ProForm 831.294250 User`s manual

ProForm 831.294250 User`s manual
PRO-FORM
5 4 5 $
HeartRateControl
Model No. 831.294250
Serial No.
Write the serial number in the space
above for future reference.
TREADMILL
EXERCISER
User's Manual
Serial Number Decal
• Assembly
• Operation
° Maintenance
• Part List and Drawing
Sears, Roebuck and Co., Hoffman Estates, IL 60179
PRO-FORM
5 4 5 s
HeartRateControl
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS .................................................................
BEFORE YOU BEGIN .......................................................................
ASSEMBLY ...............................................................................
TREADMILL OPERATION ...................................................................
HOW TO FOLD AND MOVE THE TREADMILL ..................................................
TROUBLESHOOTING ......................................................................
EXERCISE GUIDELINES ...................................................................
PART LIST ...............................................................................
HOW TO ORDER REPLACEMENT PARTS ..............................................
FULL 90 DAY WARRANTY ...........................................................
Note: An EXPLODED DRAWING is attached in the center of this manual.
2
3
5
6
10
24
26
28
30
Back Cover
Back Cover
IMPORTANT
PRECAUTIONS
3
The decals shown have been placed on your treadmill. If a decal is missing, or if
it is not legible, please call toll-free 1-800-999-3756 and order a free replacement
decal. Apply the decal in the location shown. Note: The decals are not shown at
actual size.
KEEPHANDSAND FEETAWAY
FROMTHISAREAWHILETHE
TREADMILLIS INOPERATION.
4
Protectyourselfand
3thersfrom riskofserious
njury. Read the user's
"nanualand :
BEFORE YOU BEGIN
Thank you for selectingthe revolutionaryPROFORM ®
545s treadmill.The PROFORM 545s treadmillcombines advanced technologywith innovativedesign to
help you get the mostfrom your exercise programin the
convenience and privacyof your home.And when
you're not exercising,the uniquePROFORM 545s
treadmillcan be folded up, requidnglessthan half the
floorspace of other treadmills.
using the treadmill. If you have questionsafter reading
this manual, call 1-800-4-MY-HOME ®(1-800-469-4663).
To help usassistyou, please note the productmodel
number and serialnumber before calling.The model
number of the treadmillis 831.294250. The sedal number can be found on a decal attached to the treadmirl
(see the front cover of this manualfor the location).
For your benefit, read this manual carefully before
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Book Holder
Fan
Accessory Trey
Console
Handrail
Handgrip
Pulse Sensor
Key/Clip
Walking Belt
Reset/Off
Circuit Breaker
Foot Rail
--
Power Cord
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolts
5
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
disposeof the packing materialsuntil assembly is completed. Note: The undersideof the treadmillwalking belt is
coated with high-performanca lubricant.During shipping,a small amount of lubricantmay be transferred to the
top of the walking belt or the shippingcarton. This is a normal conditionand does not affect treadmill performance. If there is lubricanton top of the walking belt, simply wipe off the lubricantwith a softcloth and a mild,
non-abrasive cleaner.
Assembly requires the included allen wre_
rubber mallet _::=:_,
and your own phillips screwdriver (_===_=._,
and wire cutters _:_.
For help identifying assembly hardware, see the drawings below. Note: The assembly hardware and other
small parts are packaged in separate part bags. If a part is not found in the part bags, check to see if the
part has been preattached. If a part is missing, call toll-free 1-800-999-3756.
3/4" Screw (6)-2
3/4" Tek Screw (47)-8
(92)-4
1/4" Star Washer
_
5/16" x 1" Bolt
(122)-4
1/4" x 1" Bolt
(71 )-4
1. With the help of a second person, carefully raise the
Uprights (109) to the position shown.
Insert one of the Extension Legs (128) intothe treadmill
as shown. Make sure that the Extension Leg is turned so
the Base Pad (100) is beneath it. Note: It may be hetpful
to tip the Uprights (109) forward as you insert the
Extension Leg.
Insert the other Extension Leg (not shown) in the same
way.
128
100
6
2. Remove the plastic ties and the wood brace from the
Uprights (109).
I2
Identify the left handrail, which has a hole in the indicated location, and the right handrail. Hold the right
handrail near the right Updght (109), and insert the Wire
Harness (83) into the large hole in the right handrail and
out of the upper end as shown.
122
Brace
Left
Next, hold the right handrail against the right Upright
(109), and hand tighten a 4" Bolt (112) into the right
Upright and the lower end of the right handrail. Tighten
two 5/16" x 1° Bolts (122) into the upper end of the right
handrail and the right Updght. Be careful not to drop
the Bolts into the handrail. Firmly tighten all three
Bolts.
Attach the left handrail as described above. Note: There
is not a wire harness in the left Upright (109).
3. With the help of another person, hold the console assembly near the right Updght (109) and the left Upright
(not shown).
Connect the Wire Harness (83) to the wire harness in
the console assembly. Make sure to connect the connectors properly (see the inset drawing); the conhectors should slide together easily and snap into
place. If the connectorsdo not slide together easily and
snap into place, turn one connectorand try to connect
them again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the
excess wire harnesses back into the right handrail.
Console
Assembl
Rig
Set the consoleassembly on the right Upright (109) and
the Left Upright (not shown). Thread two 1/4" x 1" Bolts
(71) with 1/4" Star Washers (92) into each side of the
console assembly. After you have started all four
Bolts, tighten them,
7
109-
4. With the help of a second person, carefullytip the
Uprights (109) down to the position shown. Make sure
that the Extension Legs (128) remain in the Uprights.
Press the two Base Endcaps (99) into the base of the
Uprights (109). See the inset drawing. Make sure that
the angle of each Endcap matches the angle of the
Upright.
Attach each Extension Leg (128) with two 3/4" Tek
Screws (47) and a Round Base Pad (67) as shown.
(Note: Attach the lower Screw [without the Round Base
Pad] first.) Attach the two Base Pads (100) with four 3/4"
Tek Screws. Note: There are no screw holes in the Base
Endcaps (99). Press firmly on the screwdriver when
tightening the 3/4" Tek Screws (47).
' ,00
t /_.-----1(
//-.
/I
_:/
With the help of a second person, carefully raise the
Uprights (109) so the Base Pads (100) are resting on the
floor.
,1_
,00
p%._
47
/67
>47
99--_
128
109 _'1
5. Remove the knob from the pin. Make sure that the collar
and the spring are on the pin as shown. Insert the pin
into the Latch Housing (75) and tighten the knob back
onto the pin.
76
Raise the Frame (54) to the vertical position. While another person holds the Frame, hold the Latch Housing
(75) against the inside of the Frame. Thread two 3/4"
Screws (6) several turns into the Latch Housing and the
Frame.
Hole
Align the pin with the hole in the Left Handgrip (76) by
sliding the Latch Housing (75) up or down. Make sure
that the pin can be inserted fully into the hole. Hold
the Latch Housing in place and tighten the two 3/4"
Screws (6). Be careful not to overtighten the Screws.
Pull the knob to the right and carefully lower the Frame
(54) to the floor. Press the Latch Cover (12) into the left
side of the Frame. See the inset drawing. Make sure that
the notch in the Latch Cover is positioned over the Foot
Rail (2) as shown.
Note: Over a period of use, the Latch Housing (75) may
need to be adjusted again to align the pin with the hole in
the Left Handgrip (76).
Collar
12
75
54 _
2
Notch
Spring
Knob
54
12
6. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included allen wrenches in a secure place. The large alien wrench is used to adjust the
walking belt (see page 27). To protectthe floor or carpet, place a mat under the treadmill.
If you purchase the optional chest pulse sensor (see page 23), follow the steps below to install the receiver and the short jumper wire included with the chest pulse sensor.
1. Make sure that the power cord is unplugged. Remove
the indicated3/4" Screw (6) and the Access Door (94)
from the back of the Console Back (95).
95
2. Connect the wire on the receiver (A) to the indicated wire
extending from the Console Back (95). Remove the
paper from the adhesive pad on the back of the receiver.
Hold the receiver so the small cylinder is near the
lower edge of the receiver and is facing the Console
Back as shown. Firmly press the receiver onto the indicated corner of the Access Door (94). Note: If there are
two screws included with the chest pulse sensor and two
plastic posts on the inside of the Access Door, attach the
receiver to the plastic posts on the Access Door with the
two screws.
3. Make sure that no wires are pinched. Reattach the Access Door (94) with the 314"Screw (6). The other wires
includedwith the receiver may be discarded.
TREADMILL OPERATION
THE PERFORMANT LUBE TM WALKING BELT
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performancelubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. Such substances will deteriorate the walking
belt and cause excessive wear.
HOWTO PLUG IN THE POWER CORD
an equipment-groundingconductorand a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCl-equipped outlets.
This productis for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustratedin drawing2 may be
used to connect the surge suppressorto a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
Your treadmill, like any othertype of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home's power.
Voltage surges, spikes, and noise interference can
result from weather conditionsor from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local Sears or call 1.800-366-7278 and order
part number 146148.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and t5 amps. There must be a
monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury.
This product must be grounded. If it should malfunction or break down, groundingprovidesa path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having
_€_--_Grounded
Outlet Box
_
_,,,_ ._#_
Surge Suppressor
II
_'1""_]
Grounding Pin
_!:1_]
Grounding Pin I "-_",,,,,,,,,,_
Grounded Outlet
Grounding Plug
2
¢_Grounded
Outlet Box
Adapter
_
Surge Suppressor
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug. or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
10
QUICK
W_NINC:
i
Note: If there is a sheet of clear plastic
on the console, remove the plastic.
FEATURES
START
Key
OF THE CONSOLE
The treadmillconsole offers an impressive array of
features that help you get the most from your workouts.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
the touch of a button. As you exercise, the console will
display instant exercise feedback. You can even measure your heart rate using the handgrip pulse sensor or
the optional chest pulse sensor (see page 23).
Inaddition, the console offers
four preset programs.
Each program automatically controls the speed and incline of the treadmillas it guides you throughan effective workout. Two heart rate programs are also offered.
Each programautomaticallyadjuststhe speed and incline of the treadmillto keep yourheart rate near a target heart rate whileyou exemise.
cable, you can connect the treadmill to your home
stereo, portable stereo, computer, or VCR and play
special iFIT.com CD and video programs (iFIT.com
CDs and videocassettes are available separately).
iFIT.com CD and video programs automatically control
the speed and incline of the treadmill as a personal
trainer guides you through every step of your workout.
High-energy music provides added motivation. To
purchase iFIT.com CDs or videocassettes, call tollfree 1-800-735-0768,
With the treadmill connected to your computer, you
can also go to our Web site at www.iFIT.com and access programs directly from the internet. Additional options are soon to be available. See www.iFIT.com for
more information.
To use the manual mode of the console, follow the
stepsbeginningon page 12. To use a preset program,
see page 14. To use a heart rate program, see page
16. To use an iFIT.com CD or video program, see
page 20. To use iFIT.com programs directly from
our Web site, see page 22.
The console also features iFIT.com interactive technology. Having iFIT.com technology is like having a personal trainer in your home. Using the included audio
11
_lPlug
B
B
in the power cord (see page 10).
Locate the reset/off
circuit breaker near
the power cord. Make
sure that the circuit
breaker is in the reset
position.
._
Reset
Position
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing on page 11)
and slide the cliponto the waistband of your
clothes. Next, route the cord attached to the clip
under the handgrip pulse sensor, and insertthe
key into the console. After a moment, the displays
and various indicatorswill light.Test the clip by
carefully taking a few steps backward ut_til the
key is pulled from the console. If the key is not
pulled from the console, adjust the position of
the clip.
HOW TO USE THE _NUAL
B
walking.As you exercise, change the speed of the
walking belt as desired by pressing the Speed increase and decrease buttons. Each time a button
is pressed, the speed setting will change by 0.1
mph; if a button is held down, the speed setting
will change in increments of 0.5 mph. To change
the speed settingquickly,press the Quick Startbuttons.
To stop the walking belt, press the Stop button.
The Time/Pace display will begin to flash. To
restattthe walking belt, pressthe Start button or
the Speed increase button.
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and align the
walking belt if necessary (see page 27).
B
as desired.
To change the inclineof
the treadmill,press the
Incline buttons. Each time
a buttonis pressed,the
incline willchangeby
0.5%. Note: After the buttonsare pressed, itmay take a moment for the
treadmillto reach the selected incline setting.
MODE
_'.'._ Follow your progress with the matrix, the
training zone bar, and the displays.
Insert the key fully into the console.
The matrix--When the
manual mode or the
iFIT.com mode is selected,the matdxwill
displaya 1/4-miletrack.
As you exercise, the indicatorsaround the track
will light in succession until the entire track is lit.
The track will then darken and the indicators will
again begin to light in succession.
See HOW TO TURN ON THE POWER above,
B
Change the incline of the treadmill
Select the manual mode.
When the key is inserted, the manual
mode will be selected
and the Manual indicator will light. If a program has been
selected, press the Program Select button repeatedly to reselect the manual mode.
The training zone bar-The trainingzone bar
showsthe approximate
intensitylevel of your exercise. For example, if
three to six indicatorsin
the bar are lit, the bar
shows that your pace is
ideal for fat burning.
I_'1 Press
Start the
button
or thebelt.
Speed increase
buttonthe
to start
walking
A moment after the button is pressed, the
walking belt will begin to
move at 1 mph. Hold
the handrails and begin
t2
LSE
S
PACE
Speed display--This
display shows the
speed of the walking
belt.
/,_1 I._ 1
SPEEO-'*
--'
II
J MPH
B
To use the handgrip pulsesensor, first make
sure that your
hands are clean.
Next, stand on
the foot rails
and hold the
pulse bar with
Contacts
your palms on
the metal contacts. Avoid moving your hands. When your
pulse is detected, two dashes (- -) will appear in
the Calories/Pulse display, and then your heart
rate will be shown. For the most accurate heart
rate reading, continue to hold the contacts for
about 15 seconds.
I
display speed and distance in either miles or
,,P.
kilometers.
To find can
Note: The console
which unit of measurement is selected, press
the Stop button while inserting the key into the
console. An "E" for English miles or an =M"for metric kilometers will appear in the display. Press the
Speed increase button to change the unit of measurement. When the desired unit of measurement
is selected, remove the key and then reinsert it.
Note: For simplicity, all instructions in this
manual refer to miles.
Distance/Incline
display--This display
shows the distance that
you have walked or run
and the incline level of
the treadmill, The dis-
•
DISTANCE
O
INCLINE
Note: The pulse bar is intended to be used only
for heart rate measurement. Do not use the
pulse bar as a handlebar. Always hold the
handrails for support when you are not measuring your heart rate.
I
play will change from one number to the other
every few seconds. Note: Each time the incline
changes, the display will show the incline setting
for several seconds.
Calories/Pulse
display--This display
shows the approximate
number of calories you
• CALOR_SES
0 PULSE
have burned. The display will also show your
heart rate when you use the handgrip pulse sensor or the chest pulse sensor. The display will
change from one number to the other every few
seconds.
Fro-IC]
To reset
displays,
press
the Stop button, remove
thethe
key,
then
reinsertthe
Measure
your and
heart
rate
if desired.key.
D
Turn on the fan if desired.
To turn on the fan, press the Fan button. To turn
on the fan at high speed, press the button a second time. To turn offthe fan, press the button a
third time. Note: A few minutes after the walking
belt is stopped, the fan will automatically turn off.
[
B
When
youthe
areconsole.
finished exercising, remove the
key from
Step onto the foot rails,press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage position or the treadmill will be damaged. Next, removethe key from the consoleand put it in a secure place. Note: If the displays and various indicators on the console remain lit after the key is
removed, the console is in the "demo" mode.
See page 23 and turn off the demo mode.
TimelPace display-When the manual mode
or the iFIT.com mode is
-i. l_J]
selected, this display
L_-im.C0 PACE
!-l] 1
• TIME
willshow the elapsed
time and your current
pace (pace is measured in minutes permile). The
display will change from one number to the other
every few seconds. When a program is selected
(except for the Self Select heart rate program), the
display will show the time remaining in the program rather than the elapsed time.
When you are finished using the treadmill, switch
the reset]offcircuit breaker to the off position and
unplugthe power cord.
13
The speed settingfor the
first segment is shownin
the flashing Current
Segment column of the
matrix. (The incline settings are not shown in
the matrix.) The speed
settings for the next four
segments are shown in
the columns to the right.
_11 Insert the key fully into the console.
See HOW TO TURN ON THE POWER on
page 12.
F_
Setect one of the preset programs.
When the key is inserted, the manual
mode will be selected.
To select a personal
u_L
1
trainer program, press
the Program Select button repeatedly until one of the four personal
trainer program indicators lights.
Current Segment
o:o...
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or incline of the treadmill is about to change, the Speed
display and/or the Distance/Incline display will
flash to alert you. When the first segment ends, aft
speed settings will move one column to the left.
The speed setting for the second segment will then
be shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second segment.
Note: If all of the indicators in the Current Segment
column are lit after the speed settings have moved
to the left, the speed settingsmay move downward
so that only the highest indicators appear in the
matrix. If some of the indicators in the Current
Segment column are not lit when the speed settings move to the left again, the speed settings will
move back up.
The diagrams beside the personal trainer program
indicators show how the speed and incline of the
treadmill will change during the programs. When a
program is selected, the Speed display will flash
the maximum speed setting of the program for a
few seconds, and the Distance/Incline display will
flash the maximum Incline setting. The Time/Pace
display will show how long the program will last.
The matrix will will
show the first four
speed settings of the
program.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
[]Press
the Start button or the Speed increase
button to start the program.
If the speed or inclinesetting is too high or too low
at any time during the program, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will light or darken
in the Current Segment column. (If any of the
columns to the right of the Current Segment column have the same number of lit indicators as the
Current Segment column, an additional indicator
may light or darken in those columns as well.)
Note: When the next segment of the program
begins, the treadmill will automatically adjust
to the speed and incline settings for the next
segment.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several time segments of different lengths, One speed setting and
one incline setting are programmed for each segment. Note: The same speed setting and/or incline setting may be programmed for two or more
consecutive segments.
14
To stop the programat any time, press the Stop
button. The Time/Pace display will begin to flash.
To restartthe program, pressthe Start button or
the Speed increase button.The walking belt will
begin to move at 1 mph.When the next segment
of the programbegins,the treadmillwill automatically adjust to the speed and incline settingsfor the
next segment.
r_Turn
See step 7 on page 13,
B
When you are finished exercising, remove the
key from the console.
When the program ends, make sure that the incline of the treadmill is at the lowest setting.
Next, remove the key from the consoleand put it in
a secure place. Note: If the displays and various
indicators on the console remain lit after the
key is removed, the console is in the "demo"
mode. See page 23 and turn off the demo mode.
L_ Follow your progress with the displays.
See step 5 on page 12.
[]Measure
on the fan if desired.
your heart rate if desired.
See step 6 on page 13.
When you are finished usingthe treadmill, switch
the reset/off circuit breaker to the off position and
unplug the power cord.
15
During heart rate programs, the matrix will
show a movinggraphic
that representsyour
heart rate. Each time a
heartbeat is detected,
an additionalpeak will
appear.
I_1 Enter your age.
When a heart rate program is selected, the
word "AGE" and the current age settingwill flash
O CALORIES
0
PULSE
in the Calories/Pulse
display. If you have already entered your age, simplypress the Enter
button. If you have not entered your age, press
the increase and decrease buttons beside the
Enter button to enter your age. Then, press the
Enter button.
r!-!F /-1
_11 Put on the optional chest pulse sensor.
You must wear the optional chest pulse sensor
(see page 23) to use a heart rate program. See
the instructionsincludedwith the chest pulse
sensor.
B
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on
page 12.
B
Enter a maximum
speed.
your age, the letters
1_1 Select a heart rate program.
"SPd" and the maximum
After you
have ofentered
speed
setting
the pro-
When the key is inserted, the manual
mode will be selected.
To select a heart rate
program, press the
Program Select button
repeatedly until one of the two heart rate program
indicators lights.
MpH
_
51_Jl_l]
SPEED
gram will flash in the
Speed display. If desired, press the increase and decrease buttons
beside the Enter button to adjust the maximum
speed setting. When the desired setting is shown,
press the Enter button.
If the 85% Max program is selected, go to step
7. If the Self Select program is selected, go to
step 6.
The diagrams beside the heart rate program indicators show how the target heart rate will change
during the programs. During the 85% Max program, your heart rate will reach approximately
85% of your estimated maximum heart rate; during the Self Select program, your heart rate will remain near a level that you select. Note: Your estimated maximum heart rate is determined by subtracting your age from 220. For example, if you
are 30 years old, yourestimated maximum heart
rate is 190 beats per minute (220 - 30 = 190).
B
Enter a target heart rate.
The letters =PLS" and
the target heart rate settingfor the programwill
flash in the Calories/
Pulse display. If desired,
press the increase and
decrease buttons beside the Enter button to adjust the target heart rate setting. When the desired
setting is shown, press the Enter button.
16
B
Press the Start button or the Speed increase
button to start the program.
If the speed or incline setting is too high or too low
at any time during the program, you can adjust the
setting with the Speed or Incline buttons. However,
each time the console compares your heart rate to
the current target heart rate, the speed and/or incline of the treadmill may automatically change to
bring your heart rate closer to the target heart rate.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each heart rate program is divided into several time
segmentsof different lengths. One target heart rate
is programmed for each segment. Note: If the Self
Select program is selected, the same target heart
rate is programmed for all segments.
If your pulse is not detected during the program,
the letters "PLS" will flash in the Calories/Pulse
display and the speed and incline of the treadmill
may automatically decrease until your pulse is detected. If this occurs, see the instructions included
with the optional chest pulse sensor.
During each segment, the console will reguiady
compare your heart rate to the current target heart
rate. If your heart rate is too far below or above
the target heart rate, the speed of the treadmill will
automatically increase or decrease to bring your
heart rate closer to the target heart rate. If the
speed reaches the maximum speed setting of the
program (see step 5 on page 16) and your heart
rate is still too far below the current target heart
rate, the incline of the treadmill will also increase
to bring your heart rate closer to the target heart
rate.
To stop the program at any time, press the Stop
button. Heart rate programs cannot be stopped
temporarily and then restarted. To use a heart rate
program again, reselect the program and start it at
the beginning.
[]Follow
your progress with the displays.
See step 5 on page 12.
1_1 Turn on the fan if desired.
During the last three seconds of each segment, a
series of tones will sound and the Speed display
and the Distance/Incline display will flash.
See step 7 on page 13.
_]
The program will continue until the last segment
ends. The walking belt will then slow to a stop.
When you are finished
key from the console.
See step 7 on page 15.
17
exercising,
remove the
HOW TO CONNECT
To use iFIT.com CDs, the treadmillmust be connected
to your portableCD player, portable stereo, home
stereo, or computerwith CD player. See pages 18 and
19 for connectinginstructions•To use iFIT.com videocassettes, the treadmill mustbe connected to your
VCR. See page 20 for connecting instructions. To use
iFIT.com programs directly from our intemet site,
the treadmill must be connected to your home computer. See page 19 for connecting instructions.
YOUR PORTABLE
STEREO
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below• If your stereo has a
3.5mm LINE OUT jack, sea instruction B. If your
stereo has only a PHONES jack, see instruction C.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
i'__'i
i _ "-J i
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
Audio
Cable
Adapter
w
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
B
_v
b',
[q:
P -
:
ir
@i
.
................
!
Audio
Cable
•
t
',........
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter (available at electronics stores). Plug the Y-adapter into
the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
•
_
%
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
C
..............
I[
v
,.................
:
i r_ (,_i
i
_
i
t.,
3.5mm _]
Audio
Cable
Y-adapter
|
g
Ir
v
:................_
i r_ ("o) i
i=
Headphones --_,-c:1::_,"
3.5mm
Audio
Y-adapter
i Cable
Headphones-_-[_m-"
t8
|
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5ram LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, sea instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable intothe LINE OUT jack on
your computer.
A
A
9
,......t
[L
r
LMEOUT
@ _
il
k_J i
.
Aud,o
Adapter
....
Aud,o
J
Cable
W
i Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmitl near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the LINE OUT
jack on your stereo.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5ram Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
IlL
v
B
i '_r-_
RCA
['_i
i _) _
i
Audio
Cable
-- Y-adapte_
Hea dphon es/Spea kers ---->-c:l::>J
i
h
i Cable
Y-adapteTAdapter
Wire removed from
LINE OUT jack
19
HOW TO CONNECT YOUR VCR
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 19.
A. Plug one end of the audio cable intothe jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
To use iFIT.com CDs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on pages
18 to 20. Note: To purchase iFIT.com CDs or videocassettes, call toll-free 1-800-735-0768.
Follow the steps below to use an iFIT.com CD or video
program.
A
B
See HOW TO TURN ON THE POWER on page 12.
_100_
h
w
B
i'l_'_i
Audio
i @ I-_'1 i
Cable
Adapter _
B
•
Insert the iFIT.com CD or videocassette.
Press the PLAY button on your CD player or
VCR.
A moment after the button is pressed, your personal trainer wilt begin guiding you through your
workout. Simply follow your personal trainer's
instructions. Note: If the Time/Pace display is
flashing, press the Start button or the Speed increase button on the console. The treadmill will
not respond to a CD or video program while the
Time/Pace display is flashing.
- -,
v
t ................
mode.
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videoeassette, insert the videocassette into your
VCR.
B
i_-"
Select the iFIT.com
When the key is inserted, the manual
mode will be selected.
To use iFIT.com CDs or
videocassettes, press
the iFIT.com button. The
indicator on the button
will light.
"_
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
II
Insert the key into the console.
RCA Y-adapter-
iN©i
AudioAdapter
! ,_,_
: Cable
Wire removed from----}_[:3a=-AUDIO OUT jack
Duringthe CD or video program, an electronic
"chirping"sound will alert you when the speed
and/orinclineof the treadmillis aboutto change.
CAUTION: Always listen for the "chirp" and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
2O
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next "chirp" is
heard, the speed andlor incline will change to
the next settings of the CD or video program.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Pace display will begin to flash. To restart the program,
press the Start button or the Speed increase button. After a moment, the walking belt will begin to
move at 1 mph. When the next "chirp" is heard,
the speed and incline will change to the next
settings of the CD or video program.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
_'._ Follow
with the matrix, the training zoneyour
bar, progress
and the displays.
See step 5 on page 12.
r_
Measure your heart rate if desired.
See step 6 on page 13.
When the CD or videoprogram is completed, the
walkingbelt willstop and the Time/Pace display
will begin to flash. Note: To use another CD or
video program, press the Stop button or remove
the key and go to step 1 on page 20.
Note: If the speed or incline of the treadmill
does not change when a "chirp" is heard:
B
Turn on the fan if desired.
See step 7 on page 13.
f_l
When you are finished exercising, remove the
kay from the console.
See step 7 on page 15.
• Make sure that the iFIT.com indicator is lit and
that the TimelPace display is not flashing. If
the Time/Pace display is flashing, press the
Start button or the Speed increase button on
the console.
CAUTION: Always remove iFIT.com CDs and
videocassettes from your CD player and VCR
when you are finished using them.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the console may not detect the program signals.
21
Hold the handrails, step ontothe walking belt, and
begin walking. During the program, an electronic
"chirping" sound will alert you when the speed
and/or incline of the treadmill is aboutto change.
CAUTION: Always listen for the "chirp" and be
prepared for speed andlor incline changes.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 19. In addition, you must have an intemet connection and an internet service provider. A list of specific system requirements is found on our Web site.
If the speed or inclinesettingsare too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next "chirp" is
heard, the speed and/or incline will change to
the next settings of the program.
Follow the steps below to use a program from our
Web site.
g
To stop the walking belt at any time, press the
Stop button on the console. The Time/Pace display will begin to flash. To restart the program,
press the Start button or the Speed increase button. After a moment, the walking belt will begin to
move at 1 mph. When the next "chirp" is heard,
the speed end incline will change to the next
settings of the program.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 12.
B
Select the iFIT.com mode.
When the key is inserted, the manual
mode will be selected.
To use a program from
our Web site, press the
iFIT.com button. The indicator on the button
wilt light.
When the program is completed,the walking belt
will stop and the Time/Pace display will begin to
flash. Note: To use another program, press the
Stop button end go to step 5.
Note: If the speed or incline of the treadmill
does not change when a "chirp" is heard, make
sure that the iFIT.com indicator is lit and that
the TimelPace display is not flashing, in addition, make sure that the audio cable is properly
connected, that it is fully plugged in, and that it
is not wrapped around a power cord.
l_lGoconnection.
to your computer and start an internet
Lq Start your web browser, if necessary, and go to
our Web site at www.iFIT.com.
_'._ Follow
the desired links on our Web site to select a program.
[]Follow
your
with the matrix, the training zone
bar,progress
and the displays.
Read and follow the on-line instructions for using a
program.
r_
See step 5 on page 12.
_lWhen
you are finished
key from the console.
Follow the on-line instructions to start the
program.
See step 7 on page 15.
When you start the program, an on-screen countdown will begin.
B
Return
to the
and stand
the
foot
pads. Find
thetreadmill
clip attached
to theon
key
and
slide
the clip onto the waistband of your clothes.
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
22
exercising,
remove the
THE INFORMATION MODE/DEMO MODE
THE OPTIONAL CHEST PULSE SENSOR
The console features an information mode that keeps
track of total number of miles that the walking belt has
moved and the total number of hours that the treadmill
has been used. The information mode also allows you
to switch the console from miles to kilometers. In addition, the information mode allows you to turn on and
turn off the demo mode.
An optional chest pulse sensor adds even more
features to the console. The chest pulse sensor provides
hands-free operation and allows the console's heart
rate programs to be used. To purchase the optional
chest pulse sensor, call toll-free 1-800-734-2377.
To select the information mode, hold down the Stop
button while inserting the key into the console.When
the information mode is selected, the following information will be shown:
An "E" for English miles or
an "M" for metric kilometers
will appear in the Speed display. Press the Speed increase button to change the
unit of measurement.
The Distance/Incline display
will show the total number of
miles (or kilometers) that the
walking belt has moved.
T.eTimePace
L!
ispay
show the total number of
hours the treadmill has been
used.
-
TIME
-
O
pACE
IMPORTANT: The CalorieslPulse display should be
blank, If a "d" appears in the display, the console is in
the "demo" mode. This mode is intended to be used
only when a treadmill is displayed in a store, When the
console is in the demo mode, the power cord can be
plugged in, the key can be removed from the console,
and the displays and indicators on the console will automatically light in a preset sequence, although the
buttons on the console will not operate, If a "d" appears
in the CalorieslPulse display when the information
mode is selected, press the Speed decrease button
so the display is blank,
To exit the informationmode, remove the key from the
console.
23
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
1. Hold the treadmill in the locationsshown at the right. To
decrease the possibility of injury, bend your legs and
keep your back straight. As you raise the treadmill,
make sure to lift with your legs rather than your back.
Raise the treadmill about halfway to the vertical position.
2. Hold the treadmillframe firmly with your left hand. Using
your right hand, pull the latch knob to the right and hold it.
Raise the treadmill until the pin on the latch knob is
aligned with the hole in the left handgrip. Then, release
the latch knob. Make sure that the latch knob is fully
released so that the pin is fully inserted into the hole
in the left handgrip. Note: After a periodof use, the latch
housing may need to be adjusted to align the pin withthe
hole in the left handgrip(see assembly step 5 on page 8).
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures
above 85 ° Fahrenheit.
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
pin on the latch knob is fully inserted into the hole in
the left handgrip.
1. Hold the treadmill and place one foot on the base.
2. Tilt the treadmillback until it rollsfreely on the wheels.
Carefully move the treadmill to the desired location.To reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot on the wheel, and carefully lower the
treadmill until the base is resting in the storage position.
24
se
Front Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the treadmill frame firmly with your left hand. Pull
the latch knob to the right. Pivot the treadmill down until
the pin on the latch knob is below the handgrip. Slowly release the latch knob.
Pin
Knob
Handgri_
li_'_Frarne
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. To decrease the possibility of injury, bend your legs and keep your back straight.
25
TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, call toll-free 1-80O-4-MY-HOME ®
(1-800-469-4663).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor,and that the surge suppressor
is plugged into a properlygroundedoutlet (see page 10). Use only a single-outletsurge suppressor that meets all of the specificationsdescribedon page 10. Important:The treadmill is not compatible with GFCI-equipped outlets.
b. Make sure that the key is fully inserted into the console.
C.
Check the reset/off circuitbreaker locatedon the frame near the
power cord. If the breaker protrudes as shown, the circuit breaker
has tripped. To reset the circuit breaker, wait for five minutes and
then press the breaker back in.
Off
Reset
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker located on the treadmillframe near the power cord (see 1. c.
above). If the circuitbreaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console and then reinsert it.
d. If the treadmill stillwill not run, please call toll-free 1-800--4-MY-HOME®(1-800--469-4663).
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. With the helpof another person,
carefullytip the Base (109) down as shown. Remove
the two 3/4"Screws (6) and the two 3/4" Tek Screws
(47). (Note: Your treadmill may not have 3/4" Tek
Screws.) A phillipsscrewdriverwith at least a 5" shaft
is required.
109
•,/47
With the help of another person, carefully raise the
Uprights (69) as shown. Carefully pivot the Hood (39)
off.
26
39
Locate the Reed Switch (24) and the Magnet (18) on
the left side of the Pulley (120). Turn the Pulley until
the Magnet is aligned with the Reed Switch. Make
sure that the gap between the Magnet and the
Reed Switch is about 118". If necessary, loosen the
Screw (25), move the Reed Switch slightly,and then
retighten the Screw. Reattach the Hood (not shown).
Make sure that the Screws are returned to the correct
holes (see drawingA). Run on the treadmillfor a few
minutes to check for a correctspeed reading.
1/8"--
J-
24 _
25_
-
"1_
_
Top
View
--120
_]_
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outletsurge suppressorthat meets all of the specificationsdescribed on page 10.
b.
If the walking belt is overtightenad, treadmill performance may decrease and the walking belt may be
permanently damaged. Remove the key and UNPLUG THE POWER CORD. Using the included allen
wrench, turn both rear roller adjustment bolts counterclockwise 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift the edges of
the walking belt 3 to 4 inches oft the walking platform.
Be careful to keep the walking belt centered. Plug in
the power cord, insert the key, and run the treadmill
for a few minutes. Repeat until the walking belt is
properly tightened.
b
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, please call toll-free
469-4663).
PROBLEM:
The walking
belt is off-center
or slips when walked on
SOLUTION: a. If the walking belt is oft*center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrenchto
turnthe leftrear rollerboltclockwise1/2 of a turn; if
the walking belt has shifted to the right, turn the
left bolt counterclockwise1/2 of a turn. Be carefulnot
to overtighten the walking belt. Plug in the power
cord, insertthe key, and run the treadmillfor a few
minutes. Repeat untilthe walking belt is centered.
b,
If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise
1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side of the walking belt 3 to 4 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key, and walk on the treadmill
for a few minutes. Repeat until the walking belt is
properly tightened.
27
a
b
1-800-4-MY-HOME
® (1-800-
EXERCISE
GUIDELINES
ergy. Only after the first few minutes does yourbody
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the treadmill until your heart rate is near the lowest number in
your training zone.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthenyour cardiovascularsystem, your exercise must be "aerobic." Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, end on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed or incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE
INTENSITY
Whether your goal is to bum fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
HEART
RATE
TRAINING
_65
155
145
140
130
125
I 15
MAX
145
138
130
125
118
110
103
125
120
115
110
105
95
90
20
30
40
50
60
70
80
FAT BURN
Age
Each workout should include the following three parts:
A Warm-up--Start each workoutwith 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparationfor exercise.
ZONES
AEROBIC
FAT BURN
WORKOUT GUIDELINES
Training Zone Exercise--After warming up, increase
the intensityof your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the firstfew
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise--never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your "training zone." The lower two numbers are recommended
heart rates for fat burning;the highest number is the
recommended heart rate for aerobic exercise.
A Cool-down--Finish each workoutwith 5 to 10 minutes of stretchingto cool down. This will increase the
flexibilityof your muscles and will help prevent post-exemise problems.
EXERCISE FREQUENCY
To measure your heart rate during exercise, use the
handgrip pulse sensor.
To maintain or improve your condition,complete three
workouts each week, with at least one day of rest between workouts.After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To bum fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
Dunng the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
28
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch--never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightlyand slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
2. Hamstring Stretch
Sit with one leg extended. Bringthe sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
3. CalflAchilles
Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons and ankles.
4. Quadriceps
Stretch
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks
as possible. Hold for 15 counts, then relax. Repeat 3 times for each
leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
29
PART LISTmModel
NO. 831.294250
R1003A
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
KeyNo.
Qty.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31"
32
33
2
1
1
2
4
56
1
4
1
1
2
1
1
1
2
4
2
1
2
1
7
2
1
1
1
1
1
1
1
1
1
1
5
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
1
2
7
1
1
1
1
1
1
1
t
2
1
11
1
1
Foot Rail Cover
Left Foot Rail
Left Front Endcap
Belt Guide
Belt Guide Screw
3/4" Screw
Console Frame
Cage Nuts
Incline Wire
Warning Decal
Rear Platform Bolt
Latch Cover
Pulse Bar Plate (Left)
Pulse Bar Plate (Right)
Isolator
Platform Screw
Platform Pivot Bolt
Magnet
Caution Decal
Motor Pivot Bolt
Wheel Nut
Frame Spacer
Reed Switch Clip
Reed Switch
Reed Switch Screw
Lift Frame
Motor Tension Nut
Motor
Pulley/Flywheel/Fan
Motor Belt
Motor Assembly
Motor Tension Bolt
Motor Tension Washer/
Lift Pivot Washer
Motor Star Washer
Motor Bracket Bolt
Small Screw
GroundWire
Transformer
Hood
Controller
Power Cord
iFIT.com Wire Nut
iFIT.com Wire
Power Cord Grommet
Static Decal
Reset]Off Switch
3/4" Tek Screw
Belly Pan
Photo Switch Wire
KeyNo.
Qty.
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74*
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
1
1
1
1
1
2
1
1
1
1
2
2
1
1
1
2
1
2
4
2
1
4
1
1
1
1
1
1
1
1
4
4
2
1
2
1
4
1
1
1
2
1
4
2
1
1
1
1
8
2
3O
Description
Filter Wire
Right Front Endcap
Walking Belt
Walking Platform
Frame
Platform Nut
Right Foot Rail
Rear Roller
Right Rear Foot
Allen Wrench
Rear Roller Adj. Bolt
Rear Roller Washer
Right Rear Endcap
Photo Switch
Left Rear Endcap
Small Endcap Screw
Incline Motor
Round Base Pad
Pulse Bar Screw
Isolator Plate
Right Cup Holder (Bottom)
1/4" x 1" Bolt
Right Cup Holder (Top)
Left Cup Holder (Bottom)
Latch Assembly
Latch Housing
Left Cup Holder (Top)
iFIT.com Wire
Jack
Book Holder
Fan Housing Screw
Isolator Plate Screw
Spring Bolt
Wire Harness
Platform Spring
Console Base
Fan Screws
Fan
Console
Fan Housing
Isolator Screw
Key/Clip
1/4" Star Washer
Isolator Cap
Access Door
Console Back
Tie Holder
Releasable Tie
Plastic Tie
Base Endcap
Key No. Qty.
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
4
2
3
2
1
1
2
2
2
1
1
1
2
1
1
1
1
1
2
1
1
4
4
2
1
Description
Base Pad
Clevis Pin
Hairpin Cotter
Rear Roller Star Washer
Decal Plate
Outlet Plate
Wheel Housing
Wheel Bolt
Wheel
Upright
Pulse Bar
Incline Motor Bolt
4" Bolt
Cap Decal
112"Ground Screw
5/16" Allen Wrench
iFIT.com Cable
Motor Bracket
Front Endcap Washer
Front Roller Adj. Bolt
Front RolledPulley
Handrail Washer
5/16" x 1" Bolt
Handrail
Left Handgrip Top
Key No, Qty.
125
126
127
128
129
130
131
132
133
134
135
136
137
#
#
#
#
#
#
#
#
1
1
1
2
1
4
1
1
1
1
1
4
1
1
1
t
1
1
1
1
1
Description
Left Handgrip Bottom
Right HandgripTop
Right Handgrip Bottom
Extension Leg
Incline Stop Bracket
U-Nut
Left Rear Endcap
Power Bracket Screw
Photo Switch Washer
Photo Switch Nut
Lift Motor Pin
Front Endcap Screw
Optic Disk
6" Blue Wire, 2 F
4" Blue Wire, 2 F
4" Blue Wire, M/F
4" Black Wire, M/F
4" Red Wire, M/F
12" Green Wire, FIRing
8" Green Wire, 2 Ring
User's Manual
*Includes all parts shown in the box
# These parts are not illustrated
If a part is missing, call toll-free 1-800-999-3756.
31
o
24
104
39
i
:
52
10
51
50
62
6
-131
61
6
59
6
0
,J
6
=,
C)
0
b)
94
_121
o
126
6
76
92
83
6
92
79
77
o
72
6
¢_
66
o=
99
101
T
6
112
==
. ..=_
...=
_102
101
99
109
\
108--
>9
78
It6
107
19
128
21
108
Your Home
For repair - in your home - of all major brand appliances, lawn and garden equipment,
or heating and cooling systems, no matter who made it, no matter who sold it!
For the replacement parts, accessories, and user's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME ®
(1-800-469-4663)
www.sears.com
Anytime,dayor night
(U.S.A.andCanada)
www.aears.ca
Our Home
For repair of carry-in products like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts and Repair Center.
1-800-488-1222
Anytime,dayor night(U.S.A.only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655
(u.s._)
1-800-361-6665
(Canada)
Para pedir servicio de reparaci6n a domicilio, y para ordenar piezas:
1-888-SU-HOGAR sM (1-888-784-6427)
® Registered Trademark / TMTrademark / sa Service Mark of Sears, Roebuck and Co.
® Marca Regi®rada / TMMarca de F_brica / SMMarca de Servicio de Sears, Roebuck and Co,
FULL 90 DAY WARRANTY
f
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
Sears Treadmill Exerciser, contact the nearest Sears Service Center throughout the United States and
Sears will repair or replace the Treadmill Exerciser, free of charge.
This warranty does not apply when the Treadmill Exerciser is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state•
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
Part No. 204460
R1003A
Printed in USA © 2003 Sears, Roebuck and Co.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement