STM3210C-EVAL STM3210C-EVAL evaluation board Features

STM3210C-EVAL STM3210C-EVAL evaluation board Features
STM3210C-EVAL
STM3210C-EVAL evaluation board
Data brief
Features
■
Three 5 V power supply options:
– power jack
– USB connector
– daughterboard
■
Boot from user Flash, system memory or
SRAM
■
I2S audio DAC, stereo audio jack
■
2 GByte microSD Card™ or bigger
■
Both A and B type smartcard support
■
I2C compatible serial interface 64 Kbit
EEPROM, MEMS and I/O expander
■
RS-232 channel
■
IrDA transceiver
■
USB OTG full speed, USB microAB connection
■
IEEE-802.3-2002 compliant ethernet
connector
■
Two channels of CAN 2.0A/B compliant
connection
■
Inductor motor control connector
■
JTAG and trace debug support
■
3.2” 240x320 TFT color LCD with touch screen
■
Joystick with 4-direction control and selector
■
Reset, wakeup, tamper and user buttons
■
4 color LEDs
■
RTC with backup battery
■
MCU consumption measurement circuit
■
Extension connector for daughterboard or
wrapping board
Table 1.
STM3210C-EVAL
The STM3210C-EVAL evaluation board is a
complete development platform for
STMicroelectronic's ARM Cortex-M3 core-based
STM32F107VCT microcontroller. The range of
hardware features on the board help you to
evaluate all peripherals (USB-OTG FS, ethernet,
motor control, CAN, microSD CardTM, smartcard,
USART, audio DAC, MEMS, EEPROM and more)
and develop your own applications.
Extension headers make it easy to connect a
daughterboard or wrapping board for your specific
application.
Device summary
Order code
August 2010
Description
Reference
STM32F107VCT evaluation
board
Doc ID 17799 Rev 1
For further information contact your local STMicroelectronics sales office.
1/3
www.st.com
3
STM3210C-EVAL
STM3210C-EVAL hardware block diagram
Figure 1 is a block diagram of the STM3210C-EVAL hardware.
Figure 1.
Hardware block diagram
I2S2
3.3V regulator
MCU
consumption
measurement
Audio DAC
I2C1
MEMS
LEDs,Key
EEPROM
GPIO
Joystick
Extension
connector for
GPIOs
I/O expander
Touchscreen
TFT LCD
USB microAB
connector
OTG
MicroSD
Card
SPI3
MC control
connector
MC
USB power
switch
STM32F107VCT
JTAG
MII/RMII
2 BNC connector
Integrated RJ45
connector
CAN1
CAN
transceiver
CAN
DB9 connector
CAN2
CAN
transceiver
CAN
DB9 connector
RS-232
transceiver
USART 2
DB9 connector
Debug
Trace
PHY
ADC
USART2
IrDA
transceiver
Potentiometer
Battery voltage
measurement
USART3
Smartcard
interface
Smartcard
connector
Demonstration software
Demonstration software is preloaded in the board’s Flash memory for easy demonstration of
the device peripherals in stand-alone mode. For more information and to download the
latest version, refer to www.st.com.
Revision history
Table 2.
2/3
Document revision history
Date
Revision
06-Aug-2010
1
Changes
Initial release.
Doc ID 17799 Rev 1
STM3210C-EVAL
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 17799 Rev 1
3/3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement