Bacharach Model 200 Operating instructions

Add to my manuals
45 Pages

advertisement

Bacharach Model 200 Operating instructions | Manualzz

TM 9-4910-409-12

D E P A R T M E N T O F T H E A R M Y T E C H N I C A L M A N U A L

O P E R A T O R A N D O R G A N I Z A T I O N A L

M A I N T E N A N C E M A N U A L

( I N C L U D I N G R E P A I R P A R T S

A N D S P E C I A L T O O L L I S T S )

T E S T E R D I E S E L F U E L I N J E C T O R

N O Z Z L E ( B A C H A R A C H I N D U S -

T R I A L I N S T R U M E N T C O M P A N Y

M O D E L Y F L ) ( 4 9 1 0 - 2 5 5 - 8 6 4 1 ) W I T H

C O N N E C T O R S E T 4 4 ( B A C H A R A C H

P A R T N U M B E R 6 5 - 2 7 5 ) ( 4 9 1 0 - 9 5 5 - 5 5 1 7 )

A N D C O N N E C T O R S E T ( O R D D W G

B 1 1 0 2 0 4 9 8 ) ( 4 9 1 0 - 9 5 5 - 5 5 1 6 )

HEADQUARTERS, DEPARTMENT OF THE ARMY

O C T O B E R 1 9 6 3

Changes in force: C1

Change

No. 1

TM 9-4910-409-12

C 1

HEADQUARTERS

DEPARTMENT OF THE ARMY

Washington, D.C., 25 June 1973

Operator and Organizational Maintenance Manual

(Including Repair Parts and Special Tool Lists)

TESTER, DIESEL FUEL INJECTOR NOZZLE

(BACHARACH INDUSTRIAL INSTRUMENT COMPANY

MODEL YFL) (4910-255-8641)

WITH CONNECTOR SET 44 (BACHARACH

PART NUMBER 65-275) (4910-955-5517)

AND CONNECTOR SET (ORD DWG B11020498)

(4910-955-5516)

TM 9-4910-409-12, 29 October 1963, is changed as follows

Page 2. paragraph 1f is superseded as follows

1f. You can improve this manual by calling attention to errors and by recommending improvements using DA Form 2028 (Recommended

Changes to Publications) or by a letter and mailing direct to Commander, US Army Weapons Command, ATTN: AMSWE-MAS-SP, Rock

Island IL 61201. A reply will be furnished direct to you.

Page 3. Add the following to paragraph 4:

Parts included with the end item and considered a s c o m p o n e n t s o f t h e e n d i t e m c o n f i g u r a t i o n are listed in the following table:

Table 0. Components of the End Item

Components

Part No.

(FSCM) Qty

CASE, CARRYING: 65-808 (05083) 1

CONNECTOR SET, FUEL INJECTOR 11020498 (05083) 1

CUP, COLLECTOR

HOSE, PRESSURE, HIGH

65-317 (05083) 1

65-284 (05083) 1

Page 22. Appendix II is superseded as follows:

APPENDIX II

BASIC ISSUE ITEMS LIST

AND

ITEMS TROOP INSTALLED OR AUTHORIZED LIST

The basic issue items and items troop installed or authorized lists are not applicable.

1

By Order of the Secretary of the Army:

Official:

VERNE L. BOWERS

Major General, United States Army

The Adjutant General

CREIGHTON W. ABRAMS

General, United States Army

Chief of Staff

Distribution:

Active Army:

DCSLOG (3)

CNGB (1)

TSG(l)

COE (5)

CONARC (2)

AMC (5)

ARADCOM (2)

ARADCOM Rgn (2)

Armies (3) except

7th USA (5)

8th USA (5)

Corps (2)

OS Maj Comd (2)

LOGCOMD (2)

WECOM (10)

Ft Belvoir (2)

A P G ( l )

NG: State AG (3)

USAR: None

For explanation of abbreviations used, see AR 310-50.

LEAD (2)

LEAD (2)

Instl (2) except

Ft Monmouth (5)

Dir of Trans (1)

USACOMZEUR(l)

Arsenals (1) except

Detroit Arsenal (5)

Units org under fol TOE:

(2 cys each)

7-37

10-500(H-K)

17

29-51

29-56

57

* U . S . G O V E R N M E N T P R I N T I N G O F F I C E 1 9 7 3 - 7 6 9 6 2 0 / 9 9 1

2

TM 9-4910-409-12

Technical Manual

No. 9-4910-409-12

HEADQUARTERS,

DEPARTMENT OF THE ARMY

WASHINGTON 25, D. C., 29 October 1963

OPERATOR AND ORGANIZATIONAL MAINTENANCE MANUAL

(INCLUDING REPAIR PARTS AND SPECIAL TOOL LISTS)

TESTER, DIESEL FUEL INJECTOR NOZZLE

(BACHARACH INDUSTRIAL INSTRUMENT COMPANY

MODEL YFL) (4910-255-8641) WITH CONNECTOR SET 44

(BACHARACH PART NUMBER 65-275) (4910-955-5517)

AND CONNECTOR SET (ORD DWG B11020498)(4910-955-5516)

Paragraph Page

C H A P T E R

1 .

Section I.

C

H A P T E R

Section

II.

2.

I.

II.

C

H A P T E R

Section

III.

3.

I.

II.

111.

C

C

H A P T E R

Section

H A P T E R

IV.

4.

I.

II.

III.

IV.

V.

VI.

5.

Section I.

II.

APPENDIX I.

II.

III.

IV.

INDEX ..,...

INTRODUCTION

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description and data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATING INSTRUCTIONS

Service on receipt of materiel. . . . . . . . . . . . . . . . . . . . . . . . . . .

Controls, instruments, and related items . . . . . . . . . . . . . . . . . . . .

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3

4-6

2

3

7,8 5

9-13 5,6

14-16 6

OPERATOR MAINTENANCE INSTRUCTIONS

Repair parts, tools, and equipment . . . . . . . . . . . . . . . . . . . . . . . .

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preventive-maintenance services . . . . . . . , . . . . . . . . . . . . . . . . .

Troubles hooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ORGANIZATIONAL MAINTENANCE INSTRUCTIONS

Repair parts, tools, and equipment . . . . . . . . . . . . . . . . . . . . . . . .

Painting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preventive-maintenance services . . . , . . . . . . . . . . . . . . . . . . . . .

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel reservoir assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Discharge block assembly and hydraulic pressure gage . . . . . . . . . . .

SHIPMENT AND ADMINISTRATIVE STORAGE AND DEMOLITION

TO PREVENT ENEMY USE

17-20 9

21 9

22-24 9,10

25-27 11,12

28-31

32

33,34

38,39

40,41

13

13

13

35-37 13,14

14

16

Shipment and administrative storage . . , . . . . . . . . . . . . . . . . . . . .

Demolition of materiel to prevent enemy use . . . . . . . . . . , . . . . . .

42-44 17

45,46 18,19

REFERENCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

BASIC ISSUE ITEMS, REPAIR PARTS, AND TOOL LISTS . . . . . . . . . . . . . .

MAINTENANCE ALLOCATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . .

REPAIR PARTS AND SPECIAL TOOL LISTS . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20

22

27

28

35

1

CHAPTER 1

INTRODUCTION

1. Scope

Section I.

G E N E R A L

(e. g. officer, noncommissioned supervisor, etc.).

officer,

a. This technical manual contains instructions on operation and maintenance of the diesel fuel injector nozzle tester for the operator and instructions for organizational maintenance of the nozzle tester by personnel of the using organization.

b. Appendix I contains a list of current

references, including supply manuals, forms, technical manuals, and other available publications applicable to the nozzle tester.

c. Appendix II contains a list of equip-

ment and tools which are required by the operator for operating and maintaining the nozzle tester.

d. Appendix III contains the maintenance

allocation chart for the nozzle tester listing all maintenance and repair operations authorized for all maintenance echelons.

e. Appendix IV contains a list of repair

parts which are required by the using organization for performing organizational maintenance on the nozzle tester.

f. The direct reporting of errors, omissions and recommendations for improving this equipment manual by the individual user, is authorized and encouraged. DA

Form 2028 will be used for reporting these improvements. This form may be completed using pencil, pen or typewriter.

DA Form 2028 will be completed in triplicate and forwarded by the individual using the manual. The original and one copy will be forwarded direct to:

Commanding General

Headquarters, U. S. Army Weapons

Command

ATTN: AMSWE-SMM-TE

Rock Island Arsenal

Rock Island, Illinois 61202

One information copy will be provided to the individual’s i m me d i a t e supervisor

2

2. Maintenance Allocation

a. Operator Maintenance Allocation. The prescribed maintenance to be performed by the operator will apply as reflected in the operator-maintenance (first echelon) column of the maintenance allocation chart

(app. III). In all cases, where the nature of

the repair, modification, or adjustment is beyond the scope or facilities of the operator, organizational-maintenance personnel should be informed so that trained personnel with suitable tools and equipment may be provided or other instructions issued.

b. Organizational Maintenance Allocation.

The prescribed maintenance to be performed by maintenance personnel of the using organization will apply as reflected in the organizational-maintenance (second echelon) column of the maintenance allo-

cation chart (app. III). In all cases where

the nature of the repair, modification, or adjustment is beyond the scope or facilities of the using organization, the supporting maintenance unit should be informed so that trained personnel with suitable tools and equipment may be provided or other instructions issued.

3. Farms, Records, and Reports

a. General. Responsibility for the proper execution of forms, records, and reports rests upon the officers of all units maintaining this equipment. However, the value of accurate records must be fully appreciated by all persons responsible for their compilation, maintenance, and use,

Records, reports, and authorized forms are normally utilized to indicate the type, quantity, and condition of materiel to be

inspected, to be repaired, or to be used in repair. Properly executed forms convey authorization and serve as records for repair or replacement of materiel in the hands of troops and for delivery of materiel requiring further repair to shops in arsenals, depots, etc. The forms, records, and reports establish the work required, the progress of the work within the shops, and the status of the materiel upon completion of its repair.

b. Authorized Forms. The forms generally applicable to units operating or maintaining this materiel are listed in

appendix I. For a listing of all forms, refer

to DA Pam 310-2. For instructions on use of these forms, refer to FM 9-3 and TM

38-750.

c. Equipment Improvement Recommendations.

Any deficiencies detected in the equipment covered herein which occur under the circumstances indicated in AR

750-5, should be immediately reported in accordance with the applicable instructions in cited regulation.

d. Field Report of Accidents. The report necessary to comply with the requirements of the Army safety program are prescribed in detail in AR 385-40. These reports are referenced whenever accidents involving injury to personnel or damage to materiel occur.

Section Il. DESCRIPTION AND DATA

4. Description

The nozzle tester (fig. 1) is an instru-

ment used for analyzing and testing the accuracy of diesel engine injector nozzles for opening pressure, spray p a t t e r n, chatter, and leakage. It consists of a hydraulic pressure gage, fuel reservoir assembly, discharge block assembly, and body and plunger assembly. The fluid used for testing nozzles is contained in the fuel reservoir assembly. The flow of the fluid is maintained by the pressure developed through the action of the body and plunger assembly and is controlled by the discharge block assembly, The pressure developed during the various tests is indicated on the hydraulic pressure gage. The nozzle tester is contained in a metal carrying case with all necessary accessories, equipment, and instruction handbook.

5. Data Plate

The nozzle tester has one data plate (3A,

fig. 1) which is located on the discharge block assembly (3, fig, 1). This plate spec-

ifies the manufacturer’s name, address, and code number.

6. Tabulated Data

Manufacturer . . . . .

Model . . . . . . . . . .

Length . . . . . . . . . .

Width . . . . . . . . . .

Height . . . . . . . . . .

Bacharach Industrial Instrument

Company

YFL

12 in.

10 in.

7-1/2 in.

Cubage (w/equipment) packaged . . . . . . . .999 tuft

Weight (w/equipment) packaged . . . . . . .24lb

3

l–Fuel reservoir assembly

A–Fuel reservoir

B–Center rod assembly

C–Fuel reservoir cover

2–Hydraulic pressure gage

3–Discharge block assembly

A–Data plate

B–Valve handle

C–Hydraulic pressure gage valve assembly

D–Upper discharge outlet

E–Lower discharge outlet

F–Cap nut assembly

4–Body and plunger assembly

A–Handle shoe

B–Pump handle assembly

C–Vent screw

Figure 1. Nozzle tester.

CHAPTER 2

OPERATING INSTRUCTIONS

7. Purpose

Section I. SERVICE UPON RECEIPT OF MATERIEL

a. When a new or reconditioned nozzle tester is first received, it is the responsibility of the officer in charge to determine whether the materiel has been properly prepared for service by the supplying organization and to be sure it is in condition to perform its function. For this purpose, inspect all assemblies and parts to be sure they are properly assembled, secured, cleaned, adjusted, and/or lubricated.

b. Make a record of any missing parts, tools, and/or equipment, and any malfunctions. Correct any deficiencies as quickly as possible.

8. Services

a. Unpacking and Checking. Pry off the top of the exterior container and turn the container upside down letting the nozzle tester slide out of the container, Remove the barrier material enveloping the nozzle tester and all cushioning materials, seals, and wrappings from the case of the nozzle tester, also, all equipment stored in the case. Check all equipment with the listing

in appendix II to be sure every item is

present and in good condition.

b. Cleaning. Remove all preserving materials and clean all parts of the nozzle tester, and equipment as prescribed in

paragraph 23.

c. Lubrication. The nozzle tester requires no lubrication.

d. Inspection.

(1)

(2)

(3)

Perform a general inspection of the nozzle tester to assure that all parts are properly and securely assembled and in good condition

(par. 22 b).

Perform the preventive-maintenance services as prescribed in

table I, paragraph 24.

Operate the nozzle tester (pars.

15 and 16) and check to see if the

components are functioning properly by checking such items as hydraulic pressure gage, body and plunger assembly, etc.

Section Il. CONTROLS, INSTRUMENTS, AND RELATED ITEMS

Note: The key numbers shown below in parentheses in this section refer to figure 1 except

wise indicated.

where other-

9. General

This section describes, illustrates, and furnishes the operator with sufficient information pertaining to the various controls, instruments, and related items for the proper operation of the nozzle tester.

10. Fuel Reservoir Assembly

The fuel reservoir (1A) contains the test fluid used to conduct tests when checking the performance of

- The fuel reservoir fuel injector nozzles; has a built in paper

type filter element (2D, fig. 3). The test

fluid is forced through the filter element by atmospheric pressure and pump suction.

11. Hydraulic Pressure Gage Valve

Assembly

The hydraulic pressure gage valve assembly (3C) stops the flow of the test fluid to the hydraulic pressure gage. Turn the valve handle (3B) left to open and right to close.

5

12. Hydraulic Pressure Gage

The hydraulic pressure gage (2) indicates the amount of pressure applied when testing the various types of nozzles.

The dial has a range of O to 5,000 psi

(pounds per square inch) and marked in increments of 50 psi.

13. Pump Handle Assembly and Handle Shoe

The action of the pump handle assembly

(4B) and handle shoe (4A) actuates the plunger built within the body and plunger assembly (4), and producing a hydraulic pressure which is recorded on the hydraulic pressure gage (2).

Section Ill. OPERATION

Note:

The key numbers shown below in parentheses in this section refer to figure 1.

14. General

This section contains instructions for the operation of the nozzle tester under conditions of moderate temperatures and humidity. Every organization equipped with this item must thoroughly train its personnel in the procedures for operating this item.

15. Preparation for Operation

a. Mount the nozzle tester (fig. 1) on a

bench and secure with three 3/8-inch bolts, washers, and nuts. For portable use, mount on wooden or metal base 5 inches wide x

15 inches long. Use 3/4-inch plywood or l/2-inch sheet steel.

b. Slide the pump handle assembly (4B) onto the handle shoe (4A) located in the base of the nozzle tester. Solid shaft in the pump handle assembly may be extended or telescoped, depending on 1 e v e r a g e required.

c. Remove the fuel reservoir cover (lC) from the fuel reservoir (1A) with a combined twisting and pulling motion. Fill the fuel reservoir with test fluid and install the fuel reservoir cover.

d. Open the valve handle (3B) and make several strokes with the pump handle assembly (4B) to prime the nozzle tester.

Close the valve handle.

N o t e . A vent screw (4C) is located on the side of the housing behind the lower discharge outlet (3E) and can be opened for thorough venting and priming i f n e c e s s a r y .

6

16. Operation

a. Discharge Block Assembly. The discharge block assembly (3) has two discharge outlets to facilitate the various tests. When nozzle under test is connected to lower discharge outlet (3E) and with hydraulic pressure gage valve assembly

(3C) closed, this shuts off and protects the hydraulic pressure gage (2) during rapid and prolonged pumping periods when flushing nozzle or observing spray form. Using upper discharge outlet (3D) and closing hydraulic pressure gage valve assembly

(3C) isolates hydraulic pressure gage (2) and the nozzle under test from the nozzle

tester (fig. 1) permitting leakage rates or

pressure drop measurement tests.

Note. Install and tighten cap nut assembly (3F) on discharge outlet not in use.

b. Mounting Instructions. Mount the fuel injector nozzle to be tested on the nozzle tester in accordance with the connecting

instructions (fig. 2) using connector set

4910-955-5517 (1, fig. 6).

N o t e .

C o n n e c t o r s e t 4 9 1 0 - 9 5 5 - 5 5 1 6 ( 2 , f i g . 6 ) i s

c o n n e c t e d i n a s i m i l a r m a n n e r a s c o n n e c t o r s e t

4910-955-5517 (1, fig. 6).

c. Testing Nozzles.

(1) General. For the v a r i o us tests, connect the nozzle to the discharge outlets, as prescribed in (2), (3),

(4) and (5) below. Use the spray

collector cup (2, fig. 5) for catch-

ing the test fluid. For best results, tip of nozzle should be well centered in the cup.

Warning: Be careful of the penetrating power of the atomized test fluid under pressure as it is sufficient to puncture the skin permit-

ting test fluid to enter wound and

INSTRUCTIONS

CONNECTOR SET 44

B A C H A R A C H P A R T N O . 6 5 - 2 7 5

Figure 2. Connecting instructions.

7

8

(2)

(3) may cause blood poisoning. Keep hands free of spray at all times.

Opening Pressure. Use lower discharge outlet (3E). Open the hydraulic pressure gage valve assembly (3C), operate the pump handle assembly (4B) slowly and, when nozzle begins to spray test fluid, observe the pressure indicated on the hydraulic pressure gage (2). This pressure should be compared with that specified by the engine manufacturer and nozzle adjusted, if necessary, before proceeding with further testing. Test should be repeated several times to be certain that nozzle consistently opens at the same pressure each time.

Spray Pattern.

Use lower discharge outlet (3E). Close the hydraulic pressure gage valve assembly (3C) and operate the pump handle assembly (4B) at approximately 15 strokes per minute.

Make sure that all spray holes are open and are spraying the same amount of test fluid. The spray formation should be sharp with a rather solid pattern and the angles formed by the individual sprays should be uniform. A missing section or uneven spray pattern indicates clogged or eroded orifices.

(4)

(5)

Sample spray patterns are generally shown in the engine manual.

Chatter. Use lower discharge outlet (3E). Close the hydraulic pressure gage valve assembly (3C) and operate the pump handle assembly

(4B) approximately two seconds.

The nozzle chatter must be distinct and regular. A sharp pitch sound is not mandatory, and an occasional skip or variation in the chatter sound pitch is acceptable.

When nozzle chatter is not satisfactory and does not improve with continued operation of the pump handle assembly, replace the nozzle.

Leakage. Use lower discharge outlet (3E). Open the hydraulic pressure gage valve assembly (3C) and opera t e pump handle assembly

(4B). During prolonged pumping, drops of test fluid should not form at tip of the nozzle. A second check for leakage can be made by maintaining pressure just below opening pressure and checking for test fluid leakage from tip. If this test is to be used, reconnect nozzle to upper discharge outlet (3D) and close the hydraulic pressure gage valve assembly (3C) to time pressure drop.

Some manufacturers specify permissible leakage rates.

CHAPTER 3

OPERATOR MAINTENANCE INSTRUCTIONS

17. General

Repair parts, tools, and equipment are issued to the operator for operating and maintaining the nozzle tester. Tools and equipment should not be used for

Purposes other than prescribed and when not in use should be properly stored.

18. Repair Parts

No repair parts are supplied to the operator for replacement of those already on the nozzle tester.

Section I. REPAIR PARTS, TOOLS, AND EQUIPMENT

19. Common Tools and Equipment

Common tools and equipment having general application to this materiel are authorized by tables of allowances and tables of organization and equipment.

20. Special Tools and Equipment

No tools specially designed for operation or operator maintenance are supplied or required for the nozzle tester. Equipment

supplied is listed in appendix II, which is

the authority for requisitioning replacement.

Section Il. LUBRICATION

21. Lubrication

No lubrication is required on the nozzle tester.

Section Ill. PREVENTIVE-MAINTENANCE SERVICES

22. General

a. Responsibility and Intervals.

T h e primary function of preventive maintenance is to prevent breakdown and, therefore, the need for repair. These services consist generally of before operation and after-operation services performed by the operator. Intervals are based on normal operations, Reduce intervals for abnormal operations or severe conditions.

Intervals during inactive periods may be extended accordingly.

b. Definition of Terms. The general inspection of each item applies also to any supporting member or connection and is generally a check to see whether the item is in good condition, correctly assembled, secure and not excessively worn:

(1) The inspection for “good condition”

(2)

(3) is usually an external visual inspection to determine whether the unit is damaged beyond serviceable limits by the following not bent or twisted, not chafed or burred, not broken or cracked, n o t bare or frayed, not dented or colIapsed, not torn or cut, not deteriorated.

The inspection of a unit to see that it is “correctly assembled” is usually an external visual inspection to see whether it is in its normal assembled position.

Inspection of a unit to determine if it is “secure” is usually an external visual examination or an examination by hand or wrench for looseness. Such an examination must include any brackets, lockwashers,

9

(4) lock nuts, locking wires, or cotter pins used.

By “excessively worn” is me ant worn beyond serviceable limits or to a point likely to result in failure if the unit is not replaced before the next scheduled inspection.

23. Cleaning

a.. General. Any special cleaning instructions required for specific components or parts are contained in the pertinent section. Cleaning instructions are as outlined in (1) and (2) below. General cleaning precautions are contained in b below.

(1) Metal parts.

(a)

(b)

Use self-emulsifying decreasing solvent compound, mineral spirits paint thinner, or dry-cleaning solvent (Stoddard) to clean or wash grease or oil from all metal parts of the nozzle tester.

Use clean water or a solution of either 1/4 pound of soap chips or six ounces of painted-surface detergent to one gallon of hot water for all parts and overall general

(c) cleaning of painted surfaces.

After parts are clean, dry them thoroughly. Apply a light film of special preservative lubricating oil to all parts having a polished surface to prevent misting.

Before installing new parts, re(d) move any rust-preventive compound, protective grease, etc.

(2) Rubber Parts Other Than Electrical. Clean rubber parts with soap and warm water. Apply a coating of powdered technical talcum to preserve the rubber.

b. General Precautions in Cleaning.

(1) Self-emulsifying decreasing solvent compound, mineral spirits paint thinner, and dry-cleaning solvent are flammable and should not be used near an open flame.

Fire extinguishers should be provided when these materials are used Use only in well-ventilated places. These cleaners evaporate

(2) quickly and have a drying effect on the skin. If used without gloves, they may cause cracks in the skin and, in the case of some individuals, a mild irritation or inflammation.

Avoid getting petroleum products, such as mineral spirits paint thinner, dry-cleaning solvent, engine fuels, or lubricants, on rubber parts, as they will deterior-

(3) ate the rubber.

The use of Diesel fuel oil, gasoline, or benzene (benzol) for cleaning is prohibited.

c. Rust Removal.

Remove rust or corrosion from all parts of the materiel.

To remove rust or corrosion from unfinished surf aces, use steel cleaning brushes or abrasive cloth. On finished surfaces, other than highly polished surfaces, remove rust or corrosion by buffing with a rotary wheel wire brush constructed of steel wire between 0.010

and 0.025 inch in diameter. Crocus cloth may be used manually to remove rust or corrosion from polished surfaces.

24. Operator’s Preventive-Maintenance

Services

a. Purpose. To insure efficient operation, it is necessary that the nozzle tester be systematically inspected at intervals each day it is operated so defects may be discovered and corrected before they result in serious damage or failure. Certain scheduled maintenance services will be performed at these designated intervals. The correction of any defect or unsatisfactory operating characteristics beyond the scope of the operator must be reported at the earliest opportunity to organizational mainte-

nance personnel for correction (pars. 33

through 41).

b. Services. Operator’s preventivemaintenance services are listed in table I. Every operator equipped with the nozzle tester must be thoroughly familiar with maintenance procedures for this materiel.

10

Table I.

Preventive Maintenance Checks and Services

1st Echelon Daily Schedule

Table I. Preventive Maintenance Checks and Services — Continued

1st Echelon Daily Schedule

Item to be inspected

Procedure Paragraph reference

Item to be inspected

Procedure Paragraph reference

Nozzle tester & Clean hydraulic pressure gage by wiping dirt and other foreign matter from ridges and surface of gage face.

b. Clean accumulation of dirt and other foreign matter from outside surface of the fuel reservoir assembly.

c. Clean the accumulation of dirt and other foreign matter from interior surfaces of the body and plunger assembly at point of handle entrance in handle shoe.

Inspect painted surfaces for chips, peeling, and other such defects.

Notify organizational maintenance personnel if surfaces re-

Par. 23

see fig. 1

Par. 23

see fig. 3

Par. 23

see fig. 3

Equipment --

-----------

----------quire refinishing.

a. Wipe dirt or other foreign matter from inside and outside of carrying case.

b. Straighten distorted or bent fasteners and aline with catches on cover of carrying case.

c. Clean accumulation of dirt and other foreign matter from high pressure hose.

d. Clean accumulation of dirt and other foreign matter from all components of the connector sets and replace on the mounting plates.

e. Clean accumulation of dirt and other foreign matter from the spray collector cup.

f. Store all equipment in carrying case,

See fig. 5

See fig. 5

Par. 23

see fig. 5

See fig. 6

Par. 23

see fig. 5

See fig. 5

Section IV. TROUBLESHOOTING

25. Purpose

Troubleshooting is a systematic determination of malfunctions and defective components by indications, symptoms, and tests. Close adherence to the procedures covered herein will materially reduce the time required to locate trouble and restore the materiel to normal operation.

Caution: Operation of the nozzle tester w i t h out preliminary examination can cause further damage to a disabled component. Be careful during inspection and troubleshooting, so that damage can be avoided.

26. Scope

This section covers troubleshooting

11

which is peculiar to the operator’s

(first echelon) maintenance operations.

27. Procedure

Malfunctions which may occur with the nozzle tester are listed in table

II. Upon observing any one of these malfunctions, take immediate steps to locate and correct the cause. Causes are listed opposite each malfunction and are arranged according to the ease of correction.

Table II. Troubleshooting

M a l f u n c t i o n P r o b a b l e c a u s e C o r r e c t i v e a c t i o n

1. Test fluid starvation.

2. Unable to build up hydraulic pressure on hydraulic pressure gage

(2, fig. 1).

a. Hydraulic pressure gage not threaded tightly into discharge block sub-assembly

Gage valve assembly not threaded tightly into discharge block sub-assembly a. Refer malfunc tion to organizational maintenance personnel for correction.

a. Tighten hydraulic pressure gage farther into discharge block subassembly

(fig. 4).

b. Tighten gage valve assem bly farther into discharge block subassembly

(fig. 4).

Table II. Troubleshooting – Continued

M a l f u n c t i o n P r o b a b l e c a u s e C o r r e c t i v e a c t i o n

3. Indications of test fluid leakage at plunger of body and plunger

(1-A, fig.

3).

c. Socket head cap screws loose in discharge block subassembly.

d. Loose connection to either the upper or lower discharge outlet

(3-D, and

3-E, fig. 1) 01

cap nut assembly

(3-F, fig. 1),

not tight on discharge outlet not in use.

e. Other causes --

c. Tighten socket head cap screws farther into discharge block sub-assembly

(4, fig. 3).

d. Tighten connection and cap nut assembly on discharge outlets.

e. Refer other causes to organizational maintenance personnel for correction.

Refer malfunction to organizational maintenance personnel for correction.

12

CHAPTER 4

ORGANIZATIONAL MAINTENANCE INSTRUCTIONS

Section I REPAIR PARTS, TOOLS, AND EQUIPMENT

28. General

Repair parts, tools, and equipment over and above those available of the operator are supplied by the using organization for maintaining the nozzle tester. Tools and equipment should be properly stored when not in use.

29. Repair Parts

Repair parts are supplied to the using organization for replacement of those parts most likely to become worn, broken, or otherwise unserviceable, provided that replacement of these parts is within the scope of organizational maintenance functions. Repair parts supplied for organizational maintenance of the nozzle tester are

listed in appendix IV.

30. Common Tools and Equipment

Common tools and equipment having general application of this materiel are authorized by tables of allowances and tables of organization and equipment.

31. Special Tools and Equipment

No tools or equipment specially designed for organizational maintenance are supplied or required for the nozzle tester.

Section Il.

P A I N T I N G

32. Painting

Instructions for the preparation of the materiel for painting, methods of painting, as well as a list of materials to be used are contained in TM 9-213. Materials for

painting are listed in appendix IV.

33. General

Refer to section III of chapter 3 for

preventive-maintenance services for the operator. These instructions apply equally to maintenance personnel of the using organization.

Section Ill. PREVENTIVE-MAINTENANCE SERVICE

34. Organizational Preventive-Maintenance

Services

No further preventive-maintenance services beyond that prescribed for the operator is required of maintenance personnel of the using organization.

Section IV. TROUBLESHOOTING

35. Purpose

Troubleshooting is a systematic determination of malfunctions and defective components by indications, symptoms, and

tests. Close Adherence to the procedures

covered herein will materially reduce the time required to locate trouble and restore the materiel to normal operation.

Caution: Operation of materiel without a preliminary examination can cause fur-

13

ther

damage to a disabled component. Be

careful during

inspection and troubleshooting, so that damage can be avoided.

36. Scope

This section covers troubleshooting which is peculiar to organizational (second echelon) maintenance operations. For troubleshooting procedures performed by

the operator, see paragraphs 25 through

27.

37. Procedure

Malfunctions which may occur with the

nozzle tester are listed in tables II and

III. In effect, table III is the continuation

of table II, paragraph 27. Causes are listed

opposite each malfunction and are arranged according to the ease of correction.

Table III. Troubleshooting

Malfunction P r o b a b l e c a u s e C o r r e c t i v e a c t i o n

1. Test fluid starvation

a. Filter element dirty or plugged up.

b. Leaking Orings, seal, or gaskets of filter assembly.

c. Other causes --

a. Replace filter element

(par. 39).

b. Discard old

O-rings, seal, or gaskets and replace with new parts

(par. 39).

c. Refer other causes to field maintenance e per-

Table III. Troubleshooting – Continued

M a l f u n c t i o n P r o b a b l e c a u s e C o r r e c t i v e a c t i o n

2. Unable to build up hydraulic pressure on hydraulic pressure gage

(2, fig. 1).

3. Indications of test fluid leakage at plunger of body and plunger

(l-A, fig.

3).

a. Defective gasket on gage valve assembly.

b. Dirt accumulation in discharge block assembly.

c. Defective valve gasket or Oring in discharge block assembly.

d. Scratched or scored valve seat.

e. Defective hydraulic pressure gage.

f. Other causes -sonnel for correction.

a. Discard old gasket and replace with new gasket

(par. 41).

b. Clean dirt from discharge block assem-

bly (2, fig. 4).

c. Discard old valve gasket and O-ring and replace with new gasket and

O-ring (par.

41).

d. Replace valve seat (par.

41).

e. Replace with new hydraulic pressure gage (par.

41).

f. Refer other causes to field maintenance personnel for correction.

Refer malfunction to field maintenance personnel for correction.

Section V. FUEL RESERVOIR ASSEMBLY

Note. The key numbers shown below in parentheses in this section refer to figure 3.

38. Description

The fuel reservoir assembly (2) is mounted on t o p of the body and plunger assembly (1) and consists primarily of a reservoir (2B), cover (2J), center rod assembly (2G), and filter element (2D). The reservoir assembly can be removed from the body and plunger assembly by taking the cover off the reservoir and unscrewing the center rod assembly. Test fluid used for testing the performance of fuel

injector nozzles is stored in the reser-

voir. The fluid is forced through the filter element to remove impurities.

39. Maintenance

a. General.

Organizational personnel has the authorization for the complete maintenance of the fuel reservoir assembly to the extent of removing, disassembling for inspection and replacement of all unserviceable components, and the final steps of assembling and installing the assembly.

14

b. Disassembly. Remove the cover (2J) from the reservoir (2B) by using a combined twisting and pulling motion. Unscrew the center rod assembly (2G) from the body and plunger assembly (1) and remove the

O-ring (2H). Slide the filter element (2D), filter washer (2E), and filter spring (2F) off the center rod assembly (2G). Remove the upper and lower filter gaskets (2C) from the filter element. Remove the reservoir (2B) from the body and plunger assembly (1) and the seal (2A) from the reservoir.

c. Cleaning. Clean the parts thoroughly with an appropriate solvent (par. 23).

d. Inspection and Repair.

(1) inspect the cover (2J), O-ring (2H), reservoir (2B), center rod assembly (2G), filter spring (2F), filter washer (2E), upper and lower gaskets (2C), and seal (2A) for being in good condition (par. 22b).

(2) Replace with new, the filter element (2D) and all other parts determined not in good condition.

e. Assembly. Install the seal (2A) on the bottom of the reservoir (2B) and mount the reservoir on top of the body and plunger assembly (1). Slide the filter spring (2F), filter washer (2 E), and O-ring

(2H) onto the center rod assembly (2G).

Place the upper and lower gaskets (2C) on the filter element (2D) and slide the filter element onto the center rod assembly (2G).

Screw the center rod assembly into the body and plunger assembly (1). Install the cover (2J) on the reservoir (2B).

Note.

One end of the filter element is red and marked “top”. Be sure the element is installed with this end in the upward position.

1 - Body and plunger assembly

A–Body and plunger

B–Handle

2 - Fuel reservoir assembly

A - Seal

B - Reservoir

C - Upper and lower gasket

D - Filter element

E - Filter washer

F - Filter spring

G - Center rod assembly

H - O-ring

J - Cover

3 - Discharge block assembly and hydraulic pressure gage

4 - Socket head cap screw

Figure 3. Fuel reservoir assembly,

15

Section VI. DISCHARGE BLOCK ASSEMBLY AND HYDRAULIC PRESSURE GAGE

N o t e . The key numbers shown below in parentheses in this section refer to figure 4 except where other-

w i s e i n d i c a t e d . ”

40. Description

The discharge block assembly and hy-

draulic pressure gage (3, fig. 3) is mounted

on the front of the body and plunger as-

sembly (1, fig. 3) and can be removed by

unscrewing four socket head cap screws

(4, fig. 3). It consists primarily of a cap

nut assembly (2E), discharge block subassembly (2F), gage valve assembly (2H) with handle (2J), filler rod assembly (2B), valve seat (2C), and hydraulic pressure gage (1). The flow of test fluid from the

reservoir assembly (2, fig. 3) is controlled

by the discharge block assembly by opening and closing the gage valve assembly (2H).

(2D) and all other parts determined not in good condition.

f. Assembly. Screw the cap nut assembly (2E) onto the discharge block subassembly (2 F). Place the valve O-ring (2D) on the valve seat (2C). Install the valve gasket (2A), valve seat (2C), filler rod assembly (2B) and valve gasket (2A) in the discharge block sub-assembly (2F).

Place the gasket (2G) on the gage valve assembly (2H) and screw the gage valve assembly into the discharge block subassembly. Screw the hydraulic pressure gage (1) into the discharge block subassembly. Install the discharge block assembly and hydraulic pressure gage (3,

fig. 3) on the body and plunger assembly

(1, fig. 3) and secure in place with the four socket head cap screws (4, fig. 3).

41.

Maintenance

a. General. Organizational personnel has the authorization for the complete maintenance of the discharge block assembly and hydraulic pressure gage to the extent of removing, disassembling for inspection and replacement of all unserviceable components, and the final steps of assembling and installing the assembly and gage.

h. Removal. Unscrew the four socket

head cap screws (4, fig. 3) and remove

the discharge block assembly and hydrau-

lic pressure gage (3, fig. 3) from the body and plunger assembly (1, fig. 3).

c. Disassembly. Remove the hydraulic pressure gage (1) by unscrewing it from the discharge block sub-assembly (2F).

Unscrew the gage valve assembly (2H) with handle (2J) and remove the gasket

(2G). Remove the cap nut assembly (2E), valve gaskets (2A), filler rod assembly

(2B), and valve seat (2C) from the discharge block sub-assembly (2F). Remove the valve O-ring (2D) from the valve seat

(2C).

d. Cleaning. Clean the parts thoroughly

with an appropriate solvent (par. 23).

e. Inspection and Repair.

(1) Inspect the filler rod assembly

(2B), valve seat (2C), gaskets (2A and 2G), cap nut assembly (2 E), and gage valve assembly (2H) for

(2)

being in good condition (par. 22b).

Replace with new the valve O-ring

F i g u r e 4 . . D i s c h a r g e b l o c k a s s e m b l y

and hydraulic pressure gage.

16

CHAPTER 5

SHIPMENT AND ADMINISTRATIVE STORAGE AND

DEMOLITION TO PREVENT ENEMY USE

4 2 .

Section I. SHIPMENT AND ADMINISTRATIVE STORAGE

Shipping Instructions a.

Responsibility. When shipping the nozzle tester, the unit commander will be responsible for shipping the materiel, including all tools and equipment, adequately processed, packaged, and packed to protect it from damage until it reaches the echelon of maintenance for required repairs; or, in the case of troop movement, reaches its destination in a serviceable condition.

b. Army Shipping Documents. Prepare all army shipping documents in accordance with AR 725-50.

c. Preparation for Shipment. When the nozzle tester is removed from administrative storage for shipment it need not be reprocessed unless inspection reveals it to be inadequately preserved, or when it is necessary because of anticipated intransit weather or shipping conditions.

Preservatives must not be removed or disturbed, except as necessary, to insure that the nozzle tester is complete and serviceable. If preservatives are removed, they must be restored prior to shipment.

43. Preservation, Packaging, Pocking,

and Marking Instructions.

a. Preservation and Packaging. Preservation of the nozzle tester must be sufficient to protect it against deterioration and damage during shipment and administrative storage and/or the subsequent interval prior to use. Under no condition will tools and equipment with critical surfaces be packaged without benefit of sufficient preservation to assure adequate protection (TM 9-200). Preservation and packaging must be compatible with end use requirements.

b. Packing. Packed items must be acceptable to the carrier, while affording adequate protection to the items during shipment and administrative storage and/ or the subsequent interval prior to use.

c. Marking. All materiel will be marked in accordance with TM 9-200.

44. Administrative Storage

a. General.

(1) Unit commander? may, with the approval of major commanders, place the nozzle tester in administrative storage or return to supply agencies equipment that is beyond the maintenance capability of the unit. Nozzle testers must be stored in the most favorable 10 cation

(2)

(3) available, preferable one which affords protection from exposure to elements and pilferage.

All nozzle testers in administrative storage must be maintained so that they will be ready for immediate use and/or ready for shipment.

Administrative storage is restricted to a period of 90 days and must not be extended unless the nozzle tester is reprocessed.

b. Storage Procedures.

(1) Perform a quarterly preventivemaintenance (PM) service on the nozzle tester. This maintenance

(2)

(3) will consist of inspecting, cleaning, servicing, and preserving, as required, and will also include minor repair parts replacement (if required) not requiring highly technical skills or expensive, complicated, or bulky test equipment or tools.

Provide access to the nozzle tester to p e r m i t inspection, servicing, and removal from storage.

Mark the nozzle tester “Administrative Storage” (by use of tags or

17

other convenient method). The noz zle tester so marked must not be operated while in this category.

c. Inspection in Administrative Storage.

Visual inspection of the nozzle tester in administrative storage must be conducted at least once each month to detect corrosion and rust, When corrosion and rust are found, corrective action must be taken immediately. A record of these inspections must be maintained for each nozzle tester in administrative storage. The records must be attached to the nozzle tester in such a manner as to protect it from the elements.

Section Il. DEMOLITION OF MATERIEL TO PREVENT ENEMY USE

45. General

a. Destruction of the nozzle tester, when subject to capture or abandonment in the combat zone, will be undertaken by the using army only when, in the judgment of the unit commander concerned, such action is necessary in accordance with orders of, or policy established by, the army commander. When in the hands of maintenance personnel or in storage, destruction will be in accordance with FM 9-5 and the information below, when applicable.

b. The information which follows is for guidance only. Certain phases of the procedures outlined require the use of explosives and incendiary grenades which normally may not be authorized items of issue to the using organization. The issue of these and related materials and the conditions under which destruction will be effected are command decisions in each case, according to the tactical situation.

Of the several means of destruction, those most generally applicable are:

Mechanical . . . . Requires axe, pick mattock, sledge, crowbar, or similar implement.

Burning . . . . . . Requires gasoline, oil, incendiary grenades, or other flammables, welding or cutting torch.

Disposal . . . . . Requires burying in the ground, dumping in streams or marshes, or scattering so widely as to preclude recovery of essential parts.

*Demolition . . . Requires suitable explosive or ammunition.

*Gunfire . . . . , Includes artillery, machine guns, rifles using rifle grenades, and launchers using antitank rockets. U n de r some circumstances, hand grenades may be used.

In general, destruction of essential parts, followed by burning, will usually be sufficient to render the material useless. However, selection of the particular method of destruction requires imagination and resourcefulness in the utilization of the facilities at hand under the existing conditions. Time is critical.

c. If destruction to prevent enemy use is resorted to, the materiel must be so badly damaged that it cannot be restored to a usable condition in the combat zone either by repair or cannibalization. Adequate destruction required that all parts essential to the operation of the materiel be destroyed or damaged beyond repair. However, when lack of time and personnel prevents destruction of all parts, priority is given to the destruction of those parts most difficult to replace. Equally important, the same essential parts must be destroyed on all like materiel, so that the enemy cannot construct one complete unit from several damaged ones.

d. If destruction by demolition or gunfire is directed, due consideration should be given to the observance of appropriate safety precautions.

*Generally applicable only when nozzle tester is to be destroyed in conjunction with other equipment.

18

46. Destruction of the Nozzle Tester a. Method No. 1 - Destruction by Mechanical Means.

(1)

(2)

(3)

Open the carrying case and remove the nozzle tester, connector sets, hose, and spray collector cup.

Using an axe, pick mattox, sledge, or any other heavy implement, destroy the nozzle tester by smashing the body casting, fluid reservoir, and hydraulic gage,

Destroy the carrying case and spray collector cup by smashing.

Cut the hose in short lengths, and scatter the connector sets.

Elapsed time: about 2 minutes.

b. Method No. 2- Destruction by Burning,

(1) Open the carrying case and remove the nozzle tester, connector sets, hose, and spray collector cup.

(2) Using a welding or cutting torch, burn through the body casting, fluid reservoir, hydraulic gage, carry-

(3) ing case, spray collector cup, hose, and connector sets.

In the absence of a welding or cutting torch, place piles of combustible materiel on and about the nozzle tester. Pour gasoline or oil over the combustible materiel and the nozzle tester, ignite by means of an incendiary grenade fired from a safe distance, by a combustible train of suitable length, or other appropriate means. Take c o v e r immediately. A hot fire is required to render the materiel useless.

Elapsed time: about 4 minutes.

Warning: When igniting gasoline, due consideration should be given to the highly flammable nature of gasoline and its vapor. Carelessness in its use may result in fatal or painful burns.

c. Method No. 3- Destruction by Dis-

posal. Bury the nozzle tester in a suitable hole or throw it into a stream.

Elapsed time: about 2 minutes.

19

APPENDIX I

REFERENCES

1. General a. Military Publications.

The packaging publications listed herein are available to activities requiring such publications. Forward requests for Military Specifications to

Naval Supply Depot, 5801 Tab or Avenue, Philadelphia, Pennsylvania. Requisition technical manuals, technical bulletins, supply bulletins, and other publications indexed in 310 series DA pamphlets in accordance with AR 310-1.

b. Commercial Publications. Commercial publications listed herein may be obtained from the following addresses: Uniform Freight Classification Rule and Containers

Specifications for Rail Shipment; Uniform Classification Committee, 202 Union Station,

Chicago 6, Illinois; National Motor Freight Classification Rules and Container Specifications for Truck Shipment; American Trucking Association, 1424 16th Street, N. W.,

Washington 6, D.C.

2. Army Regulations

Issue of Supplies and Equipment: Requisitioning, Receipt, . . . . . . . . . AR 725-50 and Issue System.

Logistics (General): Report of Damaged or Improper Shipment . . . . . . AR 700-58

Maintenance of Supplies and Equipment: Organizational . . . . . . . . . . . AR 750-5

Policies, and Responsibilities for Maintenance Operations.

Military Publications: General Policies. . . . . . . . . . . . . . . . . . . . . . AR 310-1

Safety: Accident Reporting and Records . . . . . . . . . . . . . . . . . . . . . AR 385-40

3. Publications Indexes

The following publications indexes should be consulted frequently for latest changes or revisions of references given in this appendix and for new publications relating to materiel covered in this manual.

Index of Army Motion Pictures, Film Strips, Slides . . . . . . . . . . . . . . DA Pam 108-1 and Phono-Recordings.

Militarv publications:

Index-of Administrative Publications. . . . . . . . . . . . . . . . . . . . . . . DA Pam 310-1

Index of Blank Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. DA Pam 310-2

Index of Graphic Training Aids and Devices . . . . . . . . . . . . . . . . . . DA Pam 310-5

Index of Technical Manuals, Technical Bulletins, . . . . . . . . . . . . . . DA Pam 310-4

Supply Bulletins, Lubrication Orders, and Modification Work

Orders.

Index of Training Publications . . . . . . . . . . . . . . . . . . . . . . . . . .. DA Pam 310-3

4. Field Manuals

Explosives and Demolition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. FM 5-25

Ordnance Direct Service Report . . . . . . . . . . . . . . . . . . . . . . . . . .. FM 9-3

Ordnance Ammunition Service. . . . . . . . . . . . . . . . . . . . . . . . . . .. FM 9-5

Military Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. FM 21-5

Techniques of Military Instructions. . . . . . . . . . . . . . . . . . . . . . . . . FM 21-6

20

5. Forms

The following forms pertain to this materiel:

DA Form 468, Unsatisfactory Equipment Report.

DA Form 1115, Property Turn/In Tag (tag),

DA Form 2028, Recommended Changes to DA Technical Manual Parts List or Supply

Manual 7, 8, or 9 (cut sheet).

DD Form 6, Report of Damaged or Improper Shipment (cut sheet).

DD Form 250, Materiel Inspection and Receiving Report.

DD Form 1149, Requisition and Invoice/Shipping Document (cut sheet).

DD Form 1348, DOD Single Line Item Requisition System Document (Manual).

6. Other Publications a. General.

Dictionary of United States Army Terms . . . . . . . . . . . . . . . . . AR 320-5-1

Military Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FM 21-30/AFM 55-3

Military Terms, Abbreviations, and Symbols: Authorized . . . , . . AR 320-5

Abbreviations and Brevity Codes.

The Army Equipment Record System and Procedures. . . . . . . . . TM 38-750 b. Cleaning.

Cleaning Compound, Alkali Type. . . . . . . . . . . . . . . . . . . . . P-C-436

Cleaning Compound, Solvent and Self-Emulsifying . . . . . . . . . . . MIL-S-11090

Cleaning Compound, Synthetic Detergent, Nonabrasive, . . . . . . . P-C-431

All-Purpose.

General Packing Instructions for Ordnance General Supplies . . . . TM 9-200

Material Used for Cleaning, Preserving, Abrading, and . . . . . . . TM 9-247

Cementing Ordnance Materiel; and Related Materials

Including Chemicals.

Rag, Wiping, Cotton, Sterilized, Undyed, Class 1 or 2 . . . . . . . . . DDD-R-30

Solvent, Dry Cleaning.....,.. . . . . . . . . . . . . . . . . . . . . .. P-S-661 c. Paint Remover.

Remover, Paint (alkali type) . . . . . . . . . . . . . . . . . . . . . . . . .TT-R-230

Remover, Paint and Varnish (Alkali Organic-Solvent Type) . . . . . MIL-R-12294 d. Painting.

Enamel, Gloss, Synthetic (for Exterior and Interior Surfaces) . . . TT-E-489

Painting Instructions for Field Use . . . . . . . . . . . . . . . . . . . . . TM 9-213

Primer Coating, Synthetic, Rust Inhibiting, Lacquer-Resisting. . . TT-P-664 e. Packaging

Barrier Material, Paper, Noncorrosive . . . . . . . . . . . . . . . . . . MIL-B-130

Barrier Material, Water Vaporproof, Flexible MIL-B-131

Boxes, Fiber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. PPP-B-636

Cushioning Material, Cellulosic . . . . . . . . . . . . . . . . . . . . . . . PPP-C-843

Desiccants, Activated, Bagged, Packaging Use and. . . . . . . . . . . MIL-D-3464

Static Dehumidification.

Tape, Pressure Sensitive Adhesive, Paper, Water-Resistant . . . . PPP-T-76 f. Shipping and Storage.

National Motor Freight Classification Rules and Container

Specifications for Truck Shipments.

Protection of Ordnance General Supplies in Open Storage . . . . . . TM 9-244

Uniform Freight Classification Rules and Container

Specifications for Rail Shipments.

21

APPENDIX II

BASIC ISSUE ITEMS LIST

Section I.

P R E F A C E

1. General

This appendix is a list of basic issue list items. It is composed of those items which make up the major end items of equipment and the first echelon tools, supplies, assemblies, and repair parts that are issued with the equipment and are required for stockage.

2. Requisition Notes

See appendix IV, paragraph 2.

3. Explanation of Columns a. Source, Maintenance, and Recoverability

(1)

Code (Col. 1).

Material numerical codes (col. 1a).

This column indicates the responsible commodity command for the materiel. The commodity command responsible for supply of items in this list are:

Code

9

Type Materiel

Ordnance Materiel

(2) Source (col. lb). This column indicates the selection status and source for the listed item. Source codes used in this list are:

Code Explanation

C Obtain through local procurement. If not obtainable from local procurement, requisition through normal supply channels with a supporting statement of nonavailability from local procurement.

(3)

(4)

Maintenance level (col. 1c). This column indicates the lowest maintenance echelon authorized to install the listed item. Maintenance level codes used in this list are:

Code Explanation

O Organizational maintenance (lst and

2d echelon).

Recoverability (col. 1d). This col-

22

umn indicates whether unserviceable items should be returned for recovery or salvage. When no code is indicated, the item will be considered expendable. Recoverability codes used in this list are:

Code Explanation

R Items which are economically repairable at field maintenance activities (3d and 4th echelon) and are normally furnished by supply on an exchange basis.

b. Federal Stock Number (Col. 2). This column indicates the Federal stock number which has been assigned by the Cataloging Division, Defense Logistics Services Center.

c. Description (Col. 3). This column indicates the Federal item name (shown in capital letters) and any additional description required for supply operations. The manufacturer’s code and part number is also included for reference.

Code

05083

Explanation

Bacharach Industrial Instrument

Company

d. Unit of Issue (Col. 4). This column indicates the quantity to be requisitioned.

e. Quantify Authorized (Col. 5). This column indicates the quantity of the listed item authorized for stockage to constitute the prescribed load.

f. Illustration (Col.. 6). This column indicates the figure number of the illustration that depicts the listed item. When more than one item appears on an illustration, the item number is also indicated.

4. Special Information

Repair parts and special tools required for organizational maintenance of the noz-

zle tester are listed in appendix IV of

this manual.

5. Abbreviations

Abbreviation dwg . . . . . . . . .

e a .

no. . . . . . . . . . .

Ord . . . . . . . .

Explanation

. . . . . . . . . . . .

drawing(s)

. . . . . . . . . . . .

each

. . . . . . . . . . . .

number(s)

. . . . . . . . . . . .

Ordinance

6. Suggestions and Recommendations

The direct reporting of errors, omissions and recommendations for improving this technical manual by the individual user, is authorized and encouraged, DA

Form 2028 will be used for reporting these improvements. This form may be completed using pencil, pen or typewriter.

DA Form 2028 will be completed in triplicate and forwarded by the individual using the manual. The original and one copy will be forwarded direct to:

Commanding General

Headquarters, U. S. Army Weapons

Command

ATTN: AMSWE-SMM-TE

Rock Island Arsenal

Rock Island, Illinois, 61202

One information copy will be provided to the individual’s i m m e d i at e supervisor

(e.g., officer, noncommissioned officer, supervisor, etc.).

23

24

(1)

Source, maintenance, and recoverability code

(2)

Section II. BASIC ISSUE ITEMS

(3)

Federal stock

No.

Description

---c c c c c o

0

0

0

0

—.

R

----

----

----

-------------

-------------

------------—

----

----

~910-255-8641

!910-955-5517

!910-955-5516

MAJOR COMBINATION

TESTER, DIESEL FUEL INJECTOR NOZ-

ZLE: (05083 :YFL).

COMPONENTS OF MAJOR COMBINATION

None authorized.

REPAIR PARTS

None authorized.

TOOLS AND EQUIPMENT :

T 00LS

None authorized.

EQUIPMENT

CASE, CARRYING: (05083:65-808) --------

CUP, COLLECTOR: (05083 :65-317) ------

HOSE , PRESSURE, HIGH: (05083 :65-284) --

The following equipment used in conjunction with the nozzle tester is to be requisitioned on an “as required” basis.

(FSN’S 4910-955-5517 and 4910-955-5516)

CONNECTOR SET, FUEL INJECTOR :

(05083 :65-275 )(see applicable TM’s).

CONNECTOR SET, FUEL INJECTOR:

(Oral dwg no. Bl1020498)(for LDS-427 and

1790 series Continental Engines and others.

See applicable TM’s).

ea ea ea ea set set

----

1

1

1

1

1

1

5

5

5

6

6

(6)

Ill”stre.t, on

Figure 5. Equipment

Figure 6. Equipment

25

APPENDIX III

MAINTENANCE ALLOCATION CHART

1. Purpose

The maintenance allocation chart allocates specific maintenance operation to the proper level.

2. Basis

Allocation of maintenance operations is made on the basis of time, tools, and skills normally available to the various echelons in a combat situation and influenced by maintenance policy and sound maintenance practices as outlined in AR 750-5.

3. Explanation and Definitions

The maintenance allocation chart designates overall responsibility for the maintenance function of an end item or assembly. Repair and/or rebuild of major assemblies is designated by authority of the Army Commander representative, except for the specific subfunctions listed in the maintenance allocation chart. Deviations from maintenance operations allocated to the maintenance allocation chart is authorized only upon approval by the

Army Commander representative.

SERVICE To clean, to preserve, and to replenish fuel and lub-

ADJUST ricants.

To prevent or correct malfunction by maintaining prescribed limits or by bringing into proper or exact position.

INSPECT

TEST

To verify serviceability and to detect incipient electrical or mechanical failure by scrutiny.

To verify serviceability and

REPLACE

REPAIR

REBUILD

SYMBOL X to detect incipient electrical or mechanical failure by use of special equipment such as gages, meters, etc.

T o s u b s t i t u t e s e r v i c e a ble assemblies, sub-assemblies, and parts for unserviceable components.

To restore to a serviceable condition by replacing unserviceable parts, or by any other action required; utilizing tools, equipment, and skills available to include w e 1 d i n g, riveting, s t r a i g h t e n i n g , a d j u s t ing, etc.

To restore to a condition comparable to new by disassembling the item to determine the condition of each of its component parts and reassembling it using serviceable, rebuilt, or n e w a s s e m b l i e s , s u b assemblies, and parts.

The symbol X placed in the appropriate column indicates the echelon responsible for performing that particular maintenance operation but does not necessarily indicate that repair parts will be stocked at that level. Echelons higher than the echelon marked by X are authorized to perform the indicated operation.

26

(1)

Grp

No.

Maintenance A Uocation Chart for Tester, Diesel

Fuel Injector Nozzle

~>]

Component and Related

Operations m

Ist

:4)

> nd m

Ird

(6)

1 th

(7)

5th

1 Tester, Nozzle:

Service -----------------

Adjust ------------------

Inspect -----------------

Test -------------------

Repair -----------------

2 Body and Plunger Assembly service -----------------

Inspect -----------------

Repair ------------------

Rebuild(Plunger Assembly) x x x x x x x x x

(1)

GrP

No.

(2)

Component and Related

Operations

3 Discharge Block Assembly

Service -----------------

Inspect -----------------

Repair ------------------

4 Fuel Reservoir Assembly

Service -----------------

Iospect -----------------

Repair ------------------

5 Hydraulic Pressure Gage

Service -----------------

Inspect -----------------

Repair ------------------

(3)

[St

(Ij lnd

(5)

\rd

“6) th

(7)

5th x x x x x x x x x

.

27

APPENDIX IV

REPAIR PARTS AND SPECIAL TOOL LISTS

Section I PREFACE

1. General

a. This appendix is a list of repair parts which may be required by the using organization for performing organizational maintenance but are not authorized to be stocked. These items are to be requisitioned as required for immediate use only.

b. For prices of items of Ordnance materiel, see the appropriate supply manual of the SM 9-2 series. Prices of items that are the responsibility of other commodity commands may be obtained from the appropriate type 2 supply manuals for those commands.

c. Additional applications of items in this manual are listed in the supply manuals of the SM 9-3 series.

2. Requisition Notes a. Repair Part Identified by Federal

Stock Number.

(1) If the exact item requisitioned is

(2) not furnished, or if other action is necessary, the exact nature of the action taken by the commodity command will be indicated by standard symbols on prescribed forms.

When requisitioning an item, the requesting agency will order the

listed item. However, the commodity command will take necessary action to issue the exhaust stock item until stock is exhausted, whether it be an individual item, kit, set, or assembly.

(3) Requisition for replacement of items that are the responsibility of commodity commands will be submitted to the commodity command indicated in column 1a, Materiel Code Number.

b. Part to which FSN has not been as-

28 signed. When requisitioning a C source

(local procurement) item identified only by a manufacturer’s part number, it is mandatory that the following information be furnished the supply officer:

(1) Manufacturer’s code number (5

(2) digit number preceding the colon in the descriptive column).

Manufacturer’s part number (the number, and sometimes letters, following the colon, (1) above).

Dashes, commas, or other marks must be included exactly as listed.

(3)

(4)

Noun name and dimensions, if necessary.

Name of manufacturer of end item

(from cover of TM or manufacturer’s name plate).

(5)

(6)

(7)

Federal stock number of end item

(from TM).

Manufacturer’s model n umber

(from TM or name/data plate, preferably name/data plate).

Manufacturer’s serial number

(from name/data plate).

(8)

(9)

Any other information such as type, frame number, and electrical characteristics, if applicable.

If DD Form 1348 is used, fill in all blocks except 4, 5, 6, and Remarks field in accordance with AR 725-50.

(a)

Complete form as follows:

In blocks 4, 5, and 6, list manufacturer’s code, and manufac-

(b) turer's part number (as listed in description column).

In Remarks field, list noun name

(repair part), end item application (FSN of end item), manufacturer, model number (end item), serial number (end item), and any other pertinent information such as frame number, type, etc.

3. Explanation of Columns a. Source, Maintenance, and Recoverability Code (Col. 1).

(1) Materiel Numerical Codes (col.

1a). This column indicates the responsibility commodity command for the materiel. The commodity command responsible for supply of items in this list are:

Code

9

10

3

5

Type materiel

Chemical Materiel

Engineers Materiel

Ordnance Materiel

Quartermaster Materiel

(2) Source (col. 1b). This column indicates the selection status and source for the listed item. Source codes used in this list are:

(3)

Code Explanation

C Obtain through local procurement. If not obtainable from local procurement, requisition through normal supply channels with a supporting statement of nonavailability from local procurement,

Maintenance level (col. 1c). This column indicates the maintenance echelon authorized to install the listed item. Maintenance level codes used in this list are:

Code Explanation

O Organizational maintenance (lst and

2d echelon).

(4) Recoverability (col. 1d). This column indicates whether unserviceable items should be returned for recovery or salvage. When no code is indicated, the item will be considered expendable.

b. Federal Stock Number {Col. 2). This column indicates the Federal stock number which has been assigned by the Cataloging Division, Defense Logistics Services Center.

c. Description (Col. 3). This column indicates the Federal item name (shown in capital letters) and any additional description required for supply operations. The manufacturer’s code and part number is also included for reference.

Code

05083

Explanation

Bacharach Industrial Instrument

Company

d. Unit of Issue (Col. 4). This column indicates the quantity to be requisitioned.

e. Quantity Incorporated in Unit (Col. 5).

This column indicates the total number of times the listed item is used in the end item (major item) or major combination.

Where no quantity is shown, reference should be made to the first appearance of the item as indicated in the “description” column.

f. 15-Day Maintenance Allowance (Col.

6). This column indicates the quantitative allowance for second echelon of the listed items. These allowances represent one prescribed load, for a 15-day period, for the number of major items supported.

They must be on hand or on order at all times. Major commanders will determine the number of prescribed loads second echelon units will carry. Units and organizations authorized additional prescribed loads will multiply the number of equipments supported by the number of prescribed loads. Additional repair parts which may be required for performing authorized maintenance, but are not authorized for stockage in the prescribed load, are indicated by an asterisk (*). These items are to be requisitioned as required for immediate use only. Where no quantity is shown, reference should be made to the first appearance of the item as indicated in the “description” column.

Note. The 15-day level is not applicable to special tools for organizational maintenance.

g.

Illustration (Col. 7). This column indicates the figure number of the illustration that depicts the listed item. When more than one item appears on an illustration, the item number is also indicated.

4. Special Information

Basic issue items are listed in appen-

dix II of this manual.

5. Abbreviations and Symbols a. Abbreviations.

Abbreviation Explanation a s s y . . . . . . . . . . . . . . . assembly cntr . . . . . . . . . . . .. container deg . . . . . . . . . . . . . . . . .. degree(s) dr . . . . . . . . . . . . . . . . . .. drum

29

Abbreviation ea.. . . . . . . . . . . . . . . . . .

F . . . . . . . . . . . . . . . . . . .

Fed . . . . . . . . . . . . . . . . . . fl . . . . . . . . . . . . . . . . . .

ga . . . . . . . . . . . . . . . . . .

gal . . . . . . . . . . . . . . . . . . .

hex . . . . . . . . . . . . . . . . . .

hr . . . . . . . . . . . . . . . . . . .

in. . . . . . . . . . . . . . . . . . .

lb . . . . . . . . . . . . . . . . . . .

lg . . . . . . . . . . . . . . . . . . .

it . . . . . . . . . . . . . . . . . . .

max. . . . . . . . . . . . . . . . . .

ML . . . . . . . . . . . . . . . . . .

min . . . . . . . . . , . . , . . . . .

mtl . . . . . . . . , . . . . . . . . .

no. . . . . . . . . . . . . . . . . . .

od. . . . . . . . . . . . . . . . . . .

oz. , . . . . . . . . . . . . . . . . , pt . . . . . . . . . . . . . . . . . . .

qt . . . . . . . . . . . . . . . . . . .

ro . . . . . . . . . . . . . . . . . .

sq. . . . . . . . . . . . . . . . . . .

thk . . . . . . . . . . . . . . . . . .

w . . . . . . . . . . . . . . . . . . .

w/ . . . . . . . . . . . . . . . . . .

ye . . . . . . . . . . . . . . . . . . .

Explanation each

Fahrenheit

Federal flat gage gallon(s) hexagon hour(s) inch(es) pound length (long) l i g h t w e i g h t ) maximum military minute metal number o u t s i d e d i a m e t e r ounce(s) point quart(s) roll square thickness) wide, width with yard(s) b. Symbols.

Symbols Explanation

. . . . . . . . . . . . . . . . . . . . . . . . as required

. . . . . . . . . . . . . . . . . . . . . . . . see par. 3f

6. Suggestions and Recommendations

The direct reporting of errors, omissions and recommendations for improving this technical manual by the individual user, is authorized and encouraged. DA

Form 2028 will recompleted in triplicate and forwarded by the individual using this manual. The original and one copy will be forwarded direct to:

Commanding General

Headquarters, U. S. Army Weapons

Command

ATTN: AMSWE-SMM-TE

Rock Island Arsenal

Rock Island, Illinois, 61202

One information copy will be provided to the individual’s immediate supervisor

(e.g., officer, noncommissioned officer, supervisor, etc.).

30

-—

,1} source, mfiintenmc?, and recovembi!lty code

(d) h

-.

.C

6 z

:

,;

Section II. REPAIR PARTS AND SPECIAL TOOLS

(2)

Federal etock

No.

Description

9

9

9

9

9

9

9

9

9

9

9

9

9

I

I i c c c c c c c c c c c c’ c c c c c c c c

1 o

0

0

0

0

0

0

0

0

0 c) o

0

0

0

0

0

0

0

0

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

.----_--_.---

-------------

-------------

-------------

.-_----_-----

.------------

.------------

.------------

-------------

-------------

-------------

-------------

-------------

.------------

-------------

-------------

-------------

._-_-----_---

.------------

REPAIR PARTS FOR:

Discharge Block aud Hydraulic

Pressure Gage Groups

BLOCK, DISCHARGE: assy (05083:65-

949).

BLOCK, SUB, DISCHARGE: assy

(05083:65-561).

GASKET, GAUGE, VALVE: (05083:65-

505).

GASKET, VALVE, DISC HARGE :

(05083:65-507).

PACKING, PREFORMED: (O-RING) valve, discharge (05083 :65-550).

ROD, FILLER: assy (05083:65-803),

SEAT, VALVE, DISCHARGE: (05083:

65-358).

VALVE, GAUGE: assy (05083:65-553),

GAUGE, PRESSURE HYDRAULIC :

(05083:65-534).

rhe following parts are not authorized for replacement by orga nizatioual maintenance.

2E - Cap nut assembly (05083:65-

582)

2J - Valve handle (050!33 :65-622)

Fuel Reservoir and Body and Plunger

Groups

FUEL RESERVOIR: assy (05083:65-

947).

COVER, RESERVOIR, FU EL:

(05083:65-787).

FILTER, FUEL: (05083:65-788) ----

GASKET, FILTER: (05083:65-761) --

PACKING, PREFORMED: (O-RING) rod, center (05083:65-790),

RESERVOIR, FUEL: (05083:65-786).

ROD, CEiSTER: assy (05083:65-789)

SEAL, RESERVOIR TO BODY,

FUEL: (05083:65-797).

SPRING, FILTER: (05083 :65-791 )---

WASHER, FILTER: (05083 :65-739)--

HANDLE, PUMP: assy (05083:65-802)

I’he following parts are not authorized for replacement by organizational maintenance.

1- Plunger and bodj assembly

(05083:65-948),

1A- Plunger and body

3- Discharge block assembly and hydraulic pressure gage

(Note: Sec Figure 4)

ea ea e~ ea ea

<Xl ea

W ea ea ea ea ea ea ea ea ea ea ea ea

1

1

1

2

1

1

1.

1

3.

1

1

1

1

1

1

2

1

1

1

1

*

*

*

*

*

*

*

*

*

* m

*

*

*

*

*

*

*

*

,$.

(7)

Illustration

2

2F

2G

2A

2D

2B

2C

2H

1

4

4

4

4

4

4

4

4

4

2

ZJ

2D

2C

2H

2B

2G

2A

2F

2E lB

3

3

3

3

3

3

3

3

3

3

3

31

3 2

(1)

(a) maintenance, mfl nxoveratl) I !ty’ code

(2)

Federal stock

No.

(3)

Description

REPAIR PARTS FOR – Continued

Fuel Reservoir and Body and Plunger

Groups — Continued

4- Socket head cap screw (05083:

65-508).

SPECIAL TOOLS

None authorized.

TOOLS AND EQUIPMENT :

TOOLS

None authorized.

I

EQUIPMENT

Appendix II of this manual oontains

list of equipment required for operational and organizational maintenance.

I

I

(4) (7)

111 ustrati on

(1)

1, .a

,s

C,urc, e .

maintenanw, and recovorabtllty code

——

(h] (c,

(d)

6

;

.r;

*

>

:

:?

4 ~,

,5 -

:

~

: d.

;

>

: b s

(2)

Federal stock

No.

(3)

Description

10

5

3

3

10

3

9

9

9

10

9

10

10

10

10

5

!5

5

----

----

---6850-368-5227

----

----

----

----

----

—---

8135-282-0565

8020-545-8517

----

----

----

----

----

----

6850-598-3057

6850-224-6661

----

----

----

----

----

----

6850-224-6665

6850-224-6666

----

----

----

----

----

----

8135-558-0823

8135-183-8815

----

----

----

----

----

----

----

--—-

----

6850-264-6568

6850-264-6573

7930-249-8036

----

----

----

----

----

----

----

----

—---

6850-281-1986

6850-285-8011

6850-637-6135

--—-

----

----

----

----

----

----

----

----

8010-298-2300

8010-286-7749

$010-286-7749

CLEANING, PRESERVING AND

PACKAGING MATERIALS

ANTISTATIC AND CLEANERCOM-

POUND: petroleum base, liquid form, colorless, transparent,

MIL-C-12156

5 oz can-----------------------

BARRIER MATERIAL, WATER-

VAPORPROOFED, FLEXIBLE:

MIL-B-131.

Glass Length, Yards Width, Inches

1 200 36

BRUSH, PAINT: fl, hog bristle, w/ sqedge, l-7/16w, 9/16 thk, 1-3/4 exposed lg.

CLEANING COMPOUND, SOLVENT: alkali type, Fed P-C-436a.

351b pail ---------------------

100lbpaiI ---------------------

CLEANING COMPOUND, SOLVENT: self-emulsifying MIL-S-1109O.

5galcntr ---------------------

55galdr -----------------------

CUSHIONING MATERIAL, PACKAG-

ING: cellulose wadding (nonbound), type III, class B, waterresistant, roll Fed PPP-C-843.

Length,

Feet

66

Width,

Inches

20

‘hickness

1.000

99 20 0.500

DESICCANT, ACTIVATED: class2

MIL-D-3464

Units per

Bag

1/2

2

Bags per

Container Container

600

200 5

Size of

5 gal can

gal can

DETERGENT, PAINTED SURFACE: powdered, used for general cleaning, Fed P-C-431a, type I, 5 lb pail

DRY CLEANING SOLVENT: liquid form, to remove soil from surfaces in dry cleaning process, petroleum distillate, 140 deg F flasl pt, Fed P-S-661, type If.

55galdr(16ga) ---------------

55galdr(18ga) --------------bulk --------------------------

ENAMEL: full gloss, 8 hr max air dry hard time, gray color no.

16187, Fed TT-E-489, class A.

lqtcan -----------------------

1 gal can ----------------------

5 gal can ----------------------

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

#

#

+

+#

+

++

##

$

&

#+

+

+#

(i’)

Illustration

(a)

~ g

.w k

33

1 ) (2) (3)

(a) m~intenanre, t%.. d recover ah, i]ty CCXIC.

(b)

(.)

Federal stock

90.

Description

-i

‘~ :

$0 g.

.

al

0

~ cc

———

——

10

10

10

10

10

10

10

10

10

10

10

9

10

10

5

9

.5

9

5

5

:

:Z

CJ>

.

.3

a!

F

----

----

----

----

----

----

----

----

----

----

----

----

----

----

----

-------

----

----

----

----

----

----

----

----

----

----

----

----

----

----

-------

----

----

----

----

----

----

----

----

----

----

8135-281-4112

8135-281-4113

8135-281-9067

8135-281-4115

----

----

----

----

-----

----

----

----

----

----

----

----

----

----

----

----

8135-281-4120

8135-281-4121

8135-281-5105

8135-281-5106

8135-664-0028

8010-161-7274

8010-161-7275

7920-234-8462

7920-205-1711

8010-283-0511

8011’ --28051111

8010 -227 -16’34

8010-227-1693

8135-297-6655

8135-297-6656

8010-242-2089

CLEANING, PRESERVING AND

PACKAGINGMA TERIALS-Continued

FIBERBOARD, CORRUGATED: double face, class 3, grade 3 (V3C),

Fed PPP-B-636.

Length, Inches Width, Inches

84

120

96

36

36

48

96 60

FIBERBOARD, CORRUGATED: double face, class 3, grade 5 (W5C)

Fed PPP-J3-636.

Length, Inches

84

120

96

Width, Inches

36

36

60

72 72

PAPER, WRAPPING, LAMINATED

ANI)CREPED: type I, MIL-%-130.

Length, Yards Width, Inches

100 36

PRIMER, COATING: 30 min max air drying time for recoatin~, ~cxl

TT-P-664.

1 gal can ----------------------

5 gal can -----------------------

RAG, WIPING: cotton, s~erilized, unbleached, white, designed for gener~l purpose use, Fed DDD-R-

30, class H.

51b bag ------------------------

501bbag -----------------------

REMOVER, PAINT: alkali-organic solvent, nonflammable, liquid, 50 gal ina 55 galagitatordr, MIL-

R-12294.

5 gal cntr ----------------------

55 ~~;a] dr ------------------------

REMOVER, PAINT: alkali (nonferrous mtl) Fed TT-R-230, class II,

400 lb dr.

REMOVER, PAINT: alkali (ferrous mtl) Fed TT-R-230, class I, 400 lb dr.

TAPE, PRESSURE SENSITIVE AD-

HESIVE : paper backing, waterresistant, natural, 120 yd roll Fed

],pp_T_76

Width, Inches

2 -------------------------

3 -------------------------

THINNER, PAINT, MINERAL

SPIRITS: 340deg Fto485deg F distillation range, Fed TT-T-291a,

34

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

(7)

Illustraticm

INDEX

Abbreviations . . . . . . . . . . . .

P a r a g r a p h s

App II

& IV

3d

P a g e

22,28

3

Accidents, report of . . . . . . . .

Administrative storage:

Army shipping documents . . .

General . . . . . . . . . . . . . . .

Inspection . . . . . . . . . . . . .

Marking . . . . . . . . . . . . . . .

Packing . . . . . . . . . . . . . . .

Preparation for shipment . . . .

Preservation and packing . . .

Responsibility (shipping). . . .

Storage procedures . . . . . . . .

Allocation, maintenance . . . . . .

Army regulations (listings)

Army shipping documents . . . . .

42b

44a

44c

43c

43 b

42c

43a

42a

44 b

2

App I

42b

17

17

17

2

20

17

17

17

18

17

17

17

Basic issue items list . . . . . . .

App II 22

Cleaning . . . . . . . . . . . . . . .

General . . . . . . . . . . . . . . .

Metal parts . . . . . . . . . . . . .

Precautions (general) . . . . .

Rust removal . . . . . . . . . . . .

Rubber parts other than electrical . . . . . . . . . . . . .

Cleaning, preserving, and packaging materiais . . . . . .

Cleaning precautions . . . . . . .

Commercial publications . . . . .

Common tools and equipment

(operator). . . . . . . . . . . . . .

Controls, instruments, and related items (general) . . . . . .

23

23a

23a(1)

23 b

23c

23a(2)

App IV

23b

App I

19

9

10

10

10

10

10

10

28

10

20

9

5

5

6

Data plate . . . . . . . . . . . . . . .

Data, tabulated . . . . . . . . . .

Demolition of materiel to prevent enemy use (general) . . . . . . .

Definition of terms, preventive maintenance . . . . . . . . .

Description and data:

Description . . . . . . . . . . . .

Data plate . . . . . . . . . . . . .

Tabulated data . . . . . . . . . .

Destruction of nozzle tester:

General . . . . . . . . . . . . . . .

Method No. 1 . . . . . . . . . . .

Method No. 2. . . . . . . . . . .

Method No. 3 . . . . . . . . . . .

Direct reporting of errors . . . . .

Discharge block assembly arid hydraulic pressure gage:

Assembly . . . . . . . . . . . . .

Cleaning . . . . . . . . . . . . .

Description . . . . . . . . . . .

Disassembly . . . . . . . . . . .

Inspection and repair . . . . .

45

22b

4

5

6

45

46a

46b

46c

1f

41f

41d

12,40

41c

41e

18

9

3

3

16

16

6,16

16

16

18

19

19

19

2

3

3

3

Maintenance (general) . . . .

Removal . . . . . . . . . . . . .

Explanation of columns . . . . . .

P a r a g r a p h s

41a

41b

App II

& IV

P a g e

16

16

22,28

Field manuals (listing) . . . . . .

Forms, records, and reports . . .

Authorized forms . . . . . . . . .

Forms (listing) . . . . . . . . .

Equipment improvement recommendations . . . . . . . .

Field report of accidents . . . .

General . . . . . . . . . . . . . . .

Fuel reservoir assembly:

Assembly . . . . . . . . . . . . . .

Cleaning .. . . . . .. . . . . . . . . . . . . .

Description . . . . . . . . . . . . .

Disassembly . . . . . . . . . . . .

Inspection and repair . . . . . .

Maintenance (general) . . . . . .

Gage, hydraulic pressure . . . . .

General cleaning precautions . .

App I

3

3b

App I

3 c

3d

3a

Hydraulic pressure gage . . . . .

Hydraulic pressure gage valve assembly . . . . . . . . . .

Inspection:

Administrative storage . . . . .

Receipt of materiel . . . . . . .

Introduction (general):

Scope . . . . . . . . . . . . . . . .

11

44 c

7a, 7b

Lubrication . . . . . . . . . . . . . .

1

8c & 21

39e

39c

10,38

39b

39d

39a

12

23b

12

20

2

3

20

Maintenance (organizational) . . .

Maintenance allocation . . . . . .

Operator . . . . . . . . . . . . . . .

Organizational , . . . . . . . . . .

Maintenance allocation chart. . .

Marking . . . . . . . . . . . . . . . .

Military publications . . . . . . . .

Mounting instructions . . . . . . .

Operation (detail) . . . . . . . . . .

Operation (general) . . . . . . . . .

Operator maintenance allocations

Operator maintenance instructions:

General . . . . . . . . . . . . . .

Purpose . . . . . . . . . . . . . .

Operator’s preventive-maintenance services . . . . . . . . .

Purpose . . . . . . . . . . . . . .

Services . . . . . . . . . . . . .

Organizational maintenance allocations . . . . . . . . . . . . .

39

2

2a

2b

App III

43c

App I

16b

16

14

2a

17

7

24

24a

24b

2b

5,9

14

2

2

2

27

17

20

6

15

15

5,14

15

15

14

6

10

3

3

2

6

5

18

5

2

10

10

10

9

5

2

6

6

2

35

Paragraphs

Organizational maintenance instructions:

Common tools and equipment

General . . . . . . . . . . . . . .

Repair parts . . . . . . . . . . .

Special tools and equipment

Organizational preventivemaintenance services:

General . . . . . . . . . . . . . .

Services . . . . . . . . . . . . .

Packing . . . . . . . . . . . . . . . .

Painting . . . . . . . . . . . . . . . .

Plates (data) . . . . . . . . . . . . .

Preparation:

Operation . . . . . . . . . . . . . .

Shipment . . . . . . . . . . . . . .

Preservation, packaging, packing, and marking instructions

Marking . . . . . . . . . . . . . .

Packing . . . . . . . . . . . . . .

Preservation and packaging

Pressure gage, hydraulic . . . . .

Prevent enemy use (destruction]:

General . . . . . . . . . . . . . . .

Method No. 1 . . . . . . . . . . .

Method No. 2 . . . . . . . . . . .

Method No. 3 . . . . . . . . . . .

Preventive-maintenance services:

Definition of terms . . . . . . .

General . . . . . . . . . . . . . .

Operator’s . . . . . . . . . . . .

Organizational . . . . . . . . .

Responsibility and intervals

Publication indexes . . . . . . . .

Publications (listing of) . . . . .

Pump handle assembly and handle shoe . . . . . . . . . . . .

Records, reports, and forms . . .

References . . . . . . . . . . . . .

Repair parts (operator). . . . . . .

Repair parts, and special tools

Repair parts, tools and equipment, operator (general) . . . .

22b

22,33

24

34

22a

App I

App I

13

3

App I

18

App IV

17

33

34

43b

32

5

15

42c

43

43c

43b

43a

12

45

46a

46b

46c

30

28

29

31

Page

13

13

13

3

9

9,13

10

13

9

20

20

6

2

20

9

28

9

6

17

7

3

3

3

3

17

17

17

17

6

18

19

19

19

Repair parts, tools and equipment, organizational (general)

Report of accidents . . . . . . . . .

Reservoir, fuel . . . . . . . . . . . .

Rust removal . . . . . . . . . . . . .

S c o p e ( i n t r o d u c t i o n ) . . . . .

Services . . . . . . . . . . . . . . . .

Cleaning . . . . . . . . . . . . . .

Inspection . . . . . . . . . . . . .

Lubrication . . . . . . . . . . . . .

Unpacking and checking . . . .

Service upon receipt of materiel (purpose) . . . . . . . .

Shipping instructions . . . . . .

Responsibility. . . . . . . . . . .

Army shipping documents . . . .

Preparation for shipment . . . .

Source, maintenance and recoverability code . . . . . .

Special tools and equipment . . ,

Specifications (military). . . .

Storage procedures . . . . . . . . .

T a b l e s :

Preventive maintenance checks and services

(table I) . . . . . . . . . . . . . .

Troubleshooting (operator’s)

(table II) . . . . . . . . . . . . .

Troubleshooting (organiza-

tional) (table III) . . . . . .

tabulated data . . . . . . . . . . .

Testing nozzles . . . . . . . . . . .

General . . . . . . . . . . . . . . .

Opening pressure . . . . . . . . .

Spray pattern . . . . . . . . . . . .

Chatter . . . . . . . . . . . . . . .

Leakage . . . . . . . . . . . . . . .

Troubleshooting (1st echelon):

Procedure . . . . . . . . . . . . .

Purpose . . . . . . . . . . . . . . .

Scope . . . . . . . . . . . . . . . .

Troubleshooting (2nd echelon): procedure . . . . . . . . . . . . . .

Purpose . . . . . . . . . . . . . . .

Scope . . . . . . . . . . . . . . . .

Paragraphs

24

27

37

6

16c

16c(1)

16c(2)

16c(3)

16c(4)

16c(5)

28

3d

10

23c

1

8

8b

8d

8

C

8a

7

42

42a

42b

42c

App II

& IV

20

App I

44b

37

35

36

27

25

26

Page

5

17

17

17

17

22,28

9

20

17

14

13

14

13

3

5

10

5

5

5

5

2

5

10

12

12

11

11

8

8

8

8

14

3

6

6

36

By Order of Secretary of the Army:

Official:

J. C. LAMBERT,

Major General, United States Arrny,

The Adjutant General.

Distribution:

DCSLOG (1)

CNGB (1)

CofEngrs (6)

CofSptS (2)

CofT (1)

CSigO (1)

TSG (1)

USAMC (12)

USASMCOM (6)

USAWECOM (64)

USCONARC (3)

ARADCOM (2)

ARADCOM Rgn (2)

OS Maj Cored (1)

OS Base Cored (2)

LOGCOMD (3)

USACOMZEUR (1)

Armies (3) except

Seventh (5)

EUSA (5)

Corps (2)

USA Corps (2)

Ft Monmouth (8)

Ft Belvoir (2)

Army Dep (2) except

Lexington (1)

Letterkenny (11)

NG: State AG (3).

USAR: N o n e .

For explanation of abbreviations used, see AR 320-50.

EARLE G. WHEELER,

G e n e r a l , U n i t e d S t a t e s A r m y ,

Chief of Staff.

Arsenals (1) except

Detroit (5)

USA Avn & Sur Mat Cored (1)

APG (1)

Brooklyn Army Terminal

Units org fol TOE (2 cy ea):

6-635

7-17

7-37

9-7

9-25

9-26

9-27

9-65

9-67

9-127

9-197

9-217

9-357

10-105

10-107

10-445

10-448

10-500 (Tins HK)

17

29-51

29-56

57

37

This fine document...

Was brought to you by me:

Liberated Manuals -- free army and government manuals

Why do I do it? I am tired of sleazy CD-ROM sellers, who take publicly available information, slap “watermarks” and other junk on it, and sell it.

Those masters of search engine manipulation make sure that their sites that sell free information, come up first in search engines. They did not create it...

They did not even scan it... Why should they get your money? Why are not letting you give those free manuals to your friends?

I am setting this document FREE. This document was made by the US

Government and is NOT protected by Copyright. Feel free to share, republish, sell and so on.

I am not asking you for donations, fees or handouts. If you can, please provide a link to liberatedmanuals.com, so that free manuals come up first in search engines:

<A HREF= http://www.liberatedmanuals.com/ >Free Military and Government Manuals</A>

– Sincerely

Igor Chudov http://igor.chudov.com/

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement