MOON Evolution Series 870A audio amplifier Owner's Manual
The MOON Evolution Series 870A is a powerful Dual-Mono power amplifier designed to deliver exceptional audio performance. With its fully balanced differential circuitry, custom toroidal transformers, and oversized power supply, this amplifier provides incredible power and clarity, making it ideal for demanding audiophiles. The 870A comes with multiple input options, including both balanced and unbalanced inputs, and allows for bridged-mono operation for even more powerful sound.
Advertisement
Advertisement
Owner’s Manual
Evolution Series
870A
Reference Dual-Mono Power Amplifier
870A Reference Dual-Mono Power Amplifier
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or another apparatus that produces heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for safety. If the provided plug does not fit into the outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Unplug mains cord during transportation.
11.
Only use attachments and accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power cord or plug has been damaged; liquid has been spilled or objects have fallen into the apparatus; or the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. No naked flame sources, such as candles, should be placed on the apparatus.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
____________________________________________________________________________________
870A Reference Dual-Mono Power Amplifier
Important Safety Instructions (cont’d)
The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Marking by the “CE” symbol (shown left) indicates compliance of this device with the
EMC (Electromagnetic Compatibility) and LVD (Low Voltage Directive) standards of the
European Community
Please read all instructions and precautions carefully and completely before operating your Simaudio MOON 870A Dual-Mono Power Amplifier.
1.
ALWAYS
disconnect your entire system from the AC mains before connecting or disconnecting any cables, or when cleaning any component. To completely disconnect this apparatus from the AC mains, disconnect the power suppy cord plug from the AC receptacle.
2.
The MOON 870A must be terminated with a three-conductor AC mains power cord which includes a protective earthing connection. To prevent shock hazard, all three connections must
ALWAYS
be used.
Connect the MOON 870A only to an AC source of the proper voltage; Both the shipping box and rear panel serial number label will indicate the correct voltage. Use of any other voltage will likely damage the unit and void the warranty
3.
AC extension cords are
NOT
recommended for use with this product. The mains plug of the power supply cord shall remain readily accessible.
4.
NEVER
use flammable or combustible chemicals for cleaning audio components.
5.
NEVER
operate the MOON 870A with any covers removed. There are no user-serviceable parts inside. An open unit, especially if it is still connected to an AC source, presents a potentially lethal shock hazard. Refer all questions to authorized service personnel only.
6.
NEVER
wet the inside of the MOON 870A with any liquid. If a liquid substance does enter your MOON
870A, immediately disconnect it from the AC mains & take it to your MOON dealer for a complete check-up.
7.
NEVER
expose the MOON 870A to dripping or splashing of liquids and no objects filled with liquids, such as vases, shall be placed on top.
8.
NEVER
block air flow through ventilation slots or heatsinks.
9.
NEVER
bypass any fuse.
10.
NEVER
replace any fuse with a value or type other than those specified
11.
NEVER
attempt to repair the MOON 870A. If a problem occurs contact your MOON dealer.
12.
NEVER
expose the MOON 870A to extremely high or low temperatures.
13.
NEVER
operate the MOON 870A in an explosive atmosphere.
14.
ALWAYS
keep electrical equipment out of reach of children.
15.
ALWAYS
unplug sensitive electronic equipment during lightning storms.
16.
WARNING:
Do not expose batteries or battery pack to excessive heat such as sunshine, or fire or the like.
____________________________________________________________________________________
870A Reference Dual-Mono Power Amplifier
Table of Contents
Introduction ..................................................... 6
Unpacking........................................................ 7
Installation & Placement ................................... 7
Rear Panel Layout ............................................ 8
Connecting the 870A ......................................... 9
Balanced Operation ........................................... 9
Bridged-Mono Operation .................................. 10
Operating the 870A ......................................... 11
Troubleshooting ............................................ 11
Remote Operation ..........................................12
Specifications ................................................ 13
www.simaudio.com
Simaudio Ltd., 1345 Newton Road
Boucherville, Quebec J4B 5H2 CANADA
Date Code: 20140909
____________________________________________________________________________________
870A Reference Dual-Mono Power Amplifier
Introduction
Thank you for selecting the
MOON 870A
Dual-
Mono power amplifier as a part of your hi-fi reproduction system. This power amplifier has been designed to offer state-of-the-art high-end performance in an elegant package, while retaining all the sonic hallmarks on which Simaudio has made its reputation. We have spared no effort to ensure hours of listening. This is the result of a “break-in” period required for the numerous high quality electronic parts used throughout this amplifier.
Before setting up your new
MOON 870A
, we encourage you to please read this manual thoroughly to properly acquaint yourself with its that it is among the finest two-channel amplifiers available. We have been building high-performance audio equipment for over 30 years, and the know-how gained through our cumulative experience is an important reason why amplifiers are so musically satisfying.
MOON
features. We hope you enjoy listening to the
MOON 870A
Dual-Mono power amplifier as much as the pride we have taken in creating this fine audio product. We understand the power and emotion of music and build our products with the goal of faithfully capturing these elusive qualities.
Your new amplifier is a true Dual-mono design, whereby each channel operates completely independent of the other. The chassis, power cord and power switch are the only parts of this amplifier that both channels share. The performance of your
870A
will continue to improve during the first 300
The information contained in this manual is subject to change without notice. The most current version of this manual is available on our official website at http://www.simaudio.com
Your
MOON 870A
Dual-Mono Power Amplifier incorporates many significant design features to achieve its
“world-class” level of performance. This is an abbreviated list of the more important features:
Proprietary
“Lynx”
Technology which eliminates feedback. The results are: Real-time amplification is achieved since interactions from the speaker back to the amplifier are virtually eliminated; More accurate musical reproduction with respect to tonality; Virtually non-existent transient intermodulation distortion (which is far more degrading to sonic performance than harmonic distortion); The elimination of common phase errors resulting from feedback.
A custom
proprietary toroidal transformer design
with lower magnetic, electrical and thermal loss, yielding an improved power transfer and lower regulation factor, resulting in increased current speed and better dynamics.
Fully
balanced differential
circuitry up to the output stage.
Output stable
to any known speaker impedance.
Class A output
to 5 watts for greater efficiency.
RS-232 port
for i) full unsolicited bidirectional feedback in custom installation setups and ii) firmware updates.
An
oversized
power supply.
An
exceptionally short signal path
for a faster transient response.
Precision matched and fully decoupled
proprietary
MOON Bipolar Output transistors
with unprecedented gain linearity resulting in improved bass response and even more accurate sonic reproduction.
A
high damping factor
which yields superior musical dynamics, improved signal speed and refined timbre accuracy.
Ultra rigid chassis construction
to minimize the effects of external vibrations.
Designed to be
powered up at all times
for optimal performance.
____________________________________________________________________________________
6
870A Reference Dual-Mono Power Amplifier
Unpacking
The
MOON 870A
power amplifier should be removed from its box with care.
The following accessories should be included inside the box with your amplifier:
9 AC power cable
9
This owner’s manual
9
Warranty and product registration information (USA and Canada only)
Once the
870A
is unpacked, inspect it thoroughly and report any damage to your dealer immediately.
We suggest that you keep all of the original packaging, storing it in a safe, dry place in case you’re required to transport this product. The customized packaging is specially designed to protect the
870A
from any potential damage during transit.
Please write the serial number of your new
MOON 870A
in the space provided below for future reference.
Serial No.
: ________________
Installation & Placement
The
MOON 870A
Dual-Mono power amplifier is both powerful and heavy. It requires reasonable ventilation to maintain an optimum and consistent operating temperature, especially since it will radiate heat when driven hard. Consequently, it should be placed in a location with empty space around it for proper heat dissipation. You should never place another component on top of this amplifier. As well, the amplifier should be placed on a solid level surface. You should avoid placing it near a heat source or inside a closed cabinet that is not well ventilated as this could compromise the amplifier’s performance and reliability. The
870A
uses two large toroidal transformers in its power supply; even though they are well shielded, you should not place this amplifier too close to source components sensitive to EMI, such as turntables, phono preamplifiers and CD Players.
If the surface you have chosen isn’t perfectly level, each of the four (4) cones of your
870A
are height adjustable; carefully using your fingers, you can either raise each leg by turning the cone underneath clockwise, or lower each leg by turning it counterclockwise.
We strongly recommend that you leave these cones mounted to the component at all times for reasons related to both performance and aesthetics.
____________________________________________________________________________________
7
870A Reference Dual-Mono Power Amplifier
Rear Panel Layout
Figure 1: Rear panel of Moon 870A Dual-Mono Amplifier
The rear panel will look similar to Figure 1 (above).
Each channel has one balanced (differential) input on an XLR connector and one unbalanced (singleended) input on a RCA connector. There is no switch to toggle from balanced mode to singleended mode. You may operate the amplifier in either mode, but only one mode at one time for each channel. When you’re using the balanced XLR inputs,
you must first remove the factory installed “dummy” XLR jumpers
(see figure 2 below) from the back panel XLR connectors and store them in a safe place. These jumpers are required ONLY when using the single-ended RCA inputs. If you decide to switch to single-ended input mode, you must reinstall the XLR jumpers (between pins 1 and 3) exactly as show below:
Figure 2: XLR connector without and with jumper accessory
There are two pairs of heavy duty gold-plated speaker binding posts for each channel to accommodate bi-wiring. They are each labelled
“Speaker Output 1” and “Speaker Output 2”. two 12 Volt triggers, each on a 1/8” mini-jack; one input and one output, the latter for use in the event that wish you to “daisy chain” a second power amplifier on the same trigger circuit. The lower midsection has from left to right; the “AC Fuse” socket cover; the power “main switch”; and the “AC Input”
IEC receptacle for the power cord.
The upper mid-section has an RS-232 input on a
DB9 connector. To the right of this connector are
____________________________________________________________________________________
8
870A Reference Dual-Mono Power Amplifier
Connecting the 870A
Prior to making any connections or removing the
XLR jumpers, the power amplifier must be turned off and the AC cable disconnected for at least 1 minute.
1.
Connect the input cables running from your preamplifier’s outputs, whether balanced or single-ended, to the amplifier’ s XLR or RCA inputs, respectively. We highly recommend that you use the balanced XLR inputs (provided that your preamplifier has balanced outputs) to take full advantage of
870A
Power Amplifier’s capabilities. Please refer to the next section,
“Balanced Operation” on for further information.
2.
Connect your speakers, with the cables of your choice, to the
870A
’s speaker binding posts.
Take care to respect the polarity (“+” , “-” ) of the outputs. Once again, don’t hesitate to use high quality speaker cables
*
. Poor quality speaker cables can degrade the overall sonic performance of your system.
Do not connect cables to both the XLR and
RCA inputs at the same time. Damage to both the 870A and the connected equipment can result that is not covered by warranty.
3.
Connect the supplied AC power cable to the IEC receptacle, located on the amplifier’s rear panel.
Ensure that the AC wall outlet you use has a functioning ground. For the best sonic performance, it is preferable that you plug your
870A
directly into a dedicated AC outlet and avoid using an extension cord. If you have the time and willingness, consider installing a superior quality AC wall outlet such as a hospital grade Hubbell
*
.
Don’t hesitate to use high quality interconnect cables
*
. Poor quality interconnect cables can degrade the overall sonic performance of your system. It is recommended, though not mandatory, to use balanced interconnects between your preamplifier and the
870A
when using long cable runs (i.e. more than 3 meters in length).
Balanced Operation
When using an unbalanced interconnect, the audio signal runs through both the center wire and the shield/ground wire. Any noise picked up by this interconnect (ie. nearby magnetic fields such as an
AC power cord) will be reproduced by the amplifier and heard through the loudspeakers. Conversely, a balanced interconnect has three separate conductors; one for the ground and two for the actual signal. These two signals are identical except that one is 180 degrees out of phase with the other.
*
Please speak with your MOON Authorized Retailer about the benefits of high quality cables for your system, and superior quality AC wall outlet.
For example, when one conductor is carrying a signal of +5 Volts, the other will be carrying a signal of –5 Volts. When these two inverted signals on a balanced line are input into a differential power amplifier such as the
MOON 870A
, any noise picked up by the interconnect will be eliminated since a differential circuit amplifies only the difference between these two signals: Noise on a balanced interconnect will be equal on both conductors and therefore cancel out.
____________________________________________________________________________________
9
870A Reference Dual-Mono Power Amplifier
Bridged-Mono Operation
Figure 3: Bridged-Mono operation of the MOON 870A Dual-Mono Amplifier
If wish to operate the
MOON 870A
Dual-Mono
Power Amplifier as a monoblock amplifier, it can be converted to bridged mode without any complex modifications. Only a Simaudio XLR-BRIDGE Y-cable is required. This custom cable will allow one input signal to be sent to both channels of the amplifier’s inputs, as pictured above in Figure 3. One lead from the “Y” adapter must plug into right channel input and the other lead must plug into left channel input.
As well, you must use the positive terminal of each output binding post (exactly as in figure 3) for the loudspeaker connection. If you are unsure about how to accomplish a bridged-mono mode of operation, don’t hesitate to contact your
Authorized MOON
The MOON
870A
dealer. produces 1200 watts of output power at 8 ohms for a single channel when operating in bridged-mono mode.
____________________________________________________________________________________
10
870A Reference Dual-Mono Power Amplifier
Operating the 870A
We recommend leaving your
870A
powered up at all times to maintain optimal performance. When you plan on being away for a few days, it may not be a bad idea to power off your amplifier. Please
Turning on your MOON 870A for the first time
Prior to turning the amplifier on for the first time, make sure that every cable is properly connected to avoid any problems. Then turn on your preamplifier connected to the
870A
. Flick the main rocker switch, located on the rear panel, labeled “POWER” to the ‘1’ (on) position. The blue LED on the front panel will blink for up to 10 seconds while it achieves standby mode. When it stops blinking and
On and Off Sequence
To avoid having any annoying noises (ie. “thumps” and “pops”) emanate from your speakers when powering your
870A
on or off, you should always
Troubleshooting
The blue LED located on the front panel also indicates the operational status of your
MOON
870A
Dual-Mono power amplifier. When the LED starts blinking on and off during use, the circuitry is either over-heating or has detected the presence of
DC in the input signal:
Your
MOON 870A
is a “smart” power amplifier equipped with a self-diagnostic system that will automatically shut itself down when it detects DC
(direct current) from any input. If your
870A
power amplifier turns itself off or will not power up, there may very well be DC present in one (or more) of the amplifier’s inputs coming from one (or more) of your preamplifier/processor’s outputs or connected source components. You must determine if there is any DC present. The best way to accomplish this is by first powering down the
870A
via the main power rocker switch, then physically removing all inputs to the
870A
leaving only the speakers connected. Attempt to power up your
870A
again: keep in mind that once fully “broken-in”, your
870A
requires several hours of operation before reaching optimal performance after powering it up again.
is not illuminated, your
870A
is in standby mode.
Next, briefly press the push button labeled
“Standby” located on the front panel. You will hear a very faint click sound confirming that everything is in order. The blue LED on the front panel will illuminate, indicating that the
870A
is now powered up and ready for use. power up your preamplifier prior to powering up your
870A.
As well, always power down your
870A
prior to powering down your preamplifier.
Left Channel DC protection ............ LED blinks 2 times
Right Channel DC protection .......... LED blinks 3 times
Left Channel Over-heating.............. LED blinks 4 times
Right Channel Over-heating ........... LED blinks 5 times
Unknown Problem ......................... LED blinks 6 times
A successful power up will indicate the presence of
DC coming from your preamplifier or one of your signal sources (ie. CD Player).
If your
870A
still doesn’t power up, turn off the main power switch and check the AC fuse. If the fuse appears OK, put it back in its socket and then try to power up again the usual way. If the fuse is blown, replace it with a fuse of the same rating, and repeat the above process. At this point, you should be able to power up your
870A
. If not, immediately consult your dealer for assistance.
____________________________________________________________________________________
11
870A Reference Dual-Mono Power Amplifier
Remote Operation
Figure 4: Remote Operation with 12V Trigger
In figure 4 we have a
740P
Preamplifier and
870A
amplifier connected together via their respective 12V triggers; The 12V trigger output on the
740P
is connected to the 12V trigger input on the
870A
(using a 1/8” mini-jack cable). When you turn on the
740P
870A
via remote control (or its Standby button), the
will turn on automatically. The same rule applies when you put the
740P
into Standby mode.
____________________________________________________________________________________
12
870A Reference Dual-Mono Power Amplifier
Specifications
Configuration ................................................ Dual Mono
Power Supply Transformers ............................ 2 x 1.3kVA
Power Supply Capacitance ............................. 240,000µF
Class Of Operation ........................................ A/AB
Design ........................................................... Fully Balanced Differential to output stage
Input Impedance .......................................... 47,500 Ω
Input Sensitivity ............................................ 1400mV
Output Device Type ....................................... Bipolars - 16 per channel
Output Power at 8 Ω ...................................... 300 Watts per channel
Output Power at 4 Ω ..................................... 600 Watts per channel
Output Power – Bridged Mono at 8 Ω ............... 1200 Watts
Frequency Response ...................................... 10Hz - 200kHz +0/-3dB
Output Impedance ........................................ 0.01
Ω
Damping Factor (static) ................................ 800
Gain ............................................................. 31dB
Signal-to-noise Ratio ..................................... > 106dB @ full power
Maximum Output Voltage ............................... 58 Volts
Slew Rate ..................................................... 42V/µs
Maximum Current – Peak ............................... 72 amperes
Maximum Current – Continuous ...................... 30 amperes
Crosstalk @ 1kHz .......................................... -105dB
Intermodulation Distortion ............................. Unmeasureable
THD (20Hz - 20kHz @ 1 watt) ....................... < 0.015 %
THD (20Hz - 20kHz @ 300 watts) .................. < 0.04 %
Power Consumption @ idle ............................. 70 Watts
AC Power Requirements ................................. 120V / 60Hz or 240V / 50Hz
Shipping Weight ............................................ 98 lbs / 44 Kgs
Dimensions (W x H x D, inches) ..................... 18.75 x 7.5 x 17.5
Balanced Pin Assignment:
Pin 3 .......................... Negative
12 Volt Trigger: Logic........................... Direct (0V off, 12V on)
Input Impedance ......... 1k Ω
Current Consumption ... 12mA
NOTE:
If you require the RS-232 codes for your
870A
, please visit the "Contact Us" page and complete the "Information request" form on our website at www.simaudio.com.
Fuse Replacement: For the 120V version use a 10A fast blow (3AG size).
For the 230V version use a 5A fast blow (3AG size).
____________________________________________________________________________________
13

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Dual-mono design
- Proprietary 'Lynx' Technology
- Custom toroidal transformer
- Fully balanced differential circuitry
- Class A output to 5 Watts
- RS-232 port for firmware updates
- Oversized power supply
- High damping factor
- Ultra rigid chassis construction
- 12 Volt triggers for remote operation