Manual 19212648

Manual 19212648
OPERATING INSTRUCTIONS
3 BUTTON TRANSMITTER
MUTE
FUNCTION | ARM [DISARM| ALARM | |ANTI-HUACKING| panic TRUNK POWER
MODE RELEASE | WINDOW
When ACC-ON
Press E For
E | @
Seconds seconds disarming mode
4 BUTTON TRANSMITTER
MUTE т. -
FUNCTION | ARM |DISARM| ALARM [|ANTI-HUACKING| panic UNK POWER
MODE RELEASE | WINDOW
When e Press rn F
press then or
Ress | @ | of QX | press A vittin | M/EN |3 Secondrin 8
$ seconds. disarming mode
FUNCTION SETTING
FUNCTION JP Position METHOD
Electronic / Pi Electronic Lock: Short circuit
Air Compressor Lock Air compressor Lock: Open circuit
NOTE:
1, THE SYSTEM IS SET IN JP1 SHORT CIRCUIT (ELECTRONIC LOCK) MODE
DURING PRODUCTION.
2. ICON OF INDICATING SHORT CIRCUIT & OPEN CIRCUIT. { : <<SHORT)
(: <<OPEN)
4. DO JP SETTING IN NO POWER SUPPLIED CONDITION.
A) ARM THE ALARM
(a) Siren will chirp once and lights flash once.
(b) If equipped with central door lock, doors lock automatically.
(c) The power window will close up automatically.
(d) Alarm is armed, the L.E.D blinks.
B) DISARM THE ALARM
(a) Siren will chirp twice and lights flash 3 times.
(b) Power door lock/unlock automatically.
(c) Alarm is disarmed and returns to its normal status.
(d) If nobody enters into the car within 20+ § seconds, the system will be re-armed automatically.
Please also refer to “ AUTO REARMING” feature.
C) MUTE ALARM MODE
(a) Lights flash once, but siren will not chirp.
(b) Ifequipped with central door lock, power window, doors lock automatically, power window will close up
automatically. The system is armed and LED blinks.
(c) If the alarm shock is triggered, lights will flash, but siren will not sound.
(d) If the door is opened, the alarm will be activated after 15 seconds.
D) CAR FINDING
(a) Press M/É in normal arming mode, the siren will sound and lights will flash for 15 seconds. Engine will
be cut-off. Press A / A to stop.
@
(b) After the15 seconds alarm cycle, the system will return to its previous status (arming or mute alarm
mode).
(c) This feature can be used as a searching function to locate the vehicle in a large parking lot.
E) STOP SIREN TEMPORARILY
If alarm system is triggered off, the siren will blare. By pressing [email protected] to stop the siren temporarily but
the alarm system is still in arming mode.
F) CALL FOR EMERGENCY HELP/CLEARING THE WAY
When ACC ON, press Af/ [\ , the siren will keep sounding and parking lights will keep flashing for 15
seconds to calling for emergency help. Press A/ £A) to stop the above operation.
G) ANTI-HIJACKING
When driving, the key on ACC.ON position. Press Af/ L\, for 3 seconds, the parking lights will flash quickly
(This is stand-up for anti-hijacking mode). the system is into anti-hijacking mode, the lamps keep
lighting. And the engine will be cut off after 15 seconds and siren keeps sounding, lamps flashing. Press
a to stop the function. (for 3 button)
When driving, the key on ACC.ON position. Press M/£ | the parking lights will flash quickly (This is stand
-up for anti-hijacking mode). And then pressing button M/£ within 5 seconds, the system is into anti-
hijacking mode, the lamps keep lighting. After 15 seconds, the engine will be cut off and siren keeps
sounding, lamps flashing. Press @ to stop the function. (for 4 button)
Make the car stop automatically about 10 seconds after the robber drive the car.
Suggestion: Connect engine cut off relay to starter power wire.
1. MISS-TOUCH
Once the vehicle started accidentally touching buttons that normally arm the alarm, will not arm the alarm,
but will lock doors. Press g button to unlock the doors. |
2. AUTO RE-ARM |
If nobody enters the car in 20+/-5 seconds after the system is disarmed by pressing button aß , the door of
the car will automatically be locked again and the system will come back to be on "ALERT" mode.
3. AUTO CENTRAL LOCK
When driving, press a or & to lock or unlock the doors, but the alarm system will not be set work. Turn
on the ignition after closing the car doors in a proper way, after 15 seconds, step on the foot brake and the
car doors will be locked automatically. Please note: The doors will not be locked automatically if the ignition
key is not turned to the "ACC. ON" position or if the doors are not closed properly.
The car doors will automatically-unlock when the key is taken out of the ignition switch.
VIBRATION RECORD |
If the car is bumped, the system will take a record about the vibration of the car and will give warning to the
car owner by 4 beeps when the alarm system is disarmed, so that the car owner can check the car inside and
outside to make sure about the safety of the car.
. WARNINGS TO IMPROPER CLOSED OF DOORS /optional (original setting: Valid)
Before driving, ACC OFF if the doors are not properly closed, the lamps will keep flashing for 15 seconds
in order to give warnings to the cars behind.
Before driving, ACC ON, if the doors are not properly closed, the lamps will keep flashing until the door is
closed.
When the car is parked, open the door, the lights will keep flashing to give warning to the cars behind.
Ín disarming mode, keep pressing N / A 3 seconds, the siren will chirp twice and lights flash twice, indicating
the function is valid; the siren chirp once and lights flash once, indicating the function is invalid .
+
wh
©
6. WARNINGS OF ABNORMAL SITUATION
If the alarm system is tnggered in arming mode, then:
The siren will sound for 25£ 5 seconds in arming mode (without sounding in silent mode) when the car
window is knocked or when the car is bumped.
The siren will keep on when the car door is opened or when the engine is ignited illegally.
7. INTRUSION ALERT
If the car door is opened during the arming mode, when the owner press @ button to disarm the car,
the siren will chirp 6 times to give warning to the car owner to take caution to the theft inside the car.
8. MEMORY ALARM MODES
If the car power is cut off whether the system is armed or disarmed, the system will still keep in original
condition.
9. TRUNK RELEASE FUNCTION |
In disarming mode, press a button for 3 seconds, the trunk will be released automatically.
10. POWER WINDOW FUNCTION
Press 8 button once time, the siren will chirp once and light flash once. and the power window will
close automatically. It lasts at 25 seconds.
11. RESET FUNCTION
Open the door, step on the foot brake, turn ACC ON/OFF for 10 times, and keep ON position, the lights
will keep on. Then the system is disarmed. (It used in the remotes lost.)
12. REMOTE ENGINE START
a. When the gear is "N"or "P"_press dl + X, / A in the same time the lights keep on 1 second, siren will
chirp once, the engine is started and lasting for 15 minutes. Within 15 minutes, press Af/ LA . the siren
chirps twice to cut off the engine. But the system is still under arming mode. (for 3 buttons
transmitter only)
when the gear is "N"or "P" press (X +A / LA in the same time, the lights keep on { second, siren will
* chirp once, the engine is started and lasting for 15 minutes. Within 15 minutes, press A// LL, , the siren
chirps twice, and the engine is cut-off. The system is still under arming mode. (for 4 buttons
transmitter only)
b. Press @ and enter into the car, if the car driver turn the ACC ON or step on the footbrake within 30
seconds, the system will be started continualy, otherwise, it will be cut off. If the system is not started
successfully, the system will be re-started 3 times automatically.
Note: if the hand brake is pull off, the system will forbid the remote engine start, siren will chirp 4 times
and lights flash once to give warnings to the car owner.
Warnings: For hand shift car, when engine start, the shift must be on neutral position and pull on the
hand brake tightly, or else it is very dangerous.
13. TWO STAGE STREN VERIFICATION |
If the car body by bumped slightly, the LED keep lighting and the parking light flash and the siren will
only chirp 5 times; if the car body by bumped continuously, the siren will keep sounding for 25+/-5
seconds.
14. SOUND/MUTE ALARM (For 3 buttons transmitter only/Optional)
In arming mode, press @ button for 3 seconds, the siren will chirp once, indicating the system turns
into mute alarm, repeat the operation to make the sound alarm in valid. (Original setting: sound alarm)
15. CODE LEARNING MODE |
Under disarming mode, close the door, tum ACC ON, press RESET switch for 5 seconds, LED keeps
ON, lights keep ON, the system enter into learning code mode: press any key of the transmitter within
5 seconds, LED flash 3 times, lights flash 3 times. (Only 4 transmitter can be learnt in one main unit)
When the new code is learnt successfully, turn ACC OFF, LED turn off and lights turns off, the system
quit off the learning mode. (If new transmitter learnt, all the old transmitter are invalid for safety reason.)
Store another new code by repeating the same procedure.
@
WIRING CONNECTI ON DIAGRAM
For cars equipped with
central lock and lock
motor on driver's side
door
Yor cars equipped with
central lock bot no motor
on driver’ side,add
master motor and rod,
FIG?
For cars equipped with
central lock and à control
switch on the drivers side.
FIG3
For cars equipped with, ari
compressor controlled
central door locks. Eg
Audi, YW,Mercedes,
FIG4
(ON DOOR ON
DRIVER'S SIDE)
CENTRAL
LOCK MOTOR
(SECOND LINE)
LOCK CH
(ON DOOR ON
DRIVERS SIDE)
AIR
COMPRESSOR
TELLOW
FECEE IX Ir BLACK
JUE
Ho =
12V
WHITE BLACK | YELLOW
YELLOW
WHITE
(STANDARD TYPE)
RON Te RC
Main Unit Installation
The main unit is suggested to place under the panel. After fixing the main unit in a suitable place, start
connecting the wires in accordance to the WIRE CONNECTING DIAGRAM before putting back all the parts,
simply test the system function first.
Shock Sensor Installation
Install the sensor after fixing the main unit .It is recommended to place the shock sensor near the car doors, or
beside the panel so as to easily detect any intrusion actions. To adjust the sensitivity of the shock sensor, simply
use a screw to tum the button in the shock sensor, turning right to adjust with a higher sensitivity or vice verse.
Then test the sensitivity by triggering the shock sensor. If it triggered, the L.E.D will light up. Please do not
directly hit the shock sensor.
Central Lock Installation Guide
This system can control several common central lock types without any additional parts.
TYPE A:
For cars equipped with no central lock, recommended to install it first. (See FIG 1)
TYPE B:
For cars equipped with central lock but no motor on driver aside, add master motor and rod.
(See FIG 2). This type of installation is applicable to operate factory lock system in some FORD, Mitsubishi,
Mazda, and Nissan models.
“Installation tips: First install the actuator near the door's manual latch, and then fix the rod of the actuator
on the manual latch
TYPE C:
For cars equipped with central lock and with motor on the driver's side, (See FIG 3)
TYPE D:
The door locks are controlled by electrical activated vacuum pump. (See FIG 4). The timing of actuator
mechanism can be set as 0.7 seconds or 3 seconds on JP1 position.
For some Mercedes-Benz and Audi models.
TYPED E:
For some cars not mentioned above, please consult your dealers.
NOTE: Type B installation method (FIG 2) is suitable for most of the cars.
MAIN UNIT
Output current: signal hight SA*2, siren 10A, central lock: 10A
Coding: learning code
Voltage: 12+2V
Static Current: <15mA (except indicator, sensor)
Indicator Current : 20mA intermittently
Shock Sensor Current: <imA
Frequency: 300MHz-350 MHz
TRANSMITTER
Voltage: 12V
Current: OmA
Battery: 27A/12V
Frequency: 300MHz-350MHZ
Code: Learning code
e
The transmitter does not work.
*Check the battery level. It is suggest to replacing a new battery each year,
*Check if the transmitter 1s moistened or crash.
The transmitter does not make the main unit work.
*Check the battery level in the transmitter.
*Check 1f the transmitter is moistened or crash.
*Check 1f the frequency of the transmitter is changed.
*If possible, use another transmitter for comparison. If both of them do not work, then check the main
unit and the wire connection. (Do not open the main unit for checking) |
The central lock does not work.
*Check if the actuators are working.
*Check wire connection
*Check 1f the fuse of the main unit is damaged.
The siren does not sound when the system is triggered.
*Check if the sirens are available.
*Check the wire connection between the siren and main unit.
The siren keeps chirping while the main unit installs.
*Check if the socket is insert converse or check the wires connection or the CPU safeties fuse.
*If back up battery is used, check if the switch is positioned at ON statas
The alarm sounds 10 seconds after the vehicle is armed, same problem keeps happening again,
*Check if the shock sensor is too sensitive.
*Check if the door pin switches are damaged.
*Check wire connection,
The alarm is easily triggered when a heavy vehicle is passing through.
*Check if the shock sensor is too sensitive
OWNER'S WARRANTY RECORD
(To be completed by selling dealer)
Customer's Name:
Address:
Purchase Date:
Dealer Name:
Dealer Address:
Alarm system clde number:
Alarm system model:
Date Installed:
Note:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement