Samsung | SCC-C6407 | Instruction manual | Samsung SCC-C6407 Instruction manual

Samsung SCC-C6407 Instruction manual
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
1
SmartDome Camera
SCC-C6407(P)
Owner’s Instructions
Benutzerhandbuch
Manuel d’instruction
Manual del usuario
Istruzioni per l’uso
Part : AB68-00547A(00)
Printed in China
E
D
F
Es
I
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings, Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, or
other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding- type plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus.
13. Unplug this apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Safety Precautions
The purpose of this information is to ensure proper use of this product to
prevent danger or damage to property. Please be sure to observe all
precautions.
* The precautions are divided into "Warnings" and "Cautions" as
distinguished below:
Warning: Ignoring this warning may result in death or serious injury.
Caution: Ignoring this caution may result in injury or damage to property.
Warning instructions alert you to
a potential risk of death
or serious injury.
Caution instructions alert you to the
potential risk of injury or
damage to property.
Warning
1. Be sure to use only the standard adapter which is specified in the
specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to
the product.
2. When connecting the power supply and signal wires, check the external
connection terminals before connecting them. Connect the alarm signal
wires to the alarm terminals, the AC adapter to the AC power input
receptacle, and the DC adapter to the DC power input, making sure that
the correct polarity is observed.
(Connecting the power supply incorrectly may cause fire, electrical shock,
or damage to the product.)
3. Do not connect multiple cameras to a single adapter.
(Exceeding the capacity may cause abnormal heat generation or fire.)
(A falling camera may cause personal injury.)
4. Securely plug the power cord into the power receptacle.
(Insecure connection may cause fire.)
5. When installing the camera on a wall or ceiling, fasten it securely and
firmly. (A falling camera may cause personal injury.)
E
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
5
6. Do not place conductive objects (e.g., screwdrivers, coins, and metal
things) or containers filled with water on top of the camera. (Doing so may
cause personal injury due to fire, electrical shock, or falling objects.)
7. Do not install the unit in humid, dusty, or sooty locations.
(Doing so may cause fire or electrical shock.)
8. If any unusual smells or smoke come from the unit, stop using the product.
In such case, immediately disconnect the power source and contact the
service center. (Continued use in such a condition may cause fire or
electrical shock.)
9. If this product fails to operate normally, contact the store of purchase or
your nearest service center. Never disassemble or modify this product in
any way. (SAMSUNG is not liable for problems caused by unauthorized
modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product.
(Doing so may cause fire or electrical shock.)
Wipe the surface with a dry cloth. Never use detergents or chemical
cleaners on the product, as this may result in discoloration of surface or
cause damage to the finish.
Caution
1. Do not drop objects on the product or apply strong shock to it. Keep away
from a location subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 122°F), low
temperature (below 14°F), or high humidity.
(Doing so may cause fire or electrical shock.)
3. Avoid a location which is exposed to direct sunlight, or near heat sources
such as heaters or radiators.
(Neglecting to do so may result in a risk of fire.)
4. If you want to relocate the already installed product, be sure to turn off the
power and then move or reinstall it.
5. Install in a well-ventilated location.
6. Remove the power plug from the outlet when there is a lightning storm.
(Neglecting to do so may cause fire or damage to the product.)
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
E
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
1-1
Before Usage
This is a basic instruction manual for the SCC-C6407(P) user.
It contains all the instructions needed to use the SCC-C6407(P)
from a simple introduction of the control locations and functions of
the SCC-C6407(P) to installation methods in the set up menu.
We recommend all users of the SCC-C6407(P) from the
advanced user who has used similar cameras before to the
general user to read the instruction manual before using.
E
The most frequently used feature in the SCC-C6407(P) would be
the SCC-C6407(P) Setup Menu.
The SCC-C6407(P) Setup Menu is explained in detailed in
"Chapter 3 Setup Menu Overview".
The instructional manual is best used when read from beginning
to end, but for users wanting to read only the part they need here
are the Chapter summaries.
"Chapter 1 SCC-C6407(P) Overview" includes a brief
introduction of the SCC-C6407(P), part names and functions, and
Switch Settings.
"Chapter 2 SCC-C6407(P) Installation" explains the installation
procedures of the SCC-C6407(P) and provides preparation and
installation environment requirements.
"Chapter 3 Setup Menu Overview" presents the structure of the
Setup menu for the SCC-C6407(P) including a detailed
explanation of the functions performed in each submenu.
"Appendix SCC-C6407(P) Product Specifications" contains
product specifications of the SCC-C6407(P) in itemized
categories.
1-1
1-2
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
1-3
Table of contents
Before Usage...............................................................................................1-1
Chapter 1 SCC-C6407(P) Overview ............................................................1-5
SCC-C6407(P) Introduction ...........................................................1-6
Locations of Control .......................................................................1-7
FRONT...........................................................................................1-7
BACK .............................................................................................1-8
ADAPTER CONNECTION.............................................................1-9
INITIAL SETTING ..........................................................................1-10
Setting RS-422A/RS-485 termination ............................................1-11
Chapter 2 SCC-C6407(P) Installation .........................................................2-1
Before Installing .............................................................................2-2
Preparing the Cables .....................................................................2-3
Cable Connection ..........................................................................2-4
Installing SCC-C6407(P)................................................................2-5
Installing the Camera .....................................................................2-8
Chapter 3 Setup Menu Overview ................................................................3-1
Structure of the Setup Menu ..........................................................3-2
1. CAMERA SET ...........................................................................3-4
- CAMERA ID.............................................................................3-4
- V-SYNC ...................................................................................3-5
- COLOR/BW .............................................................................3-6
- MOTION DET ..........................................................................3-7
- ZOOM SPEED.........................................................................3-8
- DIGITAL ZOOM .......................................................................3-9
- DISPLAY ZOOM......................................................................3-9
- DISPLAY P/T ...........................................................................3-9
- EXIT.........................................................................................3-10
2. VIDEO SET ...............................................................................3-10
- IRIS..........................................................................................3-10
- ALC.......................................................................................3-10
- BLC.....................................................................................3-10
- WDR .....................................................................................3-11
- MANU ...................................................................................3-11
- SHUTTER................................................................................3-12
- FLICKERLESS ......................................................................3-12
- AGC .........................................................................................3-13
- MOTION ..................................................................................3-13
- WHITE BAL .............................................................................3-14
- DIS...........................................................................................3-15
- FOCUS MODE ........................................................................3-16
- SPECIAL..................................................................................3-16
- EXIT.........................................................................................3-16
3. PRESET.....................................................................................3-17
- POSITION SET........................................................................3-18
- PRESET ID..............................................................................3-18
- VIDEO SET..............................................................................3-18
- PRESET SPEED .....................................................................3-18
- DWELL TIME...........................................................................3-18
- IMAGE HOLD ..........................................................................3-18
- EXIT.........................................................................................3-18
1-3
4. ZONE SET ..................................................................................3-19
- PRIVACY ZONE .......................................................................3-19
- STYLE....................................................................................3-19
- BLANK ALL ABOVE...............................................................3-20
- BLANK ALL BELOW ..............................................................3-20
- PRYVACY ZONE MAP ..........................................................3-20
- SET ZONE AREA ...............................................................3-21
- SET ZOOM .........................................................................3-22
- REVERSE ...........................................................................3-22
- EXIT ....................................................................................3-22
- ZONE DIR SET/ZONE AREA SET ...........................................3-22
- ZONE DIR SET .........................................................................3-23
- ZONE AREA .............................................................................3-23
- LOCATION.............................................................................3-24
- ZONE ID SET.........................................................................3-24
- ZONE ENABLE ......................................................................3-24
5. AUTO SET ..................................................................................3-25
- AUTO PAN................................................................................3-25
- POSITION SET ......................................................................3-25
- DIRECTION ...........................................................................3-26
- ENDLESS ..............................................................................3-26
- SPEED ...................................................................................3-26
- DWELL TIME .........................................................................3-26
- PATTERN .................................................................................3-26
- SCAN ........................................................................................3-27
- AUTO PLAY ..............................................................................3-28
- AUTO RETURN .....................................................................3-28
- AUTO PLAY ...........................................................................3-28
- PLAY NUMBER .....................................................................3-28
6. ALARM SET ................................................................................3-29
- ALARM PRIORITY SET............................................................3-29
- ALARM IN SET .........................................................................3-29
- ALARM OUT SET .....................................................................3-29
- AUTO SET ................................................................................3-30
- AUX OUT CONTROL................................................................3-30
7. OTHER SET ................................................................................3-30
- PROPORTINAL P/T..................................................................3-30
- TURBO P/T ...............................................................................3-31
- AUTO CAL ................................................................................3-31
- D-FLIP.......................................................................................3-31
- CAM RESET .............................................................................3-31
- LANGUAGE ..............................................................................3-31
- PASSWORD .............................................................................3-31
8. SYSTEM INFO ............................................................................3-32
9. SHORT KEYS .............................................................................3-33
E
Product specifications ............................................................................3-35
1-4
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
1-5
Chapter 1 SCC-C6407(P) Overview
In this chapter we will briefly introduce the SCC-C6407(P) and
show main functions, locations of control and Switch Setting.
SCC-C6407(P) Introduction
SCC-C6407(P) is a zoom lens built in smart dome camera which
provides you with the best monitoring function in connection with
CCTV at banks or companies.
E
The SCC-C6407(P) is a high quality surveillance camera using x32
zoom lens and digital zoom IC, it can catch clear images up to 320
times.
SCC-C6407(P) has a variety of functions such as;
- WDR to cover the full screen irregardless of its brightness,
- DAY/NIGHT to improve the sensitivity by automatic conversion
into the black and white mode at night or in the environment with
low illumination,
- White Balance to control the brightness to the illumination,
- Backlight Compensation under spotlight or utmost bright
illumination,
- Auto Focus to automatically adjust the focus to the subject
movement,
- Privacy zone to hide a specific area for personal privacy, and,
- PAN/TILT for precise control at high speed.
The SCC-C6407(P) uses an Alarm function for alert situations and
moving camera in the direction you want, ZOOM-IN and
ZOOM-OUT functions can be remote controlled.
1-5
1-6
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
1-7
Locations of Control
FRONT
BACK
E
1-7
1-8
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
1-9
ADAPTER CONNECTION
INITIAL SETTING
SCC-C6407(P) Adapter BOARD
CAMERA ADDRESS SETUP
Use SW701, SW702, or 703 for Camera Address setup. You may allocate
up to 255 addresses by using SW701 to set the 3rd digit, SW702 the 2nd
digit, and SW703 the 1st digit.
EX) In case of Camera Address 1, see the following figure for setup.
E
SW701
SW703
SW702
Setting communication Protocol
Use number 1~4 PIN of SW704 to set communication Protocol.
PIN
Comp
PIN1
PIN2
PIN3
PIN4
A
OFF
OFF
OFF
OFF
B
ON
OFF
OFF
OFF
C
OFF
ON
OFF
OFF
D
ON
ON
OFF
OFF
E
OFF
OFF
ON
OFF
F
ON
OFF
ON
OFF
G
OFF
ON
ON
OFF
H
ON
ON
ON
OFF
I
OFF
OFF
OFF
ON
J
ON
OFF
OFF
ON
K
OFF
ON
OFF
ON
ON
L
ON
ON
OFF
M
OFF
OFF
ON
ON
N
ON
OFF
ON
ON
O
OFF
ON
ON
ON
P
ON
ON
ON
ON
A : SAMSUNG HALF
B : SAMSUNG FULL
SEE INSTRUCTION MANUAL
ON 1 2 3 4 5 6 7 8
SW704
(x100)
(x10)
(x1)
SW701 SW702 SW703
(BOTTOM VIEW)
Baud Rate Setting
Use PIN 5 and 6 of SW704.
1
2
3
4
5
6
7
8
ON
OFF
SW 704
PIN 5
PIN 6
4800 BPS
ON
ON
9600 BPS
OFF
ON
19200 BPS
ON
OFF
38400 BPS
OFF
OFF
BAUD RATE
1-9
The factory default setting is set to 9600BPS.
1-10
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
1-11
Setting RS-422A/RS-485 termination
Chapter 2 SCC-C6407(P) Installation
As it is shown in the structure map, when Controller and RS-422A/RS485 is connected it should be terminated according to the Cable feature
of impedance on the each end of the transmitting line to transfer the
signals in long distance by controlling the reflection of the signals to the
lowest.
Division
n < 32
E
In this chapter, we will check the contents of the package before
installing the SCC-C6407(P), and prepare a power adapter suitable
for the power supply system.
(Power Consumption: 22W; Voltage: AC24V, 1.5A)
Then, we will install the SCC-C6407(P) and connect the cables.
Termination
SW1-ON
<RS-485 Half Duplex Organization>
Termination: using numbers 1 and 2 PIN, turn to ON and it will be terminated.
n < 32
Division
Division
SW1-ON
SW2-ON
<RS-422A/RS-485 Full Duplex Organization>
❈ A communication error may occur if you connect multiple cameras
that are assigned the same address in the network.
1-11
2-1
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
2-2
Preparing the Cables
Before Installing
Checking Package Contents
Please check that all components listed below are included in the package:
To install and use the SCC-C6407(P), the following cables should be
prepared.
Power Adapter Cable
The cable that plugs into the SCC-C6407(P) power input receptacle has
the rated voltage of AC24V, 1.5A.
Check the rated voltage before using the cable.
E
SCC-C6407(P)
Bracket anchor
Owner’s
Instructions
Video Cable
The SCC-C6407(P)'s cable is a BNC Cable for connecting the videooutput terminal to the video-input terminal of the monitor.
Screws
Cover Body
Camera Holder
Adapter Board
2-2
2-3
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
2-4
Installing SCC-C6407(P)
Cable Connection
1. First, connect one end of the
BNC video cable connector to
the Video Output Terminal
(VIDEO OUT)
Installation Precautions
1) Make sure that the installation site can sufficiently support a minimum of
four times the net weight of the SCC-C6407(P) SmartDome Camera
and other accessories.
2) Install in an area where the space above the ceiling board is over 18 cm
(7 in.) high.
3) Use the supplied screws to fasten the camera to the bracket assembly.
4) Keep persons away from the installation area, as there is a risk of falling
objects.
Also, move valuables to a safe location before installation.
2. Then, connect the other end of
the connector to the Video Input
Terminal of the monitor.
E
Separately Sold Products for Installation
3. Now connect the Power Adapter
Cable. Use a driver to screw
one part of the two lines of
Power Adapter to Power Input
Terminal of the SCC-C6407(P).
Depending on the installation site, it may be convenient to use one of the
following products.
1) CEILING MOUNT BRACKET
(SBR-100DCM)
This bracket is used for installing
the SmartDome CAMERA in the
plenum above the drop ceiling.
4. Adjust the switch on the Power Adapter to the proper voltage.
Then, connect the Power Adapter's plug to the Power Connector.
2) WALL MOUNT ADAPTOR
(SADT-100WM)
This adaptor is used for installing the
indoor housing or the outdoor
housing for the SmartDome Camera
on a wall.
5. Connect the Remote Control
Terminal of the
SCC-C6407(P)
and the external Controller.
Controller
Adapter BOARD
2-4
2-5
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
2-6
3) INDOOR HOUSING (SHG-120)
This housing is used for installing the SmartDome Camera to an indoor
wall or a ceiling.
5) CEILING MOUNT ADAPTOR (SADT-100CM)
This adaptor is used for installing the indoor housing or the outdoor
housing for the SmartDome Camera to a concrete ceiling.
E
4) OUTDOOR HOUSING (SHG-220)
This housing is used for installing the SmartDome Camera to an
outdoor wall or a ceiling.
6) POLE MOUNT ADAPTOR (SADT-100PM)
This adaptor is used for installing the WALL MOUNT ADAPTOR
(SADT-100WM) to a pole that is over 8 cm (2.76 in.) in diameter.
❈ To install and use OUTDOOR HOUSING, remove the Clear Case
from the Camera body before installation.
2-6
2-7
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
2-8
Installing the Camera
5. [Figure 5] Match the
BRKT-ANCHOR and CAMERA
ADAPTER and use 4screws
(PH M4 x 8) to assemble them.
1. [Figure 1] Install the structure on the
ceiling.
(Refer to Installation reference
for the Length of the structure)
[Figure 5]
6. Pull the safety wire from the case
body, and assembly it to the
camera holder.
[Figure 6]
* Built in by the builder of the structure
E
[Figure 1]
Length of
ceiling Hole
2. Make a hole in the ceiling where the camera will be installed.
(The hole should be about ø185)
3. [Figure 2] Assemble the
BRKT-ANCHOR on the ceiling
and screw the 4 bolts in.
[Figure 2]
4. [Figure 3,4] Connect the various cables to the CAMERA ADAPTER.
(See page 2-4)
7. [Figure 7] Match the 3 holes on the
back of the CAMERA and the
CONNECTOR and turn it left about
15 degrees.
(Check the sound of LOCKING
and that the LEVER-LOCKING
is in place)
* Use the screws (BH M3 x L8) to
connect the CAMERA and the
ADAPTER so they don't move.
8. [Figure 8] Assemble the
COVER-BODY onto the DOME.
[Figure 7]
[Figure 8]
[Figure 3]
[Figure 4]
2-8
2-9
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-1
Structure of the Setup Menu
CAMERA SET
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
EXIT
ON.../OFF
INT/LINE...
COLOR.../BW.../AUTO...
ON.../OFF
1/2/3/4
OFF/X2~X10
OFF/ON
OFF/ON
QUIT/SAVE/PRESET
IRIS
SHUTTER
AGC/MOTION
EXIT
ALC.../WDR.../MANU...
OFF/1/100(1/120)~10K/AUTOX2...~X160...
OFF/LOW/HIGH (AGC)
S.SLOW/SLOW/NORM/FAST/F.FAST(MOTION)
ATW1/ATW2/AWC/MANU...
ON/OFF
ONEAF/MF
...
REVERSE
OFF/H/V/H/V
Y-LEVEL
(0)l--C-LEVEL
(0)l--DETAIL
(0)l--RET
QUIT/SAVE/PRESET
PRESET
POSITION SET
PRESET ID
VIDEO SET
PRESET SPEED
DWELL TIME
IMAGE HOLD
EXIT
...
ON.../OFF
ON.../OFF
1~8
1~60S
ON/OFF
QUIT/SAVE/DEL
ZONE SET
PRIVACY ZONE
ZONE DIR SET
ZONE AREA SET
EXIT
...
OFF/ON...
OFF/ON...
QUIT/SAVE
AUTO SET
AUTO PAN
PATTERN
SCAN
AUTO PLAY
RET
1.../2.../3.../4...
1.../2.../3...
1.../2.../3.../4...
...
Chapter 3 Setup Menu Overview
In this chapter, we will look over the Setup Menu of the
SCC-C6407(P), First we'll look over the overall structure of the
Setup Menu, and then we'll look at the functions of each menu.
VIDEO SET
WHITE BAL
DIS
FOCUS MODE
SPECIAL
3-1
E
3-2
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
ALARM SET
3-3
ALARM PRIORITY SET
ALARM1~8
EXIT
ALARM IN SET
ALARM1~8
EXIT
NO/NC/OFF
QUIT/SAVE
ALARM OUT SET
ALARM1~8
MOTION
EXIT
1~3
1~3
QUIT/SAVE
AUTO SET
ALARM1~8
MOTION
EXIT
AUX OUT CONTROL
1~8
QUIT/SAVE
OFF/PATTERN1~3/HALF1~2/FULL/SCAN1~4
OFF/PATTERN1~3/HALF1~2/FULL/SCAN1~4
QUIT/SAVE
OUT1
OUT2
OUT3
EXIT
ON/OFF
ON/OFF
ON/OFF
QUIT/SAVE
RET
OTHER SET
PROPOTIONAL P/T
TURBO P/T
AUTO CAL
D-FLIP
CAM RESET
LANGUAGE
PASSWORD
EXIT
ON/OFF
ON/OFF
OFF/6HOUR/12HOUR/18HOUR/24HOUR
ON/OFF
...
ENGLISH/FRANÇAIS/DEUTSCH/ESPAÑOL/ITALIANO
ON.../OFF
QUIT/SAVE
❈ If the power is turned off after PRESET, AUTO PAN, SCAN,
PATTERN function is activated and no other control is made, camera
will do the same function after the power is turned on.
❈ Menu setting is available only when tilt position is under 90°.
When tilt position is over 90° and menu-on command is received,
pan will automatically rotate 180° and tilt will be move to the
corresponding position.
Use the controller to press the MENU selection key and the following
screen will be displayed.
* * MAIN MENU * *
CAMERA SET...
VIDEO SET...
PRESET ...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
➀ PASSWORD
UNDEFINED
0
1
2
3
4
5
6
7
8
9
E
✽✽✽✽
➁ PASSWORD
DEFINED
In case of ➀, use UP/DOWN/LEFT/RIGHT/[ENTER] key for MENU
setup. In case of ➁, type in the 4 digit password first. If correct, the
MENU selection screen like ➀ will be displayed and you will be able to
set up MENU by pressing UP/DOWN/LEFT/RIGHT/[ENTER] key.
SYSTEM INFO
The diagram shown above illustrates the overall structure of the Setup Menu.
In this section, a description of the Setup menu features will enable users of the
SCC-C6407(P) to tailor it to their personal needs.
1. CAMERA SET MENU
CAMERA ID
The CAMERA ID menu assigns an ID to the SCC-C6407(P) to be displayed
on the connected monitor.On the CAMERA SET menu screen, select
CAMERA ID to ON and press [Enter]. You will see the sub screen for
deciding on the ID of the SCC-C6407(P). The Camera ID can have up to
20 alphanumeric characters, along with several special characters.
The assigned camera ID may be positioned to any desired location on the
screen by using the LOCATION submenu.
3-3
3-4
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-5
COLOR/BW
(CAMERA ID)
(CAMERA SET)
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
ON...
INT
COLOR...
OFF
3
OFF
OFF
OFF
EXIT
QUIT
In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter.
In a poor illumination environment, the IR filter is turned off in the BW mode the its
sensitivity increases as high as a black and white camera. On the other hand, the
IR filter is turned on and the sensitivity decreases in the COLOR mode.
COLOR
: The IR Filter is ON and the screen is normal. You can press the
[Enter] key to set the COLOR GAIN LEVEL. And when the AGC
function is on, you can set the AGC COLOER LEVEL.
A BCDEFGHIJKL
M N O PQ R S T U V W X
YZ0 1 2 3 4 5 6 7 8 9
➜
Press
[Enter]
: ! - + ✽ ()/
SP ï î SP
LOCATION...
RET
WDR.DOME.CAMERA.....
* " ... " Means there are Sub Menus.
(CAMERA SET)
V-SYNC
In the V-SYNC menu, vertical synchronization can be selected. The
vertical synchronization signal supported by the SCC-C6407(P) is the INT
mode made by clock inside the SCC-C6407(P) and LINE mode adjusting
vertical synchronization to the exterior power frequency.
Select LINE and press [Enter]. You will see the LINE LOCK submenu
where you can adjust the phase of the LINE LOCK.
You can use the PHASE menu of the LINE LOCK submenu to assign as
much PHASE as you want.
(CAMERA SET)
3-5
(LL-PHASE)
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
OFF
LINE...
COLOR...
OFF
3
OFF
OFF
OFF
EXIT
QUIT
➜
Press
[Enter]
PHASE
RET
(-106)I--------
(COLOR)
CAMERA ID
V-SYNC
COLOR/BW
MOTION
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
OFF
INT
COLOR …
OFF
3
OFF
OFF
OFF
EXIT
QUIT
E
➜
Press
[Enter]
GAIN
AGC COLOR
RET
(0)I-------(0)----I----
BW
: The IR Filter is OFF and the screen is black and white.
(Sensitivity to low light is increased to a level comparable to a black
and white camera.)
Select BW and press [ENTER] and the additional menu to select
BURST ON/OFF will appear.
AUTO
: Select to automatically switch between the COLOR mode and BW
mode depending on the amount of light. In low light conditions, the
IR Filter is turned OFF and the sensitivity to low light is increased
by switching to the BW mode, but in bright light conditions, the IR
Filter is turned ON and the sensitivity is decreased by switching to
the COLOR mode.
Select AUTO and press [ENTER] and the additional menu to select
BW LEVEL and DURATION will appear.
- BURST ON : The color burst signal is output together with black and white
composite video signal.
- BURST OFF : The color burst signal is not output.
- LEVEL
: You can set the brightness level that changes from COLOR mode
to BW mode in 3 steps : LOW, MEDIUM, and HIGH.
- DURATION : Set the HOLDING time for switching between COLOR and BW
mode depending the changes in the amount of light. You can set
the HOLDING time to 10sec (S), 30sec, 60sec, or 300sec( L).
3-6
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-7
❈ In AUTO mode, AGC will be displayed as “---“. You can’t adjust the
settings manually.
(CAMERA SET)
(AUTO)
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
OFF
INT
AUTO...
OFF
3
OFF
OFF
OFF
EXIT
QUIT
➜
Press
[Enter]
BURST
LEVEL
DURATION
RET
ON
LOW
S --|---- L
Caution : If you use an infrared light source while in AUTO mode, AUTO
switching malfunction and camera AF malfunction may occur.
Select ON and press [ENTER] and the MOTION DET additional menu will
appear. The AREA menu, selecting the screen area where the MOTION
detection function will be applied may be selected by PRESET or USER.
Set AREA to PRESET and the MOTION detection function will be applied to
the factory default part.
If you set the AREA menu to USER and press [ENTER], you may vary the
area and position of the area where you want to apply the MOTION detection
function by yourself. Press Left, Right, Up, or Down to select an area area.
Press ENTER and then Left, Right, Up, or Down to select a position. Press
ENTER again to move back to the upper menu.
Use [ENTER] and Left, Right, Up, or Down to move and scale the MOTION
detection area.
Press [ENTER] again and you will escape the AREA setup menu.
Use SENSITIVITY to set up the sensitivity of MOTION detection strength.
The higher, the more sensitive.
AREA
In MOTION DET, you can set the Motion Detection function, Motion Detection
Sensitivity, and the Area of Motion Detection. If the Motion Detection function
is set, the movement of an intruder can be detected. When motion is detected,
it sets off the Alarm signal of the Controller.
(CAMERA SET)
OFF
INT
COLOR...
ON...
3
OFF
OFF
OFF
EXIT
QUIT
AREA
➜
Use the [Left,
Right, Up, Down]
Keys
MOTION DET
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
E
➜
(MOTION DET)
Press
[Enter]
AREA
SENSITIVITY
RET
PRESET...
L ---|--- H
LOCATION
LOCATION
❈ After PAN/TILT/ZOOM/FOCUS/IRIS movement finishes, MOTION DET
function will not work for about 5 seconds to stablize the chage of the
screen.
❈ MOTION detection function operates based on the brightness change
within the setup region. Therefore, erroneous operation may occur
depending on the brightness difference between the background and
the object that is being taken, or the status of the area setup, etc.
ZOOM SPEED
In the ZOOM SPEED menu you can select the speed of the ZOOM Key
(Tele/Wide).
Use the [Left] or [Right] keys in the ZOOM SPEED menu to select
the speed.
1 : Slowest speed
2 : Low speed
3 : High speed
4 : Fastest speed
3-7
3-8
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-9
DIGITAL ZOOM
EXIT
You may set up the digital zoom magnification ratio in the DIGITAL ZOOM
menu. The magnification ratio ranges from OFF to 10. If you set Digital
Zoom of SCC-C6407(P) to max. 10 times, the mode will become the 32 time
optical zoom and you will be able to enlarge a subject by max. 320 times.
Use Left or Right to select a magnification ratio in the DIGITAL ZOOM menu.
The EXIT menu is used to quit the CAMERA SET menu of the
SCC-C6407(P) and return to the MAIN MENU.
- QUIT
: Ignores the changed information and restores the saved
information.
- SAVE : Saves the information of the setting condition of the menu.
- PRESET : Ignores the changed information and restores the initial
factory defaults of the menu.
(CAMERA SET)
(CAMERA SET)
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
OFF
INT
BW...
OFF
3
OFF
OFF
OFF
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
OFF
INT
BW...
OFF
3
X10
OFF
OFF
EXIT
QUIT
EXIT
QUIT
2. VIDEO SET MENU
IRIS
E
There is a function to automatically adjust IRIS to the incoming light level.
Owing to this function, you may set up the brightness level yourself.
The ALC(Auto Light Control) menu allows you for video output level setup.
ALC
DISPLAY ZOOM
In DISPLAY ZOOM, you can display the ZOOM scale on the screen.
Choose the ALC of the IRIS item and press [ENTER] and set he submenu
to the Video Output level and BLC will be shown.The Video Output Level
can be set in the level item using the [Left, Right] keys.
(CAMERA SET)
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
OFF
INT
COLOR...
OFF
4
OFF
ON
OFF
EXIT
SAVE
X020
BLC (Submenu of the ALC menu)
❈ If no change on the ZOOM scale is made for 3 seconds, the
information window will disappear.
If you use a general camera to photograph a subject under backlight or
bright illumination, the subject will be shown dark on the monitor due to
the backlight. BLC(Back Light Compensation) is used to prevent such a
backlight problem to secure distinct images under bright illumination.
Using the [Left, Right] keys, you can set up BOTTOM…, TOP…, LEFT…,
RIGHT…, CENTER… 5 preset areas and the USER…function that can
directly set the areas. For example, for the items in the BLC menu, you
can confirm the preset BOTTOM area by pressing [ENTER] key in the
BOTTOM… status.
(VIDEO SET)
DISPLAY P/T
In DISPLAY P/T, you can display the position of Pan/Tilt on the screen.
(CAMERA SET)
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
OFF
INT
COLOR...
OFF
4
OFF
OFF
ON
EXIT
SAVE
347/060
❈ If no change on the Pan/Tilt position is made for 3 seconds, the
information window will disappear.
❈ It allows an error range of ±2°.
3-9
(ALC)
IRIS
ALC...
SHUTTER
AUTO X2...
MOTION
NORM
WHITE BAL
ATW1
DIS
--FOCUS MODE ONEAF
SPECIAL
...
EXIT
➜
Press
[Enter]
BLC
LEVEL
RET
QUIT
OFF
(0)---- I----
(ALC)
➜
Press
[Enter]
BLC
LEVEL
RET
BOTTOM...
(0)----I----
3-10
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-11
For items in the BLC menu, the user can set the area and location of the
BLC area by pressing [ENTER] key after put the cursor on USER… using
the [Left, Right] key. For AREA items, you can use the [Up, Down, Left,
Right] key to designate the AREA, and then press the [ENTER] key.
You can set the location for areas using the [Up, Down, Left, Right] key in
the LOCATION.
(ALC)
AREA
➜
MANU...
OFF
OFF
ATW1
OFF
ONEAF
...
QUIT
LOCATION
AREA
➜
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
LOCATION
Use [Left, Right] key in the LEVEL menu to control the video output
level(brightness).
WDR
The WDR camera is a state-of-art technology to expand the screen profit,
mostly effective when you photograph both indoor and outdoor. In short,
this function provides you with the distinct reproduction of not only the
indoor but also the outdoor. Press [ENTER] to set up the WDR leve.
(VIDEO SET)
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
LEVEL1
LEVEL2
L---- I ----H
L---- I ----H
RET
- LEVEL 1 : Controls the shutter speed while WDR operates.
- LEVEL 2 : Controls the whole brightness while WDR operates.
MANU
When you press [ENTER] key after selecting MANU in the IRIS item, an
additional screen appears in which you can set manually opening or closing
the IRIS.
3-11
----I----
E
ALC...
OFF
OFF
ATW1
OFF
ONEAF
...
QUIT
Keep pressing both Left and Right in the SHUTTER menu, the speed will
change in the following sequence.
➝ OFF ➝ AUTO X2... ➝ AUTO X4... ➝ AUTO X6... ➝ AUTO X8... ➝ AUTO X12... ➝
AUTOX16... ➝ AUTO X20... ➝ AUTO X40... ➝ AUTO X80... ➝ AUTO X160... ➝ OFF ➝
1/100(1/120) ➝ 1/250 ➝ 1/500 ➝ 1/1000 ➝ 1/2000 ➝ 1/4000 ➝ 1/10K
➝ OFF ➝ AUTO X2... ➝ AUTO X4... ➝ AUTO X6... ➝ AUTO X8... ➝ AUTO X12... ➝
AUTOX16... ➝ AUTO X20... ➝ AUTO X40... ➝ AUTO X80... ➝ AUTO X160...
➜
Press
[Enter]
(00)
❈ In case the IRIS mode is set to WDR, only the following modes are
available.
(WDR)
WDR...
OFF
OFF
ATW1
ON
ONEAF
...
QUIT
LEVEL
RET
(VIDEO SET)
Press
[Enter]
LOCATION
Press the
ENTER
button.
You may designate both the fast electronic shutter speed and low
electronic shutter speed in the SHUTTER menu. The fast electronic
shutter supports 7 shutter speeds from 1/100(1/120) to 1/10K second to
be used for the bright and fast video image. The AUTO slow electronic
shutter supports 10 shutter speeds from x2 to x160 and sets the shutter
speed to be slow In order to make the image on the screen more distinct
and brighter when you photograph under dark illumination. If you want to
sense the light brightness to control the shutter speed to the brightness
automatically, select the AUTO slow shutter.
USER...
(0) ----I----
AREA
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
(MANUAL)
SHUTTER
Press
[Enter]
BLC
LEVEL
RET
(VIDEO SET)
❈ If you set SHUTTER to between AUTO X4... and AUTO X128..., FOCUS mode will be
displayed as “MF“ (the product can operate only in MF mode). You can ’t adjust the
settings manually. If you set it to OFF, 1/100(1/120)/10K or AUTO X2..., the product
will recover the previous FOCUS mode.
❈ If you set SHUTTER to between AUTO X2... and AUTO X128..., DIS will be displayed
as “---“ (it can only operate in Off mode). You can ’t adjust the settings manually. If you
set it to OFF or 1/100(1/120)/10K, the product will recover the previous settings of DIS.
FLICKERLESS
Either NTSC (for 50 Hz)or PAL (for 60 Hz areas)is an anti-flickering system that is designed
to avoid image flickering on the screen due to inconsistency between the vertical
synchronizing frequency of the picture and the flashing frequency of the lightening. If you
select and set AUTO to ON in SHUTTER from VIDEO SET, you can set NTSC or PAL for
your area and the auto shutter speed is fixed at 1/100(1/120) second.
3-12
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-13
(VIDEO SET)
WHITE BAL
(FLICKERLESS)
IRIS
SHUTTER
MOTION
WHITE BAL
DIS
FOCUS MODE
SPECIAL
ALC...
AUTOX2...
NORM
ATW1
--ONEAF
...
EXIT
QUIT
Lights are generally denoted as color temperatures and expressed in
Kelvin (K) units.
The general light color temperatures are shown below.
➜
Press
[Enter]
FLICKERLESS
OFF
RET
10000K
Blue sky
AGC
The AGC menu was designed to provide you with brighter screen supposed you
photographed any subject in the dark resulting in less brighter image than
regulated. AGC menu setup is available only when the SHUTTER menu is set to
Fast Shutter or Off. Press either Left and Right to go to LOW or HIGH and the
AGC function will be activated. LOW is use to lower the maximum AGC GAIN and
HIGH raise the maximum AGC GAIN.
9000K
Rainy
E
8000K
Cloudy
7000K
(VIDEO SET)
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
ALC...
OFF
LOW
ATW1
OFF
ONEAF
...
QUIT
❈ When the COLOR/BW menu of the camera set is set to AUTO...,
AGC will be displayed as “---“. You can’t adjust the settings manually.
6000K
5000K
The MOTION function is available only when the SHUTTER men is set to Slow Shutter
AUTO, being composed of 5 steps, S.SLOW, SLOW, NORM, FAST, F.FAST.
● S.SLOW reduces the amount of AGC as much as possible to monitor subjects with no
immobility in the dark.
● SLOW reduces the amount of AGC to monitor subjects with little immobility in the dark.
● NORM sets the amount of AGC to the middle to monitor mobile subjects in the dark.
● FAST raises the amount of AGC to monitor fast subjects in the dark.
● F.FAST reduces the amount of AGC as much as possible to monitor very fast subjects in
the dark.
When the SHUTTER menu is set to AUTO, press Down to locate the cursor in the MOTION
menu and press Left and Right for MOTION function setup. Press Left to the SLOW side and
Right to the FAST side.
Sunny
4000K
3000K
MOTION
Partly Cloudy
Fluorescent lamp
Halogen lamp
2000K
Tungsten lamp
1000K
Candlelight
(VIDEO SET)
IRIS
SHUTTER
MOTION
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
3-13
ALC...
AUTO X2...
F.FAST
ATW1
--ONEAF
...
QUIT
3-14
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-15
You can select one of four modes for white balance adjustment as follows:
- ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the
color temperature is monitored continuously and thereby white balance is
set automatically. The following are the approximate supported color
temperature ranges in these modes.
ATW1 : 2500K ~ 9300K(✻1)
ATW2 : 2000K ~ 10000K(Mode recommended for sodium lighting)(✻2)
✻ 1. If the color temperature is out of this range in ATW1 mode, proper
white balance may not be obtained. In that case, select ATW2 mode.
✻ 2. In ATW2 mode, if one color is dominated in the shooted area, the
color can be displayed differently.
Therefore, select the mode which is appropriate for the environment.
- AWC(Auto-Tracing White Balance Control): In this mode, accurate white
balance is obtained by pressing [ENTER] while having a white paper in
front of the camera. White Balance data will be maintained after set it
once. AWC mode is best in locations where the color temperature of light
source is constant.
- MANU : If WHITE BAL menu is set to MANU mode, the user can set the
white Balance considering the current illumination. Select MANU item
and press [ENTER], the sub screen where you can select Manual White
Balance will be shown. Use the left/right keys to select 3200K, 5600K or
OFF(USER) mode in the PRESET menu.
- 3200K : Set color temperature to 3200K
- 5600K : Set color temperature to 5600K
- USER : Choose out a proper value from the RED and BLUE graph for
color and temperature setup.
(VIDEO SET)
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
FOCUS MODE
In the FOCUS MODE MENU, the Focus method can be set to ONEAF(One Auto
Focus), or MF(Manual Focus).
- ONEAF : In the ONEAF mode, it automatically sets the focus after the zoom moves,
and operates as the same in the MF mode if the zoom does not move.
- MF
: In MANUAL FOCUS MODE the user adjusts the Focus manually.
Use the left/right keys to select ONEAF orMF in the FOCUS MODE menu.
(VIDEO SET)
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
ALC...
OFF
LOW
ATW1
OFF
ONEAF
...
QUIT
❈ The ONEAF setting can be selected only when OFF,
1/100(1/120)~1/10K, AUTO X2 is selected for the SHUTTER menu. Any
Other SHUTTER setting(AUTO X4~AUTO X160) causes MF to be
selected automatically for the FOCUS MODE menu.
❈ ONEAF function may not possible withe types of objects listed below. For
such objects, focus manually.
- High intensity objects or objects illuminated with low lighting
- Obejects shot through wet or dirty glass
- Pictures that are a mixture of distant and nearby objects
- White alls and other single-color objects
- Venetian blinds and other horizontally striped objects
(AWB/MANU)
ALC...
OFF
ON
MANU...
ON
ONEAF
...
QUIT
SPECIAL
➜
Press
[Enter]
PRESET
3200K
RET
DIS
The DIS(Digital Image Stabilization) function compensates the camera
screen shaking incurred from vibration.
In SPECIAL menu, you can directly adjust REVERSE, Y-LEVEL, C-LEVEL,
and DETAIL functions.
- REVERSE : Mirrors the screen horizontally, vertically, or in all directions.
- Y-LEVEL : It is used to set the levels for the Sync signal and the entire
brightness signal of the video signal.
- C-LEVEL : It is used to set the levels for the Burst signal and the entire colour
signal of the video signal.
- DETAIL : Controls both horizontal and vertical distinction.
(VIDEO SET)
❈ It is recommended to deactivate the DIS function in the no vibration
environment.
❈ From VIDEO SET, if you set SHUTTER to between AUTO X2... and
AUTO X128... DIS will be displayed as “---“ (it can operate only in
Off mode). You can’t adjust the settings manually.
3-15
E
(SPECIAL)
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
ALC...
OFF
LOW
ATW1
OFF
ONEAF
...
EXIT
QUIT
➜
Press
[Enter]
REVERSE
Y-LEVEL
C-LEVEL
DETAIL
RET
OFF
(0)I-------(0)I-------(2)--I-
3-16
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-17
EXIT
POSITION SET
It's the same as the EXIT function of the CAMERA SET menu.
From "POSITION SET..." press [ENTER] to get into the PAN/TILT,
FOCUS/ZOOM SET screen
to set the PAN/TILT location and FOCUS/ZOOM condition then press
[ENTER] to return to a higher menu.
3. PRESET
PRESET ID
This is the menu that user sets the PAN/TILT location, Zoom/Focus, and
screen condition, so the camera can monitor the presetting area on
demand. A total of 128 presets are available.
This is the ID set up function for each PRESET.
It can be set up to 12 characters using the left, right, up, and down keys.
The ID location can be set in the submenu of "LOCATION..."
E
VIDEO SET
This is the screen setting function for each PRESET.
Refer to the explanation under "VIDEO SET menu".
* * MAIN MENU * *
CAMERA SET...
VIDEO SET...
PRESET ...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
(PRESET MAP)
➜
Press
[Enter]
PRESET SPEED
0 1 2 3 4
5 6 7 8 9
10 11 12 13 14
15 16 17 18 19
20 21 22 23 24
25 26 27 28 29
30 31 î ï RET
ID:PRESET 0
This function sets up the speed of PAN or TILT by 8 steps from 1(SLOW)
to 8(FAST).
- PRESET SPEED 1 : Maximum PAN moving speed of 240°/sec
- PRESET SPEED 8 : Maximum PAN moving speed of 400°/sec
DWELL TIME
This is a function setting for the DWELL TIME of the PRESET location in
"SCAN" motion. It can set DWELL TIME From 1 ~ 60 Sec.
PRESET NO.0
➜
Press
[Enter]
IMAGE HOLD
POSITION SET
PRESET ID
VIDEO SET
PRESET SPEED
DWELL TIME
IMAGE HOLD
...
ON...
OFF
8
3S
OFF
Pauses the image when PRESET is in movement, If you set the IMAGE
HOLD menu to ON, the screen will be paused until PRESET finishes
moving.
EXIT
QUIT
EXIT
❈ Set the PRESET position at the TILT which ranges from 0° to 90°. Beyond
this range, PRESET setup is not available.
"QUIT" : Does not save the selected information and returns to a higher
menu.
"SAVE" : Do saves the selected information and returns to a higher menu.
"DEL" : Deletes the selected information and restores the DEFAULT.
Then returns to a higher menu.
❈ When you try to set the Preset position by using the Controller(SSC-1000
or SSC-2000) beyound the range of TILT 90°, the text, “SET AGAIN” will
be displayed. In such a case, please retry in the area below TILT 90°.
3-17
3-18
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-19
BLANK ALL ABOVE
4. ZONE SET
The ZONE SET menu includes the setup of PRIVACY ZONE, ZONE
DIRECTION, and ZONE AREA.
The available angle for setup ranges from OFF/0/-10 to -90 and the area
above a set angle will be regarded as the ZONE area.
BLANK ALL BELOW
* * MAIN MENU * *
CAMERA SET...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
(ZONE SET)
➜
Press
[Enter]
PRIVACY ZONE
ZONE DIR SET
ZONE AREA SET
...
ON...
OFF
The available angle for setup ranges from OFF/0/-10 to -90 and the area
below a set angle will be regarded as the ZONE area.
E
PRIVACY ZONE MAP
EXIT
QUIT
PRIVACY ZONE
Move PAN/TILT/ZOOM to select an area that can infringe someone
privacy, then this function will hide the area if it can be involved in the
photograph to protect his privacy. The number of area reaches up to 12.
Press [ENTER] to enter the PRIVACY ZONE MAP screen from
“PRIVACY ZONE MAP ON..”.
Select a privacy zone number and press [ENTER] from the PRIVACY
ZONE MAP screen to enter the PRIVACY ZONE setup screen.
(PRIVACY ZONE SET)
STYLE
MOSAIC1
BLANK ALL ABOVE OFF
BLAK ALL BELOW
OFF
PRIVACY ZONE MAP ON...
STYLE
In the STYLE menu, you may the shape of the PRIVACY ZONE area on the
screen.
- MOSAIC1 : The privacy zone is displayed with the mosaic of 16 X 16 pixel.
- MOSAIC2 : The privacy zone is displayed with the mosaic of 32 X 32 pixel.
EXIT
(PRIVACY ZONE MAP)
➜
EXIT
QUIT
2
8
3
9
4 5
10 11
RET
QUIT
PRIVACY ZONE SET 0
(PRIVACY ZONE SET)
MOSAIC1
OFF
OFF
ON...
1
7
Press
[Enter]
➜
STYLE
BLANK ALL ABOVE
BLANK ALL BELOW
PRIVACY ZONE MAP
0
6
SET ZONE AREA
SET ZOOM
REVERSE
ON...
...
ON
EXIT
QUIT
Press
[Enter]
❈ Set to the PRIVACY ZONE section, the mosaic screen will not be
recovered after recording.
3-19
3-20
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-21
SET ZONE AREA
SET ZOOM
Press [ENTER] at the “SET ZONE AREA...” position to enter the
PRIVACY ZONE setup screen. Control PAN/TILT/ZOOM to select 4
apexes of the PRIVACY ZONE area and the rectangular PRIVACY
ZONE area will be completed.
Press [ENTER] at the “SET ZOOM...” position to enter the ZOOM setup
screen. After ZOOM setup, the PRIVACY ZONE function will be in action
only at the higher magnification than the Zoom magnification
as set.
PRIVACY ZONE SET 0
SET ZONE AREA
SET ZOOM
REVERSE
ON...
...
OFF
➜
➜
PRIVACY ZONE P/T 2
PRIVACY ZONE P/T 3
➜
After P/T/Z
control, press
[ENTER]
SET ZOOM
ON...
...
OFF
➜
Press
[Enter]
EXIT
QUIT
●
SET ZONE AREA
SET ZOOM
REVERSE
After P/T/Z
control, press
[ENTER]
●
Press
[Enter]
EXIT
PRIVACY ZONE SET 0
PRIVACY ZONE P/T 1
●
E
QUIT
REVERSE
The REVERSE function applies PRIVACY MASK to the other area than
set as a privacy zone. ON/OFF is available.
PRIVACY ZONE SET 0
SET ZONE AREA
SET ZOOM
REVERSE
ON...
...
ON
PRIVACY ZONE P/T 4
➜
After P/T/Z
control, press
[ENTER]
❈ For the safer privacy protection, select about 10 % more than the
actual area to hide when you set up the PRIVACY ZONE area.
❈ 4 points of PRIVACY ZONE area are in the middle of the screen.
Therefore, when the tilt is positioned at upside limit(0° or 180°),
PRIVACY ZONE cannot be set in the area which is displayed
above center.
❈ If the points becomes X shape, it means PRIVACY ZONE cannot
be set due to the area limitation.
3-21
EXIT
●
QUIT
EXIT
"QUIT" : Does not save the selected information and returns to a higher
menu.
"SAVE" : Do saves the selected information and returns to a higher menu.
"DEL" : Deletes the selected information and restores the DEFAULT.
Then returns to a higher menu.
ZONE DIR SET/ZONE AREA SET
This function indicates the ID or direction depending on the set value
when PAN of SCC-C6407(P) is located in a specific area. If set to AREA,
it indicates the ID of the selected area and if set to N(NORTH), NE(NORTHEAST), E(EAST), SE(SOUTH-EAST), S(SOUTH), SW(SOUTH-WEST), W(WEST),
NW(NORTH-WEST.
3-22
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-23
ZONE DIR SET
LOCATION
Press the [Enter] key in the “ZONE DIR SET ON…” mode to enter the
NORTH SET screen. MAP. Move PAN to set the NORTH position and
press [ENTER]. Based on the North position,the direction of N(North),
NE(North-East), E(East), SE(South-East), S(South), SW(South-West),
W(West), NW(North-West) is displayed whenever you move PAN.
The “LOCATION...” menu designates the left/right LIMIT positions of
ZONE AREA. Enter the setup screen to move PAN, then select a start
position and press [ENTER]. Move PAN again
to select a end position and press [ENTER]. Now, ZONE AREA setup is
complete.
(ZONE SET)
PRIVACY ZONE
ZONE DIR SET
ZONE AREA SET
ZONE AREA SET 0
SET NORTH
...
ON...
OFF
SET START!
LOCATION
ZONE ID SET
ZONE ENABLE
➜
...
...
ON
N
Press
[Enter]
EXIT
QUIT
EXIT
ZONE AREA
➜
➜
Press
[Enter]
After P/R/Z
control, press
[ENTER]
E
QUIT
SET END!
Press [ENTER] to enter the ZONE AREA MAP screen from “ZONE
AREA SET...”. Select a ZONE AREA number from the ZONE AREA MAP
screen and press [ENTER] to enter the ZONE AREA setup screen.
(ZONE SET)
After PAN control,
press [ENTER] to
finish.
(ZONE AREA MAP)
PRIVACY ZONE
ZONE DIR SET
ZONE AREA SET
...
OFF
ON...
0*
4
➜
Press
[Enter]
EXIT
QUIT
RET
1
5
2
6
3
7
ZONE ID SET
This function is used to allocate as many as 12 IDs to each zone area.
Use Left , Right, UP, or DOWN for this purpose. You may select the ID
position from the additional menu of “LOCATION...”.
ZONE AREA ID 0
ZONE AREA SET 0
ZONE AREA SET 0
➜
LOCATION
ZONE ID SET
ZONE ENABLE
...
...
ON
LOCATION
ZONE ID SET
ZONE ENABLE
...
...
ON
Press
[Enter]
Press
[Enter]
EXIT
EXIT
➜
A BCDEFGHI J K L
MNOPQRSTUVWX
Y Z 012345678 9
: ! - + ✽ ()/
SP ï î SP
LOCATION...
RET
ZONE 0........
QUIT
QUIT
ZONE ENABLE
This function turns on or off the ZONE AREA ID indication.
3-23
3-24
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-25
5. AUTO SET
DIRECTION
The AUTO SET menu includes AUTO PAN, PATTERN, and SCAN and it
is able to set up the AUTO PLAY motion.
This sets up the movement direction of the START to END location
(PAN location standard)
"RIGHT " :
"LEFT " :
AUTO PAN
After selecting the locations of two points (PAN/TILT) of START and END,
it loops continuously in the set up SPEED. The number of AUTO PAN is
up to 4.
E
* * MAIN MENU * *
CAMERA SET...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
(AUTO SET)
➜
Press
[Enter]
AUTO PAN
PATTERN
SCAN
AUTO PLAY
1...
1...
1...
...
RET
Press
[Enter]
This is a 360-degree rotation function that stops for the DWELL TIME only in the
START and END positions without running between the START and END
positions. It can be set to "ON" or "OFF".
SPEED
This is a setting function for movement speed setup. It can be set from
STEP1 to STEP64.
AUTO PAN 1
➜
ENDLESS
POSITION SET
DIRECTION
ENDLESS
SPEED
DWELL TIME
...
RIGHT
ON
32
3S
EXIT
QUIT
DWELL TIME
This is a function for setting up the time to stay in the START to END position.
PATTERN
This is a replay function so that the MANUAL functions such as PAN, TILT,
ZOOM, and FOCUS are played for 2 minutes.
POSITION SET
The menu “POSITION SET …” sets the Start / End position of AUTO PAN.
Return to the settings screen and set the desired START position for
PAN/TILT, and then press the [ENTER] key. And, set the END position for
the PAN/TILT. Press the [ENTER] key to finish the setup for AUTO PAN
Start/End positions.
3-25
❈ When the PATTERN is saved/executed, the PAN/TILT is operated with
PROPORTIONAL ON, TURBO OFF.
❈ If the SSC-1000 or SSC-2000 is used when uploading/downloading the
menu setup, reset the PATTERN because it may be different with the first
setting.
3-26
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
* * MAIN MENU * *
CAMERA SET...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
3-27
AUTO PLAY
(AUTO SET)
AUTO PAN
PATTERN
SCAN
AUTO PLAY
➜
Press
[Enter]
1...
1...
1...
...
➜
Press
[Enter]
RET
➜
PATTERN SET 1
SET START POSITION
AND ENTER
(AUTO SET)
AUTO PAN
PATTERN
SCAN
AUTO PLAY
PATTERN SET 1
After PATTER
START
position setup,
press
[ENTER].
SCAN
SCAN sets the direction of PRESET movement during “SCAN” operation. The
number of SCAN is up to 4 and each SCAN is able to allocate 32 PRESETs as a
maximum.
1...
1...
1...
...
➜
Press
[Enter]
AUTO RETURN 12HOUR
AUTO PLAY
SCAN
PLAY NUMBER 1
E
QUIT
AUTO RETURN
This menu sets up the time during which AUTO PLAY repeats.
AUTO PLAY
This function sets up the motion which will be repeatedly performed by
SCC-C6407(P) whenever the time set by AUTO RETURN elapses. It covers
SCAN, AUTO PAN, PATTERN, and PRESET setup.
PLAY NUMBER
This menu allocates a number to the motion set by AUTO PLAY. The numbers
range from 1 to 4 for SCAN AND AUTO PAN, 1 to 3 for PATTERN, and 0 to 127
for PRESET.
SCAN MAP 1
(AUTO SET)
RET
(AUTO PLAY SET)
RET
PATTERN can be set upto 3. Choose 1, 2, or 3 with the left or right key in the
"PATTERN SET" and press [ENTER] to get into the PATTERN set up screen. From
the moment "PATTERN 1 SET" is gone for 2 minutes, it memorizes the MANUAL
movements and after 2 minutes it will return to a higher menu. If you want to finish
set up before the 2-minutes ends, press [ENTER].
AUTO PAN
PATTERN
SCAN
AUTO PLAY
AUTO PLAY executes SCAN, AUTO PAN, PATTERN, and PRESET when there
is no camera action after AUTO RETURN finishes.
1...
1...
1...
...
➜
Press
[Enter]
0*S 1*
2
5
6
7
10 11 12
15 16 17
20 21 22
25 26 27
30 31 î
EXIT
3
8
13
18
23
28
ï
4
9
14
19
24
29
SAVE
If you enter the SCAN SET screen, SCAN MAP will be displayed. Move the cursor
to the number marked * where PRESET is saved and press [ENTER] and
S will appear and a PRESET will be included in SCAN.
3-27
3-28
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-29
AUTO SET
6. ALARM SET
It consists of 8 ALARM INPUTs and 3 ALARM OUTs.It can sense an
ALARM input from exterior SENSORs and it performs with PRESET or
PATTERN function and outputs the ALARM OUT signals.
Alarm operation time depends on the Preset Dwell time corresponding to
the alarm and whether AUTO is involved.
* * MAIN MENU * *
CAMERA SET...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
( ALARM SET)
➜
Press
[Enter]
ALARM PRIORITY SET ...
ALARM IN SET..
ALARM OUT SET..
AUTO SET..
AUX OUT CONTROL..
RET
ALARM PRIORITY SET
This sets the priority of the 8 ALARM inputs so ALARM can work
corresponding to the priority.
The priority of the DEFAULT is ALARM1, ALARM2, ALARM3, ALARM4,
ALARM5, ALARM6, ALARM7, ALARM8.
If the ALARM is working at the same time and the priority is the same, it
will operate according to the DEFAULT priority. While the ALARM is
working, it cannot detect MOTION.
ALARM IN SET
This sets the input TYPE to "NO" (Normal Open), "NC" (Normal Close), or
"OFF" depending on the features of the SENSOR connected.
ALARM OUT SET
Each ALARM input corresponds to one of the 3 ALARM OUT.
3-29
This menu designates what to do at the time of ALARM input. Once an
alarm is given, the camera will shortly move to the PRESET position
corresponding to the respective alarm as follows.
PRESET1 to ALARM1~8
PRESET9 to MOTION
After DWELL TIME at a PRESET position, PATTERN or SCAN will be in
action according to the AUTO SET setup.
Setup of OFF/1/2/3/HALF1/HALF2/FULL/SCAN1~4 is available.
OFF dues not perform PATTERN or SCAN after moved to PRESET and
each menu has its own function as follows.
PATTERN 1~3 : Preset PATTERN action,
HALF1 : Continuous operation of PATTERN1 + PATTERN2
HALF2 : Continuous operation of PATTERN2 + PATTERN3
FULL : Continuous operation of all the aboves
SCAN 1~4 : Scanning as set
E
AUX OUT CONTROL
This sets the ALARM OUT motion to continue or act only when the
ALARM is working.
If it is set to OFF the ALARM OUT motion will operate only when the
ALARM is working.
(Active "Low"), and if it's set to ON, the ALARM OUT will always operate
regardless of the ALARM.
7. OTHER SET
PROPORTIONAL P/T
This function controls the PAN/TILT speed to the ZOOM magnification
ratio during the manual operation of PAN/TILT. If you set
PROPORTIONAL P/T to ON, the PAN/TILT speed will increase in the
ZOOM WIDE mode and decrease in the ZOON TELE mode even in the
same manual operation.
3-30
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-31
TURBO P/T
This function doubles up the speed of PAN/TILT movement by manual
operation of PAN/TILT. The speed may go up to 180°/sec(PAN).
AUTO CAL
This function turns on or off Auto Calibration. SCC-C6407(P) has the Auto
Calibration function to improve the precision of LENS and PAN/TILT
motor. You may set to OFF/6H/12H/18H/24H. Without user’s key input for
the time designated by the user, A.C. will appear on the screen while
initializing LENS and PAN/TILT.
D-FLIP
When D-FLIP is off, TILT movement ranges from 0° to 90°.
When D-FLIP is on, TILT movement ranges from 0° to 180°.
When D-FLIP is on, images mirror vertically and horizontally in the area
beyond TILT 90°.
CAM RESET
CAM RESET clears all the settings made so far and restores the factory
default settings.
"CAMERA RESET?" message appears when you select CAM RESET.
Select "CANCEL" to return to the menu setup display or select OK to
restore the factory default settings.
❈ Be careful when performing a CAM RESET operation, as it deletes all
setup values.
LANGUAGE
This function selects a language for MENU setup. Press UP/DOWN key to
choose English, French, German, Spanish, or Italian, and the selected
language will be applied to the full screen.
(PASSWORD)
(OTHER SET)
PROPORTIONAL P/T
TURBO P/T
AUTO CAL.
D-FLIP
CAM RESET
LANGUAGE
PASSWORD
EXIT
ON
OFF
OFF
ON
...
ENGLISH
ON...
➜
0
1
2
3
4
5
6
7
8
9
Press
[Enter]
✽✽✽✽
✽✽✽✽
RET
QUIT
Press UP/DOWN/LEFT/RIGHT key to locate the cursor on a number and
press [ENTER] for password setup. After you finish inputting the 4 digits
password and the 2nd row of the 4 digits PASSWORD input screen, input
the selected password again for reassurance.
If correct, the cursor will move to RET.
Press [ENTER] at RET, and the selected password will be saved,
returning to the OTHER SET screen.
Default password is 0123.
E
8. SYSTEM INFO
This menu allows you to check S/W version, communication protocol,
baud rate, and address of SCC-C6407(P).
* * MAIN MENU * *
CAMERA SET...
VIDEO SET...
PRESET...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
➜
Press
[Enter]
( SYSTEM INFO)
FPGA VER.
V1.000
ALARM VER. V1.000
MOTOR VER. V1.000
CAMERA VER. V1.000
EEPROM VER. V1.000
PROTOCOL
SAMSUNG
COMM. TYPE RS-485, HALF
BAUD RATE
38400
ADDRESS
0
SERIAL NO.
000000000000000
RET
PASSWORD
This function selects or cancels the MENU setup password. Press
[ENTER] at the state of PASSWORD ON, and the following screen will
appear for password setup.
3-31
3-32
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-33
9. SHORT KEYS
SSC-1000 or SSC-2000 Controller supports the following short keys.
Function
* SCC-C6407(P) has two FANs inside for preventing overheating.
If FAN doesn't work properly, messages below will be displayed.
In those case, replace the FAN.
Key
CAMERA SET…
COLOR/BW
COLOR
[PRESET] + [1] + [2] + [8] + [Enter]
COLOR/BW
BW
[PRESET] + [1] + [2] + [9] + [Enter]
COLOR/BW
AUTO
[PRESET] + [1] + [3] + [0] + [Enter]
IRIS
WDR
[PRESET] + [1] + [3] + [1] + [Enter]
IRIS
ALC
[PRESET] + [1] + [3] + [2] + [Enter]
FOUCS MODE
ONEAF
[PRESET] + [1] + [3] + [5] + [Enter]
FOCUS MODE
MF
[PRESET] + [1] + [3] + [4] + [Enter]
OUT1
ON
[PRESET] + [1] + [3] + [6] + [Enter]
OUT1
OFF
[PRESET] + [1] + [3] + [7] + [Enter]
OUT2
ON
[PRESET] + [1] + [3] + [8] + [Enter]
OUT2
OFF
[PRESET] + [1] + [3] + [9] + [Enter]
OUT3
ON
[PRESET] + [1] + [4] + [0] + [Enter]
OUT3
OFF
[PRESET] + [1] + [4] + [1] + [Enter]
PROPORTIONAL P/T
ON
[PRESET] + [1] + [4] + [2] + [Enter]
PROPORTIONAL P/T
OFF
[PRESET] + [1] + [4] + [3] + [Enter]
TURBO P/T
ON
[PRESET] + [1] + [4] + [4] + [Enter]
TURBO P/T
OFF
[PRESET] + [1] + [4] + [5] + [Enter]
D-FLIP
ON
[PRESET] + [1] + [4] + [6] + [Enter]
D-FLIP
OFF
[PRESET] + [1] + [4] + [7] + [Enter]
VIDEO SET…
- CAMERA FAN ERROR !
: This message is displayed when the FAN which is connected with camera of
SCC-C6407(P) does not work properly.
- ALARM FAN ERROR !
: This message is displayed when the FAN which is located bottom of
SCC-C6407(P) does not work properly.
E
Contact your nearest Samsung Electronics Service Center or designated retailer
before replacing the FAN.
ALARM SET…
AUX OUT CONTROL…
OTHER SET…
AUTO RETURN *1)
[PRESET] + [1] + [4] + [8] + [Enter]
AUTO CAL.
[PRESET] + [1] + [4] + [9] + [Enter]
CAM RESET
[PRESET] + [1] + [5] + [0] + [Enter]
Other keys than AUTO CAL. and AUTO RETURN, upon execution, shall
be applied to the MENU setup process.
*1) The use of AUTO RETURN will be available only when the function
equivalent to AUTO PLAY, a sub menu of AUTO SET has been built in.
3-33
3-34
00547A-SCC-C6407P-ENG 8/17/063:24PM ˘`
3-35
Product specifications
Cautions
SCC-C6407P
3-35
NO
Items
1
Product Type
2
Power Input
3
Power Consumption
4
Broadcasting Type
5
Image Device
Contents
Remark
- Zoom lens single body WDR SmartDome CAMERA
• The copyright of the manual belongs to Samsung Electronics Co., Ltd.
• Without the permission of Samsung Electronics it cannot be reproduced
electronically, mechanically, audibly, or by any other method.
- AC 24 ± 10% (50Hz ± 0.3Hz)
- 22W
• This manual will be modified according to product enhancements.
- PAL STANDARD COLOR SYSTEM
- 1/4 inch WDR compatible Exview HAD CCD
6
Effective Pixels
- 752(H) x 582(V)
7
Scanning Mode
- 625 Lines, 2:1 Interlace
8
Scanning line Frequency
9
Synchronization Mode
10
Resolution
- 480 TV LINES
11
S/N Ratio
- 50dB (AGC OFF)
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
- Horizontal : 15, 625Hz(INT) / 15, 625 Hz(L/L)
- Vertical : 50 Hz(INT) / 50 Hz(L/L)
- INT/LINE LOCK
(Applicable in the European Union and other European countries with
separate collection systems)
- COLOR : 0.18 Lux (SENS UP X4)
0.005 Lux (SENS UP X160)
- B/W : 0.018 Lux (SENS UP X4)
0.0005 Lux (SENS UP X160)
12
Min. Object Illumination
13
WDR
14
Color Temperature
15
Signal Output
16
Lens
17
PAN Function
- PAN range : 360° Endless
- Preset Pan Speed : 400° /sec, maximum
- Manual Pan Speed : 0.1° ~ 180° /sec (64Step)
18
TILT Function
- TILT range : 0° ~ 180°
- Preset Tilt Speed : 200° /sec, maximum
- Manual Tilt Speed : 0.1° ~ 90° /sec (64Step)
19
REMOTE CONTROL
20
ALARM
21
Operation Temperature
22
Operation Humidity
23
SIZE
24
Weight
25
Lives of Main Parts
This marking shown on the product or its literature, indicates that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly
to promote the sustainable reuse of material resources.
- 128
- ATW1/ATW2/AWC/MANUAL MODE
(3200K, 5600K, R/B GAIN Court)
- COMPOSITE VIDEO OUT : 1.0 Vp-p 75 ohms/BNC
- one body; 32x Zoom lens
- Focal length : 3.55 to 113 mm
- Aperture : F1.69(Wide), F4.17(Tele)
- MOD(Minimum Object Distance) : 2.5m
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
- Tele/Wide(ZOOM), NEAR/FAR(FOCUS),
Iris Open/Close, Pan/Tilt, MENU
RS-485 HALF/FULL Duplex, RS-422
- Alarm Inputs : 8 IN(5mA Sink)
- Alarm Outputs : 3 OUT (Open collector : 2
DC24V 40mA Max, Relay : 1, NO, NC, COM
2A 30VDC, 0.5A 125VAC Max)
- -10°C ~ +50°C
- ~90%
- DOME : 147 (ø),
- Outline : 159.6(ø) x 177(H)
- 1.7Kg
- Slip-ring
Rotated
10,000,000
Times
- Fan
4.5 Years
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising