Mitsubishi Electric WD-82737 Owner's Guide

Add to my manuals
88 Pages

advertisement

Mitsubishi Electric WD-82737 Owner's Guide | Manualzz

HOME THEATER TELEVISION

MODELS

C9 Series

737 Series

837 Series

OWNER’S GUIDE

Guidelines for setting up and using your new widescreen TV start on page 7.

-

-

For questions:

Visit our website at www.mitsubishi-tv.com.

E-mail us at [email protected].

Call Consumer Relations at 800-332-2119.

For information on System Reset, please see the back cover.

To order replacement or additional remote controls or lamp cartridges, visit our website at www.mitsuparts.com or call 800-553-7278.

837 Series.

IR emitter cables for NetCommand home-theater control are available for purchase from Mitsubishi. Call 800-553-7278 and request either part number 242D483020

(two-ended cable) or part number 299P254020 (four-ended cable).

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: This product shall be connected to a

MAINS socket outlet with a protective earthing connection.

MAINS DISCONNECTION: The mains plug is used as the disconnect device. The disconnect device shall remain readily operable.

Stand Requirement

CAUTION: Use these Mitsubishi TV models only with the Mitsubishi stand models shown here. Other stands can result in instability and possibly cause injury.

Stand Model TV Model

WD-60C9, WD-65C9

WD-60737, WD-65737

WD-65837

MB-S60/65A

WD-73C9

WD-73737

WD-73837

MB-S73A

82-inch TVs: Mitsubishi does not design, manufacture, or sell matching bases for 82-inch televisions

(WD-82737, WD-82837). When selecting a stand, base, or other furniture to support the TV, please make sure it is designed with the appropriate dimensions for stability and to support the TV’s total weight as well as the weight of any additional equipment you plan to store.

TV WEIGHT: This TV is heavy. Exercise extreme care when lifting or moving it. Lift or move the TV with a minimum of two adults. To prevent damage to the TV, avoid jarring or moving it while it is turned on. Always power off your TV, unplug the power cord, and disconnect all cables before moving it.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

FCC Declaration of Conformity

Product:

Models:

Projection Television Receiver

WD-60C9, WD-65C9, WD-73C9

WD-60737, WD-65737, WD-73737,

WD-82737

WD-65837, WD-73837, WD-82837

Responsible

Party:

Mitsubishi Digital Electronics

America, Inc.

9351 Jeronimo Road

Irvine, CA 92618-1904

Telephone: (800) 332-2119

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-

-

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

-

-

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/

TV technician for help.

Changes or modifications not expressly approved by Mitsubishi could cause harmful interference and would void the user’s authority to operate this equipment.

WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.

Note: Features and specifications described in this owner’s guide are subject to change without notice.

Contents

Important Information About Your TV

Installation and Operating Notes . . . . . . . . . . . . .

4

Important Safety Instructions . . . . . . . . . . . . . . . .

5

Special Features of Your TV . . . . . . . . . . . . . . . . .

6

1 Basic Setup and Operation

Package Contents . . . . . . . . . . . . . . . . . . . . . . .

7

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . .

7

First-Time Power-On . . . . . . . . . . . . . . . . . . . . . .

7

TV Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8

Setting Up TV Inputs . . . . . . . . . . . . . . . . . . . . .

10

Basic TV Operation . . . . . . . . . . . . . . . . . . . . . .

12

2 TV Connections

Before You Begin . . . . . . . . . . . . . . . . . . . . . . .

14

Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . .

15

Y Pb Pr Component Video Device . . . . . . . . . . .

17

HDMI Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17

DVI Video Device . . . . . . . . . . . . . . . . . . . . . . .

18

Composite Video Device . . . . . . . . . . . . . . . . . .

18

Antenna or Cable TV Service . . . . . . . . . . . . . . .

18

VCR or DVD Recorder to an Antenna or

Wall Outlet Cable . . . . . . . . . . . . . . . . . . . . . .

19

VCR or DVD Recorder to a Cable Box . . . . . . . .

19

A/V Receiver . . . . . . . . . . . . . . . . . . . . . . . . . .

20

A/V Receiver with HDMI Output . . . . . . . . . . . . .

20

3 Using TV Features

Selecting an Input . . . . . . . . . . . . . . . . . . . . . .

21

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .

21

ChannelView Channel Listings . . . . . . . . . . . . . .

22

Redirecting Audio Output . . . . . . . . . . . . . . . . .

22

Controlling A/V Receiver Sound Volume . . . . . . .

22

Status Display . . . . . . . . . . . . . . . . . . . . . . . . .

23

TV Signals and Display Formats . . . . . . . . . . . . .

24

3D Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25

Using the TV with a Personal Computer . . . . . . .

26

Camera Images and Music Files . . . . . . . . . . . .

28

Introduction to Home-Theater Control . . . . . . . .

31

4 TV Menus

Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32

Menu Navigation . . . . . . . . . . . . . . . . . . . . . . .

32

Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33

Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37

Initial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

38

Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40

Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

42

5 NetCommand IR Control

About NetCommand IR Control . . . . . . . . . . . . .

45

IR Emitter Placement . . . . . . . . . . . . . . . . . . . .

46

Initial NetCommand Setup . . . . . . . . . . . . . . . .

47

Operating NetCommand-Controlled Devices . . .

48

6 NetCommand IR Control of an A/V Receiver

Controlling an A/V Receiver after NetCommand

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

51

Setting Up A/V Receiver Control

Power and Volume . . . . . . . . . . . . . . . . . . .

52

Automatic Audio or Audio/Video Switching . .

53

Appendices

Appendix A: Programming the Remote Control .

58

Appendix B: Bypassing the Parental Lock . . . . .

65

Appendix C: HDMI Control of CEC Devices . . . .

67

Appendix D: TV Care

Lamp-Cartridge Replacement and Cleaning .

70

Cleaning Recommendations . . . . . . . . . . . .

72

Care of the Remote Control . . . . . . . . . . . . .

72

Appendix E: Troubleshooting . . . . . . . . . . . . . .

73

Trademark and License Information . . . . . . . . . .

80

Mitsubishi TV Software

. . . . . . . . . . . . . . . . . . . .

81

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84

Index

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

86

4

Important Information About Your TV

For Your Records

Record the model number, serial number, and purchase date of your TV. The model and serial numbers are on the back of the TV. Refer to this page when requesting assistance with the TV.

MODEL NUMBER

SERIAL NUMBER

PURCHASE DATE

RETAILER NAME

LOCATION

Installation and Operating Notes

Custom cabinet installation must allow for proper air circulation around the television.

NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER

IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S

ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PRO-

VIDES GUIDELINES FOR THE PROPER GROUNDING AND,

IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND

SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF

THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY

AS PRACTICAL.

Internal Fans

Internal cooling fans maintain proper operating temperatures inside the TV. It is normal to hear the fans when you first turn on the TV, during quiet scenes while viewing the TV, and for a short time after shutting off the TV. You may notice louder fan noise about 30 seconds after shutting off the TV and while using the

Bright Lamp Mode.

Lamp Replacement

For lamp-replacement instructions, see Appendix D.

To Order a Replacement Lamp Under Warranty

Call (800) 553-7278. Please have model number, serial number, and TV purchase date available.

Important: All lamps replaced under warranty must be returned to Mitsubishi where they will be inspected for defect verification.

To Purchase a Replacement Lamp After Warranty

Visit our website at www.mitsuparts.com or call (800)

553-7278. Order new lamp part number 915B403001

TV Software

Do not attempt to update the software of this TV with software or USB drives not provided by or authorized by Mitsubishi Digital Electronics America, Inc. Nonauthorized software may damage the TV and will not be covered by the warranty.

Important Safety Instructions

Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

E XAMP LE OF ANT E NNA G R OUNDING

G R OUND C LAMP

E LE C T R IC

S E R V IC E

E QUIP ME NT

NE C — NAT IONAL E LE C T R IC AL C ODE

ANT E NNA

LE AD IN WIR E

ANT E NNA

DIS C HAR G E UNIT

(NE C AR T IC LE 810-20)

G R OUNDING

C ONDUC T OR S

(NE C AR T IC LE 810-21)

G R OUND C LAMP S

P OWE R S E R V IC E G R OUNDING

E LE C T R ODE S Y S T E M

(NE C AR T 250, P AR T H)

Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.

Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

5

6

Special Features of Your TV

Your new high-definition widescreen television has many special features that make it the perfect center of your home entertainment system, including:

1080p High-Definition DLP Display System

Your Mitsubishi HDTV uses Texas Instruments Digital

Light Processing™ technology for rear-projection TVs to create the picture you see on screen. All images are displayed at 1080p. The TV uses Plush 1080p® 5G to convert lower-resolution signals to 1080p for display.

The TV can also accept 1080p original signals and maintain them at 1080p through all processing until displayed.

3D Ready

All Mitsubishi 1080p DLP HDTV’s are 3D Ready. This feature lets you experience the new 3D technologies applied to many recent movies and video games.

Immerse yourself in your favorite video game, movie, or sporting event displayed in 3D.

16:9 Widescreen Picture Format

Enjoy a full theatrical experience in the comfort of your home. View pictures as film directors intended them.

Digital TV broadcasts, DVDs and newer video game consoles support this widescreen format.

Integrated HDTV Tuner

Your widescreen Mitsubishi HDTV has an internal HDTV tuner able to receive both over-the-air HDTV broadcasts (received via an antenna) and non-scrambled digital cable broadcasts, including non-scrambled

HDTV cable programming.

High-Definition Video Inputs

Component Video Inputs.

Also called Y/Pb/Pr inputs, these inputs receive standard analog video formats of 480i, 480p, 720p, and 1080i high-definition signals. This provides a high level of flexibility when connecting DVD players/recorders, cable boxes, and satellite receivers.

HDMI Inputs.

These inputs accept digital 480i,

480p, 720p, 1080i, and 1080p video signals plus

PCM digital stereo signals. The HDMI™ inputs can also accept a variety of PC signals and resolutions.

These inputs support HDMI 1.3 Deep Color (up to

36 bits) and the x.v.Color extended color gamut.

Used with an adapter, these HDMI inputs also accept compatible digital DVI video signals. HDMI inputs provide additional high-performance, high-definition connections for maximum flexibility in your choice of home theater products. The HDMI inputs are HDCP copy-protection compatible.

Easy Connect Auto Input Sensing

Easy Connect™ Auto Input Sensing automatically recognizes when you plug in a device and prompts you to assign a name to it. The TV ignores any unused inputs, so the result is an uncluttered menu where you can easily find and select connected devices by name.

Home-Theater Control

HDMI Control

Available for all models. HDMI devices with Consumer Electronics Control (CEC) capabilities may be compatible with the TV’s HDMI Control feature. Compatible devices can receive control signals through the

HDMI connection, allowing the TV’s remote control to operate some functions of these devices.

NetCommand with IR Learning

837 Series. Your Mitsubishi HDTV offers a new level of networking that seamlessly integrates selected older A/V products with new and future digital products. NetCommand ® supports IR (infrared) control of products such as VCRs, DVD players, cable boxes, and satellite receivers. NetCommand can “learn” remote control signals directly from many devices, allowing you to create a customized NetCommand-controlled hometheater system. The necessary IR emitter cables are available for purchase separately from Mitsubishi.

ENERGY STAR

®

This is an ENERGY STAR

®

qualified TV. Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency guidelines set by the U.S. Environmental Protection Agency and the

U.S. Department of Energy.

1.

1

ACTIVITY

GUIDE MENU INFO BACK

1

Basic Setup and Operation

Package Contents

Before You Begin

Please take a moment to review the following list of items to ensure that you have received everything.

1.

Review the important safety, installation, and operating information at the beginning of this book.

2.

1. Remote Control

Choose a location for your TV.

2. Two AA Batteries

• Allow at least four inches of space on all sides of the TV to help prevent overheating. Overheating may cause premature failure of the TV as well as shortened lamp life.

3. Basic Owner’s Guide

4. HDTV Quick-Setup Guide

5. Product Registration Card

• Avoid locations where light may reflect off the screen.

• See the stand requirements on page 2.

3

3.

4. 5

Install the batteries in the remote control.

Plug the TV into an AC power outlet.

4

First-Time Power-On

AA

AA

2

Remote Control Batteries

Remove the remote control back cover.

1.

2.

Confirm that the remote control is in TV mode.

• Press the side button

• once to light the mode indicator and confirm that TV mode is active.

To change, press the side button additional times to activate TV mode.

Aim the remote control at the TV and press the

POWER key

. Wait for the

Welcome screen.

GUIDE MENU INFO BACK

BACK

TV

GUIDE MENU INFO

Emitter bulb

2. Load the batteries, making sure the polarities

(+) and (-) are correct. Insert the negative (-) end first.

3.

Press if you wish to change the menu language to Español.

7

4.

Press to highlight EXIT .

Press ENTER to clear the menu.

3. Slide the cover back into place.

8

1. Basic Setup and Operation

TV Controls

Remote Control

ACTIVITY Press to select a TV activity and input. See page 21.

GUIDE ChannelView listings, page 22.

MENU TV main menu, page 32

INFO TV status (page 23) or TV help.

VOLUME UP

MUTE

VOLUME DOWN

Record/Playback controls for external devices

When remote control is programmed, page 58

HDMI control, page 69

837 Series: NetCommand, page 48

(PAUSE) Freezes a broadcast TV picture.

Number/letter keys

Channel tuning, page 12

Clears some menu entries.

ACTIVITY

GUIDE MENU INFO BACK

VCR CABL/SAT TV DVD AUDIO

Control-mode indicator for device type to control. Use the side button to change.

Powers TV on or off.

Side button sets the control mode for the type of device to operate. Set mode to TV for normal TV viewing.

CHANNEL UP

LAST. Goes to the previously tuned channel.

CHANNEL DOWN

PAGE UP

ENTER

Selects a channel number or menu item.

Navigation controls

PAGE DOWN

MORE

Displays a menu showing additional functions for the number keys.

For the MORE menu in TV mode, see below.

With remote control programmed for other device types, page 58.

The MORE menu in other modes is specific to the device type.

For CEC-enabled devices, page 67

The MORE menu in TV mode

Note: To operate other audio/video devices using the TV’s remote control:

• See Appendix A, “Programming the Remote

Control.”

• For HDMI devices compatible with the TV’s

HDMI Control feature, see Appendix C.

• 837 Series

See page 45 for NetCommand IR “Learn-

ing” of device keys.

For use of specific keys with NetCommand-controlled devices, see “Special

Operation Methods,” page 48.

CC Closed captions, page 37

VIDEO Video adjustments, page 35

AUDIO Audio adjustments, page 36

SLEEP Sleep Timer, page 21

FORMAT Picture shape (aspect ratio), page 24

MORE Clears the MORE menu.

1. Basic Setup and Operation

9

TV Controls, continued

TV Control Panel

Buttons on the control panel duplicate some keys on the remote control.

• Refer to upper labels when no TV menus are displayed.

• Refer to lower labels when using TV menus or after activating a special function.

737 and C9 series.

Flip open cover to use buttons on the front panel.

STATUS

POWER

System Reset

If the TV fails to respond to the remote control, the control-panel buttons, or will not power on/off, perform

System Reset. Recent setting changes made before using System Reset may be lost.

To perform System Reset, press and hold the POWER button on the control panel for ten seconds.

Panel-Lock Release

To release the Panel Lock using the TV control panel, press and hold the ACTIVITY button on the control panel for ten seconds. If the TV is off, press the POWER button to have it power on.

To activate the Panel Lock, use the Lock menu, page 44.

If You Power Off the TV by Mistake

1. Press POWER again, within about 60 seconds, to have the TV come back on immediately.

2. If the status indicator starts rapidly blinking green (about 60 seconds after you shut off power), wait a few moments for the status indicator to stop blinking and press POWER to turn the TV on again.

Controls on 737 and C9 series TVs. 837 series controls are similar and are located next to the STATUS indicator.

STATUS Light

Key Off Steady On Slow Blinking Fast Blinking

LED Color TV Condition

None

TV is powered off. Normal operation.

Green

TV is powered on. Normal operation.

Green

Green

Yellow

TV powered off, auto-on TV Timer is set.

Normal operation. TV can be turned on at any time.

TV just powered off and lamp is cooling.

Sixty seconds after turning off TV, LED will start to blink. TV can be turned back on before blinking starts or after blinking stops, but not while the indicator is blinking. Normal operation.

TV is too hot. The TV will display a warning message and shut off if it overheats.

Yellow

Red

• Ambient room temperature may be too high. Turn off the TV and let the room temperature drop.

• Clear blocked air vents. Ensure at least a four-inch clearance on all sides of the TV.

• Clean the lamp-cartridge air filter. See “Lamp-Cartridge Filter Cleaning,” page 71.

Lamp access door is not secure or no lamp installed.

TV will not operate until lamp access door is secured. See Appendix D.

Lamp failure. Replace the lamp. See Appendix D.

Red

TV may require service.

Turn off the TV and unplug the set from the AC power source. Wait one minute and then plug the set back in.

If the red LED is still on, contact your dealer or a Mitsubishi Authorized Service Center. Go to www.mitsubishi-tv.com or call 1-800-332-2119 to receive Authorized Service Center information.

10

1. Basic Setup and Operation

Setting Up TV Inputs

Using the ANT (Antenna) Input

If using an antenna or direct cable service (no cable box), connect the incoming coaxial cable to the TV’s

ANT input. Refer to page 18.

You must save channels to memory with a channel scan to enable reception of all available high-definition and standard-definition digital channels. The channel scan will search for channels available locally. If you skip this step, the TV will receive only analog channels.

Memorizing Channels with Channel Scan

For the ANT input

To start channel memorization

1.

2.

Power on the TV.

Press MENU and open the Initial > Channel menu.

Setting Up Other Inputs

1.

2.

3.

4.

Connect your devices to the TV, making note of which TV input jack is used for each device. See

“TV Connections,” page 14, for recommendations.

Power on the devices to ensure detection.

Power on the TV.

The TV will display the New Device Found screen for each new connection it detects Learn more about Auto Input/Auto Output Sensing on the opposite page.

Select the device type if the device is not recognized automatically.

Start channel memorization from the Initial > Channel menu.

3.

4.

Press ENTER to enter the menu.

Select Ant Air if connected to an over-the-air antenna. Select Ant

Cable for direct cable.

5.

Highlight Scan and press ENTER.

Channel memorization may take up to 15 minutes to complete.

To stop channel memorization before completion,

press CANCEL.

Use the Initial > Channel > Edit menu (page 39) for additional channel options, such as adding or deleting channels from memory.

Sample New Device

Found screen.

Important Note for NetCommand IR Users

837 Series. Be sure to select the correct device type here. Although you can change the device type later in the Inputs > Name menu, any “learned” Net-

Command IR codes will be erased when you make the change.

5.

6.

837 Series. You can perform NetCommand IR

“learning” after selecting the device type or at a later time when convenient. To perform now, highlight NetCommand and press ENTER. See “Initial

NetCommand Setup,” page 47 or “Setting Up A/V

Receiver Control,” page 52.

Press BACK to close the New Device Found screen.

The TV will then display the New Device Found screen for the next connection it finds.

Setting Up TV Inputs, continued

About Auto Input Sensing/

Auto Output Sensing

This TV’s Easy Connect™ Auto Input Sensing feature detects most connections automatically.

Auto Input/Auto Output Sensing for Most Devices

When you first connect a device, the TV will: a. Detect the connected device and automatically switch to it.

b. Prompt you to identify the device type.

c. 837 Series. Prompt you to perform NetCommand set-up for the device, if available.

d. Repeat these steps for other newly detected devices.

Which Jacks Trigger Auto Sensing?

TV Jacks and

Auto Sensing

Y/VIDEO (detected as composite video)

Y/VIDEO plus Pb (detected as component video)

HDMI

USB (837 series) 

DIGITAL AUDIO OUTPUT

(orange jack)

AVR AUDIO OUTPUT

(red jack)

ANT (Antenna) 

IR NetCommand Output

(837 series)

The TV may not detect an HDMI device when the device is powered off. Detection will occur when the device is next powered on.

When You First Connect a Device

Most Device Types.

Select the device type from the on-screen list. The device type you select here will appear as a device icon in the Activity menu.

A/V Receiver

The TV can detect audio connections on the

DIGITAL AUDIO OUTPUT jack and the right (red)

AVR AUDIO OUTPUT jack.

1. Basic Setup and Operation

New Device Found screen for a device with HDMI control enabled. Select On to enable the TV’s CEC control of the device. In some cases, as in the example above, you will also be prompted to select a device name.

Tips on Auto Sensing

Choose a different name for each input.

The antenna input ( ANT) is never detected, although you can turn off the unused antenna input in the Inputs > Name menu.

Change the device type displayed in the

40).

Activity menu by using the Inputs > Name menu (page

837 series.

Any “learned” NetCommand IR codes will be erased if you change the device type in the Inputs > Name menu.

Reactivating Auto Input Sensing for an HDMI Input

When you disconnect an HDMI device, Auto Input

Sensing is disabled until you perform these steps.

1.

2.

3.

Disconnect the HDMI device.

Delete the removed HDMI device in the Inputs >

Name menu (see “Removing an HDMI Device,” page 69).

Connect the new device and the New Device

Found screen will display.

11

For an HDMI A/V receiver, select AVR from the list of device types if the A/V receiver is not recognized automatically.

HDMI CEC Devices Compatible with the TV’s

HDMI Control Feature. Compatible CECenabled HDMI devices are often recognized automatically by the TV. HDMI Control may allow you to control some functions of a CEC-enabled device.

See Appendix C, “HDMI Control of CEC Devices.”

12

1. Basic Setup and Operation

Basic TV Operation

Selecting an Input to Watch

1.

2.

3.

Press ACTIVITY.

Press and to highlight an input.

Press ENTER to switch to the input.

Watching Broadcast TV

TV Connected to an Antenna, Direct Cable, Cable

Box, Set-Top Box, or Satellite Receiver

1. Select an input to watch from the Activity menu’s

Watch TV group.

Note: For more about the Activity menu, see page 21.

Watching DVDs or Videos

TV Connected to a DVD Player, DVR, or VCR

Press ACTIVITY and select a movie source from the

Activity menu. If you named devices during Auto Input

Sensing, select the input from the Watch Movie group.

Activity menu, DVD input selected

Activity menu, antenna input selected

2.

Tune to a channel on the ANT input using any of these methods.

Enter the channel number using the number keys on the remote control and press ENTER.

For a two-part digital channel, such as 3-1, press 3 CANCEL 1 to enter a dash (separator).

Press CHANNEL UP /CHANNEL DN (+/) to change channels one channel at a time.

Press (LAST) to switch back to the previously tuned channel.

• Antenna or Direct Cable Only.

Press GUIDE to display ChannelView channel listings, highlight a channel number, and press ENTER to tune.

TV Tips

Turning the TV On or Off

Point the remote control at the front of the TV and press the POWER button.

Press the POWER button on the TV control panel.

If You Turn Off the TV by Mistake

Press POWER again, within about 60 seconds, to have the TV come back on immediately.

If the status indicator starts rapidly blinking green (about 60 seconds after you shut off power), wait a few moments for the status indicator to stop blinking and press POWER to turn the TV on again.

Controlling Sound Volume

Press VOLUME UP/VOLUME DN to adjust the sound level.

See also “Controlling A/V Receiver Sound

Volume” on page 22.

Basic TV Operation, continued

Making Picture Adjustments

1.

To get the best picture under different viewing conditions, set the Picture Mode before changing other video settings. See page 35 for more.

a. Press MENU and go to the Adjust > Picture >

Picture Mode menu.

b. Make one of these selections:

Name When to Use

Brilliant Under bright light

Game With gaming consoles

Bright For most daytime viewing

Natural For most nighttime viewing

c. Press MENU to clear the menu.

2.

3.

4.

5.

Press MORE.

Press 8 (VIDEO).

Press to display the name of the adjustment you want.

Press to make the adjustment.

Additional picture adjustments are described on pages

33 and 34.

1. Basic Setup and Operation

13

Other TV Features

Activate Audio Lock to control your sound system with the TV’s remote control left in TV mode. See page 59.

To set the TV Clock see page 38. Set the TV

Clock if you plan to use the TV Timer (page 38) or

ChannelView (page 22) features.

To set parental controls, see the Lock menu, page

42.

To change the input names that appear in the

Activity menu, see Inputs > Name options, page

40.

3D Video.

See page 25.

To program the remote control to operate other

A/V devices, see Appendix A, “Programming the

Remote Control,” page 58.

To control compatible devices using HDMI CEC control, see Appendix C, “HDMI Control of CEC

Devices,” page 67.

837 Series.

To view still and moving digital camera images on the TV, see “Camera Images and Music

Files,” page 28.

837 Series.

To control A/V devices with NetCommand, see chapter 5, “NetCommand IR Control for

Most Devices” on (page 45).

Audio Settings

Changing the Audio Output

To switch audio output from the internal TV speakers to a connected external sound system or headphones:

1.

2.

3.

4.

Press MORE.

Press 9 (AUDIO).

Press until the Speakers option is displayed.

The Speakers option will display only if a connection has been detected on one of the TV’s audio outputs.

Press to switch between TV and either AV

Receiver or Headphones.

Changing Audio Settings

1.

2.

3.

4.

Press MORE.

Press 9 (AUDIO).

Press to display the name of the adjustment you want.

Press to change the setting.

Other Information

TV Care

Lamp Cartridge.

When the lamp cartridge needs replacement, replace the lamp yourself and save

the cost of a service call. See Appendix D for instructions.

General Cleaning.

See “Cleaning Recommendations,” page 72.

Assistance

For troubleshooting, service, and product support, see Appendix E, page 73.

For warranty information, see the TV warranty on page 84.

14

2

TV Connections

Before You Begin

Auto Input Sensing

The TV’s Auto Input Sensing feature automatically recognizes most connections and prompts you to identify the type of device connected. See page 11 for more on

Auto Input Sensing.

Connection Types

Use the connection types available on your input devices that will give the best video quality. For example, choose HDMI over component video, and choose component video over composite video.

Picture Quality

For best picture quality, route signals directly from the input device to the TV whenever possible.

Surround Sound

For best surround sound audio quality, route audiosignal cables or HDMI cables from the source device directly to your A/V receiver or sound system.

IMPORTANT

Accessory items such as cables, adapters, splitters, or combiners required for TV connections are not supplied with the TV.

These items are available at most electronics stores.

Inputs and Outputs

Main Connection Panel

DVI/PC INPUT

(page 18)

6

1

2. TV Connections

15

RS-232C control jack offered on 837 series.

1

ANT

(page 18)

10

RS-232C

HDMI

2 3

AVR

AUDIO

OUTPUT

L

R

Y/ VIDEO Pb Pr

ANT

3D

EMITTER

IRNetCommand

Output

R

5

3D GLASSES

EMITTER

(page 25)

DIGITAL

AUDIO

OUTPUT

R AUDIO L

Y/ VIDEO Pb Pr

(480i / 480p / 720p / 1080i)

2

HDMI

(page 17)

7

AVR

AUDIO

OUTPUT

(page 20)

8

DIGITAL

AUDIO

OUTPUT

(page 20)

4

VIDEO

(composite video, page 19)

3

Y Pb Pr

(component video, page 17)

9

IR

NetCommand Output

(page 46)

Offered on 837 series.

Convenience Inputs

A readily accessible set of jacks is provided for a camcorder, game, or other audio/video device.

837 Series. A fourth HDMI input is provided. If you connect a DVI device to the HDMI input, use the nearby audio jacks to send sound from the device to the TV.

USB port and

HDMI 4 offered on 837 series.

Pr

INPUT 3

Pb Y/ VIDEO L AUDIO R USB HDMI 4

3

11

Y Pb Pr

(component video, page 17)

4

VIDEO

(composite video,

USB

(page 28) page 19)

2

HDMI

(page 17)

Using an Audio-Only Device

Keep an unused RCA-style connector in the Y/VIDEO jack while using an audio-only device such as an MP3 or CD player.

Unused

RCA-style plug

(plug in first)

Y/VIDEO L-AUDIO-R

1.

2.

Audio-only device

SEE DETAIL B

16

2. TV Connections

Inputs and Outputs, continued

1. ANT (Antenna)

Connect your main antenna or direct cable service (no cable box) to ANT. The ANT input can receive digital and analog over-the-air channels from a VHF/UHF antenna or non-scrambled digital/analog cable source.

2. HDMI™ Inputs (High-Definition

Multimedia Interface)

The HDMI inputs support uncompressed standard and high-definition digital video formats and PCM digital stereo audio.

Mitsubishi recommends you use category 2 HDMI

cables, also called high-speed HDMI cables, to connect

HDMI 1.3 source devices. High-speed category 2 cables bring you the full benefits of Deep Color and x.v.Color.

These HDMI inputs can also accept digital DVI video signals. To connect a device’s DVI output to the TV’s

HDMI input, use an HDMI-to-DVI adapter or cable plus analog audio cables. Connect the analog audio cables to the DVI/PC INPUT AUDIO jacks on the TV to receive left and right stereo audio from your DVI device.

Use the HDMI inputs to connect to CEA-861 HDMI compliant devices such as a high-definition receiver or DVD player. These inputs support 480i, 480p, 720p, 1080i, and 1080p video formats.

The TV’s HDMI inputs are compatible with many DVI-D and HDMI computer video signals.

These inputs are HDCP (High-Bandwidth Digital Copy

Protection) compliant.

HDMI Cable Categories

HDMI cables are available as Category 1 and Category 2 types.

Category 2 Cables (also called high-speed

HDMI cables). Newer, HDMI 1.3-compliant DVD players, video games, and set-top boxes require

Category 2 cables, suitable for clock frequencies up to 340 MHz or data rates of up to 10.2 gigabits per second. Use category 2 cables for high-speed 1080p HD signals carrying extended color encodings (i.e., 30 or more bits, also called

Deep Color). Category 2 cables are also suitable for standard HDTV signals.

Category 1 Cables (also called standard HDMI cables). Category 1 cables may be unmarked.

They are suitable for standard HDTV 720p,

1080i, and 1080p signals with 8-bit color depth.

Use category 1 cables for clock frequencies up to 74.25 MHz or data rates of up to 2.23 gigabits per second.

3. Y Pb Pr (Component Video)

Connect devices with component video outputs to this jack. Use the adjacent AUDIO R and L jacks if you wish to send audio to the TV.

4. VIDEO (Composite Video)

Connect a VCR, DVD player, standard satellite receiver, or other A/V device to the TV. Use the adjacent AUDIO

R and L inputs if you wish to send audio to the TV.

5. 3D GLASSES EMITTER

Use this jack for the special IR emitter supplied with 3D glasses. The emitter will send a signal that synchronizes your 3D glasses with the screen display. See page 25

6. DVI/PC INPUT AUDIO

When connecting a DVI device to one of the TV’s HDMI inputs, use these jacks for left and right analog audio.

7. AVR AUDIO OUTPUT

Use AVR AUDIO OUTPUT to send analog audio of the current program to an analog A/V surround sound receiver or stereo system. Digital audio from digital channels and HDMI devices is converted to analog audio by the TV for output on this jack. This is the only audio connection needed to the TV if using an analog

A/V receiver or stereo system.

Headphones. These jacks can also be used for headphones that accept standard line level audio signals.

An adapter may be required.

8. DIGITAL AUDIO OUTPUT

This output sends Dolby Digital or PCM digital audio to your digital A/V surround sound receiver. Incoming analog audio is converted by the TV to PCM digital audio.

If you have a digital A/V receiver, in most cases this is the only audio connection needed between the TV and your

A/V receiver.

9. IR–NetCommand Output

837 Series. Connect IR emitters to this jack to send control signals to external IR remote-controlled devices.

10. RS-232C

837 Series. Use the RS-232C interface to receive control signals from compatible home-theater control devices. See www.mitsubishi-tv.com for a list of control signals for this interface.

11. USB (837 Series)

The TV can read JPEG photo files and mp3 music files from a USB device connected to the USB port.

Y Pb Pr Component Video Device

HDTV Cable Box, Satellite Receiver, DVD/

Blu-ray Player

If your source device has an HDMI output, use the connections for HDMI devices described on this page instead of component video..

Required:

RCA-type component video cables

Left/right analog audio cables.

Note: To hear digital surround sound, connect the digital audio output from the device directly to your digital

A/V receiver.

1

HDMI

2 3

AVR

AUDIO

OUTPUT

R

L

Y/ VIDEO Pb Pr

DIGITAL

OUTPUT

TV main panel

L

Pb Pr

(480i / 480p / 720p / 1080i)

RS-232C

R AUDIO L

ANT

Y/ VIDEO

IRNetCommand

Output

R

Pb Pr

Component video cables

Audio cables

Incoming from cable service or satellite dish

L

AUDIO

R Y

Component video device

Pb Pr

CABLE IN or

SATELLITE IN

2. TV Connections

17

HDMI Device

HDTV Cable Box, Satellite Receiver, DVD/

Blu-ray Player

Required: HDMI-to-HDMI cable.

Connect an HDMI cable from the TV back panel to the

HDMI device output. HDMI devices provide video and audio through the single cable.

Mitsubishi recommends you use category 2 (highspeed) HDMI cables to connect HDMI 1.3 source devices. High-speed category 2 cables bring you the full benefits of Deep Color and x.v.Color. See “HDMI

Cable Categories” on the opposite page for more on

HDMI cable types.

TV main panel

AVR

OUTPUT

L

R

RS-232C

Y/ VIDEO Pb Pr

R AUDIO L

Y/ VIDEO Pb Pr

(480i / 480p / 720p / 1080i) IRNetCommand

Output

R

ANT

HDMI-to-HDMI cable

R

AUDIO

L

Any HDMI device

IMPORTANT

HDMI and Audio Signals

Digital Surround Sound: The TV’s HDMI inputs can receive digital stereo audio signals only. To hear digital surround sound from an HDMI device, connect the device’s HDMI or digital audio output directly to your A/V receiver. See the Owner’s

Guides for those devices for instructions.

18

2. TV Connections

DVI Video Device

Cable Box, Satellite Receiver, DVD Player

Connect DVI devices (digital only) to the TV’s HDMI input jacks.

Required:

Analog stereo audio cables

DVI-to-HDMI cable or DVI/HDMI adapter and HDMI cable

If you are using a DVI/HDMI adapter, it is important to connect the adapter to the DVI device for best performance.

Some devices require connection to an analog input first in order to view on-screen menus and to select DVI as the ouput. Please review your equipment instructions for DVI connectivity and compatibility.

Note: The HDMI connection supports copy protection

(HDCP).

RS-232C

DVI-to-HDMI cable

Audio cables

Antenna or Cable TV Service

Connect the incoming cable to the TV’s ANT input.

ANT

ANT

AVR

OUTPUT

L

R

Y/ VIDEO Pb Pr

Pb Pr

DIGITAL

OUTPUT

R AUDIO L

Y/ VIDEO Pb Pr

(480i / 480p / 720p / 1080i) IRNetCommand

Output

R

TV main panel Pb Pr

(480i / 480p / 720p / 1080i)

RS-232C

IRNetCommand

Output

R

VHF antenna ohm combiner

(side view) or

TV main panel

UHF antenna or

Cable TV service

Older cable box OUT IN

Not recommeded. Other connection types provide better quality audio and video.

DVI OUT R

AUDIO

L Digital DVI device

Composite Video Device

VCR or other device with composite video output

Required:

Composite video cable (usually yellow)

Analog stereo audio cables.

4.

1

TV main panel

HDMI

2 3

L

R

Y/ VIDEO Pb Pr

Y/ VIDEO

RS-232C

R AUDIO L

Pb Pr

(480i / 480p / 720p / 1080i) IRNetCommand

Output

R

ANT

Audio cables

Composite video cable

VCR or other device with composite video output

L R

AUDIO OUT

COMPOSITE

VIDEO OUT

Composite video cable

4.

1

VCR or DVD Recorder to an

Antenna or Wall Outlet Cable

Required:

Two-way RF splitter

Two coaxial cables

Right and left analog audio cables

Component or composite video cables

Note:

• Use composite video only if component video or HDMI are unavailable. For an

HDMI connection between the TV and recorder, see page 17.

• If your recording device has an analog-only tuner, you must use a digital converter box to enable recording of digital broadcasts.

TV main panel

RS-232C

HDMI

2 3

AVR

AUDIO

OUTPUT

L

R

Y/ VIDEO Pb Pr

AUDIO

OUTPUT

R AUDIO L

Pb Pr

(480i / 480p / 720p / 1080i) IRNetCommand

Output

R

Y/ VIDEO Y/ VIDEO Pb Pr

2. TV Connections

19

VCR or DVD Recorder to a Cable Box

Required:

Two-way RF splitter

Three coaxial cables

Right and left audio cables

Composite or component video cables

Video and audio cables required to connect the TV to the cable box.

Notes: Use composite video if only if component video or HDMI are unavailable. For an HDMI connection between the TV and recorder, see page 17.

When using this connection configuration, it is possible to view live cable programs through the recording device. For best picture quality always view live cable programs directly from the TV input connected to the cable box device.

1

TV main panel RS-232C

HDMI

2 3

AVR

OUTPUT

L

R

Y/ VIDEO Pb Pr

AUDIO

OUTPUT

R AUDIO L

Pb Pr

(480i / 480p / 720p / 1080i) IRNetCommand

Output

R

Y/ VIDEO Y/ VIDEO Pb Pr

Audio cables

Composite video cable or

Audio cables

Composite video cable or

Audio and video from cable box directly to TV

Cable

Box

IN

OUT

L R

AUDIO OUT

COMPOSITE

VIDEO OUT

DVD Recorder or VCR

COMPONENT

VIDEO OUT

ANTENNA

IN

L R

AUDIO OUT

COMPOSITE

VIDEO OUT

DVD Recorder or VCR

COMPONENT

VIDEO OUT

ANTENNA

IN

20

2. TV Connections

A/V Receiver

Most setups require either a digital audio cable or analog stereo audio cables. To send audio from TV channels received on the ANT input or devices connected directly to the TV, you must use one of the connections shown below. Usually, only one of these connections is required.

The TV makes all audio available in digital and analog formats:

• Analog audio coming into the TV is available as output in digital stereo format on the DIGITAL

AUDIO OUTPUT jack.

• Digital incoming audio is available as analog output on the AVR AUDIO OUTPUT L and R jacks.

1

AVR

AUDIO

L

OUTPUT

R

TV main panel

RS-232C

ANT

HDMI

2 3

AVR

OUTPUT Y/ VIDEO Pb Pr

DIGITAL

AUDIO

R AUDIO L

Y/ VIDEO Pb Pr

(480i / 480p / 720p / 1080i)

DIGITAL

AUDIO

OUTPUT

Stereo analog cables

(for an analog

A/V receiver)

IRNetCommand

Output

R

Digital coaxial cable

(for a digital A/V receiver)

A/V Receiver with HDMI Output

Required: One HDMI-to-HDMI cable

This option allows you to view content from devices connected to an A/V receiver. The A/V receiver can send audio and video to the TV over a single HDMI cable. You can use an HDMI connection as described here in addition to an audio connection from the TV’s audio output. The optional audio connection allows you to hear, through the A/V receiver, devices connected to the TV only, e.g., an antenna on the ANT input.

You may be able to use the TV’s remote control (in

TV mode) to operate connected CEC-enabled HDMI devices. Experiment with your equipment to determine which functions are available to the TV’s remote control.

See Appendix C, page 67.

837 Series: This setup allows you to use NetCommand-controlled audio and video switching over the

HDMI cable. See “Case 3: Automatic Audio and Video

Switching via HDMI” on page 55.

To use NetCommand to supplement HDMI control of a

CEC-enabled A/V receiver, note the recommendations under “More About Using an HDMI Connection,” page 55.

OPTICAL

INPUT

AUDIO

OUTPUT

TV main panel

Y/ VIDEO Pb Pr

DIGITAL

OUTPUT

R AUDIO L

Y/ VIDEO

AVR

AUDIO

OUTPUT

Pr

L

R

IRNetCommand

Output

R

ANT

AUDIO

OUTPUT

Optional analog or digital audio connection

A/V receiver back panel

Note:

On rare occasions, an HDMI signal may be copy-restricted and cannot be output from the TV as a digital signal. To hear these copyprotected signals through the A/V receiver, use the connection for an analog A/V receiver.

Check the A/V receiver’s Owner’s Guide for information concerning use of the digital input and switching between digital sound and analog stereo sound from the TV.

A/V receiver with HDMI output HDMI OUT L R

High-definition

DVD player

Cable box

VCR

DVD player

3

Using TV Features

Selecting an Input

The Activity menu lets you switch TV inputs. The inputs are organized into groups based on possible ways to use them.

1.

2.

3.

4.

Press the ACTIVITY key.

Use to move through groups of TV inputs.

Use to select an input.

Press ENTER to switch to the input.

To change the list of inputs shown in each activity group, see Inputs > Activity, page 40.

To assign or change the names of input icons, use the

Inputs > Name menu, page 40.

Sleep Timer

The Sleep Timer turns the TV off after the length of time you set.

To set the TV to turn on at a certain time of day, see the Initial > Timer menu on page

38.

Setting the Sleep Timer

1. Press MORE on the remote control. The TV’s MORE menu will display.

2. Press CANCEL (SLEEP) repeatedly to increase the time in 30-minute increments.

The maximum is 120 minutes.

3. Press BACK or wait five seconds without pressing any keys for the message to disappear.

Viewing or Changing the Sleep Timer

1.

2.

3.

Press MORE.

Press CANCEL (SLEEP).

Press CANCEL (SLEEP) additional times to change the number of minutes before the

TV powers off.

SLEEP

With the MORE menu displayed, press the

CANCEL key on the remote control to activate/deactivate the

Sleep feature.

21

22

3. Using TV Features

ChannelView Channel Listings

ChannelView. Programs for the tuned channel are listed on right side of screen.

ChannelView™ shows memorized channels on the ANT input. It displays channel names and program information for digital channels as sent by broadcasters or your local cable service provider (information may be incomplete) . No program information is displayed for analog channels.

Note: You must set the TV Clock (page 38) to receive

ChannelView listings for the current channel.

Using ChannelView

Feature

Receive updates for a digital channel.

See more of the program description for the current channel (if available).

Tune to the highlighted channel.

Instructions

1.

2.

Press to highlight a channel number.

Press the INFO key

(the screen may briefly go blank).

GUIDE Display/hide ChannelView listings from the ANT input.

Scan channels one by one. Hold or

Scan channels quickly.

Hold PAGE UP/PAGE DN

Jump to listings for a specific channel.

1.

2.

INFO

Enter the channel number.

Press ENTER.

ENTER

Redirecting Audio Output

Selecting an Audio Output Device

1.

2.

3.

Press MORE and then 9 (AUDIO).

Press to show the Speakers option. The Speak-

ers option will display only if there is a recognized audio device on an audio or HDMI output.

Press to select either AV Receiver, Head-

phones, or TV.

Disconnecting an Analog A/V Receiver

When you disconnect an analog A/V receiver, change the Speakers setting to TV to hear sound from the TV speakers. Change the setting using the remote control’s MORE > 9 (AUDIO )key or the Adjust > Audio >

Speakers menu.

Controlling A/V Receiver Sound

Volume

Use one of the methods below to control sound volume from an A/V receiver.

With a Standard TV Setup

Recommended Method: Program the TV’s remote control for your A/V receiver and enable the

Audio Lock feature. See page 59.

Program the TV’s remote control for your A/V receiver and set the TV remote control’s mode to

AUDIO. Return the control mode to TV to control the

TV.

Use the remote control that came with the A/V receiver.

With HDMI Control (CEC-Enabled HDMI

A/V Receiver)

The TV’s remote control may control some functions of the A/V receiver. See Appendix C, “HDMI Control of

CEC Devices,” page 67.

With NetCommand IR Control

837 Series. Set up NetCommand control of the A/V receiver’s volume functions in the Inputs > AVR menu.

The TV’s remote will then control A/V receiver volume.

See page 52.

3. Using TV Features

Status Display

Press the INFO key to see the on-screen status display. The most common displays are shown here.

8

1

2

3 4

402-101 KABC

TV-PG DLSV

5

Sleep 30 min

Sample information from the on-screen status display

9

10

Tuesday 9:10 PM

HD 1080i Standard

11

6

Monday Night Football

St. Louis vs. Tampa Bay, played in Tampa for

7

12

Surround

13

English

14

23

ACTIVITY

GUIDE MENU INFO BACK

About Channel Numbers

Channel Numbers for Over-the-Air Reception or

Reception by Direct Cable

Note: All signals are automatically converted to

1080p for display.

Standard-Definition Analog Channels

Cable Reception Channel 3

Cable 3

480i Stretch

Receiving Standard-Definition

Analog Signal (480i)

Standard-Definition Digital Channels

Over-the-Air

Antenna Reception

Main Channel 7

Sub-Channel 1

Ant 7-1 KABC-SD

SD 4:3 Stretch

Receiving Standard-Definition

Digital Signal (SD)

High-Definition Digital Channels

Over-the-Air

Antenna Reception

Main Channel 7

Sub-Channel 1

Ant 7-1 KABC-HD

HD 16:9 Stretch

Receiving High-Definition

Digital Signal (HD)

1. Current Input

2. Audio Indicator. Key:

TV speakers External sound system

Headphones Mute

3. Channel number (antenna source only)

Digital channel includes major and sub-channel numbers.

4. Digital channel name (if broadcast); antenna source only.

5. V-Chip rating

Antenna source only for digital signal

Antenna or VIDEO composite jack for analog signal

6. Program name (if broadcast); digital source only

7. Program description (if broadcast); digital source, antenna only. Press the INFO key additional times to see more of the description.

8. Sleep Timer remaining time

9. Day and time

10. Signal type being received

11. Screen format in use

12. Program Audio indicator (antenna source only)

• Digit al source: Stereo, Surround

• Anal og source: Stereo, Stereo SAP, SAP

13. Available language (digital source, antenna only)

14. Signal-strength indicator (digital source, antenna only)

24

3. Using TV Features

TV Signals and Display Formats

This is a 16:9 widescreen TV suitable for images available from HDTV and many DVDs. You can view older-style, squarish images (4:3 aspect ratio) using one of the display formats described on this page. Press the MORE key and then the

0 key (FORMAT) to cycle through available display formats.

The TV remembers the format you last used for each input.

DVD Image Definitions

Image information may be stated on the DVD case. Some

DVDs support both of the formats described below.

Anamorphic (or Enhanced for WideScreen TV)

Indicates DVDs recorded to show widescreen images properly on 16:9 TV sets using the TV’s Standard format mode

(recommended).

Non-Anamorphic (or 4:3, 1.33:1, Letter Box, or

Full Screen)

Indicates DVDs recorded for viewing on squarish TV screens. They may be full screen (4:3 or 1.33:1) which crops movies to fit the narrow TV, or letter box, which adds black top and bottom bars.

Signal Definitions

480i: Older type of interlaced signals from the ANT input, composite VIDEO, component Y Pb Pr, or HDMI jacks.

480p: Progressive-scan DVD signals on component Y Pb

Pr or HDMI jacks.

720p and 1080i: High-definition signals received through component Y Pb Pr or HDMI jacks. These signals are always 16:9 (widescreen).

1080p: High-definition signals from a PC or Blu-ray player,

HDMI inputs only.

SD 4:3: Standard-definition squarish-screen-format signals from digital channels on the ANT input.

SD 16:9: Standard-definition widescreen-format signals from digital channels on the ANT input.

HD 16:9: High-definition 16:9 widescreen signals from digital channels on the ANT input.

TV Display Format Definitions

Standard: The full-screen format used by HDTV signals.

Use this format to display anamorphic DVDs with a 1.78:1 or

1.85:1 aspect ratio. Anamorphic DVDs with a 2.35:1 aspect ratio are displayed correctly but with top and bottom black bars. Squarish (4:3) images are stretched evenly from side to side. Available for all signals.

Expand: Enlarges the picture to fill the screen by cropping the top and bottom; useful for reducing the letter box top and bottom bars of non-anamorphic DVD images.

Zoom: Enlarges the picture to fill the screen by cropping the sides, top, and bottom to eliminate black bars.

• 480i/480p and SD 4:3 signals: Eliminates top and bottom

• bars on anamorphic DVDs with a 2.35:1 aspect ratio.

720p, 1080i, SD 16:9, and HD signals: Eliminates bars added to squarish 4:3 images.

TV

Original

Signal

Display

Non-anamorphic or SD 4:3 Anamorphic DVD

Standard Distorted.

Not recommended.

Recommended

Expand

Zoom

Stretch

Stretch

Plus

Recommended for letterbox. See

Note 1.

Distorted.

Not recommended. See

Note 1.

Recommended for standard broadcasts.

See Note 1.

Recommended for standard broadcasts.

See Note 1.

Distorted; not recommended.

See Note 1.

Recommended for anamorphic

2.35:1 images.

See Note 1.

Distorted; not recommended.

See Note 1.

Distorted; not recommended.

See Note 1.

Narrow See Note 1 Distorted; not recommended.

See Note 1.

Note 1: Available for 480i, 480p, and digital SD 4:3 signals only.

Original Signal

SD 16:9 or

HD Digital

720p, 1080i,

1080p Signal

Display Formats

Wide

Expand

Recommended to remove side bars.

Zoom Recommended to remove bars from the top, bottom, and sides.

TV Display Formats. Press the MORE key and then

repeatedly press the 0 key (FORMAT) to see the displays available for the current program. Press the INFO key to see the name of the display format in use.

Stretch: Stretches a squarish 4:3 image across the screen to display the entire image with less distortion than the Standard format.

Stretch Plus: Similar to Stretch, but minimizes distortion on the sides by expanding the picture to crop off portions of the top and bottom. Use to adjust the vertical position of the picture.

Narrow: Displays narrow 4:3 images in their original shape. Adds black side bars to fill the screen.

Wide Expand: Enlarges the picture, cropping the image on both sides. Removes or reduces black side bars added to narrow images converted to 16:9 signals for digital broadcast.

Note: All high-definition channels send widescreen

(16:9) signals, but not all programming was created for the widescreen format. The broadcaster may stretch the image or add side bars to fill the widescreen area.

1

HDMI

2

3D Video

This section provides Instructions for viewing 3D video using 3D glasses and the TV’s 3D feature. The

3D options are found in the Adjust > 3D Mode menu described on page 34.

Initial Setup

1. Check if your HDMI 3D video source device outputs a 1080p 60 Hz signal. This information will be needed when you assign an input name in the New

Device Found screen.

2.

RS-232C

If your 3D glasses came with an emitter box, connect the emitter box to the 3D GLASSES

EMITTER jack. Place the box in front of the TV where there is clear path to the glasses.

3. Using TV Features

25

Watching 3D Video

Note: 3D glasses are required.

1.

2.

3.

4.

Press ACTIVITY.

Highlight the icon for the 3D video device and press

ENTER.

Press MENU and select the Adjust > 3D Mode menu.

Select On. The On setting will be memorized for the current input when you exit this menu.

DVI/PC

R

3

AVR

AUDIO

OUTPUT

L

R

Y/ VIDEO Pb Pr

1

HDMI

2

L

3

AUDIO

OUTPUT

R

Y/ VIDEO

Pb

Pr

AUDIO

OUTPUT

R AUDIO 3D

GLASSES

EMITTER

L

Y/ VIDEO Pb Pr

(480i / 480p / 720p / 1080i) IR-NetCommand

R

ANT

DIGITAL

AUDIO

OUTPUT

R AUDIO L

Y/ VIDEO Pb Pr

(480i / 480p / 720p / 1080i) IRNetCommand R

3.

4.

5.

Power on the TV and the source device.

Connect the source device to the TV’s HDMI input.

When the New Device Found screen displays, name the input according to the table below.

The signal type and choice of name are important because the TV will process the video signal differently depending on the name you assign.

If your source device is a Blu-ray disc or game console, the signal must be 1080p at 60 Hz.

Source of 3D

Video

3D Video Signal

Computer Recommended: 1080p 60 Hz

(1920 X 1080). The image will fill the TV screen.

Other 60-Hz computer video signals compatible with the TV will display with black bars. See

“Computer Display Formats” on page 27.

Any other

3D video source

To see 3D video, the signal must be 1080p 60 Hz

Assign

Name

PC

Any other name

6. Press BACK to close the New Device Found screen.

Use the Adjust > 3D Mode menu to enable 3D video.

5.

6.

Press BACK to close the menu.

If the image does not appear correct (e.g., objects appear to be moving in instead of out), open the

Adjust > 3D Mode menu and set Glasses L-R to

Reverse.

To Watch Regular (non-3D) Video

The 3D Mode setting is memorized for each input.

When you want to watch non-3D video on the input selected above, open the Adjust > 3D Mode menu and set 3D Mode to Off.

Important Note About 3D Images

To display 3D images, Mitsubishi Home Theater DLP

TVs require that source devices support checkerboard display formats for 3D gaming or 3D cinema content. A 3D standard format does not currently exist for Blu-ray or DVD prepackaged media. Future

3D standards may be incompatible with Mitsubishi

Home Theater DLP TVs. Please visit mitsubishi-tv.

com for updates and information.

26

3. Using TV Features

Using the TV with a Personal Computer

Connecting a Computer to the TV

Use one of the connection methods listed below based on your computer’s video output.

Computer

Video Output

Video Connection

Digital DVI DVI-to-HDMI cable or an HDMI cable with an HDMI-to-

DVI adapter

HDMI

Audio

Connection

Stereo audio cables

Note: If the computer’s audio output is a single mini jack, a mini audio-to-

RCA-male “Y” adapter cable is also required.

HDMI-to-HDMI cable

No additional audio connection is required.

IMPORTANT

This TV accepts digital computer signals only.

1.

2.

3.

4.

5.

Connect the computer’s digital signal output to one of the TV’s HDMI jacks. See the connection diagrams for the method suited to your equipment.

Connect the computer’s audio output using one of these options:

• For digital DVI signals, connect analog left/right audio to the TV’s DVI/PC INPUT AUDIO jacks.

• For HDMI signals, no additional audio connection is required.

Power on the TV and computer. The TV will detect the connection and display the New Device Found screen.

In the New Device Found screen, press to highlight PC in the list of device types. It is important to use the name PC so that the TV processes the video signal correctly.

Press BACK to close the New Device Found screen.

AUDIO

OUTPUT

L

R

Y/ VIDEO Pb

Pr

TV main panel

ANT

GLASSES

EMITTER

AUDIO

OUTPUT

R AUDIO L

Y/ VIDEO Pb Pr

(480i / 480p / 720p / 1080i)

R

AUDIO

L

Computer with HDMI audio and video output

An HDMI-to-HDMI connection carries all video and audio on a single cable.

1.

1.

AVR

OUTPUT

L

R

ANT

Y/ VIDEO Pb Pr

R AUDIO L

Y/ VIDEO Pb Pr

(480i / 480p / 720p / 1080i) IRNetCommand

Output

R

TV main panel

2.

2.

DVI OUT R

AUDIO

L

Computer with

DVI and stereo audio outputs

A DVI connection from a personal computer requires a separate audio connection. A computer connected to the TV main connector panel is shown above.

TV convenience inputs

Pr Pb

INPUT 3

Y/ VIDEO L AUDIO R USB HDMI 4

Computer with DVI and stereo audio outputs

DVI OUT

AUDIO

L R

HDMI 4

Note: If your computer provides digital audio output (coaxial or optical), you can connect it directly to a digital A/V receiver and bypass the TV.

HDMI-to-DVI cable

837 Series: Computer with DVI output connected to the convenience panel.

3. Using TV Features

27

Using the TV with a Personal Computer

Computer Video Adjustments

1.

2.

3.

4.

5.

WVGA

848 X 480

SVGA

800 X 600

Tip

Power on the computer.

Select PC from the Activity menu. To do this, press ACTIVITY to open the Activity menu, move the highlight to the PC icon, and press ENTER.

Set the computer’s screen saver to display a pattern after several minutes of inactivity. This acts as a reminder that the TV is powered on and the lamp is in use. The lamp is in use whenever the TV is powered on, even if the screen appears dark.

Working from the computer, change the resolution of the computer image. View the computer image on the TV and maximize the computer resolution while maintaining a suitable aspect ratio for the image.

Computer Display Formats

Perform TV video adjustments. Press

MORE then press 8 (VIDEO) repeatedly to access video-adjustment options.

Press MORE then press 0 (FORMAT) repeatedly to cycle through the

TV displays available for your computer’s video signal.

The following additional adjustments are available for computer video:

Computer Signal As Displayed on TV Screen

Horiz Position (Horizontal Position).

Manually adjust the horizontal position.

Original Format

4 X 3

Standard

16 X 9

Standard

Zoom

Vert Position (Vertical Position).

Manually adjust the vertical position.

VGA

640 X 480

Press MORE then press 0 (FORMAT) repeatedly to find the picture format

(aspect ratio) best suited to the image.

See the chart on this page showing how different computer resolutions can be displayed on the TV.

Distortion in Computer Images

Computer images may show distortion when viewed on the TV, e.g., lines that should be straight may appear slightly curved.

WSVGA

1064 X 600

Original Format

XGA

1024 X 768

Standard Zoom

Image Resolution

Your Mitsubishi TV can display the resolutions shown in the chart from standard

VGA (640 x 480) through 1920 x 1080 signals at a refresh rate of 60 Hz.

In most cases, the computer will select the best resolution match to display on the TV. You can override this setting if you wish. Refer to your computer operating system’s instructions for information on changing the screen resolution.

You may need to restart the computer for changes to take effect.

PC 720p

1280 X 720

WXGA

1360 X 768

SXGA

1280 X 1024

Original Format

PC 1080p

1920 X 1080

Standard Reduce

28

3. Using TV Features

Camera Images and Music Files

837 Series TVs Only

• The TV can read photo or music files from a USB device. Photos must be in JPEG format and music files must be in mp3 format. To play music files while displaying a photo slide show, see “USB

Media Setup Menu” on the opposite page.

• The TV can display files of still or moving images from a camera through the Y/VIDEO port.

The USB Media Player Menu

3. From the USB Menu you can:

Activate any of the menu options

Display the Activity menu.

Display the main menu.

Display status for the file source.

Highlight an icon and press

ENTER.

Press ACTIVITY. Press again to clear.

Press MENU. Press again to clear.

Press INFO. Press BACK to clear.

4.

To resume use of the USB port after switching the

TV to a different input, press ACTIVITY, choose View

Photos, and select the USB port.

Displaying the Menu

1. Back up the data on your USB drive before connecting it to the TV. Mitsubishi is not responsible for any file damage or data loss.

2. Connect your USB drive to the TV’s USB port.

The USB Media Player menu displays while files are being read. Wait until icons appear in the menu before continuing.

Pr Pb

INPUT 3

Y/ VIDEO L AUDIO R USB HDMI 4

837 series TVs can read photo and music files from the USB port.

Playing a Slide Show or Playlist

Use these keys while playing a slide show or playlist.

or

ENTER

Replays the slide show or playlist.

Pauses a slide show or playlist.

Stops a slide show or playlist.

GUIDE

Displays the previous or next slide.

Plays the previous or next track.

Rotates an image clockwise in 90˚ increments.

Displays the USB Media Player menu.

BACK

MENU Displays the main menu and stops play.

ACTIVITY Displays the Activity menu and stops play.

INFO

Displays slide name or track name. Press

BACK to clear.

IMPORTANT

Always stop playback with ( STOP) or change to a different TV input before disconnecting your

USB device.

The TV can read JPEG files as created by the camera. If you edit a picture file on a computer and resave the image, the TV may be unable to read the resaved file.

Camera Images and Music Files, continued

Thumbnail and Playlist

Menus

3. Using TV Features

USB Media Setup Menu

29

JPEG Thumbnail Menu

Use these keys while viewing JPEG thumbnail images or the music tracks in a playlist.

Moves the highlight from item to item.

GUIDE

Rotates a thumbnail clockwise in 90˚ increments

or

ENTER

Plays the slide show or playlist starting with the highlighted item.

Selects the last item on the current page.

Selects the first item on the current page.

PAGE UP/DN

Displays the next or previous page of items.

BACK Displays the USB Media Player menu.

MENU Displays the main menu.

ACTIVITY Displays the Activity menu.

Picture Files Compatible with the USB Port

• Still images recorded on digital cameras using the

Exchangeable Image File Format, version 2.1 (EXIF

2.1) standard for digital still cameras and Design

Rules for Camera File Systems version 1.0 (DCF 1.0)

• Some images opened and resaved on a computer may not play back or may not display in the thumbnail list. This happens if the files were resaved in an incompatible format.

• Full path file names can be no longer than 50 characters and must end in a .jpg extension. Only the first 20 of the 50 characters will display.

Use the USB Media Setup menu set up play of a slide show or playlist.

• If JPEG image files and mp3 files are on the USB device, choose:

-

-

-

Slideshow + Music

Slideshow

Music only

Slideshow.

Select either Auto or Manual advance for the slide show. During manual operation, press

ENTER to advance to the next slide.

Interval.

For automatic advance, select the time interval for display of each slide. The interval you select here is the minimum time between slides; actual time may be longer for larger files.

Frequency.

For automatic advance, select the number of times (frequency) to play the complete slide show and/or playlist: Once, Twice, or Continuous.

Press BACK to close the Media Setup menu and return to the Media Player menu.

Notes on Using the USB Port

• The TV ignores all commands while reading files. Wait until the Play icon appears highlighted and in full color before continuing.

• Large files or high-capacity storage devices may take a long time to display.

• The TV can read files up to 10 MB in size with a maximum of 2,500 files stored on the device. The

FAT16 or FAT32 file system is recommended.

• Use a USB drive instead of a card reader.

• Back up the data on your USB drive before connecting it to the TV. Mitsubishi is not responsible for any file damage or data loss.

Note: Some manufacturers’ devices may be incompatible with the TV. If the TV is unable to display your photos, you can:

• Transfer files to a different USB device.

• Use your digital camera’s composite video output. See page 30.

30

3. Using TV Features

Camera Images and Music Files, continued

Photos and Moving Video as Composite Video

Connect the camera to the TV using a composite video cable if:

• You are unable to see images using the USB port.

• You wish to view moving video from the camera.

Control the slide show or movie through the camera as the TV’s USB Media Player menu will be unavailable.

The display resolution will be standard-definition (480i).

1.

2.

3.

Refer to the owner’s manual supplied with the camera for instructions needed for this setup.

Set the camera’s output signal type to NTSC and put the camera into playback mode.

With the camera still turned on, connect your digital camera’s composite video cable (usually yellow) to the TV’s Y/VIDEO jack. To hear audio, connect the camera’s audio output cable to the AUDIO L jack.

4.

5.

6.

When the New Device Found screen displays, assign the name Camcorder.

Press BACK to close the New Device Found screen.

Press ACTIVITY, select Watch Movie > Cam, and press ENTER.

7. If viewing photos, advance through the images manually or set the camera to advance automatically.

Pr Pb

INPUT 3

R USB HDMI 4

Optional

Audio Cable

Camera connection using a composite video cable

3. Using TV Features

Introduction to Home-Theater Control

This TV offers a choice on home-theater-control systems. This summary offers some examples of the control methods available using the TV’s remote control. You may wish to use one or more of these methods in your home theater after completing Auto Input Sensing.

Source device connected directly to the TV

Remote Control Programming (Any Connection Type)

Program the remote control to operate the A/V device. To control the device, set the remote control to the correct mode for the device type. See Appendix A, “Programming the Remote Control.” In the case of an A/V receiver, use the Audio Lock feature, page 59.

Any Connection Type

A/V

Device

TV

CEC-Enabled HDMI Device (HDMI Connection Only)

See Appendix C, “HDMI Control of CEC Devices,” page 67.

CEC-Enabled

A/V Device

HDMI

Cable

TV

31

837 Series: NetCommand IR Control (Any Connection Type)

Set up NetCommand IR control of the device’s keys as desired. See “IR Emitter

Placement,” page 46, and “Initial NetCommand Setup,” page 47.

Any Connection Type

A/V

Device

TV

Source device connected to an A/V receiver connected to the TV

CEC-Enabled HDMI A/V Receiver

The TV’s remote control may operate some functions of a connected A/V device.

You can switch to the device by selecting its icon in the TV’s Activity menu. See

Appendix C, “HDMI Control of CEC Devices,” page 67.

CEC-Enabled

Source Device

A/V Receiver

HDMI

Cable

HDMI

Cable

TV

837 Series: A/V Receiver with HDMI Output (no CEC)

1. Set up NetCommand IR control of the A/V receiver’s keys as desired. See “IR

Emitter Placement,” page 46, and “Setting Up A/V Receiver Control,” page 52.

2. Set up NetCommand IR control of the source device’s keys as desired. See

“NetCommand Control of a Device Connected to an HDMI A/V Receiver,” page

56.

Source

Device

A/V Receiver

Any Connection Type

HDMI

Cable

TV

32

4

TV Menus

Main Menu

Press MENU on the remote control to open the main menu and then select from one of these categories.

Adjust

Customize picture and sound settings.

Captions

Turn closed captions on and off; customize caption displays.

Initial

Input

Perform basic TV setup. Set language, scan (memorize) channels and edit channel options, set the TV clock, set Lamp Energy, set auto-on TV Timer.

Assign names to TV inputs, enable HDMI Control, assign activities to inputs.

837 Series. Perform NetCommand IR “learning.”

Lock

Restrict TV use. Disable the control-panel buttons. Set a pass code.

38

40

33

37

42

Menu Navigation

Displays or clears the main menu.

Moves up one menu level.

Clears the current menu.

Moves navigation into options area.

Selects an item.

Moves the highlight within menus.

Makes adjustments in some menus.

Look for the key guide at the bottom of each menu.

Picture

Audio

Adjust

See page 35 for picture adjustments.

See page 36 for audio adjustments.

Reset

Global

4. TV Menus

33

Resets audio and picture adjustments for the current input. Highlight the Reset icon and press

ENTER twice.

Reset has no effect on global settings (

Advanced Picture).

Balance, Listen To, Language, Film Mode, and

Video Mute

(non-antenna inputs only)

Audio

Screensaver

Film Mode

(480i and 1080i signals only)

On

Off

Displays a solid colored background when there is no video signal from the current input. The colored screen reminds you that the

TV is powered on when there is no picture. The TV will power off after five minutes without receiving a video signal.

The screen appears black when there is no video signal from the current input.

On, Off Select On to display a random pattern while playing an audio-only input. To use this feature, the input must be either

• Named as an audio source (e.g., CD or MP3 Player) and selected under the Listen Music activity.

or

• Be the ANT input.

Auto, Off In Auto, the TV automatically detects and applies film-decoding correction to movies filmed at 24 frames per second. Try the Off setting if images show many jagged edges.

Smooth 120Hz Off, On When On, Smooth 120Hz™ reduces motion blur in action scenes but may show pixel structure during slower motion or in still images.

Blue Glow

(837 series)

On, Off Select On to see blue accent lighting when the TV is powered on.

Displays a test picture for use by TV servicers.

Test Picture

34

4. TV Menus

Picture+

3D Mode

Adjust, continued

PerfectColor Sliders Adjusts the saturation (intensity) of six colors for the current image source.

PerfectColor

PerfectTint Sliders

(837 series)

Adjusts six hues for the current image source

Using PerfectColor:

Highlight the PerfectColor™ icon and press ENTER to display the PerfectColor menu. Settings are retained independently for each TV input.

Using PerfecTint (837 Series):

• To switch between PerfectColor™ and PerfecTint™ adjustments, highlight Adjust Mode and press .

• Press to move from one color bar to the next.

• Press to change settings.

• Press CANCEL to restore default settings.

• Press MENU to return to the main menu.

Advanced

Picture

Advanced Picture allows you to save highly customized picture adjustments for each input. Mitsubishi recommends a professional installer make these adjustments.

3.

4.

5.

6.

1.

2.

Press MENU. Under Picture+, highlight the Advanced Picture icon and press ENTER.

With Picture Mode highlighted, press ENTER to change from blank (undefined) to ADV.

837 Series: Choose ADV1 (daytime settings) or ADV2 (nighttime settings)

Use to highlight an option you wish to change and press ENTER to see the adjustment display.

Press to change settings.

Use to navigate to additional options and press to change settings.

Press MENU to return to the Advanced Picture menu. Press MENU to close the menu. The

Advanced Picture adjustments will be in effect for the current input.

To use the custom Picture Mode at a later time

Press MENU and go to Adjust > Picture > Picture Mode and:

737 and C9 Series

• Select SPECIAL if settings were saved by your professional installer.

• Otherwise select ADV.

837 Series

• Sele ct ISF Day or ISF Night if settings were saved by your professional installer.

• Otherwise select ADV1 or ADV2.

To return to the default values for Advanced Picture

Display the Picture+ > Advanced Picture menu and:

737 and C9 Series

Highlight

3D Mode

RESET Pic Mode and press ENTER.

Glasses L-R

On, Off

Standard,

Reverse

837 Series

1. Highlight the Advanced Picture mode to change.

2. H ighlight RESET Pic Mode and press ENTER.

Repeat this separately for both ADV1 and ADV2.

Use the On setting for video games and movies that require 3-D glasses. This setting applies only to the current input.

Note: 3D options are available only for 1080p 60-Hz video sources connected to an HDMI input.

Synchronizes the 3D glasses with the image on screen to provide the best 3D effect. Try Reverse if Standard seems incorrect.

4. TV Menus

35

Adjust, continued

Picture

Assign names to TV inputs before making video adjustments ( New Device Found or

Inputs > Name menu). Adjustments will be reset to the defaults if you name or rename inputs afterwards. To make picture adjustments:

• From the Adjust > Picture menu:

1.

2.

Press

Press

to highlight an option.

to adjust.

While watching TV: Press the MORE key and then

8 (VIDEO) in the on-screen menu. Press to select the video option you want to change. Press

to change settings.

Picture

Mode

Contrast

Brilliant

Game

Bright

For use under bright light; unavailable when the current input is named

Game or PC.

Game or PC.

Optimizes picture and video processing for gaming consoles. Available only when the name of the input is

For most daytime viewing and x.v.Color sources

Set the Picture Mode first before changing other video settings, as some settings are stored independently for each

Picture Mode. Use Picture

Modes to get the best image under different viewing conditions.

Natural For most nighttime viewing and x.v.Color sources

Special

ISF Day,

ISF Night

Advanced Picture Modes. Contact your professional installer for setup or see “Advanced Picture” on the opposite page.

737, C9 series: Special/ADV

837 series: ISF Day/ADV1, ISF Night/ADV2

Low contrast shows a variety of shades in darker images

In most home lighting situations, medium contrast looks best.

High contrast shows darker images more uniformly black and makes colors appear more vibrant. High contrast is good for brightly lit environments.

Adjusts the white-to-black level

Settings are stored independently for each Picture Mode.

Brightness Adjusts overall picture brightness. Settings are stored independently for each Picture Mode.

Color Adjusts overall color intensity from no color to fully saturated.

Tint Adjusts the red-to-green ratio.

Sharpness Adjusts picture detail and clarity.

Color

Temp

Video

Noise

SharpEdge

High

Low

High

Medium

Low

Off

On, Off

Gives white images a cool cast. May provide the most realistic picture under bright lighting.

Adjusts the white balance.

Settings are stored independently for each Picture Mode.

Gives white images a warm cast. Natural/Color Temp at the low setting displays video at approximately the

6500K industry standard for NTSC pictures.

Use

Use

Use

Use

High with poor-quality signals.

Medium for moderate noise reduction.

Low with good-quality signals.

Off to leave the picture unaltered.

Reduces minor noise (graininess) in the picture. Saved by input. This adjustment is not available if the current input is named PC or Game or when 3D is active.

737, 837 Series. SharpEdge™ adds special edge enhancements to make the image appear sharper. Saved by input.

DeepField

Imager

On, Off

Demo

737, 837 Series. DeepField™ Imager dynamically enhances black levels in portions of the screen to provide strong contrast with detail over mixed screen content.

For comparison, displays a split picture to show On (right side) and Off (left side).

36

4. TV Menus

Adjust, continued

Audio

To make audio adjustments:

From the

1.

2.

Press

Press

Adjust > Audio menu:

to highlight an option

to adjust.

While watching TV: Press the MORE key and then 9

( AUDIO) in the on-screen menu. Press to select the audio option you want to change. Press to change settings.

Speakers The Speakers option displays only if an A/V receiver or headphone connection has been detected. Detection occurs on the right AVR AUDIO OUTPUT jack and the DIGITAL AUDIO OUT jack. An A/V receiver can also be detected on an HDMI jack.

TV Turns on the internal TV speakers.

AV Receiver Turns off the TV speakers so you hear sound only from a connected A/V receiver.

Note: When you disconnect an analog A/V receiver, be sure to change the

Speakers setting to TV to hear sound from the TV speakers.

Headphones Turns off the TV speakers so you hear sound only from connected headphones.

See “7. AVR AUDIO OUTPUT,” page 16. This option is not available if DIGITAL

AUDIO OUTPUT is connected.

Controls volume of low-pitched sound from the TV speakers.

Bass

Treble Controls volume of high-pitched sound from the TV speakers.

Balance Controls audio balance between the right and left TV speakers

Sound Mode Stereo

Listen To

Applicable only to analog channels from the

ANT input

Language

No special audio effects from the TV speakers

Surround Modifies audio from the TV speakers.

• For monaural (non-stereo) programs, creates a simulated stereo effect.

• For stereo programs, creates a simulated surround sound effect.

Stereo

Mono

The TV plays stereo broadcasts in stereo and mono broadcasts in mono. The word Stereo is displayed when you tune to a channel broadcasting in stereo.

Reduces background noise. Use when receiving a weak stereo audio signal. All audio is played as mono with this setting.

SAP

(Second

Audio

Program)

Selects an additional monaural sound track not audible during normal TV viewing.

The SAP signal might be related to the program (such as a sound track in a foreign language), or it might be unrelated (such as a weather report). If an SAP signal is broadcast, the letters SAP are displayed when you tune to the channel.

Selects the current language for a digital program from the ANT input. Each digital program may include from zero to seven language choices.

Level Sound

Available only for digital channels from the ANT input.

On, Off Reduces differences in sound volume between programming segments, such as the difference between regular broadcast programs and commercial segments.

Captions

Captions on Analog Channels

The TV can decode captions from the ANT INPUT and the composite VIDEO jacks. Broadcasters can send either standard closed captions or text service. Standard closed captions follow the dialogue of the program and display in a small section of the screen. Text-service closed captions often contain information such as weather or news and cover a large portion of the screen.

Captions on Digital Channels

The TV can decode captions from the ANT input only.

Broadcasters can send up to six different captioning selections or can send analog captions for a program that originated in analog format. A TV station may broadcast only one or two types of captions or none at all.

4. TV Menus

37

IMPORTANT

• Analog text-service options display a large black or gray box on the screen when no signal is being broadcast.

• The content of captions is determined by the broadcaster. If captions show strange characters, misspellings, or odd grammar, it is not a malfunction of the TV.

• Closed-caption signals are not available through

HDMI or component jacks. See the menus for devices connected to these inputs for closedcaption decoding.

Services

Effects

(for captions from digital channels)

Digital

Analog

Analog Background

Font

On if Mute

Caption 1–

Caption 6

Off

On if Mute

CC 1–CC 4

Text 1–Text 4

Off

Gray, Black

Default

Font 1–Font 7

On if Mute: Displays digital closed-caption signal Caption 1 when audio from the TV speakers is muted. When watching

TV, press MUTE to turn closed captions on/off.

Caption 1–Caption 6: Caption signals sent by the broadcaster

On if Mute: Displays analog closed captions signal CC 1 when audio from the TV speakers is muted. When watching

TV, press MUTE to turn captions on/off.

CC 1–CC 4: Standard closed-caption signals

Text 1–Text 4: Text-service signals

Selects either a gray or black text background to make analog closed captions easier to read.

Default changes settings to those selected by the captions provider, or, if none, to the TV’s own caption defaults. Use Fonts 1 through 7 to give captions on digital channels a custom appearance.

Font Size Large

Medium

Small

Large is the recommended size.

White, Black, Magenta, etc.

Guidelines for setting digital captions: Font Color

Font Opacity Translucent, Opaque, Flashing,

Transparent

Background

Color

White, Black, Magenta, etc.

• A white font on a black translucent background makes an easy-to-read combination.

• Use contrasting colors for captions and background.

Background

Opacity

Translucent, Opaque, Flashing,

Transparent

38

4. TV Menus

Initial

Language

Clock

Timer

English

Spanish

Displays on-screen menus in either English or Spanish.

Note: To listen to audio in other languages (when available), see Adjust > Audio >

Listen To > SAP (analog signal) or Language (digital signal) on page 36.

Set the TV clock to:

Use the TV Timer to power on the TV automatically at a preset time

Receive correct updates to ChannelView listings

Note: When the Daylight Savings Time change occurs, you must open this menu and set the TV’s clock ahead or back.

Time 1.

2.

3.

With the hour highlighted, press to change the hour and the AM/PM indicator.

Press and hold to change the hour display quickly.

Press ENTER to set the hour.

With the minutes highlighted, press change the minutes display quickly.

to change the minutes. Press and hold to

Date 1.

2.

3.

With the month highlighted, press

With the day highlighted, press

With the year highlighted, press

to select. Press ENTER to set.

to select. Press ENTER to set.

to select the current year.

Time Zone Eastern, Central, Mountain, Pacific, etc. The correct time zone is required for accurate

ChannelView updates.

DST On, Off Daylight Savings Time. Select the setting for your area. The correct DST setting is required for accurate ChannelView updates.

Timer On, Off Select On to enable the Timer.

The Timer tells the TV to power on automatically at a time you set. Use this menu to set a day, time, input, and channel for the Timer. If the TV is already on at the requested time, the TV will automatically change to the designated channel or input.

• The TV clock must be set before you can use the Timer feature.

• To remind you that the TV Timer has been set, the POWER indicator on the front of the TV flashes slowly while the TV is powered off.

• When the Timer turns on the TV, press any key on the remote control to keep it on. Otherwise, the TV will turn off after five minutes.

Day Daily, Mon-Fri, (every) Sunday, (every) Monday, (every) Tuesday, etc.

Select the day or days of the week for the Timer to turn on the TV.

Time

Input

To set the time for the TV to come on:

4.

5.

6.

With the hour highlighted, press

PM indicator. Press and hold to change the hour display quickly.

Press

Press

repeatedly to change the hour and the AM/

ENTER to highlight the minutes.

to change the minutes. Press and hold to change the minutes display quickly.

Ant, DVD, VCR, etc.

Select the input you want displayed when the TV comes on. Choose from the defined and enabled inputs that appear in the Activity menu.

Channel If the source is the ANT input, select a channel number by pressing or press and hold to scroll through channels.

4. TV Menus

39

Initial, continued

Channel

(Channel

Management)

Ant Air,

Ant Cable

Scan

Edit

You must perform a channel scan to receive digital channels. Scan searches for broadcast channels and adds them to TV memory. To start channel scan:

1.

2.

3.

Highlight one of the input selections based on your connection to the ANT input:

Air when connected to an indoor or outdoor antenna.

Cable when connected to direct cable (no cable box)

Press

Press

to highlight SCAN.

ENTER to start channel memorization.

After channel scan, Edit lets you add and delete memorized channels.

• Press PAGE DN/UP to jump to the next or previous page of channel numbers.

• Press to move through all channel numbers, one at a time.

Notes on Scan and channel memorization

• Channel memorization may take up to 15 minutes to complete.

• To stop channel memorization before completion, press CANCEL. Channels already added are retained.

• When watching TV, press CH to move through memorized channels.

• To add a digital channel that does not appear in the

Edit menu without repeating channel memorization:

1.

2.

Look up the physical channel number for the new digital channel. See the website

www.antennaweb.org for help.

Press ACTIVITY and select the ANT input.

3. Use the number keys and CANCEL key to enter the physical channel number followed by “-1” and ENTER. For example, for physical channel

36, press

3 6 1 ENTER.

The TV will search for a digital channel on the channel

36 frequency. When it finds the channel, it will: a. Add the channel to memory.

b. Change the channel number to the virtual channel number sent by the broadcaster.

c. Add to memory any associated subchannels.

Rememorize channels if you move the TV to a different geographic area with a different channel line-up.

Adding/Deleting Channels Using the Channel Edit Menu

• Channels marked with a check are in memory.

To add or delete a channel from memory, highlight the channel number and press ENTER.

To add a single digital channel not in the list, see the notes under Scan on this page.

Digital channels are listed by virtual channel number with the physical channel number shown in small gray text.

See below for an explanation of these terms.

-

-

Virtual Channel Number (digital channels only). A channel number sent by a local broadcaster. Usually the virtual number is associated with the corresponding analog channel number. For example, a broadcaster may associate digital channel 2-1 with their analog channel 2.

Physical Digital Channel Number.

The channel number officially assigned to the actual broadcast frequency; shown on screen in gray text.

Energy Lamp

Energy

Standard,

Bright

Standard is for most viewing conditions. Use Bright in brightly lit rooms.

You may notice increased fan noise when using the Bright setting.

40

4. TV Menus

Inputs

Name Cablebox, Cam(corder), CD, DVD

(DVD, DVD2, Blu-ray), DVR, Game

(Game, PS, Xbox, Wii), MP3 Player,

PC, Satellite, VCR, AVR

Delete (deactivated HDMI only)

On/Off (ANT only)

Lets you assign or change names of inputs appearing in the Activity menu.

Press to move between inputs.

-

-

Press to select a name.

You cannot change the name of the current input; you must first switch to another input. If you have only one input, such as a cable box, make sure the Ant input is

On and switch to Antenna in the Activity menu before renaming the single input.

Lets you turn the Ant input On/Off (to display/hide it in the Activ-

ity menu).

Lets you delete unused HDMI inputs from the

A CEC-enabled tuner can be named either

Satellite.

A CEC-enabled DVD player can be named

Blu-ray.

Activity menu.

Cable Box or

DVD, DVD2, or

General Notes

When you change an input name in the Name menu and then exit the Name menu:

• The name is changed

The icon in the Activity menu is changed

Audio and video settings are changed to the defaults for the new device type.

837 Series: All previous NetCommand IR “learning” for the input is erased.

Notes for HDMI devices

• Disconnecting an HDMI device: When you disconnect an HDMI device, the icon remains in the Activity menu until you remove it. Select Delete in the Inputs > Name menu to remove an unwanted icon for an HDMI input.

• If the New Device Found screen does not display as expected when you connect an HDMI device, see “Reactivating Auto Input Sensing for an HDMI Input,” page 11.

HDMI Control and CEC-Enabled Devices:

If case of CEC conflicts:

See Appendix C, “HDMI Control of CEC Devices,” page 67.

Turn off CEC signals in one of these ways:

-

-

Turn off the TV’s HDMI Control signals to the device.

Turn off each device’s internal CEC capability.

See Appendix C for the TV’s HDMI Control or, to turn on/off a specific device’s response to CEC signals, see the device owner’s manual.

Learn

837 Series

Sets up or changes NetCommand IR control of the current viewing device.

See “About NetCommand IR Control,” page 45.

AVR 837 Series

Sets up or changes NetCommand IR control of an A/V receiver.

See “NetCommand IR Control of an A/V Receiver” on page 51.

HDMI Control On, Off Select On or Off to enable or disable the TV’s control of a CEC-enabled device.

See Appendix C for use of this feature.

Activity •

Lets you customize the Activity menu choices for the current input.

Highlight the activity name and press ENTER to make changes.

See “How is the Activity Menu Generated?” on the opposite page.

Inputs, continued

How is the Activity Menu Generated?

The TV automatically generates the Activity menu based on recognized inputs. If the inputs have been named as device types, the TV groups the device types based on how they can be used. The device names used for groupings are those assigned in the New

Device Found menu or the Inputs > Name menu. The table below summarizes the device groupings that can appear in the Activity menu.

Key

Activity assignments made automatically by the TV.

X Activity assignments you can make using the

Inputs > Activity menu.

Antenna

AV Receiver

Blu-ray

Cable Box

Camcorder

CD/Audio

DVD

DVD2

DVR

Game

MP3 Player

PC

PS

Satellite

USB

VCR

Wii

Xbox

Watch

TV

Watch

Movie

Play

Game

View

Photos

Listen

Music

X

X

X

X

X

X

 

X

X X

 

X

X

4. TV Menus

41

42

4. TV Menus

Lock

TV Locks

Parental Lock by Program Ratings

Restricts access using U.S.-based ratings sent by broadcasters.

Time Lock by Time

Restricts TV use by time of day.

Panel

Other

Lock Control Panel

Disables the buttons on the TV’s control panel. Use this option if small children in the home try to press control-panel buttons.

Lock by Other Program Ratings

Restricts access using non-U.S.-based ratings sent by broadcasters.

Pass Codes

Setting a Pass Code

You are prompted to enter a pass code whenever you select Lock on the main menu. To set a pass code for the first time:

1. Press MENU and highlight Lock. A screen prompting you for a pass code will display.

2. Input a four-digit pass code using the number keys on the remote control.

• Press CANCEL to delete a number and move back one space.

3.

• Press MENU or BACK to close the menu without setting a pass code.

Press ENTER to set the pass code.

Resetting a Pass Code

See the procedure in Appendix B.

Parental Menu

The TV comes from the factory with the rating locks turned off and with pre-set U.S. ratings TV-PG and movie rating PG. Turn on blocking for U.S. ratings to activate these rating restrictions. Use the Lock >

Parental menu to change the level of blocking with U.S. ratings.

Any time you change the channel or device, it may take up to five seconds for the rating restrictions to take effect.

Other Menu (Alternate Rating System)

This TV can recognize new rating systems that may come into effect in the future. The Other menu allows you to block digital programming when such systems come into effect.

The first time you tune to a channel broadcasting an alternate rating system, the TV defaults to the most restrictive setting if the Lock menu > Other Lock option is set to On. Use this menu to change the allowed rating if you are unable to watch a program rated with an alternate system.

Bypassing TV Locks

If you try to watch a blocked program or the TV is locked by time, a notice will appear prompting you for a pass code. To use the TV, input your four-digit pass code and press ENTER.

-

-

To reactivate the locks after using a pass code, power the TV off and then on.

To reactivate only the parent ratings lock, change to a different channel or device.

If a program is blocked, you can still use the TV without entering a pass code. Change to a channel airing an allowed program or change to another device.

Important Notes on Rating Locks

Parental menu rating locks apply only to channels and signals received on the ANT and composite VIDEO jacks.

Other menu rating locks apply only to digital channels received on ANT.

• When viewing a cable box, satellite receiver, or other device connected to the component

Y Pb Pr or HDMI inputs, check the device’s owner’s guide for parental locks.

4. TV Menus

43

Lock, continued

L

S

V

FV

D

Parental

Lock

Start

Time

Stop

Time

TV

Rating

Movie

Rating

Off, On Disables or enables blocking based on V-Chip signals and the U.S. rating system.

Sets the time of day for enforcement of rating restrictions set in the Parental menu.

1. Highlight the hour digits for Start Time.

2.

3.

4.

5.

Press repeatedly to change the hour and associated AM/PM indicator. You can also just press and hold to move quickly through the numbers.

Press ENTER to highlight the minutes.

With the minutes digits highlighted, press repeatedly to change the minutes. You can also just press and hold to move quickly through the numbers.

Highlight the Stop Time digits and set the time as described above.

Note: To make rating restrictions active 24 hours a day, make Start Time and Stop Time the same.

TV-Y

TV-Y7

TV-G

Youth. For children under 7.

Youth 7 and older.

General Audience. For the entire family.

Highlight the rating level you wish to change and press ENTER to block it

( ) or allow it ( ).

TV-PG

TV-14

TV-MA

Parental Guidance. Parental Guidance recommended; may not be suitable for some children.

Adolescent 14 and older. Not recommended for children under 14.

Mature Audience. For adults only.

You can apply supplemental content blocking to the age-based ratings by using the TV content categories listed below.

Fantasy Violence. Applies to TV-Y7 only.

Sexual Dialog. Applies in differing degrees to TV-PG and TV-14.

Adult Language. Applies in differing degrees to TV-PG, TV-14, and TV-MA.

Sexual Situations. Applies in differing degrees to TV-PG, TV-14, and TV-MA.

TV Content

Categories

Violence (graphic or realistic). Applies in differing degrees to TV-PG,

TV-14, and TV-MA.

G General Audience. Designed for the entire family.

PG

PG-13

R

NC-17

X

Parental Guidance. Parental Guidance recommended; may not be suitable for some children.

Parental Guidance, 13 and Older. Not recommended for children under 13.

Restricted. Restricted in theaters to 17 years old and older unless accompanied by an adult.

No Children 17 or Under. Restricted in theaters to 18 years old and older.

Adult. Designed for and restricted in theaters to adult audiences only.

Not Rated No MPAA rating assigned

44

4. TV Menus

Lock, continued

Blocks all use of the TV during the time period you specify. You must enter a pass code to use the

TV when the time lock is in effect.

Time

Panel

Other

Lock by Time Enables/disables Lock by Time.

Lock Time,

Unlock Time

To set the lock and unlock times:

1.

2.

Highlight the hour digits for the

Press

Lock Time.

repeatedly to change the hour and associated AM/PM indicator. To move quickly through the numbers, just press and hold.

3.

4.

5.

Press ENTER to set the hour and highlight the minutes.

With the minutes highlighted, press repeatedly to change the minutes. To move quickly through the numbers, just press and hold.

Highlight the Unlock Time digits and set the time as described above.

Off, On

Note: To make Lock by Time active 24 hours a day, make Start Time and Stop Time the same.

On locks and Off unlocks the buttons on the TV’s control panel. Use this option if small children try to press TV buttons.

To release the Panel Lock from the TV’s control panel, press and hold the

ACTIVITY button for ten seconds. If the TV is powered off, press POWER after the lock releases to make the TV power on.

To reactivate the lock, return to this menu and change the setting to On.

Other Menu Options (alternate rating system)

This TV can recognize new rating systems that may come into effect in the future. The Other option remains grayed out until the TV receives a signal using an alternate rating system. Such alternate rating systems will apply only to digital programming received on the ANT input.

Lock On, Off Enables/disables program blocking.

System Name The rating system available for the channel

Group Rating groups available in the rating system shown on the screen. Rating groups are defined by the rating system in effect.

Rating Rating restrictions available in the selected rating system and group. Highlight the rating and press ENTER to check (block) or uncheck (allow) rated content.

5

NetCommand IR Control

About NetCommand IR Control

NetCommand IR home-theater control is available on 837 series models.

IR emitter cables are available for purchase

from Mitsubishi. Visit www.mitsuparts.com or call

800-553-7278 and request one of the following:

-

-

242D483020 (two-ended cable)

299P254020 (four-ended cable).

NetCommand setup is optional.

You can perform NetCommand setup when the TV first recognizes a device during Auto Input Sensing or at any convenient time afterward.

NetCommand operates by sending remote control signals from the TV to your other devices via the

IR (infrared) emitters, telling the devices to play, record, change inputs, adjust volume, change channels, or perform other functions. All this is accomplished with the TV’s remote control left in TV mode.

You may wish to use NetCommand IR control to supplement control of CEC-enabled devices.

Important Note on NetCommand

Be sure to connect the IR emitter cable to the

TV and properly place the emitters so that

NetCommand can control your devices.

45

In front of a single average-sized device

IR sensor

On top of a single tall device

IR sensor

On top of a single tall device

IR sensor

IR sensor

In front, shared by two average-sized devices

IR sensor

D I G I T A L

S U R R O U N D

TV Main

Panel

IR sensor

46

5. NetCommand IR Control (837 Series)

In front of a single averagesized device

IR Emitter Placement

IR sensor

1.

The NetCommand system uses emitters connected to the IRNetCommand Output jack to control other devices such as DVD players, cable boxes, satellite receivers, and VCRs.

IR emitter cables are available for purchase from

Mitsubishi. Request either part number 242D483020

(two-ended cable) or part number 299P254020 (fourended cable).

1.

2.

Connect the plug end of the IR emitter cable to the

IR—NetCommand Output jack on the TV back panel.

When the New Device Found screen displays, highlight EXIT and press ENTER.

CH

Other A/V Device

A/V Receiver

Connecting IR–NetCommand Output

In front of a single average-sized device

AVR

OUTPUT

L

R

IR-

NetCommand

Output

R

Y/ VIDEO Pb Pr

R AUDIO L

Y/ VIDEO Pb Pr

(480i / 480p / 720p / 1080i)

IR sensor

ANT

In front, shared by two averagesized devices

On top of a single tall device

IR sensor

In front, shared by two average-sized devices

IR sensor

Place IR emitters so the signal can be “seen” by the IR sensor on each device.

The New Device Found screen displays when you connect the IR emitter.

3. Position the emitter end with the emitter bulb facing the device’s remote control sensor. The bulb emits infrared light in a cone-shaped pattern. Place the bulb far enough from the sensor to allow the cone pattern to reach the sensor.

In some cases, the emitter works better facing downward from the top of the device. Experiment to find what works best.

4.

5.

Secure the emitter ends in place using doublesided tape.

Place any unused ends behind the devices to prevent stray signals from reaching the IR sensors.

If You are Unable to Locate a Device’s IR Sensor

The IR sensor is usually behind the plastic window of the front display panel. Using a flashlight, you may be able to see it as a round or square cutout.

If you cannot see the sensor and the device’s

Owner’s Guide does not specify the location, do the following using the device’s remote control.

1. Starting at one end of the plastic window, hold the device’s remote control about one-half inch from the front of the device and press the

POWER key.

2. If the device does not respond, move the remote control one inch toward the center and try again. Repeat until the device responds.

3. Repeat the previous steps starting at the other end of the window. The sensor will be between these two points.

IMPORTANT

Position IR emitters so that each device’s sensor “sees” the signal from only one emitter.

Otherwise, a device receiving signals from multiple sources (remote controls, IR emitters) may not respond at all.

5. NetCommand IR Control (837 Series)

47

Initial NetCommand Setup

To perform this procedure, you need:

The remote controls for both the TV and the device you want to control.

An IR emitter cable available from Mitsubishi .

Note: To set up an A/V receiver, see “Setting Up A/V

Receiver Control,” page 52.

1.

2.

3.

Connect and position the IR emitters for the devices you wish to control. See “IR Emitter Placement” on the opposite page.

Set the TV’s remote control to TV mode and power on the TV.

Open the NetCommand Learn screen as follows:

If working from the New Device Found screen after the device is first detected, highlight

NetCommand and press ENTER to open the

Learn screen for the device.

If performing NetCommand setup at any time after the device has been recognized through

Auto Input Sensing:

a. Press ACTIVITY.

b. Highlight the desired input icon and press

ENTER to switch to that input.

c. Press MENU, highlight Inputs, and highlight

Learn to open the Inputs > Learn screen for the device.

4.

5.

6.

The first function highlighted in the Learn screen is always Power On. Aim the TV’s remote control at the TV and press ENTER to begin learning for that function.

When the Power On text starts flashing, aim the

device’s remote control at the TV and hold the POWER key until a check mark appears next to Power On.

• If the text stops flashing before the check mark appears, repeat the previous step.

• To remove the key from NetCommand control, press the CANCEL key while the key name is highlighted.

Press the keys on the TV’s remote control to highlight other keys on the list. Repeat steps

4 and 5 for each additional function you wish to control through NetCommand.

Note: Device keys in the far right column will be associated with the remote control’s MORE key when

“learned.” See the table on page 49.

7.

8.

If the device has a separate POWER OFF key, press

on the TV’s remote to highlight Power Off.

Repeat the earlier steps to “learn” the POWER OFF key.

If the device has no POWER OFF key, skip this step.

Press BACK to finish NetCommand “learning” for the current device.

From the New Device Found screen, highlight

NetCommand and press ENTER to open the Learn screen.

Device-specific keys in the rightmost column can be accessed with the MORE key after “learning.”

Inputs > Learn screen

Key names marked with a check have been “learned.”

Adding or Removing Device Keys from

NetCommand Control

1.

Switch the TV to the device. Press ACTIVITY, highlight the device’s icon, and press ENTER.

2.

3.

Open the Inputs menu and highlight the Learn icon.

When the Learn screen displays:

To add keys: Continue as described earlier under “Initial NetCommand Setup” on this page.

To delete keys: Highlight the name of the key you wish to delete and press CANCEL on the

TV‘s remote control to clear the check mark.

48

5. NetCommand IR Control (837 Series)

Operating NetCommand-Controlled Devices

2.

3.

4.

Controlling Most Device Types

As an example of NetCommand control, if you are watching your cable box and you wish to tune to the next channel higher, press CHANNEL UP. NetCommand then sends the “learned” channel-up control signal to the cable box.

1. Perform NetCommand setup for the device as described in this chapter.

When you wish to use the device, press ACTIVITY.

Press to highlight the icon for the device.

Press ENTER to switch the TV to the device.

Note: if you have set up automatic input switching for the A/V receiver, the A/V receiver will automatically switch to the correct input for the device.

5. To operate the device using the TV’s remote control, press the side button to put the remote control into TV mode.

6.

7.

Point the remote control at the TV (not the device) and press the key for the desired function.

Press the MORE key to access additional key functions you may have “learned” for the device.

Special Operation Methods

Key Name in

Learning Screen

Special Operation Description and Setup

Power On Manual Power On/Off

Use for devices that have only one POWER key.

Power On

Power Off

Menu

Guide

How to Use

1.

2.

3.

Press ACTIVITY.

Press to highlight the icon for the device to be powered on or off.

With the Activity menu still displayed, press

POWER to send the power signal; you may need to press POWER twice.

Automatic Power On/Off

This feature is only for devices that have separate

POWER ON and POWER OFF keys on their original remote controls. If your device does not have a separate POWER OFF key, do not use the Power

Off learning position; use only the Manual Power

ON/OFF method described above.

In the NetCommand Learn screen: a. “Learn” the Power On command in the

Power On learning position.

b. “Learn” the Power Off command in the

Power Off learning position.

Displaying a Menu for the Current Device

Note: If you press POWER without the Activity menu displayed, the TV will turn off.

4.

Press

To Power On the Device

1.

2.

3.

ENTER to switch the TV to the device.

Press

Press

ACTIVITY.

to highlight the icon for the device to be powered on or off.

Press ENTER to switch the TV to the device and NetCommand will send the

Power On command to the device.

To Power Off the Device

When you turn the TV off, the TV sends all learned Power Off commands to all devices.

Press MORE and then 1 to send the menu command to the current device.

“Learn” the MENU key on the original remote in the

Menu learning position.

Displaying the On-Screen Program Guide

(cable box or satellite receiver)

1.

2.

1.

“Learn” the GUIDE key on the original remote in the Guide learning position.

Learn the PAGE UP and PAGE DOWN keys of the original remote in the Page Up and Page

Down learning positions.

2.

While watching the device, press display the guide.

Press PAGE UP/DOWN ( ) to send the Page

Up/Dn commands for the guide.

GUIDE to

5. NetCommand IR Control (837 Series)

49

Operating NetCommand-Controlled Devices, continued

Key Name in

Learning Screen

Enter

Special Operation Description and Setup How to Use

ENTER-Key Functions (cable boxes, satellite receivers, etc.)

Some devices have two keys that have “enter” functions. One key is for menus and is often labelled

SELECT or OK. A second key is for use with number keys for direct channel selection. NetCommand uses the same ENTER key for both operations.

When ENTER has a menu or guide function or when the original remote control uses the same key for menus and channel selection:

1.

2.

Press MENU or GUIDE to display the device’s menu or guide.

Learn the ENTER, SELECT, or OK key in the

NetCommand Enter learning position.

Press ENTER within the menu and

NetCommand will send the Enter signal for menus.

Enter (digits) When ENTER is for channel changes, i.e., the original remote control has a separate ENTER key for this function):

Cancel

(separator)

Learn the ENTER key for channel selection in the NetCommand Enter (digits) learning position. Use this learning position only if the original remote control has separate keys for Enter in menus and Enter for channel selection.

CANCEL as the Cancel or Exit Function

“Learn” the Cancel or Exit function in the

NetCommand Cancel learning position

The symbol “—” can serve as the separator between a digital channel’s main and sub-channel digits, e.g., digital channel 12-1 (main channel is

12, sub-channel is 1).

“Learn” the channel separator function in the

NetCommand – (separator) learning position.

Press digit key(s) and then press

NetCommand will send the channel selection.

ENTER.

Enter signal for

1. Press MENU or GUIDE to display the menu or guide.

2. Press CANCEL and NetCommand will send the Cancel or Exit signal.

Press digit key(s) and press CANCEL.

NetCommand will send the channel-separator signal.

The MORE Key Menu and NetCommand

Perform NetCommand setup for these device-specific keys and then access their functions with the MORE key.

C

D

Device

Key

Menu

Input

SP/EP

A

B

List

On Demand

Device

Key

Top Menu

Angle

Audio (DVD)

Subtitle

Repeat

Bonus View

Setup

Surround

Night

50

5. NetCommand IR Control (837 Series)

Operating NetCommand-Controlled Devices, continued

NetCommand Specialized Device Keys

Refer to this chart when “learning” device keys. “Learn” some, all, or none of the keys used for each device type.

See page 48 for more on keys marked in the “Special

Operation Method” column.

Key Name in

Learning Screen

Power On

Guide

Channel +/Skip +

Channel –/Skip –

Page Up

Page Dn

Up

Down

Left

Right

Enter

Cancel

Play

Stop

Forward

Function

Power On or Power ON/OFF (toggle)

On-Screen Program Guide or DVD Disc Menus

Next Channel Higher/

Skip Forward (Disc)

Next Channel Lower/

Skip Backward (Disc)

Page Up in Guides

Page Down in Guides

Arrow up

Arrow down

Arrow left

Arrow right

Enter or Select (menus)

Cancel or erase (menus)

Start playback

Stop playback

Fast Forward

Rewind Rewind/Fast Reverse

Pause Pause playback

Record Start Recording

1, 2, 3, 4, 5, 6, 7, 8, 9, 0 Digits

Enter (digits)

- (separator)

Last

Info

Use after entering digits to tune directly to a channel by number

Add digital channel separator between main channel number and sub-channel number

Last Channel Recall

On-screen status display or information display

Power Off Power Off

Name on TV

Remote Control

See Special

Operation

Method Table

1, 2, 3, 4, 5, 6, 7, 8, 9, 0

May require two keypresses

6

NetCommand IR Control of an A/V

Receiver

Controlling an A/V Receiver after NetCommand Setup

Several types of A/V receiver control can be set up using the Inputs > AVR menu.

Power and volume.

See the next page.

Audio switching.

For most equipment setups, see

“Case 1: Automatic A/V Receiver Switching to the

TV Audio Input” page 53.

Audio switching and surround sound.

To set up switching to a surround sound device, see “Case

2: Automatic A/V Receiver Switching to a Surround

Sound Device” page 54

Audio and video switching over HDMI . If your

A/V receiver has an HDMI output, it may be convenient to send audio and video to the TV over a single HDMI cable through the A/V receiver. See

“Case 3: Automatic Audio and Video Switching via

HDMI,” page 55.

Switching Audio to and from the A/V

Receiver

1.

2.

3.

Controlling A/V Receiver Power

With Any Connection Type

Note: To set up control of other device types, see

“Initial NetCommand Setup,” page 47.

1.

2.

3.

4.

Press MORE and then 9 (AUDIO).

Press

Press

to show the Speakers option.

to select either AV Receiver or TV.

Press MORE and then 9 (AUDIO).

Press

Press

to show the Speakers option.

to select AV Receiver.

Point the remote control at the TV (not the A/V receiver) and press POWER to power the A/V receiver on or off.

With an HDMI Connection

1.

2.

3.

Press ACTIVITY.

Highlight the A/V receiver icon.

Press POWER.

Controlling Other A/V Receiver Functions

With the A/V receiver powered on and selected, the

TV’s remote control operates the volume and mute functions. Also, when you switch to a device in the

Activity menu, the A/V receiver automatically switches to the correct audio input for the device.

51

52

6. NetCommand Control of an A/V Receiver (837 Series)

Setting Up A/V Receiver Control

Power and Volume

Perform this setup to control the A/V receiver power and volume with the TV’s remote control.

To perform this setup you need:

• The remote controls for both the TV and the

A/V receiver.

An IR emitter cable available from Mitsubishi.

Before You Begin

1.

Connect your A/V receiver to the TV and any additional devices. See “Setting Up TV Inputs,” page 10 and “TV Connections,” page 14.

2. Connect the IR emitter cable to the TV and position the IR emitter where it can send signals to the A/V receiver. See “IR Emitter Placement,” page 46.

3.

Set the TV’s remote control to TV mode using the side button.

Setup to Control A/V Receiver Power and Volume

1.

Open the Inputs > AVR screen in one of two ways:

2.

If using the New Device Found screen for the

A/V receiver, highlight NetCommand and press

ENTER to open the AVR screen.

If performing NetCommand setup at any time after Auto Sensing:

Press MENU, highlight Inputs, and highlight AVR to open the AVR menu.

The first function highlighted in the AVR screen is always Power. Aim the TV’s remote control at the

TV and press ENTER to begin learning for Power.

Inputs > AVR screen. Perform

NetCommand IR “learning” for A/V receiver power and volume keys.

3. When the Power text starts flashing, aim the A/V

receiver’s remote control at the TV and hold the

POWER or POWER ON key until a check mark appears next to Power.

• If the text stops flashing before the check mark appears, repeat this step.

• To remove the key from NetCommand control, press the CANCEL key while the key name is highlighted.

4.

5.

6.

Press the key on the TV’s remote control to highlight other keys in the list. Repeat steps 2 and 3 for each additional function you wish to control through NetCommand.

If the A/V receiver has a separate POWER OFF key, press on the TV’s remote to highlight Power Off.

Repeat steps 2 and 3 to “learn” the POWER OFF key.

If the device has no POWER OFF key, skip this step.

When finished “learning” the power and volume keys, either

To watch TV, press BACK .

To continue with NetCommand setup to control switching of A/V receiver inputs, highlight

NEXT and press ENTER.

IMPORTANT

To hear audio sent from the TV to the A/V receiver, you must have:

• Physically connected the TV to the A/V receiver via the analog or digital audio output.

• Assigned, if needed, the name AVR if using an

HDMI A/V receiver.

• “ Learned” the IR codes for the A/V receiver inputs.

Assigned the TV’s audio output to the correct input in the NetCommand Inputs > AVR menu.

Selected the A/V receiver as the audio source.

Press MORE then 9 (AUDIO), then to show

the Speakers option, then to select the A/V

Receiver.

6. NetCommand Control of an A/V Receiver (837 Series)

53

Setting Up A/V Receiver Control, continued

Automatic Audio or Audio/Video Switching

The following setups enable the A/V receiver to switch automatically to the correct input when you select a device in the TV’s Activity menu.

Three different connection arrangements are described here. Review the descriptions to find the setup needed for your equipment.

To hear digital surround sound from a source device you must use the setup described for Case 2.

To set up control of an A/V receiver you need:

The remote controls for the TV and A/V receiver.

An IR emitter cable available from Mitsubishi.

Connecting cables

Analog Stereo Audio. Audio from sources with only analog stereo output (such as a VCR) can be sent either directly to the A/V receiver or through the TV first.

Mitsubishi recommends you send audio through the

TV as shown in the example. The TV converts analog audio to digital format to send to a digital A/V receiver.

HDMI Digital Stereo Audio. Digital stereo audio from an HDMI connection is available both in digital and analog format from the TV’s analog and digital audio output jacks.

VCR with

Analog Audio Output audio output from

TV (digital or analog)

IMPORTANT

All audio from what you are watching on the TV is always available from both the TV’s AVR AUDIO

OUTPUT and DIGITAL AUDIO OUTPUT jacks.

To use the digital surround sound capabilities of your A/V receiver however, you must connect the audio output from your DVD player, satellite receiver, or cable box directly to the A/V receiver.

Before You Begin

1. Connect your A/V devices to the TV and connect your A/V receiver to the audio outputs on the TV and the DVD player. Note the name of the device connected to each A/V receiver input. See initial setup, page 10, and “TV Connections,” page 14.

2. Position NetCommand IR emitters as described in

“IR Emitter Placement,” page 46.

3. Set the TV’s remote control to TV mode using the side button.

4. Open the Inputs > AVR menu, highlight NEXT and press ENTER to display the device-key-learning menu.

Case 1: Automatic A/V Receiver

Switching to the TV Audio Input

Most devices are set up to use the TV’s audio output like the VCR in this example; analog audio from the device is sent through the TV to the A/V receiver’s TV audio input.

Use this setup for:

• Audio Available from TV only. Send audio from the ANT input to the A/V receiver from the TV’s analog or digital audio output.

Use this setup to make the A/V receiver switch to its designated TV audio input when viewing programming from the ANT input.

TV

TV audio out

DVD audio input

TV audio input

A/V Receiver

Incoming Coaxial Cable to TV’s ANT input

Important: To use this setup, you must connect the TV’s audio output to the A/V receiver’s TV audio input jack.

1.

2.

3.

4.

5.

In the Inputs > AVR menu, press to highlight

TV audio out as the A/V receiver input to control.

Press ENTER on the TV’s remote control.

While the text TV audio out is flashing, press and hold the TV INPUT key on the A/V receiver’s remote control.

When a check appears next to TV audio out, release the TV INPUT key.

If the text stops flashing before the check mark appears, repeat this step.

To erase the IR code just “learned,” press

CANCEL while the name is highlighted.

Press MENU if finished or continue with Case 2 setup if you want to control surround sound switching for another audio source.

Case 1: NetCommand setup for controlling A/V receiver switching to the A/V receiver’s audio input from the TV . The list displayed represents inputs in use.

The device names are those you assigned in the New

Device Found screen or in the Inputs > Name menu.

Incoming

Coaxial

Cable audio + video video

54

6. NetCommand Control of an A/V Receiver (837 Series)

Setting Up A/V Receiver Control, continued

Case 2: Automatic A/V Receiver Switching to a Surround Sound Device

Note: Use this setup to send digital surround sound from a source device directly to your external sound system. For non-surround sound source devices,

Mitsubishi recommends using the setup for Case 1, in which audio is sent through the TV.

A device can send digital surround sound such as Dolby

Digital or DTS directly to the A/V receiver. The device might be a DVD player, cable box, or satellite receiver, and could have HDMI output. A DVD player is used in this example.

Your setup may include additional devices with digital surround sound connected directly to the A/V receiver.

These devices might be a DVD player plus a cable box or satellite receiver.

DVD Player with

Digital

Surround

Sound digital surround sound video

TV

DVD audio input

A/V Receiver

Case 2: A/V receiver audio from a device providing surround sound directly to the A/V receiver

1.

2.

In the Inputs > AVR menu, press to highlight the name of the A/V receiver input to control. In this example, it is the DVD input.

Press ENTER on the TV’s remote control.

Case 2: NetCommand setup for controlling A/V receiver switching to the A/V receiver’s DVD input. The list contains connected inputs with names assigned during Auto

Input Sensing.

3.

4.

5.

While the text DVD is flashing, press and hold the

DVD INPUT key on the A/V receiver’s remote control.

When a check appears next to DVD, release the

DVD INPUT key.

If the text stops flashing before the check mark appears, repeat this step.

To erase the IR code just “learned,” press

CANCEL while the name is highlighted.

If finished, highlight EXIT and press ENTER or continue to set up additional A/V receiver audio sources.

VCR with

Analog Audio Output

6. NetCommand Control of an A/V Receiver (837 Series)

55

Setting Up A/V Receiver Control, continued

Case 3: Automatic Audio and

Video Switching via HDMI

If your A/V receiver has an HDMI output, it may be convenient to route video signals from multiple devices over a single cable to the TV. Use this procedure to set up NetCommand control of the A/V receiver’s audio and video switching over a single HDMI cable. The connected source devices can be analog, digital, or a mixture or the two. When this setup is complete, you can use the TV’s Activity menu to select a video device connected to the A/V receiver.

TV

HDMI Cable

Blu-ray player

Cable box

A/V Receiver

HDMI

Output

VCR

DVD player

Before You Begin

To complete these steps you will need:

• The remote controls for both the TV and the A/V receiver.

• An HDMI-to-HDMI cable to connect the A/V receiver to the TV and cables necessary to connect devices to the A/V receiver.

1.

2.

3.

Connect the A/V receiver to the TV with an HDMIto-HDMI cable. Do not connect the optional audio cable at this time.

If desired, enable HDMI Control of a CEC-enabled

A/V receiver. See Appendix C, “HDMI Control of

CEC Devices.”

Connect your audio/video devices to the A/V receiver. Note the name of the device connected to each A/V receiver input. This information will be needed later to set up NetCommand’s automatic input switching.

TV main panel

Y/ VIDEO Pb Pr

DIGITAL

AUDIO

R AUDIO L

Y/ VIDEO

AVR

AUDIO

OUTPUT

Pr

L

R

IRNetCommand

Output

R

ANT

More About Using an HDMI Connection

• Audio from devices connected directly to the TV can be heard from the TV speakers only. To send audio to the A/V receiver from such devices, use one of the optional audio connections shown in the diagram on this page. For example, use an optional audio connection if you wish to use the A/V receiver speakers to hear audio from:

-

-

The ANT input

A game or camcorder connected to the convenience input ( INPUT 3).

• To use NetCommand to supplement HDMI control of a CEC-enabled A/V receiver, the recommended setup sequence is:

1.

2.

3.

4.

Connect the HDMI cable.

Enable HDMI control ( New Device Found screen).

Connect the secondary digital audio cable, if desired.

Perform NetCommand setup.

If you connect to HDMI after performing

NetCommand setup for the A/V receiver, the

NetCommand setup will be lost.

• In some cases, audio from a device connected to the

A/V receiver may not be passed over the HDMI cable to the TV speakers. In these cases you must use the

A/V receiver speakers to hear audio.

DIGITAL

AUDIO

OUTPUT

Optional analog or digital audio connection

A/V receiver with HDMI output HDMI OUT

DIGITAL

AUDIO

L

High-definition

DVD player

Cable box

R

VCR

DVD player

Multiple video inputs through a single HDMI cable. You can connect multiple video devices to an A/V receiver that has an HDMI output. The optional audio connection allows you to hear, through the A/V receiver, devices connected to the

TV only, e.g., an antenna on the ANT input.

56

6. NetCommand Control of an A/V Receiver (837 Series)

Setting Up A/V Receiver Control, continued

4.

5.

If using an optional audio cable between the TV and

A/V receiver, connect it.

Connect the IR emitter cable to the TV and position the IR emitter where it can send signals to the A/V receiver. See “IR Emitter Placement,” page 46.

Setup to Control Automatic Audio and Video Switching via HDMI

When this setup is complete, the “learned” A/V receiver input will appear in the TV’s Activity menu as a selectable input.

1.

2.

3.

4.

5.

Power on the A/V receiver.

Set the TV’s remote control to TV mode using the side button.

Power on the TV.

When the New Device Found screen displays, select device name AVR if it is not recognized automatically.

Navigate to the Inputs > AVR menu or, from within the New Device Found screen, highlight

NetCommand and press ENTER.

NetCommand Control of a Device Connected to an HDMI A/V Receiver

Use this setup to have NetCommand control a device sending audio and video through the A/V receiver to the

TV via HDMI.

You must have already completed the procedure under

“Setup to Control Automatic Audio and Video Switching via HDMI” on this page. That procedure placed an icon in the Activity menu for the device (input) connected to the A/V receiver.

Any Connection

Type

HDMI

Cable

Source

Device

A/V

Receiver

TV

1.

2.

3.

4.

5.

6.

7.

Set up NetCommand control of A/V receiver audio/ video switching via HDMI as described on this page.

Press BACK to close any open menus and return to normal TV viewing.

Press ACTIVITY.

Highlight the icon for the A/V receiver input you wish to control.

Press ENTER to switch the TV to the A/V receiver and the A/V receiver to the input.

Open the Inputs > Learn menu.

Perform NetCommand “learning” for the connected )device by following the steps in “Initial

NetCommand Setup,” page 47.

To set up A/V switching over HDMI, choose your devices from a list. Unlike the device list described for

Case 2, this is a generic list containing more than just the devices detected in your setup.

6.

7.

8.

9.

In the Inputs > AVR menu, press to highlight the name of the A/V receiver input to control. In this example, it is the DVD input.

Press ENTER on the TV’s remote control.

While the text DVD is flashing, press and hold the

DVD INPUT key on the A/V receiver’s remote control.

When a check appears next to DVD, release the

DVD INPUT key.

If the text stops flashing before the check mark appears, repeat this step.

To erase the IR code just “learned,” press

CANCEL while the name is highlighted.

10. If there are no more devices to set up, highlight

EXIT and press ENTER or continue to set up additional A/V receiver audio/video sources.

Appendices

Appendix A: Programming the Remote Control . . . . . . . . . . . 58

Appendix B: Bypassing the Parental Lock . . . . . . . . . . . . . . 65

Appendix C: HDMI Control of CEC Devices . . . . . . . . . . . . . . 67

Appendix D: TV Care . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Appendix E: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 73

57

58

Appendices

Appendix A: Programming the Remote Control

This appendix explains programming the TV’s remote control to operate other A/V devices. This is distinct from NetCommand control.

Functions Available for Other A/V Devices

The TV’s remote control can be programmed to operate other types and brands of A/V products. The functions performed in each switch position vary depending on the product. Not all functions work for all models. The most common functions available are listed on this page.

ACTIVITY

GUIDE MENU INFO BACK

TV modes

To use the remote after programming, press the side button to change the control mode to match the device type.

The MORE Menus

The MORE key displays a menu showing additional key functions available for a device type after programming the remote control.

IMPORTANT

Some manufacturers may change their products or they may use more than one remote control system. The TV’s remote control may be unable to operate your A/V equipment in these cases.

VCRs and DVRs

• CHANNEL UP/DN

• POWER

SLEEP (from MORE menu)

(FAST FORWARD)

(PAUSE)

(PLAY)

(RECORD)

(REVERSE)

• (STOP)

GUIDE (DVR only)

MENU (DVR only)

0–9 Number Buttons

Mitsubishi VCRs are compatible with some additional keys.

Cable Boxes and Satellite Receivers

(not all functions for all models)

• PAGE UP/DOWN

• CANCEL

• CHANNEL UP/DN

• ENTER

• GUIDE

• POWER

LAST (ENTER; for channels on some models)

0–9 Number Keys

The record/playback keys:

(FAST FORWARD)

(PAUSE)

(PLAY)

(RECORD)

(REVERSE)

(STOP)

A/V Receivers

• MUTE

• POWER

SLEEP (from MORE menu)

• VOLUME

0–9 Number Buttons

• Direct Input Selection buttons: numbers and LAST (on some

Mitsubishi models)

CD Players

(not all functions for all models)

SLEEP (from MORE menu)

(FAST FORWARD)

(PAUSE)

(PLAY)

(REVERSE)

(STOP)

0–9 Number Buttons

DVD Players

(not all functions for all models)

CANCEL (on some models)

CHANNEL UP/DN (for track skip on some models)

• ENTER

• MENU

• POWER

SLEEP (from MORE menu)

(FAST FORWARD)

(PAUSE)

(PLAY)

(RECORD)

(REVERSE)

(STOP)

0-9 Number Keys

Appendices

59

Appendix A: Programming the Remote Control, continued

Programming the Remote Control

1.

Press the side button on the remote control to change to the correct mode for the product you want to control. Refer to the table below. Only one of each device type can be controlled in each mode.

Mode

CABLE/SAT

VCR

DVD

AUDIO

Affected Device

Cable Box

DTV Receiver

Satellite Receiver

VCR

DVR

DVD Player/Recorder

DVD Player/Recorder

DVR

VCR

A/V Receiver

Audio Amplifier

CD Player

2.

3.

4.

5.

6.

Press and hold POWER on the remote control for several seconds until the mode indicator blinks twice and goes off.

Release the POWER key.

Enter the first five-digit code listed for your equipment.

The mode indicator blinks twice when you start to enter the code and then once for each additional keypress.

The mode indicator blinks twice when you finish entering a valid code.

Point the remote control at the equipment and press POWER. If the product has no power on/off function, press a different key, such as (PLAY),

(STOP), VOLUME UP, or MUTE.

• If the equipment responds, the remote control is properly programmed.

If you need to start over or wish to exit programming mode, temporarily change to a different mode using the side button.

If the equipment does not respond, repeat steps 2–4 with the next five-digit code listed for your equipment.

Once you have found the correct code, write it in the space below for future reference.

Mode

CABLE/SAT

VCR

DVD

AUDIO

Device Type Code

IMPORTANT

You may need to reprogram the remote control after changing the batteries. Record the codes for each mode in the space provided to make this faster.

Code Verification

To determine the code programmed for any mode:

1.

Set the mode to the one you wish to verify.

2. Press and hold POWER on the remote control for several seconds until the mode indicator blinks twice and goes off.

3.

4.

Press keys 9 9 0

Press 1 and count the blinks of the power key.

Write down the number of blinks as the first digit of the code.

5.

Repeat step 4 for the second, third, fourth, and fifth digits of the code.

Audio Lock: Universal A/V Receiver

Control

With Audio Lock enabled, the remote control operates volume and mute on the A/V receiver in all modes set by the side button. Activate Audio Lock if you normally use an A/V receiver with your TV and other A/V equipment.

1.

2.

3.

Program AUDIO mode for your A/V receiver as described in “Programming the Remote Control” on this page.

With the remote control in AUDIO mode, hold POWER on the remote control for several seconds until the mode indicator blinks twice and goes off.

Press keys 9 9 3 ENTER

The mode indicator will blink twice to indicate Audio

Lock is active.

To Reset the Remote Control to Operate Volume and Mute for the TV Speakers

1.

2.

Press and hold POWER for several seconds until the mode indicator blinks twice and goes off.

Press keys 9 9 3 VOLUME UP.

The mode indicator will blink four times to indicate

Audio Lock has cleared.

60

Appendices

Appendix A: Programming the Remote Control, continued

Programming Codes

Audio Amplifiers

Adcom

Altec Lansing 41742

Bel Canto

41100, 40577

41583

Design

Bose

Carver

Cary Audio

40674

40892

41879

Design

Classe 41461

Flextronics 41879

Halcro

Harman/

41934

40892

Kardon

JVC

Krell

Left Coast

Lexicon

Marantz

Mark

40331

41837

40892

41802, 41145

40892

41483

Levinson

Parasound 41934

Philips 40892

Polk Audio 40892

Victor

Yamaha

40331

40354

Cable Boxes

A-Mark

ABC

Acorn

Action

Active

10144, 10008

10237, 10008

10237

10237

10237

Americast 10899

Amino

Archer

11822, 11602

10237

Bell South 10899

Century

Cisco

10008

11982, 11877, 10877

Comcast 11982

Digeo

Director

GE

General

12187

10476

10144

10476

Instrument

GoldStar 10144

Hitachi i3 Micro

Insight

Jerrold

10008

11602

10476

10476

Memorex 10000

Motorola 11376, 11254, 10476

Myrio 11822, 11602

Nova Vision 10008

Novaplex 10008

Pace 11877, 10877, 10237,

10008

Panasonic 11982, 10144, 10008,

10000

Cable Boxes

Paragon

Penney

Philips

Pioneer

10525, 10008, 10000

10000

11305

11877, 10877, 10533,

Pulsar

Quasar

Runco

Samsung 10144

Scientific

10144

10000

10000

10000

11877, 10877, 10477,

Atlanta

Sejin

Sony

Sprucer

Toshiba

US Elec-

10237, 10008, 10000

11602

11006

10144

10000

10008 tronics

Videoway 10000

Zenith 10899, 10525, 10000

CD Players

Acoustic 40420

Research

Akai

Burmester 40420

California

40083

40029

Audio Labs

DKK

Fisher

Garrard

Hafler

Harman/

Kardon

Inkel

Integra

JVC

Kenwood

40000

40000

40420

40173

41202, 40173, 40100,

40083

40180

40101

41294, 40072

40626, 40190, 40037,

KLH

Koss

LG

Magnavox 40038

Marantz

40029, 40000

41711, 41318

41317

41208

40626, 40435, 40180,

McIntosh

MCS

Memorex

MGA

40038, 40029

41703

40029

40420, 40000

Miro

40083

40000

Mitsubishi 40098, 40083

Modulaire 40420, 40180, 40087,

MTC

NAD

Onkyo

Optimus

40000

40420

41208

41327, 40101

40420, 40087, 40037,

40000

Panasonic 40752, 40388, 40029

CD Players

Parasound 40420

Penney

Philips

Pioneer

Proceed

Quasar 40029

RadioShack 40420, 40180, 40000

RCA

Realistic

40029

40626

41087

40420

40420

40420, 40180, 40087,

Roksan

Rotel

Sansui

Sanyo

40000

40435

40420

40000

Sharp

40087, 40000

Sherwood 41950, 40180

Sony

40180, 40037

41364, 40490, 40185,

40100, 40000

Symphonic 40180

Tascam

TDK

Teac

Technics

Victor

Wards

Yamaha

Yorx

40420

41208

40490, 40420, 40180

40029

40072

40087

41292, 40490, 40036

40000

A/V Receivers

ADC

Aiwa

40531

41641, 41405, 41388,

Alco

AMC

Anam

Arcam

41243, 40189, 40121

41390

41077

41609, 41074

41189

Audiotronic 41189

Audiovox

Bose

41390

41933, 41841, 41629,

Cairn

41253, 41229, 40639

Capetronic 40531

Carver

40189

41289, 41189, 40189,

Curtis

40121

40014

Mathes

Daewoo

Denon

Emerson

Fisher

Grundig

Harman/

Kardon

Hitachi

Insignia

41250

41360, 41306, 41142,

40121

40531

41801

40189

41306, 41304, 41289,

40891, 40189, 40110

41801

42169, 41893, 41077,

41030

Appendices

61

Appendix A: Programming the Remote Control, continued

Programming Codes, continued

A/V Receivers

Integra 41805, 41320, 41298,

JBL

JVC

40842

41306, 40110

42331, 41643, 41495,

Kawasaki

Kenwood

KLH

LG

41374, 41282, 41058

41390

41570, 41569, 41313

41428, 41390

Linn

42197, 41293

40189

Magnavox 41514, 41269, 41266,

Marantz

41189, 40531, 40189

41289, 41269, 41189,

McIntosh

40891, 40189

41289

Micromega 41189, 40189

Mitsubishi 41957, 41922, 41921,

Myryad

41920, 41393

Nakamichi 41313

Onkyo

41189

41905, 41805, 41320,

Optimus

41298, 40842

41074, 41023, 40531,

40121, 40014

Panasonic 42967, 41764, 41763,

41633, 41548, 41518,

41509, 41316, 41308,

Philips

Pioneer

41288, 41275

41269, 41266, 41189,

40891, 40531, 40189

41935, 41384, 41123,

41023, 40630, 40531,

Polaroid

40150, 40014

41508

Polk Audio 41289, 40189

Proscan 41254

RadioShack 41609

RCA 41609, 41511, 41390,

41254, 41123, 41074,

Realistic

Revox

Rio

Samsung

41023, 40531

41609, 40121

40189

41869

Sansui

Sanyo

41500, 41304, 41295

41189, 40189

41801

Sherwood 42169, 41905, 41077

Sherwood 42169

Newcastle

Sonic Blue 41869

Sony 41858, 41822, 41759,

41758, 41658, 41622,

41558, 41441, 41382,

41258, 41131, 41058

Stereophonics 41023

Sunfire

Teac

41313

41390, 41074

A/V Receivers

Technics

Thorens

Toshiba

Venturer

Wards

Yamaha

41518, 41308

41189

41788, 41123, 40842

41390

40189, 40014

41815, 41476, 41376,

YBA

Zenith

41375, 41331, 41276,

41176, 41023, 40176

41921

41293

Satellite Receivers

Bell ExpressVu 11170, 10775

Chaparral 10216

Crossdigital 11109

DirecTV 11856, 11749, 11640,

11639, 11609, 11442,

11414, 11392, 11377,

Dish

Network

11142, 11109, 10819,

10749, 10639, 10566,

10392, 10247, 10099

11775, 11505, 11170,

10775

System

Dishpro 11775, 11505, 10775

Echostar 11775, 11505, 11170,

10775

Expressvu 11775, 10775

Fortec Star 11821

Funai

GE

GOI

Hitachi

Houston

HTS

Hughes

11377

10566

11775, 10775

11250, 10819, 10749

10775

11775, 10775

11749, 11442, 11142,

Network 10749

Systems

Humax

Innova

JVC

11790, 11781

10099

11775, 11170, 10775

11414 LG

Magnavox 10722

Mitsubishi 10749

Netsat 10099

Panasonic 10701, 10247

Pansat

Philips

11807

11749, 11442, 11142,

10775, 10749, 10722,

Proscan

10099

RadioShack 10775, 10566

RCA

10566, 10392

11442, 11392, 11142,

10855, 10775, 10566,

10392, 10143

Samsung 11609, 11442, 11377,

11276, 11142, 11109

Satellite Receivers

SKY

Sony

Tivo

Toshiba

10099

11640, 11639, 10639

Thomson 10566, 10392

UltimateTV 11640, 11392

Uniden

Zenith

11442, 11142

11749, 10790, 10749

10722

11856, 11810

VCRs

A-Mark 20278, 20046, 20037,

ABS

20000

Accurian 20000

Admiral

21972

20479, 20209, 20060,

20048, 20047, 20039

Adventura 20037, 20000

Aiko

Aiwa

Akai

Alba

20278

20124, 20037, 20000

20242, 20175

20278, 20209

Alienware 21972

Allegro

America

20039

20278

Action

American 20081, 20035

High

Amstrad

Astra

20000

20035

Audiovox 20278, 20038, 20037

Avis

Bell &

20000

20479, 20048, 20046,

Howell

Bell

20039, 20035, 20000

21944

ExpressVu

Broksonic 20479, 20209, 20184,

Calix

Candle

Canon

Carver

CCE

Cineral

Citizen

20121

20037

20038, 20037

20035

20081, 20035

20278

20278

20479, 20278, 20209,

Classic

20037, 20035, 20000

20037

Colortyme 20278, 20060, 20045,

Colt

Craig

Criterion

Crosley

Crown

Curtis

20035

20000

20047, 20037

20000

20081, 20035, 20000

20278

20432, 20278, 20162,

Mathes 20060, 20035, 20000

CyberPower 21972

Daewoo 20278, 20046, 20045,

20037

62

Appendices

Appendix A: Programming the Remote Control, continued

Programming Codes, continued

VCRs

Daytron

Dell

Denon

DirecTV

Dish

Network

20278, 20037

21972

20081, 20042

20739

21944

System

Dishpro

Dual

21944

20000

Durabrand 20039, 20038

Dynatech 20000

Echostar 21944

Electrohome 20209, 20060, 20043,

20037, 20000

Electrophonic 20037

Emerald

Emerex

Emerson

20184, 20121

20032

21593, 20593, 20479,

20278, 20209, 20184,

20121, 20043, 20037,

20000

Expressvu 21944

Fisher 20047, 20046, 20039,

Fuji

Fujitsu

Funai

20000

20035, 20033

20000

21593, 20593, 20278,

Garrard

Gateway

GE

20037, 20000

20000

21972

20060, 20048, 20035,

Gemini

Genexxa

20000

GFM

Go Video 20614, 20432

GOI

GoldStar

20060

20278, 20037, 20000

21593

21944

20278, 20039, 20038,

20037, 20035, 20000

Goodmans 20278, 20081, 20037,

20000

Gradiente 20000

Granada

Grundig

Harley

20081, 20042

20081

20000

Davidson

Harman/ 20081, 20075, 20038

Kardon

Headquarter 20046

Hewlett 21972

Packard

HI-Q

Hitachi

Howard

Computers

HP

20047, 20035, 20000

20089, 20045, 20042,

20037, 20035, 20000

21972

21972

VCRs

HTS

Hughes

Network

21944

20739, 20042

Systems

Humax

Hush

Hytek

21988, 21797, 20739

21972

20047, 20000 iBUYPOWER 21972

Instant 20035

Replay

Jensen

JVC

KEC

20067

21944, 20067

20278, 20037

Kenwood 20067, 20046, 20038

Kodak

KTV

LG

Linksys

20037, 20035

20000

20038, 20037

21972

Lloyd’s

Loewe

20038, 20000

20081

Logik 20000

Lumatron 20278

Luxor

LXI

20046

20067, 20042, 20037,

20000

Magnasonic 20593, 20278, 20037,

20000

Magnavox 21593, 20618, 20593,

20563, 20081, 20048,

20039, 20037, 20035,

Marantz

Marta

Matsui

Matsushita 20162, 20081, 20035

Media

20000

20081, 20038, 20035

20037

20209, 20037

21972

Center PC

MEI 20035

Memorex 20479, 20278, 20209,

20162, 20048, 20047,

20046, 20039, 20037,

Metz

MGA

20035, 20000

20037

20060, 20043

Microsoft 21972

Mind

Minolta

21972

20042

Mitsubishi 20443, 20242, 20214,

20173, 20075, 20067,

20060, 20048, 20047,

20043, 20042, 20000

Motorola 20048, 20035

MTC

MTX

Multitech 20039, 20000

NEC

Nikko

20000

20000

20067, 20038

20278, 20037

VCRs

Nikkodo

Niveus

20278, 20037

21972

Media

Northgate 21972

Olympus

Onkyo

Optimus

20162, 20035

20222

21062, 21048, 20593,

Penney

20432, 20162, 20048,

20047, 20037, 20035,

Orion

20000

20479, 20278, 20209,

Panama

20184, 20121, 20000

20035

Panasonic 21062, 20616, 20614,

20225, 20162, 20035,

20000

20162, 20081, 20067,

20047, 20042, 20038,

Pentax

Philco

Philips

20037, 20035, 20000

20042

20479, 20209, 20081,

20035, 20000

21181, 21081, 20739,

20618, 20616, 20209,

20162, 20081, 20048,

Pilot

Pioneer

20045, 20035, 20000

20037

20162, 20081, 20067,

20042

Polk Audio 20081

Portland 20278

Presidian 21593

Proscan

Protec

Pulsar

Quarter

Quartz

Quasar

20060

20000

20278, 20039

20046

20047, 20046, 20035

20162, 20035

RadioShack 20162, 20048, 20047,

Radix

Randex

RCA

Realistic

20046, 20037, 20035,

20000

20037

20037

20880, 20060, 20048,

20045, 20042, 20035,

20000

20278, 20162, 20121,

20048, 20047, 20046,

20037, 20035, 20000

ReplayTV 20616, 20614

Ricavision 21972

Runco

Salora

20039

20075

Samsung 20739, 20432, 20060,

Sanky

20045, 20038, 20000

20048, 20039

Appendices

63

Appendix A: Programming the Remote Control, continued

Programming Codes, continued

VCRs

Sansui

Sanyo

Scott

Sears

20479, 20209, 20067,

20000

20479, 20159, 20047,

20046, 20000

20184, 20121, 20045,

20043

20209, 20162, 20067,

20060, 20048, 20047,

20046, 20045, 20043,

Sharp

20042, 20039, 20037,

20035, 20033, 20000

20848, 20048, 20047,

Shintom

Siemens

20032, 20000

20039, 20000

20037

Signature 20479, 20060, 20048,

20046, 20037, 20035,

Singer

20000

20037

Sonic Blue 20616, 20614

Sonographe 20046

Sony 21972, 21032, 20636,

20067, 20047, 20046,

20035, 20033, 20032,

20000

Soundmaster 20000

Stack 9

STS

SV2000

SVA

Sylvania

21972

20042

20000

20000

21593, 20593, 20081,

20043, 20035, 20000

Symphonic 21593, 20593, 20000

Systemax 21972

Tagar 21972

Systems

Tandy

Tashiko

Tatung

20000

20037

20081, 20067, 20048,

Teac

20000

20067, 20000

Technics 20162, 20037, 20035,

Teknika

Tevion

20000

Thomas

Thomson 20060

Tisonic

Tivo

20037, 20035, 20000

20479

20000

20278

21944, 20739, 20636,

TMK

TNIX

Toshiba

20618

20000

20037

21988, 21972, 21008,

20209, 20045, 20043,

Tosonic

20000

20278

Totevision 20037

VCRs

Touch

Trix

Ultra

Vector

Vector

Research

Victor

Video Con-

21972

20037

20278, 20045

20045

20184, 20038

20067

20242, 20045 cepts

Videomagic 20037

Videosonic 20000

Viewsonic 21972

Villain

Voodoo

Wards

20000

21972

20479, 20081, 20060,

20048, 20047, 20046,

20045, 20043, 20042,

20038, 20037, 20035,

20033, 20000

Wharfedale 20593

White 20479, 20278, 20209,

Westinghouse

World

XR-1000

Yamaha

Zenith

20000

20479, 20209

20035, 20000

20038

21139, 20479, 20278,

20209, 20039, 20037,

20033, 20000

ZT Group 21972

DVD and Blu-ray Players

3D LAB

Accurian 31416, 30675

Acoustic

30539, 30503

30730

Solutions

Adcom

Afreey

Aiwa

Akai

31094

30698

30641, 30533

31089, 30770, 30705,

Alba

Alco

Allegro

Amphion

Media

30695

30717, 30672

30790

30869

30872

Works

AMW 30872

Apex Digital 31061, 31056, 31020,

31004, 30797, 30796,

30794, 30755, 30717,

Arrgo

Aspire

30672, 30533

31023

31168, 31407

Digital

Astar

Audiovox 31041, 30790, 30717

Awa

31489

30730

DVD and Blu-ray Players

B & K

BBK

Bel Canto

30662, 30655

31224

31571

Design

Blaupunkt 30717

Blue Parade 30571

Blue Sky 30699, 30695

Bose

Brandt

32023, 31895

30651

Broksonic 30695

California 30490

Audio Labs

Celestial

Centrex

Cinea

31020

31004, 30672

30831

CineVision 30869, 30833

Citizen 32116, 31587, 31277,

31003, 30695

Clairtone 30571

Coby 31351, 31177, 31165,

31107, 31086, 31077,

Craig

Creative

Curtis

30852, 30778

30831

30539, 30503

31087

Mathes

CyberHome 31537, 31502, 31129,

31117, 31024, 31023,

Cytron

Daewoo

30874, 30816

30705

31242, 31234, 31172,

31169, 30869, 30833,

Dansai

Daytek

Decca

Denon

30784, 30770, 30705

30770

30872

30770

Denver

Desay

32258, 30634, 30490

30778

31407

DigitalMax 31738

Digitrex

Disney

DiViDo

Dual

30672

31270, 30675

30705

31068, 30675

Durabrand 31127, 31023

DVD2000 30521

Electrohome 32116, 31003

Emerson 31268, 30675, 30591

Enterprise 30591

Entivo

Enzer

ESA

Firstline

Fisher

Funai

Gateway

GE

30539, 30503

30770

31268

30651

30670

31268, 30675

31158, 31077, 31073

30815, 30717, 30522

64

Appendices

Appendix A: Programming the Remote Control, continued

DVD and Blu-ray Players

GFM 31268, 30675

Go Video 31730, 31304, 31158,

31144, 31099, 31075,

31044, 30869, 30833,

30783, 30744, 30741,

30717, 30715, 30573

GoldStar 30869, 30741

Goodmans 30790

GPX 30769, 30699

Gradiente 30651, 30490

Greenhill 30717

Grundig

Harman/

30705, 30539

30702, 30582

Kardon

Hello Kitty 30831

Hitachi

Hiteker

Humax iLo

Initial

Insignia

Integra

IRT

JBL

JMB

JSI

JVC

30664, 30573

30672

31588, 31500

31348

30717

32095, 31268, 30675

31769, 30627, 30571

30783

30702

30695

31423

31550, 31275, 31164, jWin

30867, 30623, 30558

31049

Kawasaki 30790

Kenwood 30534, 30490

KLH 31149, 31020, 30790,

Kloss

Koss

30717

30533

31423, 31061, 30769,

Lasonic

Lecson

Lenoxx

LG

LiteOn

30651

30798, 30627

31533

31127

30869, 30741, 30591

31738, 31656, 31440,

Loewe

Logix

31416, 31158, 31058

30741, 30511

30783

Magnasonic 30675, 30651

Magnavox 31506, 31354, 31268,

30675, 30646, 30539,

Marantz

30503

30675, 30539, 30503

McIntosh 31533, 31273

Medion 30651

Memorex 31270, 30831, 30695

Microsoft 32083, 30522

Minato

Mintek

30752

Mitsubishi 31521, 30521

Mustek

30839, 30717

30730

Programming Codes, continued

DVD and Blu-ray Players

Myryad

NAD

Naiko

NEC

Nesa

30894

30741

30770

30869, 30785

30717

NexxTech 31402

Norcent 31265, 31107, 31003,

Onkyo

Oppo

Optimus

Oritron

30872

31769, 30627, 30503

31224, 30575

30571

Palsonic

30651

30852, 30672

Panasonic 31762, 31641, 30703,

Philco

Philips

30632, 30571, 30503,

30490

30675

32084, 32056, 31506,

31354, 31340, 31267,

31158, 30675, 30646,

30539, 30503

Phonotrend 30699

PianoDisc 31024

Pioneer 31571, 31512, 31460,

30632, 30631, 30571,

Polaroid

30525, 30142

31086, 31061, 31020

Polk Audio 30539

Portland 30770

Presidian 31738, 30675

Proceed

Proscan

30672

30522

Prosonic 30699

ProVision 30778

Qwestar 30651

Radionette 30741

RadioShack 30571

RCA 31769, 30822, 30790,

Realistic

Reoc

Revoy

Rio

Rotel

Rowa

Saba

Sampo

30717, 30571, 30522

30571

30752

30699

30869

31178, 30623

31004

30651

30752, 30698

Samsung 31075, 31044, 30820,

Sansui

Sanyo

30744, 30573, 30490,

30199

30695

30873, 30695, 30675,

30670

Schneider 30783

Schwaiger 30752

Sensory 31158

Science

DVD and Blu-ray Players

Sharp 32250, 31256, 30752,

Sharper

30675, 30630

31117

Image

Sherwood 31077, 31043, 30770,

Sherwood

30633

31077

Newcastle

Shinsonic 30839, 30533

Slim Art

SM Elec-

30784

30730 tronic

Sonic Blue 31099, 30869, 30783,

Sony

30715, 30573

31536, 31533, 31516,

31431, 31070, 31033,

Sungale

SVA

Sylvania

Symphonic 31268, 30675

TAG

30864, 30533

31074

30860, 30717

31268, 30675

30894

McLaren

Tatung

Teac

30770

30790, 30717, 30571

Technics 30703, 30490

Technika 30770

Technosonic 30730

Tevion 30651

Theta Digital 30571

Thomson 30522, 30511

Tivo

Toshiba

31588, 31512, 31503

31769, 31608, 31588,

31515, 31510, 31503,

31154, 30695, 30573,

Tredex

Unimax

United

Universum 30591

Urban Con-

30539, 30503

30800

30770

30730

30539, 30503 cepts

US Logic 30839

V

Venturer

Vizio

Wesder

Xbox

Yamaha

31226, 31064

30790

31226, 31064

30699

32083, 30522

30646, 30545, 30539,

30497, 30490

Yamakawa 30872

Zenith 30869, 30741, 30591,

Zeus

Zoece

30503

30784

31265

Appendix B: Bypassing the Parental Lock

IMPORTANT

Cut along the dotted line and file bypass instructions in a safe place for future reference.

Appendices

Mitsubishi Home Theater TV

C9 Series

737 Series

837 Series

65

Bypassing the Parental Lock

After you set the lock, you must use your pass code to:

• View a locked program

View the locked TV

Cancel the lock

Enter the Lock menus

If you forget your pass code, you can view the locked

TV without entering your pass code. When prompted for the pass code, press the number 9 and

(LAST) keys on the TV remote control at the same time. This process temporarily unlocks the TV.

When entering the Lock menu, you are prompted to enter a pass code.

• To change the pass code, press 9 and

(LAST) at the same time. Either enter a new pass code to open the Lock menu and make changes or press

BACK to close the menu.

• If any of the locks are turned on and you exit the menus when prompted for a new code, the old code and all lock settings are retained.

• If all locks are turned off and you exit the menus when prompted for a new code, then the previous code is erased.

IMPORTANT

When changing or deleting your pass code, you must use the remote control included with this TV. You cannot use a Mitsubishi remote control from another component or a

“universal” remote.

66

Appendices

This page intentionally left blank

Appendices

67

Appendix C: HDMI Control of CEC Devices

Many new HDMI devices have a feature called Consumer Electronics Control (CEC) or HDMI Control.

HDMI Control allows one device, such as the TV, to control other devices, such as an A/V receiver or disc player. Use of CEC is optional.

Each manufacturer chooses which CEC functions to support so it is difficult to predict which devices and features are compatible with Mitsubishi’s HDMI Control.

You may find that CEC functions for a specific device are limited.

To use HDMI Control, you must enable it in both the TV and the device.

• In the TV.

Enable HDMI control from the New

Device Found screen or from the Inputs > HDMI

Control menu.

• I n the Device. Most devices with HDMI CEC compatibility let you turn it on or off in the device menus, where it is typically listed as “HDMI Control.”

Enabling HDMI Control of CEC Devices

To ensure proper detection

• Power on HDMI devices before connecting them to

• the TV.

Connect and set up HDMI devices one at a time.

1.

2.

3.

Power on the device and allow it to complete the power-on sequence (boot up). Stop any playback.

Connect the device to one of the TV’s HDMI inputs.

When the TV detects the connection, the New

Device Found screen will appear.

Note: See “If the New Device Found Screen Displays

No HDMI Control Option” on this page if there is no HDMI Control option.

New Device Found screen with HDMI Control option.

This screen displays only if the device’s HDMI Control is enabled.

4. If prompted for a name, highlight the name you want to assign the device.

5. Highlight On.

7. Highlight EXIT and press ENTER to close the New

Device Found screen.

Note: At any time after completing Auto Input Sensing, you can set the TV’s HDMI control on or off in the Inputs > HDMI Control menu.

8. 837 Series.

To supplement HDMI control with

NetCommand IR control, see page 45.

If the New Device Found Screen

Displays No HDMI Control Option

If the New Device Found screen shows no option for

HDMI Control, one of these conditions applies:

• HDMI Control is turned off in the menus of the new device

Action: a. b.

Highlight EXIT and press ENTER to close the

New Device Found screen.

Display the device’s setup menus and enable the device’s CEC capabilities.

c. d.

Wait for the TV’s New Device Found screen to appear again.

If the New Device Found screen does not appear, power off the device. Power on the device and wait for the New Device Found screen to display with the HDMI Control option.

The device does not have CEC compatibility

Action:

-

-

Control the device with its own remote control or program the TV’s remote control to operate the device.

837 Series.

Use the TV’s NetCommand IR control (page 45).

68

Appendices

Appendix C: HDMI Control of CEC Devices, continued

HDMI Control of an HDMI A/V

Receiver and Connected Devices

Note: Connect the A/V receiver to the TV with an

HDMI cable before making other connections.

1.

2.

3.

4.

5.

Enable HDMI Control for the A/V receiver as described in “Enabling HDMI Control of CEC

Devices” on the previous page.

Power on the HDMI device you wish to connect to the A/V receiver (such as a disc player, cable box, or satellite receiver). Allow the device to complete the power-on sequence (boot up). Stop playback if the device starts playing.

Connect the device to the A/V receiver with an

HDMI cable.

Select the device’s HDMI input on the A/V receiver’s front panel controls or remote control.

When the TV detects the connection, the New

Device Found screen will appear.

Note: If the TV is unable to detect the device, either the device’s CEC capability is not enabled or the device is not CEC compatible. Enable

HDMI control through the device’s menus before continuing. You may need to temporarily connect the device directly to the TV to view device menus.

6. Highlight On.

Optional digital audio connection ANT 2 / AUX

ANT 1 / MAIN

3D

GLASSES

EMITTER

L

AUDIO

OUTPUT

DVI/PC

R

AUDIO

INPUT

L

R AUDIO L VIDEO

Y Pb Pr

R

Y/ VIDEO Pb Pr

DIGITAL

OUTPUT

R

AUDIO L

(480i / 480p / 720p / 1080i)

IR-

Output / External

Controller Input

R

HDMI

AUDIO: PCM STEREO

TV back panel

HDMI OUT

A/V receiver with

HDMI output

High-definition

DVD player

Cable box

VCR

DVD player

Connecting HDMI devices. The optional digital audio connection allows you to hear audio through the A/V receiver from devices connected to the TV only.

7.

8.

Highlight EXIT and press ENTER to close the New

Device Found screen.

Optional: Connect the TV’s DIGITAL AUDIO

OUTPUT to an input on the A/V receiver. Use this additional connection if:

• You want the ability to switch between the A/V receiver speakers and the TV speakers.

• You want to use the A/V receiver to listen to devices connected to the TV only, e.g., an antenna input or camcorder.

9. 837 Series.

If desired, perform NetCommand IR

Learning to supplement CEC functions. You must first connect and place IR emitters for the devices.

See page 45.

Appendices

69

Appendix C: HDMI Control of CEC Devices, continued

Resolving CEC Conflicts

Because each manufacturer selects which CEC functions to support, some devices can conflict with other devices. If control conflicts arise, you can:

• Turn off TV control of an individual CEC-enabled device (see below).

• Turn off CEC in the setup menu of one of the devices.

Turning Off the TV’s HDMI Control of a CEC Device

1.

2.

3.

4.

Press MENU on the TV remote control.

Highlight Inputs > HDMI Control and press ENTER to open the menu.

Move to the device name and press to select

Off to turn off the TV’s ability to control the device.

Press MENU to clear the menu.

Inputs > HDMI Control menu

Removing an HDMI Device

1.

2.

3.

Power off the device.

Disconnect the HDMI cable.

Press MENU on the TV remote control to enter the

TV main menu.

4.

Highlight Inputs > Name and press ENTER to open the menu.

5.

6.

Select Delete from the HDMI input names.

Press MENU to clear the menus.

Using HDMI Control

As an example of using HDMI Control, press PLAY on the device itself to:

Power on the TV

Switch to the device (no need to display the

Activity menu)

Begin play of the device

Direct Keys

Test your equipment with the TV’s remote control to find additional supported commands. See the table below for commands that may be available, depending on the individual device.

CEC-enabled VCR, DVD, and DVR functions that may be available:

Record/

Playback

Menu

Navigation

Channel Tuning

CHANNEL UP/DN

Other

GUIDE

ENTER

CANCEL

(to cancel)

Digits 0–9, CANCEL

ENTER

MENU

If you have a CEC-enabled A/V receiver, CEC-enabled devices connected to the A/V receiver with an HDMI cable may also be controllable. They can be selected from the TV’s Activity menu.

CEC-enabled A/V receiver functions that may be available:

Try the VOLUME UP/DOWN, MUTE, and menu-navigation keys.

To open the A/V receiver menu, follow these steps:

1.

2.

3.

4.

While watching TV, press MORE then 9 (AUDIO).

Press

Press

Press MORE and then 1 (MENU) to display the menu.

until the Speakers option displays.

to select AVR as the source.

The MORE Menu

Press MORE on the TV’s remote control to see a menu of additional supported functions for the current

CEC-enabled device. To issue a command, press the number key indicated in the menu.

Inputs > Name menu with Delete selected for HDMI-3.

MORE key: Sample menu for a CEC-enabled DVD player

70

Appendices

Appendix D: TV Care

Lamp-Cartridge Replacement and Cleaning

CAUTION: If the television is on, press POWER to turn it off. Unplug the television and allow it to cool for at least one hour before attempting to replace the lamp cartridge.

Lamp

The light source for this television is a lamp, which is part of a lamp cartridge assembly. The life of the lamp can vary, based on the lamp itself, the air temperature around the TV while it is operating, the selected lamp mode, and your viewing patterns. Warmer air or poor ventilation shorten the lamp life, as does use of the Bright lamp mode

BURN DANGER! HOT SURFACES INSIDE!

Touch lamp cartridge handle only. Do not touch lamp or lamp cartridge housing. Keep lamp cartridge horizontal during removal. Do not tilt as glass may come out and cause injury. Replace lamp cartridge only with the same part number 915B403001.

and turning the television on and off frequently. Mitsubishi warrants the lamp for one (1) year from the date of original TV purchase at retail.

WARNING

THE ACCESS PANEL IS

To Order a New Lamp

To Receive a Replacement Lamp Under Warranty

• Visit our website at www.mitsuparts.com.

• Call (800) 553-7278. Please have model number, serial number, and TV purchase date available.

Important: All lamps replaced under warranty must be returned to

Mitsubishi where they will be inspected for defect verification.

CAUTION

PROVIDED WITH AN INTERLOCK

TO REDUCE THE RISK OF

EXCESSIVE ULTRAVIOLET

RADIATION. DO NOT DEFEAT

ITS PURPOSE OR ATTEMPT TO

SERVICE WITHOUT REMOVING

PANEL COMPLETELY.

To Purchase a Replacement Lamp After Warranty

Visit our website at www.mitsuparts.com or call (800) 553-7278. Order the following:

Lamp Part Number 915B403001

Lamp-Substitution Alert

MDEA recommends that you use only genuine Replacement Lamp Assemblies purchased directly from Mitsubishi or a

Mitsubishi Authorized Dealer or Mitsubishi Authorized Service Center. MDEA advises that replacement lamps obtained separately from the Lamp Cartridge and/or Lamp Assemblies obtained from unauthorized sellers may be incorrect for your television, may not fit or perform properly and may even damage your television. MDEA can not be responsible for the performance, reliability or safety of any replacement lamps that are obtained from unauthorized sources.

WARNING

• Do not remove the lamp cartridge immediately after turning off the television. You may get burned because the lamp is very hot. Allow the television to cool for at least one hour before replacing the lamp cartridge.

• Do not remove the lamp cartridge except when replacing it. Careless treatment can result in injury or fire.

• Do not touch the lamp glass element. It may be very hot and break, causing injuries or burns.

• Be sure not to insert any metal or flammable object into the lamp cartridge opening, as it may cause fire or electrical shock. If a foreign object is inserted into the opening, unplug the AC cord of the TV and contact your dealer for service.

• Install the lamp cartridge securely. Failure to do so may cause a fire.

• Do not touch the lamp glass elements. Oils from your fingers may cause premature lamp failure.

Hg = MERCURY

THE LAMP INSIDE THIS PRODUCT CONTAINS MERCURY AND MUST BE RECYCLED OR

DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance at www.eiae.org

Appendix D: TV Care, continued

Lamp-Cartridge Replacement

Removing the Old Lamp Cartridge

1. Turn off TV power and unplug the TV. Allow the lamp to cool for at least one hour before proceeding.

2. After the lamp has cooled, remove the cover of the lamp compartment, located on the back of the TV.

Refer to figures 1 and 2. Use a #2 (medium) Phillips screwdriver to loosen the screw securing the cover.

Keep the screw and cover for re-installation

3. Wi th a medium Phillips screwdriver, loosen the two screws securing the lamp cartridge until they disengage from the mating threads. These are captive screws and cannot be separated from the lamp cartridge.

4. Fully open the bag supplied with the replacement lamp and set the opened bag aside.

5. Gently grasp the handle of the lamp cartridge and pull the old cartridge straight out. See figure 3.

6.

CAUTION: Do not tilt or rotate the cartridge, as small glass fragments may fall out.

Without tilting or putting down the lamp cartridge, insert it into the opened bag. Close the bag while being careful not to let any glass particles fall out.

Installing the New Lamp Cartridge

1. Do not touch the glass parts of the new lamp cartridge. Insert the new cartridge into the TV in the same orientation as the old cartridge. Push on the cartridge housing until it is fully seated.

2. Gently tighten the screws with the screwdriver.

AVOID OVERTIGHTENING!

3.

4.

Replace the plastic cover and retaining screws.

WASH YOUR HANDS THOROUGHLY, AS THIS

LAMP CONTAINS MERCURY.

Disposal of the Old Lamp Cartridge

Lamp under warranty: All lamps replaced under warranty must be returned to Mitsubishi. Use the return shipping label provided and send to Mitsubishi Digital

Electronics, America, 625 Braselton Parkway, Suite 200,

Braselton, GA 30517.

IMPORTANT: Lamps found to be without defect will be returned and charged back to the sender.

Lamp no longer under warranty: Contact your local authorities or the Electronic Industries Alliance at www.eiae.org for lamp-disposal or recycling instructions.

Do not dispose of the old lamp with common trash.

Appendices

Figure 2

Figure 1

Figure 3

Use only replacement lamp part number

915B403001 .

71

Lamp-Cartridge Filter Cleaning

If the TV shuts off after displaying the message “TV will shut down in a few seconds. Please check if the air flow is blocked” and/or the STATUS LED is yellow, the air filter may need cleaning. The air filter is part of the lamp cartridge. Use the following procedure to clean the filter.

1. Remove the lamp cartridge from the TV as described under “Removing the Old Lamp Cartridge.” Do not tilt or rotate the cartridge. Do not touch the glass parts of the lamp cartridge.

2. Holding the lamp cartridge horizontal (do not tilt or rotate), use a soft dry brush or vacuum cleaner to remove any dust that may be present on the mesh filter. Do not use liquids. See figure 4.

3. Reinstall the lamp cartridge as described under

“Installing the New Lamp Cartridge.”

Figure 4

Keep lamp cartridge horizontal and remove dust from the mesh filter using a vacuum cleaner or soft dry brush.

72

Appendices

Appendix D: TV Care, continued

Cleaning Recommendations

Normally, light dusting with a dry, non-scratching duster will keep your TV clean. If cleaning beyond this is needed, please use the following guidelines:

First, turn off the TV and unplug the power cord from the power outlet.

Occasionally clean dust build-up from the air-intake grilles on the back and sides of the TV. Clean using a vacuum cleaner with a brush attachment.

Top and Sides of the TV

Gently wipe down your TV with a soft, non-abrasive cloth such as cotton flannel, microfiber, or a clean cloth diaper, lightly moistened with water. Dry with a second dry, soft, non-abrasive cloth.

For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent, to the water used to moisten the cloth. Rinse with a second cloth moistened only with water. Dry with a third dry, soft, non-abrasive cloth.

Screen

Follow the instructions for the top and sides, wiping gently in an up and down motion.

Clean the entire screen evenly, not just sections of the screen.

Do not allow liquid to drip down the screen, as some liquid may enter the TV through the gap between the screen and screen frame.

You may purchase Mitsubishi Screen Cleaner, part number CLEANER-VSS, by calling (800) 553-7278.

General Cleaning Precautions

DO NOT allow liquid to enter the TV through the ventilation slots or any crevice.

DO NOT use any strong or abrasive cleaners, as these can scratch the surfaces.

DO NOT use any cleaners containing ammonia, bleach, alcohol, benzene, or thinners, as these can dull the surfaces.

DO NOT spray liquids or cleaners directly on the

TV’s surfaces.

DO NOT scrub or rub the TV harshly. Wipe it gently.

Care of the Remote Control

Remote Control Tips

For longer life, use alkaline batteries.

Do not mix old and new batteries.

Be within 20 feet of the equipment.

Do not press two or more keys at the same time unless instructed to do so.

Do not allow the unit to get wet or become heated.

Keep the unit out of direct sunlight.

Avoid dropping on hard surfaces.

Do not use harsh chemicals to clean. Use only a soft, lightly moistened cloth.

Resetting the Remote Control

If TV mode is selected and the TV does not respond properly, reset the remote control.

1.

Press and hold POWER for several seconds until the mode indicator blinks twice and goes off.

2.

3.

Release the POWER key.

Press keys 0 0 9 3 5 and the mode indicator will blink twice when you finish entering the code.

When entering the code, pause for a moment between each key press to ensure it is recognized.

Low-Battery Indicator

If you press a key and the mode indicator blinks five times, replace the remote control’s batteries.

Appendices

73

Appendix E: Troubleshooting

TV Reset Comparison Guide

You can resolve many common TV problems using the reset functions described in the following table.

See also the troubleshooting suggestions later in this appendix.

IMPORTANT

Before you change sound or picture settings: If picture or sound settings seem wrong for a broadcast channel (a channel from the ANT input, a cable box, or satellite receiver), first check other channels from the same input before changing settings. If most other channels from the same input seem correct, there is likely a problem with the broadcast rather than with the

TV. Use care in this case, as changes you make to fix problems on individual channels also affect all other channels on the same input.

Reset Name

Format

PerfectColor™

Reset or

PerfectColor™/

PerfecTint™

Reset (837

Series)

(for the single input currently being watched)

When to Use

When the picture shape seems incorrect, use

MORE > 0 (FORMAT) to change the shape of the picture.

When the color intensities seem out of balance, use the

PerfectColor/PerfecTint reset to reset the color balances to the original factory settings.

Both PerfectColor and

PerfecTint are reset at the same time.

1.

2.

3.

How to Use

Press the MORE key and then repeatedly press 0 (FORMAT) to cycle through the available aspect ratios.

While viewing the input to be reset, press go to

PerfectColor.

Press

PerfectColor adjustment screen.

Press

MENU and

Adjust > Picture+ >

ENTER to display the

CANCEL to reset the colors.

Resulting Action

The last-used format for a signal type is memorized for each input.

The next time the same input and the same signal type is viewed, the last-used format will be recalled.

All PerfectColor/PerfecTint sliders are reset to the original center position. The PefectColor/

PerfecTint settings for other inputs remain unchanged.

A/V Memory

Reset

(for the single input currently being watched)

When audio and/ or video settings for a single input seem incorrect, use A/V

Memory Reset to return the input to the original factory settings.

1.

2.

3.

While viewing the input to reset, press MENU and go to Adjust >

Reset.

Press ENTER to highlight the

Reset icon.

Press ENTER again to reset.

All Audio and Video settings for the individual input are reset except for the Listen To,

Language, audio Balance,

Closed Caption, and Advanced

Picture settings.

Service and Customer Support

Service

If you are unable to correct a problem with your TV, consult your Mitsubishi dealer or Mitsubishi Consumer Relations at (800) 332-2119.

• DO NOT adjust any controls other than those described in this Owner’s Guide.

• DO NOT remove the protective back cover of your TV.

Customer Support

• To order replacement or additional remote controls or lamp cartridges, visit our website at www.

mitsuparts.com or call (800) 553-7278.

• For questions:

Call Consumer Relations at 800-332-2119.

E-mail: [email protected]

Website: www.mitsubishi-tv.com

Important

All lamps replaced under warranty must be returned to Mitsubishi where they will be inspected for defect verification.

74

Appendices

Appendix E: Troubleshooting, continued

Reset Name

A/V Reset

(for all inputs)

Channel

Memorization

Lock Menu

Pass Code

Control-Panel

Lock Release

Auto Input

Sensing for

HDMI

System Reset

When to Use

To reset audio and video adjustments for all inputs to the original factory settings.

To erase and re-memorize channels on the ANT input.

To change your menu pass code

Lock

How to Use

While viewing the TV, press the control-panel buttons ACTIVITY and

VOLUME DOWN at the same time for at least two seconds.

1.

2.

3.

4.

5.

6.

While viewing the TV, press

MENU to display the main menu.

Navigate to the Initial> Channel menu.

Press ENTER.

Highlight the reception mode, e.g. Ant Air.

Highlight

Press

Scan.

ENTER to start channel memorization.

See the cutout page from Appendix B, page 65.

Resulting Action

All Audio and Video settings are returned to the original factory settings, including Listen To,

Language, audio Balance,

Closed Captions, and Format.

All previously memorized channels for the antenna input are erased and a new set of memorized channels is created. To add or delete individual channels, see

Initial > Channel > Edit menu instructions on page 39.

Allows establishment of a new code.

To re-enable the control-panel buttons after activation of the

Control-Panel Lock

If the New Device

Found screen does not appear when you connect an HDMI device.

If the TV does not turn on or off, does not respond to the remote control or controlpanel buttons, or has audio but no video.

Press and hold the ACTIVITY button on the control panel for ten seconds.

If the TV is powered off, you can now press the POWER button to turn it on.

Allows the control panel to be unlocked if the remote control is misplaced.

The New Device Found screen will display.

1.

2.

3.

Disconnect the HDMI device.

Delete the HDMI input in the

Inputs > Name menu (see page

40).

Power on and connect the new device.

Press and hold the POWER button on the control panel for ten seconds.

The TV will turn off. Power on the

TV and the green LED will flash quickly for about one minute. The changes you made most recently, before using SYSTEM RESET, may be lost.

TV Reset

IMPORTANT:

Use this reset only if other troubleshooting has been unsuccessful.

To reset all consumeraccessible settings and all memories to the original factory defaults.

Use TV Reset if the TV can respond to controls but TV behavior is abnormal.

1.

2.

3.

CAUTION: All ownerperformed setups and adjustments will be erased.

While viewing the TV, press

MENU to display the TV main menu.

With the main menu displayed, press number keys 1 2 3 to display the Reset menu.

READ THE ON-SCREEN

WARNING AND INSTRUC-

TIONS.

If you do not wish to use this reset, press BACK or MENU to back out.

If you do wish to use the reset, press ENTER to erase all memories and settings.

The TV will start the initialization process and then turn off.

Power on the TV and the front green LED will start flashing. All memory and settings outlined in this Owner’s Guide will need to be set again.

Appendices

75

Appendix E: Troubleshooting, continued

General TV Operation

2.

3.

Symptom

1.

A fan is running even while the TV is powered off.

The fan gets louder after the TV is shut off.

The TV remote control does not work.

Remarks

The room is too warm. When the TV is off, internal components continue to draw power and must be cooled by the fan.

Normal operation. The fan speeds up to cool the lamp quickly after the TV has been shut off.

Check that the batteries are fresh and installed correctly.

Check that the control mode on the remote is set to TV.

Be no more than 20 feet from the TV when using the remote control.

Program the remote control to operate the TV or other device.

Reset the remote control.

Replace the batteries.

4.

When I try to use the remote control, the

POWER key blinks five times.

5.

TV does not respond to the remote control or to control-panel buttons and TV will not power on or off.

6.

When a device is selected from the Activity menu, the screen is blue or black (no signal source).

Unplug the AC power cord for 10 seconds.

Press and hold the POWER button on the control panel to perform system reset.

• Make sure the selected device is turned on.

• Begin play of the device.

7.

You have forgotten your Lock menu pass code.

See “Bypassing the Parental Lock”, Appendix B.

8.

Rating restrictions are not working.

Open the Lock > Parental Lock menu and:

• Verify that the ratings locks are active.

• Check the Lock Time/Unlock Time to check if rating restrictions are disabled.

• Rating restrictions apply only to content on the ANT input.

9.

On-screen displays appear each time you change a function.

Normal TV operation.

10. A warning message appeared on screen stating, “TV will shut down in a few seconds.

Please check if the air flow is blocked.”

11. I have turned on CEC for my HDMI devices but control is erratic and I wish to disable it.

• Internal TV temperature has exceeded proper levels. Cool the room.

• The TV has overheated. Clear blocked air vents and ensure at least four inches of clearance on all sides of the TV.

• Clean the air filter on the lamp cartridge.

First turn off the TV’s HDMI control for the specific device.

Open the Inputs > HDMI Control menu, select the device, select Off.

Disable CEC on the device itself. See the device’s instructions.

If the problem persists, do the following:

1. Disconnect the device from the TV.

2. Open the Inputs > Name menu and select Delete for the

3. device.

Reconnect the device to the TV and Auto Input Sensing will recognize the device with CEC disabled.

76

Appendices

Appendix E: Troubleshooting, continued

TV Channels

2.

Symptom

1.

The TV takes several seconds to respond to channel changes.

You cannot access a channel.

3.

When ChannelView list is displayed, information appears incomplete

Remarks

It is normal for digital channels to take longer to tune in.

Press ENTER after entering a channel number to avoid delays.

Use a 4-digit number for an over-the-air digital channel.

Use a 6-digit number for digital cable channels if your cable service is able to recognize 6-digit channel numbers.

Use number keys instead of CHANNEL Up/Down.

Be sure the channel you want to view is in memory.

Check that the TV is switched to the correct device or antenna for that channel by pressing the ACTIVITY key.

Make sure the Lock > Parent menu lock is set to Off.

If you cannot tune to a virtual digital channel even though the

TV has already memorized digital channels, tune to the physical channel number used by the broadcaster. The virtual channel will then be automatically added to memory.

You may be trying to tune to an analog channel that is no longer broadcasting.

Press INFO to update the display for the highlighted channel.

Program information is displayed only for the currently tuned channel.

Available information is sent from the broadcaster or cable provider. No other data is available.

Make sure the TV clock is set correctly.

TV Power On/Off

Symptom

1.

TV takes an excessively long time to power on.

2.

You cannot program the TV to turn on automatically (Timer function)

3.

TV turned itself off and the light on the front panel started to blink.

4.

TV will not power off.

Remarks

When powered on, the TV needs time to boot up, just as a computer does. Also, the TV’s lamp requires a few moments to heat up to full brightness.

The TV may be locked.

The clock may not be set.

Momentary power fluctuation caused the TV to turn off to prevent damage. Wait for the green light to stop flashing and turn the TV on again.

If the TV does not stay on, press the POWER button on the control panel for at least eight seconds to perform System

Reset. If this happens frequently, obtain an AC line power conditioner/surge protector.

An unusual digital signal may have been received, triggering a protection circuit. Wait for the light to stop flashing and turn TV on.

Press the POWER button on the control panel for ten seconds to perform System Reset.

Appendices

77

Appendix E: Troubleshooting, continued

Picture

1.

Picture does not look like a high-definition

2.

3.

4.

Symptom picture.

TV has sound but no picture.

Picture has become dimmer.

There is a large black or gray rectangle on the screen.

Remarks

Not all signals are high-definition signals. To receive high-definition programming from your cable or satellite provider, you must subscribe to the provider’s high-definition service. Some overthe-air broadcasts are in high-definition and can be received with a high-quality antenna suited to your location.

Check that all video inputs are plugged in firmly.

Press and hold the POWER button on the control panel for ten seconds to perform System Reset.

• The lamp is nearing the end of its life. Order a new lamp.

• Adjust picture brightness and contrast to maximum levels.

• Change Lamp Energy from Standard to Bright.

The TV’s analog closed captioning has been set to “text” mode in the Captions menu. Turn off because there is no text information being broadcast.

Check your VCR’s owner’s guide for further troubleshooting. 5.

You cannot view a picture when playing a

VHS tape.

6.

VCR or DVD player’s on-screen menus jitter up and down.

7.

When viewing a stopped VCR, white lines are rolling on the screen.

Stop playback. Possible cause: Many VCRs and DVD players provide on-screen menus at only half-resolution that may appear to jitter up and down.

• Turn off video mute for the VCR.

• Begin playing the tape.

• Change the VCR input from Line 1 to the VCR antenna input.

The PerfectColor color balance has been incorrectly set. Reset the PerfectColor balance.

8.

A color program appears as a black and white image, or the colors are dim, or the screen is black.

9.

Picture from an HDMI input is noisy (poor quality).

10. The image from a computer appears distorted when viewed on the TV.

Upgrade a Category 1 (unmarked) HDMI cable to a Category 2 high-speed HDMI cable.

Normal TV operation. The TV does not correct distortion in the picture from a computer because the correction process may cut off the edges of the image.

The aspect ratio may be wrong for the image. Press MORE and then 0 (FORMAT) to change.

Sound

Symptom

1.

There is no sound even when the volume is turned up.

Remarks

• Check if the MUTE key is on.

• The TV’s “Listen to:” setting may be set to SAP (analog program from the ANT input) but no SAP is being broadcast.

• Check that the Speakers option is set to TV to hear sound from the TV speakers. Possibly sound is being sent to one of the audio outputs for an A/V receiver or headphones.

• If using an A/V receiver, check that the Speakers option is set to AV

Receiver to hear sound from the A/V receiver speakers.

• Press and hold the POWER button on the control panel for 10 seconds to perform System Reset.

78

Appendices

Appendix E: Troubleshooting, continued

Sound

4.

Symptom

2.

The sound does not match the screen picture.

3.

The sound from my A/V receiver does not match the screen picture (I should hear the correct audio from my A/V receiver).

Cannot select an audio-only device; it does not appear in the Activity menu.

5.

.

Sound is coming from the TV speakers instead of the A/V receiver.

Remarks

The TV’s “Listen to:” setting may be set to SAP (analog program from the ANT input).

Check that DIGITAL AUDIO OUTPUT and/or AVR AUDIO

OUTPUT on TV’s main panel is connected to the A/V receiver.

Without this connection, devices connected only to the TV (and not the A/V receiver) can be heard only from the TV speakers.

Note that this includes the ANT input, a device (such as a camcorder) connected to the convenience panel, and any other device sending audio to the TV only.

If using a NetCommand-controlled A/V receiver, NetCommand may be selecting the wrong A/V receiver audio input. Check the

A/V receiver’s NetCommand setup in the Inputs > AVR menu.

Plug an unused video plug into the Y/VIDEO jack to activate Auto

Input Sensing and make the audio device selectable in the Activity menu.

Disconnect headphones. Connect the TV’s AUDIO OUT to the A/V receiver and select AV Receiver from the New Device Found screen.

NetCommand IR Control (NetCommand-equipped models only)

Symptom

1.

Cannot see the menu from the A/V Receiver.

Remarks

• A/V Receiver Set Up for Audio-Only Switching

The A/V Receiver is not connected to any video input of the

TV. To check the A/V Receiver menu, temporarily plug into an unused input of the TV, such as Input 3. Exit the New

Device Found screen and select Input 3 from the Activity menu. Press MENU on the A/V receiver’s remote control.

A/V Receiver Set Up for Audio and Video Switching over

HDMI

Use the MENU key on the A/V receiver’s remote control.

A/V Receiver with HDMI Control

Switch the remote control to AUDIO mode. Press the

MORE key and then 1 (Menu).

2.

NetCommand unable to learn specific device keys.

A/V Device does not use IR format for remote control signal. ITT and RF formats cannot be learned.

Room lighting may affect the signal. Have the remotes very close (6 inches or less) to the TV during Learning.

If learning a Mitsubishi remote control, make sure mode is not set to TV.

Some, but not all, device key functions can be learned by

NetCommand. For example, POWER and PLAY may be learned, but other functions may not.

The signal from the remote control may not be strong enough. Insert fresh batteries and try Learning again.

Appendices

79

Appendix E: Troubleshooting, continued

NetCommand IR Control (NetCommand-equipped models only)

Symptom Remarks

3.

The A/V receiver is the selected audio source but there is no sound.

• A/V Receiver Set Up for Audio-Only Switching

Check to see if the A/V Receiver power is turned on.

With A/V receiver power turned on, redisplay the Activity menu and press ENTER to allow NetCommand to

correctly select the A/V Receiver input.

Incorrect setup in the Inputs > AVR menu. Check the device connection assigned in the AVR menu.

• A/V Receiver Set Up for Audio and Video Switching over HDMI

Check to see if the A/V Receiver power is turned on.

If the device is connected only to the TV (e.g., on ANT or a front panel input), verify that the TV’s AUDIO

-

OUTPUT is connected to the A/V receiver.

The A/V receiver is not switching properly because you have not learned the IR codes for the A/V receiver inputs to which your devices are connected.

NetCommand A/V receiver setup for the DVD player or digital surround sound device or other device is not switching properly. See “Case 2: Automatic A/V Receiver Switching to a Surround Sound Device,” page 54, and perform A/V receiver setup for a digital surround sound device.

4.

There is no sound from the A/V receiver for my DVD player or other surround sound device even though I learned the IR code for the A/V receiver’s DVD input or other input.

(A/V Receiver Set Up for Audio-Only Switching)

5.

There is no sound or picture from the A/V receiver for my DVD player or other device connected to the A/V receiver; the A/V receiver should be sending video to the TV over an HDMI cable.

(A/V Receiver Set Up for Audio and Video

Switching over HDMI)

6.

I’ve selected my DVD player or other surround sound device in combination with the

TV speakers but hear no sound from the TV speakers.

The NetCommand A/V receiver setup is not switching audio and video inputs properly because you did not “learn” the A/V receiver’s IR codes for the device inputs. See “Case 3: Automatic Audio and Video Switching via HDMI,” page 55.

7.

I “learned” the RECORD key for my VCR/DVR but when I pressed the RECORD key, the

VCR/DVR did not record anything.

• A/V Receiver Set Up for Audio-Only Switching

If you have only an audio connection from the device to the

A/V receiver, a physical audio connection from the device to the TV is also required.

Connect the left and right audio output from the device to the appropriate TV audio input. Now you can hear

audio from the device through either the TV speakers or the A/V receiver.

To switch audio sources, press MORE 9 (Audio), press to show the Speakers option, then press to select AV Receiver or TV.

• A/V Receiver Set Up for Audio and Video Switching over HDMI

With your DVD player connected to the A/V receiver, only video is passed from the A/V receiver to the TV because of copy-protection restrictions on the HDMI signal

Check that the VCR or DVR is receiving a signal directly from your cable box or satellite receiver.

80

Trademark and License Information

Trademark and License Information

LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY

EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,

INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABIL-

ITY OR FITNESS FOR A PARTICULAR PURPOSE.

Digital Light Processing ® and DLP ® are registered trademarks of Texas Instruments.

Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.

ENERGY STAR ® and the ENERGY STAR mark are registered U.S. marks. ENERGY STAR is a registered mark owned by the U.S. government.

HDMI ™ the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI

Licensing LLC.

Imaging Science Foundation Certified Calibration Controls

The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas

G. Lane, all rights reserved.

x.v.Color and the x.v.Color logo are trademarks of Sony Corporation.

ChannelView™, DeepField™ Imager, Easy Connect™, NetCommand®, PerfectColor™, PerfecTint™, Plush 1080p®

5G, SharpEdge™, Smooth120Hz™ are trademarks of Mitsubishi Digital Electronics America, Inc.

Trademark and License Information

81

Mitsubishi TV Software

END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE

IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and

Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.

The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws and treaties. The Software is licensed, not sold.

1. LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software only with the Mitsubishi television model that included this owner’s guide and owned by you.

2. RIGHTS AND LIMITATIONS.

Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that

Software has been pre installed.

Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the

Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.

Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more than one TV.

No Rental. You may not rent, lease, lend, or sublicense the Software.

Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA.

3. VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License, may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with any violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This license is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply with any provision of this License.

4. COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs, animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are owned by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the Software is recorded, but MDEA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MDEA.

5. EXPORT RESTRICTIONS. MDEA is licensing the Software for use within the United States. You agree that you will not export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq, Libya,

North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development, or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in

U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA nor any other U.S. federal agency has suspended, revoked, or denied your export privileges.

6. DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY

APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE

AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH

RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA. IN

NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY

DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME

JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY

NOT APPLY TO YOU.

7. LIMITATION OF LIABILITY. MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD

PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR

OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES

MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT NEITHER MDEA’S

BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE

ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. MDEA’s liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the money paid by you for the TV (based on fair market value of the TV) that caused the damages.

8. GENERAL. This License Agreement will be governed by the laws of the State of California.

WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.

82

Trademark and License Information

GNU General Public License

Version 2, June 1991

Copyright (C) 1989, 1991 Free Software Foundation, Inc.

675 Mass Ave, Cambridge, MA 02139, USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the

Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.

The precise terms and conditions for copying, distribution and modification follow.

GNU GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this

General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.

Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.

c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License.

(Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works.

But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this

License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on

Trademark and License Information

83

a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/ donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission.

For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLI-

CABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS”

WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-

ABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.

SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO

MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS

OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE

WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

84

Warranty

Mitsubishi DLP Projection Television Limited Warranty

MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants as follows to the original purchaser of this television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects arising from improper workmanship and/or material:

a. Parts. The lenticular (i.e. front picture) screen is warranted against defects in materials and workmanship for a period of thirty (30) days from the date of the original purchase at retail. The lamp and all other parts (except any software incorporated into this television) are warranted for a period of one (1) year from the date of the original purchase at retail. We will repair or replace, at our option, any defective part without charge for the part. Parts used for replacement may be replaced with those of like kind and quality and may be new or remanufactured. Parts used for replacement are warranted for the remainder of the original warranty period.

b. Embedded Software. MDEA warrants that all software incorporated into this television set (the “Embedded

Software”) will perform in accordance with the functional description of Embedded Software in all material respects, but MDEA does not warrant that the Embedded Software is error-free. The limited warranty contained in this section shall continue for a period of one (1) year from the date of the original purchase at retail. If, after prompt notice within the warranty period, MDEA determines that the Embedded Software has failed to perform in accordance with such functional description in all material respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then MDEA shall modify or replace the nonconforming Embedded Software at no charge to you, which at MDEA’s sole discretion may be fulfilled by means of modification or replacement software contained on a replacement memory card for Customer installation. The foregoing shall be MDEA’s sole obligation to you under this limited warranty. All rights under this limited warranty on the Embedded Software also subject to your acceptance of and compliance with the terms of the Software License Agreement applicable to this television, and this limited warranty on the Embedded Software shall be null and void if the Embedded Software is modified or changed in any manner except as specifically authorized by MDEA.

c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option, the lenticular screen if it proves defective. For certain items that are designed to be replaced by the consumer, including (but not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other parts, we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for one (1) year from the original date of purchase at retail.

d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the applicable warranty time period.

e. This DLP Projection Television uses a single DLP chip to create the screen image. This technology creates the image using small dots, or picture elements (pixels). Your DLP Projection TV is manufactured to a high level of performance and quality, in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology, sometimes a pixel is continuously active, inactive or the incorrect color. Our standard is clear; MDEA warrants only that the percentage of properly functioning pixels will be not less than 99.99% of all pixels.

BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and correct customer control adjustment. If the problem persists please arrange for warranty service.

1. TO OBTAIN WARRANTY SERVICE: a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your

MITSUBISHI dealer, by writing at the address provided below, calling MDEA at the 800-332-2119, or by using the support feature of our website at www.Mitsubishi-tv.com.

b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center.

If not, you must either deliver your television to an authorized service location at your own expense, or pay for any travel and/or transportation costs the service center may charge to and from your home. Actual service labor will be provided without charge.

c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service.

Present your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE

Warranty

85

OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However, please return the Owner Registration Card so that we can contact you should a question of safety arise which could affect you.

d. To obtain a replacement lamp, order the lamp directly from the MDEA Parts Department at (800) 553-7278.

2. THIS LIMITED WARRANTY DOES NOT COVER: a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).

b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other than an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to carry out any maintenance as described in the Owner’s Guide including air vent cleaning or any product damaged by excessive physical or electrical stress); any products that have had a serial number or any part thereof altered, defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage caused by acts of God or other factors beyond the reasonable control of MDEA, such as power surge damage caused by electrical system or lightning. This limited warranty also excludes service calls where no defect in the product covered under this warranty is found, service calls related to unsatisfactory audio or visual reception or signal unless caused by a defect in the product that is covered under this limited warranty, all costs, expenses or any other damages arising from product installation, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for display or use, connection with any external audio receiver, antenna, cable or satellite systems, or service of products purchased or serviced outside the U.S.A. Please consult the operating instructions contained in the Owner’s Guide furnished with the product for information regarding user controls.

3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION,

MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY

LIMITED TO A TERM OF ONE YEAR.

4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY

INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY,

BREACH OF CONTRACT, OR OTHERWISE.

5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental, special, or consequential damages, so the above limitations or exclusions may not apply to you.

6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

7. In the event of any dispute under this limited warranty, jurisdiction and venue for resolving that dispute will be in the state where the television was purchased and the laws of such state will govern.

MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.

9351 Jeronimo Road

Irvine, CA 92618-1904

86

Index

Index

A

Accent Lighting 33

Activity Menu 21

Automatic Generation 41

Change Input Name 40

Customizing 40

NetCommand-Controlled Switching of A/V Receiver Inputs 48

Removing a Disconnected HDMI

Device 40

Anamorphic Picture Format 24

Antenna Input (ANT) 15, 16

Signal Strength for Digital Channels 23

Audio Lock (A/V receiver control) 60

Audio Output Jacks 15, 16

Auto Input Sensing 11

Auto-Off (Sleep Timer) 21

Auto-On (Timer) 38

A/V Receiver and Speakers Option 36 and TV’s Remote Control 59

Audio Lock 60

Connecting 16, 20

Controlling Sound Volume 22

Disconnecting Analog 22

NetCommand IR Control 51, 52

Controlling a Device Connected to the A/V Receiver 31, 55

Video and Audio Switching via

HDMI 55

B

Batteries 7

Blue Glow 33

Bright (Lamp Mode) 39

Brightness (picture adjustment) 35

C

Cable Box and TV’s Remote Control 59

Connecting 17, 18, 19

Captions Menu 37

CEC (Consumer Electronics Control)

31, 66

A/V Receiver 22, 67, 77

Troubleshooting 74

Channels antennaweb.org 39

Physical/Virtual Channel Numbers 39

Scan (memorize) 10, 39

Troubleshooting 75

ChannelView™ Channel Listings 22

Cleaning 71

Clock, Set Date and Time 38

Closed Captions 37

Color Adjustments 34

Reset Color 34, 72

Computer and Display Formats 27

Connecting 26

Contrast 35

Control Panel 9

Control Panel Lock 9, 44

D

Date. See Clock

Default Settings, Returning to 72

DIGITAL AUDIO OUT 16

Dolby Digital 16, 54

DVD Player and TV’s Remote Control 59

Connecting 17, 18

DVI Device, Connecting 18

F

Fan Noise 4

Film Mode 33

Filter, Air (on lamp cartridge) 70

Font (digital closed captions) 37

FORMAT (aspect ratio, MORE menu)

24

Freeze Picture (PAUSE key) 8

Front Panel

Blue Glow Accent Lighting 33

Controls 9

G

Game

3D Video 25

Game Picture Mode 35

HDMI Cables for Games 16

GUIDE Key

ChannelView 22

HDMI Control 68

NetCommand Control 48, 50

H

HD (High-Definition) Signal) 24

HDMI

Changing Out an HDMI Device and Auto Input Sensing 11

Connecting an HDMI Device 17

A/V Receiver with HDMI 20

HDMI Cable Categories 16

HDMI Control of CEC Devices 66

HDMI Jack 16

Removing an HDMI Device from the Activity Menu 40

Headphones

Jack 16

Speakers Option 36

I

INFO Key

ChannelView 22

USB Menu 28

IR Emitter Placement 46

IR NetCommand Output (jack) 16

L

Lamp Cartridge Replacement 69

Lamp Mode 39

Language

Changing the Menu Language

38 in Digital Programs 36

SAP (Second Audio Program) 36

Learn 40. See also NetCommand IR

Control

Letter Box Image Display 24

Level Sound 36

Listen To 36

Listings 22

Lock TV

Bypassing the Lock 57

Lock by Ratings 43

Lock by Time 44

Lock Control Panel 44

Preset V-Chip Blocking 42

M

Memorizing Channels 10, 39

Add Single Channel to Memory

39

MP3 Player (audio-only connection)

15

Mute

Closed Captions 37

MUTE Key 8

Video Mute 33

N

Name (Inputs > Name menu) 40

NetCommand IR Control

About 45

A/V Receiver Control 52

Initial Setup for Most Devices 47

Operating 48

Troubleshooting 77

P

Parental Menu 43

Pass Code

Resetting 57

Setting 42

PAUSE Key 8

PerfectColor 34

PerfectTint 34

Photo Viewing 29

Picture

Picture+ Adjustments 34

Picture Menu Adjustments 35

Picture Quality and Film Mode

33

Troubleshooting 76

Power On/Off 9, 12

Troubleshooting 75

R

Ratings (TV and Movie) 43

Remote Control

Batteries 7

Keys and Functions 8

Programming Codes (reference chart) 61

Programming Instructions 60

Reset 71

Reset

A/V Memory Reset (for the current input) 72

A/V Reset (for all inputs) 73

HDMI Auto Input Sensing 11

Pass Code 57

PerfectColor/PerfecTint 72

Remote Control 71

Remote Control Audio Lock 60

System Reset 9

TV Reset Comparison Guide 72

RS-232C 16

S

Safety Instructions 5

SAP (second audio program) 36

Satellite Receiver and the Remote Control 59

Connecting 17, 18

Scan (memorize channels) 39

ScreenSaver 33

SD (Standard-Definition Signal) 24

Service and Support 72

Signal Definitions 24

Signal Strength Indicator 23

Sleep Timer 21

Sound

Controlling A/V Receiver Volume

(NetCommand) 52

Audio Lock 60

Level Sound 36

Sound Mode (audio effects) 36

Speakers Option 36

Standard-Definition Signal 24

Standard Lamp Mode 39

Stand Part Number 4

Status Display 23

Stereo System. See A/V Receiver

Surround Sound 53, 54

Simulated Surround Sound 36

TV Audio Outputs 16

System Reset 9, 73

T

Test Picture 33

3D GLASSES EMITTER Jack 16

3D Video 25, 34

Time. See Clock

Timer (auto-on) 38

Time Zone. See Clock

Troubleshooting 72

U

USB Menu 29

V

V-Chip Ratings

Definitions 43

In Status Display 23

VCR

Connecting 19

Troubleshooting 76

Video from a Digital Camera 30

Video Game. See Game

Video Mute 33

Viewing Device. See Activity Menu

X

x.v.Color 16, 17, 35

Index

87

Website:

www.mitsubishi-tv.com

E-mail:

[email protected]

For questions, call Consumer Relations at

800-332-2119

To order replacement or additional remote controls or lamp cartridges,

Visit our website www.mitsuparts.com

or call

800-553-7278

SYSTEM RESET

If the TV does not respond to the remote control, control-panel buttons, or will not power on/off, press and hold the POWER button on the control panel for ten seconds.

The TV will turn off. Power on the TV and the green LED will flash quickly for about one minute. The changes you made most recently, before using SYSTEM RESET, may be lost.

V41_V41+_V41C_IB_e_20090616

© 2009 Mitsubishi Digital Electronics America, Inc.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents