Canon Digital Rebel - EOS 6.3MP Digital Rebel Camera Specifications

Canon Digital Rebel - EOS 6.3MP Digital Rebel Camera Specifications
Table of Contents
Newly Developed 10.1 MP Sensor
Comprehensive Dust Reduction System
New 9-point AF System
New 2.5-in. TFT LCD Screen
Display-off Sensor
New User Interface
Basic Operation Concept
New Info Display Items
SET Button, Cross-Keys, DISP.
Improvements to Playback
Picture Style
Custom Functions
Camera Direct Printing
Direct Image Transfer
Design and Construction
Drive and Power Source
Accessories and System Compatibility
Contents ©2006 by Canon U.S.A., Inc. All Rights Reserved. Excerpts from this material may be quoted in
published product reviews and articles. For further information, please contact Canon U.S.A., Inc. Public
Relations Dept., (516) 328-5000.
The Canon EOS Digital Rebel XTi is the best entry-level digital single lens reflex (DSLR)
camera on the market today. Compared with its competitors at the sub-$1000 price
point, lens included, the XTi produces the finest images with the purest colors and the
lowest noise, and has the most comprehensive solution to the problem of dust on the
sensor. It also has the clearest and most elegant user interface, the fastest and most
precise autofocus, and the most powerful and useful software package.
The original Canon EOS Digital Rebel, introduced in September, 2003, was the first
interchangeable lens DSLR marketed for less than $1000 including a lens, the EF-S
18-55 mm zoom. Purchasers were delighted to find the camera small, light and easy to
handle. Its image quality was remarkable thanks to its high-quality Canon CMOS sensor,
producing lower noise levels than more expensive rival products offered. The original
Digital Rebel enjoyed immense success in the marketplace, selling more than 1.2 million units worldwide in less than 18 months. In March, 2005, Canon introduced the
second generation Digital Rebel XT with an 8.0 megapixel CMOS sensor vs. the 6.3 MP
CMOS sensor of the Digital Rebel. The new camera was 3 ounces lighter and a half inch
smaller than the original. A newly-developed DIGIC II image processor made the XT
much faster, yet more frugal with battery power. E-TTL II flash control , nine Custom
Functions, White Balance Bracketing, long-exposure noise reduction, a monochrome
mode and a host of other changes gave XT users tremendous control over the photographic process. It was amazing that Canon could sell this camera for less than $1000,
lens included. Once again, Canon had a wildly successful DSLR.
The new Canon EOS Digital Rebel XTi builds on this inheritance. It uses a new, highly evolved 10.1 megapixel
CMOS sensor that is designed and manufactured
entirely by Canon using equipment which
was also designed and manufactured by
Canon. In this and many other respects,
Canon is unique in the world of photography. Canon’s world-leading R&D division
(second or third globally each year for 14
consecutive years in the number of U.S.
patents granted) sees to it that every
Canon DSLR has the highest image quality and the lowest noise in its category.
• Canon designs, develops and manufactures its own EF lenses, its own CMOS image
sensors, and its own DIGIC image processors, with proprietary technologies that it
doesn’t sell to anyone else.
• Canon’s original EOS Integrated Cleaning System gives the Digital Rebel XTi a comprehensive dust cleaning and management system offered by no other camera at any price.
• The Digital Rebel XTi has a 9-point, high-precision autofocus unit that it shares with
the EOS 30D. The central sensor of the AF unit enhances precision with f/2.8 or faster
lenses, a professional feature exclusive to the XTi in its category.
• The XTi has a new, large, bright, sharp, easy to read 2.5-inch color display and a new
user interface that make the camera a delight to use. Picture Style, an improved Direct
Print function, Print/Share, and a host of other improvements make the Digital Rebel
XTi the highest performing member yet of the Digital Rebel family. The XTi builds on
the successes of its predecessors, each of which was a superstar in its own right.
With the Digital Rebel XTi, Canon goes from strength to strength, adding and refining
features to make the XTi the finest camera today in the under-$1000 category.
• New class-leading 10.1 megapixel Canon CMOS image sensor with improved
microlens array
• Comprehensive EOS Integrated Cleaning System including Self Cleaning Sensor Unit
and Dust Delete Data detection
• Large and bright 2.5 inch, 230,000 pixel LCD screen with wide viewing angle
• New, easy-to-use interface for camera settings with enhanced display information
• Expanded Info screen including RGB histogram and CF card remaining capacity
• Continuous shooting at 3 frames per second, best-in-class burst rate of 27 consecutive
frames JPEG (Large/Fine) or10 RAW frames
• Flexible folder management with manual folder creation and up to 9,999 images
per folder
• Picture Style settings
• High-precision 9-point autofocus unit with f/2.8 support
• Selectable AF modes
• Selectable AF points
• 3 settings for long exposure noise reduction, including auto
• Faster image processing
• Improved Print/Share functions
• Improved Direct Print functions including red-eye correction, face brightening and
index printing
• Convenient image display functions including
computer-only auto rotation and reduce/enlarge
during quick review
• Additional Custom Functions
• Superior software package including Canon’s
exclusive Digital Photo Professional
Newly Developed, HighResolution 10.1 Megapixel
CMOS Sensor
The all-new Canon CMOS sensor in the EOS Digital Rebel
XTi gives this camera the highest overall performance in
its class. Like all other Canon CMOS sensors, this unit is
designed and manufactured by Canon using semiconductor manufacturing equipment which was also designed
and manufactured by Canon. This fully-integrated design
10.1 Megapixel CMOS Sensor
and manufacturing system makes Canon unique in the
photo industry. Canon has now produced over 5 million CMOS sensors, all for use
exclusively in Canon DSLR cameras. The experience this achievement represents, in
addition to constant R&D efforts, has enabled Canon to refine and improve its image
sensors to their current remarkable level.
The image sensor in the Digital Rebel XTi measures 22.2 by 14.8 mm. Each of its 10.1
million pixels measures 5.7 µm square. Its predecessor, the Digital Rebel XT, had 8.0
megapixels, each measuring 6.4 µm square. Several improved technologies help the
XTi to continue the Canon tradition of offering a wide range of ISO settings (100-1600),
all of which are highly usable and characterized by very low noise despite the smaller
pixel size that is a function of higher resolution. First, the spacing between the on-chip
microlenses is now about half of the Digital Rebel XT’s. This new configuration gathers
light much more effectively, loses less light between the microlenses, and improves
light convergence. Second, a higher percentage of each pixel’s surface area is sensitive
to light. Third, the output amplifiers have been optimized, lowering noise. Last, the
second-generation, on-chip noise reduction circuit minimizes random noise and
removes fixed-pattern noise. As a result, the XT and the XTi have the same signal-tonoise ratio and equivalent dynamic ranges despite the smaller pixels of the XTi. Finally,
the 3 frames-per-second continuous shooting speed of
Dichroic mirror
(Reflects infrared rays)
the XT has been maintained notwithstanding the larger
3. Infrared-absorbing glass
file size of the XTi. The combination of two-channel readout from the sensor, increased processor clock speed
and improved performance of the output amps is responsible for this accomplishment.
The infrared-blocking, optical low-pass filter is an integral
part of the sensor package, and is divided into two individual components for the first time. Low-pass filter #1 is
part of the Self Cleaning Sensor Unit. Its front surface is
coated with a dichroic mirror that reflects infrared wavelengths. LPF #1 also separates the subject image into two
4. Low-pass filter 2
(Separates image in
vertical direction)
2. Phaser layer
(Converts linear polarized
light into circular polarized light)
1. Low-pass filter 1
(Separates image in horizontal
images horizontally. The phase plate, or phaser layer, converts the images separated by
LPF #1 from linear polarization to circular polarization and prepares these polarized
components to be correctly separated into four square images by low-pass filter #2. The
hybrid infrared-absorption glass reflects and absorbs infrared light, effectively suppressing red ghosting and color casts caused by reflections on the sensor surface. The subject image divided into two images horizontally by the low-pass filter is separated vertically into two images by low-pass filter #2. The image is thereby properly separated into
four square images. The image separation width for the vertical and horizontal images is
optimized for the sensor pitch, minimizing color artifacts and moire caused by minute
horizontal- and vertical-line patterns. As in the case of the Canon EOS 5D, low-pass filter #2 also serves as the CMOS sensor package's cover glass, eliminating a relatively
expensive glass cover and reducing cost.
Extraordinary New Dust
Reduction System
Most modern camera stores now have a department devoted to dust removal tools:
brushes sized to match sensors, electronic brushes, brushes that spin, solutions- in liquid and tablet form- for cleaning brushes, swabs of many types, wipes, grabbers, sticks,
sleeves, liquids (ethanol, methanol and mysterious agents), rubber bulbs both large
and small, chamber cleaning swabs and solutions, and, of course, more. The reason for
this profusion is that digital SLRs with interchangeable lenses are susceptible to dust
particles entering the camera when the lens is changed. The dust can settle on the sensor and leave a spotty mess on photographs, especially in less variegated areas like
skies and clouds. The dust needs to be removed periodically, but touching a sensor is
regarded (properly) by most people, no matter how skilled or prepared, as something to
be avoided until or unless it is absolutely unavoidable.
In the Digital Rebel XTi, Canon offers an astute new approach to the dust problem: a
self-cleaning sensor unit and Dust Delete Data software. Traditional manual sensor
cleaning remains an option, of necessity, but it now needs to done much, much less
often, if at all, depending on shooting conditions and photographers’ habits. The overall strategy is one of, first, neither generating nor attracting dust. The shutter unit (the
same as in the Digital Rebel XT) generates minimal dust; the body cap (incorporated
since the first half of 2005) is now made of a material which minimizes dust caused by
normal wear and rubbing, and the low-pass filter is treated with an anti-static charge
process to prevent static-charged dust from adhering to it.
In the course of developing this unit, Canon engineers analyzed the
causes, types and sizes of visible dust. The dust becomes most noticeable at small apertures, so they studied what sizes of dust were the
worst offenders at small apertures. The Self Cleaning Sensor Unit was
then designed to eliminate those types of dust most effectively. Lowpass filter #1 on the front of the sensor is attached to an ultrasonic
vibrating unit driven by a piezoelectric element. When LPF #1 is subjected to ultrasonic vibrations, the adhering dust is shaken off the surface.
Piezoelectric element
The removed dust then sticks to an absorbent material ringing the low-pass filter. The
sensor unit also has an internal O-ring around the perimeter to keep out dust. The area
between LPF #1 and the CMOS sensor is thus sealed; dust cannot enter from the side.
Low-pass filter 1
Instead of a dust-removal system which uses a vibrating
glass, the Digital Rebel XTi uses its low-pass filter to
vibrate directly, shaking off dust. Therefore, the optical
performance is not degraded by an extra sheet of glass,
and compactness is maintained. The camera body size is
virtually the same as that of the Digital Rebel XT.
Phaser layer
Infrared-absorbing glass
Low-pass filter 2
Support material
The default setting for the self-cleaning sensor has the
cleaning unit operating for 1 sec. when the camera's
power switch is turned on or off. Dust is therefore
removed before shooting and after shooting is completed,
the latter instance because dust is more difficult to dislodge after it has been stuck for a long time. Self-cleaning
can be enabled or disabled by setting "Clean when the power switch is turned <ON> or
<OFF>" to [Enable] or [Disable]. During self-cleaning operation, the LCD screen displays an
appropriate self-cleaning system logo.
The self-cleaning system can also be activated manually with the menu item [Clean
now]. Note that shooting priority still holds. If you press the shutter button halfway or
press the menu button during the self- cleaning operation (in either the Auto or Manual
modes), the cleaning operation will stop and the camera will be ready to shoot.
Pressing the shutter button during the internal processing startup sequence (immediately after the 0.2 second startup) will make shooting possible at that moment and sensor cleaning will not occur.
Cleaning complete
0.2 sec.
Internal processing
0.5 to 2 seconds
Sensor cleaning
Approximately 1 second
Shooting is possible immediately after startup
During manual cleaning with the reflex mirror locked up, the LCD screen will indicate
that sensor cleaning is in progress. When the battery level is low, the following warnings are given: First, the beeper will sound even if [Beep] is set to [Off]. Second, a warning message is displayed on the LCD screen until the prohibited voltage is reached.
Because the self-cleaning system requires exceptionally
low power, the number of possible shots from a charged
battery is not reduced measurably.
To prevent the piezoelectric element from overheating,
the self-cleaning unit cannot operate for 3 sec. after any
Self Cleaning Sensor Unit
operation. Also, if the self-cleaning unit is operated 5 consecutive times within 10
sec., it will not work for 10 sec. afterward. Turning the power off does not reset this.
The restriction does reset if the cleaning function is not activated for at least 60 seconds. While the self-cleaning unit is disabled, if you select [Sensor cleaning: Auto] from
the menu, the [Clean now] option will be grayed out and cannot be selected.
Two kinds of dust are less likely to be moved by the accelerations of the vibrating LPF:
small and light particles and the dreaded sticky stuff. In the event that the Self Cleaning
Sensor Unit cannot remove all the dust, the Dust Delete Data (the size and position of
dust too small or too sticky to remove with the Self Cleaning Sensor Unit) is obtained and
appended to the image so that Digital Photo Professional Ver. 2.2 can erase the remaining dust spots on the image automatically. The shadows created by the dust particles
adhering to low-pass filter #1 are detected by the imaging sensor. The most troubling
dust particles, mostly the
larger ones, are then sin1
gled out and their location
coordinates are obtained
as Dust Delete Data. This
data is attached to the
image. After the shutter is
released, it takes about 6
sec. to obtain the Dust
Delete Data.
Self-cleaning sensor
system operates.
Steps to obtain dust delete data
To obtain Dust Delete Data, begin by taking a picture of a solid white, patternless object
(such as a piece of white paper) which is quite out of focus despite the use of a small
aperture. Use a 50mm or longer lens with manual focus set to infinity. The object
should be about 1 foot from the camera. Any common light source is fine. Fill the
viewfinder frame. (The image data can be obtained even without a CF card installed in
the camera.) When the screen in step 4 appears, the camera will be set automatically
as follows: shooting mode, aperture-priority AE; aperture, f/22; shutter speed, 1/2 sec.
or faster; ISO Speed, 800***; flash, off; drive mode, single.
Even if the focus mode is set to <AF>, manual focus will still take effect, and even if a CF
card is installed in the camera, the image taken for the dust deletion will not be recorded. If the picture was overexposed or underexposed by 2 stops or more or if the lighting
of the white paper was very uneven, the Dust Delete Data cannot be obtained properly
and a message telling you to try again will appear on the screen. The Dust Delete Data
obtained is subjoined to both the JPEG and RAW images regardless of the shooting
mode. The data is only a few kilobytes, so it will not affect the continuous shooting
speed or maximum burst. It is attached to all subsequent images until it is updated
again (via the procedure described here). It is recommended that the Dust Delete Data
be updated before a big shoot or after changing lenses in a dusty place.
If you use the Dust Delete Data feature and do not want to change the data of the dust
coordinates, you can disable the default self-cleaning operation so it does not operate
when the power is turned on or off. If you want to stop the Dust Delete Data from being
appended to the images, the Dust Delete Data must be erased with the [Clear all camera
settings] menu item.
DPP Ver. 2.1 had the copy stamp tool for manually selecting and erasing round dust
spots. This feature has been improved with the DPP Ver. 2.2 which can use the Dust
Delete Data to erase the dust spots automatically.
When an image contains Dust Delete Data, the automatic dust spot erasing process activates by starting the copy stamp tool and pressing the [Apply Dust Delete Data] button.
With DPP Ver. 2.2, the dust spots at the locations specified by the Dust Delete Data are
detected and erased if doing so is
deemed effective. This modest bit of artificial intelligence will be appreciated by
anyone who has done a little spotting or
retouching because certain things (and
it’s often difficult to figure out just which
ones) look worse after they’ve been
repaired and are better off left alone.
Digital Photo Professional Ver 2.2
New High-Precision
The Digital Rebel XTi has the same 9-point AF sensor and
9-Point AF System
AF unit as the EOS 30D, including the sophisticated dualprecision cross-type sensor in the center AF position.
This represents a very substantial upgrade from the
Digital Rebel XT. The XTi is the first entry-level EOS Digital
Additionally, the center AF point has a vertical-line sensitive sensor compatible with
f/5.6. Therefore, cross-type focusing is possible with any EF lens. The center AF point's
horizontal-line sensitive sensor for f/5.6 has a two-line, zigzag pattern. This redundancy
of focusing methods makes focus detection more consistent. As in the case of the EOS
30D, fine-tuning has been incorporated to improve the AF precision. Focusing performance under low light has been improved by 1 stop and is now possible from EV -0.5 to
AF point compatible with f/2.8, a feature unique in its
class. The XTi has some significant AF performance
improvements over the Digital Rebel XT. For example, the
XTi has the same wide-area focusing as the EOS 30D.
With an f/2.8 or brighter lens, the center AF point detects
focus with the f/2.8 light flux. The base line of the center
AF point's vertical-line sensitive sensor is twice as long
as that of an AF point compatible with f/5.6. This makes
focusing detection more precise.
camera to have an enhanced precision cross-type, center
EV 18. Finally, the wider focusing area with nine AF points and the diagonal configuration of AF points in and around the center afford improved subject focus tracking.
Focusing speed is on a par with that of the EOS 30D because the Digital Rebel XTi
shares its high-speed 32-bit RISC microcomputer. The algorithm for AI SERVO AF continuous shooting has been fine-tuned and optimized for 3 frames per second.
In the Creative Zone modes, the following AF modes can be selected with the AF mode
selection screen: One-Shot AF (when focus is achieved, AF operation stops and locks),
Predictive AI SERVO AF (tracks subject movement and focuses continuously until the start
of exposure) and AI Focus AF (automatic switching between One-Shot and Predictive AI
Servo AF). In the Basic Zone modes, the optimum AF mode is selected automatically, a
convenience for the less technically inclined, certainly a part of the XTi’s demographic. In
the Sports, Flash Off, and Basic Zone's Full Auto modes, the beeper sounds softly (when
the beeper is enabled) when focus is achieved with AI SERVO AF. In the Creative Zone
modes with AI SERVO AF, the beeper does not sound when focus is achieved. The AF
mode can be set even while the lens focus mode switch is set to MF. (When focus is
achieved, the focus confirmation icon and superimposed display lights up.) However,
"MF" will be displayed on the LCD screen when it displays the camera settings
The predictive AF calculation speed is the same as that of the Digital Rebel XT. With an
EF300mm f/2.8L IS USM lens, the camera can focus-track a moving subject approaching
at 31 mph/50 kph up to about 32.8 feet/10 meters away. As with the EOS 30D, the
lens drive keeps still when focusing a still subject with AI SERVO AF. If the subject
begins to move, the camera can start to focus-track the subject immediately because
focus detection is conducted continuously. As in the case of the EOS 30D, if you press
the shutter button completely in one quick stroke (rather than pressing halfway first),
the lens will focus, if possible, before the picture is taken. If focusing is not possible,
the picture will be taken anyway to give priority to taking the picture. This extreme
instance of shooting priority is especially useful should something occur that is so
remarkable that even less than perfect focus will not spoil the record of the moment.
Because the Digital Rebel XTi uses the same AF point
selection algorithm as the EOS 30D, there is a high probability that the correct AF point will be selected automatically. The selection procedure is the same as with the
Digital Rebel XT. With the Digital Rebel XTi, you can select
the AF point manually on the LCD screen's large and easyto-read display.
As with the Digital Rebel XT, the XTi’s AF-assist beam is a series of stroboscopic flashes.
It is not emitted in the Landscape, Sports or Flash OFF modes. In a Creative Zone mode,
it fires automatically when the built-in flash has been popped up manually. Firing can
be enabled/disabled with C.Fn-5. Emission time is 250 ms or less. The working range
is approximately 13.1 feet/4 meters at the center and approximately 11.5 feet/3.5
meters at the other 8 AF points. When an external EOS Speedlite is used, the AF-assist
beam of the external unit is used.
Manual Selection
* Focus can be achieved only with the center AF point.
Some of Canon’s competitors have chosen to use in-body image stabilization. The technique involves moving the image sensor in a controlled fashion, based on signals from
movement detecting sensors in the camera body. The obvious advantage of this system
is that users have some sort of stabilization available with almost any lens they connect
to the body. Short focal length lenses require smaller sensor deflections; 24 or 28 mm
lenses might need only 1 mm or so. Longer lenses necessitate much greater movement;
300 mm lenses would have to move the sensor about 5.5 mm (nearly 1/4”) to achieve
the correction Canon gets with its IS system at the same focal length. This degree of
sensor movement is beyond the range of current technology. Short and “normal” focal
length lenses need stabilization much less often than long lenses, so the lenses that
need the most help get the least. Further, in cameras with smaller than full-frame, 35
mm film size sensors, equivalent focal lengths become longer, by a factor of 1.5 or 1.6,
exacerbating the problem by making all lenses longer.
Less significant but still worth mentioning is the fact that in-body stabilization is not visible through the finder, whereas Canon lens-based stabilzation definitely is. Also, while
in-body stabilization works for many lenses, it does not presently work for all; high magnifications and macro lenses have caused it difficulties.
In the Canon IS system, the Image Stabilizer has an actual
lens group that can be moved up and down, or side-toside, in parallel to the imaging sensor or film plane. A pair
of sensors in the lens can detect horizontal or vertical
shake. Signals from these sensors are sent instantly to a
microprocessor in the lens and analyzed. The microprocessor then causes a group of lens elements, held in
place by a device called a coil, to move at the same amplitude and frequency of the shake to cancel it effectively.
1: No camera shake
Group 1 (focusing group)
Group 2 (image-stabilizing group)
To Object
Group 3 to 6
2: Lens front shakes downward
3: Image-stabilizing group counteracting
downward camera shake
Direction of Group 2
How the Image Stabilizer works
Canon is able to generate excellent image quality by stabilizing the image optically
before it ever reaches the imaging sensor in a digital SLR.
With the optical IS used by Canon, each lens with IS has a stabilizer unit designed for
that lens's needs. The unit in a lens such as the EF 28-135 f/3.5-5.6 IS USM or the EF-S
17-85 f/4-5.6 IS USM is vastly different from the powerful, broad movement stabilizers
in lenses such as the EF 400mm f/2.8L IS USM or the EF 600mm f/4L IS USM. All over
the world, photographers depend on Canon IS to help them achieve the highest possible image quality.
At some point, in-body stabilization may improve to the point at which such technology
may be appropriate for certain segments of Canon’s DSLR range. It would be senseless
to rule out such a possibility. Even now, differences in unit cost are not enough to be
significant factors in such a decision. The bottom line is performance.
New, Highly-Legible
2.5-inch TFT LCD
Color Screen
A 2.5-in., 230,000-pixel, color TFT LCD
screen with a wide, 160° viewing angle is
a welcome new feature of the Digital Rebel
XTi. Compared to the Digital Rebel XT's
1.8-in. LCD screen, the display area is
Horizontal viewing angle
Digital Rebel XTi
Digital Rebel XT
about twice as large. Also, to improve the
menu's readability, the font size has been
greatly increased. The LCD screen illumination is provided by three LED backlight modules and the brightness adjustment range has been expanded by one level at both the
minimum and maximum levels to a total of 7 steps. During brightness adjustment, a
handy and elegant grey scale is displayed along with the image.
Thanks to a highly transparent LCD screen and a brilliant LED module, screen brightness
is about 40% higher than the maximum brightness of the screens found on the EOS-1D
Mark II N, EOS 5D, and 30D. This makes it easier to review images even in bright outdoor
conditions. At the darkest setting, the display is not uncomfortably bright, even in a dark place. The maximum brightness setting changes the gamma characteristic of the
display to increase the midtones, making the
image look somewhat overexposed, and highlight detail tends to be lost. Therefore, it is
important that when checking an image's
exposure and colors, the brightness level be
set to one of the middle five levels. Because
the Digital Rebel XTi displays the camera settings at all times, users are recommended to set
the screen brightness to a suitable level which
would not be too bright in the dark.
2.5" LCD Screen
New Display-off sensor
When you put your eye on the eyepiece, a new display-off sensor (located below the
eyepiece) senses your face and turns off the LCD screen automatically. This is to save
battery power and prevent the screen's brightness from disturbing your eye while looking through the viewfinder. The display-off sensor consists of an IRED emitter and lightreceiving sensor. When the IRED light reflecting off the face is detected by the lightreceiving sensor, the LCD screen turns off automatically. This display-off sensor can be
disabled by setting the [LCD auto off] menu item to [Disable]. The camera setting display can also be turned off and on manually with the <DISP> button (formerly INFO) . If
the camera setting display is disabled, it might be difficult to discern whether the camera is turned on or not. A power lamp on the top of the camera is therefore provided to
indicate that it is on.
Other than a face, any object that comes near the disLight-receiving
play-off sensor will turn off the camera setting display
temporarily. The camera settings will be displayed again
when the face or object goes away from the camera.
Also note that if you are wearing sunglasses, they could
disperse the IRED light and the display-off sensor might
not be able to detect your face. Additionally, if a fluorescent light inverter is within 1
foot/30 cm of the display-off sensor, a pulse may cause the LCD screen to turn off
If auto power off is disabled and the camera is left on, the LCD screen will automatically
turn off after 30 minutes. (Power will not be turned off.) Normally, the camera settings
are displayed whenever the camera is turned on, but to save battery power, you can
have the LCD screen remain OFF even after you turn on the camera's power switch. To
do this, set C.Fn-11 [LCD display when power ON] to [Retain power OFF status]. This setting enables the camera to start up with the same LCD screen status (ON/OFF) as when
the power was turned off.
New User Interface
Basic operation concept
The new user interface of the Canon Digital Rebel XTi takes advantage of the state-ofthe-art, large, bright and sharp LCD screen to offer a faster, easier and more precise way
to operate the camera. The basic operation procedure of using the main dial, cross
keys, and various buttons to select and set functions is the same as with the Digital
Rebel XT. One difference is the XTi’s ability to switch the screen display easily among
the camera settings, menu screen and image playback. This is because camera settings
are now displayed, one might almost say magnified, on the LCD screen instead of on a
separate LCD panel. Other than when the menu screen or image playback is on view,
the camera settings are shown at all times unless the display is turned off. While the
menu screen or image playback is displayed, pressing the shutter button halfway will
bring back the camera settings. With previous cameras, pressing the shutter button
halfway turned off the LCD screen.
Camera setting
Image playback
New info display items
The large LCD screen has enabled 8 new items to be
added to the info display compared with the Digital Rebel
XT: ISO speed, Dimmer offset, AF frame display, White
balance adjustment, White balance bracketing, Beep,
Red-eye reduction mode, and Shooting display mode.
Camera side in effect
External flash side in effect
The least obvious of these, and perhaps the most clever, is Dimmer offset. One line
down from the top on the far right hand side of the display, either of two icons may
appear. The first is a standard lightning bolt with +/- after it. When this symbol, and a
number such as –2/3 appears, the display indicates that the built-in flash is set for an
exposure reduction of 2/3 stop. The other icon is a picture of a Speedlite, followed by
the same +/-. If that symbol is displayed, followed by, say, + 1 1/3, the display is indicating that the external flash attached to the Digital Rebel XTi is set for an increase in
exposure of 1 1/3 stops.
When exposure correction is applied, the exposure correction display in
the center of the second row on the LCD screen changes color for easy
reference. The screen also displays error and warning messages and
their solutions.
Full power
Low power
A change to the info display is that the battery power remaining indicator
now has 4 levels, rather than 3. The EOS 30D also offers this useful feature.
Battery almost dead
The viewfinder has two additions, both brought from the
EOS 30D: an FE lock indicator on the left side, and white
balance adjustment, +/-, on the right. The red-eye reduction mark is displayed on the LCD screen, so it is not
included in the viewfinder. Viewfinder blackout time is
approximately 170 ms at 1/60 second or faster shutter
speeds. A dioptric adjustment range from -3.0 to +1.0
dpt. is possible and an excellent Precision Matte focusing
screen is standard.
The Digital Rebel XTi has a depth-of-field preview feature, a welcome surprise at the new
camera’s price point. The button is located near the lens mount, under the left thumb
when the XTi is held horizontally. The feature is enabled in the Creative Zone modes.
SET button, cross keys, DISP.
The SET button is for selecting Picture Style directly. This is its default function. It promotes the use of Picture Styles, clearly differentiating the XTi from its rivals. Also, the
Picture Style logo is imprinted below the SET buttonas a reminder of this capability. The
cross keys are assigned with functions to set the ISO
speed, AF mode, white balance, and metering mode. The
procedures to set the ISO speed, AF mode, white balance, and metering mode are the same as with the Canon
EOS 30D. Settings take effect from the moment they are
selected. You no longer need to press the SET button to
register the setting.
Although the default setting for the SET button gives direct access to Picture Style,
C.Fn.01 can task the button with control of Quality (JPEG quality, RAW, or a combination
of the two), Flash exposure compensation (when using external flash, its flash exposure
compensation overrides the camera’s), Playback (switch instantly to Playback mode) or
Cross keys: AF frame selection (cross keys change AF point directly).
The name of the Info button has been changed to DISP. because it now turns the display
on and off. Its location is meant to make it easy to turn off the display to save energy.
Improvements to playback
In four playback-related improvements, the Digital Rebel XTi can now display a magnified or reduced view during quick review (C.Fn.10-1, magnified view on image review
and playback); automatic image rotation for images taken in vertical orientation may be
selected; a highly useful RGB histogram display is now provided, and CF card remaining
capacity has been added to the playback info screen.
As in the case of the Digital Rebel XT, the tabbed menu screens are operated with the
cross keys and SET button. Menu operation is possible even during the image writing
to the CF card after continuous shooting. Note that functions already assigned to cross
keys (ISO speed, etc.) are not included in the menus.
In all, there are 2 shooting menus, a playback menu and 2 set-up menus. The new
items are Picture Style and Dust Delete Data added to Shooting 2, Transfer order added
to Playback, LCD auto off added to Set-up 1, and Sensor cleaning: auto and Sensor
cleaning: manual added to Set-up 2. Changed items are the Histogram in Playback (RGB
added), Auto power off, Auto rotate, LCD brightness and File numbering in Set-up 1, and
2 Custom Functions added to Set-up 2. Any of the following 15 languages can be selected for the LCD screen language: English, German, French, Dutch, Danish, Finnish,
Italian, Norwegian, Swedish, Spanish, Simplified Chinese, Japanese, Traditional
Chinese, Korean and Russian.
Picture Style
Picture Style, which Canon is implementing across its full
EOS Digital range, is new to the sub-$1000 category. It can
be selected directly with the SET button, or through
Shooting menu 2. For the first 5 choices, Standard, Portrait,
Landscape, Neutral and Faithful, the variables are sharpness, contrast, saturation and color
tone. Each Style has preset values for these image characteristics that can be changed by
the user in the menu. The process of selecting or refining a Picture Style can be likened to
deciding on a film: something a little more saturated and sharper, or perhaps something
less forward with a subtle palette and a less-scientific representation of skin textures. The
sixth Picture Style is Monochrome, whose variables are Sharpness, Contrast, Filter effect
and Toning effect. Last, there are 3 open slots for User Defined styles.
Custom Functions
The Digital Rebel XTi has 11 Custom Functions with 29 settings to choose from. Four functions were added or changed on the XTi relative to the XT: C.Fn 1: SET button functions (0:
Picture Style, 1: Quality, 2: Flash exposure compensation adjustment, 3: Flash exp comp,
4: Cross keys: AF frame selec.), C.Fn 2: Long exposure noise reduction (Off/Auto/On),
C.Fn 10: Magnified view (0: Image playback only, 1: Image review and playback), and
C.Fn.11: LCD display when power ON (0: Display, 1: Retain power OFF status).
Note that with C.Fn-7-1 (mirror lockup) set, one should not point the camera toward the
sun or any bright light source. Doing so can damage the shutter curtains, cause stray
light to enter, or damage the imaging sensor.
Camera Direct Printing
Several useful improvements have been added to the Direct Print feature on the Digital
Rebel XTi:
• Contact sheet style 35 image index printing
• Printing with shooting information
• 20 image index printing with shooting information
20-image print with
EXIF information
35-image contact sheet
Single image print with EXIF information
• Red-eye reduction function
• Face brightening correction function
• Addition of supported paper sizes
(4" x 8", 10" x 12", 8" x 10", 14" x 17")
• Improved printing effects (Natural,
Natural M, B/W, Cool Tone, Warm Tone
• Adjustment of printing parameters
• Addition of supported paper (Fine Art
Photo Rag, Super Photo paper)
Many of these items appeared on the
EOS 30D. Beginners and advanced
photographers alike will find them
useful and appealing.
without Red-eye reduction
with Red-eye reduction
without face brightner
with face brightner
PIXMA 6700D and
Digital Rebel XTi
In the Digital Rebel XTi, when one uses
a printer compatible with this feature,
the USB cable can now be disconnected when the image transfer to
the printer is completed, even if printing continues. Previously, early
cable removal caused the printer to cancel the job. The Print/Share button’s blue lamp
blinks during image transfer. When the transfer is completed, the blinking stops and the
USB cable can be disconnected. This change is a convenience when one is printing multiple images or if the print size is large.
For Print Order (DPOF) and Direct Image Transfer, the specifications are the same as with
the EOS 30D. With the Digital Rebel XT, it was necessary to use the Communication
menu when switching between direct printing and connection to a personal computer.
With the Digital Rebel XTi, the PTP protocol is now the same for both, making it unnecessary to switch. The menu therefore no longer has the Communication setting.
Direct Image Transfer
As with the EOS 30D, images shot with the Digital Rebel XTi can be transferred directly
to a Mac or Windows computer just by connecting the camera to a PC using interface
cable IFC-400PCU (included), selecting [EOS Utility] in the dialog that appears, and
beginning the transfer by pressing the SET button or the Print/Share button. The choices are:
1. All images-- All images stored in a CF card are transferred to the PC.
2. All images not yet transferred-- Only images that haven't been transferred to the PC
are automatically selected for transfer.
3. Images marked for transfer-- Images designated in the menu's [Transfer order] item are
transferred to the PC. In [Transfer order], you can choose either [Order] for individual
images or [All] for all images. Procedures for marking images for transfer are the same
as for marking individual images for DPOF. Up to 998*** images can be marked.
4. Select image and transfer-- Select images and transfer them to the PC.
5. Wallpaper for computer-- Select an image to use as the background (wallpaper) for
the computer screen and transfer it to the PC. A JPEG file is automatically converted
into a BMP file to be transferred and appears as the background (wallpaper) for the
computer screen. RAW images cannot be transferred for this purpose.
Design and Construction
The Digital Rebel XTi is a compact, stylish and attractive DSLR that continues the design
concept of its predecessor, the Digital Rebel XT. The exterior surface is now coated with a
leathery paint finish to make fingernail scratches less noticeable. The Canon logo is a bit
bigger to make it stand out better in retail situations (2 mm wider and 0.4 mm higher).
To improve holding ease, a convenient new rubber slip guard for the thumb (back, top
right) and a new grip shape in the back have been incorporated. The grip is also thicker
by 1 mm. The texture of the mode dial has been changed. The Print/Share button is now
on the upper left on the back of the camera where the digital control buttons are concentrated. Clearly separating the digital control buttons and camera control buttons makes
the camera easier to operate. The new screen and the elimination of the bifurcated display give the back of the camera a cleaner and more integrated appearance.
The camera body construction of the
Digital Rebel XTi is very similar to that of
the Digital Rebel XT, a camera of proven
ruggedness and reliability. The stainless
steel chassis and mirror box made of
high-strength engineering plastic (polycarbonate with glass fiber) make the body as
strong as the XT’s. As with the XT, the
camera's top, front, and rear covers are
made of special engineering plastic (ABS resin, polycarbonate resin, and polycarbonate
resin with special conductive fibers) for light weight, high strength, and electromagnetic
shielding. The XTi will come in two color versions, silver and black.
The basic internal components and configuration are the
same as those of the Digital Rebel XT. The following units
have been added or modified: Self Cleaning Sensor Unit
(added), Display-off sensor unit (added), LCD screen (size
increased from 1.8 in. to 2.5 in.), LCD panel (eliminated).
Note that in every parts category (except lead wires, which
remain unchanged at 12), the parts count on the Digital
Rebel XTi has increased relative to its predecessor. The
total is now 1508, compared to 1319 previously. This is a
good, if somewhat generalized, indication that the Digital
Rebel XTi is a more sophisticated, and more expensive to
produce, camera than the Digital Rebel XT, and that it
offers exceptional value in the sub-$1000 category.
Lead wires
Screws and
• The shutter unit is counted as 1 part.
• The E-ring is counted as a washer.
• The official total excludes the screws and washers.
The XTi’s weight is still very modest although it has increased by 25 grams to 510g/18
oz., excluding battery pack, CF card and body cap, but including the backup battery and
the eyecup.
While based on the Digital Rebel XT’s electrical components, the XTi’s electrical components are compatible with several significant new features, such as the 10.10megapixel CMOS sensor, Self Cleaning Sensor Unit, Display-off sensor, and the 2.5in. LCD screen. As with the XT, the XTi's main circuit board is a highly-integrated 8layer board fitted with the digital control circuit, camera control circuit, image-signal
processing circuit, and DC/DC converter circuit. In addition, there are five hard
boards, and sixteen flexible boards.
Flash Circuit Board
Self Sensor Cleaning Unit
Circuit Board
External Interface
Circuit Board
Motor Drive Board
DIGIC II Image Processor
Main board (top)
Main board (bottom)
The USB 2.0 Hi-Speed, mini B port enables high-speed image transfers from the camera
to a personal computer (see Direct Image Transfer) using Interface Cable IFC-400PCU
(included). Also, the PTP protocol is now used for both Camera Direct printing and
transmissions to a personal computer, making it unnecessary to switch the communications setting.
An NTSC/PAL video output terminal is provided; it uses Video Cable VC-100 (included).
The remote control terminal is compatible with Remote Switch RS-60E3 (2.5 mm dia.
mini jack, optional***). Wireless remote control is compatible with Remote Controllers
RC-1 and RC-5 (optional). The wireless remote control receiver is built inside the camera
grip. The system is compatible with all shooting modes and works within approx. 5
m/16.4 ft. (at front and center). When the Drive mode button is pressed, the selftimer/wireless remote control timer icon is displayed on the LCD screen.
Drive and Power Source
The maximum continuous shooting speed of the Digital Rebel XTi is approx. 3 fps (in
both the One-Shot AF and AI SERVO AF modes), the same as the Digital Rebel XT in spite
of the larger files the XTi generates. This is achieved by a number of features: the reflex
mirror drive and shutter drive are controlled independently; the advanced, Canondesigned and -manufactured CMOS sensor enables high-speed signal reading, and the
DIGIC II image processor performs high-speed image processing.
To limit the increase in power consumption required by high-speed reading, the output
amp's power consumption has been minimized. Further, during long exposures, power
to the output amp is cut off and the standard current for the circuit drive is also suspended, as in the case of the Digital Rebel XT.
The maximum burst in Large/Fine mode is approx. 27 shots for JPEG and 10 shots for
RAW, twice as many as with the Digital Rebel XT. Also, with white balance bracketing
enabled, up to 6 shots can be taken continuously, whereas only 2 shots were possible
with the XT.
Recording Quality
Max. Burst [Approx.]
• The figures above are based on Canon's testing standards with a 512MB CF card. (The figures can also vary depending on the CF card.)
• As with the K189, image processing occurs even during continuous shooting. This increases the maximum burst.
• During white balance bracketing, the maximum burst during continuous shooting will be lower.
The Battery Life table indicates the
approximate number of shots that can be
obtained under varying temperatures and
shooting conditions. Using any of the following techniques can conserve power
and increase the number of possible
Shooting Conditions
AE 100%
AE 50% FA 50%
At 23°C / 73°F
At 0°C / 32°F
• Based on one fully-charged NB-2LH battery and CIPA testing standards.
1. With the Digital Rebel XT, the shortest power-off time was 1 minute. The default setting for auto power off is now 30 seconds.
2. Because the LCD screen can now be turned off/on with the DISP. button, battery
power can be saved even if auto power-off has been disabled or set to a long time
period. You can choose to display the camera settings only when needed. To make
it easier to press the DISP. button, it is positioned at the top of the column of digitaloperation buttons on the camera back.
3. With the C.Fn-11-1 set to [Retain power OFF status] , the camera settings will not be
displayed. In the Full Auto mode, because one need not worry about the shutter
speed and aperture settings, using both C.Fn-11-1 and DISP. to display the camera
settings only when necessary will further save battery power.
As high-capacity media (2 GB and up) have become more common because of the
decline in their cost, Canon has chosen to take advantage by changing folder-related
specifications to make them identical to those of Canon’s high end models. The
changes improve the facility with which one can search for images when large numbers
of them are involved. In previous models, one folder could hold up to 100 images; now,
9,999 images can be stored in a single folder. A Force-Reset option has also been
added which causes the image number to reset as 0001, and a new folder to be created. Scenes shot separately can now be kept in separate folders, an obvious convenience.
Accessories and System
The Digital Rebel XTi shares its major accessories with the its predecessor, the Digital
Rebel XT. The BG-E3 battery grip makes it easy to shoot vertically and has magazines for
either two NB-2LH batteries or three AA batteries. The EH18-L semi-hard case and EW100DBII wide strap continue. Power accessories include the CB-2LW battery charger (for
Japan and the Americas), the CB-2LWE charger (for Europe, Asia, South Korea and
China), the ACK-DC20/ACK700 AC adapter kits and the CBC-NB2 car battery charger.
With a few minor exceptions, the Digital Rebel XTi is fully compatible with the vast
Canon EOS system of EF and EF-S lenses, Speedlites, switches, remotes, cables and
Interchangeable Lenses
Lens Mount Converter FD-EOS
Macro Lens Mount Converter FD-EOS
Although it can be used with manual exposure,
exposure error occurs. Therefore, these items will
be officially listed as incompatible.
Not compatible
Compatible with manual flash (does not fire
in A-TTL/TTL autoflash modes).
Not compatible (since it only has
autoflash modes, it cannot fire).
Wired multi-Speedlite accessories
(since it cannot fire in Manual flash mode when
used with TTL hot shoe adapter).
System accessories not listed above are completely compatible with Digital Rebel XTi.
With the Digital Rebel XTi, Canon continues its tradition of including a complete package
of useful and appropriate software at no additional cost with each of its DSLR cameras.
The EOS Digital Solution Disk (Ver. 13.0) includes the upgraded Zoom Browser EX (Ver.
5.7, Windows)/Image Browser (Ver. 5.7, Mac), Digital Photo Professional (Ver. 2.2), EOS
Utility (Ver. 1.1), Photostitch (Ver. 3.1), and the PTP TWAIN/WIA driver (Windows). The
second CD contains information explaining the use of all the application software on the
EOS SolutionDisk. The Digital Photo Professional RAW conversion and workflow application now supports Dust Delete Data, and its RGB tone curve adjustment function has
been expanded to include an extended range of effectiveness and human face detection.
Supported Operating System
EOS Utility
Digital Photo Professional
OS X 10.2
OS X 10.3
OS X 10.4
CameraWindow MC
RAW Image Task
Macintosh: Intel Mac (Universal Binary) supported
Windows: Vista cupport Schedule udner consideration
Image Sensor
Recording System
Type: Digital AF/AE SLR with built-in flash
Recording Medium: CompactFlash (CF) Card Type I & II
Image Sensor Size: 0.87 x 0.58 in./22.2 x 14.8mm (APS-C size sensor)
Compatible Lenses: Canon EF and EF-S lenses
Lens Mount: Canon EF mount
Lens Focal Length Conversion Factor: 1.6x
Type: High-sensitivity, high-resolution, single-plate, CMOS sensor
Effective Pixels: Approx. 10.10 megapixels
Total Pixels: Approx. 10.50 megapixels
Aspect Ratio: 3:2 (Horizontal : Vertical)
Color Filter System: RGB primary color filters
Low-pass Filter: Fixed position in front of the CMOS sensor
Dust Delete Feature: (1) Auto Sensor Cleaning, (2) Dust Delete Data, (3) Manual Sensor
File Format: Design rule for Camera File System 2.0 and Exif 2.21
Recording Format: JPEG, RAW, and RAW+JPEG simultaneous recording provided. The
RAW and JPEG images are saved as separate files in the CF card.
Image Compression: JPEG, RAW (Canon .CR2)
File Size: (1) Large/Fine: Approx. 3.8MB (3,888 x 2,592), (2) Large/Normal: Approx.
2.0MB (3,888 x 2,592), (3) Medium/Fine: Approx. 2.3MB (2,816 x 1,880),
(4) Medium/Normal: Approx. 1.2MB (2,816 x 1,880), (5) Small/Fine: Approx. 1.3MB
(1,936 x 1,288), (6) Small/Normal: Approx. 0.7MB (1,936 x 1,288), (7) RAW: Approx.
9.8MB (3,888 x 2,592)
Folders: Automatic folder creation; up to 9,999 images per folder (new folder created
when the file number reaches 9999)
File Numbering: (1) Continuous numbering (2) Auto reset (3) Manual reset (the image
numbering is reset to 0001, a new folder is created where subsequent images are
Color Space: Selectable between sRGB and Adobe RGB
Picture Style: Six preset Picture Style settings plus three user-defined custom Picture
Style settings with individual adjustments for Sharpness, Contrast, Color saturation,
2nd Color tone; Filter effect, Toning effect for black & white images
Interface: USB 2.0 Hi-Speed, mini-B port. NTSC/PAL for video output
Whtie Balance
Settings: Auto, Preset (Daylight, Shade, Cloudy, Tungsten Light, White Fluorescent Light,
Flash), Manual (Custom, or user-set Color Temperature)
Auto White Balance: Auto white balance with the image sensor
Color Temperature Compensation: White balance bracketing: +/- 3 stops in 1-stop
White balance correction: blue/amber bias +/- 9 levels, magenta/green bias +/- 9 levels.
When blue/amber bias and magenta/green bias set with White balance correction,
white balance bracketing cannot be set to more than +/- 9 levels
Type: Eye-level SLR with pentamirror
Coverage: Approx. 95% horizontally and vertically
Magnification: 0.8x (-1 dpt with 50mm lens at infinity)
Eyepoint: Approx. 21mm
Dioptric Adjustment Correction: -3.0 to +1.0 diopter
Mirror: Quick-return half mirror (Transmission: reflection ratio of 40:60)
Viewfinder Information: AF (AF points, focus confirmation light), Exposure (shutter
speed, aperture, exposure level, AE lock, exposure compensation, AEB level, bulb),
Flash (flash ready, red-eye reduction lamp on, high-speed sync, FE lock, FEB shooting,
flash exposure compensation, insufficient flash warning during FE lock), White balance
correction, Maximum burst, CF card full warning, CF card error warning, No CF card warning
Depth-of-Field Preview: Enabled with depth-of-field preview button (with Speedlite
580EX, 430EX, MR-14EX or MT-24EX; pressing the depth-of-field preview button fires a
modeling flash)
Eyepiece Shutter: None (eyepiece cover provided on strap)
Type: TTL-CT-SIR with CMOS sensor
AF points: 9 AF points
AF Working Range: EV -0.5–18 (ISO 100 at 73°F/23°C)
Focusing Modes: Autofocus: One-Shot AF, Predictive AI Servo AF, AI Focus AF (automatic
switching between One-Shot/Predictive AI Servo AF); Manual Focus (MF)
AF Point Selection: Automatic selection, Manual AF point selection
Selected AF Point Display: Superimposed on viewfinder and LCD monitor
AF-assist Beam: Intermittent firing of built-in flash (Emitted automatically when necessary
under low light, and linked to all 9 AF points. Not emitted in the Landscape, Sports and
Flash OFF modes)
Exposure Control
Metering Modes: Max. aperture TTL metering with 35-zone SPC, (1) Evaluative metering
(linked to all AF points), (2) Partial metering (approx. 9% at center of viewfinder),
(3) Center-weighted average metering
Metering Range: EV 1–20 (ISO 100 at 73°F/23°C with EF 50mm f/1.4 USM lens)
Exposure Control Systems: Program AE (shiftable), Shutter-priority AE, Aperture-priority
AE, Auto Depth-of-field AE (non-shiftable), Full auto (Program AE, non-shiftable),
Programmed image control modes, Manual exposure (including bulb), E-TTL II autoflash
program AE
ISO Speed Range: Basic Zone: automatically set by the camera; Creative Zone:
equivalent to ISO 100–1,600
Exposure Compensation: (1) User-set with multi-controller (2) AEB (Auto Exposure
Bracketing range: +/- 2 stops in 1/3- or 1/2-stop increments
AE Lock: Auto: Applied in One-Shot AF mode with evaluative metering when focus is
User-set: Applied with AE lock button
Type: Vertical-travel, mechanical, focal-plane shutter with all speeds electronically
Shutter Speeds: 1/4000 to 30 sec. (1/3- and 1/2-stop increments), X-sync at 1/200
Shutter Release: Soft-touch electromagnetic release; shutter “lag time” approx. 100
Self-Timer: 10 sec. delay, 2 sec. delay with C.Fn-7-1 (mirror lockup)
Remote Control: Remote control with Remote Switch RS-60E3 or Wireless Remote
Controllers RC-1/RC-5.
Built-in Flash
Type: Auto pop-up, retractable, built-in flash in the pentaprism
Guide Number: 43 ft./13m (ISO 100)
Recycling Time: Approx. 3 sec.
Flash-ready Indicator: Flash-ready indicator lights in viewfinder
Flash Coverage: 17mm lens focal length (equivalent to 27mm in 135 format)
Flash Metering System: E-TTL II autoflash
Flash Exposure Compensation: +/-2 stops in 1/3- and 1/2-stop increments
EOS External Flash or Dedicated Speedlite: E-TTL II autoflash with EX Series Speedlites
Drive System
Drive Modes: Single, Continuous, Self-timer/Remote control
Continuous Shooting Speed: Approx. 3 fps (at a shutter speed of 1/250 sec. or faster)
Max. Burst During Continuous Shooting: JPEG: approx. 27 frames (Large/Fine); RAW:
approx. 10 frames; RAW+JPEG: approx. 8 frames (Large/Fine)
LCD Monitor
Image Protection
And Erase
Type: TFT color, liquid-crystal monitor
Monitor Size: 2.5 in. diagonal with a viewing angle of approx. 160° vertically and
Pixels: Approx. 230,000 pixels
Coverage: Approx. 100%
Brightness Control: 7 levels provided
Image Display Format: Single image, 9-image index, Magnified zoom (approx. 1.5x to
10x), Auto play, Auto review right after shooting, Histogram, Rotate, Jump
Highlight Alert: In the single image (INFO) display mode, the highlight portions
containing no image information will blink
Protection: A single image can be protected or unprotected
Erase: A single image or all images stored in a CF card can be erased if they are
Direct Printing from the Camera: Enabled with the Print/Share button
Compatible Printers: CP and SELPHY Compact Photo Printers, PIXMA Photo Printers
and PictBridge compatible printers (via USB Interface Cable IFC-400PCU)
Settings: Print quantity, style (image, paper size, borders, date), trimming
Menu Categories: Shooting menu: red, Playback menu: blue, Setup menu: yellow
LCD Monitor Languages: 15 languages provided (English, German, French, Dutch,
Danish, Finnish, Italian, Norwegian, Swedish, Spanish, Russian, Simplified Chinese,
Traditional Chinese, Korean, Japanese)
Firmware Update: Enabled by the user
Power Source
Battery: One Battery Pack NB-2LH
Number of Shots
Dimensions And Weight
No Flash Used
50% with Flash
Normal temp (73°F/23°C)
Low temp (32°F/0°C)
500 frames
370 frames
360 frames
280 frames
Normal temp (73°F/23°C)
Low temp (32°F/0°C)
1000 frames
740 frames
720 frames
560 frames
Dimensions (W x H x D): 4.98 x 3.71 x 2.56 in./126.5 x 94.2 x 65mm
Weight: 18 oz./510g (body only)
Operating Environment
Operating Temperature Range: 32–104ºF/0–40ºC
Operating Humidity Range: 85% or less
Canon and DIGIC are registered trademarks, and SELPHY and PIXMA are trademarks,
of Canon Inc. in the United States and may also be registered trademarks or trademarks
in other countries. IMAGEANYWARE is a trademark of Canon. Microsoft and Windows
are trademarks or registered trademarks of the Microsoft Corporation in the United
States and/or other countries. Mac is a trademark of Apple Computer, Inc., registered
in the United States and other countries. Adobe Photoshop is a registered trademark
of Adobe Systems incorporated and its subsidiaries in each country. All other products
and brand names are registered trademarks, trademarks or service marks of their
respective owners.
• All the specifications above are based on Canon's Standard Test Method.
• The camera's specifications and physical appearance are subject to change without notice.
• TFT monitor images shown in this white paper are simulated.
Microsoft® and Windows® are registered trademarks or trademarks of Microsoft Corporation in the United States and / or
other countries, Macintosh® is a registered trademark or trademark of Apple Computer Inc. in the United States and / or other
countries. CompactFlash™ is a trademark of SanDisk Corporation. Microdrive™ is a trademark of IBM Corporation. Adobe
Photoshop is a registered trademark of Adobe Systems Incorporated and its subsidiaries in each country. The other product
and brand names appearing in this brochure are trademarks or registered trademarks of their respective owners. TFT monitor
images shown in this brochure are simulated.
The Canon Digital Rebel XTi is a formidable camera on many levels. Its image quality is
unequaled in its category and is good enough to be compared favorably with cameras
costing up to twice as much. Its ease of use enables owners with any level of expertise
to get superb results. Its comprehensive dust solution mitigates one of the true
annoyances of DSLR ownership. Its compact body and refined ergonomics make it a
pleasure to live with.
The Digital Rebel XTi will certainly be a great success in the marketplace. As photographers
become acquainted with the XTi, it is likely that advanced amateurs and professionals
will find it as irresistible as beginners will. For journalists, wedding photographers
and portraitists, it has the resolution, the image quality and the proven reliability to
serve nobly. When its complete compatibility with the legendary Canon EOS system is
taken into account, the Digital Rebel XTi will certainly be recognized by photographers
everywhere as the finest value and most appealing sales proposition of any DSLR in its
price class and well beyond.
Contents ©2006 by Canon U.S.A., Inc. All Rights Reserved. Excerpts from this material may be quoted in
published product reviews and articles. For further information, please contact Canon U.S.A., Inc. Public
Relations Dept., (516) 328-5000.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF