MULTIQUIP DCA-15SPX3 Specifications

MULTIQUIP DCA-15SPX3 Specifications
PARTS AND OPERATION MANUAL
© COPYRIGHT 2001, MULTIQUIP INC.
MQ POWER
Model DCA-15SPX3
WHISPERWATTTM
GENERATOR
Revision #2 (09/03/01)
MULTIQUIP INC.
PARTS DEPARTMENT:
18910 WILMINGTON AVE.
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
SERVICE DEPARTMENT:
310-537-3700
800-421-1244
800-835-2551
FAX: 310-537-3927
FAX: 310-638-8046
E-mail:[email protected] • www:multiquip.com
PAGE 2 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PAR
TS DEP
AR
TMENT
ARTS
DEPAR
ARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
VICE DEP
AR
TMENT
SER
ARTMENT
SERVICE
DEPAR
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEP
AR
TMENT
DEPAR
ARTMENT
800/835-2551, or 310/537-3700
FAX: 310/698-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 3
TABLE OF CONTENTS
Here's How To Get Help ............................................ 3
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Rules For Safe Operation ...................................... 6-9
Towing ..................................................................... 10
Trailer Safety Guidelines .................................... 11-16
Operation and Safety Decals ............................. 17-18
Specifications .......................................................... 19
General Information ................................................ 20
Major Components ................................................. 21
Dimensions ............................................................. 22
Control Panel Description .................................. 24-25
Output Terminal Information .............................. 26-28
Installation .......................................................... 30-31
Pre-Setup ........................................................... 32-35
Load Application ..................................................... 36
Generator Start-up Procedure ........................... 37-38
Generator Shutdown Procedure ............................. 39
Maintenance ...................................................... 40-41
Generator Wiring Diagram ...................................... 42
Engine Wiring Diagram ........................................... 43
Troubleshooting (Engine) ................................... 44-44
Troubleshooting (Generator/Engine) ...................... 46
Explanation of Codes in Remarks Section.............. 48
Suggested Spare Parts ........................................... 49
MQ Power DCA-15SPX3 Portable
Generator
Generator Assembly .......................................... 50-51
Control Box Assembly ........................................ 52-53
Output Terminal Assembly ................................. 54-55
Engine and Radiator Assembly .......................... 56-57
Battery Assembly ............................................... 58-59
Muffler Assembly ............................................... 60-61
Fuel Tank Assembly ........................................... 62-63
Enclosure Assembly ........................................... 64-67
Rubber Seals Assembly ..................................... 68-69
Operation and Safety Decal Locations .............. 70-71
Kubota V2203-D1-B Engine
Crankcase Assembly .........................................72-73
Oil Pan Assembly ...............................................74-75
Cylinder Head Assembly ....................................76-77
Gearcase Assembly ...........................................78-79
Main Bearing Case Assembly ............................80-81
Head Cover Assembly .......................................82-83
Inlet Manifold Assembly .....................................84-85
Exhaust Manifold Assembly ...............................86-87
Valve & Rocker Assembly ..................................88-89
Camshaft Assembly ...........................................90-91
Piston and Crankshaft Assembly .......................92-93
Flywheel Assembly ............................................94-95
Starter Assembly & Mounting ............................96-97
Starter (Components) Assembly ......................98-99
Nozzle Holder Assembly ............................... 100-101
Injection Pump 1 Assembly ........................... 102-103
Injection Pump 2 Assembly ........................... 104-105
Fuel Camshaft Assembly .............................. 106-107
Governor Assembly ...................................... 108-109
Speed Control Plate Assembly ..................... 110-111
Engine Stop Lever Assembly ........................ 112-113
Stop Solenoid Assembly ............................... 114-115
Alternator Assembly ...................................... 116-117
Alternator (Components) Assembly .............. 118-119
Fan Assembly................................................ 120-121
Water Flange & Thermostat Assembly ........ 122-123
Water Pump Assembly .................................. 124-125
Radiator Assembly ........................................ 126-127
Fuel Filter Assembly ..................................... 128-129
Terms and Conditions Of Sale — Parts ................ 130
PAGE 4 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
PARTS ORDERING PROCEDURES
■
■
■
■
■
■
■
Dealer account number
Dealer name and address
Shipping address (if different than billing address)
Return fax number
Applicable model number
Quantity, part number and description of each part
Specify preferred method of shipment:
•
•
•
•
UPS Ground
UPS Second Day or Third Day*
UPS Next Day*
Federal Express Priority One (please provide us with your Federal
Express account number)*
•
•
Airborne Express*
Truck or parcel post
*Normally shipped the same day the order is received, if prior to 2PM west coast time.
Earn Extra Discounts when
you order by FAX!
All parts orders which include complete part numbers
and are received by fax qualify for the following extra
discounts:
Number of
line items ordered
1-9 items
Additional Discount
3%
10+ items**
5%
Get special freight allowances
when you order 10 or more
line items via FAX!**
■ UPS Ground Service at no charge for freight
■ PS Third Day Service at one-half of actual freight cost
No other allowances on freight shipped by any other carrier.
**Common nuts, bolts and washers (all items under $1.00 list price)
do not count towards the 10+ line items.
*DISCOUNTS ARE SUBJECT TO CHANGE*
ount
c
s
i
D
Fax
Extra
c USA
i
t
s
e
m
for Do
Only
s
r
e
l
a
De
Now! Direct TOLL-FREE access
to our Parts Department!
Toll-free nationwide:
800-421-1244
Toll-free FAX:
800/6-PARTS-7 • 800-672-7877
Fax order discount and UPS special programs revised June 1, 1995
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 5
RULES FOR SAFE OPERATION
CAUTION:
Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only! This equipment is for
industrial use only.
The following safety guidelines should always be used when
operating the DCA-15SPX3 portable generator:
GENERAL SAFETY
■ NEVER touch the hot exhaust manifold,
muffler or cylinder. Allow these parts to cool
before servicing engine or generator.
■ High Temperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
■ DO NOT operate or service this equipment before
reading this entire manual.
■ This equipment should not be operated by
persons under 18 years of age.
■ NEVER operate this equipment without proper
protective clothing, shatterproof glasses, steeltoed boots and other protective devices required
by the job.
■ The engine of this generator requires an adequate free flow
of cooling air. Never operate the generator in any enclosed or
narrow area where free flow of the air is restricted. If the air
flow is restricted it will cause
serious damage to the
generator or engine and may
cause injury to people.
Remember the generator
engine gives off DEADLY
carbon monoxide gas.
■ NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
■ NEVER operate this equipment under the
influence or drugs or alcohol.
■ NEVER use accessories or attachments, which are not
recommended by MQ Power for this equipment. Damage to
the equipment and/or injury to user may result.
■ Manufacture does not assume responsibility for any accident
due to equipment modifications.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ Always check the machine for loosened threads or bolts before
starting.
CAUTION:
Always refuel in a well-ventilated area, away
from sparks and open flames.
Always use extreme caution when working
with flammable liquids. When refueling,
stop the engine and allow it to cool. DO
NOT smoke around or near the machine.
Fire or explosion could result from fuel
vapors, or if fuel is spilled on a hot engine.
■ NEVER operate the generator in an explosive atmosphere or
near combustible materials. An explosion or fire could result
causing severe bodily harm or even death.
■ Topping-off to filler port is dangerous, as it tends to spill fuel.
PAGE 6 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
RULES FOR SAFE OPERATION
CAUTION:
CAUTION:
DO NOT touch or open any of the below
mentioned components while the generator
is running. Always allow sufficient time for
the engine and generator to cool before
performing maintenance.
■ NEVER touch output terminals during operation. This is
extremely dangerous. Always stop the machine when contact
with the output terminals is required.
CAUTION:
■ Backfeed to a utility system can cause electrocution
and/or property damage. Do not connect to any
building's electrical system except through an approved
device or after building main switch is opened.
CAUTION:
Radiator
1. Radiator Cap - Removing the radiator cap while the
engine is hot will result in high pressurized, boiling water
to gush out of the radiator, therefore causing severe
scalding to any persons in the general area of the
generator.
2. Coolant Drain Plug - Removing the coolant drain plug
while the engine is hot will result in hot coolant to gush
out of the coolant drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
3. Engine Oil Drain Plug - Removing the engine oil drain
plug while the engine is hot will result in hot oil to gush
out of the oil drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
■ Never use damaged or worn cables when connecting power
tools or equipment to the generator. Make sure power
connecting cables are securely connected to the generator's
output terminals, insufficient tightening of the terminal
connections may cause damage to the generator and
electrical shock.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 7
RULES FOR SAFE OPERATION
■ NEVER Run engine without air filter. Severe engine damage
may occur.
CAUTION:
Battery
■ Never over fill the battery with water above
the upper limit.
■ Always service air cleaner frequently to prevent carburetor
malfunction.
■ Always disconnect the battery before performing service on
the generator.
■ Always be sure the operator is familiar with proper safety
precautions and operations techniques before using generator.
The battery has acids that can cause injury to the eyes and skin.
To avoid eye irritation, always wear safety glasses. Use well
insulated gloves when picking up the battery. Use the following
guidelines when handling the battery:
■ Always store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
■ DO NOT leave the generator running in the manual mode
unattended.
■ DO NOT allow unauthorized people to operate this
equipment.
■ Always read, understand, and follow procedures in Operator’s
Manual before attempting to operate equipment.
■ Always be sure the operator is familiar with proper safety
precautions and operations techniques before using generator.
■ Refer to the Kubota Engine Owner's Manual for engine
technical questions or information.
1. DO NOT drop the battery. There is the possibility of risk
the battery may explode.
2. DO NOT expose the battery to open flames, sparks,
cigarettes etc. The battery contains combustible gases
and liquids. If these gases and liquids come in contact
with a flame or spark, an explosion could occur.
3. Always keep the battery charged. If the battery is not
charged, a buildup of combustible gas will occur.
4. Always keep battery charging and booster cables in good
working condition. Repair or replace all worn cables.
5. Always recharge the battery in an open air environment,
to avoid risk of a dangerous concentration of combustible
gases.
6. In case the battery liquid (dilute sulfuric acid) comes in
contact with clothing or skin , rinse skin or clothing
immediately with plenty of water.
7. In case the battery liquid (dilute sulfuric acid) comes in
contact with your eyes, rinse eyes immediately with
plenty of water, then contact the nearest doctor or
hospital, and seek medical attention.
Loading and Unloading (Crane)
■ Before lifting, make sure the generator's lifting hook is secure
and that there is no apparent damage to the generator itself
(loose screws, nuts and bolts). If any part is loose or damaged,
please take corrective action before lifting.
■ Always drain fuel prior to lifting.
■ Always make sure crane or lifting device has been properly
secured to the hook of guard frame on generator.
■ NEVER lift the machine while the engine is running.
■ Use adequate lifting cable (wire or rope) of sufficient strength.
■ When lifting the generator, always use the balanced centerpoint suspension hook and lift straight upwards.
■ NEVER allow any person or animal to stand underneath the
machine while lifting.
■ When loading the generator on a truck, be sure to use the
front and back frame bars as a means to secure the generator
during transport.
PAGE 8 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
RULES FOR SAFE OPERATION
Transporting
■ Always shutdown engine before transporting.
■ Tighten fuel tank cap securely.
Maintenance Safety
■ NEVER lubricate components or attempt service on a running
machine.
■ Drain fuel when transporting generator over long distances
or bad roads.
■ Always allow the machine a proper amount of time to cool
before servicing.
■ Always tie-down the generator during transportation by
securing the generator.
■ Keep the machinery in proper running condition.
■ If generator is mounted on a trailer, make sure trailer complies
with all local and state safety transportation laws. See page
10 for basic towing procedures.
Emergencies
■ Always know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department.
■ Fix damage to the machine immediately and always replace
broken parts.
■ Dispose of hazardous waste properly. Examples of potentially
hazardous waste are used motor oil, fuel, and fuel filters.
■ DO NOT use plastic containers to dispose of hazardous
waste.
■ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 9
DCA-15SPX3 — TOWING
■ ALWAYS attach trailer's safety chain to bumper of towing
vehicle.
Towing Safety Precautions
CAUTION :
■
Check with your county or state
safety towing regulations department
before towing your generator.
To reduce the possibility of an accident while transporting
the generator on public roads, always make sure the trailer
that supports the generator and the towing vehicle are in
good operating condition and both units are mechanically
sound.
The following list of suggestions should be used when towing
your generator:
■ Make sure the hitch and coupling of the towing vehicle are
rated equal to, or greater than the trailer "gross vehicle weight
rating" (GVWR).
■ ALWAYS inspect the hitch and coupling for wear. NEVER
tow a trailer with defective hitches, couplings, chains etc.
■ Check the tire air pressure on both the towing vehicle and
the trailer. Also check the tire tread wear on both vehicles.
■ ALWAYS make sure the trailer is equipped with a "Safety
Chain".
■ ALWAYS make sure that the vehicle and trailer directional,
backup, brake, and trailer lights are connected and working
properly.
■ The maximum speed (unless otherwise posted) for highway
towing is 45 M.P.H.. Recommended off-road towing is not to
exceed 10 M.P.H. or less depending on type of terrain.
rolling,
■ Place chocked blocks underneath wheel to prevent rolling
while parked.
■ Place support blocks underneath the trailer's bumper to
prevent tipping, while parked.
■ Use the trailer's hand winch to adjust the height of the trailer,
then insert locking pin to lock wheel stand in place, while
parked.
■ Avoid sudden stops and starts. This can cause skidding, or
jackknifing. Smooth, gradual starts and stops will improve
gas milage.
■ Avoid sharp turns to prevent rolling.
■ Remove wheel stand when transporting.
■ DO NOT transport generator with fuel in tank.
Figure 1. DCA-15SPX3 and Towing Trailer
PAGE 10 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — TRAILER-SAFETY GUIDELINES
CAUTION :
4.
ALWAYS make sure the trailer is in good
operating condition. Check the tires for
proper inflation and wear. Also check the
wheel lug nuts for proper tightness.
Explanation of Chart:
This section is intended to provide the user with trailer service and maintenance information. The service and maintenance guidelines referenced in this section apply a wide range
of trailers. Remember periodic inspection of the trailer will
ensure safe towing of the equipment and will prevent damage to the equipment and personal injury.
It is the purpose of this section to cover the major maintenance components of the trailer. The following trailer components will be discussed in this section:
„
„
„
„
„
„
Brakes
Tires
Lug Nut Torquing
Suspension
Electrical
Brake Troubleshooting Tables
Use the following definitions with reading Table 1.
1. Fuel Cell - Provides an adequate amount of fuel for the
equipment in use. Fuel cells must be empty when transporting equipment.
2. Braking System - System employed in stopping the
trailer. Typical braking systems are electric, surge, hydraulic, hydraulic-surge and air.
3. GVWR- Gross Vehicle Weight Rating (GVWR), is the
maximum number of pounds the trailer can carry, including the fuel cell (empty).
Frame Length - This measurement is from the ball
hitch to the rear bumper (reflector).
5. Frame Width - This measurement is from fender to
fender.
6.
Jack Stand - Trailer support device with maximum
pound requirement from the tongue of the trailer.
7. Coupler - Type of hitch used on the trailer for towing.
8. Tire Size - Indicates the diameter of the tire in inches
(10,12,14, etc.), and the width in millimeters
(175,185,205, etc.). The tire diameter must match the
diameter of the tire rim.
9. Tire Ply - The tire ply (layers) number is rated in letters;
2-ply,4-ply,6-ply, etc.
10. Wheel Hub - The wheel hub is connected to the trailer’s
axle.
11. Tire Rim - Tires mounted on a tire rim. The tire rim must
match the size of the tire.
12. Lug Nuts - Used to secure the wheel to the wheel hub.
Always use a torque wrench to tighten down the lug
nuts. See Table 4 and Figure 3 or lug nut tightening and
sequence.
13. Axle - Indicates the maximum weight the axle can support in pounds, and the diameter of the axle expressed
in inches (see Table 3). Please not that some trailers
have a double axle. This will be shown as 2-6000 lbs.,
meaning two axles with a total weight capacity of 6000
pounds.
14. Suspension - Protects the trailer chassis from shocks
transmitted through the wheels. Types of suspension
used are leaf, Q-flex, and air ride.
15. Electrical - Electrical connectors (looms) are provided
with the trailer so the brake lights and turn signals can
be connected to the towing vehicle.
16. Application - Indicates which units can be employed
on a particular trailer.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 11
DCA-15SPX3 —TRAILER-SPECIFICATIONS
Table 1. Specifications
MODEL
APPLICATION
FU E L
C E LL
BRAKE
SYSTEM
GVWR
FRAME
LENGTH
FRAME
WIDTH
JACK
STAND
TRLR-10W
SDW225,
SGW250,TLW300
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-10
DCA10, TLG12,
DCA-15
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-10XF
DCA10, TLG-12,
DCA15, TLW-300
52 GAL
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-225W
WELDERS,
D A 7000S S
NO
NO
2200LB S
85"
42"
800LB .
FULL TILT WHEEL
TRLR-BLW400
BLW-400
NO
ELECTRIC
2700LB S
W/MAST 154"
W/O 124"
55"
(78" TALL)
800LB .
FULL TILT WHEEL
TRLR-50X
DCA-25
NO
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TRLR-50XF
DCA-25
41 GAL
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TRLR-70W
DCA-45, -60, 70
NO
SURGE
7000LB S
186"
77"
2000LB .
FLAT PAD
TRLR-70X
DCA-45, -60, 70
OPT
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TRLR-70XF
DCA-45, -60, 70
53 GAL
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TRLR-100XF
DCA-100, 125
150 GAL
HYDRAULIC SURGE
7000LB S
190"
76"
2000LB .
FLAT PAD
TRLR-85/125
DCA-85, 100,
125
145 GAL
HYDRAULIC
10000LB S
186"
77"
2000LB .
FLAT PAD
TRLR-150XF
DCA-150, 180
200 GAL
HYDRAULIC SURGE
11160LBS
204"
84"
5000 LB .
FLAT PAD
TRLR-220XF
DCA-220
250 GAL
HYDRAULIC SURGE
14000LB S
222"
83"
5000 LB .
FLAT PAD
TRLR-300XF
DCA-300
250 GAL
HYDRAULIC SURGE
18000LB S
238"
83"
5000 LB .
FLAT PAD
TRLR-400XF
DCA-400
350 GAL
ELECTRIC
18000LB S
238"
83"
5000 LB .
FLAT PAD
TRLR-600XF
DCA-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
TRLR-800SX
DCA-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
PAGE 12 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 —TRAILER-SPECIFICATIONS
Table 1. Specifications (Con't)
MODEL
COUPLER
TIRES
WHEELS
AXLE
HUBS SUSPENSION
ELECTRICAL
TRLR-10W
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.50"
2200# 2X 2
5 LUG
3 LE A F
4 WIRE LOOM W/
4 POLE FLAT
TRLR-10
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-10XF
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-225W
2" B A LL C LA S S
2 ADJUSTABLE
175-13B
13X4.5"
2200#2X 2
5 LUG
Q F LE X
4 POLE FLAT
TRLR-BLW
400
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13 X 4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-50X
2" B A LL C LA S S
B78-13LRC
13"X4.50"
3500lbs.
2-3/8"
5 LUG
4 LE A F
4 POLE RUBBER
FLAT
TRLR-50XF
2" B A LL C LA S S
B78-13LRC
13"X4.50"
3500lbs.
2-3/8"
5 LUG
4 LE A F
4 POLE RUBBER
FLAT
TRLR-70W
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs.
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-70X
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-70XF
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs.
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-100XF
ADJUSTABLE 2-5/6
OPT 3" EYE
205-15C
BIAS (4)
14"X5.5"
3500lbs
3"
5 LUG
5 LE A F
4 WIRE LOOM
TRLR-85/125
ADJUSTABLE 2-5/6
OPT 3" EYE
ST225/75R15D
RADIAL (4)
14"x6"
(2)-6000lbs
6 LUG
7 LE A F
4 WIRE LOOM
TRLR-150XF
3" BALL EYE
750-16 E
BIAS (4)
16" X 7"
(2)-6000lbs
8 LUG
7 LE A F
4 WIRE LOOM
TRLR-220XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(4)
16" X 7"
(2)-7000lbs
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-300XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(6)
16" X 7"
(2)-6000lbs
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-400XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(6)
16" X 7"
(3)-7000lbs.
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-600XF
5TH WHEEL
ST215/75R17.5H
RADIAL (8)
16" X 7"
(3)-10000lbs
8 LUG
7 LE A F
6 WIRE LOOM
TRLR-800AR
5TH WHEEL
ST215/75R17.5H
RADIAL (8)
16" X 7"
(3)-10000lbs
8 LUG
AIR-RIDE
6 WIRE LOOM
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 13
DCA-15SPX3 —TRAILER SAFETY GUIDELINES
Tires/Wheels/Lug Nuts
Tires and wheels are a very important and critical
components of the trailer. When specifying or replacing the
trailer wheels it is important the wheels, tires, and axle are
properly matched.
CAUTION:
DO NOT attempt to repair or modify a
wheel. DO NOT install in inner tube to
correct a leak
through the rim.
If the rim is
cracked, the air
pressure in the inner tube may
cause pieces of the rim to explode
(break off) with great force and
cause serious eye or bodily injury.
Tire Wear/Inflation
Tire inflation pressure is the most important factor in tire life.
Pressure should be checked cold before operation DO NOT
bleed air from tires when they are hot. Check inflation
pressure weekly during use to insure the maximum tire life
and tread wear.
Table 2 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
Suspension
The leaf suspension springs and associated components
(Figure 2) should be visually inspected every 6,000 miles for
signs of excessive wear, elongation of bolt holes, and
loosening of fasteners. Replace all damaged parts
(suspension) immediately. Torqued suspension components
as detailed in Table 3.
CAUTION:
NOTE
Figure 2. Major Suspension Components
ALWAYS wear safety glasses when removing
or installing force fitted parts. Failure to comply
may result in serious injury.
PAGE 14 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — TRAILER SAFETY GUIDELINES
Table 3. Suspension Torque Requirements
Item
Torque (Ft.-Lbs.)
3/8" U-BOLT
MIN-30 MAX-35
7/16" U-BOLT
MIN-45 MAX-60
1/2" U-BOLT
MIN-45 MAX-60
SHACKLE BOLT
SNUG FIT ONLY. PARTS MUST ROTATE FREELY.
SPRING EYE BOLT
LOCKING NUTS OR COTTER PINS ARE PROVIDED TO
RETAIN NUT-BOLT ASSEMBLY.
MIN-30 MAX-50
SHOULDER TYPE
SHACKLE BOLT
Lug Nut Torque Requirements
It is extremely important to apply and maintain proper wheel
mounting torque on the trailer. Be sure to use only the
fasteners matched to the cone angle of the wheel. Proper
procedure for attachment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
2. Torque all lug nuts in sequence. See Figure 3. DO NOT
torque the wheel lug nuts all the way down. Tighten
each lug nut in 3 separate passes as defined by Table 4.
3. After first road use, retorque all lug nuts in sequence.
Check all wheel lug nuts periodically.
Table 4. Tire Torque Requirements
Wheel Size
First Pass
FT-LBS
Second Pass
FT-LBS
Third Pass
FT-LBS
12"
20-25
35-40
50-65
13"
20-25
35-40
50-65
14"
20-25
50-60
90-120
15"
20-25
50-60
90-120
16"
20-25
50-60
90-120
Figure 3. Wheel Lug Nuts Tightening Sequence
NOTE
NEVER use an pneumatic air gun to
tighten wheel lug nuts.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 15
DCA-15SPX3 —TRAILER WIRING DIAGRAM
NOTE:
LIGHTS ARE ORIENTED FROM THE DRIVER’S SEAT
PAGE 16 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — OPERATION AND SAFETY DECALS
Machine Safety Decals
The DCA-15SPX3 generator is equipped with a number of safety decals. These decals are provided for operator safety and
maintenance information. The illustration below and on the preceding pages show these decals as they appear on the machine.
Should any of these decals become unreadable, replacements can be obtained from your dealer.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 17
DCA-15SPX3 — OPERATION AND SAFETY DECALS
Machine Safety Decals
PAGE 18 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — SPECIFICATIONS
Table 5. Specifications
Generator Specifications
Model
DCA15SPX3
Type
Rotating-Field, Protection Type,Synchronous
Excitation
Brushless Type (With A.V.R)
Phase
Single Phase
Frequency
60 Hz
Wires
3-Wires (Neutral Grounded)
Max. Rated Output
16.5 kW
Continious Rated Output
15 kW
Single Phase Output Voltage
120/240 Volts
Frequency
60 Hz
Power Factor
100%
Speed
1800 rpm
Engine Specifications
Model
KUBOTA V2203
Type
Vertical, 4-Cycle
No. of Cylinders
4
Displacement
134.08 cu. in. (2.197 liters)
Bore X Stroke
3.43 in. X 3.64 in. (87 mm X 92.4 mm)
Cooling System
Water-Cooled
Starting System
Electric Start
Cooling Water Capacity
1.94 gal (7.4L)
Lube Oil Capacity
16.2 pints (7.6 L)
Battery
12V-70Ah
Fuel
Diesel Fuel Oil No. 2-D
1.37 gal/hr. (5.18 L/hr) At full load
Fuel Consumption
1.08 gal/hr. (4.08 L/hr.) At 3/4 load
0.83 gal/hr. (3.14L/hr.) At 1/2 load
0.62 gal/hr. (2.34 L/hr.) At 1/4 load
Sound At Full Load
62 dbA (distance = 23 feet)
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 19
DCA-15SPX3 — GENERAL INFORMATION
DCA-15SPX3 3 FAMILIARIZATION
Generator
ator
The MQ Power Model DCA-15SPX3 is a 15 kW gener
generator
that has been designed as a high quality portable (requires
a trailer for transport) power source for telecom sites, lighting
facilities, power tools, submersible pumps and other
industrial and construction machinery.
Control Panel
The control panel is provided with the following:
z One GFCI 120 volt receptacle, 20 amp (single-phase)
z 15 kW Output Terminal (UNV)
z Main Circuit Breaker 65 amps
z GFCI Circuit Breaker 20 amps
z AC Ammeter Indicator
z AC Voltmeter Indicator
z Output Voltage Adjustment Knob
z Engine Warning Indicator
z Engine Speed Control Lever
z Hour Meter
z Ground Terminal
Open Delta Excitation System
The DCA-15SPX3 generator is equipped with the state of
the art "Open-Delta" excitation system. The open delta
system consist of an electrically independent winding wound
among stationary windings of the AC output section.
There are four Leads: A, B, C and D. During light loads, the
power to the Automatic Voltage Regulator (AVR) is supplied
from the leads of B & C, when loads increase, the AVR
switches and accepts power from leads A & D. The output
of leads A & D increase proportionally with load. This has
the effect of adding the voltages of each phase to provide
better voltage response during heavy loads.
The connections of the AVR to the AC output windings are
for the sole purpose of sensing only. No power is required
from these windings.
The open-delta design provides virtually unlimited excitation
current due to its independent power supply offering
maximum motor starting capabilities. The excitation does
not have a "fixed ceiling " and responds according the
demands of the required load.
Engine
The DCA-15SPX3 is powered by a 4-cylinder KUBOTA Model
V2203 diesel engine. This engine is designed to meet every
performance requirement for the generator. Reference Table
5, page 19 for engine specifications.
In keeping with MQ Power's policy of constantly improving
its products, the specifications quoted herein are subject to
change without prior notice.
The basic controls and indicators for the DCA-15SPX3
generator are addressed on the following pages.
PAGE 20 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — MAJOR COMPONENTS
Figure 4. DCA-15SPX3 Generator Major Components
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 21
DCA-15SPX3 — DIMENSIONS
Figure 5. Dimensions
PAGE 22 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
NOTE PAGE
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 23
DCA-15SPX3 — CONTROL PANEL
Figure 6. Control Panel
PAGE 24 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — CONTROL PANEL
The definitions below describe the controls and functions of
the DCA-15SPX3 " Control Panel "(Figure 6).
1. Frequency Meter – Indicates the output frequency in
hertz (Hz). Normally 60 Hz ±1 Hz.
2. AC Ammeter – Indicates the amount of current the
load is drawing from the generator.
3. AC Voltmeter – Indicates the single phase output
voltage present at the U & V terminals.
4. Engine Warning Indicator- This engine warning
indicator will notify possible damage before it occurs:
A. Oil Pressure - the light will go on during initial
start, but will go out once the engine is warm. If the
oil pressure light comes on during operation, this may
indicate critical low oil level.
B. Charge Light - This light indicates the battery is
not charging.
C. Water Temperature Light - This light indicates the
coolant temperature is abnormally high.
D. Engine Protection - This will shut down the engine
if there is an abnormal event that may have occurred.
This prevents damage to the engine.
5. Hour Meter – Indicates the amount of hours the
generator has been in operational use.
6. GFCI Circuit Breaker – This single-pole, 20 amp
breaker is provided to protect the 120 VAC GFCI
receptacle from overload.
7. Starter Switch - This is to turn on and off the engine
with a key.
8. CS6369 Receptacle - This locking type receptacle
provides 240/120VAC single output voltage, for
equipment not exceeding 50 amps.
9. 240 VAC Receptacle – Provides 240 VAC single phase
output voltage, normally used for small power tools
that do not exceed 20 amps.
10. 120 VAC Receptacle – Provides 120 VAC single phase
output voltage, normally used for small power tools
that do not exceed 20 amps.
11. 120VAC Receptacle (GFCI)- Provides 120 VAC single
phase output voltage, normally used for small power
tools that do not exceed 20 amps.
12. Engine Speed Control Lever - This lever controls
the speed of the engine speed from idle to high for
maximum rpm.
13. Ground Terminal – If required this ground terminal is
to be used in conjunction with the GFCI receptacle
only.
14. AC Output Terminals – These three output terminals
(UNV), provide the single phase output voltage to the
load source. NEVER connect a load to these output
terminals when the main circuit breaker is "ON" and
the engine is running.
15. Voltage Adjust Control Knob – Used to adjust the
generator's single phase output voltage at the UNV
output terminals. This control knob is to be used in
conjunction with the AC voltmeter.
16. Main Circuit Breaker – This three-pole, 65 amp main
breaker is provided to protect the single phase UNV
voltage output from overload.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 25
DCA-15SPX3 — OUTPUT TERMINAL INFORMATION
DCA-15SPX3 FAMILIARIZATION
The Output Terminal panel is provided with the following:
z One GFCI 120 Volt Receptacle, 20 Amp (single-phase)
z 15 kW Output Terminal (UNV)
z Ground Terminal
z Main Circuit Breaker 65 amps
z GFCI Circuit Breaker 20 amps
120 Volt Receptacle
One GFCI Duplex Nema 5-20R (120V, 20 Amp) receptacle
is provided on the output terminal. This receptacle can be
used anytime the generator is in operation. The receptacle
is controlled by the circuit breaker located on the control
panel.
NEMA L5-30R Output Receptacle
The L5-30R receptacle supplies 30 amps at 120 volts. A 30
amp circuit breaker helps protect any load that it is feeding.
NEMA L6-30R Output Receptacle
The L6-30R supplies 30 amps at 240 volts. A 30 amp circuit
breaker helps protect any load that it is feeding.
NEMA CS-6369 Output Receptacle
The CS-6369 supplies 50 amps at 120/240 volts. A 50 amp
circuit breaker helps protect any load that it is feeding.
Connecting Load
Loads can be connected to the generator by the UNV Lugs or
the duplex receptacle (See figure 3). Make sure to read the
operation manual before attempting to connect a load to the
generator.
Pressing the reset button resets the receptacle after being
tripped. Pressing the "Test Button" (See Figure 7) in the
center of this receptacle will check the GFCI function. The Circuit Breakers
The DCA-15SPX3 has a main 65 amp circuit breaker and
receptacle should be tested at least once a month.
receptacle circuit breakers that are listed above. The main
purpose of the circuit breakers is to protect the load the generator
is powering.
Figure 7. GFCI Test Button
Maximum Output
The entire load connected to the UNV Lugs and both slots in
the duplex receptacle must not exceed 16.5 kW in standby or
15 kW in prime output.
Maximum Amps
The generator will provide a maximum total amps of 62.5.
Do not exceed the maximum allowed amperage!
PAGE 26 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — OUTPUT TERMINAL INFORMATION
Figure 8. Receptacle Location on
Generator
Figure 9. Receptacle Details
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 27
DCA-15SPX3 — OUTPUT TERMINAL INFORMATION
120V Hard Wire Hookup
240V Hard Wire Hookup
The output terminal panel, when suppling single phase 120
volts, will provide two circuits available at 62.5 amps with
any two wires plus the ground. (See Figure 10 below.)
The output terminal panel, when suppling single phase 240
volts, will provide one circuit available at 62.5 amps with
two wires plus the ground. (See Figure 11 below.)
Figure 10. Hard Wire Hookup
for 120 Volt
Figure 11. Hard Wire Hookup
for 240 Volt
NOTE
When using plural single phase
voltages, make sure to balance
the load on each of the single
phase legs.
PAGE 28 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
NOTE PAGE
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 29
DCA-15SPX3 — INSTALLATION
Outdoor Installation
Install the generator in a location where it will not be exposed
to rain or sunshine. Make sure the generator is on secure
level ground so that it cannot slide or shift around. Also
install the generator in a manner so that the exhaust will not
be discharged in the direction of nearby homes.
The installation site must be relatively free from moisture
and dust. All electrical equipment should be protected from
excessive moisture. Failure to do will result in deterioration
of the insulation and will result in short circuits and
grounding.
Foreign materials such as dust, sand, lint and abrasive
materials have a tendency to cause excessive wear, to the
engine and alternator parts.
CAUTION :
Pay close attention to ventilation when
operating the generator inside tunnels and
caves. The engine exhaust contains
noxious elements. Engine exhaust must
be routed to a ventilated area.
Indoor Installation
Exhaust gases from diesel engines are extremely poisonous.
Whenever an engine is installed indoors the exhaust fumes
must be vented to the outside. The engine should be installed
at least two feet from any outside wall. Using an exhaust
pipe which is too long or too small can cause excessive
back pressure which will cause the engine to overheat.
Eliminate the danger of deadly carbon monoxide gas.
Remember that exhaust fumes from any diesel engine are
very poisonous if discharged in a closed room, but harmless
if allowed to mix with the outside air. If the generator is
installed indoors, you must make provisions from venting
the engine exhaust to the outside of the building.
DO NOT cover ventilation areas on the enclosure. Covering
the ventilation grids will cause the engine to overheat.
CAUTION :
An electric shock is apt to happen when
vibrators are used. Pay close attention to
handling when operating vibrators and
always use rubber boots and gloves to
insulate the body from electrical shock.
Generator Grounding
To guard against electrical shock and possible damage to
the equipment, it is important to provide a good EARTH
ground.
Article 250 (Grounding) of the National Electrical Code (NEC)
provides guide lines for proper grounding and specifies the
cable ground shall be connected to the grounding system of
the building as close to the point of cable entry as practical.
NEC articles 250-64(b) and 250-66 set the following
grounding requirements:
1. Use one of the following wire types to connect the
generator to earth ground.
a. Copper - 10 AWG (5.3 mm2) or larger.
b. Aluminum - 8 AWG (8.4 mm2) or larger.
2. When grounding the generator (Figure 12) connect the
ground cable between the lock washer and the nut on
the generator and tighten the nut fully. Connect the other
end of the ground cable to earth ground.
3. NEC article 250-52(c) specifies that the earth ground
rod should be buried a minimum of 8 ft. into the ground.
NOTE
When connecting the generator to
any buildings electrical system
ALWAYS consult with a licensed
electrician.
PAGE 30 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — INSTALLATION
Figure 12.
Typical Generator Grounding Application
CAUTION :
Always check local codes for proper
grounding codes and laws.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 31
DCA-15SPX3 — PRE-SETUP
General Inspection Prior to Operation
Circuit Breaker
The DCA-15SPX3 generator has been thoroughly inspected
and accepted prior to shipment from the factory. However,
be sure to check for damaged parts or components, or loose
nuts and bolts, which could have occurred in transit.
Extension Cable
When electric power is to be provided to various tools or
loads at some distance from the generator, extension
cords are normally used. Cables should be sized to allow
for distance in length and amperage so that the voltage
drop between the generator and point of use (load) is
held to a minimum. Use Table 6 (cable selection guide)
as a guide for selecting proper cable size.
To protect the generator from an overload, a 3-pole, 65 amp,
main circuit breaker is provided to protect the UNV output
from overload. In addition a 2-pole, 20 amp GFCI circuit
breaker is provided to protect the GFCI receptacle from
overload. Make sure to switch both circuit breakers to the
"OFF" position prior to starting the engine.
NOTE
ALWAYS consult with a licensed
electrician for correct extension
cord wire size.
Table 6. Cable Selection (60 Hz, Single Phase Operation)
Load In Watts
Current in
Amperes At 120 At 240
Volts
Volts
Maximum Allowable Cable Length
#10 Wire
#12 Wire
#14 Wire
#16 Wire
2.5
300
600
1000 ft.
600 ft.
375 ft.
250 ft.
5
600
1200
500 ft.
300 ft.
200 ft.
125 ft.
7.5
900
1800
350 ft.
200 ft.
125 ft.
100 ft.
10
1200
2400
250 ft.
150 ft.
100 ft.
15
1800
3600
150 ft.
100 ft.
65 ft.
20
2400
4800
125 ft.
75 ft.
50 ft.
CAUTION: Equipment damage can result from low voltage.
PAGE 32 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — PRE-SETUP
Lubrication Oil
Fuel
Fill the engine crankcase with lubricating oil through the filler
hole, but do not overfill. Make sure the generator is level.
With the dipstick inserted all the way, but without being screw
into the filler hole, verify that the oil level is maintained
between the two notches (Figure 13) on the dipstick. See
Table 7 for proper selection of engine oil.
Fill the fuel tank with clean and fresh diesel fuel. DO NOT
fill the tank beyond capacity.
Pay attention to the fuel tank capacity when replenishing
fuel. Refer to the fuel tank capacity listed on page 19
Specification Table 5.
The fuel tank cap must be closed tightly after filling. Handle
fuel in a safety container. If the container does not have a
spout, use a funnel. Wipe up any spilled fuel immediately.
CAUTION :
Never fill the fuel tank while the engine is
running or in the dark. Gasoline spillage
on a hot engine can cause a fire or
explosion. If gasoline spillage occurs, wipe
up the spilled gasoline completely to
prevent fire hazards.
Coolant
Figure 13. Engine Oil Dipstick
When checking the engine oil, be sure to check if the oil is
clean and viscous. If the oil is not clean, drain the oil by
removing the oil drain plug, and refill with the specified amount
of oil as outlined in the Kubota Engine Owner's Manual.
Use only drinkable tap water. If hard water or water with
many impurities is used, the inside of the engine and radiator
may become coated with deposits and cooling efficiency
will be reduced. See maintenance section on page XX and
XX on instructions to flush out radiator.
An anticorrosion additive added to the water will help prevent
deposits and corrosion in the cooling system.
Table 7. Recommended Motor Oil
Temperature Range
Type Oil
104° F ~ 23° F
(40° C ~ -5°C)
SAE 30
23° F ~ 5° F
(-5° C ~ -15°C)
SAE 20 or SAE 10W-30
Below 5° C (-15°)
SAE 10W or SAE 10W-30
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 33
DCA-15SPX3 — PRE-SETUP
CAUTION :
When adding coolant or antifreeze to the
radiator, do not remove the radiator cap
until the unit has completely cooled.
Day-to-day addition of coolant is done from the reserve tank.
When adding coolant to the radiator, DO NOT remove the
radiator cap until the unit has completely cooled. See Table
8. for engine, radiator, and reserve tank coolant capacities.
Make sure the coolant level in the reserve tank is always
between the "H" and the "L" markings.
Table 8. Coolant Capacity
Engine and Radiator
1.11 Gal. (4.2L)
Reserve Tank
0.26 Gal. (1L)
Cleaning the Outer Radiator
The engine may overheat if the radiator fins become
overloaded with dust or debris. Periodically clean the radiator
fins with compressed air. Cleaning inside the radiator is
dangerous, so clean only with the engine turned off and the
battery disconnected.
Air Cleaner
Periodic cleaning/replacement is necessary. Inspect it in
accordance with the Kubota Engine Owner's Manual.
Fan Belt Tension
A slack fan belt may contribute to overheating, or to
insufficient charging of the battery. Inspect the fan belt for
damage and wear and adjust it in accordance with the Kubota
Engine Owner's Manual.
The fan belt tension is proper if the fan belt bends 10 to 15
mm (Figure 14) when depressed with the thumb as shown
below. Never place hands near the belts or fan while the
generator is running.
Operation in Freezing Weather
When operating in freezing weather, be certain the proper
amount
of antifreeze
9) hasisbeen
Day-to-day
addition (Table
of coolant
doneadded.
from the
Table 9. Anti-Freeze Operating Temperatures
Freezing Point
Figure 14. Fan Belt Tension
Boiling Point
Vol %
Anti-Freeze
°C
°F
°C
°F
40
-24
-12
106
222
50
-37
-34
108
226
NOTE
When the antifreeze is mixed with
w ater
atio m
ust
ater,, the antifreez
antifreezee mixing rratio
must
be less than 50%.
CAUTION :
Never place hands near the belts or fan
while the generator set is running.
Adjusting Fan Belt
If the fan belt does not have the 10 to 15mm defection
follow the procedure below to adjust:
Loosen the alternator adjusting plate and alternator mounding
bolt.
Pivot the alternator at the mounting bolt toward the engine
left or right until the belt reflects the proper tension.
Tighten the mounting bolt and the adjusting bolt.
PAGE 34 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — PRE-SETUP
Battery
This unit is of negative ground. DO NOT connect in reverse.
Always maintain battery fluid level between the specified
marks. Battery life will be shortened, if the fluid level is not
properly maintained. Add only distilled water when
replenishment is necessary. DO NOT over fill.
The battery is sufficiently charged if the specific gravity of
the battery fluid is 1.28 (at 68° F). If the specific gravity
should fall to 1.245 or lower, it indicates that the battery is
dead and needs to be recharged or replaced.
Check to see whether the battery cables are loose. Poor
contact may result in poor starting or malfunctions. Always
keep the terminals firmly tightened. Coating the terminals
with a thin film of grease will help to inhibit corrosion.
Battery Cable Installation
ALWAYS be sure the battery cables (Figure 15) are properly
connected to the battery terminals as shown below. The RED
cable is connected to the positive terminal of the battery,
and the BLACK cable is connected to the negative terminal
of the battery.
CAUTION :
If the battery cable is connected
incorrectly, damage to the generator will
occur. Pay close attention to the polarity
of the battery when connecting the
battery.
When connecting battery do the following:
1. DO NOT connect the battery cables to the battery
terminals when the key is in the ignition and is set in
'START' mode. ALWAYS remove the key from the
ignition and the ignition switch is in the OFF position
when connecting the battery.
2. Place a small amount of grease around both battery
terminals. This will ensure a good connection and will
help prevent corrosion around the battery terminals.
CAUTION :
Inadequate battery connections may
cause poor starting of the generator, and
create other malfunctions.
Wiring
Inspect the entire generator for bad or worn electrical wiring
or connections. If any wiring or connections are exposed
(insulation missing) replace wiring immediately.
Piping and Hose Connection
Inspect all piping, oil hose, and fuel hose connections for
wear and tightness. Tighten all hose clamps and check hoses
for leaks.
Figure 15. Battery Connections
If any hose (fuel or oil) lines are defective replace them
immediately.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 35
DCA-15SPX3 — LOAD APPLICATION
CAUTION:
Single Phase, Load
Always be sure to check the nameplate on the generator
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generator for operating the equipment.
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
NOTE
If wattage is not given on the
equipment's name plate, approximate
wattage may be determined by
multiplying nameplate voltage by the
nameplate amperage.
WATTS = VOLTAGE x AMPERAGE
The power factor of this generator is 1.0. See Table 10.
below when connecting loads.
Table 10. Power Factor By Load
Type Of Load
Power Factor
Single-phase induction motors
0.4 - 0.75
Electric heaters, incandescent
lamps
1.0
Fluorescent lamps, mercury lamps
0.4 - 0.9
Electronic devices, communication
equipment
1.0
Motors and motor-driven equipment draw
much greater current for starting than
during operation.
An inadequate size connecting cable which cannot carry
the required load can cause a voltage drop which can burn
out the appliance or tool and overheat the cable.
z When connecting a resistance load such as an
incandescent lamp or electric heater, a capacity of up
to the generating set’s rated output (kW) can be used.
z When connecting a fluorescent or mercury lamp, a
capacity of up to the generating set’s rated output (kW)
multiplied by 0.6 can be used.
z When connecting an electric drill or other power tools,
pay close attention to the required starting current
capacity.
When connecting ordinary power tools, a capacity of up to
the generating set’s rated output (kW) multiplied by 0.8 can
be used.
CAUTION:
Before connecting this generator to any
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch. Serious injury or death
may result without this transfer switch.
PAGE 36 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — GENERATOR START-UP PROCEDURE
WARNING:
The engine's exhaust contains harmful
W AY S ventilate the
emissions. A LLW
exhaust when operating inside tunnels,
excavations or buildings. Direct exhaust
away from nearby personnel.
2. Connect the load to the UNV terminals as shown in
Figure 17. These terminals can be found on the front of
the generator by lifting the UNV lug cover. It may be
necessary to remove the retaining lug that secures the
cover. Make sure to tighten terminal nuts securely to
prevent load wires from slipping out.
Before Starting
Engine
1. Check the lubricating oil level prior to starting the engine.
Make sure the generator is level. The oil level must be
maintained between two notches on the dipstick.
2. When there is not enough lubricating oil, fill the crankcase
with high grade motor oil. Use a high quality detergent
oil classified CC or higher (See Table 7 on page 29).
3. Check the coolant level in the radiator and subtank.
Replenish with antifreeze as necessary. Always maintain
the coolant level between the FULL and LOW markings
on the coolant container. Be sure that the radiator cap is
fastened securely.
4. Check the fuel level on the fuel gauge. If fuel is low, fill
the fuel tank with clean fresh unleaded automotive diesel
fuel. If fuel spillage occurs, clean immediately.
Figure 17. UNV Terminal Lugs (Load)
3. After attaching the load wires to the AC output terminals,
secure the UNV cover by inserting the retaining screw
(Figure 18) back into the cover.
Before Starting
Generator and Control Panel
CAUTION:
NEVER start the engine with the main
or GFCI circuit breakers in the ON
position.
1. Be sure to disconnect the electrical load and switch the
main and G.F
.C
.I. circuit breakers (Figure 16) to the
G.F.C
.C.I.
“OFF” position prior to starting the engine.
Figure 18. UNV Lug Cover
CIRCUIT BREAKER CIRCUIT BREAKER
GFCI RECEPTACLE
MAIN
OFF
OFF
Figure 16. Main and GFCI Circuit Breakers
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 37
DCA-15SPX3 — GENERATOR START-UP PROCEDURE
4. Connect the negative battery cable (BLACK) to the
negative post on the battery (Figure 19).
8. Pull the lever and turn to the right to increase the engine
speed. (Figure 23).
e X. Not In Auto
IVE
ST
PO
E
TIV
GA
NE
Figure 23. Engine Throttle Lever (HIGH)
Y
ER
TT
BA
Figure 19. Battery Connections
5. Close all engine enclosure doors (Figure 20).
9. The generator's voltage meter (Figure 24) displays the
120 VAC in VOLTS. If the voltage is not within the
specified frequency tolerance, use the voltage
adjustment control knob to the right of voltage meter to
bring the voltage within range.
VAC ADJUST
100
0
300
100
50
0
-
200
V
+
150
VOLTAGE
ADJUSTMENT
CONTROL
KNOB
Figure 20. Engine Enclosure Doors
6. Check the engine speed throttle lever is pushed in (low
speed) (Figure 21).
Figure 21. Engine Throttle Lever (LOW)
Figure 24. Voltage Meter/
Adjustment Control Knob
10. The ammeter (Figure 25) will indicate zero amps with
no load applied. When a load is applied, this meter will
indicate the amount of current that the load is drawing
from the generator.
7. Turn the key to preheat until the engine warms up (for 35 minutes). Then turn the key to the right until the engine
starts. Release the key to the 'run' mode (Figure 22).
20
40
0
60
75
A
Figure 25. Ammeter (No Load)
Figure 22. Ignition Switch (START)
PAGE 38 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — GENERATOR START-UP PROCEDURE
11. If there are no abnormal problems shown on the engine
indicator, turn both the MAIN and GFCI circuit breakers
to their ON position (Figure 26).
CIRCUIT BREAKER
MAIN
CIRCUIT BREAKER
GFI RECEPTACLE
ON
Engine Shutdown
To shutdown the generator use the following procedure:
1. Place both the MAIN and GFCI circuit breakers to the
"OFF position"
2. Turn the engine throttle lever to the left and push in to
decrease the engine speed.
3. Let the engine run 3-5 minutes with no load applied.
4. Turn the key to the left to stop the engine (Figure 28).
ON
Figure 26. Main and GFCI Circuit Breakers
12. Observe the generator's ammeter (Figure 27) and verify
that it reads the anticipated amount of current with
respect to the load. Remember the ammeter will only
display a current reading if the load is in use.
20
40
0
Figure 28. Ignition Switch (STOP)
5. Remove the load from the UNV terminal strip (Figure 14).
60
75
A
Figure 27. Ammeter (Load)
13. The generator will run until manually stopped or an
abnormal condition occurs.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 39
DCA-15SPX3 — MAINTENANCE
General Inspection
Check Oil Level
Prior to each use, the generator should be cleaned and
inspected for deficiencies. Check for loose, missing or
damaged nuts, bolts or other fasteners. Also check for fuel,
oil, and coolant leaks.
Engine Side (Refer to the Engine Instruction Manual)
Check the crankcase oil level prior to each use, or when
the fuel tank is filled. Insufficient oil may cause severe
damage to the engine. Make sure the generator is level.
The oil level must be between the two notches on the dipstick
as shown in Figure 8, page 29.
Replacing Oil Filter
Air Cleaner
Every 50 hours: Remove air cleaner element and clean heavy
duty paper element with kerosene, or foam element with
liquid detergent and hot water. Wrap foam element in a cloth
and squeeze dry. For heavy duty paper element, wipe
excess kerosene with towel.
Detach the oil filter cartridge with a filter wrench.
Fuel Addition
After the oil cartridge has been replaced, the engine oil
will drop slightly. Run the engine for a while and check
for leaks before adding more oil if needed. Clean
excessive oil from engine.
Add diesel fuel (the grade may vary according to season
and locations). Always pour through the mesh filter.
Removing Water from the Fuel Tank
After prolonged use, water and other impurities accumulate
in the bottom of the tank. Occasionally remove the drain
cock and drain the contents. During cold weather, the more
empty volume inside the tank, the easier it is for water to
condense. This can be reduced by keeping the tank full as
much as possible.
Apply a film of oil to the gasket for the cartridge.
Screw in the cartridge by hand. When the gasket is in
contact with the seal surface, tighten the cartridge one
or two more times by hand.
Replacing Fuel Filter
Replace the fuel filter cartridge with new one every 400
hours or so.
Apply fuel oil thinly over the gasket and hand-tighten
the cartridge into position.
Vent any air.
Flushing Out Radiator and Replacing Coolant
Air Removal
If air enters the fuel injection system of a diesel engine,
starting becomes impossible. After running out of fuel, or
after disassembling the fuel system, bleed the system
according to the following procedure.
To restart after running out of fuel, turn the switch to the
“ON” position for 15-30 seconds. Try again, if needed. This
unit is equipped with an automatic air bleeding system.
Service Daily
If the engine is operating in very dusty or dry grass
conditions, a clogged air cleaner will result. This can lead to
a loss of power, excessive carbon buildup in the combustion
chamber in high fuel consumption.
Cleaning the Fuel Strainer
Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in gasoline.
Securely fasten the fuel strainer cap so that fuel will not
leak. Check the fuel strainer every 200 hours of operation or
once a month.
Open both cocks located at the crankcase side and at
the lower part of the radiator and drain coolant. Open
the radiator cap while draining. Remove the overflow
tank and drain.
Check hoses for softening and kinks. Check clamps
for signs of leakage.
Flush the radiator by running clean tap water through
radiator until signs of rust and dirt are removed. DO
NOT clean radiator core with any objects, such as a
screwdriver.
Tighten both cocks and replace the overflow tank.
Replace with coolant (see page 30, Table 5 for mixture).
Close radiator cap tightly.
CAUTION :
Allow engine to cool when flushing out
radiator. Flushing the radiator while hot
will damage radiator.
PAGE 40 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — MAINTENANCE
Generator Storage
For storage of the generator for over 30 days, the following
is required:
z Fill the fuel tank completely.
z Completely drain the oil from the crankcase and refill
with fresh oil.
z Clean all external parts of the generator with a cloth.
z Cover the generating set and store in a clean, dry place.
INSPECTION / MAINTENANCE
ENGINE
GENERATOR
10 Hrs
DAILY
Check Engine Fluid Levels
X
Check Air Cleaner
X
Check Battery Acid Level
X
Check Fan Belt Condition
X
Check for Leaks
X
Check for Loosening of Parts
X
250 Hrs
Replace Engine Oil and Filter *1
X
Clean Air Filter
X
Drain Bottom of Fuel Tank
X
Clean Unit, Inside and Outside
X
500 Hrs
Change Fuel Filter *2
X
Clean Radiator and Check Coolant Protection
Level
X
1000 Hrs
Replace Air Filter Element
X
Change Corrosion Resistor
X
Check all Hoses and Clamps
X
Clean Inside of Fuel Tank
X
Measure Insulation Resistance Over 3M ohms
X
*1 Replace engine oil anf filter at 100 hours, first time only.
*2 Replace fuel filter at 250 Hours, first time only.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 41
DCA-15SPX3 —GENERATOR WIRING DIAGRAM
PAGE 42 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 —ENGINE WIRING DIAGRAM
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 43
DCA-15SPX3 — TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
diagnosis based on the Engine Troubleshooting (Table 11)
information shown below and on the proceeding page. If the
problem cannot be remedied, please consult our company's
business office or service plant.
TABLE 11. ENGINE TROUBLESHOOTING
SYMPTOM
Engine does not start.
Engine will not crank.
POSSIBLE PROBLEM
SOLUTION
No fuel?
Replenish fuel.
Air in the fuel system?
Bleed system.
Water in the fuel system?
Remove water from fuel tank.
Fuel pipe clogged?
Clean fuel pipes.
Fuel filter clogged?
Clean or change fuel filter.
Excessively high viscosity of fuel
or engine oil at low temperature?
Use the specified fuel or engine oil.
Fuel with low cetane number?
Use the specified fuel.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Incorrect injection timing?
Adjust.
Fuel cam shaft worn?
Replace.
Injection nozzle clogged?
Clean injection nozzle.
Injection pump malfunctioning?
Repair or replace.
Seizure of crankshaft, camshaft,
piston, cylinder liner or bearing?
Repair or replace.
Compression leak from cylinder?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
Improper valve timing?
Correct or replace timing gear.
Piston ring and liner worn?
Replace.
Excessive valve clearance?
Adjust.
Battery discharged?
Charge battery.
Starter malfunctioning?
Repair or replace.
Wiring disconnected?
Connect wiring.
PAGE 44 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — TROUBLESHOOTING (ENGINE)
TABLE 11. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
Engine revolution is not smooth.
Either white or blue exhaust gas
is observed.
Either black or dark gray exhaust
gas is observed.
Deficient output.
POSSIBLE PROBLEM
SOLUTION
Fuel filter clogged or dirty?
Clean or change.
Air cleaner clogged?
Clean or change.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Injection pump malfunctioning?
Repair or replace.
Incorrect nozzle opening
pressure?
Adjust.
Injection nozzle stuck or
clogged?
Repair or replace.
Fuel over flow pipe clogged?
Clean.
Governor malfunctioning?
Repair.
Excessive engine oil?
Reduce to the specified level.
Piston ring and liner worn or
stuck?
Repair or replace.
Incorrect injection timing?
Adjust.
Deficient compression?
Adjust top clearance.
Overload?
Lessen the load.
Low grade fuel used?
Use the specified fuel.
Fuel filter clogged?
Clean or change.
Air cleaner clogged?
Clean or change.
Deficient nozzle injection?
Repair or replace the nozzle.
Incorrect injection timing?
Adjust.
Engine's moving parts seem to
be seizing?
Repair or replace.
Uneven fuel injection?
Repair or replace the injection pump.
Deficient nozzle injection?
Repair or replace the nozzle.
Compression leak?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 45
DCA-15SPX3 — TROUBLESHOOTING (GENERATOR)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
diagnosis based on the Generator Troubleshooting (Table 12)
information shown below and on the proceeding page. If the
problem cannot be remedied, please consult our company's
business office or service plant.
TABLE 17. GENERATOR TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
AC Voltmeter defective?
Check output voltage using a voltmeter.
Is wiring connection loose?
Check wiring and repair.
Is AVR defective?
Replace if necessary.
Defective Rotating Rectifier?
Check and replace.
Is engine speed correct?
Turn engine throttle lever to "High".
Is wiring connections loose?
Check wiring and repair.
Defective AVR?
Replace if necessary.
Is wiring connections loose?
Check wiring and repair.
Defective AVR?
Replace if necessary.
Short Circuit in load?
Check load and repair.
Over current?
Confirm load requirements and reduce.
Defective circuit breaker?
Check and replace.
Over current Relay actuated?
Confirm load requirement and replace.
No Voltage Output
Low Voltage Output
High Voltage Output
Circuit Breaker Tripped
PAGE 46 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
NOTE PAGE
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 47
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #, +, %, or
■, belong to the same assembly or kit.
*
Note: If more than one of the same reference number is listed,
the last one listed indicates newest (or latest) part available.
NOTE
The contents of this parts catalog are
subject to change without notice.
PAGE 48 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — SUGGESTED SPARE PARTS
DCA-15SPX3 W/KUBO
TA V2203 DIESEL ENGINE 1 TO 3 UNITS
W/KUBOT
Qty.
P/N
Description
1 ......... 0601820626 ......................... AUTOMATIC VOLTAGE REGULATOR
1 ......... 0601806592 ......................... MAIN CIRCUIT BREAKER
1 ......... 0601802609 ......................... RECEPTACLE CIRCUIT BREAKER
1 ......... 0601840073 ......................... VOLTAGE REGULATOR (RHEOSTAT)
3 ......... 700003209 ........................... OIL FILTER
1 ......... 1584139010 ......................... OIL SWITCH
1 ......... 1726697011 ......................... FAN BELT
3 ......... 113043002 ........................... AIR FILTER
3 ......... 7000043081 ......................... FUEL FILTER
1 ......... 1706372940 ......................... RADIATOR HOSE, UPPER
1 ......... 1546172851 ......................... RADIATOR HOSE, LOWER
1 ......... 1949883040 ......................... WATER TEMPERATURE SENDING UNIT
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 49
DCA-15SPX3 — GENERATOR ASSY.
GENERATOR ASSY.
PAGE 50 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — GENERATOR ASSY.
GENERATOR ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PART NO.
7671000102
7961025004
0601822643
8001070003
8351611004
8351612004
8351615003
0010310025
0042610000
0601000209
0071906308
0070506903
0012108035
0042508000
7671345203
0845041904
8431350003
0016008045
0042508000
8351315003
011208035
8351312004
8351331004
0017106016
012010030
030210250
8401332004
0010106030
952404470
0605000006
0207010000
PART NAME
QTY.
REMARKS
ROTOR ASSY.
1
FIELD ASSY.
1
RECTIFIER
1
SURGE ABSORBER ................................... 1 ............. TNR23G561K
FAN
1
COUPLING DISK
2
WASHER, COUPLING HUB
1
BALANCING PLATE
1
HEX. HEAD BOLT
4
LOCK WASHER
4
BALANCING WEIGHT KIT
1
BEARING .................................................... 1 ............. 6308DDUC3
BEARING .................................................... 1 ............. 6903ZZ
HEX. HEAD BOLT
6
LOCK WASHER
6
STRATOR ASSY.
1
GROMMET
1
FIELD ASSY. EXCITER
1
HEX. SOCKET HEAD CAP SCREW
3
LOCK WASHER
3
END BRACKET
1
HEX.HEAD BOLT ........................................ 6 ............. REPLACES 0017108035
PACKING
1
COVER, SUCTION
1
HEX. HEAD BOLT
3
HEX. HEAD BOLT ....................................... 6 ............. REPLACES 0012110030
LOCK WASHER ........................................... 6 ............. REPLACES 0042510000
COVER, FAN
1
HEX. HEAD BOLT
1
PLAIN WASHER .......................................... 1 ............. REPLACES 0041206000
RUBBER SUSPENSION
2
HEX. NUT
2
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 51
DCA-15SPX3 — CONTROL BOX ASSY.
CONTROL BOX ASSY.
PAGE 52 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
PART NO.
7671821603
0605010060
0021103010
0601800455
0601805746
0601800281
0601840073
0601840121
0601802609
4341817004
0027104020
0207004000
0602100059
0601810523
0601810830
0601800682
0021806030
0601806592
0021004060
0040004000
0041204000
0601801122
0027106016
0601842304
0027104012
0601820038
0027104020
0601820626
0017105016
0601815759
0027104020
0602200474
0021005045
0040005000
0041205000
8701899004
0601806642
0601806643
0601806644
0027105016
0602201273
0602202566
0017105016
0601806640
0601842389
PART NAME
QTY. REMARKS
CONTROL PANEL
1
HINGE ...................................................... 2 ........ B1075L
MACHINE SCREW
8
FREQUENCY METER ............................. 1 ........ FCF5 240V 45Hz~65Hz
AC AMMETER ......................................... 1 ........ ACF5 0~100A
AC VOLTMETER ...................................... 1 ........ SCF5 0~150V 0~300V
RHEOSTAT (VOLTAGE REGULATOR) ..... 1 ........ RA20A2SE102BJ 2W 1kOHM
KNOB
1
CIRCUIT BREAKER ................................ 1 ........ KM2 50A
BRACKET, CIRCUIT BREAKER
1
MACHINE SCREW
2
HEX. NUT
2
STARTER SWITCH .................................. 1 ........ 3741059113
INDICATOR ASSY. ................................... 1 ........ PLB128Q
BULB
4
HOUR METER ......................................... 1 ........ 82014
MACHINE SCREW
2
CIRCUIT BREAKER ................................ 1 ........ SC100CS 65A
MACHINE SCREW
2
LOCK WASHER
2
PLAIN WASHER
2
CURRENT TRANSFORMER, AMMETER 1 ........ COC3 100A/5A
MACHINE SCREW
2
RESISTOR ............................................... 1 ........ GG20W50OHM
MACHINE SCREW
2
RECTIFIER .............................................. 1 ........ S15VB60
MACHINE SCREW
1
AUTOMATIC VOLTAGE REGULATOR ...... 1 ........ NTA4A25
HEX. HEAD BOLT
4
TERMINAL BOARD ................................. 1 ........ KT206P
MACHINE SCREW
2
EMERGENCY UNIT ................................. 1 ........ 1714760602
MACHINE SCREW
2
LOCK WASHER
2
PLAIN WASHER
2
FUSE BOX ............................................... 1 ........ FB6PS
FUSE ....................................................... 4 ........ 5A
FUSE ....................................................... 2 ........ 15A
FUSE ....................................................... 2 ........ 30A
MACHINE SCREW
2
TIMER ...................................................... 1 ........ 1569465992
RELAY ..................................................... 1 ........ 6888153542
HEX. HEAD BOLT
2
FUSE ....................................................... 1 ........ 65A
RESISTOR ............................................... 1 ........ 8.2OHM 1/2W
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 53
DCA-15SPX3 — OUTPUT TERMINAL ASSY.
OUTPUT TERMINAL ASSY.
PAGE 54 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — OUTPUT TERMINAL ASSY.
OUTPUT TERMINAL ASSY.
NO.
PART NO.
PART NAME
1
2
3
4
5
6
7
8
9
10
11
11-1
12
13
14
15
16
17
18
19
20
21
7561860104
1621849004
0019008020
0040008000
0041408000
0039508000
0030008000
7831860104
0017106025
0601815109
7671865403
7671865804
0017106020
0821800014
0805088004
0207006000
0017106016
0601812597
0601811031
0601811033
0601812565
0027104016
0207004000
7672142003
0805012904
7672144103
3032143004
8322145004
0017110015
SET BOARD, OUTPUT TERMINAL 1
OUTPUT TERMINAL
3
HEX. HEAD BOLT
3
LOCK WASHER
9
PLAIN WASHER
9
HEX. NUT
3
HEX. NUT
3
RUBBER SEAL
1
HEX. HEAD BOLT
4
GROUND TERMINAL .......................... 1
COVER, GROUND TERMINAL
1
RUBBER SHEET
1
HEX. HEAD BOLT
2
COLLAR
2
STAY RUBBER
1
HEX. NUT
1
HEX. HEAD BOLT
1
RECEPTACLE ...................................... 1
RECEPTACLE ...................................... 1
RECEPTACLE ...................................... 1
RECEPTACLE ...................................... 1
MACHINE SCREW
8
HEX. NUT
8
SLIDE LEVER
1
KNOB
1
THROTTLE CABLE
1
SPRING
1
BRACKET
1
HEX. HEAD BOLT
2
22
23
24
25
26
27
QTY.
REMARKS
............T381
............520R 125V 20A
............L530R 125V 30A
............L630R 250V 30A
............CS6369 125/250V 50A
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 55
DCA-15SPX3 — ENGINE & RADIATOR ASSY.
ENGINE & RADIATOR ASSY.
PAGE 56 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — ENGINE & RADIATOR ASSY.
ENGINE & RADIATOR ASSY.
NO.
1
1-1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
43
44
45
46
PART NO.
7670150204
1732132432
1707972063
8345112004
8345112204
011006010
011008020
8345127103
8345127504
8345127604
011006010
0017106016
1542872941
1542872852
1510872873
113R60000B
113043002
8722031503
011208030
8432031104
011008020
8322036103
8432036103
0605515001
8325112114
8325112014
0012410025
0012412025
7605419004
0207010000
1502025004
0602021193
1502025103
0802011104
0150000018
0017106016
0192200430
0605515003
1546173341
1718273341
0605515014
0802081403
0802081104
0017106035
1559672711
7222016304
0605515094
PART NAME
QTY.
REMARKS
ENGINE .......................................... 1 .......... KUBOTA V2203
CARTRIDGE, OIL FILTER .............. 1 .......... REPLACES 0602041173
RADIATOR ...................................... 1 .......... REPLACES 0602011877
BRACKET, RADIATOR
1
BRACKET, RADIATOR
1
HEX. HEAD BOLT ........................... 6 .......... REPLACES 0017106010
HEX. HEAD BOLT ........................... 4 .......... REPLACES 0017108020
FAN GUARD
1
BRACKET, FAN GUARD
1
BRACKET, FAN GUARD
1
HEX. HEAD BOLT ........................... 4 .......... REPLACES 0017106010
HEX. HEAD BOLT
4
RADIATOR HOSE ........................... 1 .......... REPLACES 0602014560
RADIATOR HOSE ........................... 1 .......... REPLACES 0602014477
HOSE BAND ................................... 4 .......... REPLACES 0602014372
AIR CLEANER ................................ 1 .......... REPLACES 0602046268
ELEMENT, AIR CLEANER .............. 1 .......... REPLACES 0602046335
BAND, AIR CLEANER
1
HEX. HEAD BOLT ........................... 1 .......... REPLACES 0017108030
BRACKET, AIR CLEANER
1
HEX. HEAD BOLT ........................... 4 .......... REPLACES 0017108020
HOSE, AIR CLEANER
1
HOSE, AIR CLEANER
1
HOSE BAND
3
ENGINE FOOT
1
ENGINE FOOT
1
HEX. HEAD BOLT
1
HEX. HEAD BOLT
7
RUBBER SUSPENSION
2
HEX. NUT
2
DRAIN JOINT
1
PACKING ........................................ 1 .......... SW16
DRAIN JOINT
2
PLUG
2
O RING ........................................... 2 .......... AP18
HEX. HEAD BOLT
4
DRAIN HOSE
1
HOSE BAND
2
HOSE .............................................. 1 .......... REPLACES 0602014476
DRAIN HOSE .................................. 1 .......... REPLACES 0602014661
HOSE BAND
4
RESERVE TANK
1
CAP, RESERVE TANK
1
HEX. HEAD BOLT
1
HOSE .............................................. 1 .......... REPLACES 0602014173
HOSE
1
HOSE BAND
3
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 57
DCA-15SPX3 — BATTERY ASSY.
BATTERY ASSY.
PAGE 58 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — BATTERY ASSY.
BATTERY ASSY.
NO. PART NO.
1 0167306531
2 8452250003
8345967004
3 0017106016
4 7612251004
5 8432255024
6 8432256024
7 0017106016
8 8432256104
9 0037806000
10 0040006000
11 952404470
12 N012CABLE10SPX3
13 N013CABLE10SPX3
14 EARTH10SPX3
15 0602220310
16 0602220311
17 0602220600
PART NAME
QTY.
REMARKS
BATTERY
1
65D31R
BATTERY FRAME
1
LINING
1
HEX HEAD BOLT
5
BATTERY SHEET
1
BATTERY BAND
1
BATTERY BOLT
1
HEX HEAD BOLT
2
BATTERY BOLT
1
WING NUT
2
SPRING WASHER
2
PLAIN WASHER ............2 ............... REPLACES 0041206000
BATTERY CABLE
1
BATTERY CABLE
1
EARTH CABLE
1
TERMINAL ASS’Y. ........ 1 ............... NO.9P
TERMINAL ASS’Y. ........ 1 ............... NO.9N
TERMINAL CAP ............1 ............... 7C7R
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 59
DCA-15SPX3 — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 60 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
2
3
4
5
6
7
PART NO.
8342311003
011008020
8342350103
T007016420
1502336004
020108060
011208035
PART NAME
QTY.
REMARKS
MUFFLER
1
HEX HEAD BOLT ........................... 6 .......... REPLACES 0017108020
EXHAUST PIPE
1
GASKET ......................................... 1 .......... REPLACES 0602320150
GASKET
1
HEX NUT ........................................ 4 .......... REPLACES 0207008000
HEX HEAD BOLT ........................... 2 .......... REPLACES 0017108035
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 61
DCA-15SPX3 — FUEL TANK ASSY.
FUEL TANK ASSEMBLY
PAGE 62 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — FUEL TANK ASSY.
FUEL TANK ASSEMBLY
NO.
1
1-1
1-2
1-3
1-4
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
PART NO.
7675510703
0810105800
0810105900
0267700245
0605515191
8435525003
011008020
1555527004
8435523014
0805003404
011008020
0207308000
7812014003
0802011104
0150000018
0017106016
019900640
0605515094
1522143016
1522143172
7675528004
0017108035
0017108025
0207008000
0603325013
0602022708
0966180180
0966180340
0966140180
1491142751
1497142751
1615511204
PART NAME
QTY. REMARKS
FUEL TANK
1
CAP, FUEL TANK
1
FUEL FILTER
1
HOSE, FUEL GAUGE
1
HOSE BAND
2
BRACKET. FUEL TANK
1
HEX. HEAD BOLT ....................................... 4...... REPLACES 0017108020
TANK SHEET
2
TANK BAND
2
PAD, TANK BAND
4
HEX. HEAD BOLT ....................................... 2...... REPLACES 0017108020
HEX. NUT
2
DRAIN JOINT
1
PLUG
1
O RING ....................................................... 1...... AP18
HEX. HEAD BOLT
2
DRAIN HOSE
1
HOSE BAND
2
FUEL FILTER .............................................. 1...... REPLACES 0602042462
ELEMENT, FUEL FILTER ........................... 1...... REPLACES 0602042551
BRACKET, FUEL FILTER
1
HEX. HEAD BOLT
2
HEX. HEAD BOLT
2
HEX. NUT
2
FUEL COCK, 3/8
1
HOSE, JOINT ............................................. 1...... WHN8
SUCTION HOSE ......................................... 1...... REPLACES 0605513116
SUCTION HOSE ......................................... 1...... REPLACES 0605513117
RETURN HOSE .......................................... 1...... REPLACES 0605514026
HOSE BAND ............................................... 4...... REPLACES 0605515070
HOSE BAND ............................................... 1...... REPLACES 0605515072
RUBBER SEAL
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 63
DCA-15SPX3 — ENCLOSURE ASSY.
ENCLOSURE ASSEMBLY
PAGE 64 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — ENCLOSURE ASSY.
ENCLOSURE ASSEMBLY
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
PART NO.
7675111602
8445116114
0017106016
7675121202
8345921204
8345924004
011008020
1625165103
1625165204
011008020
8342313003
8345925004
011008020
8435125004
8345923004
011008020
8345130203
8435132113
012212030
7675141802
011008020
8345144604
8345143203
8345943004
0207006000
011008020
7675146103
8435149004
0207006000
0605010230
0021805012
PART NAME
QTY.
REMARKS
BASE
1
FLOOR PANEL
1
HEX. HEAD BOLT
8
FRONT FRAME
1
ACOUSTIC SHEET
1
ACOUSTIC SHEET
1
HEX. HEAD BOLT ................................ 7 ............. REPLACES 0017108020
FILLER COVER
1
CHAIN
1
HEX. HEAD BOLT ................................ 1 ............. REPLACES 0017108020
COVER, MUFFLER
1
ACOUSTIC SHEET
1
HEX. HEAD BOLT ................................ 4 ............. REPLACES 0017108020
COVER, FRONT FRAME
1
ACOUSTIC SHEET
1
HEX. HEAD BOLT ................................ 6 ............. REPLACES 0017108020
HANGER
1
HANGER
1
HEX. HEAD BOLT ................................ 6 ............. REPLACES 0017112030
REAR FRAME
1
HEX. HEAD BOLT ................................ 7 ............. REPLACES 0017108020
COVER, REAR FRAME
1
DUCT
1
ACOUSTIC SHEET
1
HEX. NUT
4
HEX. HEAD BOLT ................................ 6 ............. REPLACES 0017108020
DOOR, REAR FRAME
1
WINDOW PLATE
1
HEX. NUT
8
DOOR HANDLE
1
MACHINE SCREW
4
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1- ORANGE
6 -CATERPILLAR YELLOW
2- WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 65
DCA-15SPX3 — ENCLOSURE ASSY.
ENCLOSURE ASSEMBLY
PAGE 66 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — ENCLOSURE ASSY.
ENCLOSURE ASSEMBLY
NO.
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
PART NO.
0810015204
0810015504
0017106016
8345161302
8345961304
011008020
8345172103
8345972204
8345173104
0207006000
011208035
8345170203
8345970504
8435170203
8345970404
8345171114
0207006000
B9114000002
0021806016
8435149104
0027103010
0207003000
M9110100304
0845045004
M911B110204
0845045004
011008020
0845031504
0601851613
0600500090
0021106016
PART NAME
QTY.
REMARKS
HINGE
2
WASHER
2
HEX. HEAD BOLT
4
ROOF PANEL
1
ACOUSTIC SHEET
1
HEX. HEAD BOLT .............................. 16 ............. REPLACES 0017108020
SIDE PANEL
1
ACOUSTIC SHEET
1
DUCT
1
HEX. NUT
5
HEX. HEAD BOLT ................................ 6 ............. REPLACES 0017108035
SIDE DOOR
1
ACOUSTIC SHEET
1
SIDE DOOR
1
ACOUSTIC SHEET
1
DUCT
1
HEX. NUT
7
DOOR HANDLE
1
MACHINE SCREW
4
WINDOW PLATE
1
MACHINE SCREW
4
HEX. NUT
4
HINGE .................................................. 2 ............. REPLACES 0845047204
WASHER
2
HINGE .................................................. 2 ............. REPLACES 0845047104
WASHER
2
HEX. HEAD BOLT ................................ 8 ............. REPLACES 0017108020
CAP
4
STOPPER ............................................ 2 ............. CP30FF15A
EMBLEM
1
MACHINE SCREW
2
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 67
DCA-15SPX3 — ENCLOSURE (RUBBER SEALS) ASSY.
ENCLOSURE (SEALS )ASSY.
PAGE 68 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — ENCLOSURE (RUBBER SEALS) ASSY.
ENCLOSURE (RUBBER SEALS )ASSY.
NO.
1
2
3
4
5
6
7
8
9
PART NO.
0229400650
0229400895
0229200650
0220400650
0227600895
0229400265
0229400550
0229200580
0229200245
PART NAME
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
QTY.
3
2
1
2
2
2
1
2
2
REMARKS
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 69
DCA-15SPX3 — NAME PLATE AND DECALS
NAME PLATE AND DECALS
PAGE 70 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
DCA-15SPX3 — NAME PLATE AND DECALS
NAME PLATE AND DECALS
NO.
1
2
3
4
5
6
7
8
9
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
27
28
29
30
31
32
33
34
35
36
37
38
PART NO.
0800628504
1630610304
1630610504
1320620904
0800650804
6360610304
6360620004
6360620104
6360620204
6360620204
0800689404
0800689504
1320621504
6390671104
0840624504
0840625902
1980680004
7670623004
7670624004
7670622004
7670654004
7670650004
7560615004
8700611804
8700611904
7670630103
0820610404
0820650604
8700625504
7670633003
7670633104
7670633604
7670633704
7670633204
7670633504
7670633404
7670633304
7670633804
PART NAME
QTY.
REMARKS
DECAL; GROUND ................................... 1 ............ S1123
DECAL; DANGER ................................... 1 ............ S1405
DECAL; CAUTION ................................... 1 ............ S1409
DECAL; DIESEL FUEL ........................... 1 ............ S1756
DECAL; FUEL GAUGE ............................ 1 ............S1765
DECAL; WATER ...................................... 1 ............ S1880
DECAL; FUEL DRAIN PLUG ................... 1 ............ S1883
DECAL; WATER DRAIN PLUG ................ 1 ............ S1884
DECAL; OIL DRAIN PLUG ...................... 1 ............ S1884
DECAL; OIL DRAIN PLUG ...................... 1 ............ S1885
DECAL; + ................................................ 1 ............ S2090
DECAL; - ................................................ 1 ............ S2091
DECAL; SUPPORT HOOK ...................... 2 ............ S2257
DECAL; IMPORTANT "CHECK DAILY" ... 1 ............S2377
DECAL; CIRCUIT BREAKER .................. 2 ............ S3031
DECAL; MQ ............................................ 1 ............ S3057
DECAL; FUEL COCK .............................. 1 ............ S3704
DECAL; VOLTAGE REGULATOR ............. 1 ............ S3737
DECAL; GROUND FOR GFCI ................. 1 ............ S3821
DECAL; SPEED CONTROL HANDLE ..... 1 ............ S3822
DECAL; AC OUTPUT TERMINAL ........... 1 ............ S3823A
DECAL; DANGER HIGH VOLTAGE ......... 1 ............S3956
DECAL; STARTER SWITCH ................... 1 ............ S4547
DECAL; WARNING .................................. 1 ............ S4984
DECAL; DANGER ................................... 1 ............ S4985
DECAL; AC POWER OUTPUT ............... 1 ............ S5272
DECAL; WARNING
1
DECAL; DANGER
1
DECAL; FUSE BOX
1
STRIPE
1
STRIPE
1
STRIPE
1
STRIPE
1
STRIPE
1
STRIPE
1
STRIPE
1
STRIPE
1
STRIPE
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 71
KUBOTA V2203 - ENGINE — CRANKCASE ASSY.
CRANKCASE ASSY.
PAGE 72 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — CRANKCASE ASSY.
CRANKCASE ASSY.
NO.
010
015#
020#
030#
040#
050#
060#
070#
080#
090#
100#
110#
120#
130#
150
160
170
180
190
200
210
220
230
240
250
260
PART NO.
1649401010
3415027580
3221027580
1552196020
1552196030
1739196160
0631175045
1522103380
1522103390
0501200408
0501200609
0501200512
0501201018
1522133650
1522133610
1502133660
1522133700
1532173340
1547135010
1520635150
0105350650
0451260060
1920235660
0571200410
1522135682
1584139010
PART NAME
QTY. REMARKS
COMP. CRANKCASE ..................... 1 ....... INCL. ITEMS W/#
PLUG
1
PLUG
2
PLUG
6
PLUG
2
EXPANSION PLUG
3
EXPANSION PLUG
1
SEALING CAP
6
SEALING CAP
2
STRAIGHT PIN
2
STRAIGHT PIN
2
STRAIGHT PIN
2
STRAIGHT PIN
1
PIPE PIN
1
PLUG
1
GASKET
1
O RING
1
WATER RETURN PIPE
1
OIL PUMP ASSY.
1
OIL PUMP GASKET
1
BOLT
4
SPRING WASHER
4
OIL PUMP DRIVE GEAR
1
FEATHER KEY
1
FLANGE NUT
1
OIL SWITCH
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 73
KUBOTA V2203 - ENGINE — OIL PAN ASSY.
OIL PAN ASSY.
PAGE 74 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — OIL PAN ASSY.
OIL PAN ASSY.
NO.
010
020
030
040
050
060
070
080
090
100
110
PART NO.
1543401613
1922801620
1733391010
1522133750
1510933660
1595133750
0472400160
1562832110
0112360816
0481100160
1711136410
PART NAME
OIL PAN
OIL PAN GASKET
FLANGE BOLT
PLUG
GASKET
DRAIN PLUG
GASKET
OIL FILTER
BOLT
O RING
OIL GAUGE
QTY. REMARKS
1
1
24
1
1
1
1
1
1
1
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 75
KUBOTA V2203 - ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 76 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
010
020
030
040
050
060
070
080
090#
100#
110#
120#
130#
150
160
170
PART NO.
1641501752
1522101750
0112360816
1522191530
0215650080
0451260080
0401250080
1907703045
1522103370
1522103490
1526196010
1732113580
1732113560
1901303450
1907703310
1949883040
PART NAME
QTY. REMARKS
ENGINE HOOK
1
ENGINE HOOK
1
BOLT
1
STUD
1
NUT
1
SPRING WASHER
1
PLAIN WASHER
1
COMP. CYLINDER HEAD .............. 1 ..... INCL. ITEMS W/#
SEALING CAP
12
SEALING CAP
1
PLUG
2
INLET VALVE GUIDE
4
EXHAUST VALVE GUIDE
4
CYLINDER HEAD BOLT
18
CYLINDER HEAD GASKET
1
THERMOSWITCH, ASSY.
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 77
KUBOTA V2203 - ENGINE — GEAR CASE ASSY.
GEAR CASE ASSY.
PAGE 78 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — GEAR CASE ASSY.
GEAR CASE ASSY.
NO.
010
020#
030#
040#
050#
060#
070
080
090
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
250
260
270
280
290
300
310
PART NO.
1718204010
1685196010
0481100150
0481100360
1981856280
0501200612
1708904130
0112350860
0115350870
1736791030
0115350880
1736791020
0115350895
0451260080
0401250080
1552132290
0401150180
1524136950
1552136930
0771503213
1552173320
1576673330
0102350620
1732132430
1585233140
0481150300
1718233110
1547154550
1718291510
0451260060
0205650060
PART NAME
QTY. REMARKS
GEAR CASE ASSY ....................... 1 ....... INCL. ITEMS W/#
PLUG
2
O RING
3
O RING
1
START SPRING PIN
1
STRAIGHT PIN
2
GEAR CASE GASKET
1
BOLT
2
BOLT
5
BOLT
1
BOLT
2
BOLT
3
BOLT
2
SPRING WASHER
10
PLAIN WASHER
1
PIPE JOINT
1
PLAIN WASHER
1
SPRING
1
VALVE SEAT
1
BALL
1
WATER RETURN FLANGE
1
GASKET
1
BOLT
3
OIL FILTER CARTRIDGE
1
OIL FILTER PLUG
1
O RING
1
OIL FILTER FLANGE
1
BOOST BASE C. GASKET
1
STUD
4
SPRING WASHER
4
NUT
4
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 79
KUBOTA V2203 - ENGINE — MAIN BEARING CASE ASSY.
MAIN BEARING CASE ASSY.
PAGE 80 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — MAIN BEARING CASE ASSY.
MAIN BEARING CASE ASSY.
NO.
010
020
030
040
050
060
070
080
090
100
110
120
PART NO.
1901304090
1901304540
1907704360
1901304813
1711804830
0112350825
0112350828
1920204460
1901304040
1901304050
1901304060
1560104560
PART NAME
MAIN BEARING CASE ASSY.
BEARING CASE BOLT
BEARING CASE GASKET
BEARING CASE COVER
CASE COVER GASKET
BOLT
BOLT
OIL SEAL
MAIN BEARING CASE ASSY.
MAIN BEARING CASE ASSY.
MAIN BEARING CASE ASSY.
BEARING CASE BOLT
QTY.
1
8
1
1
1
8
8
1
1
1
1
3
REMARKS
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 81
KUBOTA V2203 - ENGINE — HEAD COVER ASSY.
HEAD COVER ASSY.
PAGE 82 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — HEAD COVER ASSY.
HEAD COVER ASSY.
NO.
010
020
030
040
050
060
070
080
090
100
110
PART NO.
1711414510
1547114520
1718205020
1711405130
0112350840
1624105670
1718214490
1718205510
0931888200
1545192330
1502133660
PART NAME
HEAD COVER
HEAD COVER GASKET
COMP BREATHER
GASKET
BOLT
BREATHER ELEMENT
PLATE
BREATHER TUBE
HOSE CLAMP
CAP NUT
GASKET
QTY.
1
1
1
2
2
1
1
1
2
4
4
REMARKS
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 83
KUBOTA V2203 -ENGINE — INLET MANIFOLD ASSY.
INLET MANIFOLD ASSY.
PAGE 84 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 -ENGINE — INLET MANIFOLD ASSY.
INLET MANIFOLD ASSY.
NO.
010
020
030
040
PART NO.
1711411760
1718205550
1642311820
0112350822
PART NAME
INLET MANIFOLD
BREATHER JOINT
IN - MANIFOLD GASKET
BOLT
QTY.
1
1
1
7
REMARKS
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 85
KUBOTA V2203 - ENGINE — EXHAUST MANIFOLD ASSY.
EXHAUST MANIFOLD ASSY.
PAGE 86 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — EXHAUST MANIFOLD ASSY.
EXHAUST MANIFOLD ASSY.
NO.
010
020
030
040
050
060
PART NO.
1737712312
1552212350
1522191530
1642992010
0151350822
T007016420
PART NAME
EXHAUST MANIFOLD
EX-MANIFOLD GASKET
STUD
NUT
STUD
MUFFLER GASKET
QTY.
1
4
8
8
4
1
REMARKS
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 87
KUBOTA V2203 -EB ENGINE — VALVE AND ROCKER ASSY.
VALVE AND ROCKER ASSY.
PAGE 88 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 -EB ENGINE — VALVE AND ROCKER ASSY.
VALVE AND ROCKER ASSY.
NO.
010
020
030
040
050
060
070
080
090#
100
110
120
130
140
150
160
170
180
190
200*
210*
PART NO.
1648413110
1648413120
1522113240
1522113330
1522113360
1522113150
1522113280
1540114052
0341000808
1522114350
1552191500
0215650080
0451260080
0401250080
0541100528
1522114430
1522114310
0461200140
1562114030
1552114230
1502114240
PART NAME
QTY. REMARKS
INLET VALVE
4
EXHAUST VALVE
4
VALVE SPRING
8
VALVE SPRING RETAINER
8
VALVE SPRING COLLAR .............. 8 ....... SET
VALVE STEM SEAL
8
VALVE CAP
8
ROCKER ARM SHAFT ASSY.
1
SET SCREW .................................. 2 ....... INCLUDES ITEM W/#
ROCKER ARM BRACKET
4
STUD
4
NUT
4
SPRING WASHER
4
PLAIN WASHER
4
SPRING PIN
1
ROCKER ARM SHAFT WASHER 2
ROCKER ARM SPRING
3
EXTERNAL CIR CLIP
2
ROCKER ARM ASSY. .................... 8 ....... INCLUDES ITEM W/*
ADJUSTING SCREW
8
NUT
8
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 89
KUBOTA V2203 - ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 90 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
010
020
030
040#
050#
060#
070#
080#
090
100
110*
120
130
140
150
160
PART NO.
1560115550
1901315110
1734316010
1734316150
1552193610
1552116510
0571200720
1522116270
0112350818
1522124010
1733124980
1552124360
1552124370
1522124320
1981824250
0112350818
PART NAME
QTY. REMARKS
TAPPET
8
PUSH ROD
8
CAMSHAFT ASSY. ........................ 1 ....... INCLUDES ITEMS W/#
CAMSHAFT
1
SET SCREW
1
CAM GEAR
1
FEATHER KEY
1
CAMSHAFT STOPPER
1
BOLT
2
IDLE GEAR COMP. ........................ 1 ....... INCLUDES ITEMS W/*
IDLE GEAR BUSH
1
COLLAR
1
COLLAR
1
IDLE GEAR CIR CLIP
1
IDLE GEAR SHAFT
1
BOLT
3
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 91
KUBOTA V2203 - ENGINE — PISTON AND CRANKSHAFT ASSY.
PISTON AND CRANKSHAFT ASSY.
PAGE 92 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — PISTON AND CRANKSHAFT ASSY.
PISTON AND CRANKSHAFT ASSY.
NO.
010
010
020
030
040
050
060*
070*
080*
080
080
090
100#
110#
120
130
140
150
160
170
180
180
180
190
190
190
200
200
200
210
210
210
220
PART NO.
1907721110
1907721910
1733121050
1490121310
1410921330
1731122010
1733121980
1552122142
1731122310
1733122970
1733122980
1664123010
0771500401
1920223280
1547124110
0571200720
1547123312
1920223250
0481110300
1522123360
1731123470
1731123910
1731123920
1731123480
1731123930
1731123940
1552123530
1522123950
1522123960
1920223540
1920223970
1920223980
1920204140
PART NAME
QTY. REMARKS
PISTON .......................................... 4 ....... S T D
PISTON .......................................... 4 ....... + 0.5 M M
PISTON RING ASSY.
4
PISTON PIN
4
PISTON PIN CLIP
8
CONNECTING ROD ASSY. ............ 4 ....... INCLUDES ITEMS W/*
PISTON PIN BUSH
4
CONNECTING ROD BOLT
8
CRANKPIN METAL ........................ 4 ....... STD SET
CRANKPIN METAL ........................ 4 ....... - 0.20 M M SET
CRANKPIN METAL ........................ 4 ....... - 0.40 M M SET
COMP. CRANKSHAFT ................... 1 ....... INCLUDES ITEMS W/#
BALL
4
CRANKSHAFT BUSHING
1
CRANK GEAR
1
FEATHER KEY
1
OIL SLINGER
1
CRANKSHAFT COLLAR
1
O RING
1
CRANKSHAFT NUT
1
CRANKSHAFT METAL ................... 1 ....... STD
CRANKSHAFT METAL ................... 1 ....... - 0.20 M M
CRANKSHAFT METAL ................... 1 ....... - 0.40 M M
CRANKSHAFT METAL ................... 4 ....... STD SET
CRANKSHAFT METAL ................... 4 ....... - 0.20 M M SET
CRANKSHAFT METAL ................... 4 ....... - 0.40 M M SET
SIDE METAL .................................. 2 ....... STD
SIDE METAL .................................. 2 ....... + 0.20 M M
SIDE METAL .................................. 2 ....... + 0.40 M M
SIDE METAL .................................. 2 ....... STD
SIDE METAL .................................. 2 ....... + 0.20 M M
SIDE METAL .................................. 2 ....... + 0.40 M M
OIL SEAL
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 93
KUBOTA V2203 -ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 94 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
010
020*
030
040
050
060
070
080
090
100
110
120
PART NO.
1747525010
1560263820
1532125163
1747504610
1552104680
1552104790
0112360816
0107351032
0107351042
0451260100
0107351250
0451260120
PART NAME
COMP. FLYWHEEL
RING GEAR
FLYWHEEL BOLT
FLYWHEEL HOUSING
COVER
COVER PACKING
BOLT
BOLT
BOLT
SPRING WASHER
BOLT
SPRING WASHER
QTY.
1
1
6
1
1
1
2
11
3
11
2
2
REMARKS
INCLUDES ITEMS W/*
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 95
KUBOTA V2203 - ENGINE — STARTER ASSY. AND MOUNTING
STARTER ASSY.
PAGE 96 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — STARTER ASSY. AND MOUNTING
STARTER ASSY.
NO.
010
020
030
040
050
060
070
PART NO.
1738163012
0151751028
0113351030
0217650100
0451260100
0211450080
0451260080
PART NAME
STARTER ASSY.
STUD
BOLT
NUT
SPRING WASHER
NUT
SPRING WASHER
QTY.
1
1
1
1
1
1
1
REMARKS
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 97
KUBOTA V2203 - ENGINE — STARTER (COMPONENTS) ASSY.
STARTER (COMPONENTS) ASSY.
PAGE 98 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — STARTER (COMPONENTS) ASSY.
STARTER (COMPONENTS) ASSY.
NO.
010
020*
030*
040*#
050*#
060*
070*
080*
090*
100*
110*$
120*
130*
140*
150*
160*
170*
180*
190*
200*
210*
220*
PART NO.
1738163012
1119763080
1119763070
1146063500
1146063530
1562163040
1648463030
1648463020
1648463200
1738163380
1540163390
1146063270
1146063110
1921263100
1146063120
1921297130
1146093310
1551196660
1119763320
1551163760
1628563570
1396392010
PART NAME
QTY. REMARKS
STARTER ASSY. .......................... 1 ......... INCLUDES ITEMS W/*
YOKE ASSY.
1
ARMATURE ASSY. ...................... 1 ......... INCLUDES ITEMS W/#
BEARING
1
BEARING
1
OVER RUNNING CLUTCH
1
DRIVE END FRAME
1
MAGNETIC SWITCH
1
END FRAME
1
BRUSH HOLDER ASSY. .............. 1 ......... INCLUDES ITEMS W/$
BRUSH SPRING
4
GEAR
1
RETAINER
1
ROLLER
5
SPRING
1
BALL
1
BOLT
2
O RING
2
BOLT
2
BOLT ASSY.
2
DRAIN PIPE
1
HEXAGON NUT
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 99
KUBOTA V2203 - ENGINE — NOZZLE HOLDER ASSY.
NOZZLE HOLDER ASSY.
PAGE 100 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — NOZZLE HOLDER ASSY.
NOZZLE HOLDER ASSY.
NO.
010
020
030*
040*
050
060
065#
070#
080#
090
100
110
120
130
140
150
160
170
180
190
PART NO.
1645442502
1733142500
1497142750
1024442320
1524167580
1645453900
1645453610
1584153622
1907753650
1907753650
1907753723
1907753733
1907753743
1584153850
1584153860
0302450520
1907765510
1647565560
0401360040
0276150040
PART NAME
QTY. REMARKS
OVER FLOW PIPE ASSY.
1
OVER FLOW PIPE ASSY. ............. 1 ....... INCLUDES ITEMS W/*
PIPE CLIP
1
PIPE CLIP
1
CORD CLAMP
1
NOZZLE HOLDER KIT ................... 1 ....... INCLUDES ITEMS W/#
NOZZLE PIECE
4
GASKET
4
HEAT SEAL
4
INJECTION PIPE
1
INJECTION PIPE
1
INJECTION PIPE
1
INJECTION PIPE
1
PIPE CLAMP
3
PIPE CLAMP
3
WASHER WITH SCREW
3
GLOW PLUG
4
GLOW PLUG CORD
1
PLAIN WASHER
4
FLANGE NUT
4
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 101
KUBOTA V2203 - ENGINE — INJECTION PUMP 1 ASSY.
INJECTION PUMP 1 ASSY.
PAGE 102 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — INJECTION PUMP 1 ASSY.
INJECTION PUMP 1 ASSY.
NO.
010
020
030
040
050
060
070
080
090
100
120
130
140
150
160#
PART NO.
1667251010
1907752090
1907752110
1907752120
0112350822
1522191530
0215650080
0451260080
1574860570
1712152030
1526352140
0102350616
1540195690
1468142010
1430142750
PART NAME
QTY. REMARKS
INJECTION PUMP ASSY.
1
INJECTION SHIM
1
INJECTION SHIM
1
INJECTION SHIM
1
BOLT
4
STUD
2
NUT
2
SPRING WASHER
2
ORIFICE ASSY.
1
FUEL PUMP ASSY.
1
FUEL PUMP GASKET
1
BOLT
2
EYE JOINT
1
FUEL PIPE ASSY. ......................... 1 ....... INCLUDES ITEMS W/#
PIPE CLIP
2
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 103
KUBOTA V2203 - ENGINE — INJECTION PUMP 2 ASSY.
INJECTION PUMP 2 ASSY.
PAGE 104 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — INJECTION PUMP 2 ASSY.
INJECTION PUMP ASSY. 2
NO.
010
020*
030*
040*
050*
060*
070*
080*
090*
100*
110*
120*
130*
140*
150*
160*
170*
180*
190*
PART NO.
1667251010
1667251050
1647551030
1647551230
1142051240
1641551220
1647551610
1522151070
1461151250
1461151440
1522151280
1522151270
1522151290
1907751490
1540151060
1522151382
1547151382
1540196650
1461151200
PART NAME
QTY. REMARKS
INJECTION PUMP ASSY. ............. 1 ....... INCLUDES ITEMS W/*
PUMP PLUNGER
4
DELIVERY VALVE
4
DELIVERY VALVE
4
DELIVERY VALVE GASKET
4
DELIVERY VALVE HOLDER
4
LOCK PLATE ASSY.
2
TAPPET ASSY.
4
TAPPET GUIDE PIN
4
PLATE
2
PLUNGER SPRING
4
UPPER SPRING SEAT
4
LOWER SPRING SEAT
4
SHIM
4
CONTROL RACK
1
CONTROL SLEEVE
4
FOLLOW SCREW
1
GASKET
2
O RING
4
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 105
KUBOTA V2203 - ENGINE — FUEL CAMSHAFT ASSY.
FUEL CAMSHAFT ASSY.
PAGE 106 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — FUEL CAMSHAFT ASSY.
FUEL CAMSHAFT ASSY.
NO.
010
020*
030*
040*
050*
060*
070*
080*
090*
100*
110*
120*
140*#
150*#
160*
170*
180*
190
200
210
220
PART NO.
1666216020
1666216170
0815306205
1666251150
0571200525
0461200240
1981855450
1981855460
1981855510
1981855260
1666255270
1666255060
1982855280
1981855380
1666255620
1981855600
1981855340
0824000001
1522116320
0112360814
0461200250
PART NAME
QTY. REMARKS
FUEL CAMSHAFT ASSY. .............. 1 ....... INCLUDES ITEMS W/*
FUEL CAMSHAFT
1
BALL BEARING
1
INJECTION PUMP GEAR
1
FEATHER KEY
1
EXTERNAL CIR CLIP
1
GOVERNOR SLEEVE
1
THRUST WASHER
2
GOV. WEIGHT COLLAR
1
GOV. WEIGHT SHAFT
2
GOV. WEIGHT HOLDER
2
GOVERNOR COMP. WEIGHT ........ 2 ....... INCLUDES ITEMS W/#
GOVERNOR WEIGHT PIN
2
GOVERNOR BUSH
4
PLAIN WASHER
4
BEARING
2
WASHER
2
BALL BEARING
1
FUEL C/SHAFT STOPPER
1
BOLT
2
EXTERNAL CIR CLIP
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 107
KUBOTA V2203 - ENGINE — GOVERNOR ASSY.
GOVERNOR ASSY.
PAGE 108 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — GOVERNOR ASSY.
GOVERNOR ASSY.
NO.
010
020*
030*
040*
050*
060*
070*
080*
090
100
110
120
130
140
150
160
170
PART NO.
1718256050
1707656130
1981856150
0105350518
0451260050
1707656230
1522166410
0451260060
0112350832
0102350628
0401250080
0401250060
1981856480
1718256412
1718256420
1981855600
1981855340
PART NAME
QTY. REMARKS
FORK LEVER ASSY. ..................... 1 ....... INCLUDES ITEMS W/*
FORK LEVER
1
FORK LEVER SHAFT
1
BOLT
1
SPRING WASHER
1
FORK LEVER HOLDER
1
BOLT
1
SPRING WASHER
1
BOLT
2
BOLT
1
PLAIN WASHER
2
PLAIN WASHER
1
START SPRING
1
GOVERNOR SPRING
1
GOVERNOR SPRING
1
BEARING
2
WASHER
2
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 109
KUBOTA V2203 - ENGINE — SPEED CONTROL PLATE ASSY.
SPEED CONTROL PLATE ASSY.
PAGE 110 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — SPEED CONTROL PLATE ASSY.
SPEED CONTROL PLATE ASSY.
NO.
010
020
030
040
050
070
080
090
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
250
PART NO.
1981854120
1560192010
1560196650
1584114620
1622154420
1707657110
1707657740
1707656110
0481110160
0481110070
1362216670
1707957380
1707657162
3691927820
1584192010
1707657152
0541100318
1707657510
0501200412
1543957210
0102350620
1522188210
0451260060
0205650060
PART NAME
ADJUSTING BOLT
NUT
GASKET
CAP NUT
CAP
SPEED CONTROL PLATE
LEVER SHAFT
GOVERNOR LEVER
O RING
O RING
CAMSHAFT SHIM
COLLAR
CHANGE LEVER
PTO LEVER GRIP
SPEED CONTROL NUT
SPEED CONTROL LEVER
SPRING PIN
CHANGE SPRING
STRAIGHT PIN
GASKET
BOLT
STUD
SPRING WASHER
NUT
QTY.
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
2
2
REMARKS
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 111
KUBOTA V2203 - ENGINE — ENGINE STOP LEVER ASSY.
ENGINE STOP LEVER ASSY.
PAGE 112 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — ENGINE STOP LEVER ASSY.
ENGINE STOP LEVER ASSY.
NO.
010
020*
030*
040*
050*
060*
070
080#
090#
100#
110#
120#
130#
140
150
160
170
180
190
PART NO.
1707654093
1707654103
1540192010
1552192330
1502133660
1552154270
1748257702
1718351650
1733157740
1748257720
1547157980
0541100420
1748257920
1529651660
0102350618
0102350622
1718316210
3539437860
0115350865
PART NAME
QTY. REMARKS
IDLING APPARATUS ...................... 1 ....... INCLUDES ITEMS W/#
ADJUSTMENT BOLT ASSY.
1
NUT
1
CAP NUT
1
GASKET
2
CAP
1
ENGINE STOP LEVER ASSY. ....... 1 ....... INCLUDES ITEMS W/#
INJECTION PUMP COVER
1
LEVER SHAFT
1
ENGINE STOP LEVER
1
OIL SEAL
1
SPRING PIN
1
RETURN SPRING
1
PUMP COVER GASKET
1
BOLT
2
BOLT
2
FUEL CAMSHAFT COVER
1
GASKET
1
BOLT
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 113
KUBOTA V2203 - ENGINE — STOP SOLENOID ASSY.
STOP SOLENOID ASSY.
PAGE 114 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — STOP SOLENOID ASSY.
STOP SOLENOID ASSY.
NO.
010
020
030
040
050
060
070
080
PART NO.
1547160010
0112360816
0401250080
1733160150
1547160162
0401250060
0552550600
1718260110
PART NAME
STOP SOLENOID
BOLT
PLAIN WASHER
STOP LEVER
STOP LEVER
PLAIN WASHER
SNAP PIN
SOLENOID SUPPORT
QTY.
1
2
2
1
1
3
3
1
REMARKS
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 115
KUBOTA V2203 - ENGINE — ALTERNATOR ASSY.
ALTERNATOR ASSY.
PAGE 116 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 -EB ENGINE — ALTERNATOR ASSY.
ALTERNATOR ASSY.
NO.
010
020
030
040
050
060
070
080
090
100
110
120
130
140
PART NO.
1642764010
TA04074020
0117351000
0115360830
0451260080
0215650100
0451260100
0401150100
0401560080
0205650060
0451260060
1920274280
0571200720
1712397010
PART NAME
ALTERNATOR ASSY.
DYNAMO STAY
BOLT
BOLT
SPRING WASHER
NUT
SPRING WASHER
PLAIN WASHER
PLAIN WASHER
NUT
SPRING WASHER
FAN DRIVE PULLEY
FEATHER KEY
V - BELT
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
REMARKS
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 117
KUBOTA V2203 - ENGINE — ALTERNATOR (COMPONENTS) ASSY.
ALTERNATOR (COMPONENTS) ASSY.
PAGE 118 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — ALTERNATOR (COMPONENTS) ASSY.
ALTERNATOR (COMPONENTS) ASSY.
NO.
010
020*
030*
040*
050*
060*$
070*$
090*
100*#
110*#
120*#
130*#
140*
150*
160*
170*
180*
190*%
200*%
210*
220*
230*
240*
250*
260*
270*
280*
PART NO.
1642764010
1642764110
1588192010
1588164150
1588164040
1588164800
1588164770
1642764020
1588164710
1588193010
1588164260
1588164780
1624164060
1624164230
1623164850
1624164900
1588164310
1588164090
1588164330
1588193020
1588193030
1588193040
1588191040
1588192020
1588191050
1418292030
1588164600
PART NAME
QTY. REMARKS
ALTERNATOR ASSY. ..................... 1 ....... INCLUDES ITEMS W/*
ALTERNATOR PULLEY
1
NUT
1
COLLAR
1
ROTOR ........................................... 1 ....... INCLUDES ITEMS W/$
BEARING COVER
1
BALL BEARING
1
DRIVE END FRAME ...................... 1 ....... INCLUDES ITEMS W/#
RETAINER PLATE
1
ROUND HEAD SCREW
4
THROUGH BOLT
2
BALL BEARING
1
END FRAME
1
END COVER
1
RECTIFIER ASSY.
1
INSULATION BUSH
1
BRUSH HOLDER ............................ 1 ....... INCLUDES ITEMS W/%
BRUSH
2
BRUSH SPRING
2
ROUND HEAD SCREW
2
ROUND HEAD SCREW
6
ROUND HEAD SCREW
1
BOLT
3
NUT
2
BOLT
2
NUT
1
REGULATOR ASSY.
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 119
KUBOTA V2203 - ENGINE — FAN ASSY.
FAN ASSY.
PAGE 120 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — FAN ASSY.
FAN ASSY.
NO.
010
020
030
PART NO.
1737174110
1981874150
0175450625
PART NAME
FAN
FAN COLLAR
FLANGE BOLT
QTY.
1
1
4
REMARKS
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 121
KUBOTA V2203 ENGINE — WATER FLANGE AND THERMOSTAT ASSY.
WATER FLANGE AND THERMOSTAT ASSY.
PAGE 122 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — WATER FLANGE AND THERMOSTAT ASSY.
WATER FLANGE AND THERMOSTAT ASSY.
NO.
010
020#
030
040
050
060
070
080
090
100
110
120
130
140
150
160
PART NO.
1551272702
1733173342
1576672920
0112350822
0151350822
0115350870
0215650080
0451260080
1552173340
1510973360
1551296010
0471702150
1532173260
1531373270
0112350835
1943473010
PART NAME
QTY. REMARKS
WATER FLANGE COMP. ................ 1 ....... INCLUDES ITEMS W/#
WATER RETURN PIPE
1
WATER FLANGE GASKET
1
BOLT
2
STUD
1
BOLT
1
NUT
1
SPRING WASHER
2
WATER RETURN PIPE
1
PIPE BAND
2
PLUG
1
RUBBER WITH WASHER
1
THERMOSTAT COVER
1
GASKET
1
BOLT
2
THERMOSTAT ASSY.
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 123
KUBOTA V2203 - ENGINE — WATER PUMP ASSY.
WATER PUMP ASSY.
PAGE 124 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — WATER PUMP ASSY.
WATER PUMP ASSY.
NO.
010
020*
030*
040*
050*
060
070
080
090
100
110
120
PART NO.
1552173033
1552173550
1666173510
1666173050
1552173520
1576673430
0112350828
1552191510
0451260080
0215650080
0102350618
1736574250
PART NAME
QTY. REMARKS
WATER PUMP ASSY. .................... 1 ....... INCLUDES ITEMS W/#
BEARING
1
IMPELLER
1
MECHANICAL SEAL ASSY.
1
WATER PUMP FLANGE
1
WATER PUMP GASKET
1
BOLT
2
STUD
2
SPRING WASHER
2
NUT
2
BOLT
8
FAN PULLEY
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 125
KUBOTA V2203 - ENGINE — RADIATOR ASSY.
RADIATOR ASSY.
PAGE 126 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — RADIATOR ASSY.
RADIATOR ASSY.
NO.
010
020*
030*
040*
050
060
070
080
090
100
110
120*
PART NO.
1707972062
1560172330
1527272020
1707972710
1560172850
1542872940
1510872870
1546173340
1718273340
1540111720
1430142750
1907787240
PART NAME
QTY. REMARKS
RADIATOR ASSY. .......................... 1 ....... INCLUDES ITEMS W/#
FAN SHROUD
1
CAP ASSY.
1
WATER OVER FLOW PIPE
1
WATER PIPE
1
WATER PIPE
1
BAND
4
WATER RETURN PIPE
1
PIPE
1
PIPE BAND
2
PIPE CLIP
4
CAUTION LABEL
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 127
KUBOTA V2203 - ENGINE — FUEL FILTER ASSY.
FUEL FILTER ASSY.
PAGE 128 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
KUBOTA V2203 - ENGINE — FUEL FILTER ASSY.
FUEL FILTER ASSY.
NO.
010
030*
040*
050*
060*
070*
080*
090*
100*
110*#
120*
130*
140*
150*
PART NO.
1707643012
1552143522
1552143672
1552143552
1552143542
0481110290
1552193310
1552143150
1552143100
1687388430
1552143160
0481150650
1552143930
0481100160
PART NAME
QTY. REMARKS
FUEL FILTER ASSY. ...................... 1 ....... INCLUDES ITEMS W/*
FILTER HANDLE
1
GASKET
1
HANDLE RETAINER
1
THRUST PLATE
1
O RING
1
WASHER WITH SCREW
2
RETAINER RING
1
FILTER CUP ASSY.
1
FUEL LABEL .................................. 1 ....... INCLUDES ITEMS W/#
FILTER ELEMENT
1
O RING
1
SPRING
1
O RING
1
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 129
TERMS AND CONDITIONS OF SALE — PARTS
Effective: July 1, 2000
PAYMENT TERMS
4.
Terms of payment for parts are net 10 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and the
carrier.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
5.
Parts must be in new and resalable
condition, in the original Multiquip package
(if any), and with Muiltiquip part numbers
clearly marked.
6.
The following items are not returnable:
a.
Obsolete parts. (If an item is listed
in the parts price book as being
replaced by another item, it is
obsolete.)
b.
Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
MINIMUM ORDER
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c.
Any line item with an extended dealer
net price of less than $5.00.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a specific
date and all orders received on or after that date
will be billed at the revised price. Rebates for
price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.
Multiquip reserves the right to quote and sell
direct to Government agencies, and to Original
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
SPECIAL EXPEDITING SERVICE
A $20.00 to $50.00 surcharge will be added to
the invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
d.
Special order items.
RETURNED GOODS POLICY
e.
Electrical components.
Return shipments will be accepted and credit
will be allowed, subject to the following
provisions:
f.
Paint, chemicals, and lubricants.
LIMITATIONS OF SELLER’S LIABILITY
g.
Decals and paper products.
1.
h.
Items purchased in kits.
Multiquip shall not be liable here under for
damages in excess of the purchase price of the
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
2.
A Returned Material Authorization must
be approved by Multiquip prior to shipment.
To obtain a Return Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
a.
b.
The list must be typed or computer
generated.
c.
The list must state the reason(s) for
the return.
d.
The list must reference the sales
order(s) or invoice(s) under which
the items were originally purchased.
e.
3.
The parts numbers and descriptions
must match the current parts price
list.
The list must include the name and
phone number of the person
requesting the RMA.
A copy of the Return Material
Authorization must accompany the return
shipment.
7.
The sender will be notified of any material
received that is not acceptable.
8.
Such material will be held for 5 working
days from notification, pending
instructions. If a reply is not received
within 5 days, the material will be returned
to the sender at his expense.
9.
Credit on returned parts will be issued at
dealer net price at time of the original
purchase, less a 15% restocking charge.
10. In cases where an item is accepted for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
11. Credit issued will be applied to future
purchases only.
LIMITATION OF WARRANTIES
No warranties, express or implied, are made
in connection with the sale of parts or trade
accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes not
authorizes any person to assume for it any
other obligation or liability whatever in
connection with the sale of its products. A part
from such written statement of warranty, there
are no warranties, express, implied or statutory,
which extend beyond the description of the
products on the face hereof.
PAGE 130 — DCA-15SPX3 GENERATOR— PARTS & OPERATION MANUAL — REV. #2 (09/03/01)
NOTE PAGE
DCA-15SPX3 GENERATOR — PARTS & OPERATION MANUAL — REV. #2 (09/03/01) — PAGE 131
PARTS AND OPERATION MANUAL
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PAR
TS DEP
AR
TMENT
ARTS
DEPAR
ARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
VICE DEP
AR
TMENT
SER
ARTMENT
SERVICE
DEPAR
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEP
AR
TMENT
DEPAR
ARTMENT
800/835-2551, or 310/537-3700
FAX: 310/698-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
Manufactured for Multiquip Inc.
by
DENYO MANUFACTURING CO., USA
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX: 310-537-3927
E-MAIL: [email protected]
WWW: multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement