VisionQuest VQF70WD Specifications

VisionQuest VQF70WD Specifications
Technical Specifications
Input Formats
Compact Flash® (CF type I&II), Memory Stick®, Memory Stick PRO® ,
Multimedia Card (MMC), Secure Digital (SD), USB Pen Drive.
Supported File Formats JPEG, Motion JPEG AVI, Mp3, MPEG1, MPEG2.
Display
Output
7"LCD monitor:480x234 resolution
Full frame 16:9/4:3 Standard Aspect Ratio, slide show or thumbnail
Image Effects
Rotate, zoom, pan, transitions, slide duration
USB Host
V1.1
Power Input
100V-240V AC, 50-60Hz
Power Output
12V DC, 1.5A
Dimensions
Operating Instructions
VQF70WD
Composite video output
System: PAL/NTSC
Analog 2-channel audio out
Earphone
Stereo Speakers(1Wx2)
Viewing Modes
Weight
Digital Picture Frame
1.3 LBS
9.05"Wx5.9"Hx1.18"D
19
www.visionquestce.com
Appendix (Troubleshooting Guide)
Table of Content
Important Safeguards
2
Frequently Asked Questions
5
Quick Start Guide
6
Contents
7
Connecting to a TV Set
8
Remote Control
9
Insert the memory card
10
Control Functions
11
System setup
15
Glossary of Terms
17
Appendix (Troubleshooting Guide)
18
Technical Specifications
19
Before contacting service personnel, please check possible causes according to the following
instructions.
Symptom
Remedy
1.Power supply not connected;
2.Bad contact between the power plug
and the receptacle;
3.The power of the receptacle is off;
4.Power switch is in the off position.
1.Connect to the power supply.
2.Plug again or replace a receptacle.
No sound
1.Incorrect signal connection;
2.The system is in the mute status.
1.Connect the signals properly.
2.Press the "Mute" button again.
No picture
1.Incorrect signal connection;
2.Incorrect TV status;
1.Connect the signals properly.
2.Adjust the TV/AV status.
1.Wrong selection of TV system;
1.Se tup the TV system see "system
setup/preference page/TV type" for
reference
2.Readjust the color.
3.Check if the video output settings are
correct.
No power
No color
2.Improper color adjustment;
3.Incorrect video output settings.
Remote
control
malfunction
No reader
memory card
1
Possible Cause
1.The remote control is not directed
at the sensor;
2.Low voltage of the RC batteries;
3.There is an obstacle between the
unit and RC.
3.Switch on the receptacle.
4.Slide the power switch to on position.
1.Direct the remote control at the
sensor.
2.Change to a new battery.
3.Remove the obstacle.
1.The memory card is inserted all the 1.Insert the memory card with the
way into the card slot and is facing the correct direction.
wrong direction;
2.The memory card did not insert
2.Insert the memory card completely.
completely.
18
Glossary of Terms
Important Safeguards
Aspect Ratio
The ratio of the length of an image to its width. Most computer screens and digitally shot
images that have an aspect ratio of 4:3.35mm film and some digital cameras shoot images
that have aspect ratio of 3:2.
AVI
Audio Video interleave; a Microsoft®- specified format for saving audio and/ or video clips.
Flash Drive (Pen Drive)
A storage module made of flash memory chips that allow data to be easily transferred from
one device to another.
Flash Memory
A type of non-volatile memory that holds onto is contents even when an electrical charge
is not applied. Flash memory is used in many applications including PDAs, hardware MP3
players, and some digital cameras.
JPEG
Joint Photographic Experts Group; the development group for a compressed 24-bit
color image storage format that also bears its name.
Memory Card
The system used to store images by most digital cameras. Unlike a computer memory card,
this card retains data even without electricity.
Mp3
A compressed digital audio file format. The format enables almost CD quality sound
(depending on the compression ratio) at a fraction of the size of normal audio files.
Mega Pixel
One million pixels. A high mega pixel rating typically equates to a high maximum
performance for graphics, or better quality pictures for digital cameras.
Mp4
A container format allows combining of different multimedia streams into one single file.
Mp4 supports multimedia content such as audio, video, subtitles, and pictures and
advanced content such as animated graphics and DVD-like menus.
Resolution
The amount of pixels that are displayed on a screen measured in pixels horizontal by pixels
vertical, such as 1024x768. The higher the resolution, the more pixels can be displayed
and greater detail is displayed. Lower resolutions are interpreted and may lose detail.
Slideshow
A display of a series of selected images.
Thumbnail
A small representation of a larger graphic often used to display several graphics at once
and allowing easy sorting through images.
USB (Universal Serial Bus)
A protocol for transferring data to and from digital devices. Many digital cameras and
memory card readers connect to the USB port on a computer.
17
IMPORTANT SAFEGUARDS
Signal Word Definitions
DANGER Indicates an imminently hazardous situation, which, if not avoided, will result in death
or serious injury. Usage of this signal word is limited to the most extreme situations.
WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in
death or serious in jury.
CAUTION Indicates a potentially hazardous situation, which, if not avoided may result in
minor/moderate injury or product/property damage. It also alerts against unsafe practices.
WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.
WARNING: To prevent the risk of electric shock, do not remove cover. No user-serviceable parts
inside. Refer servicing to qualified personnel.
READ ALL INSTRUCTIONS BEFORE USE.
WARNING--To reduce the risk of fire, electric shock, or serious personal injury:
• HEED WARNINGS. Adhere to all warnings in the operating instructions and on the Digital Picture
Frame itself.
• WATER AND MOISTURE. Do not use the unit near water or expose to rain or moisture.
• ATTACHMENTS. Use only manufacturer-recommended attachments or accessories.
• ACCESSORIES. Do not place the Digital Picture Frame on unstable cart, stand , tripod, bracket,
or table. The unit may fall, causing injury to you and serious damage to the product.
• VENTILATION. Position the Digital Picture Frame so that its location does not interfere with its
proper ventilation. For example, the unit should not be situated on a bed, sofa, rug or similar
surface that may block the ventilation opening, or placed in a built-in installation, such as a
book-case or cabinet, that may impede the plow of air through the ventilation openings.
• HEAT. Position the Digital Picture Frame away from sources of high heat such as radiators or
stoves.
• POWER SOURCE. Connect the Digital Picture Frame to a power supply only of the type
described in the operating instructions or as marked on the unit.
• GROUNDING OR POLARIZATION. This product may be equipped with a polarized alternating
current line plug (a plug having one blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized plug.
• POWER CORD PROTECTION.
-Mains plug is used as the disconnect device. It shall remain readily operable and should not be
obstructed during intended use.
-Route power cords so that they are not likely to be walked on or
pinched by items placed on or against them, paying particular attention to the point where the cord
attaches to the Digital Picture Frame.
• OUTDOOR ANTENNA GROUNDING .If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA
70, provides information with regard to proper grounding of the mast and supporting structure,
2
System Setup
Important Safeguards
grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors,
location of antenna discharge unit, connection
to grounding electrodes, and requirements
for the grounding electrode. See figure below.
• LIGHTNING. For added protection for this
product during a lightning storm, or when it is
left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent
damage to the product due to lightning and power
lines surges.
Preference page
TV TYPE:
Select TV system. Option include PAL and NTSC, and multi.
AUDIO:
To select the Audio Language. Option include English, French, Spanish, Chinese,
Japanese, Korean, Russian.
Subtitle:
Select the Subtitle Language. Option include English, French, Spanish, Chinese,
Japanese, Korean, Russian.
Default:
Reset all the setting of DPF to init default state.
• POWER LINES. An outside antenna system should not be located in the vicinity of overhead power
lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken to keep from touching such power
lines or circuits as contact with them might be fatal.
• NON-USE. Unplug the power from the outlet when the unit is not in use.
• AVOIDING SURGES. For added protection during a lightning storm, unplug the Digital Picture Frame
from the wall outlet to prevent damage to the product due to power line surges.
• OVERLOADING. Do not overload wall out lets or extension cords.
• OBJECT AND LIQUID ENTRY. The apparatus shall not be exposed to dripping or Splashing and that
no objects filled with liquids, such as Vases, shall be placed the apparatus.
• DAMAGE REQUIRING SERVICE. Seek service by qualified service personnel when:
- The power supply has been damaged.
- Liquid has been spilled onto the Digital Picture Frame.
- The unit has been exposed to rain.
- The unit does not operate normally, or exhibits a marked change in performance.
- The unit has been dropped or physically damaged.
• REPLACEMENT PARTS. When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
• SAFETY CHECK. Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper operating condition.
• WALL OR CEILING MOUNTING. The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
• SERVICING. Do not attempt to service the Digital Picture Frame beyond those means described in
these operating instructions. All other servicing should be referred to qualified service personnel.
.. Preference Page ..
TV Type
Audio
Subtitle
Default
PAI
ENG
Go To Preference Page
Exit setup menu
Exit Setup Menu
Exit Setup Menu
CAUTION-- To reduce the risk of personal injury or product/property damage:
• CLEANING. Clean the outer surface of the Digital Picture Frame (excluding the screen) gently
using a soft cloth dampened with water. Clean the screen only with a specified cleaning solution
for use with products such as laptops and computer monitors. These are available at most retail
consumer electronics stores. Do not clean the inside of the unit.
3
16
System Setup
Important Safeguards
SETUP: General setup
1.TV DISPLAY
NORMAL: Use this mode for viewing standard picture in unaltered proportions.
Which is the standard still image aspect ratio from most Digital Cameras.
Black bars will appear on each side of the screen.
WIDE: Use this mode to standard picture will stretch to fit the screen.
2.OSD Language
Select the OSD( On Screen Display) language (The language for all menus and
on-screen displays). Option include English, French, Spanish, German.
3. Slide Show:
Set the display duration for each image: 1S, 3S, 5S.
.. General Setup page ..
Wide
ENG
3S
TV Display
OSD Lang
Slide Show
Go To General Setup Page
Video Setup:
Quality:
Sharpness:
Select High, Medium, Low
Brightness:
tune the brightness with a progress bar by using LEFT/RIGHT.
Contrast:
tune the contrast with a progress bar by using LEFT/RIGHT.
Hue:
tune the Hue with a progress bar by using LEFT/RIGHT.
Saturation:
tune the Saturation with a progress bar by using LEFT/RIGHT.
This symbol alerts the user of the presence of non-insulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol alerts the user of the presence of important operating and
maintenance (servicing) instructions in the Digital Picture Frame user guide.
CAUTION
TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
- CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING
TO QUALIFIED PERSONNEL.
Condensation
If cold water is poured into a glass, water droplets form on the outside of the glass. This is called
condensation. Condensation may occur on internal operating parts of the product. Condensation
occurs:
• When the product is brought from the outdoors into a warm room, or if it is in a cold room which
is heated quickly.
• If the unit is moved suddenly from an air-conditioned room or car to a hot or humid location.
Should condensation occur, the product may not operate properly. WAIT 1-2 hours (to allow the
internal parts to adjust to the surrounding temperature) before using the product.
.. Video Setup Page ..
Sharpness
Brightness
Contrast
Hue
Saturation
MID
00
00
00
00
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Go To Video Setup Page
15
4
Control Functions Continue
Frequently Asked Questions
Q: How do I set up my Digital Picture Frame?
A: The Digital Picture Frame setup is very easy from “out-of-the-box” to “up-and-running” in a few
short minutes. Just plug the power adapter into the Power In jack on the back of the Digital Picture
Frame and plug the power cord into a standard 100-240 volt AC electrical outlet. Next, insert a
memory card into the appropriate slot on the side and slide the Power Switch to ON.
Q: What memory cards can the Digital Picture Frame read?
A: The Digital Picture Frame can read all popular memory cards in all sizes including the current
large capacity 2 GB cards and above, and card types including:
Compact Flash ® (CF type I & II), Memory Stick ® (MS), Memory Stick PRO ® ,
Multimedia Card TM (MMC), Secure Digital TM (SD).
Q: What media formats does the Digital Picture Frame support?
A: The Digital Picture Frame supports JPEG picture files, Motion JPEG AVI video files, MPEG1,
MPEG2 and Mp3,WMA audio files.
Q: I set up the Digital Picture Frame; why is it not powered on?
A: The adapter is not securely connected to the picture Frame or the Power Switch is not in the ON
position.
Q: I have a memory card in the Digital Picture Frame; why can’t I view the images?
A: First, make sure that the memory card is one of the card formats listed above and that the files
on the card are in one of the supported formats as listed above. Second, turn the Digital Picture Frame
OFF and make sure that the memory card is inserted all the way into the card slot and is facing the
correct direction. Third, turn the frame ON and from the initial card selection menu make sure that
you can select the card. Finally, make certain you are selecting the correct Mode from the next menu:
Picture for still images, Music for Mp3 music, or Video for AVI videos.
NOTE:
1. Some digital cameras save images in non-standard formats. Please refer to your camera’s
instruction manual for details.
VIDEO CONTROL
1.Use '
' Keys to highlight VIDEO icon, Press 'Enter' Button enter VIDEO play
menu.
2.Use / keys to highlight a VIDEO file , then press PLAY button to start to playback the VIDEO file.
[PAUSE]: Press ' / ' to pause during playback, and press Pause again to resume.
[STOP]: Press ' ' to stop playback and press ' ' again to return to the VIDEO file
browse menu.
[FORWARD /REVERSE ] : Press FORWARD/REVERSE to forward /reverse during
playback , and the playback speed will cycle with each press as : 2x, 4x, 8x, 16x,
32x, normal. Press' / ' to pause and press' / ' again to resume.
[
/
]: Press'
/
' to switch playback to previous file .next to next file.
[DISPLAY]: Press 'DISPLAY' to choose the "single elapsed", "single remain"or
"display off"
[ZOOM]:1.Press 'ZOOM' button repeatedly during playback, then the size of image
will change each press in the sequence as: 2X,3X,4X,1/2X,1/3X,1/4X,normal.
2.Use' , , , 'keys to move the zoomedimage as you like. There is a box on
the button right of the screen to indicate the zoom size and corresponding position
of the image.
3. To resume normal playback, press 'ZOOM' repeatedly until the image is in
normal size.
[VOLUME +,-]: Press "VOL+,VOL-"keys to decrease/ increase sound volume.
Q: Why is the picture display slower with some pictures and faster with others?
A: Higher resolution pictures load more slowly. Try using lower resolution pictures or down sample
your images. See your camera’s operating manual for details on down sampling images.
Q: Can I insert multiple memory cards?
A: Yes. Turn on the unit after inserting memory cards. The first screen will display which types of
memory cards are in the slots. Use the Remote Control to the desired memory card.
Q: Does the Digital Picture Frame have built-in memory?
A: No, a compatible memory card must be used.
5
Background music play
1.Use left/right keys to highlight "file" icon is in the "select mode" inside. Press
ENTER keys tolist files .
2.Press "PROG" key to make all documents compositor according to the document type.
3.Use UP/DOWN and
/
keys to highlight desired Audio file, then press ENTER
to start to playback the Audio file, and use "REPEAT" keys to setup repeat mode.
4.Use UP/DOWN and
/
to highlight image file then. Press ENTER to start to
playback image file, and "slide show" keys to play all image.
14
Quick Start Guide
Control Functions
ZOOM
Press "ZOOM" button repeatedly during playback, then the size of image will change
each press in the sequence as: 100%, 125%, 150%, 200%,50%, 75%.
After the image is enlarged, use the arrow buttons" , , , " to move the image
so that you can view different of the enlarged image.
To resume normal playback, press"ZOOM" repeatedly until the image is in normal size.
4:3/16:9 Switch the aspect ratio the screen .
To begin using the Digital Picture Frame, follow these instructions:
1. Pull the stand to make it better support the frame.
4:3 In the WIDE mode , Change view to standard 4:3 aspect ratio. Use this mode for
viewing standard photos in unaltered proportions. Recommend to do not use this
mode is In the NORMAL mode.
16:9 Normal the aspect ratio the screen.
NOTE: For WIDE mode and NORMAL mode see' SETUP/TV DISPLAY'
4:3
2. Plug one end of the AC Adapter into the Digital Picture Frame
and plug the other end into a standard 100-240 volt AC electrical
outlet.
3. Insert a memory card into the appropriate slot.
NOTE: The card will only fit in one direction; do not force it. The
card should have a firm, snug fit if properly inserted.
16:9
MUSIC CONTROL
1.Use / Keys to highlight MUSIC icon, Press 'Enter' Button enter music play menu.
2.Use / keys to highlight a WMA file , then press PLAY button to start to playback
the WMA file.
[PAUSE]: Press ' / ' to pause during playback, and press Pause again to resume.
[STOP]: Press '
' to stopping playing. Then the time showing on the bottom right
will switch to 00:00/00:00
[FORWARD /REVERSE ] : Press FORWARD/REVERSE to forward /reverse during
playback , and the playback speed will cycle with each press as : 2x, 4x, 8x, 16x,
32x, normal. Press' / ' to pause and press' / ' again to resume.
[UP/DOWN]: Use / Keys to highlight an WMA file when the selected one is
playing by using / keys . Then press ENTER, the highlight WMA will be
played instead of the previous one.
[VOLUME +,-]: Press "VOL+,VOL-"keys to decrease/ increase sound volume.
13
ON/OFF
4. Slide the Power Switch to the ON position.
5. If not already selected, scroll to the appropriate memory card
type on the first menu screen by using the Arrow Buttons on the
Remote Control.
6. Press the ENTER Button to confirm the selection.
7. On the next menu, scroll using the Arrow buttons to select
PHOTOS.
8. On the next menu, press SLIDESHOW on the Remote Control
to display images. For more details or instructions on using the
MUSIC, MOVIES, or FILES menus, refer to the “Control Functions”
section.
6
Contents
Control Functions Continue.
PHOTO:
MUSIC:
VIDEO:
FILE:
:
SD/MMC SLOT
PREV/UP ARROW
/LEFT ARROW
CF
USB
MS
- C +
DC 7-12V
AUDIO/VIDEO
OUTPUT
PUT: FLASH DRIVE USB
AV OUT
MENU BUTTON
THUMBNAIL SCREEN
CF SLOT
MENU
NEXT/DOWN ARROW/
RIGHT ARROW
MENU:
NOTE:
SD / MMC
ENTER
ENTER
JPEG still image viewing and slide show playback.
MP3/WMA audio playback.
Video file Playback.
View the file structure on the memory card.
Use the Left and Right Arrows on the Remote Control or on the Control Panel to
select a viewing mode.
Press"MENU" button return to main menu.
This menu only have to just appear is the memory card contain two kind of above
the support document.
In PHOTO mode, a thumbnail screen will appear to enable easy selection of images. This mode
displays a set of up to 9 thumbnail image on the screen at a time.
Use the Arrow Buttons on the Remote Control Panel to select an image.
MS, MS PRO
AC ADAPTER JACK
EARPHONE
Prev Next
ENTER
MENU
Press the ENTER Button from the Remote Control or the Control Panel to view the
selected image at full screen size.
Press "MENU" button return to main menu.
IMAGE CONTROLS
ON/OFF
SPEAKERS
7
POWER SWITCH
When viewing an image:
Previous: Press the Previous Button on the Remote Control or the Control Panel to return
to the previous image.
NEXT: Press the NEXT Button on the Remote Control or the Control Panel to skip to the
NEXT image.
Slide show: In the press the SLIDE SHOW Button on the Remote Control to begin a
“slide show” style playback of all image on the selected memory card..
STOP: Press the STOP Button on the Remote Control or the Control Panel to stop image
playback and return to the Thumbnail Screen
MENU
Press "MENU" button to image file browse menu.
ROTATE When viewing a full screen, Press direction button on the remote: UP(vertically mirror);
DOWN(horizontally mirror),LEFT(90 degree clockwise),RIGHT(90 degree anticlockwise)
12
Control Functions Continue
Connecting to a TV Set
CARD SELECTION MENU
At startup, a menu screen appears for selection of the memory card:
ENTER
MENU
AV OUT
:
Use the Right and Left Arrows on the Remote control or on the control panel to select the
correct memory card type or USB Flash driver.
RED
WHITE
Yellow
ENTER: Press the Enter button to confirm.
NOTE:
1. Some digital cameras save images in non-standard formats. Please refer to your camera’s
instruction manual for details.
2. The SD icon will not be highlighted if no SD inside, The MS/PRO,CF,USB icon is same too.
VIDEO IN
AUDIO IN
MODE SELECTION MENU
The next menu allows Selection of the playback mode.
11
8
Insert the memory card
Remote Control
1
MENU
2
3
4
MUTE
DISPLAY
4:3
16:9
5
6
7
8
9
10
11
12
23
/
22
21
20
19
18
17
16
15
VOL
ENTER
SETUP
ZOOM
SLIDE SHOW
AUDIO
SUBTITLE
PROG
13
14
REPEAT
DIGITAL PICTURE FRAME
1. MENU: Press MENU Return to the previous
menu.
2. MUTE: Press MUTE to sound off.
3. Display: Press Display to choose the"single
elapsed", "single remain" or"display off".
4. 4:3/16:9 : Press 4:3/16:9 to adjust aspect
ratio of screen display.
5.7.8.9.22: UP/DOWN/LEFT/RIGHT/ENTER:
USE UP/DOWN/LEFT/RIGHT Keys to
navigate all on-screen display, Press ENTER
to confirm selections.
6. Stop: Press STOP to stop video playback.
10. SETUP: Press SETUP to access setup menu.
11. PREV:Press PREV to previous image /Mp3/
VIDEO.
12.NEXT:Press NEXT to next image/VIDEO.
13. Repeat: Press Repeat to Repeat mode.
14.PROG: Press PROG to show by file browse.
15.SUBTITLE:Press the SUBTITLE to select the
subtitle language.
16.AUDIO: Press AUDIO to select the audio language.
17.
:Press"
" to reverse at different times during.
18.
: Press"
" to forward at different times during.
19. Slide Show: Press Slide Show to begin displaying picture in a slide show
20.Zoom: Press Zoom to zoom in/out to magnify or reduce you view.
21. Volume Controls: Adjust volume for audio and video file
23. Play/Pause: Press Play/Pause once to Pause video playback and press Play/Pause
again to resume Playback.
1. Insert the SD/MMC
correct direction.
2. Insert the
direction.
HOW TO REPLACE THE BATTERY
STEP 1: PUSH THE BUTTON TOWARD LEFT;
STEP 2: PULL THE BATTERY LOADER OUT.
2
BATTERIES
INCORRECT USE OF BATTERIES MAY CAUSE THEM TO LEAK, CORRODE OR EXPLODE.
Be sure to place the batteries in the correct direction.
It is dangerous to charge/heat/open or short-circuit the batteries.
Do not leave dead or expired batteries or mix old/new batteries.
When not using the remote control for a long duration of time, remove the batteries. When operating
range becomes reduced, replace all batteries with new, fresh ones.
If leakage from the battery occurs, wipe the battery liquid from the battery compartment, then replace.
9
memory card with the correct
3. Insert the MS/MS-PRO
the correct direction.
CR2025
1
CF
memory card with the
10
memory card with
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement