DAB / FM RDS Digital Radio with built-in battery charger

Please read this manual before use

Contents

Controls .......................................................................2-3

Battery operation using alkaline batteries.......................4

Battery operation using rechargeable batteries ...........5-6

Using the AC adaptor .....................................................6

Operating your radio - DAB ............................................7

Selecting a station - DAB................................................8

Display modes - DAB .....................................................9

Finding new stations - DAB ..........................................10

Secondary services - DAB............................................10

Manual tuning - DAB .................................................... 11

Signal strength display - DAB ....................................... 11

Dynamic range control (DRC) settings - DAB ..............12

Operating your radio - Search tuning - FM ...................13

Manual tuning - FM.......................................................14

Display modes - FM......................................................15

Favourite button............................................................16

Recalling your favourite station ....................................16

Preset stations DAB and FM ........................................17

Stereo / Mono setting - FM ...........................................18

Scan sensitivity setting - FM .........................................19

Software version ...........................................................20

System reset.................................................................21

Headphone socket........................................................22

Auxiliary input socket ....................................................22

Line out socket .............................................................22

A few words about batteries ....................................23-24

Display backlight...........................................................25

USB socket for software upgrades ...............................25

General .........................................................................26

Specifi cations ...............................................................26

Circuit features .............................................................26

Guarantee........................................................Back page

1

Controls

(Top)

12 11

13 10

9

1

1. Speaker

2. Volume control

3. On/Off button

4. Favourite button

5. DAB/FM button

2 3 4 5 6

6. Auto Tune button

7. Info button

8. Preset button

9. Tuning / Select control

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

7 8

10. Auxiliary input socket

11. LCD display

12. Charge / Low battery indicator

13. Headphone socket

2

Controls

(Rear)

15

16

14. Telescopic aerial

15. Line output socket

16. DC input socket

17. Battery compartment screw

3

14

17

Battery operation using alkaline batteries

(also see page 23)

1. Ensure your radio is disconnected from the mains supply and the aerial is fully retracted.

screwdriver to loosen the screw securing the battery cover.

3. Slide the switch inside the battery compartment to the Alkaline position.

4. Insert four LR14 (C size) Alkaline batteries into the spaces in the compartment. Take care to ensure all batteries are inserted with the correct polarity as shown inside the battery compartment.

5. Close the battery cover and gently tighten the screw using a fl at bladed screwdriver. Do not overtighten.

• Important: when using Alkaline batteries the battery switch must be placed in the Alkaline position. Failure to do so could result in serious damage to the batteries or radio.

• When the batteries are exhausted, the charge/low battery indicator will show red for a short while.

The radio will then switch itself off. It may not be possible to switch the radio back on until the batteries are replaced, or until the radio is connected to the mains adaptor.

• If the radio is not to be used for any extended period of time it is recommended that the batteries are removed from the radio.

• We would recommend for economy that the Vintage is used via the

AC adaptor whenever possible with battery operation for occasional use only. If extended listening using batteries is anticipated, then the use of rechargeable batteries is recommended.

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

2

3

4

Battery operation using rechargeable batteries

(also see page 23)

The fi rst few times that you charge a new set of batteries, you may fi nd that the charge and play times are very short. Normal operation should be achieved after 3 or 4 charge - discharge cycles.

Batteries are only charged while the radio is connected to the mains supply via its adaptor and it is switched off using the On/Off button.

1. Ensure your radio is disconnected from the mains supply and the aerial is fully retracted.

screwdriver to loosen the screw securing the battery cover.

3. Slide the switch inside the battery compartment to the NiMH position.

4. Insert four Rechargeable LR14 (C size) batteries into the spaces in the compartment. Take care to ensure all batteries are inserted with the correct polarity as shown inside the battery compartment. The radio is designed to be used with Nickel Metal Hydride (NiMH) rechargeable batteries.

5. Close the battery cover and gently tighten the screw using a fl at bladed screwdriver. Do not overtighten.

6. Plug the mains adaptor into your radio and then plug the adaptor into the mains.

7. The Charge light will fl ash green indicating that the batteries are charging. Batteries will be fully charged in around 3 - 7 hours depending on their capacity. The charge light shows a steady green light when the battery charging is complete.

• Important: when using rechargeable batteries the battery switch must be placed in the NiMH position. Batteries will only be charged when the radio is switched off and connected to the AC adaptor.

2

3

5

Battery operation using rechargeable batteries cont.

• When the batteries are exhausted, the charge/low battery indicator light will show red for a short while. The radio will then switch itself off.

It may not be possible to switch the radio back on until the batteries are recharged, or until the radio is connected to the mains adaptor.

IMPORTANT: The batteries should not be exposed to excessive heat such as sunshine, fi re or the like. After use, disposable batteries should if possible be taken to a suitable recycling centre. On no account should batteries be disposed of by incineration.

• If the radio is not to be used for any extended period of time it is recommended that the batteries are removed from the radio.

Using the AC adaptor

1. Insert the adaptor plug into the DC in socket on the rear of your radio.

2. Plug the adaptor into a standard 13A mains socket outlet. Whenever the adaptor is plugged in to the radio and switched on at the mains the batteries are automatically disconnected. If the adaptor is plugged in to the radio but not switched on then the radio will run from the batteries if fi tted.

The AC adaptor should be disconnected from the mains supply and the radio when not in use.

the radio to the mains supply. The mains socket used for the radio must remain accessible during normal use. In order to disconnect the radio from the mains completely, the mains adaptor should be removed from the mains socket outlet

completely.

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

6

Operating your radio - DAB

1. Carefully extend the telescopic aerial.

'Welcome to DAB'.

3. If this is the fi rst time the radio is used a quick scan of the Band III

DAB channels will be carried out. If the radio has been used before the last used station will be selected.

4. During the scanning process, the lower line of the display shows a bar-graph indicating progress of the scan.

5. When the scanning is completed the fi rst station (in numeric-alpha order 0...9...A....Z) will be selected.

6. If the station list is still empty after the scan your radio will display

'Service not available'.

7. If no signals are found it may be necessary to relocate your radio to a position giving better reception. Then, either switch your radio off and on again, or press the Auto Tune button to repeat the scan.

2

7

Selecting a station - DAB

1. The top line of the display shows the name of the station currently selected.

2. Rotate the Tuning control to scroll through the list of available stations on the lower line of the display. Stop rotating the Tuning control when you fi nd the station that you wish to hear.

3. Press and release the Tuning control to select the station. The display may show 'Now Tuning...' while your radio fi nds the new station.

Note: If after selecting a station the display shows 'Service not available' it may be necessary to relocate your radio to a position giving better reception.

The use of radio station presets for selecting your preferred radio stations is described on page 17.

2,3

4

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

8

Display modes - DAB

Your radio has a range of display modes:-

1. Press and release the Info button to cycle through the various modes.

a. Scrolling text b. Program Type

Displays scrolling text messages such as artist/track name, phone in number etc.

Displays the type of station being listened to e.g. Pop, Classic, News etc.

c. Multiplex Name d. Time and date e. Frequency f. Bit rate & audio type g. Signal

Displays the name of the DAB multiplex to which the current station belongs.

Displays the current time and date.

Displays the frequency of the DAB multiplex for the station listened to.

Displays the digital bit rate & audio type for the station being listened to.

Displays a graph showing the signal strength for the station being received.

The clear unfi lled rectangle indicates minimum signal level required for

9

1 a b c d e f g

Finding new radio stations - DAB

As time passes new stations may become available. To fi nd new stations proceed as follows:-

1. Press and release the Auto Tune button. The display will show

'Scanning...' and your radio will perform a scan of the Band III DAB channels. As new radio stations are found the station counter on the right-hand side of the display will increase and the radio stations will be added to the list stored in the radio.

Secondary services - DAB

1. Certain radio stations have one or more secondary services associated with them. If a radio station has a secondary service associated with it the display will show '>>' next to the station name on the station list.

The secondary service will then appear immediately after the primary service as you rotate the tuning control clockwise.

2. Press and release the Tuning control to select the station.

3. When the secondary service shuts down, your radio will automatically switch back to the main radio station (or primary service) if it is available.

1

1,2

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

10

Manual Tuning - DAB

Manual tuning allows you to tune directly to the various DAB Band III channels. UK DAB stations are currently located in the range 11B to

12D.

1. Press and hold in the Info button until the display shows 'Manual

Tune'. Press and release the Tuning control to select this function.

3. Press and release the Tuning control. The open block in the signal strength graph shows you the minimum signal strength needed for good DAB reception. The signal blocks will go up and down showing the changing signal strength as you adjust the telescopic aerial or the radio position. Any new radio stations found on the tuned DAB multiplex will be added to the list stored in the radio.

4. Press and release the Tuning control to return to the normal tuning mode.

Signal strength display - DAB

1. Repeatedly press and release the Info button until the lower line of the display shows signal strength.

2. Position your radio and try adjusting the aerial so as to give maximum number of black rectangles on the signal strength display. Normally, the best reception will be found with the aerial fully extended.

3. The clear unfi lled rectangle indicates minimum signal level required for satisfactory reception.

11

1

1-4

1

Dynamic Range Control settings - DAB

Dynamic Range Control (also known as DRC) can make quieter sounds easier to hear when your radio is used in a noisy environment.

2. Press and hold in the Info button. The display will show 'Manual Tune'.

4. Press and release the Tuning control to enter the adjustment mode.

5. Rotate the Tuning control to select the required DRC setting (the default is 0).

DRC 0 - DRC is switched off, Broadcast DRC will be ignored.

DRC 1/2 - DRC level is set to 1/2 that sent by broadcaster.

DRC 1 - DRC level is set as sent by broadcaster.

6. Press and release the Tuning control to confi rm the setting. The display will return to normal tuning mode.

Note: Not all DAB broadcasts are able to use the DRC function. If the broadcast does not support DRC, then the DRC setting in the radio will have no effect.

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

3-6

1

2

12

Operating your radio - Search tuning - FM

1. Carefully extend the telescopic aerial fully.

2

4. Press and immediately release the Auto Tune button, your radio will scan in an upwards direction (low frequency to high frequency) and stop automatically when it fi nds a station of suffi cient strength.

5. After a few seconds the display will update. The display will show the frequency of the signal found. If the signal is strong enough and there is RDS data present then the radio will display the station name.

3

4-7 before.

7. To scan the FM band in a downwards direction (high frequency to low frequency) press and hold down the Auto Tune button for 2 seconds and then release.

8. When the waveband end is reached your radio will recommence tuning from the opposite waveband end.

9

The use of radio station presets for selecting your preferred radio stations is described on page 17.

If you fi nd that an FM broadcast has a lot of background hiss, this may often be reduced by setting the radio into Mono reception mode for the current FM station. Please refer to the section 'Stereo / Mono setting - FM' on page 18 for further details.

13

Manual tuning - FM

telescopic aerial fully for FM reception.

control the frequency will change up or down by 50 kHz.

4. When the waveband end is reached the radio will recommence tuning from the opposite waveband end.

6. To switch off your radio press the On/Off button.

If you fi nd that an FM broadcast has a lot of background hiss, this may often be reduced by setting the radio into Mono reception mode for the current FM station. Please refer to the section 'Stereo / Mono setting - FM' on page 18 for further details.

1,6

2

3

5

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

14

Display modes - FM

The Radio Data System (RDS) is a system in which inaudible digital information is transmitted in addition to the normal FM radio programme.

RDS offers several useful features. In FM mode the bottom line of the display can be set to any of the following display options:-

1. Press and release the Info button to cycle through each of the options.

a. Scrolling text Displays scrolling text messages such as artist/track name, phone in number

etc.

b. Program type c. Time and date

Displays type of station being listened to e.g. Pop, Classic, News, etc.

Displays the current time and date.

d. Frequency Displays frequency of the station being e. Audio mode Display shows Auto (stereo) or Mono.

Note: Your radio will display 'No Radio Text' on the lower line of the display if there is no scrolling text available and 'No PTY' if there is no programme type information.

15

1 a b c d e

Favourite button

Your radio is fi tted with a button which when pressed will automatically select the required waveband and tune to your Favourite radio station.

With this button you can store one favourite station from either the DAB or FM wavebands.

To set up your favourite station, follow these steps:

1. Carefully extend the telescopic aerial and switch on your radio.

2. Select the desired waveband (DAB or FM) and tune into the required radio station as described on the preceding pages.

3. Press and hold down the Favourite button (for 5 seconds) until the display shows 'My Fav. saved'.

Recalling your favourite station

1. Carefully extend the telescopic aerial and switch on your radio.

If your radio is in Auxiliary Input mode, press and release the DAB/FM button to select normal radio operation.

2. Momentarily press the Favourite button, your radio will automatically select the DAB or FM waveband as needed and then tune to the radio station stored in the favourite memory.

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

3

2

16

Preset stations - DAB and FM

To make it easier for you to tune your radio to the stations that you prefer, you may store selected radio stations as presets. Your radio holds presets separately for DAB and FM radio modes.

You may set as many or as few presets as you like in each mode.

You can easily switch between displaying all DAB stations (or all FM frequencies) and displaying only those that you have set as presets.

Any station or frequency which has been marked as a preset can easily have the mark cancelled should your preferences or needs change.

Presets are retained when your radio is switched off.

1. To setup your preset stations, tune into the required station.

2. Press and hold down the Preset button until the displays shows a tick symbol next to the radio station name or frequency. This indicates that the radio station is marked as a preset. To cancel the preset mark, press and hold the Preset button again.

3. Repeat steps 1 and 2 as needed for any other stations that you want as presets.

4. To view only the preset stations for the currently selected waveband when tuning, press and release the Preset button so that the heart symbol shows in the display.

5. To listen to one of the preset radio stations, rotate the Tuning control until the required radio station is displayed. Press and release the

Tuning control to select and tune to that station.

6. To cancel the preset stations view, press and release the Preset button so that the heart symbol disappears from the display. Your radio will then be able to access the full station list using the Tuning control.

17

2,4

6

5

Stereo / Mono setting - FM (headphones only)

Your radio will play stereo FM broadcasts in stereo provided that the received signal is of adequate strength. However, as a stereo signal becomes weaker the audio signal will become poorer. It may be preferable to force the radio to play the station in mono in order to reduce the level of background hiss.

2. Tune to the required FM radio station as previously described (see pages 13, 14).

3. Press and release the Tuning control so that the display shows 'Switch

to Mono'. The radio will play the current station in mono.

The Mono override is a temporary setting and is applied to the currently tuned station only. It is cancelled automatically by tuning to another station.

4. If you wish to cancel the Mono override while listening to the currently tuned radio station, press and release the Tuning so that the display shows 'Switch to Auto'. The radio will play the current station in stereo if the signal is suffi ciently strong.

1

3-4

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

18

Scan sensitivity setting - FM

Your radio will normally scan for FM broadcasts which are strong enough to give good reception. However, you may wish the Auto-scan function to also be able to fi nd weaker signals, possibly from more distant radio transmitters. Your radio includes a local / distant option for the Auto-scan function.

2. If needed, press the DAB/FM button to select the FM band.

3. Press and hold the Info button until the display shows 'FM Scan Zone' then press the Tuning control to enter the scan zone selection menu. on the lower line of the display. The Distant option will allow the radio to fi nd weaker signals when scanning.

The currently stored setting will be shown with an asterisk on the display.

5. Press and release the Tuning control to confi rm your selection. The radio will then revert to the normal information display. The Local or

Distant setting is stored in the radio and remains in force until changed or until a System Reset.

Note: The initial setting (out of the box, or after a System Reset) causes the radio to ignore weaker (or more distant) signals.

19

3-5

1

2

3

Software version

The software display cannot be altered and is just for your reference.

1. To view the software version on the display, ensure your radio is in

DAB mode and press and hold the Info button for 2 seconds.

the Tuning control the software version will appear on the display.

1

2

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

20

System reset

If your radio fails to operate correctly, or some digits on the display are missing or incomplete, it may be possible to restore normal operation by carrying out a System Reset operation on your radio. This will restore the radio's settings to their factory defaults. No presets will be stored, and the list of DAB radio stations will be empty.

If you have moved to a different part of the country and you wish to erase local DAB radio stations that are no longer available from the stored list, then you may carry out this procedure. Your radio will automatically re-scan for the DAB stations available at your current location when it restarts.

1. Ensure your radio is in DAB or FM mode. Press and hold down the

Info button for 2 seconds.

press and release the Tuning control.

3. If you wish to perform the reset operation, press and release the Tuning control one more time. A full reset of your radio will be performed. All presets and station lists will be erased.

4. After a system reset a scan of the DAB band will be performed.

In case of malfunction due to electrostatic discharge, reset the product

(temporary disconnection of the power adaptor and removal of batteries may be required) to resume normal operation.

If a problem persists our technical staff would be pleased to offer any assistance on operating the radio. Our technical helpline number is 020 8758 0338.

21

1

2-3

Headphone socket

A 3.5mm Headphone Socket located on the top of your radio is provided for use with either headphones or an earpiece. Inserting a plug automatically mutes the internal loudspeaker.

Please be aware that sensitivity of headphones can vary widely. We therefore recommend setting volume to a low level before connecting headphones in the radio.

IMPORTANT: Excessive sound pressure from earphones and headphones can cause hearing loss.

Auxiliary input socket

1. Connect a stereo or mono audio source (i.e. CD player, MP3 player, etc.) to the Auxiliary input socket.

DAB/FM button until the display shows 'AUX IN'.

Note that the Auxiliary Input mode can only be selected when a plug is inserted in the socket.

3. Adjust the Volume control on your player and on the radio for comfortable listening.

4. Remove the cable from the Auxiliary input socket or press and release the DAB/FM button to cancel Auxiliary Input mode.

Line out socket (3.5mm Jack)

A 3.5mm Line Out socket located on the rear of your radio is provided for connecting the audio signal to an external amplifi er. Inserting an audio cable into this socket will not mute the internal loudspeaker. Set the volume control on the radio to minimum if desired.

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

2

1

22

A Few Words about Batteries… Rechargeable batteries

Your Roberts Vintage radio has been designed to use a choice of power sources. You may plug it into the mains using the supplied high-effi ciency adaptor, or for listening away from the mains you may use either alkaline or rechargeable batteries. We do not recommend the use of carbon-zinc or zinc-chloride batteries.

Your Vintage radio uses a range of methods to ensure correct and safe charging of Rechargeable Nickel-Metal-Hydride batteries. These work to protect your batteries from excessive charge and discharge. These protections can only work properly if the advice above is followed. In particular, the radio will not be able to correctly charge batteries if they are a mixture of different brands, or different ages, or different capacities.

It is very important that you read the advice and warnings given below.

1) Whichever type of batteries you choose to use, it is very important that the battery selection switch under the cover is set to the correct type. a. If no batteries are fi tted, then set the switch to the Alkaline position.

This position minimises the power consumption when the radio is powered from the mains.

b. If Alkaline batteries are fi tted, then set the switch to the Alkaline position. c. If Rechargeable batteries are fi tted, then set the switch to the

NiMH position. Your radio is designed to use Nickel-Metal-Hydride rechargeable batteries. No other type of rechargeable battery should be used in the radio.

We recommend that all the rechargeable batteries used in your radio are bought together as a set. They should always be charged together and discharged together and not “borrowed” from time to time for other applications. This will ensure that they give their optimum performance in your radio.

We recommend that the rechargeable batteries that you use should be from a quality brand, and should be of at least 2500mAh capacity.

Batteries of this capacity should power your radio for between 15 and

20 hours depending upon the volume of the radio, whether DAB or FM mode is used (DAB mode uses slightly less power than FM), and also depending on the condition of the batteries. Higher capacity batteries are available and will give longer life, but will generally be more expensive.

2) NEVER mix old and new Alkaline batteries. The old batteries may suffer damage and leak which will damage your radio and whatever the radio is standing on.

3) NEVER mix old and new Rechargeable batteries. This may result in unreliable charging and shortened battery life. Never mix

Rechargeable batteries of different types or capacities even if they are new.

4) NEVER mix Alkaline and Rechargeable batteries. The recharging of

Alkaline batteries can be very dangerous.

Before you fi rst install a new set of rechargeable batteries into your radio you should fi rst make sure that the battery type switch beneath the battery cover is in the NiMH position. Install the batteries arranging them as shown inside the battery compartment. Plug the mains adaptor into the radio and then into the mains socket. While the batteries are charging the charge indicator should show a fl ashing green light. When the batteries are fully charged the indicator will stop fl ashing and will show a steady green light. The time taken to charge the batteries will depend on how much charging they require. New batteries may be partly charged when fi rst fi tted, but it is normal for a set of batteries to take several hours to charge fully (this can be between 3 and 7 hours depending on the battery capacity and their initial state of charge).

23

If you use the radio powered from the batteries, the charge/low battery indicator light will be off until the batteries are exhausted. The charge/ low battery indicator light will then show red for a short while before the radio switches itself off. It does this in order that the batteries are not excessively discharged. This would otherwise damage the batteries and shorten their life.

If you use the radio powered from the mains with rechargeable batteries fi tted, the charging process is suspended until you switch off the radio.

When you switch off the radio using its On/Off button charging will then resume. If the batteries have already been charged then they will only charge for a few more minutes before the charge indicator stops fl ashing.

Improper use of batteries may result in leakage of fl uid, overheating or explosion. Battery fl uid is corrosive and may also be toxic. Battery fl uid can cause skin burns, can damage the eyes, and can be harmful if swallowed.

If you only listen to your radio for short periods, you do not need to connect your radio to the mains to charge the batteries every time that you use it. However, if the radio is not to be used for a few weeks, then we recommend that the batteries are fully charged (charge light shows steady green) before the radio is put to one side.

If you intend not to use your radio for some months, then we recommend that the batteries are removed and put away, keeping them in a cool place out of reach of children, away from moisture and such that no metal object can contact the battery terminals.

With care, rechargeable batteries can last a long time and can operate for many hundreds of charge and discharge cycles. When your rechargeable batteries can no longer power your radio adequately, please dispose of them responsibly using a local battery recycling facility.

To avoid danger and risk of injury, please follow these guide lines

1. Keep batteries out of the reach of children.

2. Do not heat, open, puncture, mutilate or dispose of batteries by burning.

3. Do not mix different battery types or old and new batteries. Always replace all the batteries at the same time.

4. Do not carry or store batteries such that metal objects may contact the end caps.

5. Remove batteries from the radio if they are worn out or if you are storing it for a long time.

6. Remove old or worn out batteries promptly, and recycle or dispose of them according to the regulations applicable to your location.

7. If a battery does leak, remove all batteries from the product, taking care to avoid directly touching the leaked fl uid. If the fl uid contacts skin or clothes wash with water immediately. Before inserting new batteries, thoroughly clean the battery compartment with a damp paper towel, or follow the battery manufacturer’s advice for clean up.

If you need any further advice, please call our Technical Helpline on :-

020 8758 0338 (Mon-Fri)

24

Display backlight

1. When using the radio powered from batteries, the display backlight will be switched on for approximately 12 seconds when any button is pressed.

2. When your radio is powered by the AC mains using the supplied mains adaptor the display backlight will always be on whenever the radio is switched on.

USB socket for software upgrade

As software updates become available information on how to upgrade your radio may be found at www.robertsradio.co.uk

25

General

Do not allow this radio to be exposed to water, steam or sand. Do not leave your radio where excessive heat could cause damage such as in a parked car where the heat from the sun can build up even though the outside temperature may not seem too high. It is recommended that the DAB band be used wherever possible as better results in terms of quality and freedom from interference will usually be obtained than on the FM band.

The name plate is located on the underside of your radio.

• Your radio should not be exposed to dripping or splashing and that no objects fi lled with liquids, such as vases, shall be placed on the radio.

• It is recommended to operate the product such that there is a minimum distance (10cm recommended) to adjacent objects in order to ensure good ventilation.

• The ventilation of the product should not be restricted by covering it or its ventilation openings with items such as newspapers, tablecloths, curtains etc.

the product.

• It is recommended to avoid using or storing the product at extremes of temperature. Avoid leaving the unit in cars, on window sills, in direct sunlight etc.

Specifi cations

Power Requirements

Mains

Batteries

Battery Life

AC 100 240V 50/60Hz (adaptor)

4 x LR14 (C size)

Up to 80 hours of listening for 4 hours a day at normal volume using alkaline cells.

Up to 20 hours - 2500 mAh NiMH

Frequency Coverage

DAB

Circuit Features

Loudspeaker

Output Power

Headphone socket

Auxiliary Input socket

Line output socket

1 x 117 x 42mm

1.0 Watt

3.5mm dia.

3.5mm dia.

3.5mm dia.

Aerial System FM Telescopic aerial

174.928 - 239.200MHz

The Company reserves the right to amend the specifi cation without notice.

26

Guarantee

This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free of charge.

The guarantee does not cover:

1. Damage resulting from incorrect use.

3. Receivers with removed or defaced serial numbers.

N.B. Damaged or broken telescopic aerials will not be replaced under guarantee.

Procedure:

Any claim under this guarantee should be made through the dealer from whom the instrument was purchased. It is likely that your Roberts' dealer will be able to attend to any defect quickly and effi ciently, but should it be necessary the dealer will return the instrument to the company’s service department for attention. In the event that it is not possible to return the instrument to the Roberts' dealer from whom it was purchased, please contact

Roberts Radio Technical Services at the address shown below.

These statements do not affect the statutory rights of a consumer.

ROBERTS RADIO TECHNICAL SERVICES

97-99 Worton Road

Isleworth Middlesex

TW7 6EG

Technical Helpline :- 020 8758 0338 (Mon-Fri during offi ce hours)

Website: http://www.robertsradio.co.uk

© 2011 Roberts Radio Limited

Issue 1