Blaupunkt | 23/194J-GB-4B-HCU | User guide | Blaupunkt 23/194J-GB-4B-HCU User guide

Blaupunkt 23/194J-GB-4B-HCU User guide
HD Ready LED TV with Freeview & USB Media Player
User Guide
Model No
23/194J-GB-4B-HCU
23/194J-GB-4B-HCDU
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd 1
12/4/2013 11:30:34 AM
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions. All the safety and operating instructions should be read before the
appliance is operated.
Warnings
Maintenance
• To reduce the risk of fire, electric shock or
damage to the television, do not expose it to
dust, rain or moisture, or place any objects filled
with liquids on or near the television.
• Do not place the television in a confined space,
ensure that nothing can obstruct the ventilation
openings at the rear of the television.
• To clean this unit, wipe with a soft, dry cloth. If
the surfaces are extremely dirty, use a soft cloth
dipped in a soap and water solution or a weak
detergent solution.
• Never use alcohol, paint thinner or benzene to
clean this unit.
• Before using a chemically treated cloth, read the
instructions that came with the cloth carefully.
To prevent spread of fire,
keep candles or other open
flames away from this
product at all times
CAUTION: If water or other liquid enters the
television through the display panel surface, a
malfunction may occur.
• Dispose of this television and any components
including batteries in an environmentally friendly
manner. If in doubt, please contact your local
authority for details of recycling.
Safety
• For your safety, this appliance is fitted with a
fused moulded 3 pin mains plug. Should the
fuse need to be replaced, ensure that any
replacement is of the same amperage and
approved with the BSI mark.
• Never try and replace the mains plug unless
you have adequate qualifications and are
legally authorised to do so. In the event that a
replacement Mains cable is required, contact the
manufacturer for a suitable replacement.
• Never use the television if it is damaged in
any way.
• Always place the television on a flat level surface
avoiding anywhere which may be subject to
strong vibration.
• Ensure the television is not placed on top of the
power cable as the weight of the television may
damage the cable and cause a safety hazard.
• Never place mobile phones, speakers or any
other device which may cause magnetic or radio
interference with the television. If interference
is apparent, move the device causing the
interference away from the television.
• To disconnect the apparatus from the mains,
please use the switch located on the underside/
rear of the TV. The switch shall remain readily
operable.
• When installing on a wall, ensure the TV is at
least 5cm from the wall for ventilation
Packaging
• The safest way to transport your item is in
the original box/packaging - please save your
packaging for this.
• You will need original box/packaging in the
event of warranty/service repair or support. We
are unable to carry out warranty/service if you
are unable to package it correctly.
4
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:4
12/4/2013 11:30:36 AM
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions. All the safety and operating instructions should be read before the
appliance is operated.
Important Information Regarding Use of
Video Games, Computers, Captions or Other
Fixed Image Displays
The extended use of fixed image program material
can cause a permanent “shadow image” on the
LCD/LED panel.
This background image is viewable on normal
programs in the form of a stationary fixed
image. This type of irreversible LCD/LED panel
deterioration can be limited by observing the
following steps:
1. Reduce the brightness/contrast setting to a
minimum viewing level.
2. Do not display the fixed image for extended
periods of time.
3. Turn the power off when not in actual use.
•
•
•
•
•
Examples of images that you need to watch out
for are as follows (this is not an exhaustive list):
TV Channel Logos: e.g. Shopping channel logos
and pricing displays-especially if they are
bright and stationary. Moving or low-contrast
graphics are less likely to cause ageing of the
screen.
Time Displays
Teletext: Do not view a stationary page for a
long period of time
TV/DVD Menus: e.g. Listings of DVD disc content
Pause Mode: Do not leave the TV in pause mode
for long periods of time, e.g. When watching
DVDs or videos.
How do I dispose of this product?
UK: Waste electrical products should not be
disposed of with household waste. Separate
disposal facilities exist. For your nearest facilities,
please see www.recycle-more.co.uk or in store for
details.
ROI: Waste electrical products should not be
disposed of with household waste. Separate
disposal facilities exist. Check with your Local
Authority or retailer for recycling advice.
Batteries
• Do not expose batteries to high
temperatures, excessive heat,
prolonged sunshine or fire
as this may cause leakage,
explosion or ignition.
• Observe the correct polarity when
inserting batteries.
• Do not use different types of
batteries together or mix old and
new batteries.
• Dispose of batteries in an
environmentally friendly way.
• Certain regions may regulate the
disposal of batteries.
Please consult your local authority.
Cd
Important - Once ‘shadow image/screen burn’
occurs, it will never disappear and is not repairable
under warranty.
5
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:5
12/4/2013 11:30:36 AM
CONTENTS
Manufacturers Guarantee Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
What is included in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Attaching/Detaching the stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Wall mounting/Securing the TV to a wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
TV Buttons and Input Source Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
TV Menu Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-22
Channel Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Picture Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18
Sound Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Time Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Option Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Lock Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
PC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7 Day TV Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DVD Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
USB Mode / Media Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-29
Using your TV with a Sky digital set top box . . . . . . . . . . . . . . . . . . . . . . . . 27
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:7
12/4/2013 11:30:37 AM
What is included in the box
WHAT IS INCLUDED IN THE BOX
Accessories
Included with this TV are the following accessories
1 x User Guide
1 x Remote Control
User Guide
2 x AAA Batteries
1 x Quick Start Guide
Quick Start
Guide
1 x Mini Component / YPbPr
1 x TV
1 x Mini Composite / Video
1 x RF Cable
1 x Stand Installation Pack
(Includes stand base, stand neck & screws)
Please save your packaging as you will need this in the event of warranty/service repair or support. We
are unable to carry out warranty/service if you are unable to package it correctly. The safest way to
package your item in the event of warranty/service repair is in it’s original box/packaging.
8
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:8
12/4/2013 11:30:37 AM
Attaching / Detaching the stand
ATTACHING/DETACHING THE STAND
Attaching the Stand
To complete stand installation you will need a Philips screwdriver.
(fig.1)
(fig.1) Attach the stand neck (b) to the body
of TV (a).
(fig.2)
(fig.2) Secure the stand neck to the TV with
the (c) 4 x M4x10 (M4x8) screws supplied.
(fig.3)
(fig.3) Insert the TV into the stand (d) at 45 degrees then gently twist the TV into the CLOSE position until
it clicks into place (e)
Detaching the Stand
Remove the screws highlighted then remove the stand base and neck from the rear of the TV set.
9
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:9
12/4/2013 11:30:43 AM
Wall mounting / Securing the TV to a Wall
WALL MOUNTING
Wall mounting the TV
IMPORTANT - Before drilling any holes in the wall ensure you are not drilling
where there could be any electric wires, water or gas pipes.
1) Remove the four screws highlighted that are supplied in the wall
mounting holes.
2) The wall mount can now be easily attached to the mounting holes on the
rear of the TV.
fig 1
INCORRECT
Important – If wall mounting this TV, only
use the screws already provided in the wall
mounting holes. Using other screws which
are longer could cause irreparable damage to
internal parts.
Viewing angle
TV
For optimum viewing, if wall mounting the TV
higher than eye level, the TV should be tilted
downwards so that the TV’s screen is ‘face on’.
See fig 1 and 2
fig 2
CORRECT
Viewing angle
Securing the TV to a Wall
For your safety you can secure the TV to a wall using a fastening chord. With this method you can prevent
the TV from falling forward which could cause injury and/or damage to the TV.
A) Using one or both of the top wall-mounting
holes and screws (the screws are already supplied
in the wall mounting holes) fasten one end of the
fastening chord/s to the TV.
B) Secure the other end of the fastening chord/s to
your wall. (you will need screws/fixings suitable for
your wall type - available separately from most
DIY stores)
Note - Please ensure that children do not climb on the TV set.
11
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:11
12/4/2013 11:30:43 AM
TV Buttons and Source Menu
TV BUTTONS & SOURCE MENU
This information is for models
This information is for models
without built in DVD players
1
1
with built in DVD players
2
2
3
4
3
4
5
5
6
6
7
7
8
9
1 Volume up and menu right
1 Stop/Eject Disc
2 Volume down and menu left
2 Play/Pause Disc
3 Programme/Channel up and menu up
3 Volume up and menu right
4 Programme/Channel down and menu down
4 Volume down and menu left
5 Displays Menu/OSD
5 Programme/Channel up and menu up
6 Displays the input source menu
6 Programme/Channel down and menu down
7 Standby Power On/Off
7 Displays Menu/OSD
8 Displays the input source menu
9 Standby Power On/Off
Choosing Mode Input/Source
To switch between the different input/
connections.
A) Using the buttons on the remote control:
1) Press [SOURCE] - The source menu will
appear
2) Press [\/] or [/\] to select the input you
require.
3) Press [OK]
B) Using the buttons on the Television:
1) Press [SOURCE]
2) Scroll up / down using CH+/ CH- buttons to
the input/source you require
3) Press Vol+ to change input/source to the
one selected.
Example of Source menu
depending on the TV model
12
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:12
12/4/2013 11:30:43 AM
Remote Control
REMOTE CONTROL
1
STANDBY - Switch on TV when in standby or vice versa
MUTE - Mute the sound or vice versa
DTV - Switch to Freeview source
RADIO - Switch to radio whilst in Freeview source
USB - Switch to USB source
DVD - Switch to DVD source
2
NUMBER BUTTONS - 0 – 9 to select a TV channel directly.
TV GUIDE - Opens the 7 Day TV Guide (Freeview mode)
- To return to the previous channel viewed
3
4
VOL (+/-) - To increase / decrease the sound level
P.MODE - Scrolls through picture mode options
S.MODE - Scrolls through sound mode options
FAV - To display favourites menu
CH (+/-) - To increase or decrease the channel being watched
MENU - To display OSD menu
EXIT - To exit all menus
- Allows you to navigate the on-screen menus
and adjust the system settings to your preference
SOURCE - To display the input/source menu
INFO - Press once for now/next channel information
Press twice for programme information about current
programme
ASPECT - To switch the screen between the different picture
formats
SLEEP - Press repeatedly to cycle through the sleep options
AUDIO - To change the audio language (if available)
SUBTITLE - To switch the dialogue at the bottom of the screen
(on/off)
TEXT - To enter/exit Teletext (Analogue TV)
TEXT HOLD - Teletext mode - Hold current page which is
displayed (Analogue TV)
DISPLAY - To switch off the screen when listening to radio
TEXT/DVD ZOOM - Zoom function for Teletext and DVD
DVD MENU/RECORD - Access the DVD root menu and USB
record function
- To restart the current chapter
- To advance forward to the next chapter
- To stop the playback/Eject Disc
(To EJECT the disc press/hold the
button for 4 seconds)
1
2
3
4
- To play in fast rewind mode
- To play in fast forward mode
- To play/pause
DVD SETUP/REC LIST - Opens up DVD Menu or Opens the list
of what has been previously recorded
GOTO - To go to a specific chapter
A-B - Press once to set point, press a second time to return
to point
ANGLE - Select different angle of DVD
3D - Change to 3D mode
REPEAT - To repeat playback
For Models with Integrated DVD players
For Models with PVR Function
For Models with USB Playback
For Models with 3D Feature
13
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:13
12/4/2013 11:30:48 AM
Connections
CONNECTIONS
C
B
A
V G A /P C (A udio in)
HDMI 1
F
G
H
I
J
C OAX
AV IN
Y P bP r
HDMI 2
US B
D
E
V G A /P C IN
K
L
C I C A R D IN
E A R P HO NE
A
HDMI 1
HDMI input
G
AV in
Audio / Video Input
B
SCART
SCART Input
H
YPbPr
Component HD Input
C
VGA(PC) Audio In
3.5mm PC audio input
I
HDMI 2
HDMI input
D
VGA(PC)
VGA-PC input
J
USB
USB input
E
RF IN
RF / TV Aerial Input
K
CI CARD IN
Common Interface Card Input
F
COAX Audio Out
Digital Coax output
L
EARPHONE
3.5mm Earphone output
Connecting to a Camcorder, Camera or Games Console
TV Source should be set to Video
Audio
R/L
Video
14
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:14
12/4/2013 11:30:49 AM
Connections
CONNECTIONS
Connecting to a device with SCART output
TV Source should be set to SCART
SCART
OUT
SCART
IN
RF OUT
RF IN
RF IN
Connecting to a device with HDMI output
A HDMI cable can output both video and audio and enables you to enjoy digital-quality video and audio
with minimal loss of quality.
TV Source should be set to the corresponding HDMI port (HDMI 1, HDMI 2 etc)
Note: To use this model TV as a PC/laptop monitor it will need to be connected via the VGA input, it
can not be used as a PC/laptop monitor via the HDMI input. The HDMI Input is provided to view digital
content with compatible external devices
Connecting to a device with Component/YPbPr output
If you are supplied with a cable from the device which has RED, GREEN, BLUE, RED & WHITE connectors
you must connect via Component (for picture) and by phono cable (for sound).
TV Source should be set to Component.
Y
PB
Mini
YPbPr
PR
L
L
R
R
Connecting to a device with VGA/PC output (Laptop or Desktop Computer)
TV Source should be set to VGA/PC
VGA/PC
IN
VGA/PC
OUT
VGA/PC
(AUDIO
IN)
AUDIO
OUT
15
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:15
12/4/2013 11:30:49 AM
TV Menu Operation
CHANNEL MENU
To access this menu, press [MENU] button on the remote control.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Auto Scan - Allows you to retune the television for all digital channels, digital radio stations and analogue
channels.
DTV Manual Tuning- Allows you to manually tune your digital signal
Programme Edit - Allows you to delete, skip and add favourite channels
Signal Information - Displays signal strength information.
CI Information - Pay per view services require a “smartcard” to be inserted into the TV.
If you subscribe to a pay per view service the provider will issue you with a ‘CAM’ and a “smartcard”. The
CAM can then be inserted into the COMMON INTERFACE PORT (CI Card In).
Tip: If you do not press any buttons for 30 seconds, the menu will automatically exit. You can change
the length of time before the menu exits automatically - see ‘OSD Duration’ in the Option Menu
16
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:16
12/4/2013 11:30:51 AM
TV Menu Operation
PICTURE MENU
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Picture Mode - Choose from the following presets:
Home Mode
Power saving mode which reduces the energy used by up to
25% (by reducing the power to the LED/LCD panel).
In Home Mode, the TV will switch itself to Standby mode
after 3-5 hours in the event that the TV buttons or remote
control buttons are not pressed (change the picture mode to
another setting to de-activate this function)
Standard
Standard settings
Dynamic
Recommended settings for fast moving pictures
Mild
Set to be lighter in colour and less bright
Personal
Lets you manually alter all the settings
You can make the following adjustments in Personal mode:
Contrast - Switch the balance between black and white.
Brightness - Increase or decrease the brightness of the picture.
Colour - Increases the colour from black and white.
Sharpness - Increase or decrease the sharpness of the picture.
Tint - Lets you increase or decrease the level of tint within the picture
(only available in VGA/PC source mode).
Colour Temperature Choose from the following presets:
Normal
Default settings
Warm
Increases red within the picture
Cold
Increases blue within the picture
17
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:17
12/4/2013 11:30:52 AM
TV Menu Operation
PICTURE MENU
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Aspect Ratio - Within the UK the picture format varies depending on the channel/broadcast. There are a
number of different options to best meet your needs.
Zoom
16:9
The picture
is the correct
proportion but
zoomed in to
fill the screen
Fills the screen
with a regular
16:9 signal and
4:3 will stretch
to fill the screen
Original
4:3
14:9
Will display the picture from the
broadcaster without any change
Displays the 4:3
picture in its
original size.
Side bars are
shown to fill
the 16:9 screen
Displays the
14:9 picture
in the correct
proportion. As
a result side
bars are shown
on the screen
Auto
Automatically displays the best
picture format. So the picture is in
the correct position. May have black
lines at the top/bottom
and/or sides.
Noise Reduction - Choose from the following presets
Off
Turns noise reduction off
Low
Minor system adjustment
Middle
Medium system adjustments
High
Maximum system adjustments
Default
Default settings
PC Setup - Please refer to PC settings page.
18
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:18
12/4/2013 11:30:53 AM
TV Menu Operation
SOUND MENU
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Sound Mode - Choose from the following presets
Standard
Default settings
Music
Emphasises music over voices
Movie
Provides live and full sound for movies
Personal
Selects your personal sound settings
Sports
Emphasises sound for sports
Tip: Treble and bass levels can only be adjusted when the sound mode ‘Personal’ is selected.
Treble - To adjust the amount of high frequency within the sound.
Bass - To adjust the amount of low frequency within the sound.
Balance - To switch the sound between the left and right speakers.
Auto Volume Level (AVL) - When ‘on’ is selected, the volume will stay at a constant level regardless of
input/source
Surround Sound - Allows user to switch surround sound on or off.
AD Switch- This allows the user to turn AD (Audio Description) on or off
AD Volume- This allows the user to adjust the volume of the AD (Audio Description)
(Audio Description is a service available on certain programmes. It provides a description of what is
happening during the selected programme for a person who is visually impaired)
SPDIF Mode - This is the digital COAX Audio output. Choose from the following options:
Off
Off
Auto
Selects the best settings automatically
PCM
Select this option if you are connecting to a Stereo Hi-fi via coax cable (Pulse-code
modulation (PCM) is a digital representation of an analogue signal)
19
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:19
12/4/2013 11:30:54 AM
TV Menu Operation
TIME MENU
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Clock - Shows the date and time
Off Time - Allows you to set a specific time for your TV to turn off
On Time - Allows you to set a specific time for your TV to turn on, the channel it will then display, the
source it will be on and also the volume. This function can then be toggled to repeat every day or a
certain day (the TV must be in standby mode for this to be effective)
Sleep Timer - Lets you set the sleep timer so the television automatically switches off after a set amount of
time. Off -> 10min -> 20min -> 30min -> 60min -> 90min -> 120min -> 180min -> 240min
Auto sleep - Toggle the Function on and off
Auto standby - Set Auto standby between 3 hours, 4 hours and 5 hours ( to turn off this function you must
exit Home Mode in the Picture Menu)
Time Zone - Change your current time zone
20
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:20
12/4/2013 11:30:54 AM
TV Menu Operation
OPTION MENU
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
OSD Language - Allows the user to change the language of the menu.
Audio Languages 1st - This allows the user to set the first preferred audio language.
Audio Languages 2nd - This allows the user to set the second preferred language.
Subtitle Languages 1st - This allows the user to set the first preferred subtitle language.
Subtitle Languages 2nd - This allows the user to set the first preferred subtitle language.
OSD Duration - Lets you adjust the amount of time the On Screen Menu stays on the screen
before disappearing.
Blue Screen - Changes the background when there is no input between clear and a blue background
(Only available on some sources)
Hearing Impaired - This allows the user to turn on the Hearing Impaired function, this produces subtitles
on the screen which provide a description of what is happening during the selected program.
Country - This allows the user to change the Country setting to match where the TV is being operated.
Software Update (OAD) - This allows the user to switch OAD (Over Air Download) on or off.
This is a software update that is available via digital signal.
OAD Tuning - This allows the user to define whether the TV automatically retunes after OAD.
Software Update (USB) - From time to time we may release new firmware to improve the operation of
the television (available to download). This menu lets you install the new software/firmware onto the
television. Further details of how to do this will be issued with the firmware. Contact the helpline or
refer to the ‘product support’ section of the website.
Restore Factory Default Reset Menu System - This resets the menus to factory settings.
Reset TV Channels - This clears all the TV channels from the television.
21
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:21
12/4/2013 11:30:55 AM
TV Menu Operation
LOCK MENU
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Enable Locks - Allows you to lock or unlock the menu. You will be asked to enter a 4 digit password.
Use the ◄ button to quit the password input or use the ► button to clear. Default password is 0000.
Once the system lock menu has been accessed you can choose from the following options
Set Password
Allows you to set the password to access the Lock options
Block Program
Allows you to block specific channels
Parental Guidance
Allows you to set the rating to block certain content based on age information
22
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:22
12/4/2013 11:30:55 AM
PC Settings
PC SETTINGS
AV
AV
To access this menu, press [MENU] button on the remote control and scroll right.
To enter a menu press [OK]
If you wish to make changes to any of the default settings, use the scroll
buttons.
To confirm any settings press [OK] button. To exit this menu at anytime, press [EXIT] button.
Auto Adjust - Lets you automatically configure the television to be used as a computer monitor
H Offset - Changes the horizontal position of the picture
V Offset - Changes the vertical position of the picture
Size - Increase picture size
Phase - To adjust delay time of phase in order to reduce the noise of picture
Position Reset - Changes back to the original settings
Tip: If the computer is left in-active for a period of time, the television will switch into a ‘sleep’ state
(the screen will power off to save power). To switch back on press the standby button.
23
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:23
12/4/2013 11:30:55 AM
7 Day TV Guide
7 DAY TV GUIDE
TV Guide is available in Digital TV mode. It provides information about forthcoming programmes (where
supported by the freeview or Saorview channel). You can view the start and end time of all programmes
and on all channels for the next 7 days and set reminders.
1) Press [TV GUIDE] the 7 Day TV Guide will appear.
2) Navigate through the menu using
You can now:
Set a reminder by pressing GREEN
View a previous day by pressing YELLOW
View the next day by pressing BLUE
3) Press [EXIT] to exit the 7 day TV Guide.
24
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:24
12/4/2013 11:30:56 AM
DVD Menu Operation
DVD SETUP
(Applies to models with built in DVD player)
To enter this menu please ensure the TV is in DVD source & press [DVD SETUP]
If you wish to make changes to any of the default settings, use the scroll
To confirm any settings press [OK] button.
buttons.
To exit this menu at anytime, press [DVD SETUP] button.
TV Display - Choose from the following options
4:3 Pan scan
PS Traditional picture format, often used on old film
4:3 Letter box
LB Traditional picture which has been adapted for widescreen
Wide
16:9 Widescreen picture format
Speaker Setup - Choose from the following options
LT/RT
Converts from multi-channel sound to mono
Stereo
Converts from multi-channel sound to stereo
Dual Mono - Choose from the following options
Stereo
Outputs 2 channels of sound both left and right
Mono L
Outputs left side sound
Mono R
Outputs right side sound
Mix Mono
Outputs a single channel of sound but mix between right and left
Dynamic Range - This is the difference between the quietest and loudest sounds. This setting works only
with DVD discs recorded in Dolby digital.
Full
Set this to listen with the range recorded on the disc
3/4
Set this to listen with a range equivalent to a normal television
1/2
Set this to listen with a smaller difference between the maximum and minimum volume
1/4
Set this to listen with a smaller difference between the maximum and minimum volume
Off
Set dynamic range to off
Tip: This TV/DVD player is pre-set to play Region 2 DVDs. In the event you wish to use the TV/DVD
in another country that uses different region discs, please visit www.umc-uk.co.uk. Select ‘Product
Support’, ‘Changing Region’.
25
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:25
12/4/2013 11:31:02 AM
USB Mode / Media Player
USB MODE / MEDIA PLAYER
USB mode offers playback of various different types of content that you have saved on your USB Memory
Stick.
On switching to USB source the above menu screen will appear. The content will be divided into Photo,
Music, Movie and Text based on file type.
1) You can navigate through the menus using the
buttons. To confirm the item you
scroll
wish to play/view press [OK] button.
2) Select the drive you require. (If your drive only
has 1 partition you will only see 1 item).
3) You can now access the item. Press OK to view.
4) While viewing you control the item using
and (OK)
or by pressing ( i ) and using
Tip: If you experience a playback issue, please ensure the files being used are the correct format
(example - the picture plays but no sound) See technical specification page for compatible file types
26
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:26
12/4/2013 11:31:02 AM
General Information
USING YOUR TV WITH A SKY DIGITAL SET TOP BOX
Option 1) Connecting your TV to your Sky box (when both the TV and Sky Box are located
in the same room)
Depending on your Sky Box & TV model, connect either by SCART or HDMI cables
(available separately)
If connecting by SCART, select the ‘Input source’ on the TV as SCART.
If connecting by HDMI, select the ‘Input source’ on the TV as HDMI (if the TV has more
than 1 HDMI port, ensure you select the input source to match the HDMI numbered port
on the rear of the TV)
If you wish to use your Sky remote to operate the TV’s functions, you will need a Sky
remote control (Revision 9 or later) and you will need to programme a 4 digit code into it.
See bottom of this page.
SCART
or HDMI
cable
Sky Box
Option 2) Connecting your TV to your Sky box (when your Sky box is located in a different
room to the TV)
Please note, if you are adding a ‘Magic
Eye/TV Link’ to your system so that
you can use your Sky remote control
to change the Sky channel in the room
where the 2nd TV is located, please
refer to the instructions included
with the TV link/magic eye in order to
ensure the RF or RF2 output on your
Sky box is powered on. (The red LED
light on the TV link/magic eye will light
up if the RF / RF2 output is correctly set
up) If you do not have the instructions
that came with the TV link/magic eye,
instructions on how to do it can be
found on our web site.
2nd TV in
another room
Connect to the
Aerial/RF input
on the 2nd TV
SCART
or HDMI
cable
RF/COAX cable from
Sky Box to 2nd TV
Sky Box
Connect to RF
or RF2 output
on the Sky box
TV Link/Magic Eye
(optional)
1) To tune the TV to the Sky box, on the 2nd TV, select the ‘Analogue’ input source.
2) Select the channel that you wish to store the Sky box/channel on. (If you do not use channels 1-5 because you
no longer have analogue terrestrial channels after digital switchover, you may choose to select channel 1 to store
the Sky box/channel, if you still have and use analogue channels 1-5, you may for example decide that channel 6 is
the best option for you)
3) Press the corresponding number on the remote control to select the desired analogue channel chosen as per
point 2 above.
4) On the TV remote control, press Menu. Now navigate through the menus to select Manual Tuning or Analogue
Manual tuning (refer to the Tuning/Channel menu section of this user guide if necessary)
5) Manually tune in the channel (usually, the Sky box is at a frequency between 800Mhz and 850Mhz) once the
Sky box/channel is found, press ‘OK’ to store it.
If you wish to use your Sky remote to operate the TV’s functions, you will need a Sky remote control (Revision 9 or
later) and you will need to programme a 4 digit code into it. See below.
Using a Sky Remote or a Universal Remote to operate your TV
Sky Remote Control - If you wish to use your Sky remote to operate the basic functions of your TV, you need to
programme a 4 digit code into it. Please note - you will need the latest Sky Revision 9 remote control as this is
the only version that includes the latest software/firmware necessary to operate this model of TV.
The code required for this television is 2134. If you wish to upgrade/replace your existing Sky remote control to
the latest version, you can do so on our web site.
Universal Remote Control - If you wish to use a Universal remote control to operate your TV, please refer to the
website for a full list of codes. (Please note we only have codes for One for All branded remote controls, if you
have an alternative brand of Universal remote, please refer to the manufacturer for the code.)
27
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:27
12/4/2013 11:31:03 AM
General Information
FREQUENTLY ASKED QUESTIONS
General
I would like to have louder
sound by connecting
additional speakers
1) Use the 3.5mm headphone output and a 3.5mm to phono cable
(available separately) to connect to an amplifier/surround sound system.
Please note this will deactivate the TV’s built in speakers.
2) Connect a COAX cable from the TV’s COAX output to your
amplifier/surround systems COAX input.
General
Why are some options in
the menu unavailable and
greyed out
Some options are only available in certain sources, i.e. HDMI. They are
unavailable in the other sources where they have no affect.
General
Can I stop my TV automatically
turning off after 4hrs?
Yes
1) In the picture settings menu, de-select Home Mode.
2) In the time settings menu, scroll down to Auto standby and select OFF.
TV
I have tuned in Digital TV
but I am not receiving any
or all of the channels and/
or the channels I receive are
breaking up
1) Check you are in an area that can receive Saorview.
Visit www.saorview.co.uk
2) Check you are using an aerial that is able to receive a good digital
signal. In most cases, you will need an outdoor digital hi-gain/wideband
aerial. In areas that have excellent digital coverage, you may be able
to use a loft type aerial but it is highly likely that you will also need to
connect a booster between the back of the TV and the TV aerial wall
socket. Unfortunately, to receive a good enough digital signal, it is not
possible to use a portable/indoor type aerial.
TV
I have re-tuned my television
but when I switch it off it is
not storing the channels
Complete a first time installation, please refer to the set-up menu section
of the manual of how to do this.
VCR/DVD
Recorder
I have connected the TV to
my VCR or DVD Recorder via
SCART but it is not recording
In addition to connecting via SCART, you should connect the aerial cable
from the wall socket to your VCR/DVD Recorder and another aerial cable
from the VCR/DVD Recorder to the TV.
DVD
I have inserted a disc but it is
not playing
1) Ensure you have inserted the disc facing the correct way.
2) Ensure the disc is clean and is not scratched.
3) Some copied discs will not play.
4) Check the DVD is a region 2 disc – to change the region of the DVD
player, refer to www.umc-uk.co.uk select ‘product support’, ‘changing
region’.
DVD
I have pressed the eject
button but the disc is not
coming out
To eject the disc hold the stop/eject button for 4 seconds.
Game Consoles
I have connected my PS3 to
the TV via HDMI, but I am
not receiving any pictures or
sound on my Television
1) Ensure the TVs source is on HDMI.
2) Check your settings on your PS3 are as per the PS3 instruction manual.
Game Consoles
I have connected my
Xbox 360 to the TV via
Component Cables (Red,
Green & Blue) but I am not
receiving any sound
Component cables only provide HD Pictures. For the sound you will need
to connect the Red & White audio cables on the Xbox to the Red & White
phono inputs on the rear of the TV. Please refer to the ‘Connections’
pages.
USB Mode
I have inserted a USB
Memory Key, but the TV
does not recognise it
Ensure the USB Memory Key is formatted to type FAT32.
USB Mode
Using a USB portable hard
drive / larger than 32GB
If you wish to use a portable hard drive larger than 32GB, please note
that it must be formatted to the FAT32 file system in order to operate on
this TV. Windows XP/Vista computers are only capable of formatting up
to 32GB, therefore, you will need a software programme/utility to format
larger hard drives. Please refer to the web site for more information.
System Lock
I have changed the password
on the television and now
forgotten it
There is a master password of 4711, to gain access to the TV menu and
reset the normal password.
28
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:28
12/4/2013 11:31:04 AM
General Information
TECHNICAL SPECIFICATION
Model
23/194J-GB-4B-HCU
23/194J-GB-4B-HCDU
Screen size
(diagonal)
23"/ 58cm
RF
75 ohm Antenna / PAL-SECAM
Video Inputs
2 x HDMI , 1 x SCART, 1 x USB, 1 x Video/Composite,
1 x PC/VGA input, 1 x Component (YPbPr)
Sound Inputs
1 x 3.5 mm jack for PC audio input
Sound Outputs
1 x Coax Audio output,
1 x 3.5mm Headphone output
Sound power,
watts (RMS)
Voltage and power
consumption
2 x 3W
110-240V 50/60Hz
20/40W (home mode/max)
in standby less than 0.5w
Dimensions including
stand (mm)
110-240V 50/60Hz
20/50W (home mode/max)
in standby less than 0.5w
567W x 405H x 195D
Annual Energy
Consumption
29 kWh
29 kWh
A
A
3.6
3.9
Energy Rating (EEI)
Net weight (Kgs)
Wall Mounting
VESA 100 x 100
Compatible files in USB Mode
Media
File Ext.
Codec
Video
Movie
Music
Picture
Audio
.mpg
Mpeg-1, Mpeg-2
.avi
Xvid, MJPEG,
MPEG-4 SP/ASP
.ts
Mpeg-2
.dat
Mpeg-1
.mp4
Mpeg-1, Mpeg-2
.vob
Mpeg-2
.mp3
-
.wma
-
Max Resolution: 1920x1080
Max Data rate: 40Mbps
MP3, WMA
Max Resolution: 1920x1080
Max Data rate: 40Mbps
Max Resolution: 1024x768
Max Data rate: 40Mbps
MP3
WMA
Sample Rate 16K-48KHz
Bit rate: 32K - 442Kbps
.jpg
Progressive JPEG
Max Resolution: 1024x768
.jpeg
Baseline JPEG
Max Resolution: 8192x8192
.bmp
BMP
Max Resolution: 6500x6500
29
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:29
12/4/2013 11:31:04 AM
User Guide - BLA-MAN-0169 - 23-194J-GB-4B-HCU-ROI, 23-194J-GB-4B-HCDU-ROI.indd Sec1:32
12/4/2013 11:31:04 AM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising