advertisement
Infrared Turret Dome Camera
User Manual
Products: CD600 Series, CD601 Series, CD700 Series Cameras
Please read this manual before installing and using this camera and always follow instructions for proper use.
Save this manual for future reference.
CD600-CD601-CD700_CM
11/14/13
WARNING
Risk of electric shock – do not open .
To reduce the risk of electric shock, do not disassemble the camera module. No user serviceable parts are inside. Refer servicing to qualified service personnel.
!
WARNING
Do not use the camera if it is emitting fumes, smoke or a strange odor, or if it seems to function abnormally. Disconnect the power source immediately and consult your supplier.
CAUTION
Always follow the instructions in the installation guide when applying power. Fire and equipment damage can occur if power is applied incorrectly. For the correct power supply, refer to the specification sheet.
CAUTION
Do not install or operate in small, unventilated areas. Heat build up can significantly reduce the performance and operating life of the product and may cause a fire.
© 2013 Observint Technologies. All rights reserved.
11000 N. Mopac Expressway, Building 300, Austin, TX 78759
1.800.335.9777 | Fax: 1.866.267.9777
For Sales/Support, please contact your supplier. www.observint.com
WARNINGS & CAUTIONS
CAUTION
To prevent damage, do not drop the camera or subject it to strong shock or vibration.
CAUTION
If installed close to a TV, radio transmitter, magnet, electric motor transformer or audio speakers the magnetic field generated may interfere with or distort the image.
CAUTION
Never point it toward the sun. Use caution when operating the camera in the vicinity of spot lights or other bright lights and light reflecting objects.
CAUTION
Do not use the camera in extreme environments where high temperatures or high humidity exists. Use the camera only in environments where temperature is between -4 °F ~ 122 °F
(-20 °C ~ 50 °C) and humidity is below 85%.
Infrared Turret Camera User Manual iii
TABLE OF CONTENTS
Table of Contents
SECTION 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Camera components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Camera connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SECTION 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Tools you need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4 OSD Setup (CD700 series only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
SECTION 3 Aiming the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SECTION 4 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SECTION 5 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SECTION 6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 iv www.observint.com
SECTION 1: FEATURES
SECTION 1
Features
•
•
•
•
•
The CD600, CD601, and CD700 series cameras are weatherproof, vandal resistant turret dome cameras, ideal for outdoor or indoor locations where surveillance in low-light environments is required. These cameras include:
Advanced image sensors for greater picture clarity
Precision lenses to achieve the perfect view
(varifocal (VF) cameras have 2.8 - 12 mm adjustable zoom)
The ability to see in the dark with built-in IR array
Turret design for increased vandal resistance
Each model available with a black or white shell
Infrared Turret Camera User Manual 1
SECTION 1: FEATURES
1.1 Camera components
Drop Cable
Base
Bezel
Camera
Housing
Camera
Module
Zoom Adjust
(-VF Models)
Camera Lens
IR LEDs
Camera assembly
Video 75 Ohm
12 V dc
2 www.observint.com
1.2 Camera connections
Connect
SECTION 1: FEATURES
Connect
Single camera with monitor
Multiple camera system with DVR and monitor
Infrared Turret Camera User Manual 3
SECTION 2: INSTALLATION
SECTION 2
Installation
2.1 What’s in the box
•
•
•
The camera package contains:
Camera assembly
Instruction manual
Hardware kit, including four screws and four wall inserts
2.2 Tools you need
•
•
To install the camera, you will need:
Phillips #2 screwdriver
Small blade screwdriver (for adjusting VF model cameras)
•
•
•
Depending on how the camera is mounted, you may also need:
Hammer
Drill with 3/32" and 3/16" drill bits
3/4" hole saw
4 www.observint.com
SECTION 2: INSTALLATION
2.3 Installation instructions
1. Separate the base from the rest of the camera assembly by unscrewing the housing bezel.
Bezel
Remove the bezel
2. Determine where the camera will be mounted.
Infrared Turret Camera User Manual 5
SECTION 2: INSTALLATION
3. Using the base as a template, mark the location of the four mounting screw holes.
Mounting screw hole
Camera Base
4. Drill mounting screw holes into the mounting surface.
a. If the mounting surface is a soft material, such as a drywall, use a 3/16” bit to drill the mounting holes. Use a hammer to tap the wall inserts provided into each hole until they are flush with the surface.
OR (continue on next page)
6 www.observint.com
SECTION 2: INSTALLATION
5. Drill mounting screw holes into the mounting surface.
a. If the mounting surface is a soft material, such as a drywall, use a 3/16" bit to drill the mounting holes. Use a hammer to tap the wall inserts provided into each hole until they are flush with the surface.
OR b. If the mounting surface is a very soft material, such as ceiling tile, place a wood block behind the tile. Screws longer than 1" may be required. Drill holes for the mounting screws through the surface and into the wood block.
OR c. If mounting the camera on a harder surface, such as wood, drill the mounting screw holes with a 3/32" bit.
6. Determine the cable routing. If the cable is to be routed through a hole in the mounting location within the coverage of the base, perform the following steps. If the cable will be routed through a cable channel in the base, skip to step 9 .
Infrared Turret Camera User Manual 7
SECTION 2: INSTALLATION
Cable channel in base
7. Drill a 3/4" hole through the mounting surface at the center of the base.
3/4" Drop cable routing hole
Use a #2 Phillips screwdriver to mount the base with the provided screws.
8 www.observint.com
SECTION 2: INSTALLATION
8. With the camera in the camera housing, route the drop cable through the 3/4" hole until the camera housing is fitted onto the base. Place the housing bezel over the camera housing and screw it onto the base until the camera and camera housing are held in place. Skip to step 12.
9. Set the camera on the base with the camera cable pressed into one of the cable guides of the base. Allow some slack in the cable within the base to allow for camera positioning later.
10. Use a #2 Phillips screwdriver to mount the base with the provided screws.
11. Without allowing the camera to hang by the drop cable, place the camera module onto the base, cover with the camera housing, then move the bezel into place. Screw the housing bezel onto the base until the camera and camera housing are held in place.
Infrared Turret Camera User Manual 9
SECTION 2: INSTALLATION
10 www.observint.com
Reassemble camera
SECTION 2: INSTALLATION
12. Attach the BNC video/power cable to the camera cable as required.
CAUTION
Notice that power connectors on the BNC video/power cable are different at each end!
Connect
Cable attachment
To DVR/Monitor and Power
Infrared Turret Camera User Manual 11
SECTION 2: INSTALLATION
2.4 OSD Setup (CD700 series only)
CD700 series cameras include on-screen display (OSD) software for adjusting the internal camera settings to complement specific environment where it is installed.
These settings are adjusted using the OSD controller attached to the camera drop cable.
Joystick
The OSD controller includes a joystick that can be pushed down and rocked UP, DOWN, left (L) and right (R), or, to open the menu system and navigate the menus. OSD
Controller
To use the OSD controller, press the joy stick in (toward the controller block) to open the
OSD menu. (See the menu chart on the following page.) Rock the joystick UP or DOWN to highlight a parameter or submenu, then press the joystick in to select it. Rock the joystick right (R) to highlight an option, UP or DOWN to identify the option, then press the joystick in to select it. Repeat this method to navigate the menu system and select options.
12 www.observint.com
SECTION 2: INSTALLATION
OSD MENU OPTIONS
OSD SET
LENS
SHUTTER/
AGC
WHITE BAL
BACK
LIGHT
PICT
ADJUST
ATR
MANUAL
AUTO
AUTO
TYPE: DC / VIDEO
MODE: CLOSE / AUTO/OPEN SPEED: 0-255
HIGH LUMINANCE MODE: SHUT+AUTO IRIS / AUTO IRIS
BRIGHTNESS: 0-255
LOW LUMINANCE MODE: OFF / AGC
BRIGHTNESS: ×0 .25, ×0 .5, ×0 .75, ×1
MODE: SHUT+AGC
MAN-
UAL
SHUTTER: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000 s
AGC: 6, 12, 18, 24, 30, 36, 42, 44 .8
ATW SPEED / DELAY CNT / ATW FRAME / ENVIRONMENT
PUSH / ANTI CR / PUSH LOCK / USER1 / USER2 / MANUAL
OFF / BLC / HLC
MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN
OFF
ON
--
LUMINANCE/CONTRAST
Infrared Turret Camera User Manual 13
SECTION 2: INSTALLATION
OSD SET
(cont .)
MOTION
DET
OFF
ON
--
DETECT SENSE / BLOCK DISP / MONITOR AREA / AREA
SEL / TOP / BOTTOM /
LEFT / RIGHT
PRIVACY
OFF
ON
COLOR
B/W
--
AREA SEL / TOP / BOTTOM / LEFT / RIGHT / COLOR /
TRANSP / MOSAIC
--
BURST: OFF / ON
DAY/NIGHT
AUTO
NR NR
CAMERA ID OFF/ON
BURST: OFF / ON
DELAY CNT / DAY-NIGHT / NIGHT-DAY
MODE: Y/C, OFF, Y, C
--
SYNC
LANGUAGE
INT --
ENGLISH / CHINESE / JAPANESE / ESPANOL / PORTUGUESE /
PYCCKNN / FRANCAIS / DEUISCH
CAMERA RESET / BACK / EXIT / SAVE ALL
14 www.observint.com
SECTION 3: AIMING THE CAMERA
SECTION 3
Aiming the Camera
1. Connect the video cable from the camera to a test monitor or to the BNC input on the
DVR.
2. Apply 12 Vdc power to the camera to power it on.
3. Unscrew the bezel until the camera module and housing can be rotated on the base.
4. While observing the video from the camera, adjust the camera to point it at your surveillance target.
5. Position the housing to the LED array and the FOCUS and ZOOM adjusters (varifocal models) are accessible
6. Screw the bezel onto the base tight enough to hold the camera assembly securely in place.
7. If you are installing a CD601BVF / CD601WVF or CD700BVF / CD700WVF camera, use a small blade screwdriver to adjust the focus and zoom if necessary.
Infrared Turret Camera User Manual 15
SECTION 4: CLEANING
SECTION 4
Cleaning
Clean the camera lens and IR lamp shield with an approved glass cleaning solution and a lint free cloth.
•
•
Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a soft cloth.
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing. These may cause damage to the surface over time.
CAUTION
Do not use benzene, thinner or other chemical products on the camera assembly; these may dissolve the paint and promote damage of the surfaces. Before using any chemical product, read the accompanying instructions carefully.
16 www.observint.com
SECTION 5: SPECIFICATIONS
SECTION 5
Model
Sensor
Effective Picture
Elements (H×V)
Horizontal Resolution
Minimum Illumination
S/N Ratio
Scanning System
Synchronous System
Auto-electronic Shutter
Gamma Characteristic
IR Distance
IR Status
IR Power On
Video Output
Auto Gain Control
Power/Current
Lens
Dimensions
Weight
Storage Temperature
Operating Temperature
Specifications
CD600W, CD600B
1/3" CMOS
CD601W, CD601B
1/3" SHARP CCD
CD601WVF,
CD601BVF
1/3" SHARP CCD
768 (H) x 494 (V) 728 (H) x 488 (V) 768 (H) x 494 (V)
0.1 lux F1.2 /
0 lux (with IR LED on)
More than 46 dB
65 ft (with Ø5 x 24 PCS
Infrared LED array )
Under 10 lux by CDS
CDS AUTO Control
600 TV Line
0.1 lux F1.2 /
0 lux (with IR LED on)
More than 48 dB
2:1 interface
Internal, negative sync.
1/60 s ~ 1/100,000 s
0.45
65 ft (with Ø5 x 24 PCS
Infrared LEDs)
- -
- -
1 Vp-p, 75 Ω
0.01 lux F1.2 /
0 lux (with IR LED on)
More than 48 dB
90 ft (with Ø5 x 36 PCS
Infrared LED array)
Under 10 lux by CDS
CDS AUTO Control
12 Vdc (+/-10%) / 350 mA
3.6 mm / F2.0
Ø3.7 x 2.7 (H) in
(Ø94 x 69 (H) mm)
15.9 oz (450 g)
Auto
12 Vdc (+/-10%) / 350 mA
3.6 mm / F2.0
Ø3.7 x 3.15 (H) in
(Ø94 x 80 (H) mm)
15.9 oz (450 g)
-22 ~ 140 °F (-30 ~ 60 °C) RH 95 % max
12 Vdc (+/-10%) / 450 mA
2.8 - 12 mm manual zoom
Ø5.12 x 3.67 (H) in
(Ø131 x 93 (H) mm)
28.2 oz (800 g)
14 ~ 122 °F (-10 ~ +50 °C) RH 95 % max
Infrared Turret Camera User Manual 17
SECTION 5: SPECIFICATIONS
Model
Sensor
Effective Picture
Elements (H×V)
Horizontal Resolution
Minimum Illumination
S/N Ratio
Scanning System
Synchronous System
Auto-electronic Shutter
Gamma Characteristic
IR Distance
Video Output
Auto Gain Control
Power/Current
Lens
Dimensions
Weight
Storage Temperature
Operating Temperature
CD700W, CD700B CD700WVF, CD700BVF
1/3" SONY Super-HAD CCD II 1/3" SONY Super-HAD CCD II
976 (H) x 494 (V)
0.001 lux F1.2 /
0 lux (with IR LED on)
700 TV Line
0.001 lux F1.2 /
0 lux (with IR LED on)
More than 52 dB
2:1 interface
Internal, negative sync.
1/60 s ~ 1/100,000 s
0.45
65 ft (with Ø5 x 24 PCS
Infrared LED array )
1 Vp-p, 75 Ω
90 ft (with Ø5 x 36 PCS
Infrared LED array)
Auto
12 Vdc (+/-10%) / 350 mA 12 Vdc (+/-10%) / 450 mA
3.6 mm / F2.0
Ø3.7 x 2.7 (H) in
(Ø94 x 69 (H) mm)
15.9 oz (450 g)
2.8 - 12 mm manual zoom
Ø5.12 x 3.67 (H) in
(Ø131 x 93 (H) mm)
28.2 oz (800 g)
-22 ~ 140 °F (-30 ~ 60 °C) RH 95 % max
14 ~ 122 °F (-10 ~ 50 °C) RH 95 % max
18 www.observint.com
SECTION 6: TROUBLESHOOTING
SECTION 6
Troubleshooting
Before sending the camera for repair, please check below to make sure that the camera is installed correctly. If it still does not perform adequately, please consult your supplier.
1. No picture on the monitor screen.
a. Check that all connected devices are powered on.
b. Confirm that the voltage is correct.
c. Confirm that the power supply provides enough current to power the camera.
d. Check that all video cables are correctly connected.
2. The picture is not clear.
a. Check that your monitor is correctly adjusted.
b. Confirm that the glass in front of the lens is clean.
If there is dust, dirt or fingerprints on the glass, the image quality will be affected. To clean the glass use a soft, dry and non-abrasive cloth or a commercially available lens cleaning set.
c. Correctly adjust the focus (VF (varifocal) models only.)
3. The picture has interference.
a. The camera may be close to a high voltage source, such as a power generator. b. The BNC cable is not terminated properly. c. The video cables are not connected properly.
Infrared Turret Camera User Manual 19
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 SECTION 1 Features
- 6 1.1 Camera components
- 7 1.2 Camera connections
- 8 SECTION 2 Installation
- 8 2.1 What’s in the box
- 8 2.2 Tools you need
- 9 2.3 Installation instructions
- 16 2.4 OSD Setup (CD700 series only)
- 19 SECTION 3 Aiming the Camera
- 20 SECTION 4 Cleaning
- 21 SECTION 5 Specifications
- 23 SECTION 6 Troubleshooting