XP-600 Programming Instructions

XP-600 Programming Instructions
XP-600 Programming Instructions
®
Note: These Programming Instructions are intended to be used in conjunction with WI1372,
please refer to WI1372 for additional information, instructions and definitions.
DEALER PROGRAM MODE
NOTE:
DEFAULTING THE PANEL
After 15 minutes of keypad inactivity, the keypad
will emit a steady tone indicating the panel has
been left in Dealer Program Mode. Enter Dealer
Code to exit or press the B key to return to
Dealer Program mode.
1. Remove power from the panel.
2. Remove all wiring from terminal 15
(PGM) and terminal 3.
3. Connect terminal 15 (PGM) to
terminal 3.
4. Apply power to the XP-600 control
panel.
5. After a few seconds the ARMED,
READY and HSYSTEM TROUBLE
LEDs will flash.
6. The keypad will beep 3 times
indicating the panel default values
have been loaded.
7. Remove wiring between terminal 15
(PGM) and terminal 3.
8. Re-install original wiring for terminal
15 (PGM) and terminal 3.
- KEYPAD KEY DEFINITIONS
Hexadecimal Data Entry
To Enter a hexadecimal digit
enter the following:
A=
B=
C=
A1
A2
A3
D=
E=
F=
Set Key
Press this key before
entering a Programming
Block Number.
A4
A5
A6
Blank Key
Press this key to disable all
features within a LED type
Programming Block or to blank out
digits in a Direct Entry type
Programming Block.
Scroll Key
Use this key to scroll
through data that has
been
entered
in
Programming Blocks.
Dealer Code
ARMED (ON)
Entering Dealer Program Mode
Enter A 8
READY (OFF)
(4) (5) (6) (7)
NOTE:
Entering Dealer Program Mode is not permitted while the panel
is Armed, Reporting, or the Bell Output is on. To Enter Dealer
Mode while the Bell is ON or the panel is Reporting or Armed;
power up the panel and enter Dealer Mode within the first 3
minutes. Pressing the b key clears the 3 minute timer.
Exiting Dealer Program Mode
SYSTEM (FLASHING)
Note: Any programming in Dealer
Options 1 [96] and Dealer Options 2
[97] will not be defaulted. If Dealer
Code Lockout has been
programmed the panel will not
default the Dealer Code. The Event
Log will be erased when the panel
is defaulted.
Indicates the panel is in Dealer
Program Mode. The panel is
ready for a programming block
number to be entered.
Default Dealer Code shown in parentheses
ARMED (FLASHING)
Dealer Code
Enter B A 8
READY (FLASHING)
SYSTEM (FLASHING)
Indicates the panel is Ready
to exit
Dealer Program
Mode.
Enter the Dealer
Code to exit.
(4) (5) (6) (7)
© NAPCO 2005
WI1373 1/05
Types of Programming Blocks
LED Programming Block
Enable features by pressing the key that corresponds to the associated feature; the LED will turn ON. To disable a feature press the key
again; the LED will turn OFF. To disable all features within a LED Type Programming Block press the D key; all LEDs will turn OFF.
1
LED Programming Block Example
Program zones 2 and 3 as Follower Zones.
02 Exit/Entry Follower
OFF
1. Enter Programming Block 02, by pressing
B (Beep), then 02 (Beep).
2. Press the 2 key to select zone 2.
3. Press the 3 key to select zone 3.
Zone 2 and Zone 3
LED Type
are
ON
Programming LEDs
indicat in g
that
Block
zones 2 and 3 have
been programmed
as follower zones.
Default
OFF
!
OFF
!
OFF
OFF
OFF
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Direct Entry Programming Block
Enter data directly. For hexadecimal entries of A-F, use the A key + 1 through 6 keys, respectively. Use the
D
1
key to blank out digits in Direct Entry type programming blocks. Default values are shown in parentheses.
Direct Entry Programming Example 1
Program the panel for a 60 second Exit Delay.
1. Press B (Beep) 10 (Beep)
2. Press 060.
10 Exit Delay
0
6
0 Exit Delay, seconds
(0) (4) (5) Maximum Entry 255
44 Dialing Prefix
2
9
E
Direct Entry Programming Example 2
(Hexadecimal data entry)
Program Telephone Prefix Number with a 9E.
1.
2.
3.
4.
2
Direct Entry
Type
Programming
Blocks
Press B (Beep) 44 (Beep).
Press 9
Press A
Press 5
ARMED (OFF)
READY (FLASHING)
SYSTEM (FLASHING)
Indicates the panel is in
Dealer Program Mode and
the next digit entered will be
interpreted
as
a
Hexadecimal digit.
Valid
entries are 1-6 (A-F).
Viewing Data in Programming Blocks
To view data within a programming Block, enter the Program Block Number, then press the C key, continue pressing the C key until all digits within
the Programming Block have been viewed. Data will be displayed in the binary format shown in the table below:
0/Blank
1
2
3
4
5
6
7
8
9
*A/0
B
C
D
E
F
*
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE LED ON
For Technical
Assistance,
Contact the Napco
Toll Free Helpline
!
(800) 645-9440
44 Dialing Prefix
Data = 9
Press the B key to view the 2nd digit.
9
E
NOTE:
The Following Programming
Options are not permitted for
UL installations: [05], [06], [232], [26-3] and [26-4].
T h e UL s y m b o l
by
a
programming Block indicates
the programming option is not
permitted for UL installations.
Press B44 to enter Programming Block 44. The 1st
digit of Programming Block 44 is displayed.
2
In
the
following
Programming Blocks, data
that has been entered as a
‘0’ will be displayed as an
‘A’:
Subscriber ID
Numbers,
Phone
Numbers, Pager Leading
and Trailing digits and
Report Codes.
ZONE LED OFF
Example: Viewing the Dialing Prefix
A Dialing Prefix of 9E has been programmed at Programming Block
Number 44 (outside access number). Follow the steps below to view the
data.:
1
NOTE:
Data = E
NOTE:
For information about
programming blocks
refer
to
XP-600
Installation
Manual
WI1372.
3
Zone Features
03 Auto Bypass Reentry Zones
00 Exit/Entry Zones
Default
Default
06 Open Circuit Zones
Default
Zone 1
OFF
Zone 1
OFF
Zone 1
OFF
Zone 2
OFF
Zone 2
OFF
Zone 2
OFF
Zone 3
OFF
Zone 3
OFF
Zone 3
OFF
OFF
OFF
Zone 4
Zone 5
OFF
OFF
Zone 4
Zone 5
OFF
Zone 4
Zone 5
OFF
Zone 6
OFF
Zone 6
OFF
Zone 6
04 24 Hour Protection Zones
Default
Default
Default
Zone 1
OFF
Zone 1
ON
Zone 1
OFF
Zone 2
OFF
Zone 2
ON
Zone 2
OFF
Zone 3
OFF
Zone 3
ON
Zone 3
OFF
OFF
OFF
Zone 4
Zone 5
ON
OFF
Zone 4
Zone 5
ON
Zone 4
Zone 5
OFF
Zone 6
OFF
Zone 6
ON
Zone 6
Default
UL
See wiring
diagram for
Open Circuit
wiring.
07 Burg (Steady) Output
OFF
02 Exit/Entry Follower Zones
05 40 ms Loop Response Zones
Default
09 Selective Bypass
Default
ON
01 Home/Away with Delay Zones
4
UL
08 Programmable Output (PGM)
Default
OFF
Zone 1
OFF
Zone 1
ON
Zone 1
OFF
Zone 2
OFF
Zone 2
ON
Zone 2
OFF
Zone 3
OFF
Zone 3
ON
Zone 3
OFF
OFF
OFF
Zone 4
Zone 5
ON
OFF
Zone 4
Zone 5
ON
Zone 4
Zone 5
OFF
Zone 6
OFF
Zone 6
ON
Zone 6
ON
Zone 1
ON
Zone 2
ON
Zone 3
ON
ON
Zone 4
Zone 5
ON
Zone 6
17 Wireless Smoke Supervisory Timer
System Times
Smoke Supervisory Timer, hours
10 Exit Delay
Exit Delay, seconds
(0)
(4)
(5)
Maximum Entry 255
(8)
Maximum Entry 8
Entry Delay, seconds
(3)
(0)
Bell Time-out, minutes
(0)
(0)
(5)
Maximum Entry 255
13 Fire (Pulsed) Output Time-out
Bell Time-out, minutes
(0)
(0)
(0)
Maximum Entry 255
14 Test Timer Interval
Test Timer, days
(0)
(0)
(1)
Maximum Entry 255
15 Line Cut Time-to-Fail (Disabled = 000)
16 Wireless Supervisory Timer
Supervisory Timer, hours
(1) (2) Maximum Entry 26
*See Note 4
UL Installations:
hours
Block 16, Wireless Supervisory Timer must be set 10
Maximum Entry 23
Zn 1 LED ON = Audio Verification
OFF
Zn 2 LED ON = *Access Output (A 3)
OFF
Zn 3 LED ON = *Follow Keypad Sounder
OFF
Zn 4 LED ON = *Keyfob/Keyswitch Chirp
*See Note 2
24 Programmable Output (PGM) Features 2
System Features
20 Keypad Features 1
Default
OFF
Zn 1 LED ON = *Keypad Fire (EE )
OFF
Zn 2 LED ON = *Keypad AUX (FF )
ON
Zn 3 LED ON = *Keypad Panic (GG )
Zn 1 LED ON = Audible panic
Zn 2 LED ON = Exit/Entry with Urgency
ON
Zn 3 LED ON = Display Bypass (ARMED)
OFF
Zn 4 LED ON = Disable Code Entry Beeps
22 Miscellaneous Features 1
Default
OFF
Zn 1 LED ON = Abort Delay
ON
Zn 2 LED ON = Easy Arm/Easy Exit
ON
Zn 3 LED ON = Swinger Shutdown
OFF
Zn 4 LED ON = Bell on Line Cut (Armed)
Additional programming required for reporting, see Blocks [36]&[56].
UL Installations: If Keypad Fire [20-1] is enabled, the keypad must be mounted
within (3) three feet from the Control Panel.
Zn 2 LED ON = AUX
OFF
Zn 3 LED ON = Panic
OFF
Zn 4 LED ON = Test Timer
OFF
Zn 1 LED ON = AC Fail
OFF
Zn 2 LED ON = Low Battery
OFF
Zn 3 LED ON = *Trouble
OFF
Zn 4 LED ON = Armed
*See Note 3
Default
OFF
Zn 1 LED ON = Fire
OFF
Default
21 Keypad Features 2
ON
OFF
25 Programmable Output (PGM) Features 3
OFF
Zn 4 LED ON = *Ambush (6th User Code)
*See Note 1
NOTE 1:
NOTE 4:
(2)
OFF
Default
Line Cut Time-to-Fail, seconds
(0) (0) (0) Enable Feature-Valid Entries 10-255
UL
Test Timer Offset, hours
(1)
Maximum Entry 255
12 Burg (Steady) Output Time-out
Default
18 Test Timer Offset
11 Entry Delay
(0)
23 Programmable Output (PGM) Features 1
26 Miscellaneous Features 2
Default
OFF
Zn 1 LED ON = Momentary Keyswitch Arming
OFF
Zn 2 LED ON = Reserved
UL
OFF
Zn 3 LED ON = Inhibit Fail to Communicate
UL
OFF
Zn 4 LED ON = Inhibit Low Battery Display
NOTE 2:
Cannot be programmed with any other Programmable Output (PGM) Feature.
NOTE 3:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure,
Wireless Smoke Low Battery and Wireless Smoke Supervisory Failure.
5
Telephone Number 1 Programming
34 Zone Report, Telco 1
37 System Reporting, Telco 1
Default
30 Subscriber ID Number
31 Telephone Number 1
Default
ON
Zone 1
OFF
Zn 1 LED ON = AC Fail Report (15 min. report delay)
ON
Zone 2
ON
Zn 2 LED ON = Low Battery Report
ON
Zone 3
OFF
Zn 3 LED ON = *Trouble Report
ON
ON
Zone 4
Zone 5
ON
Zn 4 LED ON = Fire Report
*See Note 2
ON
Zone 6
38 System Restore Report, Telco 1
Default
NOTE:
OFF
Zn 1 LED ON = AC Restore Report
A fixed Dial Tone Detection (E) is included prior to the Dialing
Prefix (Block Number 44). Programming an E is not required for
Telco 1, Telco 2 and Telco 3. If dial tone detection is not desired
select No Dial Tone Detection in Communicator Features (Block
Number 46). Program a D if a 4 second delay is required.
OFF
Zn 2 LED ON = Battery Restore Report
OFF
Zn 3 LED ON = Trbl Restore Report
OFF
Zn 4 LED ON = Fire Restore Report
32 Receiver Format
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Disabled
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Point ID
Pager
(4)
33 Receiver Options
Default
OFF
Zone 1
OFF
Zone 2
OFF
Zone 3
OFF
OFF
Zone 4
Zone 5
OFF
Zone 6
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
Zn 2 LED ON = Sumcheck
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = No Handshake
39 Opening Closing Report, Telco 1
Default
OFF
Zn 1 LED ON = User 1 Reporting
OFF
Zn 2 LED ON = User 2 Reporting
OFF
Zn 3 LED ON = User 3 Reporting
OFF
OFF
Zn 4 LED ON = User 4 Reporting
Zn 5 LED ON = User 5 Reporting
OFF
Zn 6 LED ON = User 6 Reporting
36 System Reporting, Telco 1
Default
OFF
Zn 1 LED ON = *KP Fire
OFF
Zn 2 LED ON = *KP AUX (FF)/Ambush
Zn 3 LED ON = *KP Panic (GG)
ON
Default
6
35 Zone Restore Report, Telco 1
(EE)
OFF
Zn 4 LED ON = Test Timer
*See Note 1
NOTE 1:
Requires features to be enabled, see block [20].
NOTE 2:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery, Transmitter Supervisory Faliure,
Wireless Smoke Low Battery, Wireless Smoke Supervisory Failure.
ZONE 3 TX LOW BATTERY
SMOKE 2 LOW BATTERY
“RF TRAN LOW BAT, ZN03”
“RF TRAN LOW BAT, ZN10”
Backup Telephone Programming
Pager Programming
44 Dialing Prefix
40 Subscriber ID Number (Telco 2)
Dialing Prefix for Telco 1, Telco 2
& Telco 3.
47
Leading Digits
(0)
41 Telephone Number 2
(0)
(0)
(0)
45 Communicator Features 1
Default
NOTE:
A fixed Dial Tone Detection (E) is included prior to the Dialing
Prefix (Block Number 44). Programming an E is not required for
Telco 1, Telco 2 and Telco 3. If dial tone detection is not desired
select No Dial Tone Detection in Communicator Features (Block
Number 46). Program a D if a 4 second delay is required.
ON
Zn 1 LED ON = Communicator Enabled
ON
Zn 2 LED ON = DTMF w/ Rotary Back up
OFF
Zn 3 LED ON = DTMF only
OFF
Zn 4 LED ON = Backup to Telco 2
48
46 Communicator Features 2
42 Receiver Format
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Point ID
Pager
Trailing Digits
Default
(4)
43 Receiver Options
OFF
Zn 1 LED ON = No Dial Tone Detection
OFF
Zn 2 LED ON = 2:1 Rotary Dialing
OFF
Zn 3 LED ON = Backup if < 4 attempts
OFF
Zn 4 LED ON = Reserved
*(C) *See Note 1
49 Pager Option
Default
OFF
Zn 1 LED ON = Skip Alarm Data
OFF
Zn 2 LED ON = Reserved
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
Default
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
Zn 2 LED ON = Sumcheck
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = No Handshake
NOTE 1:
C = TouchTone #. This is the typical terminating digit for
most paging systems. Recommended, but may not be
required by paging system. D = 2 second delay.
7
Telephone Number 3 Programming
54 Zone Report, Telco 3
50 Subscriber ID Number
57 System Reporting, Telco 3
Default
31 Telephone Number 3
Default
OFF
Zone 1
OFF
OFF
Zone 2
Zn 1 LED ON = AC Fail Report (15 min. report delay)
OFF
OFF
Zone 3
Zn 2 LED ON = Low Battery Report
OFF
OFF
Zn 3 LED ON = *Trouble Report
OFF
Zone 4
Zone 5
OFF
Zn 4 LED ON = Fire Report
*See Note 2
OFF
Zone 6
58 System Restore Report, Telco 3
Default
NOTE:
A fixed Dial Tone Detection (E) is included prior to the Dialing Prefix
(Block Number 44). Programming an E is not required for Telco 1,
Telco 2 and Telco 3. If dial tone detection is not desired select No Dial
Tone Detection in Communicator Features (Block Number 46).
Program a D if a 4 second delay is required.
55 Zone Restore Report, Telco 3
Default
52 Receiver Format
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Disabled
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Point ID
Pager
(4)
Default
Zn 1 LED ON = AC Restore Report
OFF
Zn 2 LED ON = Battery Restore Report
OFF
Zn 3 LED ON = Trbl Restore Report
OFF
Zn 4 LED ON = Fire Restore Report
OFF
Zone 1
OFF
Zone 2
OFF
Zone 3
Default
OFF
OFF
Zn 1 LED ON = User 1 Reporting
OFF
Zone 4
Zone 5
OFF
Zn 2 LED ON = User 2 Reporting
OFF
Zone 6
OFF
Zn 3 LED ON = User 3 Reporting
OFF
OFF
Zn 4 LED ON = User 4 Reporting
Zn 5 LED ON = User 5 Reporting
OFF
Zn 6 LED ON = User 6 Reporting
59 Opening Closing Report, Telco 3
56 System Reporting, Telco 3
Default
53 Receiver Options
OFF
OFF
Zn 1 LED ON = *KP Fire
OFF
Zn 2 LED ON = *KP AUX (FF)/Ambush
Zn 3 LED ON = *KP Panic (GG)
(EE)
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
OFF
Zn 2 LED ON = Sumcheck
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = Test Timer
*See Note 1
OFF
Zn 4 LED ON = No Handshake
NOTE 1:
Requires features to be enabled, see block [20].
NOTE 2:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver
Tamper, Receiver JAM, Transmitter Low Battery, Transmitter Supervisory
Faliure, Wireless Smoke Low Battery, Wireless Smoke Supervisory
Failure.
ZONE 3 TX LOW BATTERY
SMOKE 2 LOW BATTERY
8
“RF TRAN LOW BAT, ZN03”
“RF TRAN LOW BAT, ZN10”
Report Codes
62 Zone Codes
60 Zone Report Codes
Zone 1 Alarm Code
(3)
Zone 2 Alarm Code
(3)
Zone 3 Alarm Code
(3)
Zone 1, 2, 3, 4, 5 & 6 Restore Code
NOTE:
The second digit of the
Report Code is the
number of the zone that
is reporting.
For
example zone 5 report
code (default of 3)
would be 35.
(E)
Zone 1, 2, 3, 4, 5 & 6 Trouble Code
(F)
Zone 4 Alarm Code
(B) Opening Code
63 System Report Codes
(1)
(1)
Keypad AUX (FF)
Zone 5 Alarm Code
(3)
(3)
(2)
(3)
(2)
(1)
(F)
(F)
(F)
(9)
Test Timer
AC Fail
(F)
61 Point ID Report Codes
(3)
Zone 4 Alarm Code
(3)
Zone 5 Alarm Code
(3)
Zone 6 Alarm Code
(3)
(8)
*Trouble
Zone 1 Alarm Code
Zone 3 Alarm Code
(2)
(2)
(F)
1
2
3
4
5
6
7
8
9
A
B
FIRE
PANIC
BURGLARY
HOLDUP
GENERAL ALARM
RESERVED
GAS ALARM
HEAT ALARM
RESERVED
AUXILIARY
24 HOUR ALARM
Enhanced Communicator Features
67 Telephone Number 1
Default
Low Battery
Zone 2 Alarm Code
66 Ambush Report Code
Keypad Panic (GG)
Zone 6 Alarm Code
(3)
(C) Closing Code
Keypad Fire (EE)
(3)
(3)
65 Opening and Closing Code
(1)
OFF
Zn 1 LED ON = Opening after Alarm (Cancel Code)
OFF
Zn 2 LED ON = Conditional Closing
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
Fire
(1)
(1)
*See Note 1
64 System Restore Code
(E)
68 Telephone Number 3
Default
OFF
Zn 1 LED ON = Opening after Alarm (Cancel Code)
OFF
Zn 2 LED ON = Conditional Closing
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
NOTE 1:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver
Tamper, Receiver JAM, Transmitter Low Battery, Transmitter
Supervisory Faliure, Wireless Smoke Low Battery and Wireless
Smoke Supervisory Failure.
9
Wireless
Transmitters
RF ID #
71 Zone 1
:
72 Zone 2
:
73 Zone 3
:
74 Zone 4
:
75 Zone 5
:
76 Zone 6
:
Keyfobs
RF ID #
81 Keyfob 1
82 Keyfob 2
83 Keyfob 3
84 Keyfob 4
Programming Example
Point
Enter the RF ID# located on
the Transmitter, Key Fob and
Smoke Detector labels.
Enter the point number to be
associated with the zone. If only
one point of GEM-TRANS2 is
used, enter a 1 in this location.
For GEM-GB, GEM-DT, GEMPIR enter a 1 in this location.
AUX 1 & 2
Programming
1
2
3
4
5
6
7
8
:
:
:
Panic
AUX
Bell ON
PGM
Instant
Access on PGM
Full Set System
Interior
:
73 Zone 3
0
0
1
2
B
10
A= A 1
B= A 2
C= A 3
:0
3.Enter
0012A200
4.Enter
1
1
(beeps)
Hexadecimal B Entry
Note: If the RF ID# in step 3 is not entered correctly the
keypad will emit a 1 second tone indicating incorrect entry.
Repeat steps 2 - 4 above.
Smoke Detectors
RF ID #
85 Smoke 1
:
86 Smoke 2
:
87 Smoke 3
:
88 Smoke 4
:
Hexadecimal Data Entry
To Enter a hexadecimal digit enter the following:
0
1.Enter Dealer Mode.
2.Enter B (beeps) 7 3 (beeps)
RF ID # XXXXXX:X
AUX 1 AUX 2
Map point 1 of a window door transmitter, with RF ID# 0012B0:0
to Zone 3.
D= A 4
E= A 5
F= A 6
Downloading
90 Callback Telephone Number
Dealer Programming
94 Dealer Code
(4) (5) (6) (7)
91 Ring Count
95 User 1 Code
97 Dealer Options 2
Default
OFF
Zn 1 LED ON = *International Dialing Protocol
OFF
Zn 2 LED ON = *Invert Bell Output
OFF
Zn 3 LED ON = System Trouble Auto Restore
OFF
Zn 4 LED ON = User 1 Code-Program only
*See Note 1
(0) (9) Maximum Entry 15
(1) (2) (3) (4)
92 Downloading Features
Default
ON
Zn 1 LED ON = Ring Method
ON
Zn 2 LED ON = Answering Machine override
ON
Zn 3 LED ON = Command 6(A6) Download
OFF
Zn 4 LED ON = Signal Strength Test Mode
98 Number of Re-Dials
96 Dealer Options 1
Default
OFF
Zn 1 LED ON = Dealer Code Lockout
ON
Zn 2 LED ON = User 1 Code Lockout
OFF
Zn 3 LED ON = UL Household Fire
OFF
Zn 4 LED ON = Fire Trouble on Fire LED
(9)
NOTE 1:
International Features
93 Auto Download ID Number
11
XP-600 WIRING DIAGRAM
E1
+ RED
RECHARGEABLE
BATTERY
12 VDC 4AH OR 7AH
E2
This equipment should be installed in accordance with Chapter
2 of the National Fire Alarm Code, ANSI/NFPA 72-1996
(National Fire Protection Association Batterymarch Park,
Quincy MA 02269). and local codes. Information describing
proper installation, operation, testing, maintenance, evacuation
planning, and repair service is to be provided with this
equipment. UL Listed Energy Cable is required.
(REFER TO PROGRAMMING INSTRUCTIONS WI1373)
RESIDENTIAL BURG (4 HOUR STANDBY)
COMBINED STANDBY = 500 mA
BELL = 2.0 AMP
BLACK
RESIDENTIAL FIRE (24 HOUR STANDBY) (3)
COMBINED STANDBY = 120 mA
BELL = 95 mA
RECOMMENDED BATTERIES YUASA
NP4-12 AND NP7-12
REPLACE EVERY FIVE YEARS
DS1
TELE LINE IN USE
ALL OUTPUTS ARE CURRENT LIMITED
COLD WATER GROUND CONNECTION
USE ONLY COLD-WATER PIPE OR
BURIED GROUND ROD. USE AT LEAST
#16 AWG WIRE.
1
2.2K
(E)
+10 -11 +12 -13
BELL
GND
+PWR
ZONE 5
2.2K
2.2K
2.2K
(E)
ZONE 6
(E)
(E)
2.2K
2.2K EOLR
ZONE 1
ZONE 3
ZONE 2
(E)
2.2K
2.2K EOLR
(SUPERVISED)
18
19
RING
TIP
RING
TELCO
RPXP6GT
(+)
PHONE
To RJ31X
(Supervised)
WARNING
TO PREVENT RISK
OF ELECTRIC SHOCK
DISCONNECT TELEPHONE
LINES PRIOR TO
SERVICING
GEM-RECV-XP8
12
+PWR
(E)
Normally Open
Zone Wiring
FT2200
3.9K
2.2K
Wire the normally open
contact as shown
(Zone 4). Program
the zone for
Open Circuit [06]
operation.
(Z)
ZONE 4
(E)
ZONE 1
4-Wire Fire Wiring
RED
BLACK
BROWN
BROWN
XP-600 Terminals
Power
Out (+)
Power
Out (-)
Power
In (+)
Power
In (-)
Fire Loop Fire Loop
Out
In
BRN
ZONE 4
17
TIP
GRAY
+
16
(-)
GRN
(Z)
15
PGM
Programmable
Output
+
BLK
(1)
14
GND GREEN
REMOTE BUS
+
(1) ALL ZONE RESISTORS MUST BE INSTALLED, EVEN IF
ZONE IS NOT USED.
(2) COMBINED STANDBY = KEYPAD CURRENT + AUX POWER
CURRENT + FIRE POWER + PGM CURRENT.
(3) RESIDENTIAL FIRE REQUIRES A 7AH BATTERY.
(4) UNIT INTENDED TO BE MOUNTED VERTICALLY ON WALL.
(5) REFER TO WI1372 FOR COMPATIBLE TWO WIRE SMOKE
DETECTORS. DO NOT MIX DIFFERENT MODELS.
(6) THIS PANEL SHALL BE CHECKED BY A QUALIFIED
TECHNICIAN AT LEAST ONCE EVERY THREE YEARS.
(7) THIS PANEL SUPPORTS ONLY ONE SMOKE DETECTOR IN
ALARM.
(8) USE ONLY ONE BELL IN RESIDENTIAL FIRE APPLICATION.
(9) SYSTEM MUST BE TESTED AT LEAST ONCE A WEEK IN THE
AC/BATTERY MODE AND IN THE BATTERY-ONLY MODE.
(CONTACT CENTRAL STATION PRIOR TO TESTING) AC MUST
BE RESTORED AFTER TEST.
12
FIRE
GRN
(Z)
GOLD
WHITE RED
-9
+
(Z)
3.9K
ORANGE
+8
+
3.9K
EARTH
GROUND
-7
FIRE
PWR
3.9K
3.9K
(Z)
+6
LOAD
50 mA MAX.
GOLD
RED RED
+5
RED
RED
-4
AUX POWER OUTPUT 10-12.5 VDC
Zone
DoublingTM
Resistors
+3
RED
EZ
2
16 VAC 20 VA
TRANSFORMER
NAPCO TRF12
(OR EQUIVALENT
SEE WI1372).
Class 2
Transformer.
DO NOT
connect to
switched
outlet.
8 Fire Power
7 Ground
8 Fire Power
9 Fire
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement