ProLinx 6201-WA-DFNT to DFNT Setup guide

6201-WA-ASCII to 6201-WA-DFNT

ProLinx Wireless

High Speed Wireless ASCII Generic Serial Gateway

Setup Guide

9/6/2007

Please Read This Notice

Successful application of this module requires a reasonable working knowledge of the ProLinx

Module, its connected devices, and the application in which the combination is to be used. For this reason, it is important that those responsible for implementation satisfy themselves that the combination will meet the needs of the application without exposing personnel or equipment to unsafe or inappropriate working conditions.

This manual is provided to assist the user. Every attempt has been made to assure that the information provided is accurate and a true reflection of the product's installation requirements. In order to assure a complete understanding of the operation of the product, the user should read all applicable documentation on the operation of the connected devices.

Under no conditions will ProSoft Technology be responsible or liable for indirect or consequential damages resulting from the use or application of the product.

Reproduction of the contents of this manual, in whole or in part, without written permission from

ProSoft Technology is prohibited.

Information in this manual is subject to change without notice and does not represent a commitment on the part of ProSoft Technology Improvements and/or changes in this manual or the product may be made at any time. These changes will be made periodically to correct technical inaccuracies or typographical errors.

Important Installation Instructions

Power, input and output wiring must be in accordance with Class I, Division 2 wiring methods – Article 501-4 (b) of the National Electrical Code, NFPA 70 and in accordance with the authority having jurisdiction. The following warnings must be heeded:

A

B

C

D

WARNING – EXPLOSION HAZARD – SUBSTITUTION OF

COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIV. 2;

WARNING – EXPLOSION HAZARD – WHEN IN HAZARDOUS

LOCATIONS, TURN OFF POWER BEFORE REPLACING OR WIRING

MODULES, and

WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT

EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE

AREA IS KNOWN TO BE NONHAZARDOUS.

"THIS DEVICE SHALL BE POWERED BY CLASS 2 OUTPUTS ONLY."

Your Feedback Please

We always want you to feel that you made the right decision to use our products. If you have suggestions, comments, compliments or complaints about the product, documentation or support, please write or call us.

ProSoft Technology

1675 Chester Avenue, Fourth Floor

Bakersfield, CA 93301

+1 (661) 716-5100

+1 (661) 716-5101 (Fax) http://www.prosoft-technology.com

Copyright © ProSoft Technology, Inc. 2000 - 2007. All Rights Reserved.

6201-WA-ASCII Setup Guide

9/6/2007

PSFT.ASCII.PLX.UM.Thursday, September 06, 2007

ProSoft Technology ®, ProLinx ®, inRAx ®, ProTalk® and RadioLinx ® are Registered Trademarks of ProSoft Technology, Inc.


Contents

PLEASE READ THIS NOTICE .............................................................................................................................. 2

Important Installation Instructions ...................................................................................................................... 2

Your Feedback Please ...................................................................................................................................... 3

CONTENTS ........................................................................................................................................................... 5

1 INTRODUCTION........................................................................................................................................... 7

1.1

Before You Begin..................................................................................................................................... 7

1.2

Using the Sample ProSoft Configuration Builder Files............................................................................. 8

1.3

About Transmission Casts ......................................................................................................................10

2 LOAD THE REQUIRED SOFTWARE..........................................................................................................11

2.1

Install ProSoft Configuration Builder (PCB) ............................................................................................11

2.2

Copy the Sample Application File ...........................................................................................................12

3 CONFIGURE THE ASCII MODULE.............................................................................................................13

3.1

Complete the ProSoft Configuration Builder Sections ............................................................................14

3.1.1

Radio Ethernet Configuration ........................................................................................................14

3.1.2

Radio Configuration.......................................................................................................................15

3.1.3

Radio SNTP Client ........................................................................................................................16

3.1.4

Radio PWP Exchanges .................................................................................................................17

3.1.5

Radio PWP Multicast Group List ...................................................................................................20

3.1.6

ASCII Port 0 ..................................................................................................................................20

3.1.7

Common........................................................................................................................................21

3.2

Save and Download the Configuration File to the 6201-WA-ASCII ........................................................21

4 CONFIGURE THE DFNT MODULE.............................................................................................................23

4.1

Complete the ProSoft Configuration Builder Sections ............................................................................24

4.1.1

Radio Ethernet Configuration ........................................................................................................24

4.1.2

Radio Configuration.......................................................................................................................25

4.1.3

Radio SNTP Client ........................................................................................................................26

4.1.4

Radio PWP Exchanges .................................................................................................................27

4.1.5

Radio PWP Multicast Group List ...................................................................................................29

4.1.6

DFNT Client 0................................................................................................................................29

4.1.7

DFNT Client 0 Commands SLC5002 Address Fields....................................................................30

4.1.8

CommonNet ..................................................................................................................................31

4.2

Save and Download the Configuration File to the 6201-WA-DFNT ........................................................32

5 VERIFY DATA EXCHANGE ........................................................................................................................35

6 DEFAULT MODULE CONFIGURATION ASSIGNMENTS..........................................................................37

6.1

IP Addresses ..........................................................................................................................................37

6.2

WATTCP Parameters .............................................................................................................................37

7 PROSOFT TECHNOLOGY, INC., SUPPORT, SERVICE & WARRANTY ..................................................39

7.1

How to Contact Us: Sales and Support...................................................................................................40

7.2

Return Material Authorization (RMA) Policies and Conditions ................................................................41

7.2.1

All Product Returns .......................................................................................................................41

7.3

Procedures for Return of Units Under Warranty .....................................................................................41

7.4

Procedures for Return of Units Out of Warranty .....................................................................................42

7.4.1

Un-repairable Units .......................................................................................................................42

7.5

LIMITED WARRANTY ............................................................................................................................43

7.5.1

What Is Covered By This Warranty ...............................................................................................43

7.5.2

What Is Not Covered By This Warranty.........................................................................................44

7.5.3

DISCLAIMER REGARDING HIGH RISK ACTIVITIES ..................................................................45

7.5.4

DISCLAIMER OF ALL OTHER WARRANTIES.............................................................................45

7.5.5

LIMITATION OF REMEDIES**......................................................................................................45

ProSoft Technology, Inc.

September 6, 2007

Page 5 of 50

6201-WA-ASCII ♦ ProLinx Wireless


Contents

7.5.6

Time Limit for Bringing Suit ...........................................................................................................45

7.5.7

No Other Warranties .....................................................................................................................46

7.5.8

Intellectual Property ......................................................................................................................46

7.5.9

Additional Restrictions Relating To Software And Other Intellectual Property ..............................46

7.5.10

Allocation of risks ..........................................................................................................................47

7.5.11

Controlling Law and Severability ...................................................................................................47

INDEX ...................................................................................................................................................................49

Page 6 of 50 ProSoft Technology, Inc.

September 6, 2007


1 Introduction

In This Chapter

¾ Before

¾ Using the Sample ProSoft Configuration Builder Files ............. 8

¾ About

This manual is intended to guide you through the setup and configuration of your

ProLinx Wireless ASCII and DFNT devices.

Important: This Setup Guide shows you how to set up a simple wireless network between a 6201-WA-ASCII module and a 6201-WA-DFNT module. This guide should be used as a starting point only.

In all likelihood, the requirements of your particular application will involve additional configuration and development. For detailed information on the ASCII, DFNT, and

ProLinx Wireless protocols, please refer to the following Driver Manuals, on your

ProSoft Solutions CD-ROM:

ASCII Manual

DFNT Manual

PWP Driver Manual

For general information on installing and configuring ProLinx modules, please refer to the ProLinx Reference Guide, also on your ProSoft Solutions CD-ROM.

1.1 Before You Begin

The insert included with your modules describes a sample SINGLE-REMOTE SITE SAMPLE application.

It is important that you read through the insert and perform any required steps.

Setting up the ASCII and DFNT network is relatively simple using the sample files included on the ProLinx

Solutions CD. The flow diagram illustrates the highlevel steps used to configure each module.

The default configuration file contains separate configurations for each module. You can use the sample files to get started or you can create the configuration files from scratch. The easiest way to begin is to use the sample configurations. Once you understand how they are created, setting up your network is easy.

Load Required Software to

Your PC or Laptop

Configure the local

6201-WA-ASCII

Configure the remote

6201-WA-DFNT


September 6, 2007

Page 7 of 50

6201-WA-ASCII module ♦ ProLinx Wireless


1.2 Using the Sample ProSoft Configuration Builder Files

Introduction

The sample application uses one 6201-WA-ASCII module and one 6201-WA-

DFNT module to establish wireless communications between an ASCII

Communication Device (Terminal, Scanner, Printer) at a local site and a PLC located at a remote site. The WA-DFNT module is configured as a Client. The following diagram illustrates this application.

Remote Site

Local Site

12

00 W or ds ord s

12

00 W

24

00

Ch ar ac te rs ac te rs

24

00

Char

6201- WA- DFNT

( Client)

EtherNet/IP

Ethernet

ControlLogix

( Server)

ASCII

CommunicationsDevice

Local

6201- WA- ASCII

In this example, the following is assumed:

That the ASCII Device and the Remote PLC are located far enough from each other that a wired connection would be impractical

The application uses one 6201-WA-ASCII module and one 6201-WA-DFNT module to establish communication between the ASCII Device such as a data terminal with modifications to the ASCII module configuration file. Scanners and printers may also be connected.

The module's radio communication parameters are preset and configured to pass up to 1200 words/2400 characters in either direction

You can use this guide in one of two ways. First, you can use it as a learning tool to see how the PCB files make the sample application work. You can also follow along with the example and modify the configuration files as you go along.

The logic in the following flow chart needs to be implemented in the processor to which the 6201-WA-DFNT is wired. This will enable the 6201-WA-ASCII module to properly exchange data with the Serial Port connected ASCII Device.

In the example below, the 6201-WA-6201 Module has been configured to transmit and receive data using "Intercharacter Delay Timeout". This means that when the users set amount of milliseconds expires without arrival of additional characters into serial port buffer, the module will transfer the arrived data from the serial port buffer into the module's main memory. The data in the main memory is available to the radio section of the module for wireless exchange.


September 6, 2007


The gray boxes to the left of the chart give an explanation of logical events in each of the chart symbols.

Legend: (For details refer to Generic ASCII Serial Communications

Module Driver Manual. Sections 2.1.1 and 2.1.2)

RW[X]=V; Received(PLC Input) Word offset position in the array. V is Value.

TW[X]=V; Transmit(PLC Output) Word offset position in the array. V is Value.

RA[0]; Received ASCII data array with 0 as starting position. 127 Words max.

TA[0]; Transmit ASCII data array with 0 as starting position. 127 words max.

START

Monitor for change in the value of the

Received Word array at index 0.

NO

Transfer ASCII data from Received Word array starting at index 3 to ASCII data array starting at index 0. Maximum data array size is 127 words (255 bytes).

Transmit Word outputs at Index:

[0] New incremented integer value.

[1] Character count from last Received Word .

[2] Inter Character spacing in Milliseconds .

[3] Byte quantity of data to transmit.

Transfer ASCII data from Transmit ASCII data array starting at index 0 to transmit Word array starting at index 4. Maximum data array size is

127 words (255 bytes).

TW[0]=V( new)

TW[1]=V(RW[2])

TW[2]=V( mSec)

TW[3]=V( Byte Qty)

YES


September 6, 2007

Page 9 of 50

6201-WA-DFNT ♦ ProLinx Wireless


1.3 About Transmission Casts

Introduction

The sample uses a UNICAST transmission type. UNICAST means that you set up Produce and Consume Commands that transfer or receive data between two individual modules. For example, a Produce command can specify that this data is only produced to one particular consuming module based on the consuming modules IP address.

In addition to UNICAST, you also have the flexibility of using MULTICAST (data sent to multiple modules in a MULTICAST Group List but only picked up by the module within that list with a Consume command that has the matching

Exchange ID and the IP address of the module multicasting the command), and

BROADCAST which sends data out to all modules. With BROADCAST, each module receives the transmission whether it be two modules or 50 modules.

Each module receiving the BROADCAST has to check every message to determine if it is intended for the module or not. This can decrease performance times since the module may be checking hundreds of messages that are not intended for it.

Use MULTICAST to limit the modules that should receive the message. For example, five modules may be part of a MULTICAST Group, yet there may be 15 modules on the network. Only five of the 15 modules on the network will be configured to handle certain types of commands while the remaining 10 that are not in the MULTICAST group will ignore the messages not intended for them.


September 6, 2007

Load the Required Software 6201-WA-DFNT ♦ ProLinx Wireless


2 Load the Required Software

In This Chapter

¾ Install ProSoft Configuration Builder (PCB)............................ 11

¾ Copy the Sample Application File .......................................... 12

There is one application (ProSoft Configuration Builder) and one file (PPF) that you must download from the ProLinx Solutions CD to your PC or LAPTOP whether you are using the sample configuration or are modifying the configuration to suit the needs of your application. This section describes how to get everything you need loaded to your PC. You must perform these steps regardless of whether you are configuring your modules now or just reading about the sample applications.

2.1 Install ProSoft Configuration Builder (PCB)

ProSoft Configuration Builder helps you configure the module for your application.

1 Insert the ProLinx Solutions CD into the CD-ROM drive on your PC or

LAPTOP. The ProLinx Solutions splash page appears:

2 Select Install Configuration Tool.

3 Follow the prompts to install ProSoft Configuration Builder to your hard disk.


September 6, 2007

Page 11 of 50



2.2 Copy the Sample Application File

Load the Required Software

4 From the ProLinx Solutions splash screen, click Product

Documentation .

5 Choose Samples → Wireless.

6 Copy the PROLINX WIRELESS SAMPLE.PPF file to a location on your PC or LAPTOP.


September 6, 2007

Configure the ASCII Module 6201-WA-DFNT ♦ ProLinx Wireless


In This Chapter

¾ Complete the ProSoft Configuration Builder Sections............ 14

¾ Save and Download the Configuration File to the 6201-WA-ASCII

............................................................................................... 21

Based on the sample application, the remote Server is connected to a 6201-WA-

DFNT configured as a Client. The goal here is to begin to establish communications between the 6201-WA-ASCII and the 6201-WA-DFNT modules. The default configuration is designed to pass 1200 words between each module. Each module is configured separately.

Configuration is accomplished using ProSoft Configuration Builder (PCB). The default configuration file is PROLINX WIRELESS SAMPLE.PPF.

1 Start PCB.

2

Select File → Open.

3

Navigate to the location where you copied the PROLINX WIRELESS

SAMPLE.PPF

file and select this file.

4

Expand the ASCII Serial to EtherNetIP folder.

5 Expand the 6201-WA-ASCII module selection.


September 6, 2007

Page 13 of 50



Configure the ASCII Module

3.1 Complete the ProSoft Configuration Builder Sections

3.1.1 Radio Ethernet Configuration

Double-click the icon.

Every ASCII module is set up with the defaults shown in the example. You may have to modify values such as the Radio Default Gateway, the Network Name

(SSID), and the Station Name to suit the needs of your network. The Station

Name may be modified when using more than one ASCII module.

Note: All modules must have the same Subnet Mask, Default Gateway, and Network

Name (SSID) if they are all located on the same network. Only the fourth octet in the

Radio_IP address must be different for each module. Please refer to Default Module

Configuration Assignments for a list of pre-assigned ProSoft product IP addresses.

The PWP Driver Manual located on the ProLinx Solutions CD contains a description of the remaining parameters. If you are making changes, be sure to save your changes before moving on to the next step.


September 6, 2007


Expand the Wireless Configuration section


High Speed Wireless ASCII Generic Serial Gateway and double-click on the icon.

The default Signal LED 1 through 4 parameter values are fixed and cannot be modified. If you need to change the values for the remaining parameters in this dialog box, make sure to save your changes before moving on to the next step.

As you select each parameter, the help text area in the lower right area of the dialog box displays information to help you make your selections.

RTS Threshold

60 to 2347

RTS/CTS handshake threshold byte count. Less than 60 will interfere with control packets.


September 6, 2007

Page 15 of 50




Transmit Rate

This parameter defines the data rate(s) for transmission of directed messages.

Possible values are outlined in the following table.

4

5

6

7

Value Definition

1

2

3

Fixed 1 Mbit (1)

Fixed 2 Mbit (2)

Auto fallback high (11, 5.5, 2, 1)

Fixed medium rate (5.5)

Fixed high rate (11)

Auto fallback standard (2, 1)

Auto fallback medium (5.5, 2, 1)

Important: For Multicast mode, use transmit rates of 1 or 2 for best results.

WEP Key Rollover

Yes or No

WEP (Wireless Encryption Protocol) is an encryption method that allows devices on a wireless network to transmit data securely.

This parameter interacts with the WATTCP file parameter "Enable Encryption" and the values for WEP Keys 1 through 4. When the WEP Key Rollover parameter is enabled, the module will randomly change the WEP key.

3.1.3 Radio SNTP Client

Double-click on the icon.


September 6, 2007



This section is used to synchronize the time using a centralized atomic clock.

This feature is only usable if your modules are communicating through an access point such as a RadioLinx Industrial Hotspot. The values in this window should be left with the default values. As you select each parameter, the help window on the screen displays information to help you make your selections. The PWP

Driver Manual located on the ProLinx Solutions CD describes each parameter in detail.

3.1.4 Radio PWP Exchanges


This is the area where you set up data exchange between the modules.

Communication is accomplished using Producer and Consumer commands.

Using these commands, you specify the IP address of the receiving (Consumer) and sending (Producer) module as well as the database locations to produce data and receive data.

In the sample application, the modules are set up to send 1200 words back and forth between the 6201-WA-ASCII and the 6201-WA-DFNT modules. Each module contains a database and both modules are capable of producing or consuming data. This is accomplished using ProSoft Wireless Protocol (PWP) commands. In the sample, we are sending all 1200 words and receiving 1200 words back. We are actually sending only 50 words of data from and to the user's main and remote sites.

Two Produce commands and two Consume commands are used to make this happen. Each command sends (or receives) 600 words of data. The following example shows both produce commands from the sample application.

1 3 4 5 2 6


September 6, 2007

Page 17 of 50



Producer Command Narrative for the First Command (line 1):

1 Send data using Unicast Mode

2

Send the data to IP Address 172.16.10.150.

3

Send 600 registers beginning at DB Register 0.

4

Do not set a Swap Code.

5 Send the data every 100 milliseconds.

6

Use an Exchange ID of 1000.

Producer Command Narrative for the Second Command (line 2):


2 Send the data to IP Address 172.16.10.150.

3 Send 600 registers beginning at DB Register 600.

4 Do not set a Swap Code.


6 Use an Exchange ID of 1001.


Note: IP Address 172.16.10.150 is the 6201-WA-DFNT module.

The Consume commands perform the same function for data coming into the module from the DFNT once configured.

1 3 4 5 2 6

Consumer Command Narrative for the First Command (line 3):

1 Consume data using Unicast Mode.

2 Consume this data only from IP Address 172.16.10.150.

3 Consume 600 words and store them beginning at DB register 1200.

4 Do not use a Swap Code.

5 Consume data within 400 milliseconds.

6 Only consume data with an Exchange ID of 1002.

Consumer Command Narrative for the Second Command (line 4):







Note: The sample configuration file also shows an additional Produce and Consume command. These commands are designed to pass a time value from the DFNT to the

ACSII module and then loop back from the ASCII to the DFNT. These commands are included for testing and radio communication verification purposes only and are not necessarily required for your application.


September 6, 2007



How it's Done

1 Double-click on the icon.

2 Click the Add button. ProSoft Configuration Builder adds a default row.

3 Click the Edit button. The Edit window appears.

Define each element of the command by selecting the element, then select or enter the desired values.

4 Click OK when done.

Note : In addition to the help on the dialog, the PWP Driver Manual located on the

ProLinx Solutions CD provides descriptions of each parameter.


September 6, 2007

Page 19 of 50




This section does not contain any data for the sample application. The sample application uses UNICAST transmission and therefore there is no need to enter

IPs of other devices in this section. The ProLinx PWP Driver Manual describes this section in detail.

3.1.6 ASCII Port 0

The sample configuration file requires that this module be configured for matching serial port communication with the ASCII Communication Device.

Expand the ASCII Port 0 section.


The remaining parameters are set to ensure that the ASCII module can communicate with the PLC. Refer to the ASCII Driver Manual located on the

ProLinx solutions CD for detailed information on each of these parameters.


September 6, 2007


3.1.7 Common

Expand the Common section.




This section does not require any editing for the sample application. Refer to the

Modbus Plus Driver Manual located on the ProLinx Solutions CD for information on setting up data mapping for your application

3.2 Save and Download the Configuration File to the 6201-WA-ASCII

1

Connect your PC or LAPTOP to the DEBUG port of the 6201-WA-ASCII module. Apply power to the module if you have not already done so.

2 Choose File → Save As… and save the .PPF file to a location on your hard drive.


September 6, 2007

Page 21 of 50




3 Right-click on 6201-WA-ASCII and select Download from PC to Device.

4 Select the appropriate COM port and click the Download button.

The download is complete when the OK button becomes active. When the download is completed, click the OK button.


September 6, 2007

Configure the DFNT Module 6201-WA-ASCII ♦ ProLinx Wireless


4 Configure the DFNT Module

In This Chapter

¾ Complete the ProSoft Configuration Builder Sections............ 24

¾ Save and Download the Configuration File to the 6201-WA-DFNT

............................................................................................... 32

Based on the sample application, the remote Server is connected to a 6201-WA-

DFNT configured as a Client. The goal here is to begin to establish communications between the 6201-WA-ASCII and 6201-WA-DFNT modules.

The default configuration is designed to pass 1200 words between each module.

Each module is configured separately.

Configuration is accomplished using ProSoft Configuration Builder (PCB). The default configuration file is PROLINX WIRELESS SAMPLE.PPF.

1 Start PCB.

2

Select File → Open.

3

Navigate to the location where you copied the PROLINX WIRELESS

SAMPLE.PPF

file and select this file.

4

Expand the ASCII Serial to EtherNetIP folder.

5 Expand the 6201-WA-DFNT module selection.


September 6, 2007

Page 23 of 50



Configure the DFNT Module

4.1 Complete the ProSoft Configuration Builder Sections

4.1.1 Radio Ethernet Configuration

Double click on the selection.

Every EtherNet/IP module is set up with the defaults shown in the example. You may have to modify values such as the Radio Default Gateway, the Network

Name (SSID), and the Station Name to suit the needs of your network. The

Station Name may be modified when using more than one EtherNet/IP module.

Note: All modules must have the same Subnet Mask, Default Gateway, and Network

Name (SSID) if they are all located on the same network. Only the fourth octet in the

Radio_IP address must be different for each module. Please refer to Default Module

Configuration Assignments for a list of pre-assigned ProSoft product IP addresses.

The PWP Driver Manual located on the ProLinx Solutions CD contains a description of the remaining parameters. If you are making changes, be sure to save your changes before moving on to the next step.


September 6, 2007


Expand the Wireless Configuration section


High Speed Wireless ASCII Generic Serial Gateway and double-click on the icon.

The default Signal LED 1 through 4 parameter values are fixed and cannot be modified. If you need to change the values for the remaining parameters in this dialog box, make sure to save your changes before moving on to the next step.

As you select each parameter, the help text area in the lower right area of the dialog box displays information to help you make your selections.

Transmit Rate

This parameter defines the data rate(s) for transmission of directed messages.

Possible values are outlined in the following table.


1 Fixed 1 Mbit (1)

4

5

2

3

Fixed 2 Mbit (2)

Auto fallback high (11, 5.5, 2, 1)

Fixed medium rate (5.5)

Fixed high rate (11)


September 6, 2007

Page 25 of 50




6

7

Auto fallback standard (2, 1)

Auto fallback medium (5.5, 2, 1)


Important: For Multicast mode, use transmit rates of 1 or 2 for best results.

RTS Threshold

60 to 2347

RTS/CTS handshake threshold byte count. Less than 60 will interfere with control packets.

WEP Key Rollover

Yes or No

WEP (Wireless Encryption Protocol) is an encryption method that allows devices on a wireless network to transmit data securely.

This parameter interacts with the WATTCP file parameter "Enable Encryption" and the values for WEP Keys 1 through 4. When the WEP Key Rollover parameter is enabled, the module will randomly change the WEP key.

4.1.3 Radio SNTP Client



September 6, 2007



This section is used to synchronize the time using a centralized atomic clock.

This feature is only usable if your modules are communicating through an access point such as a RadioLinx Industrial Hotspot. The values in this window should be left with the default values. As you select each parameter, the help window on the screen displays information to help you make your selections. The PWP

Driver Manual located on the ProLinx Solutions CD describes each parameter in detail.

4.1.4 Radio PWP Exchanges


This is the area where you set up data exchange between the ASCII and the

DFNT modules. Communication is accomplished using Producer and Consumer commands. Using these commands, you specify the IP address of the receiving

(Consumer) and sending (Producer) module as well as the database locations to produce data and receive data.

In the sample application, the modules are set up to send 1200 words back and forth between the 6201-WA-ASCII and the 6201-WA-DFNT module. Each module contains a database and both modules are capable of producing or consuming data. This is accomplished using ProSoft Wireless Protocol (PWP) commands. In the sample, we are sending all 1200 words and receiving 1200 words back. We are actually sending only 50 words of data from and to the user's main and remote sites.

Two Produce commands and two Consume commands are used to make this happen. Each command sends (or receives) 600 words of data. The following example shows both produce commands from the sample application.

1 3 4 5 2 6


September 6, 2007

Page 27 of 50




1 Producer Command Narrative for the First Command (line 3):







Producer Command Narrative for the Second Command (line 4):







Note: IP Address 172.16.10.160 is the 6201-WA-ASCII module.

The Consume commands receive data coming into the module from the DFNT once configured.

1 3 4 5 2 6

Consumer Command Narrative for the First Command (line 1):


2

Consume this data only from IP Address 172.16.10.160.

3

Consume 600 words and store them beginning at DB register 0.

4

Do not use a Swap Code.

5

Consume data within 400 milliseconds.


Consumer Command Narrative for the Second Command (line 2):








September 6, 2007



Both the ASCII and the DFNT have corresponding Produce and Consume commands. The following diagram illustrates the sample application:

6201-WA-ASCII (Primary Client) PWP Exchanges

6201-WA-DFNT (Remote Client)

Note: The sample configuration file also shows an additional Produce and Consume command. These commands are designed to pass a time value from the DFNT to the

ASCII module and then loop back from the ASCII to the DFNT. These commands are included for testing and radio communication verification purposes only and are not necessarily required for your application.

This section does not contain any data for the sample application. The sample application uses UNICAST transmission and therefore there is no need to enter

IPs of other devices in this section. The ProLinx PWP Driver Manual describes this section in detail.

4.1.6 DFNT Client 0

The sample configuration file requires that the module currently being configured be configured as a Client. This is done in the DFNT Client 0 section.



September 6, 2007

Page 29 of 50





The remaining parameters are set to ensure that the DFNT module can communicate with the PLC. Refer to the DFNT Driver Manual located on the

ProLinx solutions CD for detailed information on each of these parameters.

4.1.7 DFNT Client 0 Commands SLC5002 Address Fields


Note: For command lines 1 and 2 to function properly with the ControlLogix processor, the menu item "Logic/Map PLC/SLC Messages…" in the RSLogix 5000 application, must have the "File Number" field in the "PLC 2, 3, 5/SLC Mapping" dialog box linked/associated with a user specified "Tag Name" Field Tag.


September 6, 2007



Line 1

In this command line, the DFNT continuously writes 50 words as fast as possible from the DFNT internal address 0 into the PLC slot 0, IP address 105.102.0.224.

Line 2

In this command line, the DFNT continuously reads 50 words as fast as possible from PCL slot location 0, IP address 105.102.0.224 using the function code Prot

Typed Read, and stores the data into the DFNT internal address 0.

4.1.8 CommonNet

Expand the CommonNet section.



DFNT Driver Manual located on the ProLinx Solutions CD for information on setting up data mapping for your application.


September 6, 2007

Page 31 of 50






DFNT Driver Manual located on the ProLinx Solutions CD for information on setting up data mapping for your application.

4.2 Save and Download the Configuration File to the 6201-WA-DFNT

1

Ensure that your PC or LAPTOP is still connected to the DEBUG port of the

6201-WA-DFNT module. Apply power to the module if you have not already done so.

2 Choose File → Save As… and save the .PPF file to a location on your hard drive.


September 6, 2007



3 Right-click on 6201-WA-DFCM_slc and select Download from PC to

Device .

4 Select the appropriate COM port and click the Download button.

The download is complete when the OK button becomes active. When the download is complete, click OK.


September 6, 2007

Page 33 of 50





September 6, 2007

Verify Data Exchange 6201-WA-ASCII ♦ ProLinx Wireless


Run Diagnostics Using ProSoft Configuration Builder

1 Move the connector from the Debug Port on the DFNT module and plug it into the Debug Port of the ASCII module. Ensure that power is applied to both modules.

2

Right-click on 6201-WA-ASCII and select Diagnostics.


September 6, 2007

Page 35 of 50



3 Select the appropriate Com port

Verify Data Exchange

4 Press "?" to display the Diagnostic menu.

5 Press "D" to display the Database menu.

6 Press "3" to show database registers beginning at 3000.

7 Press the "S" key to refresh the database values. The circled values in the example should change each time you press the "S" key indicating that data is being passed between modules. If these values do not change, contact

ProSoft Technical Support.

The data shown represents clock values originating from the 6201-WA-ASCII module. The values are stored in 5 registers beginning with register 3000. The clock values are being passed wirelessly to the 6201-WA-DFNT. The 6201-WA-

DFNT module is taking this data and passing it back to the 6201-WA-ASCII module and placing it into 5 registers beginning at register 3005.


September 6, 2007

Default Module Configuration Assignments 6201-WA-ASCII ♦ ProLinx Wireless


6 Default Module Configuration Assignments

In This Chapter

¾ IP

¾ WATTCP

IP Address are assigned in ranges to each of the WA modules. This information is used in the Radio Ethernet Configuration section of the configuration file. The following table shows the range assignments and the default value preconfigured in the module:

Module IP Address Range Address Set in the Module (Default)

The purpose for reserving up to 10 IP addresses per module is for addressing and establishing radio communications between modules of the same model number (for example 6201-WA-ASCII to 6201-WA-ASCII).

The following default parameters are applicable to all WA modules:

Radio_Subnet_Mask : 255.255.255.0

Radio_Default_Gateway: 172.16.10.1


September 6, 2007

Page 37 of 50



Default Module Configuration Assignments


September 6, 2007

ProSoft Technology, Inc., Support, Service & Warranty 6201-WA-ASCII ♦ ProLinx Wireless


7 ProSoft Technology, Inc., Support, Service &

Warranty

In This Chapter

¾ How to Contact Us: Sales and Support.................................. 40

¾ Return Material Authorization (RMA) Policies and Conditions41

¾ Procedures for Return of Units Under Warranty..................... 41

¾ Procedures for Return of Units Out of Warranty..................... 42

¾ LIMITED

Be sure and read the full Warranty that can be found on our web site at www.prosoft-technology.com

for details and other terms and conditions. The content in this summary is subject to change without notice. The content is current at date of publication.

ProSoft Technology, Inc. strives to provide meaningful support to its customers.

Should any questions or problems arise, please feel free to contact us at:

Internet

Web Site: http://www.prosoft-technology.com/support

E-mail address: [email protected]

Those of us at ProSoft Technology, Inc. want to provide the best and quickest support possible, so before calling please have the following information available. You may wish to fax this information to us prior to calling.

1 Product Version Number

2 System architecture

3 Network details

In the case of hardware, we will also need the following information:

1 Module configuration and contents of file

2 Module Operation

3 Configuration/Debug status information

4 LED patterns

5 Information about the processor and user data files as viewed through the development software and LED patterns on the processor

6 Details about the networked devices interfaced, if any

For technical support calls within the United States, an after-hours answering system allows pager access to one of our qualified technical and/or application support engineers at any time to answer your questions.


September 6, 2007

Page 39 of 50

6201-WA-ASCII ♦ ProLinx Wireless ProSoft Technology, Inc., Support, Service & Warranty


7.1 How to Contact Us: Sales and Support

All ProSoft Technology Products are backed with full technical support. Contact our worldwide Technical Support team and Customer Service representatives directly by phone or email:

USA / Latin America (excluding Brasil) (Office in California)

+1(661) 716-5100

+1(661) 716-5101 (Fax)

1675 Chester Avenue, 4th Floor

Bakersfield, California 93301

U.S.A.

+1.661.716.5100, [email protected]

Languages spoken include: English, Spanish

Asia Pacific (office in Malaysia)

+603.7724.2080

+603.7724.2090 (Fax)

C210, Damansara Intan,

1 Jalan SS20/27, 47400 Petaling Jaya

Selangor, Malaysia

+603.7724.2080, [email protected]

Languages spoken include: Chinese, Japanese, English

China Pacific (office in China)

+86.21.64518356 x 8011

+86.21.64756957 (Fax)

4/F, No. 16 Hongcao Road

Shanghai, China 200233

China

+86.21.64518356 x 8011, [email protected]

Languages spoken include: Chinese, English

Europe / Middle East / Africa (office in Toulouse, France)

+33 (0) 5.34.36.87.20

+33 (0) 5.61.78.40.52 (Fax)

Zone d'activité de Font Grasse

17, rue des Briquetiers

F-31700 Blagnac

France

+33 (0) 5.34.36.87.20. support. [email protected]

Languages spoken include: French, English

Brasil (office in Sao Paulo)

+55-11-5084-5178

+55-11-5083-3776 (Fax)

Rua Vergueiro, 2949 - sala 182 - Edifício Vergueiro Work Center

Vila Mariana - São Paulo

Cep: 04101-300 – Brasil

+55-11-5084-5178, [email protected]

Languages spoken include: Portuguese, English


September 6, 2007



7.2 Return Material Authorization (RMA) Policies and Conditions

The following RMA Policies and Conditions apply to any returned product. These

RMA Policies are subject to change by ProSoft without notice. For warranty information, see Section C below entitled "Limited Warranty". In the event of any inconsistency between the RMA Policies and the Warranty, the Warranty shall govern.

7.2.1 All Product Returns

1 In order to return a Product for repair, exchange or otherwise, the Customer must obtain a Returned Material Authorization (RMA) number from ProSoft and comply with ProSoft shipping instructions.

2 In the event that the Customer experiences a problem with the Product for any reason, Customer should contact ProSoft Technical Support at one of the telephone numbers listed above in Section A. A Technical Support Engineer will request several tests in an attempt to isolate the problem. If after these tests are completed, the Product is found to be the source of the problem,

ProSoft will issue an RMA.

3 All returned Products must be shipped freight prepaid, in the original shipping container or equivalent, to the location specified by ProSoft, and be accompanied by proof of purchase. The RMA number is to be prominently marked on the outside of the shipping box. Customer agrees to insure the

Product or assume the risk of loss or damage in transit. Products shipped to

ProSoft without an RMA number will be returned to the Customer, freight collect. Contact ProSoft Technical Support for further information.

4 Out of warranty returns are not allowed on RadioLinx accessories such as antennas, cables, and brackets.

The following policy applies for Non-Warranty Credit Returns:

A

B

10% Restocking Fee if Factory Seal is not broken

20% Restocking Fee if Factory Seal is broken

ProSoft retains the right, in its absolute and sole discretion, to reject any nonwarranty returns for credit if the return is not requested within three (3) months after shipment of the Product to Customer, if the Customer fails to comply with

ProSoft's shipping instructions, or if the Customer fails to return the Product to

ProSoft within six (6) months after Product was originally shipped.

7.3 Procedures for Return of Units Under Warranty

1 A Technical Support Engineer must pre-approve all product returns.

2 Module is repaired or replaced after a Return Material Authorization Number is entered and a replacement order is generated.

3 Credit for the warranted item is issued within 10 business days after receipt of product and evaluation of the defect has been performed by ProSoft. The credit will only be issued provided the product is returned with a valid Return

Material Authorization Number and in accordance with ProSoft's shipping instructions.


September 6, 2007

Page 41 of 50


High Speed Wireless ASCII Generic Serial Gateway a) If no defect is found, a credit is issued. b) If a defect is found and is determined to be customer generated or if the defect is otherwise not covered by ProSoft's Warranty, or if the module is not repairable, a credit is not issued and payment of the replacement module is due.

7.4 Procedures for Return of Units Out of Warranty

1 Customer sends unit in for evaluation.

2 If no defect is found, Customer will be charged the equivalent of US $100 plus shipping, duties and taxes that may apply. A new Purchase Order will be required for this evaluation fee.

If the unit is repaired the charge to the Customer will be 30%* of the list price plus any shipping, duties and taxes that may apply. A new Purchase Order will be required for a product repair.

3 For an immediate exchange, a new module may be purchased and sent to

Customer while repair work is being performed. Credit for purchase of the new module will be issued when the new module is returned in accordance with ProSoft's shipping instructions and subject to ProSoft's policy on nonwarranty returns. This is in addition to charges for repair of the old module and any associated charges to Customer.

4 If, upon contacting ProSoft Customer Service, the Customer is informed that unit is believed to be unrepairable, the Customer may choose to send unit in for evaluation to determine if the repair can be made. Customer will pay shipping, duties and taxes that may apply. If unit cannot be repaired, the

Customer may purchase a new unit.

3150-All

3750

3600-All

3700

3170-All

3250

1560 can be repaired, if defect is the power supply

1550 can be repaired, if defect is the power supply

3350

3300

1500-All

* 30% of list price is an estimated repair cost only. The actual cost of repairs will be determined when the module is received by ProSoft and evaluated for needed repairs.


September 6, 2007



Purchasing Warranty Extension

As detailed below in ProSoft's Warranty, the standard Warranty Period is one year (or in the case of RadioLinx modules, three years) from the date of delivery.

The Warranty Period may be extended for an additional charge, as follows:

Additional 1 year = 10% of list price

Additional 2 years = 20% of list price

Additional 3 years = 30% of list price

This Limited Warranty ("Warranty") governs all sales of hardware, software and other products (collectively, "Product") manufactured and/or offered for sale by

ProSoft, and all related services provided by ProSoft, including maintenance, repair, warranty exchange, and service programs (collectively, "Services"). By purchasing or using the Product or Services, the individual or entity purchasing or using the Product or Services ("Customer") agrees to all of the terms and provisions (collectively, the "Terms") of this Limited Warranty. All sales of software or other intellectual property are, in addition, subject to any license agreement accompanying such software or other intellectual property.

7.5.1 What Is Covered By This Warranty

A

B

Warranty On New Products : ProSoft warrants, to the original purchaser only, that the Product that is the subject of the sale will (1) conform to and perform in accordance with published specifications prepared, approved, and issued by ProSoft, and (2) will be free from defects in material or workmanship; provided these warranties only cover Product that is sold as new. This Warranty expires one year (or in the case of RadioLinx modules, three years) from the date of shipment (the "Warranty Period").

If the Customer discovers within the Warranty Period a failure of the

Product to conform to specifications, or a defect in material or workmanship of the Product, the Customer must promptly notify ProSoft by fax, email or telephone. In no event may that notification be received by

ProSoft later than 15 months (or in the case of RadioLinx modules, 39 months) from the date of delivery. Within a reasonable time after notification, ProSoft will correct any failure of the Product to conform to specifications or any defect in material or workmanship of the Product, with either new or used replacement parts. Such repair, including both parts and labor, will be performed at ProSoft's expense. All warranty service will be performed at service centers designated by ProSoft. If

ProSoft is unable to repair the Product to conform to this Warranty after a reasonable number of attempts, ProSoft will provide, at its option, one of the following: a replacement product, a full refund of the purchase price or a credit in the amount of the purchase price. All replaced product and parts become the property of ProSoft. These remedies are the Customer's only remedies for breach of warranty.

Warranty On Services : Material and labor used by ProSoft to repair a verified malfunction or defect are warranted on the terms specified above


September 6, 2007

Page 43 of 50



C for new Product, provided said warranty will be for the period remaining on the original new equipment warranty or, if the original warranty is no longer in effect, for a period of 90 days from the date of repair.

The Warranty Period for RadioLinx accessories (such as antennas, cables, brackets, etc.) are the same as for RadioLinx modules, that is, three years from the date of shipment.

7.5.2 What Is Not Covered By This Warranty

A

B

C

D

ProSoft makes no representation or warranty, expressed or implied, that the operation of software purchased from ProSoft will be uninterrupted or error free or that the functions contained in the software will meet or satisfy the purchaser's intended use or requirements; the Customer assumes complete responsibility for decisions made or actions taken based on information obtained using ProSoft software.

With the exception of RadioLinx accessories referenced in paragraph 1(c) this Warranty does not cover any product, components, or parts not manufactured by ProSoft.

This Warranty also does not cover the failure of the Product to perform specified functions, or any other non-conformance, defects, losses or damages caused by or attributable to any of the following: (i) shipping; (ii) improper installation or other failure of Customer to adhere to ProSoft's specifications or instructions; (iii) unauthorized repair or maintenance; (iv) attachments, equipment, options, parts, software, or user-created programming (including, but not limited to, programs developed with any

IEC 61131-3 programming languages, or "C") not furnished by ProSoft; (v) use of the Product for purposes other than those for which it was designed; (vi) any other abuse, misapplication, neglect or misuse by the

Customer; (vii) accident, improper testing or causes external to the

Product such as, but not limited to, exposure to extremes of temperature or humidity, power failure or power surges outside of the limits indicated on the product specifications; or (viii) disasters such as fire, flood, earthquake, wind or lightning.

The information in this Agreement is subject to change without notice.

ProSoft shall not be liable for technical or editorial errors or omissions made herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of this material. The user guides included with your original product purchased by you from ProSoft, contains information protected by copyright. No part of the guide may be duplicated or reproduced in any form without prior written consent from

ProSoft.


September 6, 2007



7.5.3 DISCLAIMER REGARDING HIGH RISK ACTIVITIES

PRODUCT MANUFACTURED OR SUPPLIED BY PROSOFT IS NOT FAULT

TOLERANT AND IS NOT DESIGNED, MANUFACTURED OR INTENDED FOR

USE IN HAZARDOUS ENVIRONMENTS REQUIRING FAIL-SAFE

PERFORMANCE (INCLUDING, WITHOUT LIMITATION, THE OPERATION OF

NUCLEAR FACILITIES, AIRCRAFT NAVIGATION OF COMMUNICATION

SYSTEMS, AIR TRAFFIC CONTROL, DIRECT LIFE SUPPORT MACHINES

OR WEAPONS SYSTEMS), IN WHICH THE FAILURE OF THE PRODUCT

COULD LEAD DIRECTLY OR INDIRECTLY TO DEATH, PERSONAL INJURY,

OR SEVERE PHYSICAL OR ENVIRONMENTAL DAMAGE (COLLECTIVELY,

"HIGH RISK ACTIVITIES"). PROSOFT SPECIFICALLY DISCLAIMS ANY

EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR HIGH RISK

ACTIVITIES.

7.5.4 DISCLAIMER OF ALL OTHER WARRANTIES

THE WARRANTIES SET FORTH IN PARAGRAPH 1 ABOVE ARE IN LIEU OF

ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT

LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE.

7.5.5 LIMITATION OF REMEDIES**

IN NO EVENT WILL PROSOFT (OR ITS DEALER) BE LIABLE FOR ANY

SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES BASED ON

BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT

TORT, OR ANY OTHER LEGAL THEORY. DAMAGES THAT PROSOFT AND

ITS DEALER WILL NOT BE RESPONSIBLE FOR INCLUDE, BUT ARE NOT

LIMITED TO: LOSS OF PROFITS; LOSS OF SAVINGS OR REVENUE; LOSS

OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT; LOSS OF

DATA; COST OF CAPITAL; COST OF ANY SUBSTITUTE EQUIPMENT,

FACILITIES, OR SERVICES; DOWNTIME; THE CLAIMS OF THIRD PARTIES,

INCLUDING CUSTOMERS OF THE PURCHASER; AND INJURY TO

PROPERTY.

** Some areas do not allow time limitations on an implied warranty, or allow the exclusion or limitation of incidental or consequential damages. In such areas the above limitations may not apply. This Warranty gives you specific legal rights, and you may also have other rights which vary from place to place.

7.5.6 Time Limit for Bringing Suit

Any action for breach of warranty must be commenced within 15 months (or in the case of RadioLinx modules, 39 months) following shipment of the Product.


September 6, 2007

Page 45 of 50



Unless modified in writing and signed by both parties, this Warranty is understood to be the complete and exclusive agreement between the parties, suspending all oral or written prior agreements and all other communications between the parties relating to the subject matter of this Warranty, including statements made by salesperson. No employee of ProSoft or any other party is authorized to make any warranty in addition to those made in this Warranty. The

Customer is warned, therefore, to check this Warranty carefully to see that it correctly reflects those terms that are important to the Customer.

B

C

D

A

E

Any documentation included with Product purchased from ProSoft is protected by copyright and may not be photocopied or reproduced in any form without prior written consent from ProSoft.

ProSoft's technical specifications and documentation that are included with the Product are subject to editing and modification without notice.

Transfer of title shall not operate to convey to Customer any right to make, or have made, any Product supplied by ProSoft.

Customer is granted no right or license to use any software or other intellectual property in any manner or for any purpose not expressly permitted by any license agreement accompanying such software or other intellectual property.

Customer agrees that it shall not, and shall not authorize others to, copy software provided by ProSoft (except as expressly permitted in any license agreement accompanying such software); transfer software to a third party separately from the Product; modify, alter, translate, decode, decompile, disassemble, reverse-engineer or otherwise attempt to derive the source code of the software or create derivative works based on the software; export the software or underlying technology in contravention of applicable US and international export laws and regulations; or use the software other than as authorized in connection with use of Product.

Intellectual Property

In addition to complying with the Terms of this Warranty, Customers purchasing software or other intellectual property shall comply with any license agreement accompanying such software or other intellectual property. Failure to do so may void this Warranty with respect to such software and/or other intellectual property.


September 6, 2007



7.5.10 Allocation of risks

This Warranty allocates the risk of product failure between ProSoft and the

Customer. This allocation is recognized by both parties and is reflected in the price of the goods. The Customer acknowledges that it has read this Warranty, understands it, and is bound by its Terms.

7.5.11 Controlling Law and Severability

This Warranty shall be governed by and construed in accordance with the laws of the United States and the domestic laws of the State of California, without reference to its conflicts of law provisions. If for any reason a court of competent jurisdiction finds any provisions of this Warranty, or a portion thereof, to be unenforceable, that provision shall be enforced to the maximum extent permissible and the remainder of this Warranty shall remain in full force and effect. Any cause of action with respect to the Product or Services must be instituted in a court of competent jurisdiction in the State of California.


September 6, 2007

Page 47 of 50




September 6, 2007

Index

A

About Transmission Casts • 10

Additional Restrictions Relating To Software

And Other Intellectual Property • 46

All Product Returns • 41

Allocation of risks • 47

ASCII Port 0 • 20

Before You Begin • 7

B

C

Common • 21

CommonNet • 31

Complete the ProSoft Configuration Builder

Sections • 14, 24

Configure the ASCII Module • 13

Configure the DFNT Module • 23

Controlling Law and Severability • 47

Copy the Sample Application File • 12

D

Default Module Configuration Assignments •

37

DFNT Client 0 • 29

DFNT Client 0 Commands SLC5002

Address Fields • 30

DISCLAIMER OF ALL OTHER

WARRANTIES • 45

DISCLAIMER REGARDING HIGH RISK

ACTIVITIES • 45

H

How it's Done • 19

How to Contact Us

Sales and Support • 40

I

Important Installation Instructions • 2

Install ProSoft Configuration Builder (PCB) •

11

Intellectual Property • 46

Introduction • 7

IP Addresses • 37


September 6, 2007


L

LIMITATION OF REMEDIES** • 45

LIMITED WARRANTY • 43

Line 1 • 31

Line 2 • 31

Load the Required Software • 11

N

No Other Warranties • 46

P

Please Read This Notice • 2

Procedures for Return of Units Out of

Warranty • 42

Procedures for Return of Units Under

Warranty • 41

ProSoft Technology, Inc., Support, Service &

Warranty • 39

Purchasing Warranty Extension • 43

R

Radio Configuration • 15, 25

Radio Ethernet Configuration • 14, 24

Radio PWP Exchanges • 17, 27

Radio PWP Multicast Group List • 20, 29

Radio SNTP Client • 16, 26

Return Material Authorization (RMA) Policies and Conditions • 41

RTS Threshold • 15, 26

S

Save and Download the Configuration File to the 6201-WA-ASCII • 21

Save and Download the Configuration File to the 6201-WA-DFNT • 32

T

Time Limit for Bringing Suit • 45

Transmit Rate • 16, 25

U

Un-repairable Units • 42

Using the Sample ProSoft Configuration

Builder Files • 8

V

Verify Data Exchange • 35

Page 49 of 50



W

WATTCP Parameters • 37

WEP Key Rollover • 16, 26

What Is Covered By This Warranty • 43

What Is Not Covered By This Warranty • 44

Y

Your Feedback Please • 3

Index


September 6, 2007

ProLinx 6201-WA-DFNT to DFNT Setup guide

6201-WA-ASCII to 6201-WA-DFNT

Please Read This Notice

Important Installation Instructions

Your Feedback Please

Contents

1 Introduction

1.1 Before You Begin

1.2 Using the Sample ProSoft Configuration Builder Files

1.3 About Transmission Casts

2 Load the Required Software

2.1 Install ProSoft Configuration Builder (PCB)

2.2 Copy the Sample Application File

3.1 Complete the ProSoft Configuration Builder Sections

3.1.1 Radio Ethernet Configuration

3.1.3 Radio SNTP Client

3.1.4 Radio PWP Exchanges

3.1.6 ASCII Port 0

3.1.7 Common

3.2 Save and Download the Configuration File to the 6201-WA-ASCII

4 Configure the DFNT Module

4.1 Complete the ProSoft Configuration Builder Sections

4.1.1 Radio Ethernet Configuration

4.1.3 Radio SNTP Client

4.1.4 Radio PWP Exchanges

4.1.6 DFNT Client 0

4.1.7 DFNT Client 0 Commands SLC5002 Address Fields

4.1.8 CommonNet

4.2 Save and Download the Configuration File to the 6201-WA-DFNT

6 Default Module Configuration Assignments

7 ProSoft Technology, Inc., Support, Service &

Warranty

7.1 How to Contact Us: Sales and Support

7.2 Return Material Authorization (RMA) Policies and Conditions

7.2.1 All Product Returns

7.3 Procedures for Return of Units Under Warranty

7.4 Procedures for Return of Units Out of Warranty

7.5.1 What Is Covered By This Warranty

7.5.2 What Is Not Covered By This Warranty

7.5.3 DISCLAIMER REGARDING HIGH RISK ACTIVITIES

7.5.4 DISCLAIMER OF ALL OTHER WARRANTIES

7.5.5 LIMITATION OF REMEDIES**

7.5.6 Time Limit for Bringing Suit

Intellectual Property

7.5.10 Allocation of risks

7.5.11 Controlling Law and Severability

Index

Related manuals

ProLinx

6201-WA-DFNT to DFNT

ProSoft Technology

5202-MNET-ASCII4

ProSoft Technology

5201-DFNT-DNPSNET

ProSoft Technology

5209-DFNT-CCLINK

Table of contents