Craftsman | 315.111810 | Owner`s manual | Craftsman 315.111810 Owner`s manual

Owner's Manual
CRRFTSMRN
°
Single Speed / Reversible
CORDLESS SCREWDRIVER
Model No.
315.111810
Save this manual for
future reference
CAUTION:
Read and
follow all Safety Rules
Operating Instructions
before first use of this
product.
anlLIBRARY:.
Sears,
Roebuck and Co., I-LO_llan Estates, I_._S,_'
972000-446
9-97
!
•
•
•
Table Of Contents ................................................................................................................................ _._.._....2
Warranty .........................................................................................................................................................
2
Introductionand ProductSpecifications.........................................................................................................
2
•
Rules For Safe Operation ...........................................................................................................................
•
•
A. ImportantSafety Rules For Battery Tools .............................................................................................. 4
B. Important Safety InstructionsFor Charger .......................................................................................... 4-5
Accessodes ....................................................................................................................................................
5
Features .........................................................................................................................................................
6
•
•
Operation.....................................................................................................................................................
Maintenance .................................................................................................................................................
7-9
10
•
Battery Removal ...........................................................................................................................................
11
•
•
A. Battery Removal, Preparation For Recycling....................................................................................... 11
Replacement Parts ................................................................................. .:.................................................... 11
Parts Ordering / Service ...............................................................................................................................
12
3-5
FULL ONE YEAR WARRANTY ON CRAFTSMAN CORDLESS SCREWDRIVER
If this CRAFTSNAN Cordless Screwdriver fails to give complete satisfactionwithin one year from the date of
purchase, RETURN IT TO THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears will replace it,
free of charge.
If this rRAFlrSNRN Cordless Screwdriver iSused for commemial or rental purposes,this warrantyapplies for
only 90 days from the date of purchase,
This warranty gives you specific legal rights,and you may also have other rightswhich vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
Yourscrewdriver has many features for making
driving operations more pleasant and enjoyable.
Safety, performance and dependabilityhave been
given top priorityin the design of this screwdriver
making it easy to maintain and operate.
CAUTION: Carefully read throughthis entire
owner's manual before usingyour new
screwdriver. Pay close attention to the Rules For
Safe Operation, Warnings and Cautions. If you
use your screwdriver properly and only for what it
is intended, you will enjoy years of safe, reliable
SPECIFICATIONS:
Collet
Motor
1/4 in.
2.4 Volts DC
Charger Rating
120 Volts,60 Hz, AC Only
No Load Speed
Switch
165 RPM
Single Speed - Reversible
Charge Rate
3-5 Hours
tl_._;_J
20 in. Lbs.
,_-Look
for this symbol to point out important safely Precautions. It means attention!!! Your
_Pf_e]yJsjnvolved ....
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and
the explanations wlth them, deserve your careful attention and understanding, The safety wamlngs do _
not by themselves ellmlnate any danger. The Instructions or warnings they give are not substltutes for
proper accident prevention measures.
SYMBOL
A
MEANING
SAFETY ALERT SYMBOL:
Indicatescautionor warning.Maybe usedin conjunction
withothersymbolsor pictographs.
A
WARNING: Failureto obey a safety warning can resultin seriousinjuryto yourself or to others.
Always follow the safety precautionsto reduce the dskof fire, electric shock and personal injury.
A
CAUTION: Failureto obey a safety warning may result in propertydamage or personalinjuryto
yourself or to others. Always follow the safety precautionsto reduce_thedsk of fire, electdc shock
and personalinjury.
NOTE:
_k
Advises you of informationor instructionsvital to the operationor maintenance of the equipment._-" *-
WARNING: Do not attempt to operate this tool
until you have read thoroughlyand understand
completely all instructions,safety rules, etc.
contained in this manual. Failure to comply can
result in accidents involvingfire, electric shock,
•
USE RIGHT TOOL Don't force small tool or
attachment to do the job of a heavy duty tool.
Don't usa tool for purposenot intended - for
example - A circular saw should never be used
for cuttingtree limbs or logs.
or sedous personal injury. Save owner's manual
and review frequently for continuingsafe
operation, and instructingothers who may use
this tool.
•
WEAR PROPER APPAREL. Do not wear loose
clothing or jewelry that can get caught in tool's
movingparts and cause personal injury. Rubber
glovesand nonskidfootwear are recommended
when workingoutdoors. Wear protectivehair
coveringto contain long hair and keep it from
being drawn into nearby air vents.
READ ALL INSTRUCTIONS
KNOW YOUR POWER
TOOL.
Read owner's
manual carefully. Learn its applications and
limitations as well as the specific potential
hazards related to this tool.
ALWAYS WEAR SAFETY GLASSES.
eyeglasses have only impact-resistant
they are NOT safety glasses,
GUARD AGAINST ELECTRICAL SHOCK by
preventing body contact with grounded surfaces.
For example: Pipes, radiators,ranges, refrigerator enclosures.
•
PROTECT YOUR LUNGS. Wear a face mask or
dust mask if operation is dusty.
PROTECT YOUR HEARING. Wear headng
protectionduring extended periods of operation.
KEEP WORK AREA CLEAN. Cluttered areas
and benches invite accidents.
SECURE WORK. Use clamps or a vise to hold
work. It'ssafer than using your hand and it frees
both hands to operate tool.
AVOID DANGEROUS ENVIRONMENT. Don't
use power tool in damp or wet locations or
expose to rain. Keep work area well lit.
DON'T OVERREACH.
Keep proper footing and
balance at all times. Do not use on a ladder or
KEEP CHILDREN AND VISITORS AWAY. All
visitorsshouldwear safety glasses and be kept a
safe distance from work area. Do not let visitors
contact tool or extension cord.
unstable supped.
MAINTAIN TOOLS WITH CARE. Keep tools
sharp at all times, and clean for best and safest
performance. Follow instructions for lubricating
and changing accessories.
STORE IDLE TOOLS. When not in use tools
should be stored in a dry and high or locked-up
place - out of the reach of children.
DON'T FORCE
TOOL.
Everyday
lenses;
REMOVE ADJUSTING
KEYS AND
WRENCHES.
Form habit of checking to see that
It will do the job better
keys and adjusting wrenches are removed
tool before turning it on
and safer at the rate for which it was designed.
3
from
g
RULES
FORSAFEOPERATION
(Continued)
NEVER
USE IN AN EXPLOSIVE
DO NOT PLACE BATTERY TOOLS OR THEIR
BATTERIES NEAR FIRE OR HEAT. Theymay
explode.
ATMO-
SPHERE. Normal sparking of the motor could
ignite flammable liquids, gases, or fumes.
DO NOT CHARGE BA'FrERY TOOL IN A
DAMP OR WET LOCATION.
KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based productsor any
strong solventsto clean your tool
Your battery tool should be charged in a location
where the temperature is more than 50°F but
less than 100°F.
STAY ALERT. Watch what you are doing and
use common sense. Do not operate tool when
you are tired. Do not rush.
CHECK
DAMAGED
PARTS.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquidcomes in
contactwith your skin, wash immediatelywith
soap and water, then neutralize with lemon juice
or vinegar. If liquidgets in your eyes, flush them
with clean water for at least 10 minutes, then
seek immediate medical attention.
Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Chock for alignment of moving pads,
binding of moving pads, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced by an authorized service center unless
indicated elsewhere in this instruction manual.
DO NOT USE TOOL IF SWITCH
TURN
if carryingyour battery tool at your side, make
sure it is not running and your finger is not__
on the
switch. Avoid accidental starting.
SECURE WORK before applying power, NEVER
hold workpiece in your hand or across your legs.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS,
DOI_S NOT
IT ON AND OFF. Have defective switches
replaced by an authorized service center.
IMPORTANT
CHARGER
DRUGS, ALCOHOL, MEDICATION.
Do not
operate tool while under the influence of drugs,
alcohol, or any medication.
•
DRIVING
SCREWS
INTO ELECTRICAL
WIRING IN WALLS, CEILINGS, OR OTHER
AREAS CAN CAUSE THE SCREWDRIVER
BIT
OR COLLET TO BECOME ELECTRICALLY
•
INSPECT
IMPORTANT SAFETY RULES FOR BATTERY
TOOLS
Battery tools do not have to be plugged intoan
electrical outlet; therefore, they are always in
operating condition.Be aware of possible
hazards when not using your battery tool or
when changing accessories.
USE ONLY THE CHARGER PROVIDED WITH
YOUR BATTERY TOOL. Do notsubstituteany
other charger. Use of another charger could
cause batteries to explode causing possible
serious injury.
FOR
SAVE THESE INSTRUCTIONS. This manual
contains importantsafety and operating
instructionsfor battery charger part number
999555-001.
_k
WARNING: To reduce riskof injury,charge only
nickel-cadmiumtype rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
m
Do not expose charger to rain or snow.
FOR and remove all nails from lumber
before driving screws.
INSTRUCTIONS
Before usingbattery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger,
LIVE. Do not touch metal parts when driving
screws into a wall; grasp only the insulated
handle(s) or plastic housing when using this tool.
Make sure hidden electrical wiring, water pipes,
and mechanical hazards are not in the path of
the bit when driving screws into a wall.
SAFETY
Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a riskof fire, electric shock, or injuryto
persons.
To reduce risk of damage to charger body and
cord, pullby charger body rather than cordwhen
disconnectingcharger.
Make sure cord is located so that it will net be
stepped on, tripped over, or otherwisesubjected
to damage or stress.
RULES
FORSAFEOPERATION
(Continued)
Anextension
cordshould
notbeusedunless
absolutely
necessary,
Useofimproper
extension
cordcouldresult
inariskoffireand
electric
shock.
Ifextension
cord must be used,
Do not operate charger if it has received a
sharp blow, been dropped, or othen,#ise
damaged in any way; take it to a qualified
serviceman.
make sure:
a.
Do not disassemble charger; take it to a
qualified serviceman when service or repairis
required, Incorrectreassembly may resultin a
dsk of electric shock or fire.
That pinson plug of extensioncord are the
same number, size and shape as those of
plug on charger.
b. That extensioncord is properly wired and in
good eiactdcalcondition; and
c.
That wire size is large enough for AC
ampere ratingof charger as specified
below:
Cord Length(Feet) 25ft.
5Oft.
100ft.
Cord Size (AWG) 16
16
16
Note: AWG = American Wire Gage
•
150ft.
To reduce risk of electdc shock, unplugcharger
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
•
•
14
Do not use charger outdoors.
Disconnectcharger from power supplywhen
not in use.
SAVE THESE INSTRUCTIONS. Refer to them
frequentlyand use-them to instructotherswho
may use thistool, If you loan someone this tool,
loan them these instructionsalso,
DO NOT OPERATE CHARGER WITH A
DAMAGED CORD OR PLUG. If damaged, have
replacedimmediatelyby a qualifiedserviceman.
_1= WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage, Before beginning power tool operation, always wear
safety goggles or safety glasses with side shields and a full face shield when needed, We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses
with side shields, avaiEable at Sears Retail Stores.
,_
WARNING:
Do not allow familiarity with your
screwdriver to make you careless, Remember
that a careless fraction of a second is sufficient to
inflict severe injury.
,_
CAUTION: Your screwdriver contains special
high temperature batteriesto help prevent
battery damage when left on charge for extended
periods of time. However, once the batteries
become fully charged, we recommendthat you
unplug yourcharger from power supply and
disconnectit from scrswddver.
The fo ow ng recommended accessories are_urrently available at Sears Retail Stores.
No, 2 Phillips/ 8-10 Slotted,2 Ea.
No. 3 Phillips/ 6-8 Slotted, 2 Ea.
5-Pc. Hex Shank Drill BitSet
6-Pc. Extra Length Screwdriver Bit Set
"/-Pc. Screwdriver Bit Set and Case
_.
WARNING:
13-Pc. Power Screwdriver / Nutdriver Set and
Case
30-Pc. Power Scrawddver/Nutdriver Set and
Case
17-Pc, Power Screwdriver/Nutdriver Set and
Case
The use of attachments or accessories not listed mightbe hazardous,
KNOW YOUR SCREWDRIVER
See Figure 1.
Before attempting to use your screwdriver, familiadze
yourself with all operating features and safety
requirements.
WARNING: If any parts are missing,do_01"
operate tool until the missingparts are replaced.
Failure to do so could result in possibleserious
personal injury.
_EWOFSCREWDRIVERIN OPERA_NG PosmoN
FORWARD(_
REVERSE_)SWITCH
FORWARD
REVERSE
CENTER
POSITION_OCK)
WRISTSTRAP
ADJUSTMENT CAP
VIEW OF SCREWDRIVER IN UPSIDE DOWN POSITION
SWITCHTRIGGER
LIGHTSWITCH
UGHT
ENDCAP
WlTHEXTRA
BULBSTORAGE
Fig. 1
LIGHT
WRIST
As shown in figure 1, your screwdriver has been
designed with a light. This feature is convenientwhen
workingin close or tight areas where additional light is
needed.
See Figure 1.
A wrist strap is provided to reduce the chances of
droppingyour screwdriver. Place one hand through
the wrist strap when carryingtool,
STRAP
CHARGING YOUR SCREWDRIVER
Your screwdriver has been shipped in a low charge
condition to prevent possible problems. Therefore,
you should charge it at least 3 hours prior to use.
Note: Batteries will not reach ful! charge the first time
they are charged. Allow several cycles (driving
screws followed by recharging) for them to become
fully charged.
If the charger does not charge your screwdriver under
normal circumstances, return both the screwdriver
and charger to your nearest Sears repair center for
electrical check.
CHARGING
STAND
See Figure2.
2-3/8 in.
PILOTHOLES
CHARGING
.s
BACK SIDE OF CHARGING STAND
•
Fig. 3
Locate close to an electrical outlet.
Note: Temporarily place your screwdriver in
charging stand. Check to make sure it will not
interfere with the charger or electrical outlet.
SCREWS
WALL
ANCHORS
CHARGE
UGHT(LED)
BR
STORAGE
AREA
BIT
CHARGER
•
Drill two (2) pilot holes then insert the two (2)
wall anchors provided.
Note: Pilot holes should be 2-3/8 inches apart.
See Figure 3.
•
Position charging stand on wall aligning holes in
charging stand with pilot holes.
•
Secure charging stand with the two (2) screws
provided.
TO CHARGE
•
Place the forward/reverse switch in center
position.
•
Place screwdriver in chargingstand.
Note: Screwdrivermust be in charging stand to be
charged.
•
Insert charger plug into inputjack making sure
they are propertyconnected.
Charger can be used with normal house
voltage of 120 volts, 60 Hz, AC only.
BO'I'rOMOF
CHARGING STAND
INPUT
•
•
Connect charger to power supply.
•
The charge indicatorlight(LED) indicator, which is
located on the charging stand, will light up when
charger is propedy connected to power supply.
This red light indicatesyour screwdriveris charging and will remain on untilcharger is disconnected from power supply.
After normal usage, a minimumof 3 hours of
chargingtime is required to be fully charged.
CHARGERPLUG
Fig. 2
For storage convenience,a charging stand with bit
storage has been providedwith your screwdriver. It
has the capacity of storingyour screwdriver and two
(2) bitswhich are also included with your screwdriver.
TO MOUNT CHARGING
See Figures 2 and 3.
STAND
•
•
DO NOT place charger in an area of extreme heat
or cold. It works best at normal room temperature.
SWITCH
See Figure 4,
To turn your screwdriverON, depress switch triggerin
the direction of the arrow in figure 4. To turn it OFF,
release the switch tdgger.
Your screwdriver is equipped with a Forward/litllmrse
Switch which allows you to change the direction of
rotationof the bit. For ddvingor forward rotation,slide
the switch to the forward(F) position.To reversethe
bit direction, slide the switch to the reverse(R)
position.
CAUTION: To prevent gear damage, always
allow bit to come to a complete stop before
changing the directionof bit mtation.
To stop your screwdriver, release switch tdggerand
allow your screwdriver to come to a complete stop.
SWITCH LOCK
See Figure 5.
Fig. 4
REVERSIBLE
See Figure5.
REVERSE(R)
The switch trigger can be lockedin the OFF position.
This feature can be used to prevent the pessi_"ity of
accidental startingwhen not in use. To lock switch
tdgger, place the forward/reverse switch in center
position.
_
WARNING: Battery tools are always in
operatingcondition. Therefore, switchshould
always be locked when not in usa or carrying at
your side.
_
WARNING:
Always wear safety goggles or
safety glasses with side shields when operating
tools. Failure to do so could result in objects
being thrown into your eyes, resulting in possible
serious injury.
FORWARD(_
CENTER
PosmoN
FORWARD(_
REVERSE(R)
SWITCH
(LOC_
Fig. 5
COLLET
Thecollet
onyourscrewdriver
hasbeendesigned
to
accept
1/4in,hoxbits.See Figure 6,
When usingyour screwdriverfor various driving
applications,it becomes necessary to increase or
decrease the power and torque in order to help
prevent the possibilityof damaging screwheads,
threads, workpiece, etc. In general, power and torque
shouldcorrespond to the difficultyof the screw to be
ddven. If torque is too high the screws may be
damaged or broken.
Note: Your screwdriver has been shipped with the
adjustable torque clutch set at the lowest torque
setting.
COLLET
\
TO ADJUST
See Figure 7.
•
•
Fig. 6
TO INSERT BIT
See Figure 6.
•
•
•
Lock switch tdgger by placing the forward/reverse
switch in center position. See Figure 5.
Insert bit into collet as far as possible,
When finished usingyour screwdriver, remove bit
from collet and place it in charging standfor
storage. See Figure 2.
I
I
BITSINCLUDED WITH CORDLESS SCREWDRIVER I
Double-ended Bit (#1 Phillipsand #5 Slotted)
Double-ended Bit (#2 Phillipsand #7 Slotted)
I
ADJUSTABLE
TORQUE
CLUTCH
(Tightening Power of Your Screwdriver)
See Figure
TO
INCREASETOROUE
Locate arrow on torque adjustmentcap.
To increase torque, rotate torque adjustmentcap
in the directionof the arrow, When cap stops
rotating,you have reached the highest torquesetting.To decrease torque, rotatetorque adjustment cap in the oppositedirection of the arrow.
When cap stops rotating,you have reached the
lowest torque setting.
BATrERIES
Your scrowddver is equipped with 2 nickel-cadmium
rechargeable batteries. Length of servicefrom each
chargingwill depend on the type of work you are
doing.
The batteries in thistool have been designed to
provide maximum trouble free life, However, like all
batteries, they will eventually wear out. To remove
batteries, see page 11, Battery Removal. Handling of
these batteries, especially when wearing dngs and
jewelry, could result in a serious burn,
To obtain the longest possiblebattery life, we suggest
the following:
•
Store and charge your batteries in a cool area.
Temperatures above normal room temperature
will shorten battery life.
•
Never store batteries in a discharged condition.
Recharge them immediately after they are discharged.
•
All batteries gradually lose their charge. The
higher the temperature, the quicker they lose their
charge. If you store your toolfor long periods of
time without usingit, recharge the batteriesevery
month or two. This practice will prolong battery
life.
J
TO
DECREASE
TORQUE
ADJUSTMENT
TORQUE
CAP
Fig. 7
TORQUE
_,
,_
Remove old bulb by lifting it from socket.
WARNING: When servicing,use only identical
Craftsman replacement parts. Use of any other
part may create a hazard or cause product
damage.
For your convemence, a bulb storage area with an
extra bulb has been provided. It is located inside
the end cap on the bottom of your screwdriver.
See Figure 9.
WARNING: Donot at any time let brake fluids,
gasoline, petroleum-based products,penetrating
oils, etc. come in contact with plastic parts. They
contain chemicals that can damage, weaken or
destroy plastic.
BULB
STORAGE
AREA
TO REMOVE
ENDCAP
Only the partsshown on parts list, page 11, are
intended to be repaired or replaced by the customer•
All other parts shouldbe replaced by a qualified
service technician at an authorized servicefacility.
Avoid usingsolvents when cleaning plasticparts.
Most plastics are susceptible to damage from various
types of commercial solvents and may be damaged
by their use. Use clean clothsto remove dirt, dust, oil,
grease, etc.
MOTOR
HOUSING
EXTRA
BULB
DO NOT ABUSE POWER TOOLS. Abusive practices
can damage tool as well as workpiece.
_k
•
WARNING: Do not attempt to modifythis tool or
create accessories not recommended for use
with thistool•Any such alteration or modification
is misuse and could result in a hazardous
condition leading to possibleserious personal
injury.
BULB
REPLACEMENT
See Figures 8 and 9.
•
Loci< switch trigger by placing the forward/reverse
switch in center position.
•
Remove bulb cover.
Note: Depress bulb cover and slide forward as
shown by the arrows in figure 8 to remove.
SUDEFORWARD
DEPRESS
HERE
BULB
COVER
BULB
\
SOCKET
Fig. 8
10
TO REPLACE
ENDCAP
END
CAP
Fig. 9
•
Remove end cap by twistingit in the directionof
the arrow as shownin figure 9.
Position new bulb in socket.
•
Replace bulb cover by insertingtab into slot.
•
Replace end cap.
MOTOR
HOU_NG
To
preservenaturalresources,please
recycleor
disposeof expiredbatteries
This productcontains nickel-cadmium
battery. Must be disposed of properly.
TOREMOVE
ENDCAP
Local, state, or federal laws may prohibitdisposalof
nickel-cadmiumbatteries in ordinary trash.
Consultyour localwaste authorityfor information
regarding available recyclingand/or disposaloptions.
BATTERY REMOVAL, PREPARATION
RECYCLING
See Rgurel_
TO REMOVE:
•
•
•
_k
FOR
TO REPLACE
END CAP
Lock switchtdgger by placing the forward/reverse
switch in center position.See Figure 5.
Remove end cap securing batteriesby twistingit
in the direction of the arrow as shown in figure 10.
END CAP
BAKERY
LEADS
Slide batteriesfrom motor housing enough to
expose leads and battery terminals. Disconnect
leads from battery terminals. Note where each
lead connects to battery terminals. Connection
must be identicalwhen installing new batteries.
Note: Be careful notto break battery terminals
when disconnectingleads.
BA'I'rERY
TERMINAL
WARNING:
Upon removal, cover the battery's
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of
properly. Also, never touch both terminals with
metal objects and/or body parts as short circuit
may result, Keep away from children. Failure to
comply with these warnings coutd result in fire
and/or serious injury,
WHEN SERVICING,
Key
No.
TERMINAL
BATTERIES
Fig. 10
USE ONLY IDENTICAL
Part
Number
Description
1
2
974277-003
999555-001
Battery Pack .
Battery Charger
3
974385-002
972000-446
Charging Stand
Owner's Manual
11
CRAFTSMAN
REPLACEMENT
PARTS
H
Forthe repairor replacementpartsyouneed
delivereddirectlyto yourhome
Call 7 am - 7 pm, 7 days a week
1-800-366-PART
(1-800-366-7278)
Forrepairservice
Call24 hoursa day,7 daysa week
1-800-4-REPAIR
(1-800-473-7247)
Forthe locationof a
SearsPartsandRepairCenterinyourarea
Call24 hours a day,7 days a week
1-800-488-1
222
imiii|
The modelnumberof thistool will be foundon a serial plate
attachedto the motorhousing.Whenrequestingserviceor
order!ngparts,alwaysprovidethe followinginformation:
• Product Name
Cordless
Screwdriver
•
Model Number
315.111810
• PartName
• Part Number
SEARS
America's
RepairSpecia/ists
Download PDF

advertising