Craftsman | 315.115410 | Operator`s manual | Craftsman 315.115410 Operator`s manual

OPERATOR'S
MANUAL
1/2 in., 19.2 VOLT CORDLESS DRILL-DRIVER
VARIABLE SPEED/REVERSIBLE
Model No.
315.115410
_,
WARNING:
To reduce the risk of injury,
the user must read and understand the
operator's manual before using this
product.
Customer
Help Line: 1-800-932-3188
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman
Visit the Craftsman web page: www.sears.com/craftsman
983000-716
5-05
Estates,
Save this manual for future
IL 60179 USA
reference
0( )us
• Warranty ...........................................................................................................................................................................
2
• Introduction ...................................................................................................................................................................... 2
• General Safety Rules ..................................................................................................................................................... 3-4
• Specific Safety Rules ....................................................................................................................................................... 4
• Safety Rules for Charger ................................................................................................................................................. 5
• Symbols ......................................................................................................................................................................... 6-7
• Features ........................................................................................................................................................................ 8-9
• Assembly .......................................................................................................................................................................... 9
• Operation ................................................................................................................................................................... 10-15
•
Maintenance .............................................................................................................................................................. 16-17
•
Exploded View and Parts List ......................................................................................................................................... 18
•
Parts Ordering / Service .................................................................................................................................... Back Page
ONE YEAR FULL WARRANTY ON CRAFTSMAN TOOL
ff this Craftsmantool fails to give complete satisfactionwithin one year from date of purchase,RETURN IT TO THE
NEAREST SEARS STORE OR SEARS PARTS& REPAIR CENTER IN THE UNITED STATES, and Sears will repairit,
free of charge.
If this Craftsman tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date of
purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability have
been given top priority in the design of this product making it easy to maintain and operate.
_
WARNING]
• Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
• Avoid accidental starting. Ensure the switch is in
the off-position before plugging in. Carrying power
tools with your finger on the switch or pluggingin
power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning
the power tool on. A wrenchor a key leftattached to
a rotatingpart of the power tool may resultin personal
injury.
• Do not overreach. Keep proper footing and balance
at all times. This enables better controlof the power
tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from
moving parts, Looseclothes,jewe}ry,or long hair can
be caught in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used, Use of these devices
can reduce dust-related hazards.
Read all instructions. Failure to follow
all instructions listed below may result in electric
shock, fire and/or serious injury. The term "power
tool" in all of the warnings listed below refers to your
mains-operated (corded) power tool or battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not operate power tools in.explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignitethe dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractionscan causeyou to lose
control.
ELECTRICAL
SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
• Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
• Avoid body contact with earthed or groundedsurfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a powertool will increasethe risk
of electricshock.
• Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better controlof the
power tool in unexpectedsituations.
POWER TOOL USE AND CARE
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool, Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• Use battery only with charger listed.
MODEL
BATTERY PACK
CHARGER
315.115410
130279003
Model No. 1425301
130279005
(Item No. _911041)
(Item No. 911375) Model No. 315.115730
(Item No. 140301003)
Model No, 315.115720
(Item No. 140301001)
PERSONAL SAFETY"
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattentionwhile operating power tools may
result in serious personal injury.
3
• Do not force the power tool. Use the correct power
tool for your application. The correctpower tool will
do the job better and safer at the rate for which it was
designed.
• Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventivesafety measures reduce
the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power toolsare dangerous in the hands of untrained
users.
• Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts, and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidentsare caused by poorly
maintained power tools.
• Keep cutting tools sharp and clean, Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
•
Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended could
result in a hazardous situation.
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
•
BATTERY TOOL USE AND CARE
•
Ensure the switch is in the off position before inserting battery pack. Inserting the battery pack into
power tools that have the switch on invitesaccidents.
SERVICE
• Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
• Recharge only with the charger specified by the
manufacturer. A chargerthat is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
• When servicing a power tool, use only identical
replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance instructions may
create a risk of shock or injury.
• Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
• When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
WARNING! To reduce the risk of nnlury,user must
read instruction manual.
• Use auxiliary handles supplied with the tool. Lossof
control can cause personal injury.
• Do not place battery tools or their batteries near
fire or heat. This will reducethe risk of explosion and
possiblyinjury.
• Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring. Contact with a "live" wire will
also make exposed metal parts of the tool "live" and
shock the operator.
•
Under abusive conditions, liquid may be ejected
from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquidejected
from the battery may cause irritationor burns.
• Never use a battery that has been dropped or
received a sharp blow. A damaged battery is subject
to explosion. Properlydispose of a dropped or
damaged batteryimmediately.
• Batteries vent hydrogen gas and can explode in
the presence of a source of ignition, such as a pilot
light. To reducethe risk of seriouspersonal injury,
never use any cordless product in the presence of
open flame. An exploded battery can propel debris and
chemicals. If exposed, flush with water immediately.
• Do not charge battery tool in a damp or wet
location. Followingthis rule will reducethe risk of
electric shock.
Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
• Always wear safety glasses with side shields.
Everydayglasses haveonly impact resistant lenses.
They are NOT safety glasses. Following this rule will
reduce the risk of eye injury.
For best results, your battery tool should be
charged in a location where the temperature is
more than 5O°Fbut less than 100°F. Do not store
outside or in vehicles.
•
Protect your lungs, Wear a face or dust mask if the
operation is dusty. Followingthis rule will reducethe
risk of serious personal injury.
• Protect your hearing. Wear hearing protection
during extended periods of operation. Following this
rule will reduce the risk of serious personal injury.
• Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories. Following this rule will reduce the risk of
electricshock, fire, or seriouspersonal injury.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Followingthis rule will
reduce the risk of serious personal injury.
4
_
WARNING! READ AND UNDERSTAND ALL
INSTRUCTIONS, Failure to follow all instructions
listed below, may result in electric shock, fire
and/or serious personal injury.
• Before using battery charger, read all instructions
and cautionarymarkings in this manual, on battery
charger, battery, and product usingbattery to prevent
misuse of the productsand possible injuryor damage.
CAUTION: To reducethe risk of electric shock
or damage to the charger and battery, charge
only nickel-cadmiumrechargeable batteriesas
specifically designated on your charger. Other
types of batteries may burst, causing personal
injury or damage.
• An extension cord should not be used unless
absolutely necessary. Use of improper extension cord
could resultir_a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet)
25'
50'
100'
Cord Size (AWG)
16
16
16
NOTE=AWG = American Wire Gauge
• Do not use charger outdoors or expose to wet or
damp conditions. Water entering charger will increase
the risk of electric shock.
• Do not operate charger with a damaged cord or
plug, which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
serviceman.
• Use of an attachment not recommended or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
Followingthis rulewill reduce the risk of electric shock,
fire, or serious personalinjury.
• Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way. Take it to an authorized serviceman for electrical
check to determine if the charger is in good working
order.
• Do not abuse cord or charger. Never usethe cord to
carry the charger.Do not pull the charger cord rather
than the plug when disconnectingfrom receptacle.
Damage to the cord or charger couid occur and create
an electricshock hazard. Replace damaged cords
immediately.
• Make sure cord is located so that it will not
be stepped on, tripped over, come in contact
with sharp edges or moving parts or otherwise
subjected to damage or stress. This will reduce the
risk of accidental falls, which could cause injury,and
damage to the cord, which could result in electric
shock.
• Do not disassemble charger. Take it to an authorized
serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
• Keep cord and charger from heat to prevent
damage to housing or internal parts.
• Do not let gasoline, oils, petroleum-based products,
etc. come in contact with plastic parts. They contain
chemicalsthat can damage, weaken, or destroy plastic.
,_
• Unplug charger from outlet before attempting any
maintenance or cleaning to reduce the risk of
electric shock.
• Disconnect charger from the power supply when
not in use. This will reduce the risk of electricshock
or damage to the charger if metal items should fall into
the opening. It also will help prevent damage to the
charger during a power surge.
• Risk of electric shock, Do not touch uninsulated
portion of output connector or uninsulated battery
terminal.
• Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also to prevent misuse of the product and
possible injury.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm.Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
Someofthefollowingsymbolsmaybeusedonthistool.Pleasestudythemandlearntheirmeaning.
Proper
interpretation
ofthesesymbols
willallowyoutooperatethetoolbetterandsafer.
SYMBOL
NAME
DESIG NATIO N/EXP LANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
W
Watt
Power
Minutes
Time
Alternating Current
Type of current
----=-
Direct Current
Type or a characteristic of current
no
No Load Speed
Rotational speed, at no load
[]
Class II Construction
Double-insulated construction
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
Wet Conditions Alert
Do not expose to rain or use in damp locations.
Read The Operator's Manual
operator's
manual
before
using
product.
To reduce the
risk of
injury,
userthis
must
read and understand
Eye Protection
Always
goggles
safety
glassesthis
withproduct.
side
shields wear
and asafety
full face
shield or
when
operating
Safety Alert
Precautions that involve your safety.
No Hands Symbol
serious
personal
injury.
Failure to
keep your
hands away from the blade will result in
No Hands Symbol
serious
personal
injury.
Failure to
keep your
hands away from the blade will result in
_)
No Hands Symbol
Failure to
keep your
hands away from the blade will result in
serious
personal
injury.
/_
No Hands Symbol
Failure to
keep your
hands away from the blade will result in
serious
personal
injury.
(_
Hot Surface
To
the risk of injury or damage, avoid contact with
anyreduce
hot surface.
min
.../min
,_,
6
Thefollowing
signalwordsandmeanings
areintended
toexplain
thelevelsofriskassociated
withthis
product.
SYMBOL
SIGNAL
MEANING
_i,
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
,_
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION:
Indicatesa potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
CAUTION:
(Without Safety Alert Symbol) Indicatesa situation that may result in
property damage.
SERVICE
_i,
attempt to use this product until you read thoroughly
and understand completely the operator's manual.
Save this operator's manual and review frequently for
continuing safe operation and instructing others who
may use this product.
Servicing requires extreme care and knowledge
and should be performed only by a qualified service
technician. For service we suggest you return the product
to your nearest AUTHORIZED SERVICE OENTER for
repair. When servicing, use only identical replacement
parts.
_i,
WARNING: To avoid serious personal injury, do not
WARNING:
O
The operation of any power tool can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear safety
goggles or safety glasses with side shields and a full face shield when needed. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side
shields. Always use eye protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
PRODUCT SPECIFICATIONS
Chuck ........................................................... 1/2 in. Keyless
Clutch ................................................................ 24 Position
Motor ............................................................... 19.2 Volt DC
Torque.................................................. Maximum 420 inJb.
Switch .......................................................... Variable Speed
Charger Input ................................... 120 V, 60 Hz, AC only
Gear Train ............................................................... 2 Speed
Charge Rate .............................................................. 1 hour
No Load Speed .................................... 0-400/0-1,400/min.
REARVIEW
TWO-SPEED
GEARTRAIN(HI-LO)
LEVEL
TORQUE
ADJUSTMENT
RING
KEYLESS
CHUCK
AUXILIARY
HANDLEASSEMBLY
IIRECTION
OFROTATION
SELECTOR
(FORWARD]REVERSE/CENTER
LOCK)
TRIGGER
SCREWDRIVER
BIT
LED
BA'n'ERY
\
CHARGER
\
4-1/2 in,
Fig. 1
8
KNOW YOUR DRILL-DRIVER
See Figure 1.
LED WORKLIGHT
Beforeattempting to use this product, familiarize yourself
with all operating features and safety rules.
The LED worklight,located on the front of the tool base,
illuminates when the switch trigger is depressed. This
provides extra light for increased visibility.
AUXILIARY HANDLE
LEVELS
Yourdrillis equipped with an auxiliaryhandle for ease of
operation and to preventloss of control.
Levels are located on the top and end of the motor
housingto help keep the drill bit level during use.
BIT STORAGE
"I3NO-SPEED GEAR TRAIN
Bits providedwith the drill-driver can be placed in the
storagearea, located on the base of the drill.
The two-speed gear train is designed for drilling or driving
at LO (1) or HI (2) speeds. A slide switch is located on top
of your drill for selecting either LO (1) or HI (2) speed.
DIRECTION OF ROTATION SELECTOR
FORWARD/REVERSE/CENTER LOCK
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
with increased trigger pressure and lower speed with
decreased trigger pressure.
Yourdrillhas a directionof rotation (forward/reverse)
selector locatedabove the switchtrigger for changingthe
direction of bit rotation.Setting the switch trigger in the
OFF (center lock) positionhelps reducethe possibility of
accidental star_ingwhen not in use.
KEYLESS CHUCK
The keyless chuck allows you to hand-tightenor release
the drill bit in the chuck jaws.
UNPACKING
&
This product has been shipped completely assembled.
•
Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list
are included.
•
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
•
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool.
•
tf any parts are damaged or missing, please call
1-800-932-3188 for assistance.
WARNING: If any parts are missing do not operate
this tool until the missing parts are replaced. Failure
to do so could result in possible serious personal
injury.
A
_,
&
PACKING LIST
1/2 in. Drill with Auxiliary Handle (Item No. 11541)
Double-ended Bit (2)
1 Hour Charger
Battery Pack (2)
Operator's Manual
9
WARNING: Do not attempt to modify this tool
or create accessories not recommended for use
with this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING: To prevent accidental starting that
could cause serious personal injury,always remove
the battery pack from the tool when assembling
parts.
_,
CHARGING
WARNING: Do not allow familiarity with tools to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
If battery pack is below normal temperature range, the
green LED on charger wiMcome on. Allow battery pack to
reach normal temperature, then the red LED will come on.
injury.
_i,
WARNING: Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
_I,
NOTE: If the charger does not charge the battery pack
under normal circumstances, return both the battery pack
and charger to your nearest Sears Repair Center for
electrical check.
• Charge the battery pack only with the charger provided.
• Make sure the power supply is normal household
voltage, 120 volts, 60 Hz, AC only.
WARNING: Do not use any attachments or
accessories not recommended by the manufacturer
of this too[. The use of attachments or accessories
not recommended can result in serious personal
injury.
• Connect the charger to the power supply.
• Place the battery pack in the charger aligning raised rib
on the battery pack with the groove in the charger. See
Figure 2.
• Press down on the battery pack to be sure contacts on
the battery pack engage properly with contacts in the
charger.
APPLICATIONS
You may use this tool for the following purposes:
• Normally the red LED on charger will come on. This
indicates the charger is in fast charging mode.
•
Drilling in wood
•
Drilling in ceramics, plastics, fiberglass, and laminates
•
Drilling in metals
•
Mixing paint
• Red LED should remain on for approximately 1 hour
then the green LED will come on. Green LED on
indicates battery pack is fully charged and charger is
in maintenance charge mode.
CAUTION: If at any point during the charging
process none of the LEDs are lit, remove the battery
pack from the charger to avoid damaging the
product. DO NOT insert another battery. Return the
charger and battery to your nearest service center
for service or replacement.
NOTE: The green LED will remain on until the battery
pack is removed from the charger or charger is
disconnected from the power supply.
• If both yellow and green LEDs come on, this indicates
a deeply discharged or defective battery pack. Allow
the battery pack to remain in the charger for 15 to 30
minutes. When the battery pack reaches normal
voltage range, the red LED should come on. If the red
LED does not come on after 30 minutes, this may
indicate a defective battery pack and should be
replaced.
LED FUNCTIONS OF CHARGER
LED WILL BE ON TO INDICATE
CHARGER AND BATTERY PACK:
STATUS
OF
• After normal usage, a minimum of 1 hour of charging
time is required to fully recharge battery pack.
• Red LED on = Fast charging mode.
• Green LED on = Fully charged and in maintenance
charge mode.
• The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
• Green LED on = When battery pack is inserted into
charger, indicates hot battery pack or that battery pack
is out of normal temperature range.
• Do not place the charger and battery pack in an area
of extreme heat or cold, They will work best at normal
room temperature.
• Yellow and Green LEDs on = Deeply discharged or
defective battery pack.
NOTE=The charger and battery pack should be placed
in a location where the temperature is more than 5O°F
but less than 10O°F.
• No LED on = Defective charger or battery pack.
CHARGING
A COOL BATTERY PACK
THE BATTERY PACK
• When batteries become fully charged, unplug the
charger from power supply and remove the battery
pack.
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until the green LED on the front of the
charger comes on.
NOTE: Batteries will not reach full charge the first time
they are charged. Allow several cycles (operation followed
by recharging) for them to become fully charged.
10
CHARGING
A HOT BATTERY PACK
TO INSTALL BATTERY PACK
See Figure3.
When using the tool continuously, the batteries in the
battery pack will become hot. You should let a hot battery
pack cool down for approximately 30 minutes before
attempting to recharge. When the battery pack becomes
discharged and is hot, this will cause the green LED to
come on instead of the red LED. After 30 minutes, reinsert
the battery pack in the charger. If the green LED continues
to remain on, return battery pack to your nearest Sears
Repair Center for checking or replacing.
• Lock switch trigger on the drill by placing the direction
of rotation selector in center position.
• Place battery pack in the drill. Align raised rib on
battery pack with groove inside drill.
• Make sure the latches on each side of your battery
pack snap in place and battery pack is secured in drill
before beginning operation.
CAUTION: When placing battery pack in the drill,
be sure raised rib on battery pack aligns with groove
inside drill and latches snap into place properly.
Improper assembly of battery pack can cause damage
to internal components.
NOTE: This situation only occurs when continuous use of
the tool causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "Charging
a Cool Battery Pack" for normal recharging of batteries.
If the charger does not charge your battery pack under
normal circumstances, return both the battery pack and
charger to your nearest Sears Repair Center for electrical
check.
TO REMOVE BATTERY PACK
See Figure3.
• Lock switch trigger on the drill by placing the direction
of rotation selector in center position.
BATTERY
PACK
SHOWNIN CHARGER
• Locate latches on side of battery pack and depress to
release battery pack from the drill.
• Remove battery pack from the drill.
CHARGER
REDLED
iREEN
BATTERY
PACK
LATCHES
LED
Fig. 2
DEPRESS
LATCHES
TO
RELEASE
BATTERY
PACK
11
Fig. 3
_k
WARNING:
Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
DIRECTION
OFROTATION
SELECTOR
(FORWARD/REVERSE/
CENTER
LOCK
REVERSE
To stop the drill, release the switch trigger and allow the
chuck to come to a complete stop.
NOTE: The drill will not run unless the direction of rotation
selector is pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage may
cause the drill to become overheated. If this occurs, cool
the drill by running it without a load and at full speed,
TWO-SPEED
See Figure 5.
GEAR TRAIN
The drill has a two-speed gear train designed for drilling or
driving at LO (1) or HI (2) speeds.A slide switch is located
on top of the drill to select eitherLO (1) or HI (2) speed.
When usingdrillin the LO (1) speed range, speed will
decrease and unitwill have more powerand torque. When
usingdrillin the HI (2) speed range, speed will increase
and unitwill have lesspower and torque. Use LO (1)
speed for high power and torque applicationsand HI (2)
speed for fast drilling or driving applications.
SWITCH
TRIGGER
FORWARD
Fig. 4
SWITCH TRIGGER
See Figure4.
TWO-SPEED
GEARTRAIN(HI-LO)
To turn the drill ON, depress the switchtrigger.To turn it
OFF, release the switch trigger,
LO
_SPEED
VARIABLE SPEED
See Figure 4.
SPEED
The variable speed switch delivers higher speed and
torque with increasedtrigger pressure and lowerspeed
with decreased triggerpressure.
NOTE: You might hear a whistlingor ringing noise from
the switch during use. Do not be concerned; this isa
normal part of the switch function.
FORWARD/REVERSE/CENTER
LOCK
See Figure4.
The direction of bit rotation is reversibleand is controlled
by a selectorlocated above the switch trigger. With the
drill held in normal operating position,the direction of
rotation selector should be positionedto the left of the
switch triggerfor drilling.The drillingdirection is reversed
when the selector is to the rightof the switch trigger.
Fig. 5
Setting the switch trigger in the OFF (center lock) position
helpsreducethe possibility of accidental starting when not
in use.
CAUTION: To prevent gear damage, always allow
the chuck to come to a complete stop before
changing the direction of rotation.
12
KEYLESS CHUCK
TODECREASE
TORQUE
See Figure 6.
The drillhas a keylesschuck to tighten or release drill
bits in the chuck jaws. The arrows on the chuck indicate
which directionto rotate the chuck body in order to LOCK
(tighten)or UNLOCK (release)the drill bit.
_I,
WARNING:
4_
ADJUSTINGRING
Do not hold chuck bodywith one hand
and use power of the drillto tighten chuck jaws on
drillbit. Chuck body could slip in your hand or your
hand could slipand come in contact with rotating
drillbit. Thiscould cause an accident resulting in
serious personalinjury.
DRILLBIT
UNLOCK
(RELEASE)
TOINCREASE
TORQUE
CHUCK
BODY
Fig. 7
LED WORKLIGHT
See Figure 8.
The LED worklighton the foot of the drill will come on
when the switch trigger is depressed. This provides
additional lighting on the surface of the workpiece for
operation in lower-light areas.
CHUCK
JAWS
LOCK
(TIGHTEN)
Fig. 6
ADJUSTABLE TORQUE CLUTCH
This product is equipped with an adjustable torque
clutchfor drivingdifferenttypes of screws intodifferent
materials.The proper setting depends on the type of
materialand the size of screw you are using.
LED
WORKLIGRT
TO ADJUST TORQUE
See Figure 7.
• There are twenty-four torque indicator settings located
on the front of the drill.
• Rotate the adjusting ring to the desired setting.
•
1-4
For driving small screws
•
5-8
For driving screws into soft material
•
9 - 12
For driving screws into soft and hard
materials
•
13 - 16 For driving screws into hard wood
•
17 - 23 For driving large screws
•
411
Fi 8
For heavy drilling
13
BIT STORAGE
See Figure 9.
UNLOCK
(RELEASE)
DRILLBIT
CHUCK
COLLAR
When not in use, bits provided with the drill can be placed
in the storage area located on the base of the drill.
SCREWDRIVER
BIT
CHUCK
JAWS
LOCK
(TIGHTEN) CHUCK
BODY
STORAGE
AREA
RIGHT
Fig. 10
Fig. 9
INSTALLING BITS
See Figures I0.11.
• Lock the switch triggerby placing the direction of
rotationselectorin the center position.
• Open or close the chuck jaws to a point where the
opening is slightlylargerthan the bit size you intendto
use. Also, raise the front of the drill slightlyto keep the
bit from falling out of the chuck jaws.
• Insert the drill bit.
• Tightenthe chuck jaws on the drill bit.
_i,
WARNING:
Do not insertdrill bit intochuck jaws
and tighten as shown in figure 11. This could cause
drillbit to be thrown from drill resultingin possible
seriouspersonal injuryor damage to the chuck.
Fig. 11
REMOVING BITS
• Rotate the chuck clockwise to tighten the chuck jaws
securely on the bit.
See Figure 10.
•
NOTE: Rotate the chuck body in the direction of the
arrow marked LOCK to tighten the chuck jaws. Do not
use a wrench to tighten or loosen the chuck jaws.
Lock the switchtrigger by placingthe directionof
rotation selector in the center position.
• Rotate the chuck sleeve clockwiseto open the chuck
jaws.
NOTE: Rotate the chuck body in the directionof the
arrow marked UNLOCK to loosenthe chuck jaws. Do
not use a wrench to tighten or loosenthe chuck jaws.
• Remove the drill bit.
14
ADJUSTING
THE AUXILIARY HANDLE ASSEMBLY
LEVEL
See Figure 12.
•
Loosenthe auxiliaryhandle assembly by turningthe
knobcounterclockwise.
•
Rotate the auxiliaryhandle assemblyto the desired
location.
•
Tighten the auxiliaryhandle assemblysecurelyby
turningthe knobclockwise.
AUXILIARY
TORQUE
HANDLEASSEMBLYADJUSTMENT
RING
Fig. 13
• When drilling hard, smoothsurfaces, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off-center as the hole
is started.
36oo___ j
ROTATION
• When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil will prolong the life of
the bit and increase the drilling action.
Fig. 12
DRILLING
• If the bit jams in the workpiece or if the drill stalls,
stop the tool immediately. Remove the bit from the
workpiece and determine the reason for jamming.
NOTE; This drill has an electric brake. When the switch
trigger is released, the chuck stops turning. When the
brake is functioning properly, sparks will be visible through
the vent slots on the housing. This is normal and is the
action of the brake.
See Figures 13 - 14.
Levels are located on the top and end of the motor
housing to help keep the drill bit level during use,
• Check the direction of rotation selectorfor the correct
setting (forward or reverse).
• Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
• Hold the drill firmly and place the bit at the point to be
drilled.
• Depress the switch trigger to start the drill.
• Move the drill bit into the workpiece, applying only
enough pressure to keep the bit cutting. Do not force
the drill or apply side pressure to elongate a hole. Let
the tool do the work.
,_
WARNING: Be prepared for binding at bit
breakthrough. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material. If not prepared, this loss
of control can result in possible serious injury.
Fig. 14
15
_lb
MALLET
WARNING: When servicing, use only identical
Craftsman replacement parts. Use of any other part
may create a hazard or cause product damage.
CHUCKJAWS
WARNING: Always wear safety goggles or safety
glasses with side shields when usingcompressed air
to clean tools. If the operationis dusty, also wear a
dust mask.
_k
WARNING: To avoid serious personal injury,always
remove the battery pack from the toolwhen cleaning
or performingany maintenance.
HEXKEY
CHUCK
GENERAL MAINTENANCE
Fig. 15
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
_1= WARNING:
• Open the chuck jaws and remove the hex key. Using a
screwdriver, removethe chuck screw by turning it in a
clockwisedirection.
NOTE: The chuck screw has left hand threads.
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc., come in contact with plastic parts.
Chemicals can damage, weaken or destroy plastic
which may result in serious personal injury.
Only the parts shown on the parts list are intendedto be
repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
SCREWDRIVER
CHUCK REMOVAL
See Figures 15 - 17.
The chuck may be removed and replaced by a new one.
• Lock the switch trigger by placing the direction of
rotation selector in center position.
Fig. 16
• Insert a 5/16 in. or larger hex key into the chuck of the
drill and tighten the chuck jaws securely.
B Tap the hex key sharply with a mallet in a clockwise
direction. This will loosen the screw in the chuck for
easy removal.
16
•
Insert the hex key into the chuck and tighten the
chuck jaws securely. Tap sharply with a mallet in a
counterclockwise direction. This will loosen the chuck
on the spindle. It can now be unscrewed by hand.
TO RETIGHTEN A LOOSE CHUCK
The chuck may become loose on the spindle and develop
a wobble. Also, the chuck screw may become loose,
causing the chuck jaws to bind and prevent them from
closing. To tighten:
•
Lock the switch trigger by placing the direction of
rotation selector in the center position.
• Open the chuck jaws.
•
LLET
Insert the hex key into the chuck and tighten the chuck
jaws securely. Tap the hex key sharply with a mallet in
a clockwise direction. This will tighten the chuck on the
spindle.
• Open the chuck jaws and remove the hex key.
• Tighten the chuck screw.
Fig. 17
BATTERIES
BATTERY PACK REMOVAL
FOR RECYCLING
The battery pack for this tool is equipped with nickelcadmium rechargeable batteries. Length of service from
each charging will depend on the type of work you are
doing.
AND PREPARATION
To preserve natural resources, please
recycle or dispose of batteries
properly.
This product contains nickel-cadmium
batteries. Local, state or federal
laws may prohibit disposal of nickelcadmium batteries in ordinary trash.
The batteries in this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in a serious burn.
Consult your I(_calwaste authority for information
regarding available recycling and/or disposal options.
To obtain the longest possible battery life, we suggest the
following:
_i,
•
WARNING: Upon removal, cover the battery pack's
terminals with heavy-duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
Remove the battery pack from the charger once it is
fully charged and ready for use.
For battery pack storage longer than 30 days:
• Store the battery pack where the temperature is below
8O°F.
• Store battery packs in a "discharged" condition.
17
CRAFTSMAN
19.2 VOLT CORDLESS DRILL-DRIVER
MODEL NO. 315.115410
(Item No. 11541)
•
J
The
model
number
will be found
on a plate
to the
motor housing.
Alwaysordering
mentionrepair
the model
number
in all
correspondence
regarding
your attached
CORDLESS
DRILL-DRIVER
or when
parts. ]
SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS
4
6
PARTS LIST
Key
No.
PaN
Number
Description
1
6613402
Screw (Special).................................................................................... 1
2
940055109
Data Plate............................................................................................ 1
3
690033066
Chuck ................................................................................................ 1
4
300188028
Auxiliary Handle Assembly .................................................................. 1
5
130279003 or
130279005
*Battery Pack (Item No. 9 11375) ......................................................... 2
1425301
* Charger (Item No. -911041) ................................................................. 1
983000716
Qty.
Operator's Manual
* Can Be Purchased Thru RSOS (Retail Special Order System)
m
i
18
Get it fixed, at your home or ours!
Your Home
For repair-in
your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
Call anytime,
® (1-800.469-4663)
day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime,
day or night (U.S.A. only)
v_vw.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced
1-800-827-6655
1-800-361-6665
(U.S.A.)
Para pedlr serv_cio de reparacl0n
a dom_cllio, y para ordenar piezas:
1-888"SU-HOGAR
Au Canada
by Sears:
(Canada)
pour service en fran(2als:
1-800-LE-FOYER
sM
Mc
(1-800-533-6937)
www.sears ca
(1-888-784-6427)
Sesirs
=.._..,,,,-,_=,_=_=_
® Regrstered Trademark / TVTrademark t su Service Mark of Sears, Roebuck and Co
® Marca Reglstrada / "PuMarca de Fabnca / SMMarca de ServlcLo de Sears, Roebuck and CO
MCMarque de commerce / MDMarque deposee de Sears, Roebuck and Co
© Sears, Roebuck and Co
960026104-01{Aj
Download PDF

advertising