- Industrial & lab equipment
- Electrical equipment & supplies
- Power conditioning
- Uninterruptible power supplies (UPSs)
- Uninterruptible Power System
- 400
- User manual
advertisement
U P S
Uninterruptible Power System
UPS-200/250/400
USER MANUAL
66P-S025-036
TABEL OF CONTENTS
1.IMPORTANT SAFETY INSTRUCTIONS … … … … … … … … … … … … . . 1
2.INTRODUCTION … … … … … … … … … … . . … … … … … … … … … … … … … . 5
2.1 SYSTEM DESCRIPTION … … … … … … … … … … … … … . … … … . … … … 5
2.2 FEATURES … … … … … … … … … … … … … … … … … … .. … … … … … … … 5
2.3 OUTLOODING … … … … … … … … … … ... … … … … … … … … … … … … … 6
3.INSTALLATION AND OPERATION … … … … … … … … … … … … … … … . . 7
3.1 SITE SELECTION … … … … … … … … … … … … … … … … … … … … … … . 7
3.2 UNPACKING … … … … … … … … … … … … … … … … … … . . … … … … … … 7
3.3 CONNECTING THE UPS … … … … … … … … … … … … … . … … … … … … 7
3.4 SARTING OPERATION … … … … … … … … … … … … … … … … … … … … 8
3.5 BACK UP OPERATION … … … … … … … … … … … … … .. … … … … … … . . 8
4.MAINTENANCE … … … … … … … … … … … … … … … … … … … … … … . . … 9
5.TROUBLESHOOTING … … … … … … … … … … … … … … … … … … … … … … 9
6.BATTERY REPLACEMENT … … … … … … … … … ... … … … … … … … . … … 1 0
7.STORAGE … … … … … … … … … … … … … … … … … … … … … … … … … … … 1 1
8.SPECIFICATIONS… … … … … … … … … … … … … … … … … … … … … … . . … 12
2
1. IMPORTANT SAFETY INSTRUCTIONS,
SAVE THESE INSTRUCTIONS
1.1
• This manual contains important instructions for Model UPS series that should be followed during installation and maintenance of the UPS.
• Unplug the unit from the AC outlet and make certain of all switches are in the “off” position before cleaning. Do not use liquid or aerosol cleaners, use only a water dampened cloth for cleaning.
• Do not attempt to service this product by yourself. Opening or removing covers may expose you to dangerous voltage. Return the unit to your dealer for proper handling.
• The output receptacles may have high voltage even the unit is not connected to wall power.
• If the fuse is opened, to reduce the risk of fire, replace only with the same type and rating of fuse.
• Servicing of battery should be performed by personnel knowledgeable of battery and the required precautions. Keep unauthorized personnel away from battery.
3
1.2 SAFETY
CAUTION:
l This unit is should be installed from service personnel.
l The equipment can be operated by any individuals with no previous experience.
l The socket-outlet shall be installed near the equipment and easily accessible.
l Attention, hazardous through electric shock. Also with disconnection of this unit from the main, hazardous voltage still may be accessible through supply from battery. The battery supply should be therefore disconnected in the plus and minus pole through the from the outer enclosure accessible battery fuses when maintenance of service work inside the UPS is considered.
2. INTRODUCTION
4
2.1 SYSTEM DESCRIPTION:
This unit is a stand by uninterruptable power supply (UPS.), it can keep computers or other critical equipments performing through power disturbances and outages.
2.2 FEATURES:
• Utilizes microprocessor based controls, minimizes the dependency on hardware, maximizes system flexibility and assures super reliability.
• Extremely compact in size, suitable for any available space.
• Unit can be TURNED ON any time with or without utility power.
Suitable for emergency applications, especially during utility power failure.
• Automatic frequency selection to mate with utility power.
•Two-Step battery charger (first with cyclic charging voltage; second with stand by charge voltage) to prolong battery life and fully charge the battery.
• With actually overload protection both in line and battery mode.
2.3 OUTLOOKING
OVER LOAD
LINE NORMAL
BAT. IN USE
MODEL-UPS-250
2
5
1
UPS-200/250/400 Front Side View UPS-200/250/400 Rear Side View
1 BRAND NAME 2 POWER SWITCH
3 OUTLET SOCKET
4 INLET SOCKET
3 INSTALLATION AND OPERATION
3.1 SITE SELECTION
6
This unit can be installed besides the computer or equipment, do not install it in non-ventilated areas.
3.2 Unpacking
The following items are included in the carton l User’s manual.
l Power cord.
l UPS
3.3 Connecting the UPS
For UPS series: Use the power cord to connect the wall power (utility power) and inlet socket. Connecting the power cord of your computer to the UPS output receptacle.
3.4 Staring operation
3.4.1 Turn on the UPS by pressing switch on rear panel to “ON” position, the
LED will light up, if the line voltage is absent, the LED will be slowly
7
The LED and buzzer will be slowly flash and beeping. The computer or other equipment shall still work well, without any malfunctions or reset action.
3.4.4 Reapply the line power to the UPS, the UPS shall return to line mode in 2 seconds.
3.4.5 Keep line power applied continuously to the unit for at least 5 hours to ensure battery is fully charged.
3.5 Backup operation
If the line power is outage or input voltage is too high or too low, the UPS will transfer to battery mode. The back up time should be about 10 minutes for one set computer, if the back up time is less than 3 minutes, and the UPS have been long time charged, the battery is not good enough and better to replace with a new one.
flash and buzzer will be slowly beeping.
3.4.2 Turn on the computer, if it is over loaded, the LED and buzzer will rapidly flash and beep, you should check the power rating of the loaded equipment then remove the less critical one. Generally, the total power consumption of one set of personal computer (color monitor) will not exceed the rating of this UPS.
3.4.3 Unplug the input power cord to test the UPS backup function.
4 MAINTENANCE
The unit is designed for years of trouble-free operation, so only a little maintenance is required.
8
A few helpful hints:
-Periodically vacuum dust from ventilation openings.
-Occasionally wipe exterior with a damp cloth.
5 TROUBLESHOOTING
If the UPS fails to operate properly, please check the following
TROUBLESHOOGING CHART. If the unit is to be returned for service, please note the following information and pack it in the original carton .
a. model number, serial number.
b. Date of purchase.
c. Full description of problem.
TROUBLE SHOOGING CHART
PROBLEM
UPS not on
LED not light
POSSIBLE CAUSE main switch not on battery failure battery voltage less than 10V
PC board failure
ACTION TO TAKE turn on the main switch replace or recharge the battery call for service replace the PC board, call for service replug the power cord.
UPS always at battery mode power cord lose
AC fuse burn out
Line voltage too high, too low or black out
PC board failure replace the AC fuse normal condition replace PC board, call for service
Back up time too short
LED rapidly blinking
Buzzer rapidly beeping battery not fully charged
PCB failure over load recharge the UPS at least 4 hr.
replace the PC board, call for service remove the least critical load
6 BATTERY REPLACEMENT
Your battery should run any where from 3-5 years before eve needing to be replaced.
Please follow the instructions below for easy battery replacement.
9
1) Unplug unit from AC power source and disconnect all connected equipment.
2) Disconnect AC power cord from unit.
3) Turn unit upside down and using a phillips screws driver, unscrew the 4 screws holding the top of the unit to bottom. Put screws in a safe place for reconnection.
4) Holding the top together firmly with the bottom, turn the entire unit right side up.
5) Carefully lift top cover off and place to the side. The connecting wires and electronics will be exposed. Be careful not to touch any inner components when changing the battery.
6) Remove the 2 connecting wires from the battery.
7) You can now easily remove the battery from the unit
CAUTION: Do not dispose of battery in fire.
CAUTION: Do not attempt to open the battery.
CAUTION: The following precautions should be taken when replacing the battery l Remove watches, rings, etc …..
l Use tools with insulated handles
8) Place your new battery in the same position/direction and reconnect the wires red wire-position(+) and black wire negative(-)
9) Please follow steps 5.4 and 3 (in that order) to reconnect the entire unit.
10)Please follow manual instructions in order to properly reconnect your equipment.
7 STORAGE
7.1 Storage conditions
Store the UPS covered and upright in a cool, dry location, with its battery fully
10
charged. Before storing, charger the UPS for at least 4 hours. Remove any accessories in the accessory slot and disconnect any cables connected to the computer interface port to avoid unnecessary draining the battery.
7.2 Extended storage
During extended storage in environments where the ambient temperature is –15 to +30℃(+5 to +86℉),charge the UPS’s battery every 6 months.
During extended storage in environments where the ambient temperature is +30 to +48℃(+86 to +118.4℉), charge the UPS’s battery every 3 months.
MODEL
INPUT
OUTPUT
8.
SPECIFICATIONS
Capacity
Voltage
Frequency
UPS200
200VA
100V,115V,230V
UPS-250
250VA
50 or 60 Hz +/-5% (auto sensing)
UPS-400
400VA
Voltage (on battery) Simulated sine wave at Line Input +/-5%
11
PROTECTION and FILTERING
BATTERY
PHYSICAL
INDICATOR
ALARM
CONFORMANCE
ENVIRONMENT
Frequency
(on battery)
Transfer Time
Spike Protection
Overload Protection
50 or 60 Hz +/-2%
Unit Input
Short Circuit
Type
Fuse for overload & short circuit protection
UPS output cut off immediately or input fuse protection
Sealed, maintenance-free lead acid
Typical Recharge Time 4 hours ( to 90% of full capacity)
Back up Time 3-30 minutes (depending on computer load)
Net Weight kg (lbs) 5.0 (11)
5.5 (12) Shipping Weight kg
(lbs)
Dimension (mm)
WxDxH
97 x 260 x 135
5.5 (12)
6.0 (13)
6.0 (13)
6.5 (14)
Input Inlet
Line normal
Battery in use
Battery low
IEC 320 power inlet
Steady ON of green LED
Slow blinking of green LED (about 0.47Hz)
Fast blinking of green LED (about 1.825 Hz)
Over low
2/4 milliseconds, including detection time
320 joules, 2ms
UPS automatic shutdown if overload exceeds 110% of nominal at 60 seconds and 130% at 3 seconds.
Battery in use
Battery low
Over load
Safety
Surge
Ambient operation
Audible noise
Storage condition
Very rapid blinking of green LED (about 3.75 Hz) between 110% to 130% load.
Slow beeping sound (about 0.74 Hz ) 1 minute
Medium beeping sound (about 1.825Hz)
Rapid beeping sound (about 3.75 Hz) within 110% to130% load.
cUL, TUV, CE, meet FCC
Meet IEEE 587 standard
3,500 meters max. elevation, 0-95% humidity noncondensing 0-48 deg C
<40 dBA (1 meter from surface )
15000 meters max. elevation
©1999 Powercom Co., Ltd. All right Reserved. All trademarks are property of their respective owners.
Specifications subject to change without notice.
12
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project