VALETING MACHINE WET & DRY PC310

VALETING MACHINE WET & DRY PC310
INSTRUCTIONS FOR:
VALETING MACHINE
WET & DRY MODEL No: PC310
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1
ELECTRICAL SAFETY
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1 The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3 Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester.
1.1.4 Ensure that cables are always protected against short circuit and overload.
Yellow & Green
1.1.5 Regularly inspect power supply cables and plugs for wear or damage and check all Earth Wire
connections to ensure that none are loose.
1.1.6 Important: Ensure that the voltage marked on the appliance matches the power supply
Brown
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
Live
1.1.7 DO NOT pull or carry the appliance by the power cable.
Wire
Blue
1.1.8 DO NOT pull the plug from the socket by the cable.
Neutral
1.1.9 DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
Wire
item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is Cable
damaged, cut the cable just above the plug and dispose of the plug safely.
Restraint
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
FUSE RATING 13 AMP
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol
, are fitted with live (brown) and neutral (blue) wires only. To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.1.10 Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your electrician.
1.1.11 If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of 2.5mm² section cable.
1.2














GENERAL SAFETY
Disconnect the machine from the power supply before servicing, changing accessories, or performing any maintenance.
Use only genuine parts and accessories. Unauthorised parts and accessories may be dangerous and will invalidate your warranty.
Maintain the machine in good condition. Use an authorised agent for servicing. Keep machine clean, but DO NOT use solvents.
Ensure the correct Sealey cartridge filter is firmly in place before operating the machine. Wrong cartridge filter may cause machine faults and will invalidate your warranty.
DO NOT allow children or untrained persons to operate the machine.
DO NOT place attachments close to your face (especially eyes, ears, etc). Do not point the hose end at other persons or animals.
DANGER! DO NOT vacuum hot or glowing ash, cigarette ends, inflammable, explosive, corrosive or other dangerous substances.
DO NOT operate the unit without the cartridge filter in place. (See section 5 regarding cartridge filters)
DO NOT leave machine running unattended. Turn power supply OFF, and DO NOT leave the vicinity until motor has come to a complete stop.
DO NOT operate the cleaner while under the influence of drugs, alcohol or impairing medication, or if you are tired.
DO NOT use the cleaner in the rain or in very damp conditions.
When not in use, store the cleaner in a safe, dry, childproof location. DO NOT use the cleaner for a task it is not designed to perform.
Wear protective clothing and gloves.
Original Language Version
PC310
Issue: 3 - 22/10/09
Item Description
16 Rear shampoo tank 1
Handle.
connecting tube
2 Exhaust outlet cover for
17 Shampoo tank.
Cleans carpets, car interiors, fabrics and upholstery. Constructed
HEPA filter
18 Cartridge filter.
from high impact plastic which is dent resistant and rust proof.
3
HEPA filter
19 Shampoo pipe for large Supplied complete with carpet lance, hand-held lance, full wet and
4
Shut-off valve basket.
wash head
dry vacuum accessory kit, including stainless steel telescopic rigid
5
Floating cup valve.
20 Large shampoo head
extension tube, cartridge filter and foam filter. Powerful pump forces
6
Cable storage hook
21 Shampoo spraying nozzle
cleaning fluid into fabric/carpet and 1250Watt suction power leaves
7
Accessory storage position
22 Small shampoo head
surface virtually dry after one pass. Features safety shut-off for wet
8
Extension tube holder
23 Air flow regulator
operation. Large capacity drum with external detergent tank for easy
9 Main switch
24 Extension tube
filling. Fitted with two fixed wheels and two castors. Cable storage
10 Shampoo pump outlet 25 Foam filter
hook, accessories and extension tube holders on head plus
nozzle
26 Combo floor brush
additional accessory stowage slots on base.
11 Vacuum hose inlet.
27 Crevice tool
12 Castor in castor mounting 28 Small utility nozzle
with accessory storage.
29 Suction hose, and shampoo
13 Rear wheels.
delivery tube assembly
3. CONTENTS and SPECIFICATION
14 Rear storage container
30 Tube clip
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PC310 15 Clasp. (x2)
31 Sprayer trigger
Motor: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250W
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V, 50Hz 4. ASSEMBLY
Drum Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20ltr
4.1 Do not connect the mains plug yet.
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10kg
4.2-3 Undo tank clasps and lift off the top section assembly.
Filter - Dry: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cartridge
4.4 Remove contents from inside the tank. Check and identify Filter - Wet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Foam
each component as listed in fig.1. If anything is missing or Replacement Cartridge Filter: . . . . . . . . . . . . . . . . . . . . . . PC310CF
damaged please contact your supplier immediately.
4.5a Insert a large wheel on each side of the rear basket and ensure they are pushed all the way in.
4.5b Turn the tank upside down and insert the moulded castor mountings into their positions in the black base. Retain each castor moulding with the self tapping screws provided.
4.6a For dry suction fit the cartridge filter.
4.6b For carpet washing or wet suction fit the foam filter.
4.7 Re-assemble the top to the tank.
4.8 Fasten the 2 clasps.
4.9 Attach the suction hose to the suction inlet on the front of the tank.
4.10 Push the end of the suction hose into the air diffuser handle. See fig.1-23. Push the end of the air difusser handle into the telescopic extension tube. Fit the required accessory to the base of the extension tube or directly to the difuser handle if the extension tube is not required.
2.introduction
fig.1
Original Language Version
PC310
Issue: 3 - 22/10/09
5. Using a cartridge filter

5.1
5.1.1
5.1.2
7. WET VACUUM CLEANING
WARNING! Always disconnect the plug from the mains supply before removing the tank cover.
IMPORTANT: The filter is made of high quality paper designed to filter small particles of dust. We Recommend that this filter be used for dry vacuuming only.
The filter must be completely dry when used to collect dry dust as a wet or damp filter will clog quickly and be very difficult to clean.
Check the filter carefully and regularly for tears or small holes. Even a small hole can cause dust to be exhausted. Never use a filter with holes or tears as this may cause damage to the motor and invalidate warranty. Replace it immediately.
5.2 Installing & Cleaning
5.2.1 Slide cartridge filter down over filter cage.
5.2.2 Hold the base rim of the filter and gently push and twist it until the top rim fits snug against the lid assembly. Ensure there is no gap between filter and lid assembly.
5.2.3 To remove filter for cleaning, hold the base of the filter and gently pull it off the cage.
5.2.4 Clean dry filter by tapping it on inside of waste can.
6. DRY VACUUM CLEANING

6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8

WARNING! Ensure you read, understand and apply Section 1 ‘Safety Instructions’. Reminder: Remove plug from power supply before opening unit. DO NOT vacuum solvents, explosives, inflammable and/or hazardous liquids such as petrol, oil, spirits, paint, thinners, acids etc. Use of an incorrect filter will invalidate your warranty.
7.1
7.2a
7.2b
7.3
7.4
7.5
7.6
7.7 Ensure the machine is unplugged from the power supply. Make sure the tank is clean and free from dust and dirt.
For wet vacuum cleaning the foam filter must be used.
when using the foam filter first remove any cartridge filter fitted.
Ensure the foam filter is clean and dry. Place the foam filter over the filter cage and adjust carefully.
Fit the required accessories or tubes to the suction hose.
Ensure the switch is 'Off' (position '0') before plugging into the power supply.
Switch to the 'On' (position:
).
When you have completed vacuuming, turn the switch to the 'Off' (position 'O'), and unplug from power supply.
After use, empty the tank and dry.

WARNING! The tank is not designed for liquid storage. Always empty liquids after use. Never store the cleaner with liquid in the tank.
7.8
To vacuum large quantities of liquid, from a sink or tank etc., do not immerse the nozzle completely in the liquid; leave a gap at the top of the nozzle opening to allow an air inflow. The machine is fitted with a float valve which blocks the suction action when the tank has reached its maximum capacity. The user will notice an increase in motor noise. When this happens, turn off the machine, disconnect from power supply, remove the head from the tank and empty the liquid into a suitable receptacle or drain. To continue vacuuming, refit the head and proceed. After wet vacuuming, turn the machine off and remove plug from power supply. Empty the tank and clean/dry the inside and outside before storage.
WARNING! Ensure you read, understand and apply Section 1 'Safety Instructions'.
Reminder: DO NOT vacuum hazardous substances. Use of an incorrect cartridge filter will invalidate your warranty.
Ensure the machine is unplugged from the power supply.
Fit the cartridge filter down over the basket and push it fully home.
Re-position the head onto the tank, and clip in place.
Insert the larger end of the flexible hose into the front inlet on the tank and lock in place.
Push the required attachment onto the free end of the hose.
Plug into the power supply.
Switch the motor to vacuum only (position:
.)
When you have completed vacuuming, turn the switch to the
'Off'. (position 'O'), and unplug from power supply.
Original Language Version
PC310
Issue: 3 - 22/10/09
8.1.1 Ensure the machine is unplugged from the power supply.
8.1.2 Fit the foam filter (F).
8.1.3 Reposition the head onto the tank body and clip in place.
8.1.4 Ensure that the shampoo solution has been mixed with the recommended proportion of water and pour it into the shampoo tank. Insert the shampoo tank connecting tube and filter (fig.1-16) into the tank and push the cap onto the tank filler neck to avoid any shampoo splashing out whilst working.
8.1.5 Plug the nozzle on the other end of the shampoo tank connecting tube into the shampoo inlet hole on the rear of the motor housing below the HEPA filter exhaust cover. ­(fig.1-2)
8.1.6 Ensure that the transparent shampoo delivery tube is fitted correctly around the suction hose and held in place with the clips provided. See also fig.1-29.
8.1.7 Screw the large threaded connector on the end of the flexible suction hose to the vacuum inlet on the front of the tank.
8.1.8 Push the connector on the end of the shampoo delivery tube into the shampoo outlet nozzle on the front of the motor housing.
8.1.9 Slide the spraying trigger fitting into the mount at the top of theextension tube. Push gently and ensure it clicks into place.
Fit the large washing head to the extension tube. Connect the shampoo delivery tube from the head to the trigger. The black fitting is a push and twist fit. See also fig.3.
8.1.10The spraying nozzle at the other end of the delivery tube is a push fit into the mounting on the underside of the head. There is a notch in the nozzle which must fit onto a spiggot in the head mounting to ensure that the nozzle outlet is the right way round.
To clean fabrics and upholstery See fig.2. Clip the spray nozzle with the short tube (See fig.1-21) into the underside of the small cleaning head. Then attach the trigger directly to the mounting on the underside of the small head. Push the assembled head onto the air diffuser handle. Note: The metal extension tube is not used.
8.1.11Select the switch to position
, to operate the pump for shampoo application only.
Select the switch to position
, for simultaneous shampoo application and dirty liquid suction.
8.1.12Squeeze the trigger to apply shampoo to the area to be
washed.
8.carpet CLEANING
fig.2
8.1

SET-UP
Water, mixed with a suitable carpet shampoo solution, is pumped deep into the fibres of the carpet via the shampoo application nozzle. The dirty liquid is then sucked back into the waste tank along with the dirt and grime dislodged by the cleaning solution. Water can be pumped up to 2 meters above the machine so that stairs may also be shampooed.
WARNING! Ensure you read, understand and apply Section 1 'Safety Instructions'.
Reminder: DO NOT vacuum hazardous substances.
8.2
8.2.1
8.2.2
8.2.3
8.2.4
8.2.5
8.2.6
8.2.7
CARPET CLEANING
Vacuum the carpet thoroughly before washing it. For best results we recommend you first remove all furniture from the room to be cleaned, or move it away from the cleaning area.
Clean the whole carpet systematically in squares of approx. 1.5m each. This avoids walking over the cleaned carpet until it completely dry.
Start furthest away from the doorway to the room, extend the hose and work backwards.
Switch to position
, and squeeze the trigger to spray shampoo into the area to be cleaned.
Squeeze the trigger as you pull the head back towards you, in lengths of approx 1.5m. Refill the tank if the fluid spray stops.
Switch off and return to where you started.
Switch to position
to suck up the dirty solution and repeat the previous pattern of strokes. Apply more shampoo in any particularly dirty area. The dirty solution is visible as it is sucked up through the transparent head. Stop vacuuming when there is no more dirty fluid visible.
Do not walk over any newly cleaned area until it is completely dry.
The small washing head is ideal for cleaning sofas, chairs, stairs and car interiors.
fig.3
Original Language Version
PC310
Issue: 3 - 22/10/09




WARNING! DO NOT replace furniture until the carpet is completely dry!
WARNING! DO NOT run the pump when there is no shampoo in the tank!
WARNING! The motor noise changes to a higher pitch when the tank is full or blocked. Stop the machine immediately and empty the water tank.
WARNING! Always use a low foam shampoo or use a
de-foaming agent.
8.3
8.3.1
8.3.2
8.3.3
STORAGE:
Prior to storage, following steps should be taken:
Remove the shampoo head and use the end of the extension tube to suck up any remaining liquid. Run the vacuum cleaner until the tubes and hose are clean and dry.
Switch off the unit and unplug the unit from the power supply. Then empty the main tank and shampoo tank.
Remove the foam filter to dry. Refit for further wet suction. For dry vacuuming you must fit a dry cartridge filter.
9.2.3
9.2.4
9.2.5
A filter that has small holes or tears in it will not perform efficiently and should be replaced.
To clean a dry filter, tap it inside a waste bin. (B)
Do not use a wet cartridge filter for dry vacuuming as the filter will clog quickly. To clean a wet cartridge filter it should be rinsed from the inside (B) and allowed to air dry for 24 hours.
To fit a new/cleaned filter slide it over the filter basket (C) and push it fully home (D).
9.maintenance
9.1
9.1.1
9.1.2
9.1.3
9.1.4
9.1.5
9.1.6
GENERAL MAINTENANCE.
Ensure the machine is unplugged from the power supply.
Disconnect the hose from the container.
Undo the clasps and remove motor head from the container.
Clear out any dirt or debris from the container and hose.
Clean the foam filter by washing it in a mild soapy solution.
Check that the telescopic suction tube operates smoothly, and check the power cable to make sure it has not received any damage.
9.2 CARTRIDGE FILTER MAINTENANCE. (See also section 5)
9.2.1 Handle the filter carefully when cleaning or installing.
9.2.2 Carefully remove the cartridge filter (A) and inspect it for damage. 10. TROUBLESHOOTING
Cleaner will not operate.
No power supply.
Faulty power cable, switch or motor.
Container full of liquid.
Check supply.
Check and repair or replace faulty item.
Empty container.
Dust comes from the motor cover.
Filter missing or damaged.
Fit or replace dust filter.
Reduced efficiency and increased
motor speed/vibration.
Filter clogged.
Nozzle, hose or container inlet blocked.
Clean or replace filter.
Check nozzle, hose and container inlet for blockage.
No solution spraying out.
Switch on wrong position.
Turn switch to the required position.
Shampoo tank is empty.
Incorrectly fitted trigger or pipes.
Add more shampoo.
Check fittings and connections. Ensure there are no
kinks in tubes.
11. CONSUMABLEs
Cartridge Filter (Must be used for dry vacuuming) . . . . . . . . . . . . . . . . . . . . . . . . Model No. PC310CF
Foam Filter (Pack of 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model No. PC200FF10
IMPORTANT! IF THE MACHINE IS USED WITHOUT A CARTRIDGE FILTER FITTED THE MOTOR WILL BURN OUT EVENTUALLY AND
YOUR GUARANTEE WILL BE INVALIDATED. ALWAYS KEEP A SPARE CARTRIDGE FILTER HANDY.
Dust Bags (Pack of 5) Optional Extra . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model No. PC200PB5
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
01284 757500
01284 703534
Web
email
www.sealey.co.uk
[email protected]
PC310
Issue: 3 - 22/10/09
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement