Medema | Mini Crosser M2 | User manual | Medema Mini Crosser M2 User manual

User Manual
Mini Crosser M2
medemagroup
P9-0157-B ver. 2.0.3 - July 2012
GB
Medema Production A/S
Serial number: ___-______________-______-_______
Delivery date: ________________ Year 20______
This vehicle was supplied by:
User guide P9-0157-B
Date:
2 of 56
/
Version 2.0.3/2012
Medema Production A/S
Contents
Symbols.................................................................................. 4
Warning! ................................................................................. 4
Alarm ...................................................................................... 4
Contagion!.............................................................................. 4
Introduction............................................................................ 5
Declaration of conformity ..................................................... 6
Control panel ......................................................................... 7
User menu .............................................................................. 8
Programming the User Menu ............................................... 11
Preparations / Adjustments prior to use ............................. 13
Electric seat adjustment ....................................................... 14
Seat rotation........................................................................... 15
Steering column .................................................................... 16
Serial number......................................................................... 17
Driving the Mini Crosser M2 ................................................. 18
Specific driving situations .................................................... 23
Long hills/difficult ground .................................................... 25
Anti-tilt wheels / stabilisers .................................................. 26
General care and maintenance ............................................ 27
Insurance................................................................................ 28
Batteries ................................................................................. 29
Charging ................................................................................. 29
Battery disposal..................................................................... 31
Storage ................................................................................... 31
Cleaning ................................................................................. 31
Changing the wheels............................................................. 32
Fuses ...................................................................................... 34
Brakes..................................................................................... 35
Disengagement ...................................................................... 35
Transporting by motor vehicle ............................................. 36
Securing to vehicle floor with belts ..................................... 37
Transporting by plane ........................................................... 40
Towing .................................................................................... 40
Dimensioned drawing, Mini Crosser M2 3W ........................ 41
Dimensioned drawing, Mini Crosser M2 4W ........................ 42
Introduction to seats - Ergo Standard ................................. 43
Introduction to seats - Mando .............................................. 45
Troubleshooting .................................................................... 46
Programming ......................................................................... 49
Technical data ........................................................................ 50
Own notes .............................................................................. 53
International addresses ........................................................ 54
User guide P9-0157-B
3 of 56
Version 2.0.3/2012
Medema Production A/S
Symbols
Used in the manual to indicate sections describing situations
where extra care is required owing to the risk of personal injury.
Used to indicate sections on electromagnetic compatibility
(EMC).
Warning!
For safety reasons the vehicle must not be lent to persons who
are not completely familiar with it. The vehicle is designed for
one person only.
The Mini Crosser M2 has been designed for users weighing
max. 175 kg. Can be supplied in a HD version as standard for a
max person weight of 250 kg.
Alarm
Temperature sensor, alarm system and tilt alarm are built into
the same box that can be acquired as an option for the Mini
Crosser M2.
Note!
The alarm is always turned off on delivery. See the chapter
about ”Programming the User Menu” to turn on the alarm.
Contagion!
Note!
The tires can sometimes rub off on floor coverings, particularly
linoleum. Medema Production assumes no responsibility in
case of contagion.
To prevent this, we recommend that you protect delicate floors
with some sort of driving surface.
User guide P9-0157-B
4 of 56
Version 2.0.3/2012
Medema Production A/S
Introduction
Congratulations on your new Mini Crosser M2 electric mobility
scooter.
You have now taken possession of an electric mobility scooter
developed for outdoor driving by active users. It is what is
called a Class C vehicle in accordance with the European
classification of electric scooters.
For optimum enjoyment of this vehicle - and to avoid
breakdowns and accidents - we recommend that you read this
User Manual carefully. As a new user, you should pay particular
attention to the section entitled “Driving the Mini Crosser M2”.
The Mini Crosser M2 is designed for safe travel for at least
10 years, up to a max. of 5,000 hours, provided it is serviced
and safety-checked every year, corresponding to 500 hours of
operation. The service must be carried out by an authorised
workshop.
IMPORTANT! For safety reasons it is of the utmost importance
that service and safety check intervals are complied with, as
this minimises the risk of brake failure and short-circuits in the
wiring, which could generate heat and cause a fire.
We offer a wide range of accessories for the Mini Crosser M2
that can make everyday life easier for you. You are always
welcome to contact us for further information on special
accessories and adaptations.
Mini Crosser A/S is not responsible for any damage or injuries
caused by inappropriate or unsafe use of the Mini Crosser M2.
If you have any further questions about the Mini Crosser M2 or
this User Manual, you are always welcome to get in touch. Our
contact details are as follows:
Medema Production A/S
Tel: +45 7010 2054
Email: info@minicrosser.com
Internet: www.medema.com
NB: Errors and omissions excepted. We reserve the right to
update this manual as required.
User guide P9-0157-B
5 of 56
Version 2.0.3/2012
Medema Production A/S
Declaration of conformity
Medema Production A/S hereby declares that:
Machine:
Mini Crosser
Use:
(Prescribed use in
User Manual)
Model No:
M2
Complies with the Medical Device Directive 93/42/EEC
The product is made in accordance with the harmonized
standard EN 12184 - Electrically powered wheelchairs, scooters
and their chargers.
The product is risk analysed in accordance with the harmonized
standard DS/EN ISO 14971:2007-04-10 2. edition - Medical
devices - Application of risk management to medical devices.
The Mini Crosser can, for a fee, be taken to the nearest
dealer for disposal in accordance with current environmental
regulations.
User guide P9-0157-B
Manufacturer:
Medema Production A/S
Address:
Enggårdvej 7, DK-7400 Herning
Tel./Fax
+45 7010 2054 +45 9716 8582
Date: 12.04.2010
Signature: _____________________
6 of 56
Version 2.0.3/2012
Medema Production A/S
Control panel
Avoid subjecting the control panel to jarring and knocks. Take
care when driving and avoid hitting obstacles.
The manufacturer accepts no liability in respect of the
unauthorised opening, adjustment or modification of the control
panel.
Menu / information
Actual speed
Mileage
Battery indicator
Hazard warning lights
Light sensor
Speed selector
Light switch
Handbrake
Indicator lights, R/L
Accelerator
(four-finger control)
anti-theft alarm
Indicator lights,
R/L
Horn
Extra Switch
Can be used
for optional
functions.
Speed
regulation
Trip meter
Horn
Lever for adjusting the angle of the handlebars
Charging socket
Key switch
Accelerator
(four-finger control)
User guide P9-0157-B
7 of 56
Version 2.0.3/2012
Medema Production A/S
User menu
User guide P9-0157-B
Term
Description
Menu / information
Press the button and a menu at the top of the display
switches between ”Date”, ”Time”, ”Complete km”,
”Complete running time”, ”Battery Voltage” Service
”and” inclination ”.”Slope” is optional, and appears
only if it is engaged.
Button Menu / information are also used to modify the
user parameters.
Access these parameters by holding the menu button
for approx. 3 sec.
Key switch
To start the vehicle:
Turn the key to position (1). The first half second after
the Mini Crosser is on, the control is making a safety
check of the electrical system. If the accelerator is
affected during this time, the Mini Crosser will not be
able to run, before the key again has been turned at 0
and back to 1 again.
Speed selector
The turtle indicates lowest speed range. 0-6 km / h.
The hare indicates the highest speed range. Up to 15
km / h. Increase/decrease with + / - button.
The icons turtle/hare can be turned on/off from the
User menu.
Battery indicator
The left side of the display shows battery level indicator.
Indicates that after approx. ½ seconds, the battery state of
charge. Provides a more accurate indication after approx. 1
minute drive. When both red, yellow and green box lights
are the batteries fully charged. Can be divided into 10 or
3 boxes. When the view is down the bottom of the yellow
batteries should be recharged as soon as possible. If there
is only light in the red boxes or flashing the batteries must
be charged immediately.
Trip meter
TRIP button resets the trip meter. Can be used while
driving.
Hand brake
Works on the left rear wheel and should only be used
as extra brake / emergency brake and parking brake.
It can be blocked in the locked position. Also available
as a foot brake.
8 of 56
Version 2.0.3/2012
Medema Production A/S
Term
Description
Accelerator
Front arm activates slowly and the Mini Crosser will
start running forward. The more press, the faster it will
run. When the lever is released, the arm flips itself back
to the starting position and Mini Crosser stops.
Upon activation of the posterior arm, the Mini Crosser
run backward. The Magnetic brake on the rear wheels
will strike at standstill, corresponding to the parking
brake on a car. With speed regulation, speed can also
be regulated downhill. The engine will then act as a brake.
Forw. / Backw.
User guide P9-0157-B
Light switch
Turns on the front and rear lights. The key switch must
however be turned to position 1 (drive).
Hazard warning lights
Turns on all lamps at once. Also works when the key
is removed, or turned to 0 (stop position).
Indicator lights switch
Arrow left: lamp left side. Arrow Right: lamp right side.
Activate the same button again to turn off flashing
lights.
Horn
Electric horn which can be programmed in volume in
the User Menu. Activated by pressing the horn button.
Charging socket
Turn off the Mini Crosser (key in position 0) during
charging. Note that it is not possible to run while the
batteries recharge. See also the section ”Batteries
and Charging.”
9 of 56
Version 2.0.3/2012
Medema Production A/S
Term
Description
Extras
User guide P9-0157-B
Anti-theft alarm
(Extra) With this parameter set to ON, the anti-theft
alarm is turned on every time you turn off the Mini
Crosser. An activated alarm is turned off by turning the
key to 1 (drive).
If you have no opportunity to get to the Mini Crosser
with the key, the alarm will stop after approx. 20
seconds. Shake the scooter again, the alarm will be
activated again.
Tilt
Tilt-symbols.
Tilt Alarm sideways
By exceeding the preset value, the symbol flashes and
the horn hoots, if the parameter is enabled.
Tilt Alarm forw./backw.
By exceeding the preset value, the symbol illuminate
and the horn hoots, if the parameter is enabled.
Overheating step 1
Step 1: The symbol flashes and the speed is reduced to
half power. Wait for 3-5 min and start again.
Overheating step 2
Step 2: The symbol will illuminate and Mini Crosser
stops. Wait 3-5 minutes and start again.
10 of 56
Version 2.0.3/2012
Medema Production A/S
Programming the User Menu
Access the menu by holding the Menu/information button for approx.
3 sec. Scroll up and down with the + / -button under the display.
The active parameter is highlighted with yellow writing and blue
background. Access the value of the selected parameter by pressing
Enter. Change the value using the +/- button. Confirm with Enter and
exit with the Menu/information button.
Parameter description
Date Format
Choose between:
ddmmyy - day/month/year
mmddyy - month/day/year
yymmdd - year/month/day
Temp. unit
(Temp. unit is extra)
Choose between Celsius or Fahrenheit. Displays ambient
temperature.
Limited speed
(On/Off)
Limited speed On/Off.
To edit this function you will be asked for a 4 digit code.
From the factory this code is set to be 1234, but it can be
altered by a service technician.
Use the +/- button to each digit. Go to the next digit with
the “Next” button. Confirm with “Enter” Turn this parameter
On/Off – Confirm with “Enter”.
Limited speed (value) Limited speed - value.
To edit this function you will be asked for a 4 digit code.
From the factory this code is set to be 1234, but it can be
altered by a service technician. Use the +/- button to set %
value, that you want the scooteres max speed reduced to.
Move in increments of 5%.
User guide P9-0157-B
Backlight (value)
The displays backlight can be changed in increments of
5%. Typically used in winter or when driving in darkness,
where the intense light from the display may seem
annoying.
Backlight auto
(On/Off)
Selecting ”On” reduced intensity of the backlight
automatically when darkness falls or when driving into
a tunnel or similar. Light sensor sits just above the light
switch. See the Control panel.
Backlight threshold
Here max. light intensity is shown in%. Move in increments
of 5%.
Reverse Buzzer (Off/
Beep/Buzze)
Same warning horn as it is known from trucks in reverse
gear.
Choose from ”Off”, ”Beep” - low horns, or ”Buzzer” - sharp
horns.
Keyboard sound
(On/Off)
With ON / OFF select whether to be acknowledged with a
little beep when you press the contacts on the dashboard.
These are: flashing, lights, hazard, menu, arrows and
MENU keys.
Blinker sound (Off/
Beep/Buzze)
Choose whether you want a sound when flashing lights on
the scooter is on. Just as we know it from a car. You can
select ”Off”, ”Beep” - low horns, or ”Buzzer” - sharp horns.
11 of 56
Version 2.0.3/2012
Medema Production A/S
Parameter description
Clock
Set time and date using the up / down with arrows. Moving
to the next digit by pressing the ”next” button. Quit with the
”Enter”
Hazard enabled
(On/Off)
By default hazard (emergency lights) is operable even if the
scooter is switched off and the key is removed.
If you wish the hazard not be activated with the scooter
turned off, you should select ”Off.” here.
Alarm enabled
(On/Off) Extra
With this switch ”On”, the burglar alarm is turned on every
time you turn off the scooter. The small lamp next to the
”Trip meter” will fl ash a few seconds interval.
An activated alarm is turned off by switching the key on the
scooter. If you have no opportunity to get to the scooter
with the key, the alarm will switch off after approx. 20th
seconds. Shake / move the scooter again, the alarm will be
activated again.
Tilt Present (On/Off)
Extra
With this parameter set to ”On”, will turn the tilt icons to red
and blinking, and there will be a whining tone (if enabled) if
you are running on a slope that is steeper than allowed.
P&G fault log
Here are the faults that P & G engine management has
registered. The system can record 8 different types of
faults. Each fault can be recorded up to 30 times.
The newest registered fault is written at the top of the list.
They are shown as follows:
[1502] 2
None
None
None
None
None
None
In this case, the fault 1502 appeared twice. If you press
ENTER on the fault you will get an explanatory text. In this
case, ”Solenoid brake fault”
None means that there have not been other faults.
In case of fault on the scooter, it will be a great help if
the fault type can be given to the Mini Crosser or his
representative during troubleshooting.
Temperature sensor, alarm system and tilt alarm are built into
the same box that can be acquired as an option for the Mini
Crosser M2.
User guide P9-0157-B
12 of 56
Version 2.0.3/2012
Medema Production A/S
Preparations / Adjustments prior to use
Adjusting the height of the seat
Lift the seat off and remove the rear cover. Press the release
button out and adjust the seat tube to the desired position.
See the picture on the next page. Check that the seat height
is correct and press the release button in again. Move the seat
tube up/down until the release clicks into a hole.
Make sure you keep your back straight when lifting the seat,
which is very heavy. (See below.)
Lift the seat off the seat tube.
The release button pressed in. Press the
button out to release the seat tube.
User guide P9-0157-B
13 of 56
Release button pressed out. Now the
seat tube can be moved up/down to
the height you wish. Press the release
button again and make sure it is fitted in
one of the 5 holes in the seat tube.
Version 2.0.3/2012
Medema Production A/S
Seat tube
Release
Seat tube in top position. There are five
holes for adjusting the seat tube. The
release must be in a hole for the seat to
be stable.
Electric seat adjustment
The Mini Crosser can be fitted with electric seat adjustment as
an optional extra.
To raise the seat, press the switch up. To lower the seat, press
the switch down. If the switch is released, the seat will stop
automatically. (See figure below.)
Switch for electric
seat adjustment
Electric seat adjustment. If the switch is pressed up, the seat
is raised. If the switch is pressed down, the seat is lowered.
User guide P9-0157-B
14 of 56
Version 2.0.3/2012
Medema Production A/S
Seat rotation
Pull the release lever back. The seat can be rotated 90° to
either side. When the lever is released, it engages with the seat
and holds it in place at 45° intervals.
Other seats that can be supplied for the Mini Crosser work on
similar principles. The release lever is normally mounted on the
right, but can be put on the left if so wished.
IMPORTANT!
The Mini Crosser is most stable when the seat is in its lowest
position. Always drive carefully when the seat is raised. Never
use the seat adjustment when driving on an uneven surface or
in hilly terrain.
Take extra care when lowering the seat on a Mini Crosser using
electric seat adjustment. Make sure that nothing is trapped in
the space between the seat and the chassis.
Avoid trapping anything when lowering the seat.
Release lever for seat rotation. Release lever for seat forward/back.
User guide P9-0157-B
15 of 56
Version 2.0.3/2012
Medema Production A/S
Steering column
Can be adjusted forward/back with the release lever. Pull down
on the lever and pull the handlebars closer for a good driving
position. Use the lever again and push the steering column
forward to make it easier to get out.
The height of the steering column can be adjusted approx. 11
cm up/down. First remove the rubber plug covering the Allen
screw. Adjust the height using a 4 mm Allen key.
This applies to both the 3W and the 4W model. Remember to
retighten properly after adjusting.
Adjusting the height of
the handlebars. Applies
to both the 3W and the
4W model.
Lever for adjusting the angle of
the handlebars
Adjusting the height of
the handlebars. Applies
to both the 3W and the
4W model.
Allen screw for height
adjustment
User guide P9-0157-B
16 of 56
Version 2.0.3/2012
Medema Production A/S
Serial number
All vehicles have a serial number plate showing the year of
production and serial number. The same serial number can also
be found on the front of the User Manual.
Please quote this number when making inquiries about
servicing, spare parts, etc.
Maximum user weight
Model description
Vehicle’s unladen weight inc.
batteries and seat
Serial number
Year of production
Max. speed
Position of serial number plate on vehicle.
User guide P9-0157-B
17 of 56
Version 2.0.3/2012
Medema Production A/S
Driving the Mini Crosser M2
Getting in and out
It is important to learn a safe technique for getting in and out of
the Mini Crosser.
In general the following method should be followed:
•
•
•
•
•
Make sure that the Mini Crosser M2 is off (switch turned to 0)
when getting in and out, otherwise the Mini Crosser could start if
the accelerator was touched inadvertently.
Make sure that the brake is on. (Lever for disengaging motor in
top position.)
Put the steering column in vertical position.
If necessary, turn the seat through 45° or 90° and make sure that
it is locked in position (clicked into place).
If necessary, raise the armrest.
For some users the assistance of an attendant can be recommended.
The attendant should:
•
•
•
Take care not to injure him/herself when lifting/lowering/supporting
the user.
Make sure that the Mini Crosser is stable and unable to move.
Turn off the Mini Crosser and check that the brake is on and the
seat has been rotated until it clicks into place at either 45° or 90°.
Make sure that the seat the user is being moved to is stable.
IMPORTANT!
The Mini Crosser will turn itself
off automatically after it has
been stationary for 10 minutes
even if the key has been
turned to driving position.
To restart the vehicle, the
key must be turned to stop
position (0) and then to driving
position (1).
Turn the Mini Crosser off, return the
steering column to upright position, rotate
the seat and raise the armrest.
User guide P9-0157-B
18 of 56
Version 2.0.3/2012
Medema Production A/S
Braking systems
There are three braking systems on the Mini Crosser:
•
Motor brake - adjusts vehicle speed also when going downhill.
•
Magnetic brake - the magnetic brake is automatic and
engages when the Mini Crosser stops. In an emergency,
the Mini Crosser can be stopped instantaneously by turning
the key switch. Please note that this will cause very sharp
braking.The brake must never be disengaged mechanically
using the disengagement lever on a slope. This function is
only designed for use when pushing the Mini Crosser on a
flat road.
•
Electric safety brake - if the brake is somehow disengaged on
a slope/hill, the Mini Crosser will brake automatically when it
reaches a certain speed. There is an electric safety feature in the
control system, which works even if the battery is disconnected.
This is also the reason why the Mini Crosser cannot be towed at
more than 5 km/h. See the section about towing.
•
Handbrake - intended as an emergency brake and parking
brake. It must be operated with caution when driving in
slippery conditions and downhill.
When using the handbrake as a parking
brake, lock it in braking position by
pressing the button in while applying the
brake.
To release the brake, press the button
again.
Handbrake lock
General safety advice
Make sure that the backrest is upright and the seat is as low as
possible.
Positioning belts are recommended if the user is unable to
maintain a good driving posture independently.
Adjust your driving to road conditions. Take account of light,
traffic and weather. Be particularly careful when driving in the
User guide P9-0157-B
19 of 56
Version 2.0.3/2012
Medema Production A/S
dark or in bad weather, such as rain or snow. Avoid driving on
gradients with poor surfaces, such as: snow, ice, new-mown
grass, wet grass and wet leaves.
Never drive when under the influence. This applies not only to
alcohol, but also to drugs and medicines.
Reduce speed immediately if you feel you are losing control.
Always use the indicators when changing direction.
Check that lights and indicators are working before driving off.
Use your lights when driving after lighting-up time.
As far as possible, grip the handlebars firmly with both hands.
Take care not to have anything in the basket at the front that
might inadvertently operate the accelerator.
WARNING! Do not lower the handlebars so far that the
accelerator can hit you on the leg when you turn the vehicle and
so be operated in advertently. If the handlebars need to be very
low, a twist grip accelerator is recommended. This is particularly
relevant if leg supports are being used.
ALWAYS switch the scooter off when it is not in use. Turn the
key to 0.
Driving
Even though the Mini Crosser is very stable, it can tip over.
Avoid sudden changes of speed and direction when travelling at
high speed, on poor surfaces and, not least, on slopes.
For short distances the Mini Crosser can drive up steeper
gradients than it has been tested as dynamically stable for. The
same applies to driving down such gradients. In such cases
there is an increased risk of the Mini Crosser tilting and even
tipping over. So be extra careful in following the driving tips
given below.
Anti-tilt wheels are recommended for driving in very hilly terrain.
(Optional extra)
User guide P9-0157-B
20 of 56
Version 2.0.3/2012
Medema Production A/S
New users are urged to practise the following in an area where
there is no other traffic:
•
Set the Mini Crosser to low speed. Drive forwards and backwards.
Gradually turn the speed selector up and feel the change in the
speed of the Mini Crosser.
•
Practise starting and braking. Get used to the Mini Crosser’s
response time.
•
Practise driving in a narrow space, similar to inside a shop or
through a door.
•
Practise turning, and get a sense of how much space is required.
Always drive slowly when turning. Practise reversing too.
•
Practise cornering and driving over obstacles and on slopes.
Always drive straight up/down kerbs and ramps. Never at an
angle. See the illustrations on the following pages.
•
Try braking at different speeds and notice the stopping distances.
•
If possible, try driving on different surfaces (road, grass and
gravel).
•
Practise assessing how far you can drive on a single battery
charge. Note how quickly the battery indicator changes from
green to amber to red.
Note!
The driving distance of the scooter will be reduced when driving
in hilly districts, into a head wind, in cold weather and with low
tyre pressure.
Traffic regulations
The traffic legislation for scooters varies from country to
country. Before starting to use the vehicle outdoors, it is the
user’s responsibility to familiarise him/herself with the relevant
legislation.
The following rules apply in Denmark:
Mobility vehicles such as the Mini Crosser with a maximum
speed of up to 15 km/h count as cycles in traffic legislation and
the traffic regulations for cycles must be followed at speeds in
excess of 6 km/h.
User guide P9-0157-B
21 of 56
Version 2.0.3/2012
Medema Production A/S
At speeds of up to 6 km/h the Mini Crosser is regarded as a
“pedestrian”, and it is permissible to travel on the pavement at
this speed. “Tortoise” speed corresponds to approx. 6 km/h.
Lights must only be used during lighting-up time. Crash helmet
and seat belts are not compulsory.
Electromagnetic compatibility
If the Mini Crosser starts making involuntary movements or if
the brakes are released, turn the Mini Crosser off as soon as it
is safe to do so. In certain circumstances a Mini Crosser can set
off shop alarms.
The Mini Crosser satisfies the requirements for the use of
scooters in an environment with electromagnetic noise. There
may, however, be rare situations in which electromagnetic noise
can affect the Mini Crosser. Sources of such noise include radio
and television stations, amateur radio transmitters and mobile
phones.
If such equipment is being used close by, it is recommended
that the Mini Crosser is switched off. Mobile phones should not
be used while driving.
When driving in traffic...
Be particularly aware of the following when driving in traffic:
User guide P9-0157-B
•
The Mini Crosser is a low vehicle and not always easy for other
road users to see. Make quite sure that other road users have
seen you before driving onto the highway.
•
Keep an eye on traffic behind you. Keep well over to the side of
the road when driving on busy roads.
•
Turning right and left at crossroads. Be aware of cyclists and
pedestrians. Follow the rules of the road for cyclists.
•
How quickly things are happening. How long do the lights stay
green? How quickly are cars approaching? etc.
22 of 56
Version 2.0.3/2012
Medema Production A/S
Specific driving situations
Up kerbs
•
•
•
•
Stop at right angles to the kerbstone about 5-10 cm away from it.
Keep an eye on other road users.
Lean forwards.
Accelerate moderately so that your vehicle can overcome the
obstacle. Do not stop halfway, but reduce speed once the vehicle
is up.
If the kerb is too high, do not try again, but find an alternative
route.
Down kerbs
•
•
•
User guide P9-0157-B
Lean back.
If you are driving onto a road with traffic, keep an eye on other
road users.
Drive forwards and down the kerb at low speed. Make sure that
your anti-tilt wheels (if fitted) do not catch on the edge.
23 of 56
Version 2.0.3/2012
Medema Production A/S
Up a ramp/hill
•
•
•
•
There is a risk of tipping over backwards if the seat is pushed
back when you start driving up a slope, e.g. a ramp.
Pull the seat forward! Check that any ramp is stable.
Lean forwards.
Accelerate moderately so that your vehicle can overcome the
obstacle. Do not stop halfway. Reduce speed once the vehicle is
up. If you need to start on a hill, accelerate slowly so as not to tip
over backwards.
Down a ramp/hill
•
•
•
User guide P9-0157-B
Check that any ramp is stable.
Lean back.
Drive slowly down. Avoid stopping midway on short, steep slopes.
On long hills, it is advisable to stop every now and again if you
feel your speed is getting too high.
24 of 56
Version 2.0.3/2012
Medema Production A/S
Across a slope
•
•
•
Lean into the slope.
Avoid sudden and sharp movements. This is particularly relevant
when reversing.
Always drive at low speed.
Long hills/difficult ground
The Mini Crosser is at risk of overheating on very long and
steep hills or on very soft ground, possibly also combined with
high user weight.
To protect the Mini Crosser motor from overheating, there is a
built-in thermo switch, which initially sets the Mini Crosser to
half speed.
However, if you carry on moving over difficult ground, the Mini
Crosser will at some stage stop completely, and the battery
indicator will flash with 6 lamps. The Mini Crosser must be left
to cool down for 3-5 minutes before it can start again.
To reset the fault, switch off the Mini Crosser then turn it on
again.
If the Mini Crosser has not had long enough to cool down when
it is restarted, it will initially only run at half speed.
Note:
The situation described above will never happen in normal use.
It only happens if the conditions are extremely challenging.
User guide P9-0157-B
25 of 56
Version 2.0.3/2012
Medema Production A/S
Anti-tilt wheels / stabilisers
The Mini Crosser is a very stable vehicle. HOWEVER, in the
case of incorrect weight distribution or careless driving there is
a risk of tipping over.
We therefore recommend fitting anti-tilt wheels in such
circumstances. (See picture below)
(Anti-tilt wheels / stabilisers are optional extras.)
Anti-tilt wheels
User guide P9-0157-B
26 of 56
Version 2.0.3/2012
Medema Production A/S
General care and maintenance
A Mini Crosser M2 does not require much maintenance. It
should be kept in a generally good condition, however. The
following should be checked regularly:
•
•
•
•
Tyre pressure (if pneumatic tyres are fitted)
Tyre wear
Keep the control panel, the charging socket and the electronics
box under the seat dry.
Battery charging
Never wash the Mini Crosser with a high-pressure cleaner
or direct water jet! This could damage the Mini Crosser’s
electronics.
To keep the Mini Crosser in good condition safety-wise, we
recommend the following regular checks:
Daily:
•
Test the indicators and driving lights before using the Mini Crosser
in the dark or poor visibility.
Every three months:
Test the brakes and motor disengagement
With the disengagement lever up, it must not be possible to
push the Mini Crosser.
Test the brake disengagement function
When the brake disengagement lever is down, the battery
indicator should flash to show an error if the Mini Crosser is
turned on. In this case the Mini Crosser must not be able to
move when the accelerator is activated.
Test the handbrake.
Apply the handbrake for a couple of seconds at low speed. This
will ensure that the lever arm and brake shoes do not seize up.
Lubricate the lever arm on the brake hub with acid-free oil - lefthand rear wheel.
User guide P9-0157-B
27 of 56
Version 2.0.3/2012
Medema Production A/S
Annual
The Mini Crosser M2 is designed for safe travel for at least
10 years, up to a max. of 5,000 hours, provided it is serviced
and safety-checked every year, corresponding to 500 hours of
operation. The service must be carried out by an authorised
workshop.
IMPORTANT! For safety reasons it is of the utmost importance
that the servicing and safety check intervals are complied with,
as this minimises the risk of brake failure and short-circuits in
the wiring, which could generate heat and cause a fire.
(For further information see the Service Manual.)
Insurance
In the eyes of the law a Mini Crosser M2 with a maximum speed
of 15 km/h is a cycle, so separate insurance is not required.
Most contents/home insurance policies include third-party
liability insurance for cyclists and so also cover Mini Crosser M2
users.
We recommend that you talk to your insurance company about
this when the vehicle is delivered.
If necessary, comprehensive insurance will have to be taken out
separately.
User guide P9-0157-B
28 of 56
Version 2.0.3/2012
Medema Production A/S
Batteries
The Mini Crosser uses sealed, maintenance-free GEL batteries
(Exide 12 V/56 Ah or AGM 12 V/71 Ah).
They do not generate gas and do not have to be topped up with
water.
Charging
Please NOTE that the Mini Crosser can be equipped with
several types of charger (ask your dealer for information on the
various types).
IMPORTANT! Only ever use a charger designed for charging
dry maintenance-free batteries. The max. charging current is
12 A.
If charging is to take place outdoors, an enclosed charger
without a fan should be chosen.
The battery manufacturer recommends charging the batteries at
temperatures between +10° and +30°C in order to achieve the
charging times specified in “Technical data”.
Charging will take longer at temperatures below +20°C. This is
because the battery finds it more difficult chemically to absorb
the current.
Please NOTE that the capacity of the batteries will reduce
over time and at low temperatures. In practice this means that
vehicles with old batteries have a shorter driving distance than
they had when the batteries were new.
Battery capacity at -10°C is about half the equivalent capacity at
+20°C.
Note!
The Mini Crosser uses a little power even when it is turned
of and the key is turned to 0. It is therefore recommended to
connect it to the charger whenever it is not used.
User guide P9-0157-B
29 of 56
Version 2.0.3/2012
Medema Production A/S
Avoid draining the batteries completely. We recommend charging
the batteries in a heated room. If it is not possible to do this every
day, it is a good idea to charge the Mini Crosser in a heated room
(approx. 20°C) once a week.
New batteries do not reach full capacity until they have been
charged and discharged about 20 times.
It is IMPORTANT to fit the batteries correctly. The battery terminals
and snap locks are marked +/-. They must be fitted as shown in the
sketch below. Make sure that the snap locks are properly closed.
For the same reason there must not be any burrs on the terminals.
The Mini Crosser should be charged while not in use. The
charger supplied from the factory switches over to trickle
charging (very low power consumption) automatically when the
batteries are fully charged. You can therefore leave the charger
connected until the Mini Crosser is next used. The charger
cannot overcharge the batteries.
The charger will flash until charging is complete. Then it will
show a steady light.
The charger must not be placed on the seat during charging.
IMPORTANT! Never use charging devices other than those
supplied from the factory without first contacting the dealer.
NEUTRIK NC3MX charging plug
User guide P9-0157-B
30 of 56
Connect the charging plug to the 3-pin
socket on the steering column. The
charging socket is located under the
protective cover.
Version 2.0.3/2012
Medema Production A/S
Battery disposal
Used batteries must be disposed of through your supplier or at
a recycling centre.
Take care when handling leaky batteries, as the gel contains
corrosive acid.
INFO!
New batteries can be purchased from Medema Danmark A/S.
Storage
The scooter should be stored and charged under cover,
preferably at temperatures above 0°C.
Note!
The charger must be kept dry, but should not be covered when
in use.
In the case of long-term storage we recommend covering the
Mini Crosser M to protect it from dust, rain and sunlight.
Cleaning
Clean the Mini Crosser M2 with a damp cloth. If necessary, wipe
dry with a chamois leather.
Wipe the covers dry and polish with car wax.
IMPORTANT! Never use a high-pressure cleaner or hose, as it
could damage the Mini Crosser’s electronics.
User guide P9-0157-B
31 of 56
Version 2.0.3/2012
Medema Production A/S
Changing the wheels
If you get a puncture in one of the pneumatic tyres or if a
tyre is so badly worn that it needs to be replaced, follow the
instructions below.
Tyres and inner tubes can be purchased from the authorised
dealer who supplied the Mini Crosser.
The Mini Crosser must be TURNED OFF before you start.
Changing the wheels on
the 4W model
5 mm Allen key
•
•
•
REMEMBER!
•
•
User guide P9-0157-B
to let all the air out before taking
the wheel apart to repair a
puncture
to secure the bolts with spring
washers
32 of 56
Undo the five bolts.
Take the wheel off.
When the wheel is put
back on, the spring
washers must be refitted
between the wheel rim
and bolts.
The bolts must be done
up tightly.
Version 2.0.3/2012
Medema Production A/S
Changing the wheels on
the 3W model
Rear wheels: Take off
in the same way as
described above.
Front wheel:
17 mm fork spanner
6 mm Allen key
5 mm Allen key
Remove the mounting
bolts with a fork spanner
and Allen key.
REMEMBER!
•
•
User guide P9-0157-B
to let all the air out before taking
the wheel apart to repair a
puncture
to secure the bolts with spring
washers
33 of 56
Take the wheel off in the
same way as the back
wheel using a 5 mm Allen
key.
Version 2.0.3/2012
Medema Production A/S
Fuses
The Mini Crosser has the following protection systems:
•
As a safeguard against overheating There are two switches
are integrated in the engine. By incipient overheating speed is
reduced to half power, and by prolonged overheating the scooter
will stop. After cooling for 3 to 5 minutes, the scooter is able to
reach full speed and traction.
•
The control fuse protects against mains faults. It is located under
the rear cover.
•
The main fuse protects against shortcircuits in the main current circuit.
The fuses are located under the rear
cover behind the batteries. Fuse type
DIN 2581 - 100A.
•
If the ignition key is turned at the
same time as the accelerator is
operated, the vehicle will not move off
for safety reasons.
•
The lights and horn are protected by electronic fuses, which
protect against any short-circuiting that may occur. To prevent
accidental short-circuiting when a bulb is changed, the Mini
Crosser must be turned off when the new bulb is fitted and then
turned on again afterwards.
Take the rear cover off. The plastic cover can be removed by squeezing the sides.
Now the fuses can be replaced.
User guide P9-0157-B
34 of 56
Version 2.0.3/2012
Medema Production A/S
Brakes
There are three braking systems on the Mini Crosser M:
•
•
•
Motor brake
Magnetic brake
Handbrake
•
Motor brake: adjusts vehicle speed also when going downhill.
•
Magnetic brake: automatic and comes on when accelerator is
released. It also acts as a parking brake when the Mini Crosser is
at a standstill.
In an emergency, the Mini Crosser can be stopped
instantaneously by turning the key switch. Please note that this
will cause very sharp braking. The rear wheels will lock!
Must not be used in the normal course of driving!
•
Electric safety brake - if the brake is somehow disengaged on
a slope/hill, the Mini Crosser will brake automatically when it
reaches a certain speed. There is an electric safety feature in the
control system, which works even if the battery is disconnected.
This is also the reason why the Mini Crosser cannot be towed at
more than 5 km/h. See the section about towing.
•
Handbrake: intended as an emergency brake and parking
brake. It must be operated with caution when driving in slippery
conditions and downhill.
Disengagement
•
Turn the key to (0) position.
•
Push the disengagement lever at the back down.
The motor brake is now disengaged and the vehicle can be
pushed or towed, but not driven.
NOTE!
The motor brake must never be disengaged on sloping
terrain.
User guide P9-0157-B
35 of 56
Version 2.0.3/2012
Medema Production A/S
if the brake is somehow disengaged on a slope/hill, the Mini
Crosser will brake automatically when it reaches a certain
speed. There is an electric safety feature in the control system,
which works even if the battery is disconnected. This is also the
reason why the Mini Crosser cannot be towed at more than 5
km/h. See the section about towing.
Once the motor brake has been disengaged, the Mini
Crosser can only be braked with the hand brake.
Push the disengagement lever down to
disengage (only handbrake works) and
push up to reactivate the motor (normal
driving now possible).
Disengagement lever
Transporting by motor vehicle
The Mini Crosser must always be restrained and the handbrake
locked during transport in a motor vehicle or trailer.
Avoid lifting by the seat, covers, handlebars and armrests
If you just need to lift the scooter slightly, take hold of it between
the rear lights and by the front bumper.
Secure it in the vehicle with belts attached to the two eyes at
the front and two at the back. All the eyes are marked in yellow.
See the section entitled “Securing to vehicle floor with belts”.
User guide P9-0157-B
36 of 56
Version 2.0.3/2012
Medema Production A/S
Securing to vehicle floor with belts
Dahl Engineering belt set for securing in motor vehicles. Item
No. C2-0242
ALWAYS use four belts at the back and two at the front.
The belts must always be attached to approved fittings in the
vehicle and the four eyes welded to the scooter.
The belts MUST be attached within the angles shown in the
picture for optimum security.
45˚
User guide P9-0157-B
45˚
37 of 56
Version 2.0.3/2012
Medema Production A/S
Attachment point
Attachment point
Greater than
the anchorage
points on the
scooter
Centre line
User guide P9-0157-B
38 of 56
Greater than
the anchorage
points on the
scooter
Version 2.0.3/2012
Medema Production A/S
For transport in an estate car,
the seat can be lifted off and the
handlebars folded down. This
reduces the maximum height to 69
cm.
The Mini Crosser can be used as a seat during transport in
a van or bus, provided it is securely anchored to the vehicle
with approved four-point belts attached to the restraint points
provided on the Mini Crosser.
The Mini Crosser’s restraint points have been tested and
approved in accordance with ISO 7176-19.
The user must also always be independently restrained in the
actual motor vehicle in accordance with traffic legislation rules.
Example
Restraining the
passenger with a static
3-point seat belt:
Secure to the rearmost
retractors.
The shoulder belt must rest
against the collar bone and
fall diagonally to the hip,
where it is secured.
Tighten the belt by pulling on the loose strap. Undo it again by
lifting the buckle. This is the same as on an aircraft.
Retractor
with belt
User guide P9-0157-B
39 of 56
Male and
female parts of
belt done up
Version 2.0.3/2012
Medema Production A/S
Remember to turn the Mini Crosser off during transport. Turn
the key to 0.
However, if at all possible, we recommend that the user
occupies one of the seats in the motor vehicle. All other things
being equal, this is safer.
Transporting by plane
If the Mini Crosser is to be transported by plane, the airlines
require:
•
•
•
the batteries to be flight-approved
the air to be let out of the tyres
the battery leads to be disconnected (not always, but frequently)
The seat and cover have to be removed to disconnect the
battery leads.
A battery declaration for air travel can be found on the Mini
Crosser website:
http://www.minicrosser.dk/Download_brochurer.asp
Towing
If you should be unfortunate enough to break down, the Mini
Crosser can be towed or pushed. The Mini Crosser must
always be turned off and the motor brake disengaged during
towing. See the section on Brakes.
If the Mini Crosser is to be towed, secure a rope to the tow
fitting on the front - marked with a yellow “hook mark”. Do not
tow faster than 5 km/h. The scooter will generate electricity
when it is towed, with the motor acting as a dynamo. If it
is towed at more than 5 km/h, there is a risk of the motor
generating enough electricity to damage the scooter and, in the
worst case, cause a fire.
The Mini Crosser will try to brake if it is towed at more than 5 km/h.
User guide P9-0157-B
40 of 56
Version 2.0.3/2012
Medema Production A/S
1090 mm
Dimensioned drawing, Mini Crosser M2 3W
625 mm
150 mm
190 mm
450 mm
M2 : 305 mm
M2+ : 225 mm
980 mm
526 mm
460 mm
680 mm
1340 mm
M2+ : Equipped with extra large batteries, the foots pace will be
reduced.
User guide P9-0157-B
41 of 56
Version 2.0.3/2012
Medema Production A/S
1090 mm
Dimensioned drawing, Mini Crosser M2 4W
610 mm
175 mm
135 mm
490 mm
M2 : 370 mm
M2+: 290 mm
1030 mm
526 mm
460 mm
680 mm
1400 mm
M2+ : Equipped with extra large batteries, the foots pace will be
reduced.
User guide P9-0157-B
42 of 56
Version 2.0.3/2012
Medema Production A/S
Introduction to seats - Ergo Standard
Lever for seat rotation
Pull the lever back to release
the seat. The seat can then be
turned 90° to either side with a
stop every 45°.
The lever is spring-loaded and the seat locks automatically
when the lever is released.
This lever is located on the right as standard, but can also be
put on the left.
Lever for seat forward/back
Pull the lever out/up to release
the seat on the slide rail.
The seat can then be moved
forward or back as required.
When the lever is released, the seat automatically locks at the
nearest stop.
There is a chock block on the front and back of the slide rail.
Adjusting the angle of the
armrest
The adjusting screw makes it
possible to alter the angle of
the armrest by about 15°.
The arm can be folded right
up to make it easier to get in
and out.
(Height adjustment of the
armrest is an optional extra.)
User guide P9-0157-B
43 of 56
Version 2.0.3/2012
Medema Production A/S
Adjusting the angle of the
backrest
The angle of the backrest can
be adjusted by about 30°. This
can be done by undoing the
adjusting screw and changing
the position of the spacer.
Do the screw up again after
making the adjustment.
Optional extra:
The seat can be fitted with a
gas cylinder for adjusting the
angle of the backrest.
Armrest forward / back:
The armrest can be moved
forward / back on the C-rail.
This can be done by undoing
the screws indicated. Do the
screws up again after making
the adjustment.
Backrest forward / back:
The depth of the seat can be
adjusted. This can be done by
moving the backrest forward
and back while the seat
cushion is held in position.
Undo the screws indicated on
both sides. The backrest can
then be moved as far back as
the edge of the rail and about 15 cm forward. Do the screws up
after making the adjustment. The screws must be at least 2 cm
from the end of the C-rail.
User guide P9-0157-B
44 of 56
Version 2.0.3/2012
Medema Production A/S
Introduction to seats - Mando
Adjusting the angle of the
backrest:
The angle of the backrest can
be adjusted by about 30° by
raising this lever.
Adjusting the angle of the
armrest:
The angle of the armrest can
be adjusted by turning this
screw.
Adjusting the height of the
armrest:
The armrest can be raised/
lowered by undoing the
two screws and moving the
bracket one hole up or down.
Headrest:
The headrest can be raised
and lowered steplessly.
User guide P9-0157-B
45 of 56
Version 2.0.3/2012
Medema Production A/S
Troubleshooting
The following is a list of various problems that, in our
experience, may occur. The list gives possible causes and
remedies.
Problem
Possible causes
Remedy
The Mini Crosser will not
go.
The key has not been
turned to start.
The battery indicator is
not lit.
The batteries are
completely flat.
The control fuse has blown.
The main fuses have blown.
Turn the key and wait 5
sec. before activating the
accelerator.
Charge the batteries.
The Mini Crosser will
not go, but the battery
indicator is lit.
The Mini Crosser has been Wait approx. 1 min. before
overloaded.
trying again. The vehicle
must be turned off (see
section on Fuses).
The handbrake is on.
Release the handbrake.
There is a fault in the
Contact supplier.
electronics.
The batteries are flat.
Contact supplier.
The charging plug has not Remove the charging plug.
been removed.
The driving speed is too
low.
The speed selector is on
slow.
The electronics are
overloaded.
There is too little air in the
tyres.
Change to a faster speed.
There is a problem with
the batteries.
Low temperature.
Charge the batteries and
check that the green lamp
on the charger lights up
before driving off.
Contact supplier.
The driving distance per
charge is too short.
There is a problem with
the charger.
There is too little air in the
tyres.
The charging method is
wrong.
No power to the switch.
The charging lamp on
the charger does not light Fault in cable.
Fault in charger.
up when the charger is
connected to the mains
and the Mini Crosser.
The “ready” lamp on the
charger does not light up
even though the charger
has been on for 10-12
hours.
User guide P9-0157-B
Change the fuse.
Contact supplier.
Stop and wait 3-5 minutes
before starting.
Pump the tyres up to the
right pressure.
Pump the tyres up to the
right pressure.
Read the section on
Charging in the User
Manual.
Turn the switch on.
Contact supplier.
Read the operating
instructions for the charger.
Contact supplier.
There has been a power
cut.
Reconnect the charger
and repeat the charging
process.
The charger is doing a top- Check again half an hour
up charge.
later.
There is a problem with
Contact supplier.
the batteries.
There is a fault in the
Push the charging plug all
charging plug for the Mini
the way in and repeat the
Crosser M2.
charging process. Read
the operating instructions
for the charger.
46 of 56
Version 2.0.3/2012
Medema Production A/S
User guide P9-0157-B
Problem
Possible causes
Remedy
The “ready” lamp on the
charger lights up even
when partly discharged
batteries are connected.
The fuse in the charger
has blown.
The switch in the charging
plug is malfunctioning.
Contact supplier.
The charger lamp is
showing an error.
The charging plug has not
been inserted or there is a
mains fault.
The battery voltage is too
low for charging to start.
Push the charger plug in or
contact the supplier.
Thermometer symbol is
half-red and flashes. The
scooter is running at half
speed.
The motor is overheating
and has reached the limit
of when the first safety
switch responds.
Immediately pull over
at a safe distance from
other traffic and stop the
Mini Crosser. Wait until
the temperature icon
disappears, ca. 3-5 min.
Turn the Mini Crosser off
and on again to continue at
full speed.
Thermometer symbol is
red and illuminated. The
scooter has stopped.
The motor is overheating
and has reached the limit
for when the security
switch shuts the motor off
completely.
If the Mini Crosser has
stopped at an inappropriate
place in traffic, turn on
the emergency lights.
If possible disengage
the scooter and push
it away from traffic. Let
Mini Crosser cool until
the temperature icon
disappears - approx. 3-5
min. Turn the Mini Crosser
off and on again. Now it
can run normally again.
Mini Crosser can not
remember the time.
Battery on main circuit
board has run out of
power.
Contact service technician.
47 of 56
Contact suppliers - read
the operating instructions
for the charger.
Read the operating
instructions for the charger
- or contact the supplier.
Version 2.0.3/2012
Medema Production A/S
If there is an electronic fault, a number of lamps in the battery
indicator will light up. The following table shows what they
mean.
Lamps
Causes
Remedy
1 lamp
The batteries need charging or
the connection to a battery is
poor.
Check all connections between
the controller and batteries. If
these are fine, try charging the
batteries
2 lamps
Poor connection to the motor.
Check the connection between
the motor and controller. Contact
supplier.
3 lamps
Short-circuit between the motor
and a battery connection.
Contact supplier - say how many
lamps are lit.
4 lamps
Not in use
5 lamps
Not in use
6 lamps
Not in use
7 lamps
Accelerator fault.
Contact supplier.
8 lamps
Controller fault.
Contact supplier.
9 lamps
Poor connection to motor
brake.
Check the connections from brake
to controller, or push the brake
lever up.
Check that the vehicle is not
disengaged.
Magnetic brake is disengaged.
User guide P9-0157-B
10 lamps
The controller has been
supplied with a high voltage in
excess of 38 V. Usually seen in
the case of a poor connection.
Check all connections from the
batteries to the controller.
Running
lights
Charger is connected. Remove
charger.
Remove charger.
Running
lights from
the center
and out.
The accelerator has been
activated during start up.
Turn the key back to 0 and to 1 to
reset the fault.
48 of 56
Version 2.0.3/2012
Medema Production A/S
Programming
NOTE! For safety reasons, modifications may only be made by
trained personnel, such as Mini Crosser service engineers and
consultants or authorised service personnel at mobility centres,
etc.
User guide P9-0157-B
49 of 56
Version 2.0.3/2012
Medema Production A/S
Technical data
M2 3W
M2 4W
Transport height without seat
(Steering column folded down)
69 cm
69 cm
Total length:
Total length incl. anti-tilt wheel:
Total width:
134 cm
143 cm
68 cm
140 cm
148,5 cm
68 cm
Total weight incl. batteries and Ergo
Std seat.
151 kg
168 kg
Weight without seat (Ergo Standard
45 cm).
130 kg
147 kg
Dynamic stability in all directions.
10° - 17%
10° - 17%
Kerb climbing
11 cm
11 cm
Max. speed
15 km/h
15 km/h
Braking distance
10 km/h
15 km/h
2.0 metres
3.5 metres
2.0 metres
3.5 metres
Control
S-180
S-180
KW transaxle
0,7 kW
0,7 kW
Turning radius
105 cm
141 cm
Max user weight - standard
175 kg
175 kg
Max user weight inc. assessories HD
version.
------
250 kg
M-127-3-165
13x5.00-6” ext. Ø325 mm
Wheel Norway black - T, E, Nordic,
MaxX, MaxX HD and M-model
4,1 bar
4,1 bar
M-127-3-165P
13x5.00-6” ext. Ø325 mm
Wheel Norway black w/spikes - T,
E, Nordic, MaxX, MaxX HD and
M-model
4,1 bar
4,1 bar
M-127-3-065
13x3.00-8” ext. Ø340 mm
Wheel black - T and M-model
3,5 bar
3,5 bar
General information:
Wheels
User guide P9-0157-B
50 of 56
Version 2.0.3/2012
Medema Production A/S
M2 3W
M2 4W
T-127-3-068
13x3.00-8” ext. Ø340 mm
Wheel black puncture free - T and
M-model
PUR
PUR
Classification, ISO
Class C
Class C
Effective seat width:
Ergo Standard
Spinalus
Mando
HD (user weight max 250 kg)
Ergo child / junior
40,45,50,55,60 cm
40, 45, 50 cm
48 cm
-----35, 37 cm
40,45,50,55,60 cm
40, 45, 50 cm
48 cm
60, 65, 70 cm
35, 37 cm
Effective seat depth:
Ergo, Spinalus and HD seats
Mando
Ergo child / junior
32-52 cm
48 cm
20-30 and 25-40 cm
32-52 cm
48 cm
20-30 and 25-40 cm
Seat back height:
Ergo standrad / HD
Spinalus
Mando
Ergo child / junior
48 cm
56 cm
53 cm
36-41 cm
48 cm
56 cm
53 cm
36-41 cm
Height: front edge of seat to ground
Ergo Standard with slide rail
Ergo Standard without slide rail
Mando seat with slide rail
Mando seat without slide rail
64 - 74 cm
61 - 71 cm
64 - 74 cm
61 - 71 cm
64 - 74 cm
61 - 71 cm
64 - 74 cm
61 - 61 cm
Height: footplate to front edge of seat
Ergo Standard with slide rail
Ergo Standard without slide rail
Mando seat with slide rail
Mando seat without slide rail
45 - 55 cm
41 - 51 cm
45 - 55 cm
41 - 51 cm
45 - 55 cm
41 - 51 cm
45 - 55 cm
41 - 51 cm
Angle of backrest
Ergo standard / HD (manual)
Ergo standard / HD (EL)
Spinalus
Mando
Ergo child / junior
Approx. -5° to +20°
Approx. -5° to +30°
Approx. -5° to +20°
Approx.+5° to +30°
Approx. -5° to +20°
Approx. -5° to +20°
Approx. -5° to +30°
Approx. -5° to +20°
Approx.+5° to +30°
Approx. -5° to +20°
56 Ah batteries
Standard
Standard
Maximum driving distance with new
batteries at +20° on flat, firm surface
40 km
35 km
75/80 Ah batteries
Option
Option
Maximum driving distance with new
batteries at +20° on flat, firm surface
60 km
55 km
Seats:
Batteries:
User guide P9-0157-B
51 of 56
Version 2.0.3/2012
Medema Production A/S
M2 3W
M2 4W
110/115 Ah batteries
Option
Option
Maximum driving distance with new
batteries at +20° on flat, firm surface
80 km
75 km
2 x 12 V / 56 Ah
2 x 12 V / 75 Ah
2 x 12 V / 110 Ah
2 x 12 V / 56 Ah
2 x 12 V / 75 Ah
2 x 12 V / 110 Ah
26.5 x 17 x 22
28.4 x 26.7 x 23
26.5 x 17 x 22
28.4 x 26.7 x 23
Battery weight, 2 batteries
56 Ah
75/80 Ah
110/115 Ah
43 kg
50 kg
80 kg
43 kg
50 kg
80 kg
Energy consumption in kWh, when
charging from “empty”
56 Ah
75/80 Ah
110/115 Ah
Approx. 1.5
Approx. 1.5
Approx. 3.0
Approx. 1.5
Approx. 1.5
Approx. 3.0
Charging device, 24 V DC
56 Ah
75 Ah
110 Ah
6 - 10 A
6 - 10 A
10 - 12 A
6 - 10 A
6 - 10 A
10 - 12 A
Approx. charging time at 20° C
8 hours
8 hours
24 V - 21 W
24 V - 21 W
Optimum battery capacity is
reached after approx. 20 charges /
discharges.
Battery type:
Standard:
Option:
Option:
Max. battery dimensions in cm.
Lighting:
Bulb, headlight
Diode, rear light
24 V - 2 W
24 V - 2 W
Diode, indicator
24 V - 2 W
24 V - 2 W
Standard colour
Grey - metallic
Grey - metallic
The Mini Crosser has been tested for the requirements
described in EN 12184, which are the basis for CE marking.
That means that it has also been tested for the durability
requirements (ISO 7176-8), fire safety requirements (ISO 717616) and the ISO 7176-19 Crash Test.
User guide P9-0157-B
52 of 56
Version 2.0.3/2012
Medema Production A/S
Own notes
User guide P9-0157-B
53 of 56
Version 2.0.3/2012
Medema Production A/S
International addresses
Australia / New Zealand
Germany
Pride Mobility Products
Tel: +61 3 9706-4611
Fax: +61 3 9706-4622
Email: prideaustralia@pride-mobility.com.au
Internet: www.pridemobility.com/international/Australia/australia.asp
Baden Württemberg Bavaria
Draisin GmbH
Tel: (+49) 0 78 41 66 77 0
Fax: (+49) 0 78 41 66 77 88
Email: info@draisin.com
Internet: www.draisin.com/
Belgien
Mobile Belgium
Tel: +32 (0)50 317919
Fax: +32 (0)50 311026
Email: info@mobilescooter.be
Internet: www.mobilescooter.be
Germany
Baden Württemberg
Elofahr Palm
Tel: +49 07225 918 831
Fax: +49 07225 988 070
Mobile: +49 0171 314 7726
Email: uwepalm@web.de
Denmark
Head Office/Jutland
Medema Danmark A/S
Tel: +45 7010 1755
Fax: +45 9718 8835
Email: info@medema.com
Internet: www.medema.dk
Denmark
Zealand
Medema Danmark A/S
Tel: +45 7010 1755
Fax: +45 5664 3388
Email: info@medema.com
Internet: www.medema.dk
Denmark
Funen
Medema Danmark A/S
Tel: +45 7010 1755
Email: info@medema.com
Internet: www.medema.dk
Finland
Respecta OY
Tel: Sales and service +358 (0 )207649748
Email: myynti@respecta.¿
Fax: +358 ( 0 )207649735
Tel: Maintenance - parts and service: +358 ( 0 )207649747
Email : huolto@respecta.¿
France
ICARE
Tel: +33 (0)1 60 78 94 84
Fax:+33 (0)1 69 13 09 78
Email: icarejmb@wanadoo.fr
Internet: http://www.icare-jmb.com
User guide P9-0157-B
Germany
Berlin, Mecklenburg-West Pomerania, Saxony-Anhalt,
Thuringia, Brandenburg and Saxony
Conze Elektro-Mobile
Tel: +49 030 6789 7969
Fax: +49 030 6789 7968
Email: info@elektro-mobile.de
Internet: www.elektro-mobile.de
Germany
Hesse, Rhineland-Palatinate, Saarland and Lower
Franconia
Beromobil GmbH
Elektromobile Treppenlifte
Tel: +49 06123 - 60 57 22
Fax: +49 06123 - 60 57 23
Email: info@beromobil.de
Internet: www.beromobil.de
Germany
Schleswig-Holstein, Lower Saxony and North RhineWestphalia
Wiggers GmbH - Reha / Rollstuhl Werkstatt
Tel: (+49) 0441 36 111 302
Fax: (+49) 0441 36 111 309
Email: wiggers.gmbh@ewetel.net
Internet: www.minicrosser.info; www.ot-wiggers.de
Greece
AMEASHOP
ȉel.: 210 7777545
Fax.: 210 7777835
Mobile: 6970021890
Internet: www.ameashop.gr
Email: faidros@ameashop.gr
54 of 56
Version 2.0.3/2012
Medema Production A/S
Holland
Switzerland
Richard van Seenus Nederland B.V.
Tel: +31 (0) 36 53 20 450
Fax: +31 (0) 36 53 21 308
Email: info@vanseenus.nl
Internet: www.vanseenus.nl
Degonda Rehab SA
Tel: +41 033 345 83 00
Fax: +41 033 345 83 01
Email: info@turbo-twist.ch
Internet: www.turbo-twist.ch
Island
UK
Icepharma HF
Tel: +354 540 8000
Fax: +354 540 8001
Email: icepharma@icepharma.is
Internet: www.icepharma.is
Mini Crosser Ltd
Tel: Sales +(44) 0800 043 0029
Tel: Service & Warranty +(44) 0800 169 9588
Email: sales@mini-crosser.co.uk
Internet: www.mini-crosser.co.uk
Italy
UK
Comfort Online s.r.l. - Società Unipersonale
Tel.: +39 041 5461105
Fax: +39 041 5462098
Email: info@comfortonline.it
Internet: www.comfortonline.it
Active Mobility
Tel.: +(44) 0135 77 44 22
Internet: www.active-mobility.co.uk
USA / Canada
Norway
Medema gruppen AS
Tel: +47 6706 4900
Fax: +47 6706 4990
Email: ¿rmapost@medema.no
Internet: www.medema.no
Pride Mobility Products Corp.
Tel: +1 800 800 8586
Fax: +1 800 800 1636
Internet: www.pridemobility.com
Poland
J.A.S.
Tel.: +48 667 432 282, +48 605 674 017
Fax: +48 33 810 54 58
Email: biuro@jas-bielsko.pl
Internet: http://jas-bielsko.pl/
Spain
Assessorament I Mobilitat. S.L.
Tel: +34 93 666 55 23
Fax: +34 93 666 88 85
Email: info@assessoramentimobilitat.com
Internet: http://www.assessoramentimobilitat.com
Sweden
Minicrosser AB
Tel: (+46) 303 245 200
Fax: (+46) 303 245 228
Email: info@minicrosser.se
Internet: www.minicrosser.se
User guide P9-0157-B
55 of 56
Version 2.0.3/2012
medemagroup
Download PDF

advertising