Motorola MOTOTRBO XPR 6380 User guide

PROFESSIONAL DIGITAL TWO-WAY RADIO SYSTEM
MOTOTRBO™
XPR™ 6350/ XPR™ 6380
NON-DISPLAY PORTABLE
USER GUIDE
Declaration of Conformity
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party
Name: Motorola Solutions, Inc.
Address: 1301 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A.
Phone Number: 1-800-927-2744
Declaration of Conformity
This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below.
Hereby declares that the product:
Model Name: XPR 6350/XPR 6380
conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)
Class B Digital Device
As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
i
English
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
Declaration of Conformity
• Increase the separation between the equipment and receiver.
ii
English
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Contents
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . i
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Important Safety Information . . . . . . . . . . . . . . . . . vii
Product Safety and RF Exposure Compliance . . . vii
Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Computer Software Copyrights . . . . . . . . . . . . . . . viii
Handling Precautions . . . . . . . . . . . . . . . . . . . . . . . . ix
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . 1
What Your Dealer/System Administrator
Can Tell You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Preparing Your Radio for Use . . . . . . . . . . . . . . . . . 2
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . 2
Attaching the Battery . . . . . . . . . . . . . . . . . . . . . . . . 3
Attaching the Antenna . . . . . . . . . . . . . . . . . . . . . . . 3
Attaching the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . 4
Attaching the Universal Connector Cover (Dust Cover)
Identifying Radio Controls . . . . . . . . . . . . . . . . . . . . . 6
Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . 7
Assignable Radio Functions . . . . . . . . . . . . . . . . . 7
Assignable Settings or Utility Functions . . . . . . . . . 8
Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . 8
Switching Between Conventional Analog and Digital
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Switching Between Internal and External Speakers 10
Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Contents
This User Guide contains all the information you need to
use the MOTOTRBO XPR Series Digital Portable Radios.
4
Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . 5
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . 5
Identifying Status Indicators . . . . . . . . . . . . . . . . . .11
LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Audio Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Receiving and Making Calls . . . . . . . . . . . . . . . . . .13
Selecting a Site . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Selecting a Radio Channel, Subscriber ID,
or Group ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Receiving and Responding to a Radio Call . . . . . . .14
Receiving and Responding to a Group Call . . . . .15
iii
English
Contents
Receiving and Responding to a Private Call . . .
Receiving an All Call . . . . . . . . . . . . . . . . . . . . . .
Receiving and Responding to a Phone Call . . . .
Phone Call as Group/Private/All Call . . . . . . . .
Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . .
Making a Call with the Channel Selector Knob . .
Making a Group Call . . . . . . . . . . . . . . . . . . . .
Making a Private Call . . . . . . . . . . . . . . . . . . .
Making an All Call . . . . . . . . . . . . . . . . . . . . . .
Making a Call with the One Touch Access
Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making a Group or Private Call . . . . . . . . . . . .
Making a Phone Call . . . . . . . . . . . . . . . . . . . .
Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . .
Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitoring Features . . . . . . . . . . . . . . . . . . . . . . . .
Monitoring a Channel . . . . . . . . . . . . . . . . . . . . .
Permanent Monitor . . . . . . . . . . . . . . . . . . . . . . .
19
19
20
21
21
22
22
22
Advanced Features . . . . . . . . . . . . . . . . . . . . . . . . .
Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting and Stopping Scan . . . . . . . . . . . . . . . .
Responding to a Transmission During a Scan . .
Deleting a Nuisance Channel . . . . . . . . . . . . . . .
Restoring a Nuisance Channel . . . . . . . . . . . . . .
23
23
24
24
24
25
25
iv
English
15
16
17
17
17
17
17
18
19
Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . . 25
Escalating Alarm Tone Volume . . . . . . . . . . . . . . 25
Call Alert Operation . . . . . . . . . . . . . . . . . . . . . . . . 26
Receiving and Responding to a Call Alert . . . . . 26
Making a Call Alert with the One Touch Access Button
26
Emergency Operation . . . . . . . . . . . . . . . . . . . . . . 27
Sending an Emergency Alarm . . . . . . . . . . . . . . 27
Sending an Emergency Alarm with Call . . . . . . . 28
Sending an Emergency Alarm with Voice to
Follow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Reinitiating an Emergency Mode . . . . . . . . . . . . 29
Exiting an Emergency Mode . . . . . . . . . . . . . . . . 30
Text Messaging Features . . . . . . . . . . . . . . . . . . . 30
Sending a Quick Text Message . . . . . . . . . . . . . 30
Privacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Starting an Automatic Site Search . . . . . . . . . . . 32
Stopping an Automatic Site Search . . . . . . . . . . 33
Starting a Manual Site Search . . . . . . . . . . . . . . 33
Lone Worker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Password Lock Features . . . . . . . . . . . . . . . . . . . . 34
Accessing the Radio from Password . . . . . . . . . 34
Unlocking the Radio from Locked State . . . . . . . 34
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Contents
Setting the Squelch Level . . . . . . . . . . . . . . . . . . 35
Setting the Power Level . . . . . . . . . . . . . . . . . . . . 35
Turning the Option Board Feature(s) On or Off . . 35
Turning the Voice Operating Transmission (VOX)
Feature On or Off . . . . . . . . . . . . . . . . . . . . . . . . . 36
Turning Radio Tones/Alerts On or Off . . . . . . . . . 36
Checking the Battery Strength . . . . . . . . . . . . . . . 36
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Earbuds and Earpieces . . . . . . . . . . . . . . . . . . . . . . 39
Headsets and Headset Accessories . . . . . . . . . . . . 39
Remote Speaker Microphones . . . . . . . . . . . . . . . . 40
Surveillance Accessories . . . . . . . . . . . . . . . . . . . . 40
Miscellaneous Accessories . . . . . . . . . . . . . . . . . . . 41
Batteries and Chargers Warranty . . . . . . . . . . . . . . 42
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
v
English
Notes
Notes
vi
English
Software Version
Product Safety and RF Exposure Compliance
All the features described in the following sections are
supported by the radio's software version R01.08.00 or
later.
!
Caution
Before using this product, read the operating
instructions for safe usage contained in the
Product Safety and RF Exposure booklet
enclosed with your radio.
ATTENTION!
This radio is restricted to occupational use only to
satisfy FCC RF energy exposure requirements.
Before using this product, read the RF energy awareness
information and operating instructions in the Product
Safety and RF Exposure booklet enclosed with your radio
(Motorola Publication part number 6881095C98) to
ensure compliance with RF energy exposure limits.
Please check with your dealer or system administrator
for more details of all the features supported.
Important Safety Information
Important Safety Information
For a list of Motorola-approved antennas, batteries, and
other accessories, visit the following website:
http://www.motorolasolutions.com/governmentandenterprise
vii
English
Computer Software Copyrights
Computer Software Copyrights
The Motorola products described in this manual may
include copyrighted Motorola computer programs stored
in semiconductor memories or other media. Laws in the
United States and other countries preserve for Motorola
certain exclusive rights for copyrighted computer
programs including, but not limited to, the exclusive right
to copy or reproduce in any form the copyrighted
computer program. Accordingly, any copyrighted
Motorola computer programs contained in the Motorola
products described in this manual may not be copied,
reproduced, modified, reverse-engineered, or distributed
in any manner without the express written permission of
Motorola. Furthermore, the purchase of Motorola
products shall not be deemed to grant either directly or by
implication, estoppel, or otherwise, any license under the
copyrights, patents or patent applications of Motorola,
except for the normal non-exclusive license to use that
arises by operation of law in the sale of a product.
viii
English
The AMBE+2TM voice coding Technology embodied in
this product is protected by intellectual property rights
including patent rights, copyrights and trade secrets of
Digital Voice Systems, Inc.
This voice coding Technology is licensed solely for use
within this Communications Equipment. The user of this
Technology is explicitly prohibited from attempting to
decompile, reverse engineer, or disassemble the Object
Code, or in any other way convert the Object Code into a
human-readable form.
U.S. Pat. Nos. #5,870,405, #5,826,222, #5,754,974,
#5,701,390, #5,715,365, #5,649,050, #5,630,011,
#5,581,656, #5,517,511, #5,491,772, #5,247,579,
#5,226,084 and #5,195,166.
Handling Precautions
• If the radio has been submersed in water, shake the radio
well to remove any water that may be trapped inside the
speaker grille and microphone port. Trapped water could
cause decreased audio performance.
• If the radio’s battery contact area has been exposed to water,
clean and dry battery contacts on both the radio and the
battery before attaching the battery to the radio. The residual
water could short-circuit the radio.
• If the radio has been submersed in a corrosive substance
(e.g. saltwater), rinse the radio and battery in fresh water then
dry the radio and battery.
• To clean the exterior surfaces of the radio, use a diluted
solution of mild dishwashing detergent and fresh water (i.e.
one teaspoon of detergent to one gallon of water).
the battery contact. This vent allows for pressure equalization
in the radio. Doing so may create a leak path into the radio
and the radio’s submersibility may be lost.
• Never obstruct or cover the vent, even with a label.
• Ensure that no oily substances come in contact with the vent.
• The radio with antenna attached properly is designed to be
submersible to a maximum depth of 1 meter (3.28 feet) and a
maximum submersion time of 30 minutes. Exceeding either
maximum limit or use without antenna may result in damage
to the radio.
• When cleaning the radio, do not use a high pressure jet spray
on the radio as this will exceed the 1 meter depth pressure
and may cause water to leak into the radio.
!
Caution
Handling Precautions
The MOTOTRBO Series Digital Portable radio meets IP57
specifications, allowing the radio to withstand adverse field
conditions such as being submersed in water.
• Never poke the vent (hole) located on the radio chassis below
Do not disassemble the radio. This could
damage radio seals and result in leak paths into
the radio. Radio maintenance should only be
done in service depot that is equipped to test
and replace the seal on the radio.
ix
English
Notes
Notes
x
English
Getting Started
How to Use This Guide
This User Guide covers the basic operation of the MOTOTRBO
Non-Display Portables.
However, your dealer or system administrator may have
customized your radio for your specific needs. Check with your
dealer or system administrator for more information.
What Your Dealer/System Administrator
Can Tell You
You can consult your dealer or system administrator about the
following:
• Is your radio programmed with any preset conventional
Getting Started
Take a moment to review the following:
How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . page 1
What Your Dealer/System Administrator
Can Tell You. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1
Selected features are also available on the single-site trunking
mode, Capacity Plus. See Capacity Plus on page 10 for more
information.
channels?
• Which buttons have been programmed to access other
features?
• What optional accessories may suit your needs?
Throughout this publication, the icons below are used to
indicate features supported in either the conventional Analog
mode or conventional Digital mode:
Indicates a conventional Analog Mode-Only feature.
Indicates a conventional Digital Mode-Only feature.
For features that are available in both Analog and Digital
modes, no icon is shown.
1
English
Charging the Battery
Preparing Your Radio for Use
Preparing Your Radio for Use
Assemble your radio by following these steps:
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching the Antenna. . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching the Belt Clip. . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching the Universal Connector
Cover (Dust Cover) . . . . . . . . . . . . . . . . . . . . . . . . . .
Powering Up the Radio . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . .
2
English
page 2
page 3
page 3
page 4
page 4
page 5
page 5
Your radio is powered by a Nickel Metal-Hydride (NiMH) or
Lithium-Ion (Li-lon) battery. To avoid damage and comply with
warranty terms, charge the battery using a Motorola charger
exactly as described in the charger user guide.
Charge a new battery 14 to 16 hours before initial use for best
performance.
IMPORTANT: ALWAYS charge your IMPRES battery with an
IMPRES charger for optimized battery life and
valuable battery data. IMPRES batteries
charged exclusively with IMPRES chargers
receive a 6-month capacity warranty extension
over the standard Motorola Premium battery
warranty duration.
Attaching the Battery
Attaching the Antenna
With the radio turned off, set the
antenna in its receptacle and turn
clockwise.
To remove the antenna, turn the
antenna counterclockwise. Make sure
you turn off the radio and remove the
universal connector cover (dust cover)
first.
!
Caution
If antenna needs to be replaced, ensure that only
MOTOTRBO antennas are used. Neglecting this will
damage your radio. See Antennas on page 37 for a
list of available antennas.
Preparing Your Radio for Use
Align the battery with the rails on the back of the radio. Press
the battery firmly, and slide upward until the latch snaps into
place. Slide battery latch into lock position.
To remove the
battery, turn the
radio off. Move the
battery latch into
unlock position
and hold, and slide
the battery down
and off the rails.
3
Battery Latch
English
Attaching the Belt Clip
Preparing Your Radio for Use
Align the grooves on the clip
with those on the battery and
press downward until you
hear a click.
To remove the clip, press the
belt clip tab away from the
battery using a key. Then
slide the clip upward and
away from the radio.
4
English
Attaching the Universal Connector Cover
(Dust Cover)
The universal connector is located on the antenna side of the
radio. It is used to connect MOTOTRBO accessories to the
radio.
Universal
Connector
Cover
(Dust Cover)
Place the universal connector
cover loop over the attached
antenna. Slide it all the way
down to the base of the
antenna.
Insert the hooked end of the
cover into the slots above the
universal connector. Press
downward on the cover to
seat the lower tab properly
into the RF connector.
Turn the thumbscrew clockwise to secure the connector cover
to the radio.
To remove the universal connector cover, press down on the
cover and turn the thumbscrew counterclockwise. Lift the cover
up, slide the connector cover loop upwards, and remove it from
the attached antenna.
Replace the dust cover when the universal connector is not in
use.
Powering Up the Radio
To increase the volume, turn the On/Off/Volume Control Knob
clockwise.
A brief tone sounds,
indicating that the power up
test is successful.
NOTE: There is no power up
tone if the radio
tones/alerts function
is disabled (see
Turning Radio
Tones/Alerts On or
Off on page 36).
If your radio does not power up, check your battery. Make sure
that it is charged and properly attached. If your radio still does
not power up, contact your dealer.
To turn off the radio, rotate this knob counterclockwise until you
hear a click.
To decrease the volume, turn this knob counterclockwise.
Preparing Your Radio for Use
Rotate the On/Off/Volume
Control Knob clockwise until
you hear a click. The LED
blinks green.
Adjusting the Volume
NOTE: Your radio can be programmed to have a minimum
volume offset where the volume level cannot be turned
down fully. Check with your dealer or system
administrator for more information.
5
English
1
Identifying Radio Controls
Identifying Radio Controls
6
11
2
Take a moment to review the following:
Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6
Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . . . page 7
Push-To-Talk (PTT) Button . . . . . . . . . . . . . . . . . . . . . . page 8
Switching Between Conventional Analog and
Digital Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9
Switching Between Internal and External Speakers . . page 10
Capacity Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10
10
3
9
4
5
8
6
Radio Controls
7
1
Channel Selector Knob
2
On/Off/Volume Control Knob
3
LED Indicator
9
4
Side Button 1*
10 Speaker
5
Push-to-Talk (PTT) Button
11 Emergency Button*
6
Side Button 2*
12 Antenna
7
Side Button 3*
8
Microphone
English
12
Universal Connector for Accessories
* These buttons are programmable.
Programmable Buttons
• Short press – Pressing and releasing rapidly (0.05 seconds).
• Long press – Pressing and holding for the programmed
duration (between 1.00 second and 3.75 seconds).
• Hold down – Keeping the button pressed.
NOTE: The programmed duration of a button press is
applicable for all assignable radio/utility functions or
settings. See Emergency Operation on page 27 for
more information on the programmed duration of the
Emergency button.
Assignable Radio Functions
Audio Routing – Toggles audio routing between internal and
external speakers.
Emergency – Depending on the programming, initiates or
cancels an emergency alarm or call.
One Touch Access
– Directly initiates a predefined
Private, Phone or Group Call, a Call Alert or a Quick Text
message.
Option Board Feature – Toggles option board feature(s) on or
off for option board-enabled channels.
Permanent Monitor *– Monitors a selected channel for all radio
traffic until function is disabled.
Phone Exit
Privacy
– Ends a Phone Call.
– Toggles privacy on or off.
Repeater/Talkaround* – Toggles between using a repeater and
communicating directly with another radio.
Identifying Radio Controls
Your dealer can program the programmable buttons as
shortcuts to radio functions or preset channels/groups
depending on the duration of a button press:
Nuisance Channel Delete* – Temporarily removes an
unwanted channel, except for the Selected Channel, from the
scan list. The Selected Channel refers to the user’s selected
zone/channel combination from which scan is initiated.
Scan* – Toggles scan on or off.
Site Lock On/Off*
– Toggles the automatic site roam on or
off.
Manual Site Roam*
– Starts the manual site search.
Monitor – Monitors a selected channel for activity.
Telemetry Control
– Controls the Output Pin on a local or
remote radio.
* Not applicable in Capacity Plus
English
7
Transmit Interrupt Remote Dekey
– Stops an ongoing
Push-To-Talk (PTT) Button
interruptible call to free the channel.
Voice Operating Transmission (VOX) – Toggles VOX on or
off.
Zone – Allows selection from a list of zones.
Identifying Radio Controls
Battery Strength – Indicates battery strength via the LED
Indicator.
Assignable Settings or Utility Functions
All Tones/Alerts – Toggles all tones and alerts on or off.
Power Level – Toggles transmit power level between high and
low.
Squelch
normal.
8
English
– Toggles squelch level between tight and
The PTT button on the
side of the radio serves
two basic purposes:
• While a call is in
progress, the PTT
button allows the radio
to transmit to other
radios in the call.
PTT
Button
Press and hold down
PTT button to talk.
Release the PTT
button to listen.
The microphone is
activated when the PTT button is pressed.
• While a call is not in progress, the PTT button is used to make
a new call (see Making a Radio Call on page 17).
Depending on programming, if the Talk Permit Tone or the PTT
Sidetone
is enabled, wait until the short alert tone ends
before talking.
You will also hear the Channel Free Indication tone if your
call is interrupted, for example when the radio receives an
Emergency Call.
You can turn off the Channel Free Indication tone or the
PTT Sidetone
by disabling all radio tones and alerts
(see Turning Radio Tones/Alerts On or Off on page 36).
Switching Between Conventional Analog
and Digital Mode
Each channel in your radio
can be configured as a
conventional analog or
conventional digital channel.
Use the Channel Selector
Knob to switch between an
analog or a digital channel.
Channel Selector Knob
When switching from digital
to analog mode, certain
features are unavailable.
Your radio also has features available in both analog and digital
mode. However, the minor differences in the way each feature
works does NOT affect the performance of your radio.
Identifying Radio Controls
During a call, if the Channel Free Indication feature is
enabled on your radio (programmed by your dealer), you
will hear a short alert tone the moment the target radio (the
radio that is receiving your call) releases the PTT button,
indicating the channel is free for you to respond.
NOTE: Your radio also switches between digital and analog
modes during a dual mode scan (see Scan on
page 24).
9
English
Switching Between Internal and External
Speakers
The BluetoothTM adaptor connected to the radio through the
universal connector provides BluetoothTM connectivity for
wireless audio routing between your radio and off-the-shelf
BluetoothTM headset.
Identifying Radio Controls
You hear a momentary tone, if a BluetoothTM link is established
or disconnected successfully between a BluetoothTM adaptor
and a BluetoothTM device.
Press the Audio Routing button to switch between an internal
or an external speaker and a tone sounds. If you press the
Audio Routing button when the BluetoothTM link is
disconnected, a negative indicator tone sounds.
10
English
Capacity Plus
Capacity Plus is a single-site trunking configuration of the
MOTOTRBO radio system, which uses a pool of channels to
support hundreds of users and up to 254 Groups. This feature
allows your radio to efficiently utilize the available number of
programmed channels while in Repeater Mode.
You can only access channel(s) with Capacity Plus via the
Channel Selector Knob, while features supported in Capacity
Plus can be accessed via a programmable button press.
You will hear a negative indicator tone if you access a feature
not applicable to Capacity Plus via a programmable button
press.
Your radio also has features that are available in both
conventional digital mode and Capacity Plus. However, the
minor differences in the way each feature works does NOT
affect the performance of your radio.
Check with your dealer or system administrator for more
information on this system.
Identifying Status Indicators
LED Indicator
The LED indicator shows the
operational status of your radio.
Blinking red – Radio is
transmitting at low battery
condition, receiving an
emergency transmission or has
failed the self-test upon
powering up.
Solid yellow – Radio is
monitoring a channel. Also
indicates fair battery charge
when the programmed Battery
Strength button is pressed.
Blinking yellow – Radio is
scanning for activity or
receiving a Call Alert.
site.
Double blinking yellow – Radio is no longer connected to the
repeater while in Capacity Plus, all Capacity Plus channels are
currently busy, or in locked state.
Solid green – Radio is transmitting. Also indicates full charge of
the battery when the programmed Battery Strength button is
pressed.
Blinking green – Radio is powering up, receiving a nonprivacy-enabled call or data, or detecting activity over the air.
LED Indicator
Rapidly blinking green – Radio is receiving a privacy-enabled
call or data.
NOTE: While in conventional mode, when the LED blinks
green, it indicates the radio detects activity over the air.
Due to the nature of the digital protocol, this activity
may or may not affect the radio's programmed
channel.
Identifying Status Indicators
Your radio indicates its operational status through the following:
LED Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 11
Audio Tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12
Indicator Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12
Rapidly blinking yellow – Radio is actively searching for a new
For Capacity Plus, there is no LED indication when the
radio is detecting activity over the air.
Upon a PTT button press, if the radio is programmed
for polite operation, the radio automatically determines
whether a transmission is permitted via a Talk Permit
or a Talk Denial tone.
11
English
Audio Tones
Alert tones provide you with audible indications of the radio’s
status or the radio’s response to data received.
Continuous Tone A monotone sound. Sounds
continuously until termination.
Identifying Status Indicators
Periodic Tone
Repetitive Tone
Sounds periodically depending on the
duration set by the radio. Tone starts,
stops, and repeats itself.
A single tone that repeats itself until it is
terminated by the user.
Momentary Tone Sounds only once for a short period of
time defined by the radio.
12
English
Indicator Tones
High pitched tone
Low pitched tone
Positive Indicator Tone
Negative Indicator Tone
Receiving and Making Calls
Selecting a Site
A site is a specific area where a base station is placed to
provide optimal coverage for the radio.
Use this navigation guide to familiarize yourself with the basic
Call features:
Selecting a Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13
Selecting a Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13
Selecting a Radio Channel, Subscriber ID,
or Group ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 14
Receiving and Responding to a Radio Call . . . . . . . . . page 14
Making a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . . page 17
Stopping a Radio Call . . . . . . . . . . . . . . . . . . . . . . . . . page 21
Talkaround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 21
Monitoring Features. . . . . . . . . . . . . . . . . . . . . . . . . . . page 22
If enabled, your radio is able to connect to different available
sites via an Internet Protocol (IP) network.
See IP Site Connect on page 32 for more information.
Selecting a Zone
A zone is a group of channels. Your radio supports up to a
maximum of 2 zones, with a maximum of 16 channels per zone.
Procedure:
1 Press the programmed Zone button.
2 You hear a positive indicator tone, indicating the radio has
switched from Zone 1 to Zone 2.
OR
You hear a negative indicator tone, indicating the radio has
switched from Zone 2 to Zone 1.
Receiving and Making Calls
Once you understand how your MOTOTRBO Portable is
configured, you are ready to use your radio.
13
English
Selecting a Radio Channel, Subscriber ID,
or Group ID
Receiving and Responding to a Radio Call
Once the channel, subscriber ID, or group ID is set, you can
proceed to receive and respond to calls.
Receiving and Making Calls
LED Indicator
Procedure:
Once the required zone is set (if you have multiple zones in
your radio), turn the Channel Selector Knob to select the
number that represents the channel, subscriber ID, or group
ID.
14
English
The LED lights up solid green while the radio is transmitting and
blinks when the radio is receiving.
NOTE: The LED lights up solid green while the radio is
transmitting and blinks green rapidly when the radio is
receiving a privacy-enabled call.
To unscramble a privacy-enabled call, your radio
must have the same Privacy Key, OR the same Key
Value and Key ID (programmed by your dealer) as
the transmitting radio (the radio you are receiving
the call from).
See Privacy on page 31 for more information.
Receiving and Responding to a Group Call
1 The LED blinks green.
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
3
If the Channel Free Indication feature is enabled, you
will hear a short alert tone the moment the transmitting radio
releases the PTT button, indicating the channel is free for
you to respond.
Press the PTT button to respond to the call.
OR
If the Voice Interrupt feature is enabled, press the PTT
button to stop the current call from the transmitting radio and
free the channel for you to talk/respond.
7 If there is no voice activity for a predetermined period of
time, the call ends.
See Making a Group Call on page 17 for details on making a
Group Call.
Receiving and Responding to a Private Call
A Private Call is a call from an individual radio to another
individual radio.
There are two types of Private Calls. The first type, where a
radio presence check is performed prior to setting up the call,
while the other sets up the call immediately.
When your radio is checked, the LED blinks green.
Only one of these call types can be programmed to your radio
by your dealer.
4 The LED lights up solid green.
Procedure:
5 Wait for the Talk Permit Tone to finish (if enabled) and speak
When you receive a private call:
clearly into the microphone.
OR
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the microphone.
Receiving and Making Calls
To receive a call from a group of users, your radio must be
configured as part of that group.
6 Release the PTT button to listen.
1 The LED blinks green.
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
15
English
3 If the Channel Free Indication feature is enabled, you will
Receiving and Making Calls
hear a short alert tone the moment the transmitting radio
releases the PTT button, indicating the channel is free for
you to respond.
Press the PTT button to respond to the call.
OR
If the Voice Interrupt feature is enabled, press the PTT
button to stop the current call from the transmitting radio and
free the channel for you to talk/respond.
4 Press the PTT button to respond to the call. The LED lights
up solid green.
5 Wait for the Talk Permit Tone to finish (if enabled) and speak
clearly into the microphone.
6 Release the PTT button to listen.
7 If there is no voice activity for a predetermined period of
time, the call ends.
8 You hear a short tone.
See Making a Private Call on page 18 for details on making a
Private Call.
16
English
Receiving an All Call
An All Call is a call from an individual radio to every radio on the
channel. It is used to make important announcements requiring
the user’s full attention.
Procedure:
When you receive an All Call:
1 A tone sounds and the LED blinks green.
2 If there is no voice activity for a predetermined period of
time, the All Call ends.
If the Channel Free Indication feature is enabled, you
will hear a short alert tone the moment the transmitting radio
releases the PTT button, indicating the channel is now
available for use.
You cannot respond to an All Call.
NOTE: The radio stops receiving the All Call if you switch to a
different channel while receiving the call.
During an All Call, you will not be able to use any
programmed button functions until the call ends.
Receiving and Responding to a Phone Call
Phone Call as Group/Private/All Call
Procedure:
When you receive a Phone Call as a Group/Private/All Call:
1 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
2 Press the PTT button to talk and release it to listen.
NOTE: When you receive a Phone Call as an All Call, you can
respond to the call or end the call, only if an All Call
type is assigned to the channel.
You can select a channel, subscriber ID or group ID by using:
• The Channel Selector Knob
• A programmed One Touch Access button
NOTE: Your radio must have the Privacy feature enabled on
the channel to send a privacy-enabled transmission.
Only target radios with the same Privacy Key OR the
same Key Value and Key ID as your radio will be able
to unscramble the transmission.
See Privacy on page 31 for more information.
Making a Call with the Channel Selector Knob
Making a Group Call
To make a call to a group of users, your radio must be
configured as part of that group.
Receiving and Making Calls
NOTE: If Phone Call capability is enabled, you are able to
respond to a Phone Call. Check with your dealer or
system administrator for more information.
Making a Radio Call
Procedure:
1 Turn the Channel Selector Knob to select the channel with
the active group ID.
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
17
English
3 Press the PTT button to make the call. The LED lights up
solid green.
4 Wait for the Talk Permit Tone to finish (if enabled) and speak
clearly into the microphone.
OR
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the microphone.
Receiving and Making Calls
5 Release the PTT button to listen. When the target radio
responds, the LED blinks green.
6 If the Channel Free Indication feature is enabled, you will
hear a short alert tone the moment the target radio releases
the PTT button, indicating the channel is free for you to
respond. Press the PTT button to respond.
OR
If there is no voice activity for a predetermined period of
time, the call ends.
18
English
Making a Private Call
While you can receive and/or respond to a Private Call
initiated by an authorized individual radio, your radio
must be programmed for you to initiate a Private Call.
You will hear a negative indicator tone, when you make a
Private Call via the One Touch Access button or the Channel
Selector Knob, if this feature is not enabled.
Use the Quick Text Message or Call Alert features to contact an
individual radio. See Text Messaging Features on page 30 or
Call Alert Operation on page 26 for more information.
Procedure:
1 Turn the Channel Selector Knob to select the channel with
the active subscriber ID.
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
3 Press the PTT button to make the call. The LED lights up
solid green.
4 Wait for the Talk Permit Tone to finish (if enabled) and speak
clearly into the microphone.
5 Release the PTT button to listen. When the target radio
responds, the LED blinks green.
hear a short alert tone the moment the target radio releases
the PTT button, indicating the channel is free for you to
respond. Press the PTT button to respond.
OR
If there is no voice activity for a predetermined period of
time, the call ends.
7 You hear a short tone.
Making an All Call
This feature allows you to transmit to all users on the channel.
Your radio must be programmed to allow you to use this feature.
Procedure:
1 Turn the Channel Selector Knob to select the channel with
the active All Call group ID.
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
3 Press the PTT button to make the call. The LED lights up
speak clearly into the microphone.
OR
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the microphone.
Users on the channel cannot respond to an All Call.
Making a Call with the One Touch Access
Button
The One Touch Access feature allows you to make a Group,
Private or Phone Call to a predefined ID easily. This feature can
be assigned to a short or long programmable button press.
You can ONLY have one ID assigned to a One Touch Access
button. Your radio can have multiple One Touch Access
buttons programmed.
Making a Group or Private Call
Receiving and Making Calls
6 If the Channel Free Indication feature is enabled, you will
4 Wait for the Talk Permit Tone to finish (if enabled) and
Procedure:
1 Press the programmed One Touch Access button to make
a Group or Private Call to the predefined ID.
solid green.
19
English
2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
3 Press the PTT button to make the call. The LED lights up
solid green.
4 Wait for the Talk Permit Tone to finish (if enabled) and
Receiving and Making Calls
speak clearly into the microphone.
OR
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the microphone.
5 Release the PTT button to listen. When the target radio
responds, the LED blinks green.
6 If the Channel Free Indication feature is enabled, you will
hear a short alert tone the moment the target radio releases
the PTT button, indicating the channel is free for you to
respond. Press the PTT button to respond.
OR
If there is no voice activity for a predetermined period of
time, the call ends.
For a Private Call, you hear a short tone when the call ends.
20
English
Making a Phone Call
NOTE: When you attempt to make or end a Phone Call without
the access and deaccess codes preconfigured, the
attempt fails and a negative indicator tone sounds.
Procedure:
1 Press the programmed One Touch Access button to make
a Phone Call to the predefined ID.
If the entry for the One Touch Access button is empty, a
negative indicator tone sounds.
2 If successful:
The DTMF tone sounds. You hear the dialing tone of the
telephone user.
OR
If unsuccessful:
A negative indicator tone sounds and the Phone Call
attempt fails. Repeat Step 1.
3 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
4 Press the PTT button to talk and release it to listen.
5 Press the programmed Phone Exit button to end the call
and a DTMF tone sounds.
6 If successful:
A tone sounds and your radio exits the Phone Call.
OR
For a Phone Call, you hear a short tone when making the call
fails.
Stopping a Radio Call
This feature allows you to stop an ongoing Group or Private Call
to free the channel for transmission. For example, when a radio
experiences a “stuck microphone” condition where the PTT
button is inadvertently pressed by the user.
Your radio must be programmed to allow you to use this feature.
Procedure:
While on the required channel:
1 Press the programmed Transmit Interrupt Remote Dekey
button.
Your radio sounds a negative indicator tone until you release
the PTT button, if it is transmitting an interruptible call that is
stopped via this feature.
Talkaround
You can continue to communicate when your repeater is not
operating, or when your radio is out of the repeater’s range but
within talking range of other radios. This is called “talkaround”.
NOTE: This feature is not applicable in Capacity Plus.
Procedure:
1 Press the programmed Repeater/Talkaround button.
2 You hear a positive indicator tone, indicating the radio is in
Talkaround mode.
OR
You hear a negative indicator tone, indicating the radio is in
Repeater mode.
Receiving and Making Calls
If unsuccessful:
A negative indicator tone sounds and your radio returns to
the Phone Call. Repeat Step 5 or wait for the telephone user
to end the call.
The Talkaround setting is retained even after powering down.
2 Wait for acknowledgment.
3 The radio sounds a positive indicator tone, indicating that
the channel is now free.
OR
The radio sounds a negative indicator tone, indicating that
the radio is unable to free the channel.
21
English
Monitoring Features
Monitoring a Channel
Use the Monitor feature to make sure a channel is free before
transmitting.
Procedure:
1 Press and hold the programmed Monitor button and listen
Receiving and Making Calls
for activity.
2 You hear radio activity or total silence, depending on how
your radio is programmed.
3 When you hear “white noise” (that is, the channel is free),
press the PTT button to talk and release it to listen. The LED
lights up solid yellow.
22
English
Permanent Monitor
Use the Permanent Monitor feature to continuously monitor a
selected channel for activity.
NOTE: This feature is not applicable in Capacity Plus.
Procedure:
1 Press the programmed Permanent Monitor button.
2 Radio sounds alert tone, and the LED lights up solid yellow.
3 Press the programmed Permanent Monitor button to
remove the radio from permanent monitor mode.
4 Radio sounds an alert tone and the LED turns off.
Scan Lists
Advanced Features
Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Indicator Settings . . . . . . . . . . . . . . . . . . . . . . . . .
Call Alert Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . .
Text Messaging Features . . . . . . . . . . . . . . . . . . . . . .
Privacy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IP Site Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lone Worker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Password Lock Features . . . . . . . . . . . . . . . . . . . . . . .
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page 23
page 24
page 25
page 26
page 27
page 30
page 31
page 35
page 33
page 34
page 35
Scan lists are created and assigned to individual channels/
groups. Your radio scans for voice activity by cycling through
the channel/group sequence specified in the scan list for the
current channel.
Your radio supports up to 250 scan lists, with a maximum of 16
members in a list. Each scan list shall support a mixture of both
analog and digital entries.
NOTE: This feature is not applicable in Capacity Plus.
Advanced Features
Use this navigation guide to learn more about advanced
features available with your radio:
23
English
Scan
When you start a scan, your radio cycles through the
programmed scan list for the current channel looking for voice
activity.
The LED blinks yellow.
During a dual mode scan, if you are on a digital channel, and
your radio locks onto an analog channel, it automatically
switches from digital mode to analog mode for the duration of
the call. This is also true for the reverse.
There are two types of scans:
Advanced Features
• Main Channel Scan (Manual): Your radio scans all the
channels/groups in your scan list. On entering scan, your
radio may – depending on the settings – automatically start
on the last scanned “active” channel/group or on the channel
where scan was initiated.
• Auto Scan (Automatic): Your radio automatically starts
scanning when you select a channel/group that has Auto
Scan enabled.
NOTE: This feature is not applicable in Capacity Plus.
24
English
Starting and Stopping Scan
Procedure:
1 Press the programmed Scan button.
OR
Use the Channel Selector Knob to select a channel with
Auto Scan enabled.
2 When Scan is enabled, the LED blinks yellow and you hear
a positive indicator tone.
OR
When Scan is disabled, the LED turns off and you hear a
negative indicator tone.
Responding to a Transmission During a Scan
During scanning, your radio stops on a channel/group where
activity is detected. The radio stays on that channel for a
programmed time period known as “hang time”.
Procedure:
1 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
If the Channel Free Indication feature is enabled, you
will hear a short alert tone the moment the transmitting radio
releases the PTT button, indicating the channel is free for
you to respond.
2 Press the PTT button during hang time. The LED lights up
solid green.
speak clearly into the microphone.
OR
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the microphone.
4 Release the PTT button to listen.
5 If you do not respond within the hang time, the radio returns
to scanning other channels/groups.
Procedure:
To restore the deleted nuisance channel, do one of the
following:
• Turn the radio off and power it on again, OR
• Stop and restart a scan via the programmed Scan button, OR
• Change the channel via the Channel Selector Knob.
Call Indicator Settings
Deleting a Nuisance Channel
You can turn on or off the ringing tones for a received Private
Call (see Turning Radio Tones/Alerts On or Off on page 36).
If a channel continually generates unwanted calls or noise
(termed a “nuisance” channel), you can temporarily remove the
unwanted channel from the scan list.
Escalating Alarm Tone Volume
This capability does not apply to the channel designated as the
Selected Channel.
Your radio can be programmed by your dealer to continually
alert you when a radio call remains unanswered. This is done
by automatically increasing the alarm tone volume over time.
Procedure:
This feature is known as Escalert.
Advanced Features
3 Wait for the Talk Permit Tone to finish (if enabled) and
Restoring a Nuisance Channel
1 When your radio “locks on to” an unwanted or nuisance
channel, press the programmed Nuisance Channel Delete
button until you hear a tone.
2 Release the Nuisance Channel Delete button. The
nuisance channel is deleted.
25
English
Call Alert Operation
Call Alert paging enables you to alert a specific radio user to call
you back when they are able to do so. This feature is accessible
via a programmed One Touch Access button.
Receiving and Responding to a Call Alert
Procedure:
When you receive a Call Alert page:
1 You hear a repetitive tone. The LED blinks yellow.
2 Press the PTT button within four (4) seconds of receiving a
Advanced Features
Call Alert page to respond to the Private Call.
26
English
Making a Call Alert with the One Touch Access
Button
Procedure:
1 Press the programmed One Touch Access button to make
a Call Alert to the predefined ID.
2 The LED lights up solid green when your radio is sending
the Call Alert.
3 If the Call Alert acknowledgement is received, two chirps
sound.
OR
If the Call Alert acknowledgement is not received, a lowpitch tone sounds.
Emergency Operation
Your dealer can set the duration of a button press for the
programmed Emergency button, except for long press, which is
similar with all other buttons:
• Short press – Between 0.05 seconds and 0.75 seconds
• Long press – Between 1.00 second and 3.75 seconds
The Emergency button is assigned with the Emergency On/Off
feature. Check with your dealer for the assigned operation of
the Emergency button.
• Regular – Radio transmits an alarm signal and shows audio
and/or visual indicators.
• Silent – Radio transmits an alarm signal without any audio or
visual indicators. Radio receives calls without any sound
through the radio’s speaker, until you press the PTT button to
initiate the call.
• Silent with Voice – Radio transmits an alarm signal without
any audio or visual indicators, but allow incoming calls to
sound through the radio’s speaker.
Only one of the Emergency Alarms above can be assigned to
the programmed Emergency button.
Sending an Emergency Alarm
If short press the Emergency button is assigned to turn on the
Emergency mode, then long press the Emergency button is
assigned to exit the Emergency mode.
This feature allows you to send an Emergency Alarm, a nonvoice signal, which triggers an alert indication on a group of
radios.
If long press the Emergency button is assigned to turn on the
Emergency mode, then short press the Emergency button is
assigned to exit the Emergency mode.
Procedure:
Your radio supports three Emergency Alarms:
Advanced Features
An Emergency Alarm is used to indicate a critical situation. You
are able to initiate an Emergency at any time, in any state, even
when there is activity on the current channel.
In addition, each alarm has the following types:
1 Press the programmed Emergency On button.
2 The LED lights up solid green.
• Emergency Alarm
• Emergency Alarm with Call
• Emergency Alarm with Voice to Follow
27
English
3 When an Emergency Alarm acknowledgment is received,
the Emergency tone sounds. The LED blinks green.
OR
If your radio does not receive an Emergency Alarm
acknowledgement, and after all retries have been
exhausted, a low-pitch tone sounds.
4 Radio exits the Emergency Alarm mode.
If your radio is set to Silent, it will not display any audio or visual
indicators during Emergency mode.
Advanced Features
Sending an Emergency Alarm with Call
This feature allows you to send an Emergency Alarm to a group
of radios. Upon acknowledgement by a radio within the group,
the group of radios can communicate over a programmed
Emergency channel.
Procedure:
1 Press the programmed Emergency On button.
2 The LED lights up solid green.
3 When an Emergency Alarm acknowledgment is received,
the Emergency tone sounds. The LED blinks green.
4 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
5 Press the PTT button to make the call. The LED lights up
28
solid green.
English
6 Wait for the Talk Permit Tone to finish (if enabled) and
speak clearly into the microphone.
OR
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the microphone.
7 Release the PTT button to listen.
8 When the channel is free for you to respond, a short alert
tone sounds (
if the Channel Free Indication feature is
enabled). Press the PTT button to respond.
OR
Once your call ends, press Emergency Off button to exit
the Emergency mode.
If your radio is set to Silent, it will not display any audio or visual
indicators during Emergency mode, or allow any received calls
to sound through the radio’s speaker, until you press the PTT
button to initiate the call.
If your radio is set to Silent with Voice, it will not display any
audio or visual indicators during Emergency mode, but allow
incoming calls to sound through the radio’s speaker. The
indicators will only appear once you press the PTT button to
initiate, or respond to, the call.
Sending an Emergency Alarm with Voice to
This feature allows you to send an Emergency Alarm to a group
of radios. Your radio’s microphone is automatically activated,
allowing you to communicate with the group of radios without
pressing the PTT button.
This activated microphone state is also known as “hot mic”.
If you press the PTT button during the programmed hot mic
transmission period, the radio ignores the PTT press and
remains in Emergency mode.
NOTE: If you press the PTT button during hot mic, and
continue to press it after the hot mic duration expires,
the radio continues to transmit until you release the
PTT button.
Procedure:
1 Press the programmed Emergency On button.
stops transmitting. To transmit again, press the PTT button
If your radio is set to Silent, it will not display any audio or visual
indicators during Emergency mode, or allow any received calls
to sound through the radio’s speaker, until the programmed hot
mic transmission period is over, and you press the PTT button.
If your radio is set to Silent with Voice, it will not display any
audio or visual indicators during Emergency mode when you
are making the call with hot mic, but allow sound through the
radio’s speaker when the target radio responds after the
programmed hot mic transmission period is over. The indicators
will only appear when you press the PTT button.
NOTE: If the Emergency Alarm request fails, the radio does
not retry to send the request, and enters the hot mic
state directly.
Reinitiating an Emergency Mode
2 The LED lights up solid green.
NOTE: This feature is only applicable to the radio sending the
Emergency Alarm.
3 Once a tone sounds, speak clearly into the microphone.
There are two instances where this can happen:
When hot mic has been enabled, the radio automatically
transmits without a PTT press until the hot mic duration
expires.
4 While transmitting, the LED lights up solid green.
Advanced Features
Follow
5 Once the hot mic duration expires, the radio automatically
• You change the channel while the radio is in Emergency
mode. This exits the Emergency mode. If Emergency Alarm
is enabled on this new channel, the radio reinitiates
Emergency.
29
English
• You press the programmed Emergency On button during an
Emergency initiation/transmission state. This causes the
radio to exit this state, and to reinitiate Emergency.
Exiting an Emergency Mode
NOTE: This feature is only applicable to the radio sending the
Emergency Alarm.
Your radio exits Emergency mode when one of the following
occurs:
• Emergency Alarm acknowledgement is received (for
Emergency Alarm only), OR
Advanced Features
• All retries to send the alarm have been exhausted, OR
• The Emergency Off button is pressed.
NOTE: If your radio is powered off, it exits the Emergency
mode. The radio will not reinitiate the Emergency
mode automatically when it is turned on again.
30
English
Text Messaging Features
Sending a Quick Text Message
You can send Quick Text messages, programmed by your
dealer, via the programmable button.
Procedure:
1 Press the programmed One Touch Access button to send
a predefined Quick Text message to a predefined ID.
2 The LED lights up solid green.
3 Two chirps indicate that the message is sent successfully.
OR
A low-pitch tone indicates that the message cannot be sent.
Privacy
Your radio must have privacy enabled on the channel to send a
privacy-enabled transmission, although this is not a necessary
requirement for receiving a transmission. While on a privacyenabled channel, the radio is still able to receive clear
(unscrambled) transmissions.
Your radio supports two types of privacy:
• Basic Privacy
The LED lights up solid green while the radio is transmitting and
blinks green rapidly when the radio is receiving an ongoing
privacy-enabled transmission.
NOTE: Some radio models may not offer this Privacy feature.
Check with your dealer or system administrator for
more information.
Procedure:
Press the programmed Privacy button to toggle privacy on or
off.
Advanced Features
If enabled, this feature helps to prevent eavesdropping by
unauthorized users on a channel by the use of a softwarebased scrambling solution. The signaling and user identification
portions of a transmission are not scrambled.
If your radio receives a scrambled call that is of a different
Privacy Key, OR a different Key Value and Key ID, you will
either hear a garbled transmission (Basic Privacy) or nothing at
all (Enhanced Privacy).
• Enhanced Privacy
Only ONE of the privacy types above can be assigned to the
radio.
To unscramble a privacy-enabled call or data transmission, your
radio must be programmed to have the same Privacy Key (for
Basic Privacy), OR the same Key Value and Key ID (for
Enhanced Privacy) as the transmitting radio.
31
English
Advanced Features
IP Site Connect
A Members list supports a maximum of 16 channels (including
the Selected Channel).
This feature allows your radio to extend communication beyond
the reach of a single site, by connecting to different available
sites via an Internet Protocol (IP) network.
NOTE: You cannot manually add or delete an entry to the
Members list. Check with your dealer or system
administrator for more information.
NOTE: This feature is not applicable in Capacity Plus.
Starting an Automatic Site Search
When the radio moves out of range from one site and into the
range of another, it connects to the new site's base station to
send or receive calls/data transmissions. Depending on your
settings, this is done automatically or manually.
NOTE: The radio only scans for a new site if the current signal
is weak or when the radio is unable to detect any signal
from the current site. If the RSSI value is strong, the
radio remains on the current site.
If the radio is set to do this automatically, it scans through all
available sites when the signal from the current site is weak or
when the radio is unable to detect any signal from the current
site. It then locks on to the base station with the strongest
Received Signal Strength Indicator (RSSI) value.
Procedure:
In a manual site search, the radio searches for the next site in
the roam list that is currently in range (but which may not have
the strongest signal) and locks on to it.
NOTE: Each channel can only have either Scan or Roam
enabled, not both at the same time.
Channels with this feature enabled can be added to a particular
roam list. The radio searches the channel(s) in the Members list
during the automatic roam operation to locate the best site.
32
English
1 Press the programmed Site Lock On/Off button.
2 A tone sounds.
3 The LED blinks yellow rapidly when the radio is actively
searching for a new site, and turns off once the radio locks
on to a site.
The radio also performs an automatic site search (site is
unlocked) during a PTT button press or data transmission if
the current channel, an IP Site Select channel with an attached
roam list, is out of range.
Stopping an Automatic Site Search
Procedure:
1 Press the programmed Site Lock On/Off button.
2 A tone sounds and the LED turns off.
Starting a Manual Site Search
Procedure:
1 Press the programmed Manual Site Roam button.
This feature prompts an emergency to be raised if there is no
user activity, such as any radio button press or activation of the
channel selector, for a predefined time.
Following no user activity for a programmed duration, the radio
pre-warns the user via an audio indicator once the inactivity
timer expires.
If there is still no acknowledgment by the user before the
predefined reminder timer expires, the radio initiates an
Emergency Alarm.
2 A tone sounds and the LED blinks green.
Only one of the following Emergency Alarms is assigned to this
feature:
3 You hear a positive indicator tone and the LED turns off,
• Emergency Alarm
indicating the radio is locked on to a site.
OR
You hear a negative indicator tone and the LED turns off,
indicating the radio is unable to lock on to a site.
Advanced Features
When the radio is actively searching for a new site:
Lone Worker
• Emergency Alarm with Call
• Emergency Alarm with Voice to Follow
The radio remains in the emergency state allowing voice
messages to proceed until action is taken. See Emergency
Operation on page 27 on ways to exit Emergency.
NOTE: This feature is limited to radios with this function
enabled. Check with your dealer or system
administrator for more information.
33
English
Password Lock Features
If enabled, this feature allows you to access your radio via
password upon powering up. Use the Channel Selector Knob
and the three Side Buttons to enter password (see Radio
Controls of page 6):
• Channel Selector Knob positions 1 to 9 represent
numbers 1 to 9, and position 10 represents number 0.
• Side Buttons 1 to 3 represent numbers 1 to 3.
Accessing the Radio from Password
Advanced Features
Procedure:
Power up the radio.
34
1 You hear a continuous tone.
2 Use the Channel Selector Knob to enter the first digit of the
password.
3 Press Side Button 1, 2 or 3 to enter each digit of the
remaining three digits of the password. You hear a positive
indicator tone for each Side Button press.
When the second digit of the password is entered, your
radio ignores any Channel Selector Knob position change.
4 When the last digit of the four-digit password is entered,
your radio automatically checks the validity of the password.
If the password is correct:
Your radio proceeds to power up. See Powering Up the
English
Radio on page 5.
OR
If the password is incorrect:
You hear a continuous tone. Repeat Steps 1 to 3.
OR
After the third incorrect password, your radio enters into
locked state. A tone sounds and the LED double blinks
yellow.
Your radio enters into locked state for 15 minutes, and responds
to inputs from On/Off/Volume Control Knob.
NOTE: The radio is unable to receive any call, including
emergency calls, in locked state.
Unlocking the Radio from Locked State
Procedure:
Wait for 15 minutes. Repeat Steps 1 to 4 in Accessing the
Radio from Password on page 34.
OR
Power up the radio, if you have powered down the radio during
locked state:
1 A tone sounds and the LED double blinks yellow.
2 Wait for 15 minutes. Repeat Steps 1 to 4 in Accessing the
Radio from Password on page 34.
Your radio restarts the 15 minutes timer for locked state when
you power up.
Utilities
You can adjust your radio's squelch level to filter out unwanted
calls with low signal strength or channels that have a higher
than normal background noise.
Settings: Normal is the default. Tight filters out (unwanted)
calls and/or background noise. However, calls from remote
locations may also be filtered out.
Procedure:
1 Press the programmed Squelch button.
2 You hear a positive indicator tone, indicating the radio is
operating in tight squelch.
OR
You hear a negative indicator tone, indicating the radio is
operating in normal squelch.
You can toggle your radio’s power setting between high or low
for each channel.
Settings: High enables communication with radios located at a
considerable distance from you. Low enables communication
with radios in closer proximity.
Procedure:
1 Press the programmed Power Level button.
2 You hear a positive indicator tone, indicating the radio is
transmitting at low power.
OR
You hear a negative indicator tone, indicating the radio is
transmitting at high power.
Advanced Features
Setting the Squelch Level
Setting the Power Level
Turning the Option Board Feature(s) On or Off
A channel can support up to 6 option board features. Refer to
your dealer or system administrator for more information.
Procedure:
Press the programmed Option Board Feature button to toggle
the feature on or off.
35
English
Turning the Voice Operating Transmission (VOX)
Feature On or Off
This feature allows you to initiate a hands-free voice activated
call on a programmed channel. The radio automatically
transmits, for a programmed period, whenever the microphone
on the VOX-capable accessory detects voice.
Pressing the PTT button during radio operation will disable
VOX. To re-enable VOX, do one of the following:
• Turn the radio off and power it on again, OR
• Change the channel via the Channel Selector Knob, OR
Advanced Features
• Follow the procedure below.
NOTE: Turning this feature on or off is limited to radios with
this function enabled. Check with your dealer or system
administrator for more information.
Procedure:
Press the programmed VOX button to toggle the feature on or
off.
If the Talk Permit Tone feature is enabled, use a trigger word to
initiate the call. Wait for the Talk Permit Tone to finish before
speaking clearly into the microphone.
36
English
Turning Radio Tones/Alerts On or Off
You can enable and disable all radio tones and alerts (except
for the incoming Emergency alert tone) if needed.
Procedure:
1 Press the programmed All Tones/Alerts button.
2 You hear a positive indicator tone, indicating all tones and
alerts are on.
OR
You hear a negative indicator tone, indicating all tones and
alerts are off.
Checking the Battery Strength
You can check how much battery power you have left.
Settings: The LED Indicator in solid yellow indicates fair battery
charge while solid green indicates full charge of the battery.
Procedure:
Press the programmed Battery Strength button to view the
battery strength via the LED Indicator.
• Combination VHF/GPS, 160 – 174 MHz, Helical Antenna5
Accessories
(PMAD4069_)
• VHF Wideband, 136 – 174 MHz, Double Helical Antenna6
Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 37
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 38
Carry Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 38
Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 39
Earbuds and Earpieces . . . . . . . . . . . . . . . . . . . . . . . . page 39
Headsets and Headset Accessories . . . . . . . . . . . . . . page 39
Remote Speaker Microphones . . . . . . . . . . . . . . . . . . page 40
Surveillance Accessories. . . . . . . . . . . . . . . . . . . . . . . page 40
Miscellaneous Accessories . . . . . . . . . . . . . . . . . . . . . page 41
• VHF, 136 – 147 MHz, Stubby Antenna4 (PMAD4093_)
• Combination UHF/GPS, 403 – 433 MHz, Folded Monopole
Antenna1 (PMAE4018_)
• Combination UHF/GPS, 403 – 433 MHz, Stubby Antenna1
(PMAE4021_)
• UHF1, 403 – 470 MHz, Whip Antenna3 (PMAE4022_)
• Combination UHF1/GPS, 430 – 470 MHz, Folded Monopole
Antenna2 (PMAE4024_)
Antenna4
(PMAD4067_)
(PMAD4068_)
• VHF, 160 – 174 MHz, Stubby Antenna5 (PMAD4095_)
(PMAE4023_)
The diagram on the right shows the location of
the color indicator for the following antennas. See
the footnote at the end of the list for the colors.
• Combination VHF/GPS, 147 – 160 MHz, Helical
• VHF, 147 – 160 MHz, Stubby Antenna3 (PMAD4094_)
• Combination UHF1/GPS, 430 – 470 MHz, Stubby Antenna2
Antennas
• Combination VHF/GPS, 136 – 147 MHz, Helical
(PMAD4088_)
Accessories
Your radio is compatible with the accessories listed in this
chapter. Contact your dealer for details.
Antenna3
• Combination UHF2/GPS, 450 – 527 MHz, Stubby Antenna7
(PMAE4048_)
• UHF2, 450 – 527 MHz, Whip Antenna7 (PMAE4049_)
• Combination UHF2/GPS, 450 – 495 MHz, Folded Monopole
Antenna8 (PMAE4050_)
37
English
• Combination UHF2/GPS, 495 – 527 MHz, Folded Monopole
• IMPRES Li-Ion, 2200 mAh Submersible (IP57) Battery
(PMNN4077_)
Antenna6 (PMAE4051_)
• Combination 800/900/GPS, 806 – 941 MHz, Helical Antenna9
• NiMH, 1300 mAh Submersible (IP57) Battery (PMNN4065_)*
(PMAF4003_)
* Not applicable to the 800/900 band.
• Public Safety Microphone UHF Stubby Antenna1,
403 – 433 MHz (PMAE4046_)
Carry Devices
• Public Safety Microphone UHF Stubby Antenna2,
430 – 470 MHz (PMAE4047_)
• Belt Clip for 2-Inch Belt Width (PMLN4651_)
• Public Safety Microphone VHF Antenna5,
• Belt Clip for 2.5-Inch Belt Width (PMLN4652_)
150 – 174 MHz (PMAD4086_)
• 2.5-Inch Replacement Swivel Belt Loop (PMLN5022_)
• Public Safety Microphone VHF Antenna4,
Accessories
136 – 153 MHz (PMAD4087_)
• 3-Inch Replacement Swivel Belt Loop (PMLN5023_)
• Nylon Carry Case with 3-Inch Fixed Belt Loop for
Color Code:
1 Red
3 Black
5 Blue
7 Brown
2 Green
4 Yellow
6 White
8 Orange
9 Purple
Non-Display Radio (PMLN5024_)
• Soft Leather Carry Case with 2.5-Inch Swivel Belt Loop for
Non-Display Radio (PMLN5025_)
Batteries
• IMPRES Li-Ion, 1500 mAh Submersible (IP57) Battery
(PMNN4066_)*
• IMPRES Li-Ion, 1400 mAh Submersible (IP57) Battery,
Intrinsically Safe (FM) (PMNN4069_)
38
English
• Soft Leather Carry Case with 3-Inch Swivel Belt Loop for
Non-Display Radio (PMLN5026_)
• Soft Leather Carry Case with 3-Inch Fixed Belt Loop for
Non-Display Radio (PMLN5027_)
• Hard Leather Carry Case with 2.5-Inch Swivel Belt Loop for
Non-Display Radio (PMLN5028_)
• Hard Leather Carry Case with 3-Inch Swivel Belt Loop for
Non-Display Radio (PMLN5029_)
• Hard Leather Carry Case with 3-Inch Fixed Belt Loop for
Non-Display Radio (PMLN5030_)
Chargers
• IMPRES Vehicular Charger (NNTN7616_)
• IMPRES Multi-Unit Charger (WPLN4212_)
• IMPRES Multi-Unit Charger with Displays (WPLN4219_)
• IMPRES Single-Unit Charger (WPLN4232_)
(RLN4761_)
• Large Custom Earpiece for Surveillance Kits, Right Ear
Accessories
• 1.75-Inch Black Leather Belt (4200865599)
• Medium Custom Earpiece for Surveillance Kits, Right Ear
(RLN4762_)
• Small Custom Earpiece for Surveillance Kits, Left Ear
(RLN4763_)
• Medium Custom Earpiece for Surveillance Kits, Left Ear
(RLN4764_)
• Large Custom Earpiece for Surveillance Kits, Left Ear
(RLN4765_)
• Standard Earpiece, Black (RLN6279_)
• Standard Earpiece, Beige (RLN6280_)
Earbuds and Earpieces
• Replacement Foam Ear Pad and Windscreen (RLN6283_)
• Receive-Only Earbud (AARLN4885_)
• D-Shell Receive-Only Earpiece (PMLN4620_)
• Earpiece with Acoustic Tube Assembly, Beige (RLN6284_)
• Receive-Only Earpiece (RLN4941_)
• Earpiece with High Noise Kit, Beige (RLN6288_)
• Over-the-Ear Receiver for Remote Speaker Microphone
• Earpiece with High Noise Kit, Black (RLN6289_)
• Earpiece with Acoustic Tube Assembly, Black (RLN6285_)
(WADN4190_)
• D-Shell Earset (PMLN5096_)
• IMPRES Temple Transducer (PMLN5101_)
• Small Custom Earpiece for Surveillance Kits, Right Ear
(RLN4760_)
Headsets and Headset Accessories
• Ultra-Lite Headset (PMLN5102_)
• Heavy Duty Noise-Canceling Headset (FM) (PMLN5275_)
• Lightweight Headset (RMN5058_)
39
English
Remote Speaker Microphones
• Remote Speaker Microphone Replacement Coil Cord Kit (For
• Remote Speaker Microphone (PMMN4024_)
• Remote Speaker Microphone Replacement Coil Cord Kit (For
• IMPRES Remote Speaker Microphone (PMMN4025_)
• Remote Speaker Microphone, Submersible (IP57)
(PMMN4040_)
• IMPRES Public Safety Microphone (PSM), 30-Inch Cable
(PMMN4041_)*
• IMPRES Public Safety Microphone (PSM), 24-Inch Cable
(PMMN4042_)*
• IMPRES Public Safety Microphone (PSM), 18-Inch Cable
(PMMN4043_)*
• IMPRES Remote Speaker Microphone, with Volume, IP57
(PMMN4046_)
Accessories
• IMPRES Submersible Public Safety Microphone, 30-Inch
Cable (PMMN4047_)*
• IMPRES Submersible Public Safety Microphone, 24-Inch
Cable (PMMN4048_)*
• IMPRES Submersible Public Safety Microphone, 18-Inch
Cable (PMMN4049_)*
• IMPRES Remote Speaker Microphone, Noise-Canceling
(PMMN4050_)
40
English
Use with PMMN4024_ and PMMN4040_) (RLN6074_)
Use with PMMN4025) (RLN6075_)
* Not applicable to the 800/900 band.
Surveillance Accessories
• IMPRES 3-Wire Surveillance, Black (PMLN5097_)
• IMPRES 3-Wire Surveillance, Beige (PMLN5106_)
• IMPRES 3-Wire Surveillance Kit with Clear, Comfortable
Acoustic Tube, Black (PMLN5111_)
• IMPRES 3-Wire Surveillance Kit with Clear, Comfortable
Acoustic Tube, Beige (PMLN5112_)
• Receive Only Surveillance Kit, Black (Single Wire)
(RLN5878_)
• Receive Only Surveillance Kit, Beige (Single Wire)
(RLN5879_)
• IMPRES 2-Wire Surveillance Kit, Black (RLN5880_)
• IMPRES 2-Wire Surveillance Kit, Beige (RLN5881_)
• IMPRES 2-Wire Surveillance Kit with Clear, Comfortable
Acoustic Tube, Black (RLN5882_)
Acoustic Tube, Beige (RLN5883_)
• Surveillance Low Noise Kit (RLN5886_)
• Surveillance High Noise Kit (RLN5887_)
Miscellaneous Accessories
• Universal Chest Pack (HLN6602_)
• Waterproof Bag, Includes Large Carry Strap (HLN9985_)
• Shoulder Strap (Attaches to D-Rings on Carry Case)
• Break-A-Way Chest Pack (RLN4570_)
• Universal RadioPAK and Utility Case (Fanny Pack)
(RLN4815_)
• Replacement Ear Tips, Clear, Pack of 25 (For Use with
RLN5886_) (RLN6282_)
• Replacement Strap for RLN4570_ and HLN6602_ Chest
Packs (1505596Z02)
Accessories
• IMPRES 2-Wire Surveillance Kit with Clear, Comfortable
• Small Clip, Epaulet Strap (RLN4295_)
• Accessory Dust Cover (1571477L01)
• Replacement Foam Plugs, Pack of 50 (For Use with
RLN5887_) (5080384F72)
• Universal RadioPAK Extension Belt (4280384F89)
(NTN5243_)
41
English
Batteries and Chargers Warranty
The workmanship warranty guarantees against defects in
Batteries and Chargers Warranty
workmanship under normal use and service.
All MOTOTRBO Batteries
Two (2) Years
IMPRES Chargers (Single-Unit and Multi-Unit,
Non-Display)
Two (2) Years
IMPRES Chargers (Multi-Unit with Display)
One (1) Year
English
The capacity warranty guarantees 80% of the rated capacity for the
warranty duration.
The Workmanship Warranty
42
The Capacity Warranty
Nickel Metal-Hydride (NiMH) or Lithium-Ion
(Li-lon) Batteries
12 Months
IMPRES Batteries, When Used Exclusively
with IMPRES Chargers
18 Months
obligations or liability for additions or modifications to this warranty
unless made in writing and signed by an officer of MOTOROLA.
Limited Warranty
I. WHAT THIS WARRANTY COVERS AND FOR HOW
LONG:
MOTOROLA SOLUTIONS, INC. (“MOTOROLA”) warrants the
MOTOROLA manufactured Communication Products listed below
(“Product”) against defects in material and workmanship under
normal use and service for a period of time from the date of
purchase as scheduled below:
XPR Series Digital Portable
Radios
Two (2) Years
Product Accessories (Excluding
Batteries and Chargers)
One (1) Year
MOTOROLA, at its option, will at no charge either repair the
Product (with new or reconditioned parts), replace it (with a new or
reconditioned Product), or refund the purchase price of the Product
during the warranty period provided it is returned in accordance
with the terms of this warranty. Replaced parts or boards are
warranted for the balance of the original applicable warranty period.
All replaced parts of Product shall become the property of
MOTOROLA.
This express limited warranty is extended by MOTOROLA to the
original end user purchaser only and is not assignable or
transferable to any other party. This is the complete warranty for the
Product manufactured by MOTOROLA. MOTOROLA assumes no
Unless made in a separate agreement between MOTOROLA and
the original end user purchaser, MOTOROLA does not warrant the
installation, maintenance or service of the Product.
MOTOROLA cannot be responsible in any way for any ancillary
equipment not furnished by MOTOROLA which is attached to or
used in connection with the Product, or for operation of the Product
with any ancillary equipment, and all such equipment is expressly
excluded from this warranty. Because each system which may use
the Product is unique, MOTOROLA disclaims liability for range,
coverage, or operation of the system as a whole under this
warranty.
Limited Warranty
MOTOROLA COMMUNICATION PRODUCTS
II. GENERAL PROVISIONS:
This warranty sets forth the full extent of MOTOROLA'S
responsibilities regarding the Product. Repair, replacement or
refund of the purchase price, at MOTOROLA’s option, is the
exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL
OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED
WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR
DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME,
INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR
SAVINGS OR OTHER INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
43
English
INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT
SUCH MAY BE DISCLAIMED BY LAW.
III. STATE LAW RIGHTS:
SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY
NOT APPLY.
This warranty gives specific legal rights, and there may be other
rights which may vary from state to state.
Limited Warranty
IV. HOW TO GET WARRANTY SERVICE:
44
You must provide proof of purchase (bearing the date of purchase
and Product item serial number) in order to receive warranty
service and, also, deliver or send the Product item, transportation
and insurance prepaid, to an authorized warranty service location.
Warranty service will be provided by MOTOROLA through one of its
authorized warranty service locations. If you first contact the
company which sold you the Product (e.g., dealer or
communication service provider), it can facilitate your obtaining
warranty service. You can also call MOTOROLA at 1-800-927-2744
US/Canada.
V. WHAT THIS WARRANTY DOES NOT COVER:
A) Defects or damage resulting from use of the Product in other
than its normal and customary manner.
B) Defects or damage from misuse, accident, water, or neglect.
English
C)Defects or damage from improper testing, operation,
maintenance, installation, alteration, modification, or adjustment.
D)Breakage or damage to antennas unless caused directly by
defects in material workmanship.
E) A Product subjected to unauthorized Product modifications,
disassembles or repairs (including, without limitation, the addition
to the Product of non-MOTOROLA supplied equipment) which
adversely affect performance of the Product or interfere with
MOTOROLA's normal warranty inspection and testing of the
Product to verify any warranty claim.
F) Product which has had the serial number removed or made
illegible.
G)Rechargeable batteries if:
(1) any of the seals on the battery enclosure of cells are broken
or show evidence of tampering.
(2) the damage or defect is caused by charging or using the
battery in equipment or service other than the Product for which it
is specified.
H)Freight costs to the repair depot.
I) A Product which, due to illegal or unauthorized alteration of the
software/firmware in the Product, does not function in
accordance with MOTOROLA’s published specifications or the
FCC certification labeling in effect for the Product at the time the
Product was initially distributed from MOTOROLA.
J) Scratches or other cosmetic damage to Product surfaces that
does not affect the operation of the Product.
K) Normal and customary wear and tear.
VI. PATENT AND SOFTWARE PROVISIONS:
Laws in the United States and other countries preserve for
MOTOROLA certain exclusive rights for copyrighted MOTOROLA
software such as the exclusive rights to reproduce in copies and
distribute copies of such MOTOROLA software. MOTOROLA
software may be used in only the Product in which the software was
originally embodied and such software in such Product may not be
replaced, copied, distributed, modified in any way, or used to
produce any derivative thereof. No other use including, without
limitation, alteration, modification, reproduction, distribution, or
reverse engineering of such MOTOROLA software or exercise of
rights in such MOTOROLA software is permitted. No license is
granted by implication, estoppel or otherwise under MOTOROLA
patent rights or copyrights.
Limited Warranty
MOTOROLA will defend, at its own expense, any suit brought
against the end user purchaser to the extent that it is based on a
claim that the Product or parts infringe a United States patent, and
MOTOROLA will pay those costs and damages finally awarded
against the end user purchaser in any such suit which are
attributable to any such claim, but such defense and payments are
conditioned on the following:
A) that MOTOROLA will be notified promptly in writing by such
purchaser of any notice of such claim;
B) that MOTOROLA will have sole control of the defense of such
suit and all negotiations for its settlement or compromise; and
C)should the Product or parts become, or in MOTOROLA’s opinion
be likely to become, the subject of a claim of infringement of a
United States patent, that such purchaser will permit
MOTOROLA, at its option and expense, either to procure for
such purchaser the right to continue using the Product or parts or
to replace or modify the same so that it becomes non-infringing
or to grant such purchaser a credit for the Product or parts as
depreciated and accept its return. The depreciation will be an
equal amount per year over the lifetime of the Product or parts as
established by MOTOROLA.
MOTOROLA will have no liability with respect to any claim of patent
infringement which is based upon the combination of the Product or
parts furnished hereunder with software, apparatus or devices not
furnished by MOTOROLA, nor will MOTOROLA have any liability
for the use of ancillary equipment or software not furnished by
MOTOROLA which is attached to or used in connection with the
Product. The foregoing states the entire liability of MOTOROLA with
respect to infringement of patents by the Product or any parts
thereof.
VII. GOVERNING LAW:
This Warranty is governed by the laws of the State of Illinois, U.S.A.
45
English
Notes
Notes
46
English
Motorola Solutions, Inc.
1303 East Algonquin Road
Schaumburg, Illinois 60196 U.S.A.
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and
the Stylized M logo are trademarks or registered trademarks
of Motorola Trademark Holdings, LLC and are used under license.
All other trademarks are the property of their respective owners.
© 2006 – 2011 Motorola Solutions, Inc. All rights reserved.
January 2011.
www.motorola.com/mototrbo
*6880309T27*
6880309T27-K