Cisco | 827 - 827 Router - EN | Installation guide | Cisco 827 - 827 Router - EN Installation guide

Cisco 827 Router Cabling and Setup
Quick Start Guide
This document describes the basic process of cabling and configuring the Internet access device, the
Cisco 827 router. For advanced cabling information, refer to the Cisco 827 Routers Hardware Installation
Guide. For advanced configuration information, refer to the Cisco 827 Routers Software Configuration
Guide. These documents are available on the Cisco Documentation CD-ROM and on the World Wide Web.
You can access the most current Cisco documentation on the World Wide Web at the following sites:
•
http://www.cisco.com
•
http://www-china.cisco.com
•
http://www-europe.cisco.com
Parts List
The shipment of your Cisco 827 router includes the following items:
•
One Cisco 827 router
•
One yellow Ethernet cable
•
One lavender ADSL cable
•
One blue console cable
•
One DB-9-to-RJ-45 adapter (for use with the blue console cable)
•
One black power supply
•
One black power supply cord
•
800 and SOHO Series Product Documentation CD
Figure 1 shows the items included with the router. If any of the items is missing or damaged, contact
your customer service representative.
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2001. Cisco Systems, Inc. All rights reserved.
Verify the PC Setup
Figure 1
Items Included with the Router
er at
th t
O en
um
oc
D
n
io
Yellow Ethernet cable
rt
ta
S
e
ck id
ui u
Q G
n
tio
ta
en OM
um -R
oc D
D C
Lavender ADSL cable
Product documentation
Light blue console cable
o
c
is
C
0
80
Desktop power supply
Black power cord
Cisco 800
CD-ROM
DB-9-to-RJ-45 adapter
(for use with light blue console cable)
Verify the PC Setup
Before you begin, verify that each computer that will be connected to the router has a network interface
card (NIC) installed and that Transmission Control Protocol/Internet Protocol (TCP/IP) has been loaded
and configured. For more information on how to configure TCP/IP, refer to the PC Configuration
Instructions to Establish Cisco Router-to-PC Communications, which is available on the Cisco
Documentation CD-ROM, and refer to information available the Microsoft web site.
Verify the PC Setup
2
78-6853-03
Connect the Cisco 827 Router to a PC
Connect the Cisco 827 Router to a PC
Follow these steps to connect the Cisco 827 router to a PC:
Figure 2
TO HUB
TO PC
Connecting a Cisco 827 Router to a PC
ETHERN
ET
CONSO
LE
ADSL
Model Ci
sco 827-
4V
+5,+12,-
12,-24,-71
PHONE
1
4
, VDC
3
2
1
Cisco 827-4V router
OK
SER 0
AUX
LAN
AUX
PC
Step 1
Connect the yellow Ethernet cable from the yellow Ethernet port on the back panel of the router to the
Ethernet port on the NIC on the computer.
Step 2
Verify that the TO HUB/TO PC switch on the left side of the back panel has been set to the TO PC
position (out). If the button is in, press it to set it to the out position.
Connect the Cisco 827 Router to a PC
78-6853-03
3
Connect the Cisco 827 Router to a Hub
Connect the Cisco 827 Router to a Hub
Follow these steps to connect the Cisco 827 router to a hub:
Figure 3
TO HUB
TO PC
Connecting a Cisco 827 Router to a Hub
ETHERN
ET
CONSO
LE
ADSL
Model Ci
sco 827-
4V
4
Cisco 827-4V router
+5,+12,-
12,-24,-71
PHONE
1
, VDC
3
2
1
1X
2X
SPEED
LED
100Bas
eTX SO
LID
10Base
T BLI
NK
10/100
3X
4X
1 2 3
4
5 6 7
8
5X
6X
7X
8X
MDI
MDI-X
Cisco 1528 Micro Hub 10/100
Step 1
Connect the yellow Ethernet cable from the yellow Ethernet port on the back panel of the router to the
Ethernet port on the hub.
Step 2
Verify that the TO HUB/TO PC switch on the left side of the back panel has been set to the TO HUB
position (in). If the button is out, press it to set it to the in position.
Connect the Cisco 827 Router to a Hub
4
78-6853-03
Connect an ADSL Line
Connect an ADSL Line
Follow these steps to connect an ADSL line to the ADSL port on your router.
Note
The following instructions are for a straight-through ADSL cable, but they also apply if you are using
a crossover cable to connect your ADSL line. One ADSL cable is supplied with the Cisco 827 router,
and it is selected during the ordering process. If you have microfilters or do not have the phone
service on the same line, use the lavender CAB-ADSL-RJ11 cable. If you have a splitter installed,
use the lavender with blue stripe CAB-ADSL-RJ11X cable.
Figure 4
TO HUB
TO PC
Connecting a Cisco 827 Router to an ADSL Line
ETHERN
ET
CONSO
LE
ADSL
Model Ci
sco 827-
4V
+5,+12,-
12,-24,-71
PHONE
1
4
, VDC
3
2
1
Cisco 827-4V router
Wall jack
Step 1
Connect the lavender ADSL cable to the lavender ADSL port on the router.
Step 2
Connect the other end of the ADSL cable to the external wall jack.
Connect an ADSL Line
78-6853-03
5
Connect a Telephone or Fax Machine
Connect a Telephone or Fax Machine
If you have a Cisco 827-4V router, you can connect an analog telephone or fax machine to your router.
Use the cables provided with these devices.
The gray PHONE 4, 3, 2, and 1 ports are RJ-11 connectors. If you are outside of North America, you
must buy and attach adapters that allow your telephones or faxes to be connected to these RJ-11
connectors. In some countries, these adapters need additional electronics to convert the telephones or
faxes to work properly with the router phone ports. For example, in the United Kingdom, you must buy
an adapter that also provides a master socket, which causes incoming calls to ring the connected devices.
For information on recommended master sockets, see the Cisco 827 Routers Hardware Installation
Guide.
Caution
Do not connect the router telephone ports to the telephone wall jack. These ports are not meant for
direct connection to the public network. This connection can damage your router.
Figure 5
TO HUB
TO PC
Connecting a Telephone to a Cisco 827-4V Router
ETHERN
ET
CONSO
LE
ADSL
Model Ci
sco 827-
4V
Cisco 827-4V router
+5,+12,-
12,-24,-71
PHONE
1
4
, VDC
3
2
1
Analog telephone
Step 1
Connect one end of the telephone cable to the gray PHONE 4, 3, 2, or 1 port.
Step 2
Connect the other end of the cable to your device.
Connect a Telephone or Fax Machine
6
78-6853-03
Connect the Power and Turn On the Router
Connect the Power and Turn On the Router
Follow these steps to connect power to the Cisco 827 router and turn it on:
Figure 6
Connecting the Power to a Cisco 827 Router
TO HUB
TO PC
ETHERN
ET
Model Ci
CONSO
LE
ADSL
sco 827-
4V
+5,+12,-
12,-24,-71
PHONE
1
4
3
2
To electrical outlet
, VDC
1
8-pin connector
Desktop power supply
Step 1
Make sure the router power is off. Press the power switch to standby (
Step 2
Connect the power supply cable to the 8-pin connector on the router.
Step 3
Connect the socket end of the power cord to the desktop power supply.
Step 4
Connect the plug end of the power cord to an electrical outlet.
Step 5
Turn ON the router. Press the power switch to on (|).
).
Connect the Power and Turn On the Router
78-6853-03
7
Set Up the Router to Access the Network
Set Up the Router to Access the Network
The Cisco Router Web Setup (CRWS) software is already loaded on your Cisco 827 router. You can use
CRWS to configure the Cisco 827 router. If you purchased your router through an Internet service
provider (ISP), it is possible that your router has been configured for use at your site. If you know this
is not the case, or if you have purchased Cisco IOS software for the router since installing it, we
recommend that you use CRWS to configure the router.
Step 1
Log on to the PC connected to the router through the ETHERNET port.
Step 2
Open a web browser.
Step 3
Type in the following universal resource locator (URL):
http://10.10.10.1
Step 4
Click the Router Setup link in the Cisco Router Web Setup home page, and follow the instructions that
appear in the page that is displayed.
Step 5
If the CRWS home page does not appear when you enter the URL http://10.10.10.1, test the connection
between the PC and the router by doing the following:
a.
Check that the OK LED on the router is on, and check the cable connection between the router and
the PC. Be sure that the TO HUB/TO PC button is in the TO PC position.
b.
If the CRWS home page still does not appear, verify that your web browser’s work offline option is
disabled.
c.
If the web page still does not appear, verify that your PC is automatically configured to receive an
IP address, by following the instructions in Cisco Router Web Setup User Guide, which is available
on the Cisco Documentation CD-ROM.
Set Up the Router to Access the Network
8
78-6853-03
Verifying the LEDs
Verifying the LEDs
The following table describes the normal pattern for LEDs and what to do if you get an abnormal pattern.
For more information on all LEDs, see the Cisco 827 Routers Hardware Installation Guide.
LED
Normal
Pattern
OK
Explanation
If Abnormal Pattern
On
Power is supplied to
the router.
If off, see the Cisco 827 Routers
Hardware Installation Guide.
PHONE 1, 2, 3, 4
On
Telephone or fax
machine is
connected.
If off, see the Cisco 827 Routers
Hardware Installation Guide.
ADSL CD
On
ADSL line is
connected.
If off, see the Cisco 827 Routers
Hardware Installation Guide.
ADSL RXD
Blinks
ADSL port receives
data.
If off, see the Cisco 827 Routers
Hardware Installation Guide.
ADSL TXD
Blinks
ADSL port sends
data.
If off, see the Cisco 827 Routers
Hardware Installation Guide.
ETHERNET 1
On
Ethernet device is
connected.
If off, toggle TO HUB/TO PC button (if
set to TO HUB [in], reset to TO PC
[out] or vice versa). If still off, see the
Cisco 827 Routers Hardware
Installation Guide.
ETHERNET RXD Blinks
Ethernet port is
receiving a packet.
If off, see the Cisco 827 Routers
Hardware Installation Guide.
ETHERNET TXD Blinks
Ethernet port is
transmitting a
packet.
If off, see the Cisco 827 Routers
Hardware Installation Guide.
Verifying the LEDs
78-6853-03
9
About the Product CD
About the Product CD
The 800 and SOHO Series Product Documentation CD contains the technical publications for the 800
and SOHO series routers.
System Requirements
Processor
Pentium 150 MHz or faster recommended
PC OS
Microsoft Windows 95
Microsoft Windows 98
Microsoft Windows 2000
Microsoft Windows NT 4.0
Memory
64-MB DRAM
Drives
4x CD-ROM drive
Monitor
Color monitor capable of 800 x 600 pixel
resolution
Software
Netscape 3.0 or later
Internet Explorer 3.0 or later
Adobe Acrobat Reader 3.0 or later
Documentation Exceptions
This CD does not contain certain publications that were incomplete or unavailable when this CD was
produced. These documents are in the 800 and SOHO platform hardware accessory kits and should be
consulted before installing and configuring your system. You can also access these documents on the
Documentation page on Cisco Connection Online (CCO) at www.cisco.com.
•
Cisco 800 Series Routers Release Notes
•
Cisco 828 and SOHO 78 Routers Release Notes
•
IOS Release Notes for the Cisco 800 Series Router
•
IOS Release Notes for the Cisco 828 Router
•
Cisco Router Web Setup User Guide
About the Product CD
10
78-6853-03
About the Product CD
Using the CD Interface
When the CD is first launched, it automatically opens a browser session and displays the CD interface
in the browser window. You can use the list of books in the left pane of your display to navigate directly
to the book you want to view. Within the interface, you can use your mouse to:
•
Hover over book titles in the left column for an overview of the document before opening a
document.
•
Select a book title from the document list on the left or from the document drop-down menu on the
CD title bar.
•
Click the Cisco Systems corporate icon to display Cisco support and service information.
•
Click About This CD (notepad icon) to get additional information about this CD.
•
Click Send Us Your Feedback! (pencil & notepad icon) to provide us with your feedback.
•
Click Get Acrobat Reader to install a free copy of Adobe Acrobat Reader 4.0.
Changing the Display Properties of Documents
When you first launch the CD, you will notice a list of books in the left pane of your display that you
can use to navigate directly to the book you want to view. When you select the document, Acrobat
Reader opens the book in .pdf format and provides a list of topics in the left frame of the Acrobat
window. To disable this option and view the book fully in the window, click the Show/Hide Navigation
Pane button on the Acrobat toolbar. Note that when hiding bookmarks, the thumbnails, annotations, and
articles are also hidden.
Printing Documents
To print a document:
Step 1
Click the Printer icon on the Acrobat toolbar.
The Windows Print Dialog box appears.
Step 2
Select your default printer and click OK.
Ordering Printed Copies of Documents
You can order printed copies of the documents on this CD and additional copies of this CD on the 800
and SOHO platform product ordering pages on Cisco Connection Online (CCO). Registered CCO users
can order documentation for other Cisco products and the Cisco Documentation CD-ROM (containing
all Cisco documentation) through our online Subscription Services at
http://www.cisco.com/cgi-bin/subcat/kaojump.cgi.
Nonregistered CCO users can order documentation through a local account representative by calling
Cisco’s corporate headquarters (California, USA) at 408 526-4000 or, in North America, by calling
800 553-NETS (6387).
You can access the most current Cisco documentation on the World Wide Web at http://www.cisco.com,
http://www-china.cisco.com, or http://www-europe.cisco.com.
Using the CD Interface
78-6853-03
11
About the Product CD
AccessPath, AtmDirector, Browse with Me, CCIP, CCSI, CD-PAC, CiscoLink, the Cisco Powered Network logo, Cisco Systems Networking
Academy, the Cisco Systems Networking Academy logo, Fast Step, Follow Me Browsing, FormShare, FrameShare, GigaStack, IGX, Internet
Quotient, IP/VC, iQ Breakthrough, iQ Expertise, iQ FastTrack, the iQ Logo, iQ Net Readiness Scorecard, MGX, the Networkers logo, Packet,
RateMUX, ScriptBuilder, ScriptShare, SlideCast, SMARTnet, TransPath, Unity, Voice LAN, Wavelength Router, and WebViewer are trademarks
of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All That’s Possible, and Empowering the Internet Generation,
are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified
Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo,
Enterprise/Solver, EtherChannel, EtherSwitch, FastHub, FastSwitch, IOS, IP/TV, LightStream, MICA, Network Registrar, PIX, Post-Routing,
Pre-Routing, Registrar, StrataView Plus, Stratm, SwitchProbe, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. and/or its
affiliates in the U.S. and certain other countries.
All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (0108R)
Copyright © 2001, Cisco Systems, Inc.
All rights reserved.
Cisco 827 Router Cabling and Setup Quick Start Guide
12
78-6853-03
Download PDF

advertising