the SET button.
Press
or
to select the file you want to
protect.
Press the SET button to protect the file or press
the MENU button to cancel.
When the file is locked, the
displays on the
LCD monitor.
Repeat step 4~5 to protect images.
Hint:
To unlock the file, press the SET button again in step 5. The
file is unlocked.
To lock / unlock all files at a time
1. Set the camera to the Playback mode
will disappear and the
2. Press the MENU button, then press
or
to select PROTECT (
).
3. Press
or
to select LOCK ALL (or UNLOCK ALL), and press the SET button.
A confirmation message appears.
4. Press the SET button to lock (or unlock) all files, or press the MENU button to cancel.
- 35 Downloaded from ManualsCamera.com Manuals
Editing Images
Rotating Still Images
The still images can be rotated by various degrees.
1.
2.
3.
Set the camera to the Playback mode
Press
or
to select the image you want to rotate.
Press the MENU button, then press
or
to select
ROTATE (
4.
5.
).
Press
or
to select an option, and then press the
SET button.
Press the SET button to confirm the change or press the
MENU button to cancel.
The rotated image will be saved as a new file name.
Changing the Image Size
The resolution of still images that had already been recorded can be changed.
1.
2.
3.
Set the camera to the Playback mode
Press
or
to select the image you want to resize.
Press the MENU button, then press
or
to select
RESIZE (
4.
).
Press
or
to select an option, and then press the
SET button.
The resized image will be saved as a new file name.
NOTE:
Only a large size image can be resize to a smaller one.
- 36 Downloaded from ManualsCamera.com Manuals
Setting the DPOF
The Digital Print Order Format (DPOF) setting allows you to select images on the memory
card for printing and specify the number of print copies in advance using the camera. This is
extremely convenient for sending the images to a photo developing service or for printing on
a direct print function compatible printer.
1.
2.
Set the camera to the Playback mode
Press the MENU button, using
or
select DPOF (
3.
4.
5.
6.
7.
8.
9.
to
) and press the SET button.
Press
or
to select SINGLE, then press
the SET button.
Press
or
to select the image you want to print out, and the SET button.
Press
or
to specify the number of copies.
The number of copies can be set from 0 to 30.
To cancel this image DPOF setting, set the number of copies to 0.
Press
and then press
or
to set or cancel the date stamp of current image.
Press the SET button to apply the setting or press the MENU button to cancel.
Repeat step 4~7 to set other images for printing.
After you finished all image settings, press the MENU button to apply it.
Hint:
To set the DPOF setting for all images in a time, select ALL in step 3 and press the SET
button.
To reset all DPOF settings to initial default, select RESET in step 3 and press the SET
button.
- 37 Downloaded from ManualsCamera.com Manuals
Playing a Slide Show
You can set the camera to display images in a slide show.
1.
2.
Set the camera to the Playback mode
Press the MENU button, using
or
) and press the SET button.
SHOW (
3.
4.
to select SLIDE
Use the arrow button to set the playback interval ( )
and repeat or not (
).
You can set the interval between 1~10 seconds.
Press the SET button to start the slideshow, or press the MENU button to cancel.
During the slideshow, press the SET button to pause the slideshow and press the
SET button again to resume.
NOTE:
The slideshow function is not available for the movie clips and voice recording.
Copying the Files
You may want to copy the data from the camera’s internal memory to the memory card for
convenience.
1.
2.
3.
Be sure you had inserted a memory card to your digital
camera.
Set the camera to the Playback mode
Press the MENU button, using
or
to select COPY
TO CARD (
4.
Press
5.
button.
Press
6.
7.
8.
or
) and press the SET button.
to select SINGLE, then press the SET
or
to select the image you want to copy to a card.
Press the SET button to start copy.
Repeat step 5~6 to copy other images.
Press the MENU button to complete the setting.
Hint:
To copy all images to a memory card in a time, select ALL in step 4 and press the SET
button.
- 38 Downloaded from ManualsCamera.com Manuals
Setup Settings
Adjusting Sounds
You can adjust the sound volume and set different sounds as the start-up sound.
1. Set the camera to the Setup Menu
or
2. Press
then press
to select SOUNDS (
) and
or the SET button to enter the
sounds screen.
3. Use the arrow button to adjust the volume and
select a desired start-up sound.
4. Press the SET or the MENU button to apply
the setting.
5. Press the MENU button to close the menu.
Setting Auto Review
When Auto Review is enabled, you can view an image for a few seconds after you have taken
it.
Option
Off
Description
The captured image will not automatically display after
shooing.
3 sec.
The captured image will display for 3 seconds after
shooting.
5 sec.
The captured image will display for 5 seconds after
shooting.
Setting the Power Save
For power consumption, you can set your camera to turn off automatically for a period of time.
Option
Description
1 min.
The power will turn off automatically after 1 minute.
3 min.
The power will turn off automatically after 3 minutes.
5 min.
The power will turn off automatically after 5 minutes.
- 39 Downloaded from ManualsCamera.com Manuals
Setting the Language
The camera can display menus and other information in a number of different languages.
1. Set the camera to the Setup Menu
2. Press
or
to select LANGUAGE (
) then
press
or the SET button to launch the submenu.
3. Press
or
to select a language and press
or
the SET button to apply the setting.
4. Press the MENU button to close the menu.
Resetting the File Numbers
Use this function if the camera experiences a “Folder cannot be created” error or if you want
to restart numbering, for example, after erasing all files.
Resetting the file number is useful for avoiding the file name duplication when images are
downloaded to a computer.
Option
Description
Series
Store the latest used file number no matter deleting files
or inserting a new memory card.
Reset
Reset file numbering each time the memory card is
changed.
About the Folder & File Name
The digital camera automatically creates a directory of folders in the internal memory or
memory card that it uses to organize still images, movie clips and other information.
Folder Structure
Folder name begins with a 3-digit number from 100 to
999 and followed by “DICAM”, each folder holds up to
9999 files. If new files are made, a new folder named
in sequence will be made automatically.
- 40 Downloaded from ManualsCamera.com Manuals
File Naming
File name begins with “DSCI” and are followed by a 4-digit number that increases in
sequence. File numbering starts from 0001 when a new folder is created.
If the highest folder number is 999 and highest file number exceeds 9999, the camera will
display the warning message “Folder cannot be created”. When it appears, try one of the
following ways:
Reset the file number and plug in a new memory card.
The folder number and file number are initialized and renumbered from 100 and 0001
respectively.
NOTE:
Do not change the folder and file names in the memory card using your computer. It may
be unable to playback the data using the digital camera.
Setting the TV Out
Your camera can be connected to a TV allowing you to preview images and movie clips on the
television screen. TV Out should be set to either NTSC or PAL depending on your region.
Option
NTSC
PAL
Description
America, Japan, Taiwan, Korea
All of Europe
Setting USB Port
You can set USB mode to connect the camera with a printer or computer.
Option
Computer
Printer
Description
To connect your camera to a PC.
To connect your camera to a printer.
- 41 Downloaded from ManualsCamera.com Manuals
Choosing a Startup Image
You can choose a recorded image as the start-up image.
1.
2.
3.
Set the camera to the Playback mode
Press
or
to select a desired image.
Press the MENU button, then press
or
select S.IMAGE (
4.
to
).
Press
5.
or
to select an option, and then
press the SET button.
Set the camera to the Setup Menu
6.
Press
or
to select S.IMAGE (
) then
press
7.
8.
or the SET button.
Press
or
to select a desired image and
press the SET or the MENU button to apply the
setting.
Press the MENU button to close the menu.
NOTE:
The start-up image will not be deleted even if the original image is deleted or memory
formatted.
Formatting the Memory
To erase all data stored in the memory card if you are using a card, or all data stored in the
internal memory if there is no card inserted.
1. Set the camera to the Setup Menu
2. Press
or
to select FORMAT (
) then press
or the SET button.
3. Press the SET button to start format, or press the MENU button to cancel it.
A “BUSY...PLEASE WAIT” message displays and the memory card is starting format.
A “COMPLETED” message displays when finish formatting.
NOTE:
All data will be deleted including protected ones. Be sure to download important files to
your computer before formatting.
- 42 Downloaded from ManualsCamera.com Manuals
Resetting to Default Settings
You can reset the entire menu and button operation settings to initial default.
1. Set the camera to the Setup Menu
2. Press
or
the submenu.
3. Press
or
to select RESET ALL (
) then press
or the SET button to launch
to select YES then press the SET button to reset all settings.
NOTE:
The following settings do not change with this procedure:
Date & Time setting
Language setting
TV out setting
Making Connections
Connecting the Camera to a TV
Images displayed on the camera’s monitor screen can also be displayed on a television.
1. Use the included audio/video cable to connect
the camera to the TV set.
2. Set the TV input signal to Video In. Refer to
the documentation included with your TV for
more information.
3. Everything that would normally appear on the
camera’s LCD screen, such as photo and video
clip playback, slide shows, and image or video
capture, appears on the TV.
NOTE:
The camera LCD screen turns off automatically during video output.
- 43 Downloaded from ManualsCamera.com Manuals
Connecting the Camera to a PC
There are two ways to download files from the camera’s internal memory or memory card to
a computer:
by inserting the memory card into a card reader
by connecting the camera to a computer using the included USB cable
Using the Card Reader
1. Eject the memory from the camera and insert
it in a card reader that is connected to a
computer.
2. Open My Computer or Windows Explorer and
double-click the removable drive icon that
represents the memory card.
3. Copy images from the card into a directory of
your choice on the computer’s hard disk.
NOTE:
If you are using a PC card reader with a notebook computer, first insert the memory card
into the PC card adapter (optional), and then insert the PC card adapter into the
computer’s PC card slot.
Connecting the Camera to a Computer with a USB Cable
1. Install the USB software driver included
with the bundled CD-ROM.
2. Connect the supplied USB cable to the
computer’s USB port.
3. Turn on the camera.
4. The LCD screen turns off when the
connection to the computer has been
successfully completed.
5. Open My Computer or Windows
Explorer. A “Removable Disk” appears
in the drive list.
6. Double-click the “Removable Disk” icon
to view its contents.
7. Files stored on camera are located in
the folder name “DCIM”.
- 44 Downloaded from ManualsCamera.com Manuals
NOTE:
You don’t have to turn off the computer or camera when making this connection.
Refer to your computer’s manual for information regarding the USB port location.
The camera will turn off automatically if the USB cable is disconnected.
Windows 98/98SE: If this is the first time the camera has been connected to the
computer, Windows detects the camera as an “Unknown device” and automatically
completes the required software installation.
Software Installation
System Requirements
Windows:
PC with processor better than MMX Pentium 233 MHz
Windows XP/2000/ME/98SE/98
Minimum 32 MB RAM
USB port
CD-ROM drive
800x600 pixels, 16-bit color display compatible monitor
Macintosh:
Power Mac G3 or later
Mac OS 9.0, 9.1, 9.2 and OS X
Minimum 64 MB RAM
USB port
CD-ROM drive
800x600 pixels, 16-bit color display compatible monitor
*Specifications are subject to change without prior notice.
- 45 Downloaded from ManualsCamera.com Manuals
Installing the Software
The bundled software CD has the drivers and software that come with camera. Insert the CD
into your CD-ROM drive. The autorun menu appears:
The following software is listed:
Install Ulead Photo Explorer 8 SE Basic
Installs software for organizing and keeping track of you media.
Install VideoStudio 7 SE VCD
Installs software for editing captured movies.
Utilities
Installs several useful utilities fit viewing different types of media, and installs
the Adobe Acrobat Reader, which enables you to read documents in PDF
format.
User Manual
Opens this user manual.
Drivers
Installs camera drivers for Windows 98/98SE/ME/2000/XP.
Browse CD
Opens Windows Explorer and enables you to view the contents of the driver
and software CD.
*Click the items in the autorun menu to install the software.
NOTE:
If the autorun menu does not appear automatically, open the CD-ROM in My Computer or
Windows Explorer and double-click the file named” autorun.exe” to start the program.
You can also click Run in the Windows Startup menu, enter D:\autorun.exe (where D is
your CD-ROM drive letter)in the text box, and click OK.
- 46 Downloaded from ManualsCamera.com Manuals
Installing the Software Driver
Windows 98 (Second Edition) requires the installation if the driver to use the camera as a
mass storage device.
1. Install the included software installation CD-Rom in you computer’s CD-ROM drive. The
autorun menu appears.
2. Click Drivers. You are prompted to choose a setup language. Choose a setup language
and click OK.
3. Follow the on-screen instructions to install the drivers.
Installing Ulead Photo Explorer 8 SE Basic
Ulead Photo Explorer 8 SE Basic is a Photo management application that is included on the
software installation CD-ROM. This software requires Windows 98 Second Edition,
Windows ME, Windows 2000, or Windows XP on your computer.
1. Install the included software installation CD-Rom in you computer’s CD-ROM drive.
autorun menu appears.
2. Click Installing Ulead Photo Explorer 8 SE Basic.
3. Select a language and follow the on-screen instructions to install the drivers.
The
NOTE:
To play MPEG-4 files, both the software from the CD and Windows Media Player are
required. Windows Media Player is located under Utilities in the autorun menu.
Installing VideoStudio 7 SE VCD
VideoStudio 7 SE VCD is a video editing application hat is included on the software
installation CD-ROM. This software requires Windows 98 Second Edition, Windows ME,
Windows 2000, or Windows XP on your computer.
1. Install the included software installation CD-Rom in you computer’s CD-ROM drive.
autorun menu appears.
2. Click Installing VideoStudio 7 SE VCD.
3. Select a language and follow the on-screen instructions to install the drivers.
- 47 Downloaded from ManualsCamera.com Manuals
The
Using the Software
Ulead Photo Explorer 8 SE Basic
Ulead Photo Explorer 8.0 SE Basic is a versatile tool for owners of digital cameras.
Webcams, DV camcorders, scanners, or anyone who strives to handle digital media
effectively, Photo Explorer provides an efficient way to transfer, browse, modify and
distribute digital media.
Ulead Photo Explorer 8.0 SE Basic enables you to acquire photos and video or sound
clips from various digital devices; make modifications; send digital media through
e-mail, print photos, create slideshow presentations, burn your images onto CD or
DVD.
To start the program, click Start > Programs > Ulead Photo Explorer 8.0 SE Basic >
Ulead Photo Explorer 8.0 SE Basic.
VideoStudio 7 SE VCD
Ulead VideoStudio enables you to quickly and easily produce home videos complete
with attractive titles, video filters, transitions, and sound. Ulead VideoStudio
features an intuitive step-based interface that helps you get started right away.
After finishing a project, share your videos through e-mail or on the Web, or bum
your own high-quality VCDs, SVCDs and DVDs.
To start the program, click Start > Programs >Ulead VideoStudio7 > Ulead
VideoStudio 7 SE VCD.
- 48 Downloaded from ManualsCamera.com Manuals
Appendix
Troubleshooting
Problem
Power does not turn on.
Cause
Solution
Battery is inserted in the
Reload battery in the correct
wrong direction.
direction.
Batteries are dead.
Replace or recharge batteries.
The battery compartment
Make sure the battery compartment
door is open.
door is securely closed.
The camera does not take
The flash is charging.
Wait for the flash to charge.
pictures.
Memory is full.
Insert a new memory card.
Memory card is not
The card may be detective, use a new
formatted correctly.
card.
Image is not recorded when
The Flash is charge.
Wait for the flash to charge.
the shutter button is
Memory is full.
Insert a new memory card.
The flash does not fire
Flash is set to OFF.
Set the flash to any mode except off.
Image is blurry or out of
The camera was moving
Hold the camera steady when
focus.
when the image was
shooting picture.
pressed.
captured.
The subject was beyond
Turn the Macro mode on it the subject
the range within which the
is within 5 cm (zoom out) or 25 cm
camera can focus.
(zoom in).
Do not use Macro mode when
shooting distant subjects.
Image is not displayed on the A memory card with
This camera cannot display non-DCIF
LCD monitor.
images.
non-DCIF images (recorded
with other camera) is
loaded.
Recorded images are not
The camera was turned
If the battery low indicator appears
saved in memory.
off/powered down before
on the LCD monitor, replace the
the image was stored in
battery immediately.
memory
Cannot transfer images to a
USB driver is not installed.
Install the USB driver before you
computer after connecting
connect the camera to a computer /
the USB cable.
turn the camera on.
- 49 Downloaded from ManualsCamera.com Manuals
Specifications
Sensor
6.0 megapixel CCD
Size : 1/2.5 inch
Lens
Focal length : f=5.95 ~17.14mm ,
3X optical zoom, 4X digital zoom
LCD monitor
2.4” TFT color LCD
Focus range
Normal: 80cm ~ Infinity
Macro: (W) 5cm ~ 1m / (T) 50cm ~1m
Aperture
F/2.8 ~ 4.8
Shutter
8 ~ 1/2000 sec.
File Format
Still Image: JPEG (EXIF 2.2 compatible) , DCF compatible, Support DPOF
Video: AVI , Audio: WAV
Resolution
Still Image: 3264x2448 (Interpolation) / 2816x2112 / 2784x1856(3:2) /
2304x1728 / 1600x1200 / 640x480
Video: 640x480 / 320x240 / 160x120
Scene Mode
Portrait / Landscape / Night Scene / Kids / Beach & Snow / Backlight /
Sunset / Close up / Text / Sports / Fireworks
Sensitivity
Auto / ISO 50 / ISO 100/ ISO 200
White Balance
Auto / Daylight / Cloudy / Tungsten / Fluorescent (H) / Fluorescent (L) /
Custom
Exposure Control
-2EV to +2EV in 1/3 step
Metering
Center-weighted / Multi / Spot
Burst
4 images at one shot (6M / 3:2 / 4M / 2M / VGA)
Self-timer
2 sec. / 10 sec. / Double
Flash
Auto / Red eye reduction / Always on / Slow sync / Always off
Photo Effect
Black & White / Sepia / Negative Art / Mosaic
Storage
16 MB internal memory / SD / MMC slot
TV system
NTSC / PAL
Power Supply
2x AA battery
AA rechargeable Ni-MH batter X2 (optional)
AC power adaptor (3.3V) (optional)
Ambient
temperature
Operating: 0° C to 40° C
Storage: -20 to 60° C
Microphone
Built-in
Speaker
Built-in
Dimension
89 x 60.5 x 28.1 ( Max. 32.7, lens ~ LCD ) mm
Weight
Camera Body w/o battery: Approx. 140 (g)
*These specifications are subject to change without notice.
- 50 Downloaded from ManualsCamera.com Manuals
Customer care
More information to the complete product range can be found under: www.plawa.com
Service & Repair Hotline (Europe):
00800 75292100
Service & Support Hotline (Germany):
0900 1000 042 (1.49 Euro/ min. Deutsche Telekom)
Online Service:
[email protected]
Manufactured by plawa-feinwerktechnik GmbH & Co. KG
plawa-feinwerktechnik GmbH & Co. KG
Bleichereistr. 18
73066 Uhingen
Germany
- 51 Downloaded from ManualsCamera.com Manuals
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement