Quick start guide

for model LS6245

Install the telephone base

Install the telephone base as shown below.

Electrical outlet not controlled by a wall switch

Telephone base power adapter

Telephone wall jack

Battery installation and charging

Install the battery as shown below. For optimal performance, charge the handset battery for at least 16 hours before use.

1.

If the battery compartment cover is on the handset, press on the triangle and slide the cover to remove.

2.

Plug the battery connector securely into the socket inside the handset battery compartment, matching the colorcoded label.

DSL filter (not included) is required if you have DSL high speed Internet service

Telephone line cord

3.

Place the battery with the label THIS SIDE

UP facing up and the wires inside the battery compartment.

4.

Align the cover flat against the battery compartment, then slide it towards the center of the handset until it clicks into place.

Pair your first Bluetooth cell phone

To pair and connect your first Bluetooth cell phone:

1.

2.

3.

4.

5.

6.

7.

8.

Press the MENU softkey on the telephone base.

Press / VOL+ or VOL/ to highlight Bluetooth, then press the SELECT softkey.

Press / VOL+ or VOL/ to highlight Setup cell, then press the SELECT softkey.

Press the NEXT softkey to set the telephone base in discoverable mode.

Turn on the Bluetooth feature of your cell phone and search for or add new devices.

Once your cell phone finds

VTech LS6245, select it.

Enter the telephone base PIN

(the default PIN is 0000) into your cell phone.

When successfully connected,

Device connected to base displays.

BASe

2:22pm 12/25 redIAl menu

Page all HS

Intercom

Bluetooth

Select

Setup cell

Setup headset

Active devices

Select

Pls set your cell to search for devices next lS6245 discoverable

PIn:0000

The pairing process may take up to one minute. If the pairing process fails, try again.

Pairing complete

Telephone base

1.

2.

Use only the power adapter and battery supplied with your VTech telephone.

For complete feature instructions, please refer to your user’s manual.

device connected to base

Pair your first Bluetooth headset

To pair and connect your first Bluetooth headset:

1.

2.

3.

4.

5.

6.

7.

8.

9.

Press the MENU softkey on the telephone base.

Press / VOL+ or VOL/ to highlight Bluetooth, then press the SELECT softkey.

Press / VOL+ or VOL/ to highlight Setup headset, then press the SELECT softkey.

Set your headset to discoverable mode.

Press the NEXT softkey on the telephone base to search for your headset.

Once the telephone base finds your headset, press the

SELECT softkey.

Enter the PIN of your headset

(the PIN for most Bluetooth devices is 0000), then press the NEXT softkey. The screen displays Headset setup

complete.

When the base displays

Connect headset to base?, press the YES softkey.

When successfully connected,

Device connected to base displays.

BASe

2:22pm 12/25 redIAl menu

Page all HS

Intercom

Bluetooth

Select

Setup cell

Setup headset

Active devices

Select

Pls set headset to discoverable mode next

Searching for headset

Select HeAdSet mary’s Headset

Select

The pairing process may take up to one minute. If the pairing process fails, try again.

enter PIn

---- next

Headset setup complete

5.

Charge the handset by placing it in the telephone base. The

CHARGE light is on when the handset charges.

CHARGE light connect headset to base?

yeS no device connected to base

•

More about Bluetooth

You can make and receive calls using the home and cell lines. The home line is your conventional telephone land line. The cell line is the communications service provided through your Bluetooth enabled cell phone.

•

Before using your Bluetooth device(s) with the telephone base, make sure that:

Your cell phone and/or headset devices are not connected to any other Bluetooth device(s) and the

Bluetooth wireless function is on.

Your device is connected to the telephone base and is on the active devices list.

•

•

•

If you experience difficulty using your Bluetooth cell phone:

Make sure that your Bluetooth cell phone is working properly. See your user’s manual of your Bluetooth device for more information.

Delete VTech LS6245 on your cell phone, then delete your cell phone on the paired devices list.

Repeat the pairing process in Pair your first

Bluetooth cell phone in this quick start guide.

Make, answer and end a call

•

To make a home call:

Press /HOME/ FLASH or on the handset and then enter the telephone number.

-OR-

Press /HOME on the telephone base and then enter the telephone number.

•

To predial a home call:

Dial the number and then press

on the handset.

/HOME/ FLASH or

-OR-

Dial the number and then press /HOME on the telephone base.

•

To answer a home call:

Press

-OR-

/HOME/ FLASH or on the handset.

Press /HOME on the telephone base.

-OR-

Press the call button on your headset if you have a

Bluetooth headset connected.

•

To end a home call:

Press OFF/ CLEAR telephone base.

or put the handset in the

-OR-

Press /HOME on the telephone base.

-OR-

Press the call button on your headset.

To make a cell call:

1.

Press /CELL on the handset or telephone base, then enter the telephone number.

2.

Press the DIAL softkey.

•

To predial a cell call:

Enter the telephone number, then press /CELL on the handset or telephone base.

•

To answer a cell call:

Press /CELL on the handset or telephone base.

•

To end a cell call:

Press /CELL on the handset or telephone base.

Important notes

Auto keylock: To prevent accidental key presses, the handset keys automatically lock after 10 seconds without presses. Press the UNLOCK softkey to unlock the keypad.

Dialing 911: You must unlock the keypad before you can dial 911 or any other number on the handset.

HAndSet x on

Press unlocK to use keys unlocK

Turn the answering system on or off

The answering system must be turned on to answer and record messages.

To turn on or off with the telephone base:

1.

Press the MENU softkey.

2.

3.

Press / VOL+ or VOL/ to highlight Ans. system, then press the SELECT softkey.

Press / VOL+ or VOL/ to highlight Ans sys setup, then press the SELECT softkey.

4.

5.

Press / VOL+ or VOL/ to highlight

Answer ON/OFF, then press the SELECT softkey.

Press / VOL+ or VOL/ to choose On or Off, then press the SET softkey.

To turn on or off with a handset:

1.

Press the MENU softkey.

2.

3.

Press / VOL+ / or CID/VOL/ to highlight

ANS. SYSTEM, then press the SELECT softkey.

Press / VOL+ / or CID/VOL/ to highlight

Ans sys setup, then press the SELECT softkey.

4.

5.

Press / VOL+ / or CID/VOL/ to highlight

Answer ON/OFF, then press the SELECT softkey.

Press / VOL+ / or CID/VOL/ to choose On or Off, then press the SET softkey to confirm.

•

Message playback

To play messages with the telephone base:

Press to listen to messages.

Options during playback:

•

• Press / VOL+ or VOL/ to adjust the

speaker volume.

Press to skip to the next message.

•

• Press CANCEL / to repeat the message currently

playing. Press CANCEL / twice to listen to the

previous message.

• Press FLASH /X to delete the current message.

The system advances to the next message.

Press to stop.

To play messages with a handset:

1.

Press the MENU softkey.

2.

3.

Press / VOL+ / or CID / VOL/ to highlight

ANS. SYSTEM, then press the SELECT softkey.

Press / VOL+ / or CID / VOL/ to highlight

Play msgs, then press the SELECT softkey.

Options during playback:

• Press / VOL+ / or CID / VOL/ to adjust the

speaker volume.

•

•

•

Press 6 to skip to the next message.

Press 4 to repeat the message currently playing.

Press 4 twice to listen to the previous message.

Press 3 to delete the current message. The

system advances to the next message.

•

•

Press 5 to stop.

Press the BACK softkey to exit and return to the

previous menu.

IMPORTANT!

•

•

If the LS6245 system is not working properly:

Refer to the Troubleshooting section of the user’s manual.

Visit our website at www.vtechcanada.com or call 1 (800) 267-7377.

The Bluetooth ® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by VTech Holdings Limited is under license. VTech

Holdings Limited is a member of Bluetooth SIG, Inc.

Other trademarks and trade names are those of their respective owners.

Copyright © 2009 for VTECH TELECOMMUNICATIONS LTD.

96-007147-020-100