MD-219 Series Hardware Installation Installing the MD-219

Add to my manuals
2 Pages

advertisement

MD-219 Series Hardware Installation Installing the MD-219 | Manualzz

MD-219 Series

Quick Installation Guide

First Edition, September 2014

Overview

The MD-219 is the 19-inch version of our marine display series.

Designed for durably reliable service as an ECDIS display component, the MD-219 has a 5:4 aspect ratio, alongside full range dimming and optional optical bonding, making it well-suited not only for ECDIS applications, but for a variety of other bridge applications as well.

The MD-219 features both AC and DC power inputs, and may be conveniently installed on any bridge, without the need for extra hardware.

Moxa’s marine displays are compliant with the most important industrial marine standards, including IEC 60945, DNV, and

IACS-E10, giving strong assurance of their suitability for marine applications.

Package Checklist

Before installing the MD-219 Series, verify that the package contains the following items:

• MD-219 display

• VGA cable

• DVI-D cable

• 2-pin terminal block x 1

• 5-pin terminal block x 2

• Documentation and software CD

• Quick installation guide (printed)

• Warranty card

NOTE: Please notify your sales representative if any of the above items are missing or damaged.

– 1 –

P/N: 1802002190010

Hardware Installation

Appearance

SavvyTouch Display Control Buttons

The following table describes the SavvyTouch display controls on the front surface of the MD-219. These intelligent controls light up in response to a simple wave of the hand over the area of the screen where they are located.

Name

Menu/

Power

Display

Color

Control Function / Color Legend

Green

Red

Off

Display is powered on and functioning normally. Touch the button to show the OSD settings menu

No input signal detected. Display standby

Power is down and the display is off

+: To increase brightness of panel

Brightness White

-: To decrease brightness of panel

Info

Off

Red

AC/DC power functioning normally

Display White

AC/DC power error

Switch between DAY/DUSK/NIGHT brightness modes

Panel brightness out of default range

– 2 –

Installing the MD-219

Desktop

The MD-219 comes with optional brackets that allow you to install the display on a horizontal surface, such as a desktop. Three round screws are required for each bracket. See the figure at the top of the next page for detailed screw specifications, including the required torque values.

Place your MD-219 display on a clean, flat, well-ventilated desktop.

To protect the display from overheating, leave some ventilation space between the MD-219 and other equipment. Do not place equipment or objects on the panel, as this might damage internal components.

– 3 –

Panel Mounting

The MD-219 comes with 14 optional clamp mounts for installation on a wall (where space has been cut out to accommodate the rest of the hardware) or into computing stations where a flush mount is desired. The maximum thickness of the surface to which the

display will be clamped is 11 mm. For a secure mounting, all 14 clamps must be used. The clamp arms are fastened into slots on all four sides of the MD-219. Use the short M4 SUS screws to fasten the clamp arms to the MD-219 mounting slots, as shown in the magnified inset in the diagram just below. Next, use the clamps to fasten the display to its mounting point; note the torque value shown in the figure inset below.

VESA Mounting

The MD-219 also comes with an optional VESA mounting kit. Six flat screws and four round screws are required to fasten the VESA mounting bracket. See the figure below for detailed screw specifications and torque values.

Connector Description

Extending the Display

The MD-219 comes with both standard VGA and DVI-D interfaces on the bottom panel. It will automatically detect whether the input video source is from the VGA or DVI-D interface.

Configuring the Display via the Serial Port

The MD-219 has two serial ports. The RS-232 port uses a DB9 connector, and the RS-422/485 port uses a terminal block connector. Either serial port can be used to modify the display parameters using UART commands. Refer to the MD-219 User’s

Manual for serial port configuration details. The pin assignments for the ports are shown in the following table:

Pin RS-232

1 DCD

2 RxD

3 TxD

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

Pin RS-422 RS-485 (2-wire)

1 RxDB(+) TDp(+)

2 RxDA(-) TDn(-)

3 TxDB(+) RDp(+)

4 TxDA(-) RDn(-)

5 GND GND

Powering on/off the MD-219

To power on the MD-219, connect to an AC power source, a DC power source, or both. Touch the MENU button for 1 second to turn on the display. Touch the MENU button for 4 seconds to turn off the display.

An additional four screws (not included in the kit) are required to mount the display on a VESA rack. For this purpose, use M6 screws with a length between 10 and 12 mm.

– 4 –

NOTE If only one power input is being connected, the INFO button will be red. This will not affect the functionality and performance of MD-219 as long as the power input is stable.

– 5 –

Grounding the MD-219 Series

Proper grounding and wire routing help to limit the effects of noise from electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting the power source.

For detailed configuration of the MD-219, refer to the MD-219

Series User’s Manual. www.moxa.com/support

The Americas: +1-714-528-6777 (toll-free: 1-888-669-2872)

Europe: +49-89-3 70 03 99-0

Asia-Pacific: +886-2-8919-1230

China: +86-21-5258-9955 (toll-free: 800-820-5036)

 2014 Moxa Inc.All rights reserved.

– 6 –

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement