Motorola | D1104 | User guide | Motorola D1104 User guide

Motorola D1100 Series
For D1101, D1102, D1103 and D1104
Digital Cordless Phone
Warning
Use only rechargeable batteries.
Charge the handset for 24 hours before use.
Welcome...
EN
to your new Motorola D1100 Digital Cordless Phone!
• Wall mountable freedom base – all handsets fully cordless for
locating anywhere within range.
• 1.6” colour display.
• 100 Name and number phonebook.
• Copy phonebook entries between other handsets.
• Screensaver clock display.
1
You must subscribe to your network provider’s Caller Display or
Call Waiting service for these features to work. A quarterly fee may
be payable.
Please note that this equipment is not designed for making
emergency telephone calls when the power fails. Alternative
arrangements should be made for access to emergency.
• Caller Display shows you who’s calling and see details of the
last 30 callers in a Calls list.1
• Register up to 5 handsets to a single base and register each
handset with up to 4 different bases.
• Make internal calls, transfer external calls, hold 3-way
conversation between two internal callers and an external
caller.
This User Guide provides you with all the information
you need to get the most from your phone.
Before you make your first call you will need to set up your phone.
Follow the simple instructions in ‘Getting Started’, on the next few pages.
IMPORTANT
• 2 x AAA NiMH rechargeable batteries
Only use the telephone line cord supplied.
This equipment is not designed for making emergency telephone calls
when the power fails. Alternative arrangements should be made for
access to emergency services.
• Mains power adaptor for the base
• Telephone line cord
• Wall mounting screws and wall plugs
Got everything?
If you have purchased a D1100 multiple pack you will also
have the following additional items:
• D1100 handset
• D1100 handset & charger
• D1100 base
• 2 x AAA NiMH rechargeable batteries
• User guide
• Mains power adaptor for the charger
1.
2.
3.
4.
Getting started 4
Location 4
Setting up 4
Connecting up the large base 4
Connecting the handset and charger (Multi-pack only) 4
Setting up your D1100 5
Set date and time manually 5
Getting to know your phone 5
Overview of your handset 5
Handset Display 6
Display icons 6
Overview of the base 6
Menu map 7
Character map 8
Using the phone 8
Switch the handset on / off 8
Make a call 8
Preparatory dialling 8
End a call 8
Receive a call 8
Adjust the earpiece/receiver volume 8
Secrecy 8
Call another handset 9
Transfer a call 9
3-way conference call 9
Make a handsfree call 9
Answer a call in handsfree 9
Redial a number from the redial lists 9
Save a number from the redial list to the phonebook 9
Delete a redial number/delete all redial 9
To lock the keypad 9
Paging/Find handset 9
Store a name and number 9
Open the phonebook during a call. 10
View an entry 10
Dial an entry 10
Edit a name and number 10
Edit ringtone 10
Delete an entry 10
Delete entire phonebook 10
Copy an entry to another handset 10
Copy the entire phonebook to another handset 10
Fast call 10
Memory status 10
Handset settings 11
Handset ringtone 11
Handset ringer volume 11
Receiver volume 11
Handset name 11
Display language 11
Wallpaper 11
Menu colour 11
Screensaver 11
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Light timeout 11
Display contrast 11
Auto talk 11
Key beep 12
PABX access code 12
Base settings 12
Base ringtone 12
Base ringer volume 12
Dialling mode 12
Ring priority 12
Recall mode 12
First ring 12
System PIN 12
Restore default settings 13
Default settings 13
ECO mode 13
Clock & alarm 13
Date & time 13
Set alarm 13
Alarm on /off 13
Switch off alarm ring 14
Time format 14
Event Reminder 14
Add a new event 14
Switch off reminder ring 14
Show reminder details 14
Edit reminder 14
Delete reminder 14
Delete all reminders 14
Calls lists 15
Caller Display 15
Calls lists 15
New calls alert 15
View new missed calls 15
View and dial from a Calls list 15
Copy a Calls list number to the phonebook 15
Delete an entry 15
Delete all entries 15
Call Waiting 16
Voicemail 16
Room Monitor 16
To switch Room Monitor On 16
To change the monitor level 16
To set the dial out number 16
Using additional handsets 17
Registering an additional handset 17
Select a base 17
De-register a handset 17
Help 17
General information 18
Important safety instructions 18
Installation Guidelines 18
Battery Safety Instructions 18
Cleaning 19
Environmental 19
Product disposal instructions 19
Consumer Products and Accessories Warranty 19
R&TTE 20
Connecting to a switchboard 20
Inserting a pause 20
Recall 20
15. Wall mounting 20
3
EN
1. Getting started
WHICH POWER ADAPTOR?
WARNING
Do not place your D1100 in the bathroom or other humid areas.
The power adaptor with a clear connector is for the base unit
and the power adaptor with a red colour connector is for the
charger unit.
Location
Connecting up the large base
You need to place your D1100 base within 2 metres of the
mains power socket and telephone socket so that the cables
will reach.
IMPORTANT
Warning! Use only rechargeable batteries. If nonrechargeable batteries are used WRONG BATTERY will be
displayed and charging will be stopped. Please
replace with rechargable batteries.
BATTERY LOW WARNING
Make sure it is at least 1 metre away from other electrical
appliances to avoid interference. Your D1100 works by sending
radio signals between the handset and base. The strength of
the signal depends on where you place the base. Putting it as
high as possible ensures the best signal.
To wall mount your D1100 base, see “Wall mounting” on
page 20.
If the
icon shows a red segment in the display, you will
need to recharge the handset before you can use it again.
HANDSET RANGE
The D1100 has a range of up to 300 metres outdoors when
there is a clear line of sight between the base and handset. Any
obstruction between the base and handset will reduce the
range significantly. With the base indoors and handset either
indoors or outdoors, the range will normally be up to 50 metres.
Thick stone walls can severely affect the range.
SIGNAL STRENGTH
The
icon on your handset indicates when you are in range.
When out of range of the base, the screen shows Searching…
and the
flashes. During call, if the handset goes out of range
the handset will emit out out of range warning tone.
If you are on a call, the line will hang up if the handset moves
out of range of the base. Move back within in range. The
handset will automatically re-connect to the base.
Setting up
IMPORTANT
The base station must be plugged into the mains power at all
times. Do not connect the telephone line cord into the wall
socket until the handset is fully charged. Only use the power
and telephone cables supplied with the product.
4
2. Insert the 2 x AAA NiMH batteries supplied into the
handset. Then slide the compartment cover into place.
3. Place the handset on the charger to charge for at least 24
hours. When the handset is fully charged the
icon will
indicate that it is fully charged.
4. When the handset is fully charged after 24 hours, plug the
telephone line cord from the large base into the telephone
wall socket.
During charging, the
icon will scroll in the display.
BATTERY PERFORMANCE
Plug the power adapter with clear connector into the socket
marked
on the underside of the base and plug the other
end into the mains power wall socket and switch the power on.
Connecting the handset and charger
(Multi-pack only)
In ideal conditions, fully charged batteries should give up to 10
hours talk time or up to 100 hours standby time on a single
charge.
Note that new batteries do not reach full capacity until they
have been in normal use for several days.
To keep your batteries in the best condition, leave the handset
off the base for a few hours at a time.
If you have purchased a multiple pack, this process will need to
be carried out for all handsets and chargers:
Running the batteries right down at least once a week will help
them last as long as possible.
1. Plug the power adapter with red connector into the socket
marked
on the underside of the charger.
The charge capacity of rechargeable batteries will reduce with
time as they wear out, giving the handset less talk/standby
time. Eventually they will need to be replaced.
After charging your handset for the first time, subsequent
charging time is about 6–8 hours a day. Batteries and handset
may become warm during charging. This is normal.
Getting started
Setting up your D1100
Welcome screen
1. The Welcome screen will briefly appear, then a list of
countries is displayed.
2. Scroll u or d to your country (operator) and press Select .
The handset and base will reset to load the correct settings.
The standby screen is then displayed and your phone is
ready to use.
2. Getting to know your phone
Overview of your handset
You can still make and receive calls without first selecting your
country and network operator, however the Welcome screen
will re-appear until you have configured your phone country
settings.
Date and time
Providing you have subscribed to your network’s Caller Display
service, the date and time is set automatically for all handsets
when you receive your first call.
If you do not have a Caller Display service you can set the date
and time manually.
Set date and time manually
1. Press Menu and scroll u or d to Clock & Alarm then press
Select.
2. Date & Time is highlighted. Press Select.
3. Enter the date using the format DD/MM/YY e.g. 01 09 08
for 1st September 2008. Enter the time in 12 or 24 hour
time format. Press Save . To change the Time Format see
page 14.
4. Press > or Back until you return to standby.
D Option button (right)
In standby, press to open the phonebook menu, page 9.
Press to select options displayed on screen.
E Redial/ Up
In standby, press to open and scroll through the Redial list,
page 9.
In talk mode, press to adjust volume.
In menu mode, press to scroll through the options.
When storing an entry in the phonebook, press and hold to
enter a Pause, page 20.
F Talk/ Handsfree
In standby mode, press to make and receive calls, page 8.
In talk mode, press to switch handsfree on and off, page 9.
G End call/ Power on/off
Press to end a call, page 8.
In menu mode, press to return to standby.
In standby, press and hold to switch the handset off. When off,
press to switch the handset back on.
H Phonebook/ Down
In standby, press to open and scroll through the Names list,
page 10.
In talk mode, press to adjust volume.
In menu mode, press to scroll through the options.
I
Navigator glow ring
Illuminates when the phone is in use. Flashes to indicate new
event, eg. missed call.
J *
Press and hold to switch between Tone and Pulse dialling,
page 12
K #/ Lock
Press and hold to lock the keypad, page 9.
To unlock, select Unlock and follow the on screen instructions.
L Int (Intercom)
Used for internal calls, page 17.
M R (Recall)
For use with switchboard/PABX.
Your D1100 is now ready for use.
A Earpiece
B Display
See page 6 for an overview of the display icons.
C Option button (left)
Press to open the Menu.
Press to select options displayed on screen.
Getting to know your phone
5
EN
Handset Display
Range
indicator
Battery
status
Scrolls when
charging
The approximate power levels of your battery are indicated as
below:
Flashes
when out of
range or not
registered
Battery is fully charged.
Each menu has a list of options, which you can see on the
menu map on the following page.
Battery is partially charged.
When the handset is switched on and in standby:
Battery is running low.
1. Press Menu to open the main menu.
2. Then u use d or buttons to scroll through the available
options.
3. Press the Select option button to select a menu option or the
Back option button to go back to the previous screen.
To return to the previous menu level, press Back .
To exit the menu and return to standby, press >.
Battery is almost fully discharged (Red).
Handset
name/
number
* For this feature to work you must subscribe to your network
provider’s Caller Display service. A quarterly fee may be
payable.
NOTE
When the memory for voicemail messages is full, a white line
will appear below their corresponding reminder icon.
Display icons
Displayed in standby mode to indicate handset is in
range of the base.
Flashes if you move out of range.
B Navigating the menus
Your D1100 has an easy to use menu system.
If no buttons are pressed for 30 seconds, the handset returns
to standby automatically.
Overview of the base
Displayed if ECO Mode is switched on
Handset ringer volume is Off.
Displayed in handsfree talk mode.
An alarm is set.
The keypad is locked.
You have voicemail messages.*
You have missed calls.*
A Paging Key
In standby, press to ring the handset(s), page 9.
Press and hold to enter registration mode when registering
handsets, page 17.
6
Getting to know your phone
Menu map
Calls Lists
Reminder
Clock & Alarm
Settings
Registration
Extra
Names
Press Names during
a call:
Missed Calls
If there is an Event,
the following options
will be displayed.
Date & Time
Set Handset
Register Handset
Room Monitor
Received Calls
Alarm
Ringtone
Select Base
From menu in
standby:
Phonebook list
is displayed.
Dialled Calls
Add Event*
Time Format
Ringer Volume
De-register
Search
Select OPTIONS:
Delete Calls
Show Details
Receiver Volume
Edit Event
Handset Name
Delete Event
Language
Delete All Events
Wallpaper
Menu Colour
Add Entry
Add Entry
Copy Phonebook
Show Details
Memory Status
Edit Entry
Delete Phonebook
Delete Entry
Press d in standby:
Screensaver
Phonebook list
is displayed
Light Timeout
Select OPTIONS:
Display Contrast
Show Details
Auto Talk
Edit Entry
Key Beep
Copy Entry
PABX Access
Code
Ringtone
Set Base
Delete Entry
Fast Call
Ringtone
*If there is already an event on the list, "Event" is displayed.
Otherwise, "Add Event" is displayed.
Ringer Volume
Dialling Mode
Ring Priority
Recall Mode
First Ring
System PIN
Master Reset
ECO Mode
Getting to know your phone
7
EN
Character map
Key
Case
1
2
L/U*
3
4
5
6
7
8
9
0
*
#
Assigned characters and symbols
.
,
-
? !
¡
¿ '
L
a b c
U
A B C 2 Ä Æ Å Ç
L
d e f
U
D E F 3 É
L
g h i
4 ì
U
G H I
4
L
j
k l
5
U
J
K L 5
L
m n o 6 ö ø ò ñ
U
M N O 6 Ö Ø Ñ
L
p
U
P Q R S 7 Ş
L
t
U
T U V
8 Ü Û
L
w x y
z
U
W X Y Z 9
L/U
q r
u
@ :
;
/
1
2 ä æ å à ç
3 è é
s
3. Using the phone
Key
Case
CALL TIMER
1
2
L/U*
3
4
5
7 ş
v 8 ü û
9
0
L/U
bring up symbol table
L/U
short press to switch between Abc, abc,
ABC and 123 mode
*L = Lower
U = Upper
When display language is Türkçe - the character mapping is as
follow:
6
7
8
9
0
*
#
Assigned characters and symbols
.
,
-
? !
'
L
a b c 2 â ç
U
A B C 2 Â Ç
L
d e f
U
D E F 3
L
g h i
U
G H I
4 Ğ İ
L
j
k
5
U
J
K L 5
L
m n o 6 ö
U
M N O 6 Ö
L
p
U
P Q R S 7 Ş
L
t
l
q r
;
/
1
3
4 ğ õ
s
7 ş
u v 8 ü û
T U V 8 Ü Û
L
w x
U
W X Y Z 9
y z
9
0
L/U
bring up symbol table
L/U
short press to switch between upper and
lower case letters
*L = Lower
U = Upper
Your handset will automatically time the duration of all external
calls. The handset display shows the duration the phone is offhock both during and for a few seconds after your call.
Switch the handset on / off
1. In standby, press and hold > to switch the handset off.
When off, press > to switch back on.
Make a call
1. Press <.
2. When you hear the dial tone, dial the number.
Preparatory dialling
U
L/U
@ :
1. Dial the number first. If you make a mistake press Clear to
delete the last digit.
2. Press < to dial.
If the number dialled matches an entry in the phonebook, the
name is displayed.
End a call
1. Press >.
Receive a call
When you receive an external call, the phone rings. The display
shows External Call and the caller’s number or, if the number
matches an entry stored in the phonebook, the name is
displayed.
1. Press < to answer the call.
Adjust the earpiece/receiver volume
u d
1. During a call, press
or to increase or decrease the
volume. The display shows the level.
Secrecy
During a call, you can talk to someone nearby without your
caller hearing.
1. During a call, press Secrecy. The display shows Secrecy On
and your caller cannot hear you.
2. Press Off to return to your caller.
8
Using the phone
Internal calls
Call another handset
If you have more than one handset registered to the base, you
can make internal calls between two handsets.
1. Press I then the number (1-5) of the handset you want
to call.
2. Press OK to dial.
When an internal call is received, the display shows Internal Call
Handset X (where X is the calling handset) and the handset
number.
Transfer a call
You can transfer an external call to another handset registered
to the base.
During your call:
1. Press I then the handset number (1-5) you want.
2. Press OK to dial or press End to cancel the calls request and
return to the caller.
3. When the other handset answers you can announce the
caller.
4. Press > to complete the transfer or I to switch back
and forth between both callers.
If the other handset does not answer, press End to return to your
original caller.
3-way conference call
You can hold a 3-way conference call between 2 internal callers
and 1 external caller.
During a call to an external caller:
1. Press I then the handset number (1-5) you want.
2. Press OK to dial.
3. When the other handset answers you can announce the
caller.
4. Press Join to begin the conference call. Display shows
Conference Call .
5. Press > to hang up.
Handsfree
Handsfree lets you talk to your caller without holding the
handset. It also enables other people in the room to listen to
your conversation over the loudspeaker.
Using the phone
Make a handsfree call
<
1. Dial the number then press
.
2. Press
again. The
icon is displayed and you hear
your call over the handset loudspeaker.
3. Press
to switch the call between the earpiece and the
loudspeaker.
4. Press
to end the call.
During a handsfree call, press u or d to change the volume.
<
<
>
Answer a call in handsfree
When the phone rings, press < twice to answer in handsfree
talk mode.
Redial
The last 20 telephone numbers called are saved to a redial list.
You can then select any of the numbers to redial, delete or copy
to the phonebook.
Redial numbers can be up to 32 digits long.
Redial a number from the redial lists
1. Press u the last number you called is displayed.
2. Press u or d to scroll to the number you want.
3. Press < to dial.
Save a number from the redial list to
the phonebook
Please see “Copy a Calls list number to the phonebook” on
page 15 for instructions and select the Dialled Calls option.
Delete a redial number/delete all redial
Please see “Delete a redial number/delete all redial” on page 9
for instructions and select the Dialled Calls option.
To lock the keypad
You can lock the keypad so that it cannot be used accidentally
while carrying it around.
IMPORTANT
When the keypad is locked you can still answer incoming calls
and operate the handset as normal. When the call is ended, the
keypad lock comes on again.
1. Press and hold #.
is displayed. To unlock the
keypad:
2. Press Unlock . Display shows Press # to Unlock Keys.
3. Press #.
Paging/Find handset
You can alert a handset user that they are wanted or locate a
missing handset.
Paging calls cannot be answered by a handset.
1. Press p on the base. All handsets registered to the base
will ring and display Paging Call .
2. Press p on the base again to stop the ringing or, on any
handset, press Stop or any button on the handset to stop all
handsets ringing.
Phonebook
You can store up to 100 names and numbers in the phonebook.
Names can be up to 12 characters long and numbers up to 24
digits. You can also select different ring tones for phonebook
entries.
SEARCH ALPHABETICALLY
Press d
Or
Press Names.
Search is highlighted. Press Select.
The list of entries is displayed.
Enter the first letter of the name you want. The first name
beginning with that letter is displayed.
Scroll d to view any other entries beginning with that letter.
Store a name and number
If you subscribe to a Caller Display Service and want the name
of your caller displayed instead of the number, save the full
telephone number including the dialling code to your
phonebook.
You can store multiple entries with the same name but, to
prevent unnecessary duplicates, you can only store one
number once.
1. From standby, press Names . The phonebook menu is
displayed.
2. Search is highlighted. Scroll d to Add Entry and press Select.
3. Enter the name and press OK.
9
EN
When storing a name the first character is upper case and the rest
lower case.
To change the case manually, Press #.
To store a Pause in the number field, press and hold u.
To store a Recall in the number field, press R.
4. Enter the number and press Save .
5. Scroll u or d to the ringtone you want and press Select. The
display shows <NAME> Saved and returns to the phonebook
menu.
6. Press Back to return to the previous menu level or > to return
to standby.
ENTERING NAMES
Use the keypad letters to enter names, e.g. to store TOM:
Press 8 once to enter T.
Press 6 three times to enter O.
Press 6 once to enter M.
WRITING TIPS
Press Clear to delete the last character or digit.
Press u or d to move backwards or forwards through
character/digits.
Press # to switch between upper and lower case.
Press 0 to insert a space.
Use 1 for other punctuation characters.
You must enter a name to go with a number.
Open the phonebook during a call.
1. During your conversation, press Names.
2. Press Options to select Add Entry, Show Details, Edit Entry or
Delete Entry.
View an entry
1. Press d. The first entry is displayed.
2. Scroll u or d to the entry you want or search alphabetically.
3. Press Options. The display highlights Show Details .
4. Press Select to display the name, number and ringtone.
5. Press Dial to call the number or Back to return to the
previous level.
Dial an entry
1. In standby, press d. The first entry is displayed.
2. Scroll u or d to the entry you want or search alphabetically.
3. Press < to dial the displayed number.
10
Edit a name and number
1. Press d.
2. Scroll u or d to the entry you want.
3. Press Options and scroll d to Edit Entry and press Select .
4. Press Clear to delete characters, use the keypad to enter
new ones then press OK.
5. Press Clear to delete digits, use the keypad to enter new
ones then press Save.
6. Scroll u or d to the ringtone you want and press Select to
save the entry.
7. Press Back to return to the previous menu level.
Edit ringtone
1. Press d.
2. Scroll u or d to the entry you want.
3. Press Options and scroll d to Ringtone and press Select .
4. Scroll u or d to the ringtone you want or select Default
Melody and select Select.
5. Press Back to return to the previous menu level.
Delete an entry
1. Press d.
2. Scroll u or d to the entry you want.
3. Press Options and scroll d to Delete Entry and press Select.
4. Press Yes to confirm or No to cancel.
5. Press Back to return to standby.
Delete entire phonebook
1.
2.
3.
4.
Press Names.
Scroll u or d to Delete Phonebook and press Select.
Press Yes to confirm or No to cancel.
Press Back to return to standby.
Copy an entry to another handset
When you have more than one handset registered to your
D1100 base, you can copy entries between handsets.
Press d.
Scroll u or d to the entry you want.
Press Options and scroll d to Copy Entry and press Select .
To Handset is displayed. Press Select.
Available handsets are displayed. Scroll u or d to the
handset you want and press Select . Copy Phonebook? is
prompted on the receiving handset. Press Yes to accept or
No to cancel. When completed the sending handset
displays <NAME> Copied .
6. Press Back to return to the previous menu level.
1.
2.
3.
4.
5.
Copy the entire phonebook to another
handset
In just a few minutes, you can copy all your phonebook contacts
to another handset.
At the handset you are copying from:
Press Names .
Scroll d to Copy Phonebook and press Select .
To Handset is displayed. Press Select.
Available handsets are displayed. Scroll u or d to the
handset you want and press Select. When completed the
display shows the number of entries copied.
5. Press Back to return to the previous menu level.
1.
2.
3.
4.
At the receiving handset:
1. The display shows Copy Phonebook? Press Yes to begin
copying or No to cancel.
Fast call
Fast Call allows you to store phonebook and calls list entries
under keys 1, 2 and 3. You can then dial these numbers by
pressing and holding the appropriate key.
1. Press Names or d key. The names list will be displayed.
Select the entry you want to save as a Fast Call number
and press Options.
2. Scroll u or d to Fast Call and press Select.
3. Scroll u or d to KEY 1, KEY 2 or KEY 3 and press Select.
4. Press Assign to save the number.
5. If you want to clear the entry, press Clear Entry to delete the
number. The display will show Entry Cleared .
Memory status
You can check how much of the phonebook memory is
available.
1. Press Names .
2. Scroll d to Memory Status and press Select.
3. Display shows the number of Memory Used and Memory Free
entries.
4. Press Back to return to the previous menu level.
Using the phone
4. Handset settings
Handset ringtone
You can set different ringtones for external calls and internal
calls.
Select from 10 handset ringtones.
You will hear a sample ring for each one you highlight.
Press Menu, scroll d to Settings and press Select.
Set Handset is highlighted. Press Select.
Ringtone is highlighted. Press Select.
Press u or d to highlight External Call or Internal Call. Press
Select to confirm.
5. Scroll u or d to highlight the ringtone you want.
6. Press Select to confirm.
7. Press Back to return to the previous menu level or > to return
to standby.
1.
2.
3.
4.
5.
Press Menu, scroll d to Settings and press Select.
Set Handset is highlighted. Press Select .
Scroll d to Handset Name and press Select.
Use the keypad to enter the name and press Save.
Press Back to return to the previous menu level or > to return
to standby.
Display language
The available languages include:
1.
2.
3.
4.
English, Français, Deutsch, Italiano, Español, Nederlands,
Åëëçíéêá, Português and Türkçe.
Handset ringer volume
Wallpaper
The handset has 5 ringer volume settings plus Off.
If the volume is set to Off the
icon is displayed.
Press Menu, scroll d to Settings and press Select.
Set Handset is highlighted. Press Select.
Scroll d to Ringer Volume and press Select.
Press u or d to display the volume level you want. Press
Save to confirm.
5. Press Back to return to the previous menu level or > to return
to standby.
1.
2.
3.
4.
Receiver volume
This sets the standard volume level for the handset earpiece.
There are 8 levels to choose from.
Press Menu, scroll d to Settings and press Select.
Set Handset is highlighted. Press Select.
Scroll d to Receiver Volume and press Select.
Press u or d to display the volume level you want. Press
Save to confirm.
5. Press Back to return to the previous menu level or > to return
to standby.
1.
2.
3.
4.
Handset name
If you are using more than one handset with your D1100 base, you
can give each handset a personalised name to easily distinguish
between the handsets.
1.
2.
3.
4.
5.
Press Menu, scroll d to Settings and press Select.
Set Handset is highlighted. Press Select.
Scroll u to d Language and press Select .
Scroll d or to the language you want and press Select .
Press Back to return to the previous menu level or > to return
to standby.
Press Menu, scroll d to Settings and press Select.
Set Handset is highlighted. Press Select.
Scroll d to Wallpaper and press Select .
Scroll u or d to the wallpaper you want and press View.
On the preview screen, scroll u or d to see available
wallpapers.
6. Press Use to confirm the wallpaper.
7. Press Back to return to the previous menu level or > to return
to standby.
1.
2.
3.
4.
5.
Menu colour
Press Menu, scroll d to Settings and press Select.
Set Handset is highlighted. Press Select.
Scroll d to Menu Colour and press Select .
Scroll u or d to select the colour you want: blue, orange or
pink and press Select.
5. Press Back to return to the previous menu level or > to return
to standby.
1.
2.
3.
4.
Screensaver
1.
2.
3.
4.
5.
6.
Press Menu, scroll d to Settings and press Select .
Set Handset is highlighted. Press Select .
Scroll d to Screensaver and press Select .
Scroll u or d to set the Screensaver to Clock or Off .
Press Select to select Clock .
Press Back to return to the previous menu level or > to return
to standby.
Light timeout
Set how long the backlight stays on after the handset has
returned to standby screen.
Press Menu, scroll d to Settings and press Select .
Set Handset is highlighted. Press Select .
Scroll d to Light Timeout and press Select .
Scroll u or d to set the timeout period you want then press
Select.
5. Press Back to return to the previous menu level or > to return
to standby.
1.
2.
3.
4.
Display contrast
1. Press Menu, scroll d to Settings and press Select .
2.
3.
4.
5.
Set Handset is highlighted. Press Select .
Scroll d to Display Contrast and press Select.
Scroll u or d to Low, Medium or High then press Select .
Press Back to return to the previous menu level or > to return
to standby.
Auto talk
If you set Auto Talk to ON, when you receive an incoming call you
can answer it just by lifting your handset from the charger. You do
not need to press <.
1.
2.
3.
4.
5.
Press Menu, scroll d to Settings and press Select .
Set Handset is highlighted. Press Select .
Scroll d to Auto Talk and press Select .
Scroll u or d to On or Off then press Select .
Press Back to return to the previous menu level or > to return
to standby.
When the screensaver is set to Clock an analogue clock is
displayed.
The screensaver comes on when the screen backlight switches
off in standby mode. To change the backlight timeout setting,
see Light timeout.
A name can be up to 10 characters long.
Handset settings
11
EN
Key beep
When you press a button on the D1100 handset you hear a
beep. You can switch this on or off.
1.
2.
3.
4.
5.
Press Menu, scroll d to Settings and press Select .
Set Handset is highlighted. Press Select.
Scroll d to Key Beep and press Select .
Scroll u or d to Off or On then press Select.
Press Back to return to the previous menu level or > to return
to standby.
PABX access code
If your D1100 is connected to a switchboard, you may need to
enter a one-digit access code in the dialling sequence to be
able to connect to the outside line.
The access code will be displayed at the beginning of a number
on the screen.
The access code will not be used when you dial the number
yourself (rather than for example from the phonebook). This
allows you to make calls to other switchboard extensions.
Press Menu, scroll d to Settings and press Select .
Set Handset is highlighted. Press Select.
Scroll d to PABX Access Code and press Select .
Scroll u or d to On , Off or Set Code then press Select .
If you select Set Code, enter the switchboard access code
e.g. 9 then press Save.
5. Press Back to return to the previous menu level or > to return
to standby.
1.
2.
3.
4.
5. Base settings
Base ringtone
If you choose Select Handset all available handsets are
displayed. Scroll u or d to highlight the handset you want
then press Select .
Select from 5 base ringtones.
You will hear a sample ring for each one you highlight.
1.
2.
3.
4.
5.
6.
Press Menu, scroll d to Settings and press Select.
Scroll d to Set Base and press Select .
Ringtone is highlighted. Press Select.
Scroll u or d highlight the ringtone you want.
Press Select to confirm.
Press Back to return to the previous menu level or > to return
to standby.
Base ringer volume
The base has 5 ringer volume settings plus Off.
Press Menu, scroll d to Settings and press Select.
Scroll d to Set Base and press Select .
Scroll d to Ringer Volume and press Select .
Press u or d to display the volume level you want. Press
Select to confirm.
5. Press Back to return to the previous menu level or > to return
to standby.
1.
2.
3.
4.
Dialling mode
Your D1100 is pre-set to Tone dialling. You should not normally need
to change this setting. The dial mode options are Tone or Pulse.
Press Menu, scroll d to Settings and press Select.
Scroll d to Set Base and press Select .
Scroll d to Dialling Mode and press Select .
Press u or d to highlight Pulse or Tone then press Select to
confirm.
5. Press Back to return to the previous menu level or > to return
to standby.
1.
2.
3.
4.
Ring priority
When you have more than one handset registered to your
base, you can set one handset to ring before the other
handsets. This allows one handset user to answer all incoming
first, like a receptionist.
Choose All Handsets if you want all handsets to ring at the same
time or Select Handset to nominate a handset to ring two times
before the others.
1. Press Menu, scroll d to Settings and press Select.
2. Scroll d to Set Base and press Select .
3. Scroll d to Ring Priority and press Select .
12
4. Press u or d to highlight All Handsets or Select Handset then press
Select.
Scroll u or d to the number of rings you want to set 2, 4 or
6 and press Select.
5. Press Back to return to the previous menu level or > to return
to standby.
Recall mode
Press Menu, scroll d to Settings and press Select.
Scroll d to Set Base and press Select .
Scroll d to Recall Mode and press Select .
Press u or d to highlight Recall 1 or Recall 2 then press Select to
confirm.
5. Press Back to return to the previous menu level or > to return
to standby.
1.
2.
3.
4.
First ring
If you have subscribed to your network’s Caller Display service, your
D1100 does not ring until the caller information has been received
and displayed.
However, if you want your handset to ring without waiting for
the caller information to be displayed, set First Ring to On.
Please note that this will mean the first ring you hear will be the
default ringtone. This will change to any ringtone you have set
once the caller information is displayed.
1.
2.
3.
4.
5.
Press Menu, scroll d to Settings and press Select.
Scroll d to Set Base and press Select .
Scroll d to First Ring and press Select .
Press u or d to On or Off then press Select to confirm.
Press Back to return to the previous menu level or > to return
to standby.
System PIN
The System PIN is used when changing certain settings and
registration / de-registration. The default setting is 0000. You
can change this to your own preferred number up to 8 digits.
When you enter a PIN the digits are shown as ****.
1.
2.
3.
4.
5.
Press Menu, scroll d to Settings and press Select.
Scroll d to Set Base and press Select .
Scroll d to System PIN and press Select .
Enter the old PIN (original setting 0000) and press OK.
Enter the new PIN and press OK.
Base settings
6. Re-enter the new PIN and press OK .
7. Press Back to return to the previous menu level or > to return
to standby.
Restore default settings
You can restore your D1100 to its default (original) settings.
It will not affect the phonebook, calls list or user’s data.
All handsets registered to the base will be retained. All handset
and base settings will be reset.
1.
2.
3.
4.
5.
Press Menu, scroll d to Settings and press Select.
Scroll d to Set Base and press Select .
Scroll d to Master Reset and press Select .
Select Yes to confirm or No to cancel.
Enter the system PIN (original setting 0000) then press OK.
The display will show Reset Compete and the unit will restart.
Default settings
Handset Name
Handset
Handset External Ringtone
Melody 3
Handset Internal Ringtone
Melody 1
Handset Ring Volume
3
Receiver Volume
4
Key Beep
On
Auto Talk
On
Screensaver
Clock
Base Ringtone
Melody 1
Base Ring Volume
3
Dialling Mode
Tone
First Ring
Off
System PIN
0000
ECO Mode
Off
Room Monitor
Off
Clock & alarm
ECO mode
To reduce the level of power emissions, you can select low
power or ECO mode. When the ECO mode is set to On, the
base transmission power will be reduced.
To turn ECO Mode to On or Off :
1.
2.
3.
4.
Press Menu, scroll d to Settings and press Select.
Scroll d to Set Base and press Select .
Scroll d to ECO Mode and press Select .
Press u or d to highlight On or Off then press Select to
confirm.
The display will show Set to ON or Set to OFF depending on the
selection together with a confirmation tone.
6. Clock & alarm
Date & time
If you subscribe to your network’s caller display service, the
base sets the date and time for all handsets whenever a call is
received. You can manually set the time on an individual
handset.
1.
2.
3.
4.
5.
Press Menu, scroll d to Clock & Alarm and press Select .
Date & Time is highlighted, press Select.
Enter the date using the format DD/MM/YY.
Enter the time and press Save .
Press Back to return to the previous menu level or > to
return to standby.
Set alarm
Signal icon in
ECO mode
When the alarm is set, the display shows the
icon.
Each handset can have a different alarm setting.
Press Menu, scroll d to Clock & Alarm and press Select .
Scroll d to Alarm and press Select .
Press u or d to select On and press Select .
Press u or d to select Once, Monday-Friday or On Daily and
press Select .
5. Enter the time you want the alarm and press Save.
6. Press Back to return to the previous menu level or > to
return to standby.
will disappear from the
If the alarm was set to Once, the
screen.
1.
2.
3.
4.
When set to ON,
signal icon.
NOTE
icon is displayed in place of the standard
When ECO mode is set to ON, the handset range will be
reduced.
If set to On Daily or Monday-Friday, the
screen.
will remain on the
Alarm on /off
Once an alarm has been set, you can switch the setting On or
Off.
1.
2.
3.
4.
Press Menu, scroll d to Clock & Alarm and press Select .
Scroll d to Alarm and press Select .
Press u or d to select On or Off and press Select .
Press Back to return to the previous menu level.
13
EN
Switch off alarm ring
When the alarm goes off, press Stop.
If you are using the handset to make a call when the alarm ring
is due, the
flashes and you hear a beep in the earpiece.
Time format
Set the time format to 12 or 24 hour setting.
1.
2.
3.
4.
Press Menu, scroll d to Clock & Alarm and press Select .
Scroll d to Time Format and press Select .
Press u or d to select 12 Hour or 24 Hour and press Select .
Press Back to return to the previous menu level.
7. Event Reminder
Add a new event
Use your D1100 to remind you of details of up to five events
such as birthdays, anniversaries or appointments. The entry
can be up to 24 characters long.
Up to 24 characters can be entered as the subject.
1. Press Menu, scroll d to Reminder and press Select .
2. If no previous event is stored, Add Event is highlighted. Press
Select.
Or
If events are already stored, they are listed. Press Options.
Add Event is highlighted. Press Select.
3. Enter the subject and press Save .
4. Enter the date (DD/MM).
5. Enter the time (HH:MM) and press Save . If the current time
format setting is 12 hour, select am or pm.
6. Press u or d to select Silent or Alarm and press Select .
If you press Alarm:
Scroll u or d to select Once or Annually and press Select .
If Once is selected, scroll u or d to select when you want to
receive the reminder At event time or 30 min before . Press Select .
Display shows Saved .
If Annually is selected, then the alarm will sound at the
event’s time.
7. Press Back to return to the previous menu level or > to
return to standby.
If you select a silent reminder, the event subject is displayed on
screen but no alarm will sound.
When the event memory is full, the display shows Memory Full .
You must delete an event before you can add a new one.
Switch off reminder ring
Edit reminder
1. Press Menu, scroll d to Reminder and press Select .
2. Stored events are displayed. If required, scroll d to the
event you want and press Options.
Scroll d to Edit Event and press Select.
Edit the subject and press Save.
Edit the date and time then press Save .
Press u or d to select Silent or Alarm and press Select .
If you press Alarm:
Scroll u or d to select Once or Annually and press Select.
If Once is selected, scroll u or d to select when you want to
receive the reminder At event time or 30 min before. Press Select .
Display shows Saved.
If Annually is selected, then the alarm will sound at the
event’s time.
7. Press Back to return to the previous menu level or > to
return to standby.
3.
4.
5.
6.
Delete reminder
1. Press Menu, scroll d to Reminder and press Select .
2. Stored events are displayed. Scroll d to the event you want
and press Options.
3. Scroll d to Delete Event and press Select .
4. Press Yes to confirm or No to cancel.
5. Press Back to return to the previous menu level or > to return
to standby.
Delete all reminders
1. Press Menu, scroll d to Reminder and press Select .
2.
3.
4.
5.
Stored events are displayed. Press Options.
Scroll d to Delete All Events and press Select.
Press Yes to confirm or No to cancel.
Press Back to return to the previous menu level or > to return
to standby.
1. The event is displayed. Press View to stop the alarm and see
the details of the event. Or press Back to stop the alarm and
return to the standby screen. If no button is pressed, the alarm
stops after one minute.
Show reminder details
1. Press Menu, scroll d to Reminder and press Select .
2. Stored events are displayed. If required, scroll d to the
event you want and press Options .
3. Scroll d to Show Details and press Select . The description,
date and time of the reminder are displayed.
4. Press Back to return to the previous menu level or > to return
to standby.
14
Event Reminder
8. Calls lists
IMPORTANT
To use Caller Display you must first subscribe to the service
from your network provider. A quarterly fee may be payable.
To ensure the caller's name is displayed, make sure you have
stored the full telephone number, including the dialling code in
the phonebook.
If the caller’s number is stored in the phonebook, the name
assigned to it is displayed.
If the number is unavailable, Unavailable will be displayed.
If the call is from an international number, International will be
displayed.
If the call is from the operator, Operator will be displayed.
View and dial from a Calls list
1. Press Menu, scroll d to Calls Lists and press Select. Missed Calls
is highlighted. Scroll u or d to choose Missed Calls, Received
Calls or Dialled Calls.
2. Press Select . You can now scroll u or d through the list.
3. Press Options . Show Details is highlighted.
4. Press Select to see the caller’s number, date and time of
call.
5. Press Dial to call the number.
6. Press Back to return to the previous menu level or > to
return to standby.
Copy a Calls list number to the
phonebook
1. Press Menu, scroll d to Calls Lists then press Select. Missed
If you have subscribed to a Caller Display Service, you will be
able to see your caller’s number on your handset display
(provided it is not withheld) prior to answering the call.
If your caller’s name and number are stored in the phonebook
and a name/number match is found, you will see the caller’s
name on the display instead.
5. Scroll u or d to the ringtone you want and press Select .
6. Press Back to return to the previous menu level or > to
return to standby.
Calls lists
See “Entering names” and “Writing tips” on page 10.
If the call is from a ringback request, Ringback will be displayed.
Caller Display
Each handset can hold details of up to 30 answered or
unanswered calls and 20 dialled calls.
The caller’s details are stored in a Calls list whether you
answered the call or not. When the list is full, and a new call is
received, the oldest entry will be deleted automatically.
New calls alert
When you have missed calls, the display shows You have X new
missed calls. If you press Back , the screen returns to standby and
the
icon is displayed.
You can delete all entries in an individual Calls list or all entries
from all Calls lists.
1. Press Menu, scroll d to Calls List then press Select. Missed Calls
is highlighted.
If required, scroll u or d to Delete Calls press Select .
2. Scroll u or d to highlight Missed Calls, Received Calls, Dialled
Calls or All Calls. Press Select.
3. Press Yes to confirm or No to cancel.
4. Press Back to return to the previous menu level or > to
return to standby.
Calls is highlighted.
If required, scroll u or d to Received or Dialled Calls then press
Select.
2. Scroll u or d to the entry you want and press Options.
3. Scroll d to Save Number. Press Select.
4. Enter a name then press OK . The number is displayed,
press Save .
If you need to edit the number, use Clear to delete any unwanted
digits, then enter new ones using the keypad.
If the call is from a payphone, Payphone will be displayed.
Delete all entries
Delete an entry
1. Press Menu, scroll d to Calls Lists then press Select. Missed
Calls is highlighted.
If required, scroll u or d to Received or Dialled Calls then press
Select.
2. Scroll u or d to the entry you want and press Options.
3. Scroll d to Delete Call . Press Select .
4. Press Back to return to the previous menu level or > to
return to standby.
View new missed calls
1. When you see the new calls alert, press View. You can now
scroll u or d through the Missed Calls list.
2. Press Options. Show Details is highlighted. Press Select to see
the number, date and time of the call.
3. Press Back to return to the previous menu level or > to
return to standby.
Calls lists
15
EN
9. Call Waiting
11. Room Monitor
NOTE
You must subscribe to your network’s Caller Display service for
Call Waiting to work. A quarterly fee may be payable.
You can use your D1100 handset to monitor the sounds in
another room. If the sounds reach a certain level the handset
will automatically dial out to a preset external number or to
another handset. When the Room Monitor is set to On , the
handset will display Room Monitor On and only the microphone will
be active to monitor the sound levels in the room. Both the
speaker and receiver will be set to Off and the handset will not
ring if there’s any incoming call.
NOTE
1. During a call, you hear a soft beep in the earpiece and the
display shows the number of the caller or the name if it
matches an entry in your phonebook. If these are not
available, the display shows Call Waiting .
2. Press R to put your current caller on hold and speak to
the new caller.
3. Press R again to switch between both callers (In some
countries, it is required to dial R + 2).
4. Press > to finish the current call or > to end both calls.
10. Voicemail
If you have subscribed to your network operator’s voicemail
messaging service, your handset can inform you when you
receive new voicemail.
If you have new voicemail, You have new voicemail is displayed.
• Press Listen to dial the voicemail number preset on the
handset. If your voicemail number is different to the number
stored in the handset, you can manually dial your preferred
voicemail number.
• Or press Back to listen to your voicemail at a later time. A
reminder icon
will be displayed.
To switch Room Monitor On
1. Press Menu , scroll d to Extra then press Select . Room Monitor is
highlighted. Press Select. Mode will be highlighted.
2. Press Select, scroll d to On then press Select. Set to ON is
displayed for 2 seconds. The handset returns to idle screen
and disply as Room Monitor On.
To switch off Room Monitor press Off.
If only one handset is registered the display prompts "Not
available" and returns to the previous screen. You must register
additional handsets before the handsets will be displayed and
make Internal calls.
If the Room Monitor is triggered to call a handset or number and
the called handset is on a call, an alert tone of 3 beeps will be
heard. If the Room Monitor is triggered continuously the alert
beap will be emiitted every 5 seconds.
WARNING
This product is not intended for use as a baby safety device and
is not a substitute for adult supervision.
To change the monitor level
The monitor level can be set to High or Low, the default setting
is "Low".
To increase the sensitivity of the Room Monitor:
1. Press Menu , scroll d to Level , press Select and scroll u or d to
select Low or High setting.
To set the dial out number
1. Press Menu, scroll d to Call to and press Select .
2. Use the u or d key to select External or Internal .
External
1. Press Select and Enter Number: prompt will be displayed.
2. Enter the number and press Save . Saved will be displayed.
When Room Monitor is switched on and the sound level
reaches a certain level the number will be automatically
dialled.
Internal
1. Press Select and the registered handset will be listed, for
example "Handset 2".
2. Scroll u or d to select the handset the Room Monitor will call
if the noise levels reach a certain level.
3. Press Select and Set to handset 2 is displayed.
16
Call Waiting
12. Using additional handsets
You can use up to five D1100 additional handsets with your
D1100 base to extend your phone system without needing to
install extension sockets for each new phone.
Your D1100 handset can also be registered to up to 3 other
bases. You can then select the base you would prefer to use.
If you have purchased a D1100 multiple pack any additional
handsets come pre-registered to the base.
If you have purchased an additional handset separately you
must register it to your D1100 base before it can be used.
Registering an additional handset
At the base:
1. Press and hold p for 2 seconds until the base Power
starts flashing. The base will remain in registration mode for
90 seconds.
At the handset:
1. If the handset is new and the display shows Please Register.
Press Menu. Scroll u to Registration. Press Select.
Or
If the handset has already been registered to another base
the standby display is shown. Press Menu, scroll u or d to
Registration and press Select.
2. Register Handset is highlighted. Press Select.
3. Bases are displayed. If necessary, scroll u or d to a new
base you wish to register your D1100 handset to and press
Select.
4. Enter the system PIN and press OK. (Default setting =
0000)
5. The display shows Searching Base X (where X is the chosen
base number) then Handset Registered .
The handset is automatically assigned the next available
handset number.
If registration is not successful first time, please repeat the
process again in case the base registration period ran out of
time.
If there are already 5 handsets registered to the base, the
registration will fail. You must de-register another handset before
you can register the new one.
Select a base
If your D1100 handset is registered to more than one base, you
can select which base to use.
1. Press Menu, scroll u or d to Registration and press Select .
2. Scroll d to Select Base and press Select.
3. All base numbers are displayed. (In use) is added to bases
where the handset was previously registered to. Scroll u or
d to the base you want and press Select.
4. Display shows Searching Base…. then the standby display for
that base.
De-register a handset
Use one handset to de-register another. You cannot de-register
the handset you are using.
1. Press Menu, scroll u or d to Registration and press Select .
2. Scroll d to De-register and press Select .
3. Enter the system PIN and press OK. (Default setting =
0000)
4. Scroll u or d to the handset you want to de-register and
press Select .
5. Press Yes to confirm or No to cancel.
6. Press Back to return to the previous menu level or > to
return to standby.
13. Help
Phone does not work
• Have you installed the batteries correctly?
• Check that the mains power is correctly connected.
No dial tone
• Is the telephone cord of the base plugged into the phone
socket?
• Check that the mains power is correctly connected to the
base and to the handset charger(s).
• Only use the telephone cord supplied with the phone.
Cannot dial out or receive calls
• Check that the mains power is correctly connected.
• The batteries may need recharging.
• Has there been a power cut? If so, place the handset back on
the base for 10 seconds and try again. If it still does not work
disconnect the batteries and mains power for 10 minutes, then
reconnect and try again.
You have a dial tone, but the phone will not dial out
• You may need to change the dial mode from tone to pulse,
see page 12.
• If you are connected to a switchboard, check whether you
need to dial an access code.
Handset does not ring
•
•
•
•
The ringer volume may be switched off, see page 11.
Check that the mains power is correctly connected.
Check that the line cord is connected.
Make sure the handset is registered to the base, see
page 17.
No display
• The batteries may be flat, dead or incorrectly inserted.
Recharge or replace the batteries.
•
•
•
•
icon flashes
Is the handset registered correctly to the base, see page 17.
Check that the mains power is correctly connected.
Check that the handset is within range of the base.
The batteries are low, place the handset on the base/
charger to recharge.
icon not scrolling
• Try cleaning the charging contacts.
• Check that the mains power is correctly connected.
Using additional handsets
17
EN
You hear the busy tone when you press <.
• Make sure the handset is in range of the base.
• Another handset registered to your D1100 base may be on
the line.
No Caller Display number/name displayed
• Have you subscribed to a Caller Display service from your
network provider? See page 15.
• The caller may have withheld their number.
• An exact name/number match was not found in your
directory. Check that you have stored the full STD dialling
code.
Cannot register a handset to a base
• You can register a total of 5 handsets to your D1100 base
and you can register your D1100 handset to up to 4 bases.
Check that you have not exceeded the limits.
• Check that you have entered the correct PIN number
(default PIN 0000).
• Check that you are at least one metre away from other
electrical equipment to avoid interference when registering.
Base unit does not ring
• Have you connected the telephone line correctly?
• Is the base ringer set to off?
• You may have a faulty line or socket. Try using another
socket or line.
Buzzing noise on my phone or on other electrical
equipment nearby
• Sometimes your D1100 can interfere with other electrical
equipment if it is placed too close. It is recommended that
you place your D1100 at least one metre away from
electrical appliances or metal obstructions to avoid any risk
of interference.
• s in this user guide.
14. General information
IMPORTANT
This equipment is not designed for making emergency
telephone calls when the power fails. Alternative arrangements
should be made for access to emergency services.
This product is intended for connection to analogue public
switched telephone networks and private switchboards in
Vietnam.
Important safety instructions
Follow these safety precautions when using your phone to
reduce the risk of fire, electric shock, and injury to persons or
property:
1. Keep all slits and openings of the phone unblocked. Do not
set the phone on a heating register or over a radiator.
Ensure that proper ventilation is provided at the installation
site.
2. Do not use while wet or while standing in water.
3. Do not use this product near water (for example, near a
bath tub, kitchen sink, or swimming pool).
4. Do not allow anything to rest on the power cord. Place the
power cord so that it will not be walked on.
5. Never insert objects of any kind into the product vents as
that may result in fire or electric shock.
6. Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
7. Do not disassemble this product. If service or repair work is
required, contact the customer service helpline found in this
user's Guide.
8. Do not overload wall outlets and extension cords.
9. Avoid using during an electrical storm. Use a surge
protector to protect the equipment.
10. Do not use this phone to report a gas leak, especially if you
are in the vicinity of the gas line.
CAUTION
To reduce the risk of fire, use only the supplied power adaptor.
Unplug this cordless phone immediately from an
outlet if:
• The power cord or plug is damaged or frayed.
• Liquid has been spilled on the product.
• The product has been exposed to rain or water. Do not
retrieve the handset or base until after you have unplugged
the power and phone from the wall. Then retrieve the unit by
the unplugged cords.
18
• The product has been dropped or the cabinet has been
damaged.
• The product exhibits a distinct change in performance.
Installation Guidelines
1. Read and understand all instructions and save them for
future reference.
2. Follow all warnings and instructions marked on the product.
3. Do not install this product near a bath tub, sink, or shower.
4. Operate this phone using only the power source that is
indicated on the marking label. If you are unsure of the
power supply to your home, consult with your dealer or
local power company.
5. Do not place this product on an unstable cart, stand, or
table. This product may fall, causing serious damage to the
product.
6. Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls may
result in damage and will often require extensive work to
restore the product to normal operation.
7. Clean this product with a soft, damp cloth. Do not use
chemicals or cleaning agents to clean this phone.
8. Use only the power supply that came with this unit. Using
other power supplies may damage the unit.
9. Because this phone operates on electricity, you should have
at least one phone in your home that could operate without
electricity in the case the power in your home goes out.
10. To avoid interference to nearby appliances, do not place the
base of the phone on or near a TV, microwave oven, or VCR.
Battery Safety Instructions
• Do not burn, disassemble, mutilate, or puncture the battery.
The battery contains toxic materials that could be released,
resulting in injury.
CAUTION
• There is a risk of explosion if you replace the battery with an
incorrect battery type. Use only the battery pack that came
with your phone or an authorized replacement
recommended by the manufacturer.
• Keep battery packs out of the reach of children.
• Remove battery packs if storing over 30 days.
• Do not dispose of battery packs in fire, which could result in
explosion.
• The rechargeable battery packs that power this product
must be disposed of properly and may need to be recycled.
Refer to your battery’s label for battery type. Contact your
local recycling center for proper disposal methods.
SAVE THESE INSTRUCTIONS
General information
Cleaning
• Clean the handset and base (or charger) with a damp (not
wet) cloth, or an anti-static wipe.
• Never use household polish as this will damage the product.
Never use a dry cloth as this may cause a static shock.
Environmental
• Do not expose to direct sunlight.
• The handset may become warm when the batteries are
being charged or during prolonged periods of use. This is
normal. However, we recommend that to avoid damage you
do not place the product on antique/veneered wood.
• Do not stand your product on carpets or other surfaces
which generate fibres, or place it in locations preventing the
free flow of air over its surfaces.
• Do not submerge any part of your product in water and do
not use it in damp or humid conditions, such as bathrooms.
• Do not expose your product to fire, explosive or other
hazardous conditions.
• There is a slight chance your phone could be damaged by
an electrical storm. We recommend that you unplug the
power and telephone line cord during an electrical storm.
Product disposal instructions
Product disposal instructions for
residential users
When you have no further use for it, please remove any
batteries and dispose of them and the product per your local
authority’s recycling processes. For more information please
contact your local authority or the retailer where the product
was purchased.
Product disposal instructions for business
users
Business users should contact their suppliers and check the
terms and conditions of the purchase contract and ensure that
this product is not mixed with other commercial waste for
disposal.
Consumer Products and Accessories
Warranty
Thank you for purchasing this Motorola branded product
manufactured under license by Suncorp Technologies Limited,
3001-3005 China Resources Building, 26 Harbour Road, Wan
Chai, Hong Kong. ("Suncorp")
General information
What Does this Warranty Cover?
Subject to the exclusions contained below, SUNCORP
TECHNOLOGIES LTD. warrants that this Motorola branded
product ("Product") or certified accessory ("Accessory") sold for
use with this product that it manufactured to be free from
defects in materials and workmanship under normal consumer
usage for the period outlined below. This Limited Warranty is
your exclusive warranty and is not transferable.
Who is covered?
This warranty extends only to the first consumer purchaser, and
is not transferable.
What will SUNCORP TECHNOLOGIES LTD
do?
SUNCORP TECHNOLOGIES LTD or its authorized distributor
at its option and within a commercially reasonable time, will at
no charge repair or replace any Products or Accessories that
does not conform to this limited warranty. We may use
functionally equivalent reconditioned/ refurbished/ pre-owned
or new Products, Accessories or parts.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY, OTHERWISE THE REPAIR OR
REPLACEMENT PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT
SHALL MOTOROLA OR SUNCORP TECHNOLOGIES LTD
BE LIABLE, WHETHER IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF
THE PURCHASE PRICE OF THE PRODUCT OR
ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND,
OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS,
LOSS OF INFORMATION OR OTHER FINANCIAL LOSS
ARISING OUT OF OR IN CONNECTION WITH THE ABILITY
OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES
TO THE FULL EXTENT THESE DAMAGES MAY BE
DISCLAIMED BY LAW.
Some jurisdictions do not allow the limitation or exclusion of
incidental or consequential damages, or limitation on the length
of an implied warranty, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights that vary from one
jurisdiction to another.
Products Covered
Consumer Products
Length of Coverage
One (1) year from the date of the
products original purchase by the
first consumer purchaser of the
product.
Consumer Accessories
Ninety (90) days from the date of
(battery, power supply(s) the accessories original purchase
and line cords)
by the first consumer purchaser of
the product.
Consumer Products and The balance of the original
Accessories that are
warranty or for ninety (90) days
Repaired or Replaced
from the date returned to the
consumer, whichever is longer.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
Batteries. Only batteries whose fully charged capacity falls
below 80% of their rated capacity and batteries that leak are
covered by this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or
neglect, such as physical damage (cracks, scratches, etc.) to
the surface of the product resulting from misuse; (b) contact
with liquid, water, rain, extreme humidity or heavy perspiration,
sand, dirt or the like, extreme heat, or food; (c) use of the
Products or Accessories for commercial purposes or subjecting
the Product or Accessory to abnormal usage or conditions; or
(d) other acts which are not the fault of Motorola or SUNCORP
TECHNOLOGIES LTD., are excluded from coverage.
Use of Non-Motorola branded Products and Accessories.
Defects or damage that result from the use of Non-Motorola
branded or certified Products or Accessories or other peripheral
equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, or modification in any way by
someone other than Motorola, SUNCORP TECHNOLOGIES
LTD. or its authorized service centers, are excluded from
coverage.
19
EN
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola branded housings, or parts,
are excluded from coverage.
Communication Services. Defects, damages, or the failure of
Products or Accessories due to any communication service or
signal you may subscribe to or use with the Products or
Accessories is excluded from coverage.
How to Obtain Warranty Service or Other
Information?
To obtain service or information, please call: +852 2185 1305.
Email: INFO@USTEL.COM.HK
You will receive instructions on how to ship the Products or
Accessories at your expense, to SUNCORP TECHNOLOGIES
LTD. It is the responsibility of the purchaser to contact the
nearest authorised service center/distributor and bring the
product at the purchaser's risk to that authorised service center.
Authorized Repair Center
To obtain service, you must include: (a) the Product or
Accessory; (b) the original proof of purchase (receipt) which
includes the date, place and seller of the Product; (c) if a
warranty card was included in your box, a completed warranty
card showing the serial number of the Product; (d) a written
description of the problem; and, most importantly; (e) your
address and telephone number.
Technical Information
15. Wall mounting
How many telephones can I have?
IMPORTANT
All items of telephone equipment have a Ringer Equivalence
Number (REN), which is used to calculate the number of items
which may be connected to any one telephone line. Your
D1100 has a REN of 1. A total REN of 4 is allowed. If the total
REN of 4 is exceeded, the telephones may not ring. With
different telephone types there is no guarantee of ringing, even
when the REN is less than 4.
Any additional handsets and chargers that you register have a
REN of 0.
Before you wall-mount your D1100, check that you are not
drilling into any hidden wiring or pipes.
Before you drill, make sure the power and telephone line cables
will reach the sockets.
1. Use the following templates to mark the drilling locations.
• To wall-mount the base, drill two holes in the wall 4.5cm
apart horizontally using an 8mm drill bit.
R&TTE
This product is intended for use within Vietnam for connection
to the public telephone network and compatible switchboards.
This equipment complies with the essential requirements for
the Radio Equipment and Telecommunications Terminal
Equipment Directive 1999/5/EC. including compliance with
ICNIRP standard for electromagnetic energy exposure.
Connecting to a switchboard
This product is intended for use within Vietnam for connection
to the public telephone network.
Inserting a pause
With some switchboards, after dialling the access code you
may have to wait for a moment while the switchboard picks up
an outside line so you will need to enter a pause in the dialing
sequence.
Press and hold u to insert a pause (P) before entering the
telephone number.
You may also need to enter a pause when storing international
numbers or charge card numbers.
Recall
You may need to use the recall function if you are connected to
a switchboard/PABX (Private Automatic Branch Exchange),
contact your PABX supplier for further information.
20
Wall mounting
• To wall-mount the charger, drill two holes in the wall 3.2cm
apart horizontally using an 8mm drill bit.
2. Insert the wall plugs if necessary, then insert the screws
leaving about 5mm protruding from the wall on which to
hang the phone.
3. Pull the base/charger out of the stand and slot the holes on
the back of the base over the screw heads and gently pull
the base/charger down to make sure it is securely in place.
Wall mounting
21
Declaration of Conformity (DoC)
Suncorp declares that the following products:
Brandname:
Type:
Descriptions:
Motorola
D1101, D1102, D1103, D1104, D1111, D1112, D1113 and D1114
DECT phone with telephone answering machine (D110x) and
without telephone answering machine (D111x),
and their multi-handset versions.
R&TTE Directive (1999/5/EC)
Ecodesign Directive (2005/32/EC)
to which this declaration related is in conformity with the essential requirements of the following
directives of the Council of the European Communities:
-
EN60950-1:2006
EN301489-1 v1.6.1 and EN301489-6 v1.2.1
EN301406 v1.5.1
EC No 278/2009, 6 April 2009
The products are compliant with the following standards:
Safety:
EMC:
RF Spectrum:
Ecodesign:
CW
2010.05.03 19:47:57 +08'00'
3rd May 2010
3001-3005 China Resources Building, 26 Harbour Road,
Wan Chai, Hong Kong
______________________
CW Cheung - Chief Technical Officer
For and on behalf of Suncorp Global Limited,
Signature:
Printed name & Position:
Date:
Place:
Wall mounting
22
EN
Manufactured, distributed or sold by Suncorp
Technologies Ltd. official licensee for this product.
MOTOROLA and the Stylized M Logo, and other
Motorola trademarks and trade dress are owned by
Motorola, Inc. and are used under license from
Motorola, Inc. MOTOROLA and the Stylized M Logo
are registered in the US Patent & Trademark Office.
All other product or service names are the property
of their respective owners.
© Motorola, Inc. 2010. All rights reserved.
Version 1 (VN)
Download PDF