NEXO S. A. NEXO LatAM NEXO Asia Parc D’Activité

NEXO S. A. NEXO LatAM NEXO Asia Parc D’Activité
NEXO S. A.
Parc D’Activité
du Pré de la Dame Jeanne
B.P.5
60128 PLAILLY
France
Tel: +33 (0)3 44 99 00 70
Fax: +33 (0)3 44 99 00 30
E-mail: info@nexo.fr
NEXO LatAM
C.C. No 33. Suc 49
Caballito (1449)
Buenos Aires
Argentina
Tel: +54 114 432 1911
Fax: +54 114 431 1007
E-mail: info@nexo.fr
NEXO Asia
GPO Box 806
Hong Kong
SAR China
Tel: +852 9096 3472
Fax: +852 2104 3214
E-mail: info@nexo.fr
PS R2 Series Systems
www.nexo.fr
www.nexo.fr
NEXO PS R2 Series Systems
First we set the standard.
Now we’re raising the bar.
For more than 15 years, the NEXO PS Series has set the standard for compact, high-output loudspeakers.
Now NEXO is raising the bar. The new PS R2 Series builds upon the groundbreaking performance of its predecessor
with even more power and bandwidth, greater versatility and better value in both installed sound and touring applications.
More
Power and bandwidth
More than 200,000 NEXO PS Series speakers are already hard at work around the world in applications where compact,
high-output, linear response loudspeakers are required. Now the new PS R2 Series delivers as much as a 5dB higher
sound pressure levels from a range comprising three scalable systems, all of which can be quickly and easily configured
for main PA use, for use as floor monitors, or flown vertically or horizontally in installations or for use as side/rear fills.
The PS R2 Series offers the user a totally integrated loudspeaker solution, in which innovative transducer, waveguide
and enclosure designs come together under the control of strategic equalisation from new, dedicated TD Controllers to
ensure extended bandwidth and sound pressure levels, along with a high degree of speaker protection.
3
NEXO PS R2 Series Systems
The Asymmetrical Advantage
A satisfactory audience experience often necessitates a compromise
between the wide, short throw coverage required by listeners closest to
the stage, and the narrow, long throw coverage required by those at the
back of the venue. Similarly, coverage from monitors must be wider
when the performer is closer to the speaker, and narrower when further
away. The asymmetrical horns used in all PS R2 Series speakers are
engineered such that the vertical coverage is narrower above horn axis
Front-of house configuration
than below. A few minutes is all it takes to remove the grille, unscrew
the horn and rotate it to ensure optimum directivity in every application.
When used as the main PA, PS R2 systems significantly reduce the
amount of ambient, reverberant energy caused when loudspeakers
misdirect their output towards walls and ceilings. And in monitor mode,
more of the output can be focussed on the performer.
Stage monitor configuration
+30º
50º
+25º
100º
-25º
-30º
100º
50º
Greater
Versatility
Central to the advanced performance of the PS R2 Series is NEXO’s Asymmetrical Dispersion Constant Directivity horn design. Quick and easy
for the user to rotate, it focusses more of the output of the loudspeaker on the audience (or performer when used as a monitor), greatly
increasing the versatility of the system without compromising its performance in any given application.
4
In conventional Front Of House configuration, a PS R2 Series loudspeaker
yields 50° horizontal coverage at 25° above the centre line. Rotating the horn
expands this to 100° at 50° below the centre line, such that coverage narrows.
In stage monitor mode, a PS R2 Series loudspeaker yields 100°
horizontal coverage at 30° above the centre line, narrowing to 50°
horizontal coverage at 25° below the centre line for use when the
performers are further away.
A sticker on the wide dispersion side of the horn indicates the correct orientation for FOH and wedge monitoring applications. The arrow on the sticker indicates
the ‘wide side’ of PS horn dispersion. Users simply need to position the arrow such that it points in the direction requiring widest coverage, and away from the
direction requiring narrowest coverage.
5
NEXO PS R2 Series Systems
A better
Investment
PS Series loudspeakers have a hard-earned reputation for performance and reliability, with countless examples performing night-in, night-out, for
more than a decade, without a single problem. Built in NEXO’s new, state-of-the-art production facility in France and engineered from the outset
for a long, trouble-free life, the new PS R2 Series is set to enhance this reputation yet further through a combination of even more exacting
manufacturing standards and advanced driver protection technology.
Rental Revenue
Faster
Set up
The versatility of PS R2 Series loudspeakers is enhanced yet further by a full range of rigging and flying hardware
(see pages 20/21) – the development of which benefits from NEXO’s 30 years of experience in touring sound systems.
And system installers will discover a similarly comprehensive range of mountings for permanent installation.
In fixed installations, analogue controllers ensure accurate reproduction at high output levels, while mobile sound
operators may choose to use NEXO powered TDControllers (see page 22), with their enlarged library of presets for
instant access to popular configurations.
Purchase Price
Resale Price
Originally purchased in 1995, this ‘first generation’
PS15 gave 11 years of problem-free rental service
before being resold in 2006.
NXAMP 4x4 Powered TDController
6
7
NEXO PS R2 Series Systems - PS8
PS8 Loudspeaker
Key Features
LS400-SUB Sub-Bass
Key Features
• High-power system (125dB Peak SPL @ 1m)
with new 8in LF and 1in HF low magnetic
emission Neodymium drivers for light weight
(7.5kg, 16.5lbs) and negligible magnetic leakage.
• Rotatable, asymmetrical horn and unique cabinet
architecture ensure versatility; user-adaptable for
both PA and stage monitoring applications.
• Two-way passive 8Ω design uses a single
amplifier channel for simpler installation and
lower cost.
• Sophisticated control electronics ensure reliable,
linear operation. Supported with a full range of
mounting and flying accessories.
• High-power system (131dB Peak SPL @ 1m)
with 12in VLF low magnetic emission
Neodymium driver for light weight (14.6kg,
32lbs) and negligible magnetic leakage.
• VLF extension (to 40Hz) of PS8 Loudspeakers.
Sophisticated control electronics ensure
reliable, linear operation.
• Integral pole mount that supports one or two
PS8 Loudspeakers.
Architectural and Engineering Specifications
The 2-way full range loudspeaker system shall have one 8 inch
shielded neodymium cone transducer and a 1 inch shielded
neodymium compression driver on a low distortion constant
directivity asymmetrical dispersion horn. The system's horizontal
coverage shall range from 50° to 100°, with vertical coverage of
+25° and -30°. The user shall be able to rotate the horn in 4
directions as required by the application. The system shall have a
Q of 10 and a Directivity Index that is 10 at frequencies above
1.8kHz. Nominal Sensitivity shall be 96dB (94dB wideband).
When driven by a NEXO NXAMP 4x1, NXAMP 4x4 a PS8
TDController or by a NX242 properly connected to amplification
capable of delivering 200 to 500 Watts into an 8Ω (nominal) load
the system shall be capable of 122dB to 125dB peak SPL, with a
frequency response of 69Hz to 19kHz ±3dB (62Hz to 20Hz 6dB). The system shall include an internal passive crossover.
Electrical connections shall be made via one of the two 4-pole
NL4MP SPEAKON connectors.
The system shall have a tuned ported multi-angle enclosure
constructed of 18ply Baltic birch, finished in textured black or
white coating and having exterior dimensions no greater than
406mm H x 250mm W x 219mm D (16.0in H x 9.8in W x 8.6in
D): the system shall weigh 7.5kg (16.5lbs). Exterior hardware
shall include 3 mounting points (2 on the top, 1 on the bottom), 6
mounting points on the sides and 1-pole socket. Interior
components shall be protected by a powder coated perforated
steel grille. The system shall be the PS8 with a PS8 TDController,
NXAMP 4x1, NXAMP 4x4 or NX242.
Architectural and Engineering Specifications
LS400-SUB Sub-Bass
The PS8 features advanced NEXO designed low magnetic emission Neodymium drivers, making
the PS8 extremely light and compact while usable next to magnetically-sensitive professional
video or computer equipment. The dispersion, architecture and weight balance are designed to
provide uncompromised PA and stage monitor performance from a single speaker, and
background and foreground music playback applications are equally well-served.
Like the new PS10-R2 and PS15-R2, this flexibility
is realized by a proprietary constant directivity
asymmetrical dispersion horn, easily configurable
(by users) in four positions by 90° rotations.
Coupled with the horn’s unique progressive
horizontal (50° to 100°) and vertical (55°) dispersion,
the most suitable pattern can be selected for vertical
or horizontal PA usage or wedge monitoring. The
PS8’s 2-way passive 8Ω design employs a single
amplifier channel to deliver bi-amped performance,
reducing system cost, size and complexity, and a
new grille design increases durability while fully
accommodating use as a wedge.
The LS400 Sub-Bass extends the usable range of the PS8 Loudspeaker to 40Hz, providing high
performance and high power output (131dB Peak) in an extremely compact, light weight
package. The NEXO-designed shielded 12in Neodymium driver allows the LS400 to be used in
close proximity to magnetically sensitive video equipment.
One LS400 is typically used with two PS8 loudspeakers, additional units may be used for an enhanced LF
impact. The PS8 TDController’s integral sub section and combined signal (PS8 and LS400) Speakon
wiring ensure cost-effective and simple system implementation.
The sub-bass loudspeaker system shall have one 12in VLF
shielded long excursion neodymium cone transducer. Nominal
Sensitivity shall be 99dB. When driven by a NXAMP 4x1,
NXAMP 4x4 a PS8 TDcontroller or by a NX242 properlyconnected to amplification capable of delivering 300 to 700
Watts into a 6Ω (nominal) load the system shall be capable of
128dB to 131dB peak SPL, with a frequency response of 43Hz
to 120Hz ±3dB (40Hz to 140kHz -6dB). The system shall
include an active crossover. Electrical connections shall be
made via one of the two 4-pole NL4MP SPEAKON connectors.
The system shall have a tuned ported rectangular enclosure
constructed of 18ply Baltic birch, finished in either black or
white textured coating and having exterior dimensions no
greater than 338mm H x 500mm W x 406mm D (13.3in H x
19.7in W x 16.0in D): the system shall weigh 19.3kg (43 lbs).
Exterior hardware shall include 1-pole socket. The system shall
be the NEXO LS400 with either the PS8 TDController, NXAMP
4x1, NXAMP 4x4 or NX242.
PS8 horizontal coverage, +25°
LS400 response
LS400 impedance
PS8 + LS400 response
PS8 + LS400 impedance
System Applications
• Installed PA for clubs, A/V, theatre, broadcast,
Houses of Worship, theme parks, etc.
PS8 horizontal coverage, 0°
• High-quality, low-profile stage monitoring for
clubs, A/V, theatre, broadcast, etc.
• Near-field, down-fill and under-balcony
systems in support of larger systems.
• Foreground and background music source for
retail establishments seeking audio with impact.
• Anywhere powerful, high-quality performance is
required near to magnetically-sensitive equipment.
8
PS8 horizontal coverage, -25°
9
NEXO PS R2 Series Systems - PS8
PS8 Loudspeaker Specifications
LS400-SUB Sub-Bass Specifications
PS8 TDController Specifications
Product Features
Components
Product Features
Components
Product Features
Audio Inputs
Height x Width x Depth
Weight
Connectors
Construction
Fittings
PS8 TDController
Stand fittings
The PS8 TDController is an advanced analogue processor that allows the PS8 Loudspeaker and
optional LS400 Subwoofer to achieve superior performance from an exceptionally small format.
The PS8 TD provides crossover, sensed amplifier control and system equalization, optimised for
the PS8 and LS400. Each PS8 TD has two inputs and three outputs, L, R and summed sub out,
minimising installation cost and complexity.
Key Features
• Precision circuits specifically engineered for the
PS8/LS400 systems permit increased SPL and
operational reliability.
• Servo-controlled VCEQs provide precise dynamic
control without spectral imbalance.
• Two inputs and three outputs enable a single PS8
TD to manage multiple PS8 and LS400 products.
• Comprehensive status indicators and controls.
Like all NEXO processors, the PS8 TD provides precision dynamic, voice coil temperature and diaphragm
displacement protection through the use of selective Voltage Controlled Equalisers (VCEQs), strategically
reducing levels only at frequencies when and where necessary.
LF 1 x 12" ( 30cm ) long excursion
6Ω driver
338mm x 500mm x 406mm
Height x Width x Depth
(13 1/4" x 19 5/8’" x 16")
19.5 kg (43 lbs)
Weight
2 x NL4MP SPEAKON 4 pole
Connectors
Construction
Baltic Birch Ply & textured
black coating
2 Metal Handles
Fittings
Stand fittings
Internal Stand Fitting on Top (35mm /
1 3/8") allows pole mounting of 1 PS8.
System Specifications LS400 with PS8 TDController
Frequency Response [a]
43 Hz - 120 Hz ±3dB
40 Hz - 140 Hz
Usable Range @-6dB [a]
99 dB SPL Nominal
Sensitivity 1W @ 1m [b]
Nominal Peak SPL @ 1m [b] 128 to 131 dB Peak
Crossover Frequencies
120 Hz Active through PS8TDController
6Ω
Nominal Impedance
Recommended Amplifiers
300 to 700 Watts / 4Ω
Sense Inputs
Audio Outputs
Controls
Indicators
Dimensions
Weight
Specifications
Output Level
Input Section
THD+N
Noisefloor
Dynamic Range
Crosstalk
Filtering & EQ.
Protections
The PS8 TDcontroller shall be configurable from a combination of 2x inputs and 3x outputs with each output providing crossover, parametric EQ,
adjustable peak limiter and Temperature & Displacement protection for NEXO PS8 and LS400 products. The unit shall have electronically balanced
analogue inputs and outputs. All crossover, protection parameters, and EQ are factory optimized and can't be user-accessed. The controller must
model the loudspeakers in real time and this modeling shall include loudspeaker temperature and displacement. Protection shall be selective,
acoustically transparent and not allow PS8 loudspeakers to exceed speaker-dependent thresholds. The device shall have 3x inputs providing
feedback from amplifier output to allow real time monitoring of amplifier voltage. Crossover function between PS8 loudspeakers and the LS400
Subwoofer shall be controlled by the PS8 TDcontroller. Maximum input shall be 22dBu with CMRR 90dB@1kHz and noise floor below -100dB for
the 0dB rear-panel switch. A 3-position, rear-panel gain control switch shall be adjustable between -6/0/+6dB. The Output Section shall display
+22/+16/+10dBm into 600Ω load with Rear Panel switch on +6/0/-6dB (respectively). LEDs shall indicate status for; Power ON (green), Amp
Sense & Peak LED's (green/Red), Temperature & Displacement (yellow) and LS400 (VLF) displacement protection (also yellow). The chassis shall be
constructed of steel with a black paint finish. Input power shall range from 110 to 220VAC continuously, 50-60Hz with a rear panel earth-lift. The
1RU controller shall weigh 2.9kg(6.4lbs), with exterior dimensions of 483mmW x 44mmH x 190mmD (19" x 1.75" x 7.5"). The chassis shall be
constructed of steel with a black paint finish. The controller shall be the NEXO PS8 TDcontroller. The unit shall be UL approved and comply with
electrical international standard (CB scheme) based upon the European standard EI60065. The unit shall fulfill the electromagnetic requirement of
the harmonized standards EN55013, EN55020 and of the requirement of the FCC PART 15 CLASS b regulation. Other integrated loudspeakercontrollers shall be acceptable, provided independent laboratory test results verify these specifications are equaled or exceeded.
Power Supply
Conformity
System Operation
Electronic Controller
Dispersion configuration
Sub-bass
Speaker Cables
Two differential non floating L&R Audio
inputs, 50 kOhm. Two XLR-3F
connectors.
Three Amplifier Sense Inputs (PS8 L&R,
LS400). 400 kOhm. 6 Pole Removable
Strip Terminal.
Two L&R PS8 Audio outputs. Balanced,
non floating, 51 Ohm. Two XLR-3M.
One Mono (L+R) LS400 Audio output.
Balanced, non floating, 51 Ohm. One
XLR-3M.
Gain switch (back panel), 3 positions : -6
/ 0 /+6dB. Peak Limiter trimmer (600W200W/8 Ohms)
Sub Overlap / Crossover switch & Sub
Gain Control (-/+ 6dB).
LF speakers Protect Yellow LED's (Temp.
& Disp), Power ON (green),
Amp Sense & Peak LED's (green/Red)
1U 19" Rack. 165mm (6.5") Depth
2.9 kg (6.6 lbs) net
+22 /+16/+10 dBm typ. into 600 Ohm
load. Back Panel switch on +6/0/-6dB
respectively.
Maximum input Level : 22dBu. CMRR
90dB @ 1kHz typ.
0.05% @ 1kHz Typ. for +10dBm Output
-90 /-96 /-100 dBV for +6 /0 /-6dB
switch position (22 Hz - 22 kHz,
UnWeighted)
111 dB UnWeighted (THD+N at-60dBr
sine wave @1kHz rel.max. output)
104dB
L&R: 12dB/oct Low Pass, 12dB/oct High
pass (crossover or overlap), 4 Parameter
EQs. All factory tuned
VCA temp. (SUB,LF & LF), VCEQ disp.
(SUB & LF), Peak Limiter (all chanels),
Power compression regulation
100-250 Volts (continuous operation),
50-60Hz. Power 9W. Peak Inrush current
0.5A. Earth-Lift.
Comply with safety objective of
73/23/EEC & 89/336/EEC directives.
(EN60065-1998, EN55103-1996) CB
scheme, cULus certifications in progress
The PS8 TDController is precisely matched to the PS8 & LS400 cabinets and includes sophisticated protection systems. Using PS8 & LS400 without a properly connected PS8TD will result in poor
sound quality and can damage the components. PS8 & LS400 can also be used with NXAMP4x1 and NXAMP4x4 Powered TDControllers.
After dismounting the front grille from its fixings, the HF Horn can be rotated in 4 positions for dispersion configuration.
The PS8 can be used without optional LS400 Sub-bass. Active two-way operation with the LS400 is included in the PS8TD. One LS400 matches 2 x PS8, additional LS400 may be used for enhanced
LF capability.
PS8 are wired 2- & 2+ on Speakon connectors, LS400 on 1- & 1+. Loop through Speakons are present on both. Single identical cables can thus be used to loop through combinations of up to 2 x PS8
& 1 x LS400 in no particular order.
As part of a policy of continual improvement, NEXO reserves the right to change specifications without notice.
[a] Response curves & data : Anechoic Far Field for the PS8 + PS8TD. Half-Space Anechoic radiation for the LS400 + PS8TD.
[b] Sensitivity & Peak SPL data : these will depend on spectral distribution and crest factor of program material. Measured with band limited Pink Noise.
Nominal refers to Voice Decade (300 Hz - 3 kHz), Wideband to the specified ±3dB range. Data are for speaker + processor + recommended amplifier combinations.
Peak SPL is at clipping of recommended amplifier.
[c] Directivity curves & data : obtained by computer treatment on off axis response curves.
E&OE September 2009.
MONO
10
System Specifications PS8 with PS8 TDController
Frequency Response [a]
69 Hz - 19 kHz ±3dB
Usable Range @-6dB [a]
62 Hz – 20 kHz
96 dB SPL Nominal - 94 dB SPL
Sensitivity 1W @ 1m [b]
Wideband
Nominal Peak SPL@1m [b] 122 to 125dB Peak
HF Dispersion [c]
50° to 100° Hor. x 55° Vert.
Rotatable Horn, 4 positions
Directivity
Q : 10 Nominal DI : 10 dB Nominal
( f > 1.8 kHz )
Crossover Frequencies
2.5 kHz Passive
Nominal Impedance
8Ω
Recommended Amplifiers
200 to 500 W / 8Ω
Architectural and Engineering Specifications
System configurations
PS8/LS400 with NXAMP 4x1
LF 1 x 8" (20 cm) Shielded Neodymium
8Ω driver
HF 1 x 1" Shielded Neodymium throat
driver + Low Distortion, Constant
Directivity Asymmetrical Dispersion Horn.
406mm x 250mm x 219 mm
(16" x 9 7/8" x 5 5/8")
7.5 kg (16.5 lbs)
2 x NL4MP SPEAKON 4 pole
Baltic Birch Ply finished with textured
black coating
Handles - Front finish: Moulded Dark
Grey Metal Grill
Flying Points & Fixed Installation
Threaded inserts are fitted as standard to
all cabinet surfaces for connection of
mounting accessories
Built-in Stand Fitting, (35mm / 1 3/8")
STEREO
PS8/LS400 with PS8 TDController
11
NEXO PS R2 Series Systems - PS10-R2
PS10-R2 Loudspeaker
Key Features
LS600-SUB Sub-Bass
Key Features
• High-power system (132dB Peak SPL@1m)
with 10in LF and 1in HF drivers.
• Rotatable asymmetrical horn and unique
cabinet architecture ensure versatility.
• User-adaptable for both PA and stage
monitoring applications.
• Two-way passive 8Ω design uses a single
amplifier channel for simpler installation and
lower cost.
• Sophisticated control electronics ensure
reliable, linear operation.
• Supported with a full range of mounting and
flying accessories.
• High-power system (138dB Peak SPL @ 1m)
with 15in VLF long excursion driver.
• VLF extension (to 38Hz) of PS10-R2 Loudspeakers.
• Sophisticated control electronics ensure
reliable, linear operation.
• Integral pole mount that supports one or two
PS10-R2 Loudspeakers.
Architectural and Engineering Specifications
LS600-SUB Sub-Bass
Architectural and Engineering Specifications
The 2-way loudspeaker system shall have one 10 inch shielded
Neodymium 8Ω cone transducer and a 1inch compression driver
on a low distortion constant directivity asymmetrical dispersion
horn. The system's horizontal coverage shall range from 50° to
100°, with vertical coverage of +25° and -30°. The user shall be
able to rotate the horn in 4 directions as required by the
application. The system shall have a Q of 16 and a Directivity
Index that is 12 at frequencies above 3kHz. Nominal Sensitivity
shall be 99dB (97dB wideband). When driven by a NXAMP 4x1,
NXAMP 4x4 a PS10 TDController-R2 or by a NX242 properlyconnected to amplification capable of delivering 500 to 1250
Watts into an 8Ω (nominal) load the system shall be capable of
129dB to 132dB peak SPL, with a frequency response of 65Hz to
20kHz ±3dB (58Hz to 21Hz -6dB). The system shall include an
internal passive crossover. Electrical connections shall be made
via one of the two 4-pole NL4MP SPEAKON connectors.
The system shall have a tuned ported multi-angle enclosure
constructed of 18ply Baltic birch, finished in either black or white
textured coating and having exterior dimensions no greater than
515mm H x 316mm W x 277mm D (20.28 inches H x 12.4
inches W x 10.9 inches D): the system shall weigh 14 kg (31lbs).
Exterior hardware shall include 1 metal plate, 2 attachment
points and 1-pole socket. Interior components shall be protected
by a powder coated perforated steel grille. The system shall be
the PS10-R2 with either, a PS10 TDController-R2, NXAMP 4x1,
NXAMP 4x4 or NX242.
A high power system capable of producing 132 dB Peak SPL, the new PS10-R2 Loudspeaker can
be safely driven with up to 1250 Watts of amplifier power. Controlled by the new, dedicated PS10
TDController-R2, or the NXAMP Powered Controller, the PS10-R2 achieves high SPLs and wide
bandwidth performance, despite being only half the weight and volume of common trapezoidal
loudspeaker systems.
Along with the flexible coverage patterns enabled by
NEXO’s proprietary constant directivity asymmetrical
dispersion horn, the architecture and weight balance
of the PS10-R2 are designed to provide both
uncompromised PA and stage monitor performance
from a single speaker. Left and Right versions of the
PS10-R2 have been developed to provide a true
stereo image – particularly important for wedge
applications. The 2-way passive 8Ω design uses a
single amplifier channel to deliver bi-amped
performance, reducing system cost, size and
complexity, while the new cabinet design incorporates
a pole mount and a new hardware adapter compatible
with a vast array of touring and fixed installation
accessories.
System Applications
12
The PS10 TDController-R2’s integral sub section and combined signal (PS10-R2 and LS600) Speakon
wiring ensure cost effective and simple system implementation. One LS600 is typically used with two
PS10-R2 loudspeakers, additional units may be used for an enhanced effect.
The system shall have a tuned ported rectangular enclosure
constructed of 18ply Baltic birch, finished in either black or
white textured coating and having exterior dimensions no
greater than 435mm H x 688mm W x 528mm D (16.9in H x
27.1in W x 20.8in D): the system shall weigh 30 kg (66lbs).
Exterior hardware shall include 1 metal plate, 2 attachment
points and 1-pole socket. Interior components shall be protected
by a powder coated perforated steel grille. The system shall be
the NEXO LS 600 with the PS10 TDController-R2, NXAMP 4x1,
NXAMP 4x4 or NX242.
PS10-R2 horizontal coverage, +25°
LS600 response
LS600 impedance
PS10-R2 + LS600 response
PS10-R2 + LS600 impedance
PS10-R2 horizontal coverage, 0°
• Touring, installed PA for clubs, A/V, theatre,
broadcast, Houses of Worship, etc. High-quality
stage monitoring for cabarets A/V, theatre,
broadcast, etc.
• Fill-in system for use with larger NEXO
PS/Alpha systems, or any application needing
exceptional side, down and near-field
augmentation.
A high power system capable of producing 138 dB Peak SPL, the new LS600 Sub-Bass extends
the usable range of the PS10-R2 Loudspeaker to 38Hz, providing exceptional performance and
high power output in an extremely compact, light weight package.
The sub-bass loudspeaker system shall have one 15 inch
shielded Neodymium 8Ω long excursion cone transducer.
Nominal Sensitivity shall be 101dB. When driven by a NEXO
NXAMP 4x1, NXAMP 4x4 a PS10 TDController-R2 or by a NX242
properly-connected to amplification capable of delivering 1000 to
2000 Watts into a 4Ω (nominal) load the system shall be capable
of 135dB to 138dB peak SPL, with a frequency response of 40Hz
to 110Hz ±3dB (38Hz to 120kHz -6dB). The system shall include
an active crossover. Electrical connections shall be made via one
of two 4-pole NL4MP SPEAKON connectors.
PS10-R2 horizontal coverage, -25°
13
NEXO PS R2 Series Systems - PS10-R2
PS10-R2 Loudspeaker Specifications
LS600-SUB Sub-Bass Specifications
PS10 TDController-R2 Specifications
Product Features
Components
Product Features
Components
Product Features
Audio Inputs
Height x Width x Depth
Weight
Connectors
Construction Baltic
Fittings
Front finish
Flying Points
Stand fittings
PS10 TDController-R2
The PS10 TDController-R2 is an advanced analogue processor that allows the PS10-R2
Loudspeaker and optional LS600 Subwoofer to achieve exceptional performance from such
compact packages. The PS10 TDController-R2 provides crossover, sensed amplifier control and
system equalisation optimised for the PS10-R2 and LS600. One PS10 TDController-R2 has two
inputs and three outputs, L, R and summed sub out, minimising installation cost and complexity.
Key Features
• Precision circuits engineered for the
PS10-R2/LS600 systems permit increased
sound pressure and operational reliability.
• Servo-controlled VCEQs provide precise
dynamic control without spectral imbalance.
• Two inputs and three outputs enable a single
PS10 TDController-R2 to manage multiple
PS10-R2 and LS600 products.
• Comprehensive indicators and controls.
Like all NEXO processors, the PS10 TDController-R2 provides precision dynamic, voice coil temperature
and diaphragm displacement protection through the use of selective Voltage Controlled Equalisers
(VCEQs), reducing levels only at frequencies when and where necessary.
System Specifications PS10-R2 with PS10 TDController-R2
Frequency Response [a]
65 Hz - 20 kHz ±3dB
Usable Range @-6dB [a]
58 Hz - 21 kHz
Sensitivity 1W @ 1m [b]
99 dB SPL Nominal – 97 dB SPL
Wideband
Nominal Peak SPL @ 1m [b] 129 to 132 dB Peak
HF Dispersion [c]
50° to 100° Hor. x 55° Vert. Rotatable
Horn, 4 positions
Q : 16 Nominal DI : 12 dB Nominal
Directivity Q & DI [c]
( f > 3 kHz )
Crossover Frequencies
2 kHz Passive
Nominal Impedance
8Ω
Recommended Amplifiers
500 to 1250 W / 8 Ω
The PS10 TDcontroller R2 shall be configurable from a combination of 2x inputs and 3x outputs with each output providing crossover, parametric EQ,
adjustable peak limiter and Temperature & Displacement protection for NEXO PS10-R2 and LS600 products. The unit shall have electronically
balanced analogue inputs and outputs. All crossover, protection parameters, and EQ are factory optimized and can't be user-accessed. The controller
must model the loudspeakers in real time and this modeling shall include loudspeaker temperature and displacement. Protection shall be selective,
acoustically transparent and not allow PS10-R2 loudspeakers to exceed speaker-dependent thresholds. The device shall have 3x inputs providing
feedback from amplifier output to allow real time monitoring of amplifier voltage. Crossover function between PS10-R2 loudspeakers and the LS600
Subwoofer shall be controlled by the PS10 TDcontroller. Maximum input shall be 22dBu with CMRR 90dB@1kHz and noise floor below -100dB for
the 0dB rear-panel switch. A 3-position, rear-panel gain control switch shall be adjustable between -6/0/+6dB. The Output Section shall display
+22/+16/+10dBm into 600Ω load with Rear Panel switch on +6/0/-6dB (respectively). LEDs shall indicate status for; Power ON (green), Amp
Sense & Peak LED's (green/Red), Temperature & Displacement (yellow) and LS600 (VLF) displacement protection (also yellow). The chassis shall be
constructed of steel with a black paint finish. Input power shall range from 110 to 220VAC continuously, 50-60Hz with a rear panel earth-lift. The
1RU controller shall weigh 2.9kg(6.4lbs), with exterior dimensions of 483mmW x 44mmH x 190mmD (19" x 1.75" x 7.5"). The chassis shall be
constructed of steel with a black paint finish. The controller shall be the NEXO PS10 TDcontroller R2. The unit shall be UL approved and comply with
electrical international standard (CB scheme) based upon the European standard EI60065. The unit shall fulfill the electromagnetic requirement of
the harmonized standards EN55013, EN55020 and of the requirement of the FCC PART 15 CLASS b regulation. Other integrated loudspeakercontrollers shall be acceptable, provided independent laboratory test results verify these specifications are equaled or exceeded.
Height x Width x Depth
Weight
Connectors
Construction
Fittings
Flying Points
Stand fittings
LF 1 x 15" (38cm) long excursion
Neodymium 8Ω driver
435mm x 688mm x 528 mm
(17.12" x 27.09" x 20.79")
30 kg (66 Lbs)
2 x NL4MP Speakon 4 pole
Baltic Birch Ply & textured
black coating
Handles 2 Metal recessed pockets
One plate connecting with external
accessories
Internal Steel Stand Fitting on Top
(35mm, 1 3/8") allows pole mounting
for 1 PS10-R2
System Specifications LS600 with PS10 TDController-R2
Frequency Response [a]
40 Hz - 110 Hz ±3dB
38Hz - 120 Hz
Usable Range @-6dB [a]
101 dB SPL Nominal
Sensitivity 1W @ 1m [b]
Nominal Peak SPL @ 1m [b] 135 to 138 dB Peak
Crossover Frequencies
120 Hz Active through PS10
TDController-R2
8Ω
Nominal Impedance
1000 to 2000W / 8Ω
Recommended Amplifiers
Sense Inputs
Audio Outputs
Controls
Indicators
Dimensions
Weight
Power Supply
Dimensions & Weight
Specifications
Input Level
Output Level
Noise
THD+N
Power Supply
System Operation
Electronic Controller
Architectural and Engineering Specifications
1 x 10" (25cm) Shielded Neodymium
8Ω driver
HF 1 x 1" throat driver + Low Distortion
Constant Directivity Asymmetrical
Dispersion Horn.
515mm x 316mm x 277 mm
(20.28" x 12.44" x 10.91")
14 kg (31 lbs)
2 x NL4MP Speakon 4 pole
Baltic Birch Ply finished with textured
black coating
2 Metal recessed pockets
Moulded Dark Grey Metal Grill
One plate connecting with external
accessories
Built in Steel Stand Fitting, (35mm
1 3/8")
Dispersion configuration
Sub-bass
Speaker Cables
Two L&R Audio inputs. Electronically
balanced, 36 kOhm. Two XLR-3F
connectors.
Three Amplifier Sense Inputs (PS10-R2
L&R, LS600). 150 kOhm. 6 Pole
Removable Strip Terminal.
Two L&R PS10 Audio outputs.
Electronically balanced, 50 Ohm.
Two XLR-3M.
One Mono (L+R) LS600 Audio output.
Electronically balanced, 50 Ohm.
One XLR-3M.
Std/Max Protection Trimmer. Gain switch
(back panel), 3 positions for Amps with
Gain : -6 / 0 / +6 dB.
Sub On switch & Sub Gain Control.
Speaker Protect LEDs. Amp Sense &
Peak LEDs.
1U 19” Rack. 190mm (7.5”) Depth
2.9 kg (6.6 lbs) net
110/220 Volts (internal wiring), 50/60Hz.
Earth-Lift (back panel)
1U 19" Rack. 190mm (7.5") Depth.
2.9 kg (6.6 lbs) net
+28dBm max into 600ohm.
+20 dBm Max. +19dBm Max on
1kOhm
-88 dBm (22 Hz - 22 kHz, UnWeighted)
< 0.03% Typ. 0.05 Max for +18dBm
Output
110/220 Volts (internal wiring), 50/60Hz.
Earth-Lift (back panel)
The PS10 TDController-R2 is precisely matched to the PS10-R2 & LS600 cabinets and includes sophisticated protection systems. Using PS10-R2 & LS600 without a properly connected PS10
TDController-R2 will result in poor sound quality and can damage the components.
After dismounting front grill from its fixings, the HF Horn can be rotated in 4 positions for dispersion configuration.
The PS10-R2 can be used without optional LS600 Sub-Bass. Active two-way operation with the LS600 is included in the PS10 TDController-R2. One LS600 matches 2 x PS10-R2, additional LS600
may be used for enhanced LF capability.
PS10-R2 are wired 2- & 2+ on Speakon connectors, LS600 on 1- & 1+. Loop through Speakons are present on both. Single identical cables can thus be used to loop through combinations of up to
2 x PS10-R2 & 1 x LS600 in no particular order.
As part of a policy of continual improvement, NEXO reserves the right to change specifications without notice.
[a] Response curves & data : Anechoic Far Field for the PS10-R2 + PS10TDController-R2. Half-Space Anechoic radiation for the LS600 + PS10 TDController-R2.
[b] Sensitivity & Peak SPL data : these will depend on spectral distribution and crest factor of program material. Measured with band limited Pink Noise.
Nominal refers to Voice Decade (300 Hz - 3 kHz), Wideband to the specified ±3dB range. Data are for speaker + processor + recommended amplifier combinations.
Peak SPL is at clipping of recommended amplifier.
[c] Directivity curves & data : obtained by computer treatment on off axis response curves.
E&OE September 2009.
System configurations
MONO
PS10-R2/LS600 with NXAMP 4x1
14
STEREO
PS10-R2/LS600 with PS10 TDController-R2
15
NEXO PS R2 Series Systems - PS15-R2
PS15-R2 Loudspeaker
Key Features
RS15-SUB Sub-Bass
Key Features
• High-power system (136dB Peak SPL @ 1m)
with 15in LF and 2in HF drivers.
• Rotatable asymmetrical horn and unique
cabinet architecture ensure versatility; useradaptable for both PA and stage monitoring
applications.
• Two-way, switchable passive or active design
for precise performance-matching to user
requirements.
• Sophisticated control electronics ensure
reliable, linear operation.
• Supported with a full range of mounting and
flying accessories.
• Low profile, high output, modular scalable bass.
• Configurable directivity pattern.
• Cardioid pattern reduces rear levels by
minimizing rear/side wall reflections.
• Aerodynamic profiled vents with 20db noise
reduction and improved linearity at high SPL.
• Applies across entire NEXO product line.
Architectural and Engineering Specifications
RS15-SUB Sub-Bass
Architectural and Engineering Specifications
The 2-way loudspeaker system shall have one 15 inch shielded
Neodymium 8Ω cone transducer and a 2 inch compression
driver on a low distortion constant directivity asymmetrical
dispersion horn. The system's horizontal coverage shall range
from 50° to 100°, with vertical coverage of +25° and -30°.
The user shall be able to rotate the horn in 4 directions as
required by the application. The system shall have a Q of 16 and
a Directivity Index that is 12 at frequencies above 1.5kHz.
Nominal Sensitivity shall be 102dB (99dB wideband). When
driven by a NEXO NXAMP 4x1, NXAMP 4x4 a PS15 TDControllerR2 or by a NX242 properly connected to amplification capable of
delivering 1000 to 2000 Watts into an 8Ω (nominal) load the
system shall be capable of 133dB to 136dB peak SPL, with a
frequency response of 50Hz to 18kHz ±3dB (47Hz to 18Hz 6dB). The system shall include an active or passive crossover
with internal switching. Electrical connections shall be made via
one of the two 4-pole NL4MP SPEAKON connectors.
The system shall have a tuned ported multi-angle enclosure
constructed of 18ply Baltic birch, finished in either black or white
textured coating and having exterior dimensions no greater than
675mm H x 434mm W x 368mm D (26.6in H x 17.1in W x
14.5in D): the system shall weigh 29.0kg (65.0lbs). Exterior
hardware shall include 1 metal plate, 2 attachment points and 1pole socket. Interior components shall be protected by a powder
coated perforated steel grille. The system shall be the NEXO
PS15 R2 with a PS15 TDController-R2, NXAMP 4x1, NXAMP 4x4
or NX242.
A high power system capable of producing 136dB Peak SPL, the new PS15-R2 Loudspeaker can
be safely driven with up to 2000 Watts of amplifier power. Controlled by the new, dedicated PS 15
TDController-R2, or the NXAMP Powered Controller, the PS15-R2 achieves high SPLs and wide
bandwidth performance, despite being only half the weight and volume of common trapezoidal
loudspeaker systems.
Along with the flexible coverage patterns enabled
by NEXO’s proprietary constant directivity
asymmetrical dispersion horn, the architecture
and weight balance of the PS15-R2 are designed
to provide both uncompromised PA and stage
monitor performance from a single speaker.
Left and Right versions of the PS15-R2 have been
developed to provide a true stereo image –
particularly important for wedge applications.
The 2-way passive 8Ω design uses a single
amplifier channel to deliver bi-amped
performance, reducing system cost, size and
complexity, while the new cabinet design
incorporates a pole mount and a new hardware
adapter compatible with a vast array of touring
and fixed installation accessories.
PS15-R2 horizontal coverage, +25°
Extending the usable range of the PS15-R2 Loudspeaker to 35Hz, the RS15 is the first offering of
NEXO’s patent pending RAY SUB Technology. The RAY SUB Technology is based on optimizing
positioning and phase relationships of radiating surfaces in vented enclosures, permitting acoustic
distance from rear to front sections to always increase as frequency decreases; consequently rear
and front sections sum up efficiently over the entire subwoofer bandwidth, allowing for an average
of 5db gain from the rear section in the forward direction and cancelling in the rear direction.
Utilized in a stand alone format, RAY SUB Technology, allows the same cabinet to be configured for any
polar pattern, omni-directional as a standard direct radiating subwoofer when speakers are facing the
audience, or highly directional when a speaker cabinet is rotated sideways or upwards. With arrays, RAY
SUB subwoofers can be set back to back, front to front, alternate, in vertical columns, and when column
length is sufficient be beam-steered upwards or downwards. Comprised of a 15 inch transducer with a
frequency response of 35Hz – 200Hz in omni or 35Hz- 150Hz in directional mode and a sensitivity of
105db SPL, the RS15 presents an unchallenged versatility for installations and touring requirements.
The sub-bass loudspeaker system shall have two 15inch long
excursion 8Ω cone transducers. Nominal Sensitivity shall be
105dB. When driven by a NXAMP 4x1, NXAMP 4x4 a PS15
TDController- R2 or by a NX242 properly-connected to
amplification capable of delivering 2x700 to 2x1200 Watts into a
8Ω (nominal) load the system shall be capable of 136dB to
139dB peak SPL, with a frequency response of 35Hz to 100Hz
±3dB (35Hz to 250kHz -6dB). The system shall include an
active crossover. Electrical connections shall be made via two
4-pole NL4MP SPEAKON connectors.
The system shall have a tuned ported rectangular enclosure
constructed of 18ply Baltic birch, finished in either black or
white textured coating and having exterior dimensions no
greater than 454mm H x 564mm W x 1074mm D (17.9in H x
22.2in W x 42.3in D): the system shall weigh 52.0kg (116lbs).
Exterior hardware shall include 1- pole socket. Interior
components shall be protected by a powder coated perforated
steel grille. The system shall be the RS15 with a PS15
TDController-R2, NXAMP 4x1, NXAMP 4x4 or NX242.
PS15-R2 horizontal coverage, 0°
System Applications
RS15 response
RS15 impedance
PS15-R2 + RS15 response
PS15-R2 + RS15 impedance
• High-power mid-sized touring, installed PA for
clubs, A/V, theater, Houses of Worship,
broadcast, etc.
• High-quality, extremely powerful stage monitoring
for A/V, theatre, cabarets, broadcast, etc.
• Fill-in system for any PA requiring side, down
and near-field augmentation.
16
PS15-R2 horizontal coverage, -25°
17
NEXO PS R2 Series Systems - PS15-R2
PS15 TDController-R2
The PS15 TDController-R2is an advanced analogue processor that allows the PS15-R2
Loudspeaker and optional RS15 Subwoofer to achieve exceptional performance from such
compact packages. The PS15 TDController-R2 provides crossover, sensed amplifier control and
system equalisation optimised for the PS15-R2 and RS15.
Key Features
• Precision circuits engineered for the
PS15-R2/RS15 systems permit increased
sound pressure and operational reliability.
• Servo controlled VCEQs provide precise dynamic
control without spectral imbalance.
• Two inputs and three outputs enable a single
PS15 TDController-R2 to manage multiple
PS15-R2 and RS15 products.
• User configurable for passive or active (bi-amp)
operation of the PS15-R2 Loudspeaker.
• Comprehensive indicators and controls.
The PS15 TDController-R2 also features user-selectable passive or active (bi-amp) operation of the PS15R2 Loudspeaker. One PS15 TDController-R2 has two inputs and three outputs, including summed sub out,
minimising installation cost and complexity.
Like all NEXO processors, the PS15 TDController-R2 provides precision dynamic, voice coil temperature
and diaphragm displacement protection through the use of selective Voltage Controlled Equalisers
(VCEQs), reducing levels only at frequencies when and where necessary.
Architectural and Engineering Specifications
The 1RU PS15 TDcontroller R2 shall be configurable from a combination of 2x inputs and 3x outputs with each output providing crossover, parametric EQ,
and mid-filter limiters for NEXO PS15-R2 products. The unit shall have electronically balanced analogue inputs and outputs. Each input must provide LF
shelving filter to compensate ground or stacking effects, ±6dB LEVEL TRIM controls for each output must be independent and directly accessible through
front-panel potentiometers. All crossover, protection parameters, and EQ are factory optimized and can’t be user-accessed. The controller must model the
loudspeakers in real time and this modeling shall include loudspeaker temperature and displacement. Protection shall be selective, acoustically transparent
and not allow PS15-R2 loudspeakers to exceed speaker-dependent thresholds. The controller shall have 3x inputs providing feedback from amplifier output
to allow real time protections on real voltage. The device shall change between passive and active switching through internal jumper connections. Maximum
input shall be 22dBu with CMRR 90dB@1kHz and THD+N 0.05%@1kHz at +18dBm output. A 3-position, rear panel gain control switch shall be adjustable
between -6/0/+6dB. The Output Section shall display +28/+22/+16dBm into 600Ω load with Rear Panel switch on +6/0/-6dB (respectively). LEDs shall
indicate status for; Power ON (green), Amp-Sense & Peak LED's (green/Red), Temperature & Displacement (yellow) and RS15 (VLF) displacement protection
(also yellow). The unit shall have the following front panel controls: Overlap/Crossover Switch; 2x Bass EQ trimmers; 3x Peak Limiter Adjust trimmers; 3x Gain
trimmers, and the following LED indicators: Power On; Active Mode; Amp-Sense; Amp Peak; Speaker Protect. The unit's rear panel shall have the following
controls: 3-position Amp Gain switch; Active/Passive mode switch; 3x Protection trimmers; Earth Lift. The 1RU device shall weigh 3.3kg(7.3lbs), be steelconstructed, with a blue paint finish and exterior dimensions of 483mmW, 44mmH and 210mmD (19" x 1.75" x 8.5"). Input power shall be 110/220VAC,
50-60Hz. The analog loudspeaker management controller shall be the NEXO PS15 TDcontrollerr R2. The unit shall be UL approved and comply with electrical
international standard (CB scheme) based upon the European standard EI60065. The unit shall fulfill the electromagnetic requirement of the harmonized
standards EN55013, EN55020 and of the requirement of the FCC PART 15 CLASS b regulation. Other analog loudspeaker management controllers shall be
acceptable, provided independent laboratory test results verify these specifications are equaled or exceeded.
PS15-R2 Loudspeaker Specifications
RS15-SUB Sub-Bass Specifications
PS15 TDController-R2 Specifications
Product Features
Components
Product Features
Components
Product Features
Audio Inputs
LF 1 x 15" (38 cm) long excursion
Neodymium 8Ω driver
HF 1 x 2" throat, 3" Titanium diaphragm,
driver + Low Distortion, Constant
Directivity Asymmetrical Dispersion Horn.
675mm x 434mm x 368 mm
Height x Width x Depth
(26.57" x 17.08" x 14.48")
Weight
28 kg (62 lbs.)
2x4 pole in & loop thru (switch
Speakon Connectors
passive to active inside).
Construction
Baltic Birch Ply finished with textured
black coating
Handles 2 Metal recessed pockets
Fittings
Front finish
Moulded Dark Grey Metal Grill
Flying Points
Two plate connecting with external
accessories
Stand fittings
Built in Steel Stand Fitting, (35mm
1 3/8")
System Specifications PS15-R2 with PS15 TDController-R2
50 Hz - 18 kHz ±3 dB
Frequency Response [a]
Usable Range @-6dB [a]
47 Hz - 18 kHz
Sensitivity 1W @ 1m [b]
102 dB SPL Nominal.
99 dB SPL Wideband
Nominal Peak SPL @ 1m [b] 133 to 136 dB Peak
HF Dispersion [c]
50° to 100° Hor. x 55° Vert. Rotatable
Horn - 4 positions
Q : 16 Nominal DI : 12 dB Nominal
Directivity Q & DI [c]
( f > 1.5 kHz )
Crossover Frequencies
1.1 kHz Passive or Active (internally
switchable)
Nominal Impedance
Passive : 8Ω or Active : LF : 8Ω &
HF : 16Ω Important: Active Mode only
available on NXAMP
Recommended Amplifiers
Passive: 1000 to 2000 W / 8Ω
Active: (LF) 1000 to 2000 W / 8Ω (HF) 250 to 500 W / 16Ω Important:
Active Mode only available on NXAMP
System Operation
Electronic Controller
Dispersion configuration
Sub-bass
Speaker Cables
2 x 15" (38cm) long excursion
Neodymium 8Ω drivers
454mm x 564mm x 1074 mm
Height x Width x Depth
(17.9"x 22.2"x 42.3")
52 kg (116 lbs)
Weight
2 x 4 pole (In & Loop Thru)
Speakon Connectors
Construction
Baltic Birch Ply & textured black coating
Dark Grey Carpet also available
RS15 with NX242, NXAMP or PS15 TDController-R2
System Specifications (Omni)
35 Hz - 100 Hz
Frequency Response
@ -3db [a]
Usable Range @ -6db [a]
35 Hz - 250 Hz
105 dB SPL Nominal
Sensitivity 1W @ 1m [b]
136 to 139 dB Peak
Nominal Peak SPL @ 1m [b]
Crossover Frequencies
80 Hz - 200 Hz (Controller dependant)
Nominal Impedance
2 x 8Ω
2 x 700W to 2 x 1200W / 8Ω
Recommended Amplifiers
RS15 with NX242-ES4 or NXAMP
System Specifications (Directional)
Frequency Response
35 Hz - 100 Hz
@ -3db [a]
Usable Range @ -6db [a]
35 Hz - 150 Hz
Sensitivity 1W @ 1m [b]
103 dB SPL Nominal
133 to 136 dB Peak
Nominal Peak SPL @ 1m [b]
80 Hz - 125 Hz (Controller dependant)
Crossover Frequencies
Nominal Impedance
2 x 8Ω
Recommended Amplifiers
2 x 700W to 2 x 1200W / 8Ω
Sense Inputs
Audio Outputs
Controls
Indicators
Dimensions
Weight
Power Supply
Dimensions & Weight
Specifications
Input Level
Output Level
Noise
THD+N
Power Supply
Two L&R Audio inputs. Electronically
balanced, 50KOhm. Two XLR-3F
connectors.
Three Amplifier Sense Inputs, 180
kOhm. 6 Pole Removable Strip Terminal.
Passive Mode, PS15 L&R, LS1200).
Active Mode, PS15 LF and HF, LS1200.
Three audio outputs. Electronically
balanced, 50 Ohm. Three XLR-3M
connectors.
Passive Mode, two PS15-R2 L&R, one
Mono (L+R) RS15. Active Mode, one
PS15-R2 LF, one PS15HF, one Mono
(L+R) RS15
Front panel: Overlap/Crossover switch,
Two Bass EQ trimmers (+/- 3 dB), Three
Peak Limiter Adjust trimmers. Three Gain
trimmers (+/- 6dB). Back panel: Gain
switch (back panel), 3 positions for Amps
with Gain : -6 / 0 / +6 dB. Internal:
Active/Passive Mode switch. Three
Protection trimmers.
Speaker Protect LEDs. Amp Sense &
Peak LEDs. Active Mode LED. Power ON
LED.
1U 19" Rack. 210mm (8.5”) Depth
3.3 kg (7.3 lbs) net
110/220 Volts (internal wiring), 50/60Hz.
Earth-Lift (back panel)
1U 19" Rack. 190mm (7.5") Depth.
2.9 kg (6.6 lbs) net
+28dBm max into 600ohm
+22dBm
-88 dBm (22 Hz - 22 kHz, UnWeighted)
< 0.03% Typ. 0.05 Max for +18dBm
Output
110/220 Volts (External Rear Panel
Switch), 50/60Hz. Earth-Lift (back panel)
The PS15TD Controller-R2 is precisely matched to the PS15-R2 & RS15 cabinets and includes protections. Using PS15-R2 & RS15 without a properly connected PS15 TDController-R2 will result in
poor sound quality and can damage the components.
After dismounting the front grille from its fixings, the HF Horn can be rotated in 4 positions for dispersion configuration.
The PS15-R2 can be used without optional RS15 Sub-bass. Active two-way operation with RS15 is included in the PS15 TDController-R2. One RS15 matches 2 x PS15-R2, additional RS15 may be
used for enhanced LF capability.
PS15R2 are wired 2-/2+ on Input Speakons in Passive Mode. PS1R25 are wired LF 1-/1+ & HF 2-/2° on Input Speakons in Active Mode. Please refer to RS15 User Manual for RS15 for RS15 connection.
As part of a policy of continual improvement, NEXO reserves the right to change specifications without notice.
[a] Response curves & data : Anechoic Far Field for the PS15-R2 + PS15TDController-R2. Half-Space Anechoic radiation for the RS15R2 + PS15TDController-R2.
[b] Sensitivity & Peak SPL data : these will depend on spectral distribution and crest factor of program material. Measured with band limited Pink Noise.
Nominal refers to Voice Decade (300 Hz - 3 kHz), Wideband to the specified ±3 dB range. Data are for speaker + processor + recommended amplifier combinations.
Peak SPL is at clipping of recommended amplifier. Measurements made with PS15-R2s in passive operation mode.
[c] Directivity curves & data : obtained by computer treatment on off axis response curves.
E&OE September 2009.
System configurations
MONO
PS15-R2/RS15 with NXAMP 4x4
18
STEREO
PS15-R2/RS15 with PS15 TDController-R2
19
NEXO PS R2 Series Systems
Installation
Mounting accessories
The PS R2 Series is supported by a comprehensive range of TUV certified
mounting accessories designed to make it quick and easy to set up PS R2
Series systems in both mobile and fixed installations.
Sound contractors know that time is money, so PS R2 Series touring
hardware draws on 30 years of NEXO experience to ensure maximum
security and flexibility with minimum rigging time.
All PS R2 Series speakers ship with 35mm/1 3/8" pole mounts on the bottom
of the cabinets for positioning on a general purpose speaker stand or mast
inserted in top-fitted stand adapters on the sub-bass
cabinets, while the PS10-R2 and PS15-R2 both feature
steel anchor plates on the top for direct mounting onto a
range of hanging and flying accessories (an adaptor plate
is available for the PS8).
For outdoor installations, IP boxes are available giving
full compliance with IP54 rating for protection from the
harmful ingress of water.
SSBRK10
U-Bracket for PS10-R2
UBRK10 U-Bracket for PS10-R2
ABRK
Horizontal mounting plate for
PS10-R2 & PS15-R2
UBRK12 U-Bracket for PS15-R2
IPCOV8 IP Box for
PS8 & PS10-R2
WS-10 Fixed hanging
bracket for PS8 & PS10-R2
IPCOV15 IP Box for
PS15-R2
WS-15 Fixed hanging
bracket for PS15-R2
UBRK8 U-Bracket for PS8
ADPT510 Hardware adapter for PS8
PS R2 Series
Loudspeakers are also
available in white.
Touring
SSBRK8
U-Bracket for PS8
(includes ADPT adapter)
LBRK
Long mounting plate for
PS10-R2 & PS15-R2
ADPT Hardware adapter for PS8
TTC Truss clamp bracket
XHBRK Lifting ring
TCBRK Truss hook
SSBRK15 U-Bracket for PS15-R2
20
21
NEXO PS R2 Series Systems
NXAMPS - 4x1 and 4x4 Powered TDControllers
NEXO NXAMP 4x1 and 4x4 Powered TDControllers integrate loudspeaker and
amplifier control into a single device to provide PS R2 series users with a flexible,
high-output amplification solution, with instant access to NXStream, Monitor and
Standard presets (PS10-R2/PS-15R2). Alongside all the control parameters
necessary to optimise loudspeaker performance, the NXAMPs also enable the user
to manage the voltage/current/sense lines from the output, protecting both the
amplifier and its power supply in real time.
Two 4-channel models with output capacities of 4x1300W under 2Ω (4x1) and
4x4000W under 2Ω (4x4) establish the NXAMP 4x1 as one of the most versatile
amplifiers in the business, and the NXAMP 4x4 as one of the most powerful
amplifiers ever produced.
Capable of powering multiple PS R2 Series loudspeakers, the
versatility of the NXAMPs can be enhanced yet further with optional
EtherSound 100 hardware.
NAXMP Specifications
Key Features
• Delivers cost-effective integration of amplifier
and loudspeaker control
• Choice of 4x1300W and 4x4000W models
• Capable of powering multiple PS R2 Series
loudspeakers
• Lighter and requires less rack space than
conventional amplifier/processing systems
• Eliminates unnecessary A/D conversion
• Utilizes Yamaha EEEngine technology to deliver
maximum efficiency in driver performance and
power, with uncompromised sonic performance
• Optional EtherSound networking
NX242 TDController
NEXO’s NX242 TDController is an advanced,
proprietary digital processor that maintains
exceptional performance and reliability in PS
loudspeaker systems and associated SubBasses. The NX242 provides crossover,
sensed-amplifier control and system
alignment acoustically matched to each
NEXO component.
Power Specifications for NXAMP4x1
Number of amplifiers channels 4x channels, 2 by 2 bridgeable
Max. output voltage (no load) 4 x 105Volts
Max. output power (8Ω)
4 x 600W
Max. output power (4Ω)
4 x 900W
Max. output power (2Ω)
4 x 1300W
Power consumption (Standby) 10W
Power consumption (Idle)
100W
Power consumption (1/8 Power) 1100W
Power Specifications for NXAMP4x4
Number of amplifiers channels 4x channels, 2 by 2 bridgeable
Max. output voltage (no load) 4 x 200Volts
Max. output power (8Ω)
4 x 1900W
Max. output power (4Ω)
4 x 3300W
Max. output power (2Ω)
4 x 4000W
Power consumption (Standby) 20W
Power consumption (Idle)
150W
Power consumption (1/8 Power) 3000W
Common NXAMP Specifications from Analogue In to Power Out
Analogue Inputs channels
4x channels, analogue inputs on XLR 3
with a second XLR 3 for linking
Frequency response
±0.5dB from 10Hz to 20KHz
Input Impedance
20KΩ
Max Input Level
+28dBu
Dynamic Range
All Channels = 105dB unweighted
THD + Noise
Typical 0.1% flat setup
Latency time
500us on a flat setup
Power Supply
Dedicated version for 100 ~ 120Volts or
220 ~ 240Volts
Common NXAMP Features
Audio Inputs
4x balanced analogue inputs on XLR3
with a second XLR3 for linking, using
24bit converters.
4x digital inputs via the optional network
card slot at the back.
Power Outputs
4x Speakon outputs using internal power
relay for automatic output assignment
regarding setup.
RS232 port
Allow firmware upgrade for software
improvement and new cabinet setups.
GPIO port
5x Global Purpose Inputs and 8x Global
Purpose Outputs for simple remote
control and monitoring.
Processing
Two DSPs, 24bit data with 48bit
accumulator. 700MIPS.
Front Panel
Rear Panel
Dimensions & Weight
NXAMP User Controls
System Selection
System Set-up
Protection
Delay
Input Patching
Output Gain
Volume control
Save/Recall
Array EQ
Security Mode
Remote control
Certification
Green status
On/Off Mains switch, Select Wheel, Menu
A and Menu B buttons, 40 characters by
2 lines display. Amp protect, Stand-by
and power LED’s. Then for each channel:
volume indicator (15x LEDs), Individual
Mute buttons and red LED, output current
signal green led, Speaker Protection
yellow LED, Amp. Peak red LED.
1 (NXAMP4x1) or 2 (NXAMP4x4) mains
socket; RS232 serial communications
connector; GPIO port, Expansion slot for
networking audio extension card, 4 XLR
inputs with link and 4 Speakon 4 outputs.
NXAMP4x1: 3U 19” Rack - 457 mm
(18”) Depth - 16.5kg (33lbs) net
NXAMP4x4: 4U 19” Rack - 457 mm
(18”) Depth - 24.5kg (49lbs) net
Allows control across all NEXO ranges.
Within the selected range, if possible,
allows cabinets to be set for passive or
active mode, wideband or crossover
mode, choose among available crossover
point, cardioid or supercardioid mode.
Multiple Peak Limiters fitted for both
selected cabinet and amplifier. Multiple
Acceleration, Displacement and
Temperature protections on every
channel. Inter-channel regulation.
Up to 150m (330 ft.) of delay in 10cm
(.4in ) steps
Allows any of the 4x analogue (or digital)
inputs combination to be routed on each
output.
Global and inter-channel gain ±6dB in
0.5dB steps.
Each channel with 16x steps from – inf
dB to 0dB.
Set-up Stores up to 40x user set-ups;
On- the-fly recall, without mute or
glitches for instant comparison.
LF or HF shelving filters to compensate
ground or stacking effects, ±6dB,
frequency factory tuned.
Password protected for Read-Only or
Remote-Only Mode.
Full remote control via the Ethersound
protocol and ESmonitor software.
UL, SEMKO (CE), CCC, KOREA, TSS, PSE
Compliant with ROHS and WEEE directive
As part of a policy of continual improvement, NEXO reserves the right to
change specifications without notice. E&OE September 2009.
22
23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising