Crosley | 137218900A | Operating instructions | Crosley 137218900A Operating instructions

Crosley 137218900A Operating instructions
se
Guide
Guia
Care Guide
'utilisation
et
'entret=en
m
e Uso y Cuidado
Printed in U.S.A.
www.crosley.com
P/N 137218900A
(0906)
Table of Contents
Product Registration ..............................................................
2
Important Safety Instructions ............................................
2-4
Drying Procedures .............................................................
4-5
Operating Instructions .......................................................
5-7
Features ................................................................................
8
Dryer Settings Chart ..............................................................
8
Product
Care and Cleaning ................................................................
Common Drying Problems ..................................................
Avoid Service checklist ........................................................
Warranty ............................................................................
Francais ..............................................................................
Espa_ol ...............................................................................
9
10
11
12
13
24
Record
Read all instructions before using this appliance. This book
contains valuable information about:
Read and Save These Instructions
Record Your Model and Serial Numbers
• Operation
Care
Service
The model and serial numbers of your dryer are found on the
dryer serial plate located of the left side of the door opening.
Record and retain these numbers.
Keep it in a safe place.
Model
Serial
Number
This Use and Care Guide provides general operating instructions for your dryer, it also contains information about features for several other models. Your dryer may not have every
feature included.
Number
Purchase
Use the dryer only as instructed in this Use & Care Guide and
the Operating Instructions included with your dryer.
Date
Important
Recognize
labels
safety
symbols,
words
and
Safety items throughout this manual are labeled
with a WARNING or CAUTION based on the risk
type as described below:
This symbol alerts you to situations that may cause serious
body harm, death or property
damage.
This symbol alerts you to situations that may cause bodily
injury or property damage.
Safety
Instructions
For your safety the following information in this
manual must be followed to minimize the risk of fire or explosion or to
prevent property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
o Do not try to light any appliance.
Do not touch
Clear the room, building
immediately
Save these
future
instructions
reference.
for
any electrical
switch;
do not use any phone
in
your building.
Follow the gas supplier's
If you cannot
ment.
Installation
or area of all occupants.
call your gas supplier
from a neighbor's
phone.
instructions.
reach your gas supplier, call the fire depart-
and service must be performed
by a qualified
installer, service agency or the gas supplier.
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish
a list of substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to
warn customer of potential exposure to such substances. Included in this list are soot and carbon monoxide, both of which
may be produced by the use of this product.
2
Important
Safety
Instructions,
con't
240 v Electric Dryer
120 v Gas Dryer
Grounding
type
wall receptacle
14-30 R
4-wire
UL-approved service
cord must be installed
j_
Do not, under
on electric dryers (not
provided with unit
except those
manufactured for sale
in Canadak
s_ ]
anYcut,
clrcums_anCeSremove,
or bypass the
grounding prong.
J
(fused 30 amp)
Power cord with
3-prong grounded
plug
Avoid fire hazard or electrical shock. Do not use an adaptor plug or extension cord or remove grounding prong
from electrical power cord. Failure to follow this warning can cause serious injury, fire or death.
To reduce the risk of fire, electrical shock, or injury to persons when using this dryer, comply with the basic
warnings listed below. Failure to comply with these warnings could result in serious personal injuries.
You can be killed or seriously injured if you don't follow these Important Safety Instructions:
PREVENT FIRE
• Do not dry items that have been previously cleaned in,
soaked in, or spotted with gasoline, cleaning solvents,
kerosene, waxes, etc. Do not store these items on or near
the dryer. These substances give off vapors that could ignite
or explode.
• Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to a
chemical reaction that could cause a load to catch fire.
• Do not continue to use the dryer is you hear squeaking,
grinding, rubbing or other unusual noises. This could be a
sign of mechanical breakdown and lead to fire or serious
injury. Contact a qualified technician immediately.
• Failure to comply with these warnings could result in fire,
explosion, serious bodily injury and/or damage to the rubber or plastic parts of the dryer.
PROTECT CHILDREN
• Do not dry articles containing rubber, plastic or similar
materials such as bras, galoshes, bath mats, rugs, bibs,
baby pants, plastic bags and pillows that may melt or burn.
Some rubber materials, when heated, can under certain
circumstances produce fire by spontaneous combustion.
• Clean the lint screen before or after each load. The interior
of the dryer, lint screen housing and exhaust duct should be
cleaned approximately every 18 months by qualified service
personnel. An excessive amount of lint build-up in these
areas could result in inefficient drying and possible fire. See
Care and Cleaning.
• Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is used
near children. As children grow, teach them the proper,
safe use of all appliances.
• Destroy the carton, plastic bag and other packing materials after the dryer is unpacked. Children might use them
for play. Cartons covered with rugs, bedspreads or plastic
sheets can become airtight chambers.
• Do not operate the dryer if the lint screen is blocked, damaged or missing. Fire hazard, overheating and damage to
fabrics can occur.
- FIRE HAZARD - A clothes dryer produces
combustible lint. The dryer must be connected to an outdoors
exhaust. Regularly inspect the outdoor exhaust opening and
remove any accumulation of lint around the opening and in
the surrounding area.
• Do not obstruct the flow of ventilating air. Do not stack or
place laundry or throw rugs against the front or back of the
dryer.
• Do not spray any type of aerosol into, on or near dryer at
any time.
• Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
Keep laundry products out of children's reach. To prevent
personal injury, observe all warnings on product labels.
o
Before the dryer is removed from service or discarded, remove the dryer door to prevent accidental entrapment.
o
Failure to comply with these warnings could result in serious personal injuries.
PREVENT INJURY
o
• To prevent shock hazard and assure stability during operation, the dryer must be installed and electrically grounded
by a qualified service person in accordance with local
codes. Installation instructions are packed in the dryer for
the installer's reference. Refer to INSTALLATION INSTRUCTIONS for detailed grounding procedures. If the dryer is
moved to a new location, have it checked and reinstalled
by a qualified service person.
• To prevent personal injury or damage to the dryer, the
electrical power cord of a gas dryer must be plugged into a
properly grounded and polarized 3-prong outlet. The third
grounding prong must never be removed. Never ground
the dryer to a gas pipe. Do not use an extension cord or an
adaptor plug.
Important
Safety
Instructions,
con't
A thermal limiter switch automatically turns off the motor
in the unlikely event of an overheated situation (electric
dryers only). A service technician must replace the thermal
limiter switch after correcting the fault.
Failure to comply with these warnings could result in serious personal injuries.
• ALWAYS disconnect the dryer from the electrical supply
before attempting any service or cleaning. Failure to do so
can result in electrical shock or injury.
Do not use any type spray cleanser when cleaning dryer
interior. Hazardous fumes or electrical shock could occur.
To prevent injury, do not reach into the dryer if the drum is
moving. Wait until the dryer has stopped completely before
reaching into the drum.
PREVENT INJURY AND DAMAGE TO THE DRYER
All repairs and servicing must be performed by an authorized servicer unless specifically recommended in this
Owner's Guide. Use only authorized factory parts.
Do not tamper with controls.
Do not install or store the dryer where it will be exposed to
the weather.
Drying
Procedures
To reduce the risk of fire, electric shock or injury to persons, read the IMPORTANT SAFETYINSTRUCTIONS
in this Use and Care Guide before operating your dryer.
.
_
_ The instructions appearing in this Use and Care
Guide are not meant to cover every possible condition and
situation that may occur. Common sense and caution must
be practiced when installing, operating and maintaining any
appliance.
,
Check that the lint filter is dean and in place.
Prepare load for drying.
Dry items of similar fabric, weight and construction in
the same load.
Separate dark items from light-colored items. Separate
items that shed lint from those that attract lint.
Check for stains which may not have been removed in
washing. Repeat stain removal process and wash again
before drying. Dryer heat may permanently set some
stains.
Placedelicate or small items in a mesh bag.
Clean the lint filter after
every load.
,
(Mesh bag not included.)
Be sure buckles, buttons and trim are heatproof and
won't damage the drum finish. Close zippers; fasten hooks and Velcro®-Iike fasteners. Tie strings and
sashes to prevent snagging and tangling.
Load the dryer and close the door.
Load items loosely. The average wet load will fill the
drum 1/3 to 1/2 full. Items need room to tumble freely
for even drying and less wrinkling.
If desired, place a dryer fabric softener sheet on top of
the load at the beginning of the cycle.
To save energy and time and avoid uneven drying and
wrinkling, do not overload the dryer.
When drying large items, dry only two or three items
at a time. Fill out the load with small and medium sized
items.
For delicate or very small loads, add two or three similar items to improve tumbling action.
4.
Select the appropriate
load.
cycle and settings
To return to factory settings, press the Pause/Cancel
and Select buttons at the same time and hold until the
for each
signal sounds.
Over-drying can cause wrinkles, shrinkage, lint,
harshness and a build up of static electricity.
o Hills
• Turn the cycle selector knob in either direction to select
the cycle desired. The indicator for that cycle will be
illuminated.
it*
0 [g<,d-lJlizl!s
0 I_10fr_A)@
0 l@lim_
0 lorrml
0 Sluinld;u_d
0 v
0 bw
0 lI;4s[JIy
0 I>l'l,
ssSavIzIl
0
0
O Nol!I_mt
O rmm/)
O Cy<bS £_,nal
O
0
The estimated drying time for Auto Dry cycles or the
actual drying time for Timed Dry cycles will be displayed.
A suitable drying temperature, dryness level and options will automatically be indicated for the cycle selected. See the "Dryer Settings Chart" for more details.
To change the drying temperature and dryness level,
press the TEMP or DRYNESS buttons to scroll to the
desired settings.
To select or delete an option, press OPTIONS; then,
while the indicator is blinking, press Select. The indicator will light when the option has been selected. It will
no longer be lighted when the option has been deleted.
0
(
t
8
Press and hold both for ten seconds
to return to factory settings.
5.
6.
f£/'l
_.l®_ ::'_To provide the best care for your laundry, not every
setting or option is available with every cycle. If a setting or
option is not available for the cycle selected, the indicator will
not light.
Start the cycle.
,,To add or remove items when the dryer is running,
open the door. The dryer will stop when the door is
opened. Allow the drum to come to a complete stop
before reaching inside.
Close the door and press Start to resume the cycle.
When the cycle ends, remove items immediately
and hang or fold.
Clean the lint filter after every load.
Adjustments made to a cycle will be remembered and
recalled each time that cycle is selected in the future.
OPERATING
INSTRUCTIONS
estimated
dma
o Hiih
0 I_%I-HiIN
0 r'_Iolr_I)_y
0 Ivledum
0 Ho_mal
0 ShdnkQua_d
0 {ow
0 Nolleat
0 Ix_ssQ_'y
0 [)amrs
0 PIessSaw=I
0 (ydeSilnal
T[I_1I>
{)RYNhSS
OPI'IONS S(_l(_ t
I__@__/
0
SIART
0
0 100i >
0 I
i_ :
0
s
F
0 << i I@
IPa_se
(an(:el
This manual covers many models and not all cycles, options, or features listed are available on
every model. Console shown above for reference only. Your model may differ.
Cycle Selection
Turn the cycle selector in either direction to the cycle desired.
For best
results
Follow the fabric care label
instructions on items to be
washed.
To change the cycle once it has begun, press the Pause/
Cancel button twice before selecting a new cycle. Just
turning the cycle selector knob to another selection will not
change the cycle. If the selection is changed after the cycle
starts, the indicator lights will blink, and the signal will beep.
The signal will beep and the status lights will flash, but the
original cycle will continue.
This manual covers many models and not all cycles, options, or features listed are available on
every modek Console shown above for reference only, Your model may differ,
Cycle Selection,
continued
Auto Dry Cycles
Auto Dry cycles take the guesswork out of selecting the
correct drying time for each load. Moisture sensing bars at
the back of the dryer drum sense the moisture level of the
load as it tumbles through the heated air. With Auto Dry
cycles, the load will automatically be dried at the selected
temperature to the desired dryness level. Auto Dry cycles
save time and energy and protect fabrics.
The estimated drying time will be displayed for about 5
minutes. Then the outside of the display will light up in a
circular track to indicate the drying time is automatically
being determined by the sensors. When the load has reached
the selected dryness level, it will continue to tumble during
a cool clown period. This helps reduce wrinkling and makes
items easier to handle during unloading.
Drying time varies depending on size and dampness of
load and fabric type. If the load is too small or almost dry,
the moisture sensing bars may not detect enough moisture
to continue the cycle and the cycle may end after a few
minutes. If this occurs, select a Timed Dry cycle.
Room temperature and humidity, type of installation and
electrical voltage or gas pressure can also affect drying time.
Towels
Select this Auto Dry cycle for towel loads.
Normal
Select this Auto Dry cycle for cotton items.
Perm Press
Select this Auto Dry cycle to dry cottons and blends with a
no-iron finish.
Delicate
Select this Auto Dry cycle for knits and delicate items.
Timed Dry Cycles
- FIRE HAZARD - To avoid fire hazard, do not
use heat to dry items containing feathers or down, foam rubber, plastics similarly textured, rubber-like materials. Use the
Timed Dry cycle and the Air Fluff/No Heat setting.
BuT
Select this cycle to dry a comforter, blanket, sleeping bag or
similar item.
Quick
Select this cycle to quickly dry a small load made up of
just a few items. It provides approximately 20 minutes of
tumbling followed by a 10-minute cool clown period.
Timed Dry
To manually select the drying time for any load, turn the
knob to a numbered setting. Drying times from 15 to 90
minutes are available in 15-minute increments. You will
not be able to select a cycle or dryness level. Timed Dry is
recommended when using the No Heat option.
Cycle Settings
return to factory settings, press the Pause/Cancel and Select
buttons at the same time and hold until the signal sounds.
For best
results
Follow the fabric care label
instructions on items to be
washed.
To change the Dryness level once the cycle has
begun, press the Pause/Cancel button once, make the new
selection and press Start again.
Select the Normal
Appropriate Temperature, Dryness level and Options will
automatically be displayed for each cycle. The settings can be
changed before the cycle is started.
If changes are attempted after the cycle starts, the lights will
blink, the signal will beep and "Err" will be displayed.
Drying Temperature
To change the preset temperature, press the TEMP button
to scroll to the desired setting.
dryness level for most Auto Dry cycles.
Occasionally a load may seem too damp or over-dried at the
end of the cycle. To increase drying time for similar loads in
the future, select More Dry. For loads requiring less drying
time, select Less Dry.
Select Damp for items you wish to partially dry before hanging or ironing.
Cycle Options
To protect your fabrics, not all temperatures are available
with every cycle.
: To select or delete the Shrink Guard, Press Saver, or Cycle
: Signal, press OPTIONS until the blinking light indicates the
desired option. Then, while it is blinking, press Select. The
The temperature selected for the cycle will be remembered
indicator will light when the option has been selected. It will
and recalled each time that cycle is selected in the future. To
no longer be lighted when the option has been removed.
return to factory settings, press the Pause/Cancel and Select
buttons at the same time and hold until the signal sounds.
Not all options are available on every model or are compatible
with every cycle. The indicator will not light if the option is
To change the temperature once the cycle has begun,
not available with that cycle.
press the Pause/Cancel button once, make the new selection and press Start again.
To change the options once the cycle has begun,
High
press the Pause/Cancel button once, make the new selecHigh is recommended for sturdy fabrics.
tion and press Start again.
Med-High
Med-High is recommended for regular fabrics.
The options selected for the cycle will be remembered and
Medium
recalled each time that cycle is selected in the future. To
Medium is recommended for wrinkle free, permanent press return to factory settings, press the Pause/Cancel and Select
and lightweight fabrics.
buttons at the same time and hold until the signal sounds.
Low
Shrink Guard
Low is recommended for delicate fabrics.
Select Shrink Guard to lower the initial drying temperature.
No Heat
Add it to the Soft Heat option to further protect fabrics
This setting (no heat) should only be used with a Timed
from overdrying.
Dry cycle to dry items containing feathers, down, foam
Press Saver
rubber, plastics or rubber-like materials; to refresh clothing,
Select Press Saver if the dried load might not be removed
stuffed animal, pillows or blankets; and to dust draperies.
promptly at the end of the cycle. The dry load will continue
Dryness Level (Auto Dry)
tumbling without heat for 30 minutes to help reduce
To change the preset level, press the Dryness button to scroll
wrinkling. When the Cycle Signal is selected, a beep will
to the degree of dryness desired.
be heard periodically. The load may be removed any time
To protect your fabrics, not all Dryness levels are available
during Press Saver.
with every cycle. If a Dryness level is not appropriate for the
Cycle Signal
cycle, it cannot be selected.
A signal will sound at the end of the cycle and periodically
The Dryness level selected for the cycle will be remembered
and recalled each time that cycle is selected in the future. To
during Press Saver if this option is selected.
Features
End of Cycle Signal
A signal will sound at the end of the cycle and periodically
during Extended Tumble (some models) at the volume level
selected.
Drum Light (some models)
The drum light will come on whenever the door is opened to
illuminate the drum during loading and unloading. Closing
the door turns off the light.
Q Control Lock
To avoid having someone accidentally start the dryer, press
OPTIONS and Select at the same time and hold for 10
seconds until "L,O_" is displayed alternately with the
estimated cycle time. To unlock the controls, press OPTIONS
and Select at the same time and hold 10 seconds until
"L,O_" is no longer displayed.
Drying Rack (some models)
Status Display/Status Lights
The estimated total cycle time will be displayed when the
cycle is selected. The estimated remaining cycle time is
displayed during the cycle. The following indicators may be
lighted during the cycle:
moisture sensing
bars
Use the drying rack to dry items which should not be tumble
dried. Insert the rack into the dryer drum, resting the back
support on the moisture sensor bars and the front legs on the
air grill.
• Drying
Cool down
Press saver
Clean Lint Filter
Control O
Place items to be dried on top of the rack, leaving space
between items and not allowing them to hang over the sides
or through the holes. The weight should not exceed 10 Ibs
(4.5 kg). Select the air (no heat) setting for items containing
plastic, foam rubber, rubber-like materials, feathers or down.
Reversible Door
Your dryer is equipped with a reversible door. The door can
be hinged on the right or left side.
When items are dry, remove the rack and store it in a convenient location.
For step-by-step instructions on DOOR REVERSAL,
refer to the Installation Instructions supplied with this dryer.
Dryer
Setting
Chart
These Temperature,
Dryness levels and Options are available with the following cycles:
Estimated Cycle Duration**
Towels
Bulky
Normal
Perm Press
Delicate
Quick
Timed Dry
60 min
45 min
50 min
40 min
20 min
30 min
15-90 min
,/
,/
Temperature
High
,/*
Med-High
,/
,/
,/
,/*
,/
,/
,/*
Medium
,/*
,/
,/*
,/
,/*
,/
Low
,/
,/
,/
,Z*
,Z
,Z
No Heat
,/
Dryness
More Dry
¢"
¢"
Normal
,Z*
,Z*
,Z*
,Z
Less Dry
,Z
,Z
,Z*
Damp
,/
,/
,/
Options
Shrink Guard
Press Saver
Cycle Signal
_'Available selections
* Factory presets
**Estimated cycle duration is based on default dryness level and factory settings for electric dryers. Displayed cycle
duration may differ slightly on gas models.
Care and
Cleaning
- FIRE HAZARD - A clothes
dryer produces combustible lint. The dryer
must be connected to an outdoors exhaust.
Regularly inspect the outdoor exhaust opening and remove any accumulation of lint
around the opening and in the surrounding
area.
To reduce risk of fire or serious injury to persons or property,
comply with the basic warnings listed in the Important Safety Instructions and
those listed below.
•
Before cleaning the dryer interior, unplug the electrical power cord to avoid
electrical shock hazards.
Do not use any type spray cleanser when cleaning the dryer interior. Hazardous fumes or electrical shock could occur.
INSIDE
= Clean the lint filter after every load. Lint build-up on the filter restricts air
flow, which causes longer drying times. The filter is located at the bottom
of the door opening. Remove by pulling straight up. Remove the lint and
replace the filter.
Occasionally a waxy build-up may form on the lint filter and/or moisture
sensing bars from using dryer-added fabric softener sheets. To remove this
build-up, wash them with warm, soapy water. Dry the filter thoroughly and
replace. Do not operate the dryer without the lint filter in place.
If the dryer drum becomes stained from noncolorfast fabrics, clean the
drum with a damp cloth and a mild liquid household cleanser. Remove
cleanser residue before drying the next load.
Every 18 months an authorized servicer should clean the dryer cabinet
interior and exhaust duct. These areas can collect lint and dust over time.
Clean the lint filter after
An excessive amount of lint build-up could result in inefficient drying and
possible fire hazard.
every load.
OUTSIDE
Clean the cabinet with mild soap and water. Never use harsh, gritty or
abrasive cleansers.
If the cabinet becomes stained, clean with diluted chlorine bleach (1 part
bleach to 8 parts water). Rinse several times with clear water.
Remove glue residue from tape or labels with a mixture of warm water and
mild detergent. Or, touch residue with the sticky side of the tape or label.
When cleaning chrome parts use a window cleaner with ammonia or mild
soap and water.
Before moving the dryer, place a strip of cardboard or thin fiberboard under the front leveling legs to prevent damage to the floor.
Do not store or place laundry
products on top of dryer at any time. They can
damage the finish or controls.
Common
Drying
Problems
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage.
For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.
PROBLEM
POSSIBLECAUSES
Greasy, oily
stains
o Fabricsoftener sheet.
Lint
_ Overloading.
o
Overdrying causes static
electricity.
o
Lint screen not clean when
o
Pilling
(Fibers break off,
ball up and cling
to fabric.)
o
cycle began.
Lint is attached to "pills."
Overdrying.
SOLUTIONS
o
o
o
PREVENTIVE MEASURES
Rub fabric softener stains with bar
Add a few bath towels to small loads for
soap. Rinse and rewash.
proper tumbling.
Some "silk-like" fabrics should be air
dried.
Use proper drying temperature.
Place fabric softener sheet on top of load
before starting the dryer.
Reduce load size and rewash using
liquid fabric softener in the final
rinse.
Or, add a fabric softener sheet and
tumble without heat.
Use lint brush or roller to remove
lint.
Use a lint brush or shaver to remove pills,
_ Do not overload dryer.
_ Use fabric softener in washer or dryer to
reduce static electricity.
Remove items when they are slightly damp
to avoid overdrying.
Check that lint filter is clean and in place.
Use fabric softener to lubricate fibers.
o When ironing, use spray starch or fabric
finish on collars and cuffs.
Turn items inside out to reduce abrasion.
Shrinking
Temperature too high.
Overdrying.
Irreversible condition.
Follow fabric care label directions.
If shrinking is a concern, check load often.
Remove items while slightly damp and
hang or lay flat to complete drying.
Block knits into shape.
Wrinkling
Overloading.
Leaving items in dryer after
cycle ends.
Reduce load size and tumble at
medium or low heat for 5-10
minutes.
Remove items immediately. Hang
or fold.
Do not overload dryer.
Remove items as soon as cycle ends.
10
Avoid
Service
Checklist
Before calling for service, review this list. It may save both time and expense. The list includes common occurrences that are
not the result of defective workmanship or materials in this dryer.
OCCURRENCE
POSSIBLECAUSE
SOLUTION
Dryer does not start.
Electrical power cord is not securely plugged in or plug
may be loose.
Make sure the plug fits tightly in wall outlet.
House fuse blown or circuit breaker tripped.
Reset circuit breaker or replace fuse.
Make sure electrical line is not overloaded and the dryer is on a
separate circuit.
Dryer runs but won't
heat.
Drying cycle takes too
long, outside of the
dryer feels too hot or
Thermal limiter tripped.
Call authorized service person for replacement.
There are 2 house fuses in the dryer circuit. If 1 of the 2
fuses is blown, the drum may turn but the heater will not
operate. (electric models)
Replace fuse.
Gas supply valve is not open (gas models).
Check to make sure supply valve is open. See INSTALLATION INSTRUCTIONSfor procedure.
Dryer does not have enough air supply to support the
burner flame (gas models).
See INSTALLATION INSTRUCTIONS.
LP gas supply tank is empty or there has been a utility
Refill or replace tank.
interruption of natural gas (gas models).
Dryer should heat when utility service is restored.
Lint filter is clogged with lint.
Make sure all lint has been removed from the dryer lint filter before
starting each cycle.
Exhaust duct requirements have not been met.
Exhaust duct must be at least 4 inches in diameter and made of rigid
or semi-rigid metal.
smells hot.
When in place, the duct must have no more than two 90 ° bends and
must not exceed length listed in INSTALLATIONINSTRUCTIONS.
Excessivewrinkling.
Scratching or chipping of
the drum finish,
Electric dryer is connected to a 208 volt circuit.
Drying time will be 20% longer than drying on a 240 volt circuit.
Drying procedures have not been followed.
See "Operating
Outside exhaust hood or exhaust duct may be clogged
or restricted.
Clean out any obstruction.
High humidity.
Use a dehumidifier
Dryer is overloaded.
Do not overload. See "Operating Instructions."
Items left in dryer too long.
Remove items as soon as cycle ends.
Insufficient sorting of items.
See "Operating
Drying temperature too high.
Follow fabric care label instructions.
Foreign objects such as coins, pins, clips or buttons are
inside the dryer.*
Always remove foreign objects from pockets before laundering.
Remove objects from drum and restart dryer.
Permanently attached items such as belt buckles, zippers
and fasteners may be hitting the inside of the drum.*
It may be necessary to sew a scrap of material securely around ornaments before drying to prevent scratching and damage to the dryer.
Instructions."
near the dryer.
Instructions."
*Drum damage caused by foreign objects or permanently attached items is not covered by the warranty.
11
Yourapplianceiscoveredby aoneyearlimitedwarranty.Foroneyearfromyouroriginaldateof
purchase,
CrosleyCorproationwill payallcostsfor repairingor replacinganypartsof thisappliancethat proveto
bedefectivein materialsorworkmanshipwhensuchapplianceis installed,usedandmaintainedin
accordance
with the providedinstructions.
Exclusions
This warranty
does not cover the following:
1.
Products
with original
2.
Product that has been transferred
Canada.
serial numbers
that have been removed,
from its original
3.
Rust on the interior
or exterior
4.
Products
"as-is" are not covered
purchased
5.
Food loss due to any refrigerator
6.
Products
7.
Service calls which
used in a commercial
not in ordinary
8.
Service calls to correct
9.
Expenses for making
etc.,which
party or removed
determined.
outside
the USA or
or freezer failures.
setting.
malfunction
the installation
the appliance
in materials
or workmanship,
with the provided
or to instruct
for servicing,
or for appliances
instructions.
you how to use your appliance.
such as removal
when it is shipped
appliance
or other cosmetic
or defects
than in accordance
of your appliance
accessible
are not a part of the appliance
knobs, handles,
be readily
by this warranty.
use or used other
10. Service calls to repair or replace
owner to another
or cannot
of the unit.
do not involve
household
altered
of trim, cupboards,
shelves,
from the factory.
light bulbs, air filters, water filters,
other consumables,
or
parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance
cabinets, walls, etc.
or home incurred
13. Damages caused by: services performed
genuine Crosley parts or parts obtained
external
during
installation,
including
by unauthorized
service companies;
from persons other than authorized
causes such as abuse, misuse, inadequate
power supply, accidents,
but not limited
to floors,
use of parts other than
service companies; or
fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.
CROSLEY CORPORATION SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN
LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS THAT VARY FROM STATETO STATE.
If You Need
Keep your receipt, delivery
should service be required.
Service
Service under this warranty
numbers below.
This warranty
only applies
In Canada, your appliance
any obligations
under
Crosley Corporation,
illustrated
must be obtained
this warranty.
Obligations
without
Crosley Corporation
is warranted
by Crosley Canada Corp. Crosley Corporation
service company.
Product
at the addresses
or phone
by Crosley Corporation.
authorizes
for service and parts under this warranty
Crosley Canada Corp, or an authorized
INFORMATION
by contacting
in the USA and Canada. In the USA, your appliance
is warranted
are subject to change
FOR WARRANTY
slip, or some other appropriate
payment record to establish the warranty period
If service is performed,
it is in your best interest to obtain and keep all receipts.
no person to change
must be performed
features
or specifications
or add to
by
as described
or
notice.
CONTACT:
FOR PRODUCT INFORMATION
CONTACT:
336.761.1212
USA
Canada
800.944.9044
800.265.8352
Crosley Corporation
111 Cloverleaf Dr.
www.crosley.com
12
Winston-Salem,
NC 27103
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising