ADJ ILLUSION DOTZ 3.3 Specifications

ADJ ILLUSION DOTZ 3.3 Specifications
ILLUSION DOTZ 3.3
©2014 ADJ Products, LLC all rights reserved. Information,
specifications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsufficient and negligent assembly, installation, rigging, and operation of this product.
User Instructions
11/14
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn off all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Table of Contents
Unpacking......................................................................3
Introduction....................................................................3
Customer Support......................................................................3
Safety Precautions......................................................................4
Features.........................................................................5
Handling Precautions..................................................................6
Registration......................................................................6
Mounting.........................................................................7-8
DMX Set-Up...........................................................................9-11
System Menu............................................................................12
Operation............................................................................31-32
Kling-Net/ArtNet Control...........................................................33
DMX Traits............................................................................34-43
Photometric Chart.....................................................................44
Dimmer Curve Chart.................................................................44
Fuse Replacement....................................................................45
Cleaning..................................................................45
Trouble Shooting.......................................................................45
Warranty.........................................................................46
Specifications....................................................................47
Illusion Dotz 3.3 General Information
Unpacking: Thank you for purchasing the Illusion Dotz 3.3 by ADJ
Products, LLC. Every Illusion Dotz 3.3 has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your fixture for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without
contacting customer support first.
Introduction: The Illusion Dotz 3.3 is a DMX intelligent, moving head
fixture. The Illusion Dotz 3.3 can be a 12 channel, 14 channel, or 38
Channel DMX unit. The fixture can operate in three different operating
modes; show mode, sound-active, or under DMX control. The Illusion
Dotz 3.3 can be used as a stand alone unit or in a master/slave configuration. For best results use fog or special effects smoke to enhance
the beams projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2610
E-mail: [email protected]
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 2
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 3
Illusion Dotz 3.3 Safety Precautions
Illusion Dotz 3.3 Features
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Be sure that the local power outlet match that of the required voltage for your unit.
•Do not attempt to operate this unit if the power cord has been
frayed or broken.
•Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product outdoors voids all warranties.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 45 for cleaning details.
•Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a marked change in performance.
• 3 Modes of DMX-512 Protocol Compatible (12 DMX Channel Mode, 14 DMX Channel Mode, and 38 DMX Channel Mode)
• RDMX - Lets you set the DMX address from any DMX Controller
• 3 Operating Modes - Master/Slave; Stand Alone; Sound Active
• Kling-Net and Art-Net Compatible (Recommended control solu-
tions; Arkaos Media Master Express, Media Master Pro, and LED Master software’s (sold separately).
• Internal Microphone
• 5 Dimmer Curve Settings
• Power Cord Daisy Chaining (See below)
• Edit and Save Scenes into the Memory
• 360˚/ 540˚ Pan Movement
• 270˚ Tilt Movement
• Digital Display for Address and Function Setting
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 4
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 5
Illusion Dotz 3.3 Power Cord Daisy Chain
With this feature you can connect the fixtures to one another
using the PowerCON input and output sockets. The quantity
that can be connected is 4 fixtures maximum for 120V and 9 fixtures maximum for 240V. After the maximum fixtures has been
reached you will need to use a new power outlet. They must be
the same fixtures. DO NOT mix fixtures.
Illusion Dotz 3.3
General Instructions
To optimize the performance of this product, please read these operating
instructions carefully to familiarize yourself with the basic operations of
this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with
the unit, for future reference.
Illusion Dotz 3.3 Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
Illusion Dotz 3.3
Mounting
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualifications, do not attempt the installation yourself.
These installaiton should be checked by a skilled person once a year.
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to this unit.
Illusion Dotz 3.3 Product Registration
The Illusion Dotz 3.3 carries a two year limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight prepaid and accompany a return authorization (R.A.) number. The R.A.
number must be clearly written on the outside of the return package.
A brief description of the problem as well as the R.A. number must
also be written down on a piece of paper and included in the shipping
carton. If the unit is under warranty, you must provide a copy of your
proof of purchase invoice. You may obtain a R.A. number by contacting our customer support team on our toll free customer support
number. All packages returned to the service department not displaying a R.A. number on the outside of the package will be returned to
the shipper at the shippers cost.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 6
The Illusion Dotz 3.3 is fully operational in two different mounting
positions, hanging upside-down from a ceiling or set on a flat level
surface. To avoid internal damage to the unit, never mount the unit on
its side. Be sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.). Always use and install the supplied
safety cable as a safety measure to prevent accidental damage and/
or injury in the event the clamp fails (see next page). Never use the
carrying handles for secondary attachment.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 7
Illusion Dotz 3.3
Mounting
NOTICE: The suitable enviromental temperature for this lighting fixture is between -25˚ C to 45˚ C. Do not place this lighting
fixture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the fixture
to run at its best and help prolong the fixture life.
Illusion Dotz 3.3
Set Up
Power Supply: The ADJ Illusion Dotz 3.3 contains a electronic volt-
age switch, which will auto sense the voltage when it is plugged into
the power source. With the electronic ballast you do not need to worry
about wall voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Screw one clamp each via a M12 screw and nut onto the
Omega holders. Insert the quick-lock fasteners of the first
Omega holder into the respective holes on the bottom of the
Illusion Dotz 3.3. Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder. Pull the safety-cable
through the holes on the bottom of the base and over the trussing system or a safe fixation spot. Insert the end in the carabine
and tighten the safety screw.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 8
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Illusion Dotz 3.3 can be controlled via DMX-512 protocol. The Illusion Dotz 3.3 can be either a 12, 14, or 38 channel DMX
unit. The DMX address is set electronically using the controls on the
front panel of the unit. Your unit and your DMX
controller require a approved DMX-512 110 Ohm
Data cable for data input and data output (Figure
1). We recommend Accu-Cable DMX cables. If you
are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may
be purchased at almost all professional sound and
lighting stores). Your cables should be made with
Figure 1
a male and female XLR connector on either end of the cable. Also
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 9
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
Illusion Dotz 3.3
SOUND
Set Up
remember that DMX cable must be daisy chained and cannot be split.
POWER
POWER
REMOTE
CONTROL
INPUT
INPUT
OUTPUT
Illusion Dotz 3.3
Set Up
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
POWER
Notice: Be sure to follow figures two and three when making your own
cables. Do not use the
ground lug on the XLR connector. Do not conDMX512
DMX+,DMX-,COMMON
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
3-Pin XLR to 5-Pin XLR Conversion
COMMON
DMX512 OUT
3-PIN XLR
1
2
DMX +
3
3
DMX -
1
2
DMX512 IN
3-PIN XLR
3
Figure 2
1
2
Conductor
Termination reduces signal errors and
avoids signal transmission problems
Ground/Shield
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
Compliment
(- signal)
and PIN 3 (DMX +) of Data
the last
fixture.
Data True (+ signal)
XLR Female Socket
XLR Male Socket
1 Ground
2 Cold
2 Cold
1 Ground
XLR Pin Configuration
Pin 1 = Ground
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Pin 1
Pin 1
Pin 2
Pin 2
Pin 3
Pin 3
Not Used
Pin 4 - Do Not Use
Not Used
Pin 5 - Do Not Use
Pin 2 = Data Compliment (negative)
REMOTE
CONTROL
INPUT
SOUND
3 Hot
OUTPUT
INPUT
SOUND
3 Hot
REMOTE
Pin
3 = Data
(positive)
INPUTTrue
OUTPUT
CONTROL
INPUT
Figure 3
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
POWER
3
1
2
DMX512 IN
3-PIN XLR
3
1
2
POWER
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 10
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 11
Illusion Dotz 3.3
Receive Set Address
User Mode
User Mode
A001~AXXX
DMX address setting
Standard
User’s mode to change channel
Basic
numbers
Extend
User A
User B
Edit A
Edit B
Edit C
Status
User C
Max Channel
PAN
:
Remote Add
No DMX Status
Pan Invert
Tilt Invert
Pan Degree
Feedback
Move.Spd
Mic.Sens
Fixture ID
Stand By
Service PIN
RDM PID
Device IP Addr
Ctrl IP Addr
Function
Universe
Protocol Set
Kling-Net
Net Switch
ArtNet
ON/OFF
Fan Set
Head Fan
Dim Curve
ON/OFF
Blackout/Hold/Auto/Sound
ON/OFF
ON/OFF
Tilt Reverse movement
Pan Degree Select
Movement Feedback switch
630/540
ON/OFF
Movement Mode Select
Sensitivity of Mic.
Speed 1~ 4
0~99%
OFF, 01M~99M
Add. via DMX
Auto run if no DMX
Pan Reverse movement
15M
Stand By Mode
Password=XXX
Service Code
Xxxxxx
RDM Unique PID setting
Set the Device IP address
Xxx.xxx.xxx.xxx
Xxx.xxx.xxx.xxx
xxx
=050
Set the Console IP address
Port number
(Default Kling-Net)
Ethernet Switch
Auto
Fans Speed Mode Select
50%
75%
95%
02~60m 05m
ON/OFF
ON/OFF
ON/OFF
Backlight
Flip Display
Key Lock
DispFlash
Standard, Stage, TV, Architectural, Theater
Display shutoff time
Display Flip 180
Key Lock
Display flashes when NoSignal
Temp. C/F
Celsius
Fahrenheit
Temperature switch
between /
Init.Effect
PAN =XXX
Initial effect position
Disp.Set
Chan.Value
Slave Set
Auto.Pro
Sound.Ctrl
DFSE
Information
Preset User modes
High
Low
Base Fan
LCD.Set
Test
System Menu
PAN……
Slave1,Slave2,Slave3
Master / Alone
Master / Alone
Value of channel is displayed
Slave receive location choice
Auto program
Music control
Restore factory set
ON/OFF
Time.Info
Current
Total Time
Last Clear
Timer PIN
Clear Last
Power on running time (Hours)
Fixture running time (Hours)
Fixture Last times clear (Hours)
Timer
Password
Password=050
ON/OFF
Temp. Info
Error. Info
Model. Info
Software.V
Head Temp.
Pan,Tilt…..
Temperature in the head
Reset the error message
XXXX
1U01 V1.00……
2U01 V1.00……
Lamps Model Information
Software version information of
each IC
Reset.M
Test.Chan
Panel.Ctrl.
Pan&Tilt
Reset Pan/Tilt
PAN ……
Test function
Calibrate
Select .Pro
PAN =XXX
:
Adjustment of the lamp
-PasswordPAN
:
Pro. Part 1 = Program 1 ~ 9 Program 1
Calbrate and adjust the effects to
standard position
Password “050”
Select programs to be run
Program
Pro. Part 2 = Program 1 ~ 9 Program 2
Pro. Part 3 = Program 1 ~ 9 Program 3
Edit. Pro
Edit.Sce
Sce.Input
Program 1
:
Program 9
Edit Scene 001
~ Edit Scene 250
XX~XX
Program Test
Step 01=SCxxx
Step 64=SCxxx
Pan,Tilt,……
Fade Time
Secne Time
Input By Outside
Testing program
Program in loop
Save and exit
Manually enter the scene
Fade Time
Secne Time
External console scene input
Automatic recording scene
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 12
Illusion Dotz 3.3
System Menu
The main menu is accessed by pressing the MODE button. Browse
through the menu by using the UP, DOWN, RIGHT, & LEFT buttons.
Press the ENTER button to access the desired menu. You can scroll
through the submenus using the UP, DOWN, RIGHT, & LEFT buttons.
To confirm every selection press the ENTER button. You can exit
every menu and submenu by pressing the MODE button. The unit will
automatically exit the menus if no buttons are pressed after 10 seconds. These next pages will explain each function in the menu layout
located on the previous page.
RECEIVE
SET ADDRESS - With this function, you can adjust the desired DMXaddress via the Control Board.
1. Access the main menu, and press the UP or DOWN buttons so
that “Receive” is higlighted, then press ENTER.
2. “Set Address” will be displayed, press ENTER. The current DMX
address will now be displayed.
3. Use the UP or DOWN buttons to adjust the DMX address.
4. Press ENTER to confirm or press MODE to return to the main
menu.
USER MODE
USER MODE 1. Press the MODE button to access the main menu. Press the UP
or DOWN buttons so that “User Mode” is highlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “User Mode” is displayed,
press ENTER.
3. Use the UP or DOWN buttons to scroll through the 3 DMX Channel
Modes.
Standard Mode - This is 14 Channel Mode.
Basic Mode - This is 12 Channel Mode.
Extended Mode - This is 38 Channel Mode.
4. Press the MODE button once to return to the “User Mode” menu.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 13
Illusion Dotz 3.3
System Menu
Illusion Dotz 3.3
System Menu
Use the UP or DOWN buttons to scroll through the Edit modes. Press
ENTER to select any of the Edit modes.
value to “7”, Channel 2’s value to “7”, and Channel 3’s value to “57”.
Wait 20 seconds and the address should change on the unit to “57”.
Edit A, B, or C – This function allows the user to make the actual
changes in the user-defined modes that are created in the previous
function.
2ND EXAMPLE: If you want the address to be 420, you must first set
the address that is currently assingned to the unit. If you want the set
the address to 420, set Channel 1’s value to “7”, Channel 2’s value to
“8”, and Channel 3’s to “164”. (256 + 164 = 420).
Function REMOTE ADD - With this function you can adjust the DMX address
via external controller.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Status” is displayed, press
ENTER.
3. Press UP or DOWN buttons, until “Remote Add” is displayed,
and press ENTER.
4. Either “Off” or “On” will be displayed, use the UP and DOWN buttons to toggle between.
5. Press ENTER to confirm your selection or press MODE to exit.
To use this function follow these instructions:
To adjust the address of your unit you must first go to the address
that it is currently set to. From there you can adjust the address. First
make sure all channels are set to the value of “0”.
1. On your DMX controller set the DMX value of Channel 1 to the
value “7”.
2. Now set the DMX value of Channel 2 to the value “7” to adjust the
starting address between 1 and 255. To adjust the address between
256 and 511 set Channel 2 to the value “8” .
3. Set the DMX value of Channel 3 to your desired starting address.
This will take about 20 seconds before the unit accepts the new DMX
address.
EXAMPLE: If you want the address to be 57, you must first set the
address that is currently assingned to the unit. Then set Channel 1’s
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 14
NO DMX STATUS - With this function if the DMX signal is suddenly
lost, the unit will automatically go into 1 of 4 modes.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Status” is displayed, press
ENTER.
3. Press UP or DOWN buttons, until “No DMX Status” is displayed,
and press ENTER.
4. Either “Hold” (Last DMX setting), “Close” (Blackout), “Music”
(Sound Active), or “Auto” (Auto Program) will be displayed, use the
UP and DOWN buttons to toggle between.
5. Press ENTER to confirm your selection or press MODE to exit.
PAN INVERT - With this function you can reverse the Pan movement.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Status” is displayed, press
ENTER.
3. Press UP or DOWN buttons, until “Pan Invert” is displayed, and
press ENTER.
4. Either “Off” or “On” will be displayed, use the UP and DOWN buttons to toggle between.
5. Press ENTER to confirm your selection or press MODE to exit.
TILT INVERT - With this function you can reverse the Tilt movement.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 15
Illusion Dotz 3.3
System Menu
2. Press the UP or DOWN buttons until “Status” is displayed, press
ENTER.
3. Press UP or DOWN buttons, until “Tilt Invert” is displayed, and
press ENTER.
4. Either “Off” or “On” will be displayed, use the UP and DOWN buttons to toggle between.
5. Press ENTER to confirm your selection or press MODE to exit.
PAN DEGREE - With this function you can change the pan degree
from 630 to 540.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
Illusion Dotz 3.3
System Menu
movement speed.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Status” is displayed, press
ENTER.
3. Press UP or DOWN buttons, until “Move Speed” is displayed,
and press ENTER.
4. Either “Speed 1”, “Speed 2”, “Speed 3” or “Speed 4” will be displayed, use the UP and DOWN buttons to toggle between.
5. Press ENTER to confirm your selection or press MODE to exit.
3. Press UP or DOWN buttons, until “Pan Degree” is displayed, and
press ENTER.
MIC SENS - With this function you can set the microphone sensitivity. The default setting is 70%. You can adjust the sensitivity between
0%-99%
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
4. Either “540” or “630” will be displayed, use the UP and DOWN
buttons to toggle between.
2. Press the UP or DOWN buttons until “Status” is displayed, press
ENTER.
5. Press ENTER to confirm your selection or press MODE to exit.
3. Press UP or DOWN buttons, until “Mic Sensitivity” is displayed,
and press ENTER.
2. Press the UP or DOWN buttons until “Status” is displayed, press
ENTER.
FEEDBACK - With this function you can feedback switch the pan
movement or tilt movement.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Status” is displayed, press
ENTER.
3. Press UP or DOWN buttons, until “Feedback” is displayed, and
press ENTER.
4. Either “Off” or “On” will be displayed, use the UP and DOWN buttons to toggle between.
5. Press ENTER to confirm your selection or press MODE to exit.
MOVEMENT SPEED - With this function you can set the pan and tilt
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 16
4. Use the UP and DOWN buttons to adjust the mic sensitivity
between 0%-99%.
5. Press ENTER to confirm your selection or press MODE to exit.
STAND BY - With this function the LEDs and step motors will power
off if there is no DMX signal within 15 mins (factory defualt). Once it
receives a DMX signal, the fixture will reset itself.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Status” is displayed, press
ENTER.
3. Press UP or DOWN buttons, until “Stand By” is displayed, and
press ENTER.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 17
Illusion Dotz 3.3
System Menu
4. “15M” will be displayed, use the UP and DOWN buttons to adjust
the hibernation period between 01M-99M or “Off”.
5. Press ENTER to confirm your selection or press MODE to exit.
Fixture ID
SERVICE PIN - With this function you can enter the RDM password
so that you can access and change the RDM ID number.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Fixture ID” is displayed,
press ENTER.
3. Press UP or DOWN buttons, until “Service PIN” is displayed, and
press ENTER.
4. The “Password” is 050.
5. Press ENTER or press MODE to exit.
RDM PID - RDM stands for “Remote Device Management”. This
feature lets you control every aspect of your fixture remotely from an
RDM controller. Manual settings like adjusting the DMX address are
no longer needed. This is especially useful when the unit is installed
in a remote area.
In this submenu you can see the units RDM ID number and adjust it
as well.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Fixture ID” is displayed,
press ENTER.
3. Press UP or DOWN buttons, until “RDM PID” is displayed, and
press ENTER.
4. “XXXXXX” will be displayed. “XXXXXX” represents the units current
RDM ID.
5. Press ENTER or press MODE to exit.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 18
Illusion Dotz 3.3
System Menu
DEVICE IP ADDR - With this function you set the Device IP address.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Fixture ID” is displayed,
press ENTER.
3. Press UP or DOWN buttons, until “Device IP Addr” is displayed,
and press ENTER.
4. “XXX XXX XXX XXX” will be displayed. “XXX XXX XXX XXX” represents the units current Device IP Address.
5. Press ENTER or press MODE to exit.
CTRL IP ADDR - With this function you set the Console IP address.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Fixture ID” is displayed,
press ENTER.
3. Press UP or DOWN buttons, until “Ctrl IP Addr” is displayed, and
press ENTER.
4. “XXX XXX XXX XXX” will be displayed. “XXX XXX XXX XXX” represents the units current Device IP Address.
5. Press ENTER or press MODE to exit.
UNIVERSE - With this function you can enter the port number.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Fixture ID” is displayed,
press ENTER.
3. Press UP or DOWN buttons, until “Universe” is displayed, and
press ENTER.
4. “XXX” will be displayed. “XXX” represents the units current Device
IP Address.
5. Press ENTER or press MODE to exit.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 19
Illusion Dotz 3.3
System Menu
Illusion Dotz 3.3
System Menu
Protocol Set
toggle between.
KLING-NET/ARTNET - With this function you can select the software for which you are going to control the fixture.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
4. Press ENTER to confirm your selection or press MODE to exit.
2. Press the UP or DOWN buttons until “Protocol Set” is displayed,
press ENTER.
3. Either “Kling-Net” or “ArtNet” will be displayed. Use the UP
or DOWN buttons, to find the software you wish to use, and press
ENTER to select.
4. Press the MODE button to exit.
Net Switch
NET SWITCH - This function will activate the unit to receive KlingNet/ArtNet signal.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Net Switch” is displayed,
press ENTER.
3. Either “On” or “Off” will be displayed. To activate the Net Switch
use the UP or DOWN buttons to select “On”, and press ENTER to
select.
4. Press the MODE button to exit.
Fan Set
HEAD FAN - With this function you can adjust the speed of the
moving head fans.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Head Fan” is displayed,
press ENTER.
3. Either “Auto Fan Speed” (default), “Low Fan Speed”, or “High
Fand Speed” will be displayed, use the UP and DOWN buttons to
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 20
BASE FAN - With this function you can adjust the speed of the base
fans.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Base Fan” is displayed,
press ENTER.
3. Either “Auto Fan Speed” (default), “Low Fan Speed”, or “High
Fand Speed” will be displayed, use the UP and DOWN buttons to
toggle between.
4. Press ENTER to confirm your selection or press MODE to exit.
LCD Setting
BACKLIGHT - With this function you can have the LCD display after
2-60 minutes. Use this function to adjust the time.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “LCD Set” is displayed, press
ENTER.
3. Press UP or DOWN buttons, until “Backlight” is displayed, and
press ENTER.
4. “05m” (5 minutes) will be displayed, use the UP and DOWN buttons to adjust the shutoff time between 02m-60m or “Off”.
5. Press ENTER to confirm your selection or press MODE to exit.
FLIP DISPLAY - With this function you can rotate (flip) the display
180 degrees.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “LCD Set” is displayed, press
ENTER.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 21
Illusion Dotz 3.3
System Menu
Illusion Dotz 3.3
System Menu
3. Press UP or DOWN buttons, until “Flip Display” is displayed, and
press ENTER.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
4. Either “Off” or “On” will be displayed, use the UP and DOWN buttons to toggle between.
2. Press the UP or DOWN buttons until “Dim Curve” is displayed,
press ENTER.
5. Press ENTER to confirm your selection or press MODE to exit.
3. Either “Standard”, “Stage”, “TV”, “Architectural”, or “Theatre”
will be displayed, use the UP and DOWN buttons to toggle between.
KEY LOCK - With this function activated the buttons will lock autommatically after 15 seconds.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “LCD Set” is displayed, press
ENTER.
3. Press UP or DOWN buttons, until “Key Lock” is displayed, and
press ENTER.
4. Either “Off” or “On” will be displayed, use the UP and DOWN buttons to toggle between.
5. Press ENTER to confirm your selection or press MODE to exit.
DISPFLASH - With this function activated the the display will flash
when there is not DMX signal.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “LCD Set” is displayed, press
ENTER.
3. Press UP or DOWN buttons, until “DispFlash” is displayed, and
press ENTER.
4. Either “Off” or “On” will be displayed, use the UP and DOWN buttons to toggle between.
5. Press ENTER to confirm your selection or press MODE to exit.
Dimmer Curve
DIM CURVE - Select 1 of 5 dimming curves. See page 45 for the
dimming curve chart.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 22
5. Press ENTER to confirm your selection or press MODE to exit.
Temp. C/F
TEMP. C/F - With this function, you can change the temperature display to show either Celsius or Fahrenheit.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press UP or DOWN buttons, until “Temp. C/F” is displayed, and
press ENTER.
3. Either “Celsius” or “Fahrenheit” will be displayed, use the UP and
DOWN buttons to toggle between.
4. Press ENTER to confirm your selection or press MODE to exit.
Init. Effect
INIT. EFFECT - In this menu you are able to check initial effect position.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press UP or DOWN buttons, until “Init. Effect” is displayed, and
press ENTER.
3. “XXX” will be displayed. “XXX” represents the current effect position.
4. Press ENTER or press MODE to exit.
CHANNEL VALUE - This function will allow you to see the DMX
value of each DMX channel that is currently being used at the time.
1. Access the main menu, and press the UP or DOWN buttons so
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 23
Illusion Dotz 3.3
System Menu
that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “DMX Value” is displayed,
and press ENTER.
3. A DMX Channel will be displayed. Example: Prism, Color Wheel,
Gobo Wheel, etc... Press ENTER when you find the DMX channel that
you would like to check. When you press ENTER the DMX value of
that channel will displayed.
4. Press the MODE button to exit.
SLAVE SET - This function lets you designate the unit as the slave in
a Master-Slave configuration.
1. Access the main menu, and press the UP or DOWN buttons so
that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Slave Set” is displayed, and
press ENTER.
3. Either Slave 1, Slave 2, or Slave 3 will be displayed. Press ENTER
to select either of the three, or press MODE button to exit.
AUTO PROGRAM - This function allows the internal programs to
run in either stand-alone or master/slave mode. In “Master” mode
the fixture will send DMX data to other fixtures connect via the DMX
chain. In “Alone” mode the fixture will operate as a single fixture. The
program for this mode is selected in the “Select program” section of
the control menu. You can set the number of steps under “Edit program”. You can edit the individual scenes under “Edit scenes”. With
this function, you can run the individual scenes either automatically,
i.e. with the adjusted Step-Time.
1. Access the main menu, and press the UP or DOWN buttons so
that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Auto Program” is displayed,
and press ENTER.
3. Either “Master” or “Alone” will be displayed.
4. Press ENTER to to make your selection, or press MODE button to
exit.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 24
Illusion Dotz 3.3
System Menu
SOUND CONTROL - With this function, the internal program will run
in sound active mode.
1. Access the main menu, and press the UP or DOWN buttons so
that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Sound Control” is displayed, press ENTER.
3. Either “Master” or “Alone” will be displayed. Use the UP or DOWN
buttons to change the operating mode.
4. Press ENTER to to make your selection, or press MODE button to
exit.
DEFAULT RESET 1. Access the main menu, and press the UP or DOWN buttons so
that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “DFSE” is displayed, press
ENTER.
3. Either “Off” or “On” will be displayed, use the UP and DOWN buttons to toggle between.
4. Press ENTER to confirm your selection or press MODE/ESC to
exit.
INFORMATION
Time Information (Time information is always represented in
hours)
CURRENT RUNNING TIME - This will allow you to check the units
current running time.
1. Press the MODE button to access the main menu. Press the UP
or DOWN buttons so that “Information” is highlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “Time Information” is displayed, press ENTER.
3. Press UP or DOWN buttons, until “Current” is displayed, and
press ENTER.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 25
Illusion Dotz 3.3
System Menu
Illusion Dotz 3.3
System Menu
4. “XXXX” will now be displayed. “XXXX” represents the current running time.
2. Press the UP or DOWN buttons until “Time Information” is displayed, press ENTER.
5. Press ENTER or press MODE to exit.
3. Press UP or DOWN buttons, until “Timer Pin” is displayed, and
press ENTER.
TOTAL RUNNING TIME - This will allow you to check the units total
running time.
1. Press the MODE button to access the main menu. Press the UP
or DOWN buttons so that “Information” is highlighted, then press
ENTER.
4. The “Timer Pin” is 050.
5. Press ENTER or press MODE to exit.
3. Press UP or DOWN buttons, until “Total Time” is displayed, and
press ENTER.
CLEAR LAST - This will allow you to clear the last run time of the
unit. You need to put in the Timer PIN before doing this. Please see
the section before this.
1. Press the MODE button to access the main menu. Press the UP
or DOWN buttons so that “Information” is highlighted, then press
ENTER.
4. “XXXX” will now be displayed. “XXXX” represents the total running time.
2. Press the UP or DOWN buttons until “Time Information” is displayed, press ENTER.
5. Press ENTER or press MODE to exit.
3. Press UP or DOWN buttons, until “Clear Last” is displayed, and
press ENTER.
2. Press the UP or DOWN buttons until “Time Information” is displayed, press ENTER.
LAST CLEAR - This will allow you to check when the last running
time was cleared.
1. Press the MODE button to access the main menu. Press the UP
or DOWN buttons so that “Information” is highlighted, then press
ENTER.
4. Either “Off” or “On” will be displayed, use the UP and DOWN buttons to toggle between.
5. Press ENTER to confirm your selection or press MODE to exit.
3. Press UP or DOWN buttons, until “Last Clear” is displayed, and
press ENTER.
TEMPERATURE INFO - This will allow you to check the moving
head temperature.
1. Press the MODE button to access the main menu. Press the UP
or DOWN buttons so that “Information” is highlighted, then press
ENTER.
4. “XXXX” will now be displayed. “XXXX” represents the last running
time.
2. Press the UP or DOWN buttons until “Temp. Info” is displayed,
press ENTER.
5. Press ENTER or press MODE to exit.
3. “Head Tem.” will now be displayed, press ENTER.
2. Press the UP or DOWN buttons until “Time Information” is displayed, press ENTER.
RUN PASSWORD - This will display the timer password.
1. Press the MODE button to access the main menu. Press the UP
or DOWN buttons so that “Information” is highlighted, then press
ENTER.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 26
4. “XXX” will now be displayed. “XXX” represents the current temperature of the moving head.
5. Press ENTER or press MODE to exit.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 27
Illusion Dotz 3.3
System Menu
ERROR INFO - In this menu you are able to reset the error message.
1. Press the MODE button to access the main menu. Press the UP
or DOWN buttons so that “Information” is highlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “Error Info” is displayed,
press ENTER.
3. Use the UP or DOWN buttons to find the error message that needs
to be cleared.
4. Press ENTER or press MODE to exit.
MODEL INFO - In this menu you are able to see the lamps model
information.
1. Press the MODE button to access the main menu. Press the UP
or DOWN buttons so that “Information” is highlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “Model Info” is displayed,
press ENTER.
3. “XXXX” will now be displayed. “XXXX” represents the model information.
4. Press MODE to exit.
SOFTWARE VERSION - This will allow you to see the software version of each IC.
1. Press the MODE button to access the main menu. Press the UP
or DOWN buttons so that “Information” is highlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “Software Version” is displayed, press ENTER.
3. Use the UP or DOWN buttons to scroll through each IC and see
the software version.
4. Press MODE to exit.
Illusion Dotz 3.3
System Menu
TEST
RESET MOTORS - With this function you can reset the Pan & Tilt
motors.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Test” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Reset Motor” is displayed,
press ENTER.
3. Press ENTER to reset or press MODE to exit.
TEST CHANNEL - With this function you can test/correct each channel function.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Test” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Test Channel” is displayed,
press ENTER.
3. Use the UP or DOWN buttons to scroll through the various channels.
4. Press ENTER or press MODE to exit.
PANEL CTRL. - With this function you can easily adjust the lamp. All
effects will be canceled, the shutter will open and output intensity will
be 100%. With the individual functions you can focus the light on flat
surface (a wall) and finely adjust the lamp.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Test” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Panel Ctrl.” is displayed,
press ENTER.
3. Use the UP or DOWN buttons to scroll through the various functions. Press ENTER when you find the function you would like to
adjust.
4. Press ENTER or press MODE to exit.
CALIBRATION - With this function you can calibrate and adjust the
effects wheels to their correct positions. The Calibration password
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 28
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 29
Illusion Dotz 3.3
System Menu
050.
1. Press the MODE button to access the main menu. Press the UP
or DOWN buttons so that “Effect Adjust” is highlighted, then press
ENTER.
2. Press the UP or DOWN buttons until “Calibration” is displayed,
press ENTER.
3. “XXXX” will be displayed. The password is 050.
4. Press ENTER to confirm or press MODE to exit.
PROGRAM - The fixture comes equipped with a built-in DMX
recorder that allows custom programs to be installed and recalled
directly from the fixture’s control board. Programs can be created and
stored using the fixture’s control board or by using an external DMX
controller.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Program” is highlighted, then press ENTER.
2. Use the UP or DOWN buttons to find and access one of the below
submenus.
Select Program – This function allows the user to select one of ten
of the user defined built-in programs. This program is then accessed
in “Function Mode” under “Program Run.”
Edit Program – This function allows the user to edit the built-in programs.
Edit Scene – This function allows the user to edit or define the actual
scenes that are stored in the user defined built-in programs that are
accessed in the previous step.
Scene Input - The Illusion Dotz 3.3 features an integrated DMX
recorder. Preprogrammed scenes can be transmitted to the fixture via
any DMX compliant controller. This function allows those scenes to
be stored in to the fixture’s built-in memory and
then subsequently used to create the user-defined programs.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 30
Illusion Dotz 3.3
Operation
Universal DMX Control: This function allows you to use a universal DMX-512 controller to control head movement, RGB colors,
master dimmer, shutter (strobe), and various other features. A DMX
controller allows you to create unique programs tailored to your individual needs.
1. The Illusion Dotz 3.3 has a 12 Channel mode, 14 Channel mode, and 38 Channel mode. See pages 34-43 for detailed description of the DMX traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 13-15 as well as the set-up specifications that are
included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the directions on page 36 to select your DMX Channel mode, and follow the instruction on page 17 to set the DMX
address.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
Stand-Alone (Sound Active or Auto Program): This mode allows
a single unit to run to the beat of the music or run through a built-in
program.
AUTO PROGRAM:
1. Access the main menu, and press the UP or DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Disp Set” is displayed, and press ENTER.
3. Press the UP or DOWN buttons until “Auto Pro” is displayed, and press ENTER.
4. Either “Master” or “Alone” will be displayed. Using the UP or DOWN buttons select “Alone” and press ENTER.
SOUND ACTIVE:
1. Access the main menu, and press the UP or DOWN buttons so that “Function” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until “Disp Set” is displayed, and press ENTER.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 31
Illusion Dotz 3.3
Operation
3. Press the UP or DOWN buttons until “Sound Ctrl.” is displayed, and press ENTER.
4. Either “Master” or “Alone” will be displayed. Using the UP or DOWN buttons select “Alone” and press ENTER.
Master-Slave Configuration (Sound Active or Auto Program):
This function will allow you to link up to 16 units together and operate without a controller. The units can run a built-in program or run in
sound actiive mode. In a Master-Slave set up one unit will act as the
controlling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave.
1. Using standard XLR microphone cables, daisy chain your units together via the XLR connector on the rear of the units. Remem-
ber the Male XLR connector is the input and the Female XLR connector is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a terminator at the last fixture.
2. On your “Master” unit, access the main menu, and press the UP
or DOWN buttons so that “Function” is highlighted, then press ENTER.
3. Press the UP or DOWN buttons until “Disp Set” is displayed, and press ENTER.
4. Select your desired operating mode. Use the UP or DOWN but-
tons to select between “Auto Pro” or “Sound Ctrl”, press ENTER to select your desired program.
5. Either “Master” or “Alone” will be displayed. Using the UP or DOWN buttons select “Master” and press ENTER.
6. For your “Slave” units, access the main menu, and press the UP
or DOWN buttons so that “Function” is highlighted, then press ENTER.
7. Press the UP or DOWN buttons until “Disp Set” is displayed, and press ENTER.
8. Press the UP or DOWN buttons until “Slave Mode” is displayed, and press ENTER.
9. Either Slave 1, Slave 2, or Slave 3 will be displayed. Select your desired Slave setting and press ENTER.
10. Press MODE if you want to return to the main menu.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 32
Illusion Dotz 3.3
Kling-Net or Art-Net Operation
1. Activate the Net Switch using the instructions on page 20 under “Net Switch”. Select your software using the instructions on page 20 under “Kling-Net/Artnet”.
2. Install one of the recommended operating softwares onto your computer. Recommended softwares; Arkaos Media Master
Express, Media Master Pro, or LED Master (Sold Separately).
3. Connect the panels via CAT 5 Straight Network cable. When
creating your own custom cable, use RJ45 Straight Network cable.
4. Map the fixtures using KlingNetMapper or Art-Net Mapper.
5. Control the fixtures using ArKaos or Art-Net software. Please refer to the media playback software user manual for further instruc-
tions.
Note: ArKaos Kling-Net requires a gigabit (1000 mbps) Ethernet card
and network router for a smoother operation.
Installation method 1:
Note: Do not daisy-chain more thean 25 units when connected directly from the computer.
Use a Ethernet Switch if more than 25 units are being controlled.
When connecting you must use a CAT 5 Straight Network cable.
Installation method 2:
Note:1.The Ethernet Switch must be Gigabit Switch.
2. Do not daisy-chain more than 25pcs units from a single network port of the Ethernet Switch.
3. Maximum 2 output network ports of the Ethernet Switch can be used. So the system can control 25pcs
maximum.
When connecting you must use a CAT 5 Straight Network cable.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 33
Illusion Dotz 3.3 Channel
1
2
3
4
5
6
7
8
9
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
0 - 255
0 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101 - 255
0 - 10
11 - 20
21 - 30
31 - 40
41 - 50
51 - 60
61 - 70
12 Channel DMX Mode
Function
PAN MOVEMENT 8bit
TILT MOVEMENT 8bit
ALL RED
0% - 100%
ALL GREEN
0% - 100%
ALL BLUE
0% - 100%
SHUTTER & STROBE
LED’S OFF
LED’S ON
STROBING SLOW - FAST LED’S ON
PULSE EFFECT IN SEQUENCES
LED’S ON
RANDOM STROBE SLOW - FAST
LED’S ON
DIMMER
INTENSITY 0% - 100%
DIMMER CURVES
STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
DEFAULT TO UNIT SETTING
AUTO PROGRAMS
PROGRAM 1
PROGRAM 2
PROGRAM 3
PROGRAM 4
PROGRAM 5
PROGRAM 6
PROGRAM 7
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 34
Illusion Dotz 3.3 Channel
9
10
11
12
Value
71 - 80
81 - 90
91 - 100
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
161 - 170
171 - 180
181 - 190
191 - 200
201 - 210
211 - 220
221 - 230
231 - 240
241 - 250
251 - 255
0 - 255
0 - 225
226 - 235
246 - 255
0 - 79
80 - 84
85 - 96
97 - 99
100 - 119
120 - 139
140 - 159
12 Channel DMX Mode
Function
AUTO PROGRAMS
PROGRAM 8
PROGRAM 9
PROGRAM 10
PROGRAM 11
PROGRAM 12
PROGRAM 13
PROGRAM 14
PROGRAM 15
PROGRAM 16
PROGRAM 17
PROGRAM 18
PROGRAM 19
PROGRAM 20
PROGRAM 21
PROGRAM 22
PROGRAM 23
PROGRAM 24
PROGRAM 25
GRADIENT EFFECT
PROGRAM SPEED
SLOW - FAST
PAN/TILT MOVEMENT SPEED
MAX TO MIN. SPEED
BLACKOUT BY MOVEMENT
NO FUNCTION
LAMP ON/OFF, RESET & PROGRAMS
NORMAL
ALL MOTOR RESET
NO FUNCTION
OTHER MOTOR RESET
INTERNAL PROGRAM 1
INTERNAL PROGRAM 2
INTERNAL PROGRAM 3
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 35
Illusion Dotz 3.3 Channel
12
Value
160 - 179
180 - 199
200 - 219
220 - 239
240 - 255
12 Channel DMX Mode
Function
INTERNAL PROGRAM 4
INTERNAL PROGRAM 5
INTERNAL PROGRAM 6
INTERNAL PROGRAM 7
SOUND ACTIVE PROGRAM
Illusion Dotz 3.3 Channel
1
2
3
4
5
6
7
8
9
10
11
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 36
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
0 - 255
0 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101 - 255
0 - 10
11 - 20
21 - 30
31 - 40
14 Channel DMX Mode
Function
PAN MOVEMENT 8bit
PAN FINE 16bit
TILT MOVEMENT 8bit
TILT FINE 16bit
ALL RED
0% - 100%
ALL GREEN
0% - 100%
ALL BLUE
0% - 100%
SHUTTER & STROBE
LED’S OFF
LED’S ON
STROBING SLOW - FAST LED’S ON
PULSE EFFECT IN SEQUENCES
LED’S ON
RANDOM STROBE SLOW - FAST
LED’S ON
DIMMER
INTENSITY 0% - 100%
DIMMER CURVES
STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
DEFAULT TO UNIT SETTING
AUTO PROGRAMS
PROGRAM 1
PROGRAM 2
PROGRAM 3
PROGRAM 4
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 37
Illusion Dotz 3.3 Channel
11
12
13
14
Value
0 - 10
11 - 20
21 - 30
31 - 40
71 - 80
81 - 90
91 - 100
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
161 - 170
171 - 180
181 - 190
191 - 200
201 - 210
211 - 220
221 - 230
231 - 240
241 - 250
251 - 255
0 - 255
0 - 225
226 - 235
246 - 255
0 - 79
80 - 84
85 - 96
14 Channel DMX Mode
Function
AUTO PROGRAMS
PROGRAM 1
PROGRAM 2
PROGRAM 3
PROGRAM 4
PROGRAM 8
PROGRAM 9
PROGRAM 10
PROGRAM 11
PROGRAM 12
PROGRAM 13
PROGRAM 14
PROGRAM 15
PROGRAM 16
PROGRAM 17
PROGRAM 18
PROGRAM 19
PROGRAM 20
PROGRAM 21
PROGRAM 22
PROGRAM 23
PROGRAM 24
PROGRAM 25
GRADIENT EFFECT
PROGRAM SPEED
SLOW - FAST
PAN/TILT MOVEMENT SPEED
MAX TO MIN. SPEED
BLACKOUT BY MOVEMENT
NO FUNCTION
LAMP ON/OFF, RESET & PROGRAMS
NORMAL
ALL MOTOR RESET
NO FUNCTION
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 38
Illusion Dotz 3.3 Channel
14
14 Channel DMX Mode
Value
Function
LAMP ON/OFF, RESET & PROGRAMS
97 - 99
OTHER MOTOR RESET
100 - 119
INTERNAL PROGRAM 1
120 - 139
INTERNAL PROGRAM 2
140 - 159
INTERNAL PROGRAM 3
160 - 179
INTERNAL PROGRAM 4
180 - 199
INTERNAL PROGRAM 5
200 - 219
INTERNAL PROGRAM 6
220 - 239
INTERNAL PROGRAM 7
240 - 255
SOUND ACTIVE PROGRAM
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 39
Illusion Dotz 3.3 Channel
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
38 Channel DMX Mode
Function
PAN MOVEMENT 8bit
PAN FINE 16bit
TILT MOVEMENT 8bit
TILT FINE 16bit
RED 1
0% - 100%
GREEN 1
0% - 100%
BLUE 1
0% - 100%
RED 2
0% - 100%
GREEN 2
0% - 100%
BLUE 2
0% - 100%
RED 3
0% - 100%
GREEN 3
0% - 100%
BLUE 3
0% - 100%
RED 4
0% - 100%
GREEN 4
0% - 100%
BLUE 4
0% - 100%
RED 5
0% - 100%
GREEN 5
0% - 100%
BLUE 5
0% - 100%
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 40
Illusion Dotz 3.3 Channel
20
21
22
23
24
25
26
27
28
29
30
31
32
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
38 Channel DMX Mode
Function
RED 6
0% - 100%
GREEN 6
0% - 100%
BLUE 6
0% - 100%
RED 7
0% - 100%
GREEN 7
0% - 100%
BLUE 7
0% - 100%
RED 8
0% - 100%
GREEN 8
0% - 100%
BLUE 8
0% - 100%
RED 9
0% - 100%
GREEN 9
0% - 100%
BLUE 9
0% - 100%
SHUTTER & STROBE
LED’S OFF
LED’S ON
STROBING SLOW - FAST LED’S ON
PULSE EFFECT IN SEQUENCES
LED’S ON
RANDOM STROBE SLOW - FAST
LED’S ON
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 41
Illusion Dotz 3.3 Channel
33
34
35
Value
0 - 255
0 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101 - 255
0 - 10
11 - 20
21 - 30
31 - 40
71 - 80
81 - 90
91 - 100
101 - 110
111 - 120
121 - 130
131 - 140
141 - 150
151 - 160
161 - 170
171 - 180
181 - 190
181 - 190
191 - 200
201 - 210
211 - 220
221 - 230
231 - 240
241 - 250
251 - 255
38 Channel DMX Mode
Function
DIMMER
INTENSITY 0% - 100%
DIMMER CURVES
STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
DEFAULT TO UNIT SETTING
AUTO PROGRAMS
PROGRAM 1
PROGRAM 2
PROGRAM 3
PROGRAM 4
PROGRAM 8
PROGRAM 9
PROGRAM 10
PROGRAM 11
PROGRAM 12
PROGRAM 13
PROGRAM 14
PROGRAM 15
PROGRAM 16
PROGRAM 17
PROGRAM 18
PROGRAM 19
PROGRAM 19
PROGRAM 20
PROGRAM 21
PROGRAM 22
PROGRAM 23
PROGRAM 24
PROGRAM 25
GRADIENT EFFECT
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 42
Illusion Dotz 3.3 Channel
36
37
38
Value
0 - 255
0 - 225
226 - 235
246 - 255
0 - 79
80 - 84
85 - 96
97 - 99
100 - 119
120 - 139
140 - 159
160 - 179
180 - 199
200 - 219
220 - 239
240 - 255
38 Channel DMX Mode
Function
PROGRAM SPEED
SLOW - FAST
PAN/TILT MOVEMENT SPEED
MAX TO MIN. SPEED
BLACKOUT BY MOVEMENT
NO FUNCTION
LAMP ON/OFF, RESET & PROGRAMS
NORMAL
ALL MOTOR RESET
NO FUNCTION
OTHER MOTOR RESET
INTERNAL PROGRAM 1
INTERNAL PROGRAM 2
INTERNAL PROGRAM 3
INTERNAL PROGRAM 4
INTERNAL PROGRAM 5
INTERNAL PROGRAM 6
INTERNAL PROGRAM 7
SOUND ACTIVE PROGRAM
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 43
Illusion Dotz 3.3 Photometric Chart
Intensity(LUX)
6680
8340
11920
22900
2700
3140
4400
9280
1430
1680
2300
4600
730
1100
1450
2810
483
593
829
1920
3
Illusion Dotz 3.3 Beam opening(m)
2
0
10
1
2
3
0
Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning
1
10° Diameter(m)
Fuse Replacement
Fuse Replacement: Locate and remove the unit’s power cord. Once
the cord has been removed located the fuse holder located inside the
power socket. Insert a flat-head screw driver into the power socket
and gently pry out the fuse holder. Remove the bad fuse and replace
with a new one. The fuse holder has a built-in socket for a spare fuse
be sure not to confuse the spare fuse with active fuse.
Beam angle 10°
Red LEDs
Green LEDs
Blue LEDs
Full LEDs
Illusion Dotz 3.3 1
2
3
4
5
0.40
0.75
1.10
1.50
1.75
Illusion Dotz 3.3 Dimmer Curve Chart
the internal and external optical lenses and mirror should be carried
out periodically to optimize light output. Cleaning frequency depends
on the environment in which the fixture operates (I.e. smoke, fog
residue, dust, dew). In heavy club use we recommend cleaning on a
monthly basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.
5. Always be sure to dry all parts completely before plugging the unit back in.
Illusion Dotz 3.3 Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
Ramp Effect
(Fade Time)
(Fade Time)
Standard
Stage
TV
Architectural
Theatre
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 44
1. Be sure the external fuse has not blown. The fuse is located on the bottom panel of the unit.
2. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 45
Illusion Dotz 3.3 Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337 . Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
• Laser Products = 90-Day Limited Warranty
• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty).
ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 46
Illusion Dotz 3.3 Model: Specifications
Illusion Dotz 3.3
Voltage: 100~240V, 50/60Hz
LEDs:
9 x 30W RGB COB LEDs
Beam Angle:
15 Degrees
Power Consumption:
285W
Power Cord Daisy Chain: 4 Fixtures Max. (120V)
9 Fixtures Max. (220V)
Dimensions: 15”(L) x 10.5”(W) x 20.25”(H)
380mm x 264mm x 512mm
Weight:
29 Lbs. / 13 kgs.
Fuse:
4A
Duty Cycle:
None
DMX: 3 DMX Channel Modes: 12 Channels, 14 Channels, or 38 Channels
Sound Active:
Yes
Working Position:
Any Safe, Secure Position
Warranty:
2 Year (730 days)
Auto Sensing Voltage: This fixture contains an electronic
voltage switch, which will auto sense the voltage when it is
plugged into the power source.
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: [email protected]
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
s[email protected] / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement