WINEGARD

®

RoadTrip

®

Mission

™

Automatic Satellite TV Antenna

Made in the U.S.A.

PRODUCT REGISTRATION

Please register your Winegard product by filling out and returning the Product Registration card provided or by completing the online registration form at http://www.winegard.com/registration

Serial No.

Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000

800/788-4417 • FAX 319/758-5854 • www.winegard.com

Printed in U.S.A. © Winegard Company 2011 2452219

1

Parts Included • Tools Needed • Unpacking the Unit

PARTS INCLUDED:

1 RoadTrip Mission Automatic Satellite TV Antenna

1 Hardware bag containing:

2 Cable Ties

Wall Plate

On/Off Power Switch

2 Insulated Terminals

Flag Terminal

2 Cable Clamps

Cable Entry Plate

16 Mounting Screws

1 30’ RG6 Coax

1 25’ Power Cable

TOOLS NEEDED FOR UNPACKING & INSTALLATION:

Level

Drill with 3/4” bit

1-1/4” hole saw (if mounting switch in wall)

Phillips screw driver #2

7/16” Open end wrench

Mounting Hardware & Sealant (consult vehicle manufacturer)

UNPACKING THE UNIT:

1 . Open box and remove packing material.

2. Lift unit out of box vertically. Do not turn box and “roll” out, or turn upside down to remove.

!

If using knife to open carton, BE CAREFUL.

Do not cut the dome on the unit.

USE 2 PEOPLE when removing the unit from the carton.

For Winegard Warranty Information:

Attn: Technical Services

Winegard Company

3111 Kirkwood St.

Burlington, IA 52601

Ph: 800-788-4417

Fax: 319-758-5854

!

DO NOT PAINT DOME!

Painting dome will cause signal degradation and will void your warranty.

Disclaimer:

Although every effort has been made to insure the information in this manual is correct and complete, no company shall be held liable for any errors or omissions in this manual. Changes and technological advances are continuously being made in the satellite market. Information provided in this manual was accurate at the time of printing. If the RoadTrip® Mission™ does not function as expected, please contact Winegard Company at (800)

788-4417 or visit our website at www.winegard.com.

Trademarks:

Winegard and RoadTrip are registered trademarks of Winegard Company. Mission is a trademark of Winegard

Company. DISH Network is a registered trademark of EchoStar Satellite L.L.C. DIRECTV is a registered trademark of DIRECTV, Inc., a unit of Hughes Electronics Corp. Bell TV is a trademark of Bell Canada, Inc. All trademarks contained in this manual are property of their respective owners. Reference made to products or services provided by companies, other than Winegard Company, does not represent any endorsement of those products or services.

2

This model is PRESET for DIRECTV

®

receivers.

If you have a

DISH Network

®

or

BELL TV™

receiver, you must change the numbered switches (see figures below).

FACTORY PRESET

DIRECTV SWITCH SETTINGS

TO CHANGE SWITCH SETTINGS FOR DISH

POSITION (#8 SHOULD REMAIN DOWN ALSO).

DIRECTV DISH NETWORK

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

KEY

0 = UP

BELL TV

1 2 3 4 5 6 7 8

1 = DOWN

DISH NETWORK HYBRID

1 2 3 4 5 6 7 8

Hybrid Mode settings are for use in areas where the standard DISH Network settings fail to provide HD programming.

Installing unit on roof of vehicle —

IMPORTANT! Do not install this system in the rain, or under any wet conditions. Moisture may affect electronics and void your warranty!

1. For best performance and to reduce signal acquisition time, park vehicle on a level surface; level the RV.

2. Select a level spot on your roof for installation.

WARNING: Level the base front to back and side to side. If base is not level the antenna may require more time to locate the correct satellite or may not locate the correct satellite.

3. Ensure proper distance to other rooftop equipment is maintained.

Be sure no roof-mounted equipment is blocking the satellite “line of sight”; see chart below.

Using this chart, determine the minimum distances to other equipment.

FIGURE 1

Programming Availability —

DISH Network Standard and HD —

110°, 119°, 129°

DISH Network Hybrid —

61.5°, 110°, 119°

DIRECTV Standard —

101°, 119° (will not receive HD on 110° or any KA-band HD on 99° and 103°)

BELL Standard and HD —

82° and 91°

OBSTRUCTION

2 3 4 5

UNIT BASE

15”

12”

10”

8”

43.5”

17.5”

25.0”

32.5”

3

4. After selecting location for unit (see Step 2), place the unit on the centerline of the vehicle.

5. Position base so that cables exit toward the rear of vehicle.

FIGURE 2

Center Line of Vehicle

Cable entry installation —

1. Connect the quick disconnect power cable to the panel mount on the back of the RoadTrip Mission unit.

See Figures 4 & 5 below.

Cable connections

MUST face REAR

FIGURE 4 QUICK DISCONNECT SOCKET

LOCK (ON TOP OF THE CONNECTOR)

MAIN Port SECONDARY Port

At least 12” At least 12”

FRONT OF VEHICLE

The distance from the edge of the roof to the near corner of any foot should be at least 12” on both sides of the dish to ensure proper installation.

6. Place the unit on the roof in its permanent location and mark around each base foot, Figure 3. Set the unit aside for later.

FIGURE 3

FIGURE 5

LOCK

POWER PLUG

CENTER

POINT

OF FOOT

SHOULD

POINT

AWAY

FROM THE

DOME.

Decide the best location for the power and coax cables to enter the vehicle, and the location of the power switch and receiver. Drill a 3/4” hole in the roof, push wires inside.

2. Connect the primary receiver to the “MAIN” Port on the base, Figure 4.

3. For a two receiver installation, connect a second coax cable (not provided) to the secondary port on base marked “SEC” and run cable along roof to second receiver location.

4. Place cable-entry plate over hole and cables. Screw in place. Seal plate and screw holes with approved sealant (not included).

5. Depending on the length of the cable on the roof, you may need to use cable clamps or wire ties (not provided) between the unit and your cable-entry plate.

Clamping the cable every 12”-16” should eliminate any unnecessary cable movement, Figure 6.

7. Clean roof area where the base feet will be attached to the roof. Do not erase your marks!

8. Put approved sealant in the areas marked for the base feet. Place base feet on top of the sealant and screw down with the (3) #10 screws for each foot.

9. After all base feet are secured to roof, put sealant around edge of feet and over screws.

!

DO NOT apply sealant to the hex nuts on the

RoadTrip Mission feet.

!

NICKS OR CUTS IN WIRING JACKET MAY

CAUSE WATER TO LEAK INTO VEHICLE.

FIGURE 6

CABLE-

ENTRy

12”-16”

CABLE CLAMPS

4

Installing the RoadTrip Mission Dome -

(Not required for a DIRECTV installation - dome installed at factory).

Place the RoadTrip Mission dome over the unit so that the RoadTrip Mission decals on the dome face away from the center line of the vehicle. Line up the holes in the dome with the inserts in the RoadTrip Mission base. Insert all of the dome screws and tighten using a Phillips screwdriver.

!

DO NOT OVERTIGHTEN DOME SCREWS.

Installing the power switch

1. Choose a location to install the RoadTrip Mission power ON/OFF switch. Remember when selecting a location, you will need to run the +12 VDC power cable from the RoadTrip Mission antenna to the switch. Be sure the switch is in the OFF position before continuing. See Figure 7 below.

Drill 1-1/4” hole, pull wires through wall or panel.

2. Connect the ground wire from the vehicle and the

BLACK ground wire from the antenna together, using large yellow flag connector.

3. Connect the YELLOW flag connector to the switch.

4. Connect the RED wire from the antenna to the small RED flag connector.

5. Connect small RED flag connector to the switch.

6. Connect the +12 V power wire from the vehicle to a small RED flag connector.

7. Connect small RED flag connector to isolated

spade on switch.

FIGURE 7

ON/OFF ROCKER SWITCH

WITH LIGHT

(Shown in OFF position.)

STEPS 2 & 3

TWO GROUND WIRES

1 FROM VEHICLE

1 BLACK WIRE FROM

SATELLITE ANTENNA

STEPS 6 &7

+12 V FROM VEHICLE

STEPS 4 & 5

RED POWER WIRE

FROM ANTENNA

CONNECTING RECEIVERS

Connecting ONE receiver

1. Connect the coax cable coming from the “MAIN” port on the antenna to the “SATELLITE IN” on the receiver.

2. See page 6 for receiver set-up.

Connecting TWO receivers

1. Connect the coax cable coming from the “MAIN” port on the antenna to the “SATELLITE IN” input on the primary receiver. The primary receiver should be connected to the TV that will be watched most often.

2. Connect the secondary coax cable coming from the

“SEC” port on the antenna to the “SATELLITE IN” input on the secondary receiver.

NOTE: The primary receiver will always control which satellite the RoadTrip Mission finds. The secondary receiver will be able to view any channel on the satellite chosen by the primary receiver.

3. See page 6 for receiver set-up.

Operating the RoadTrip Mission

1. Turn on receiver and television set. The RoadTrip

Mission antenna must be connected to a receiver that is plugged into 120 VAC.

2. Verify that you are getting the receiver’s menu screens on the television. These screens are available with or without the dish finding the signal.

3. Turn the power switch on for the RoadTrip Mission antenna.

The dish will detect if it is already on a satellite signal. If it detects a signal, the dish will move to check it’s alternate satellite and then move back to the original satellite signal it was on.

NOTE: For Tracking or In-Motion units, the dish should start moving, making one or two revolutions before it stops to acquire GPS. This can take a few moments or up to 10-15 minutes. Normal operation will be less than a minute.

4. If no signal was detected, the dish will begin its search to locate the primary satellite. Once the dish locates a signal, it will pause long enough to identify which satellite it has located. This may or may not be visible on your receiver’s point dish screen.

5. After the unit has verified that it has the correct satellite, it will move to check the alternate satellite and move back to the primary satellite to complete the search routine.

6. If you do not have signal, see Troubleshooting, p.8.

NOTE: Because the RoadTrip Mission antenna uses information from the last location that it was on a signal, satellite acquisition may take longer if the dish is inactive over long distance traveling.

5

Use your on-screen guide to locate your channel rather than “channel surfing”. This will result in smoother operation.

NOTE: If the vehicle does not move for six minutes, the unit will toggle to it’s alternate satellite then toggle back to the primary satellite and go to sleep. If vehicle begins movement in straight line at 10 mph, the unit will resume tracking mode.

Basic RoadTrip Mission Antenna Wiring

TV

COAX

POWER

RECEIVER

SAT IN

COAX

120V

POWER

RoadTrip Mission

ANTENNA

12VDC

To toggle between satellites when subscribing to multi-satellite programming—

The RoadTrip Mission antenna will toggle between the primary or alternate satellites for either DISH

Network or DIRECTV on the primary receiver. Both satellite programming providers have programming on more than one satellite. When a channel is selected on the remote control that is located on a different satellite, the unit will automatically toggle to the correct satellite.

!

To order receivers or programming, please call the Winegard receiver hotline: 1 (866) 609-9374.

DIRECTV programming

DIRECTV receivers must be set for 3-LNB

(18 x 20) sat selection to enable toggling between primary 101° satellite and alternate 119° satellite only. RoadTrip Mission will not receive HD programming on 110° or any KA-band HD on 99° and 103°. (Consult receiver manual for procedure.)

After receiver is set for the correct dish selection, when you request a channel located on a different satellite, the unit will automatically toggle to that satellite.

To install the “SW64” switch:

1. Before turning on your RoadTrip Mission antenna, make sure that your satellite receiver and television are turned on and your receiver is on the “point dish” menu. (Consult your owner’s manual to reach this menu.)

2. Turn on the RoadTrip Mission system and wait for the unit to acquire a signal on satellite 119° and stop moving.

3. you now have six minutes to complete Check

Switch test. Consult your receiver manual for instructions on running the test. Be sure that Superdish and Alternate are unchecked if applicable. On screen options may vary by receiver.

4. During the Check Switch Test, the receiver will begin checking the switch by toggling between satellites. When this is completed, SW64 will appear on the screen. It will be at the near the bottom of the screen. Satellite designations will be below, showing odd and even transponders. See illustration below.

Installation Summary

Check Switch screen display

Port:

Satellite:

Trans:

Device:

Status:

Switch:

Satellite Input

1 2 3

119 110 129

OK OK OK

Reception Verified

SW64

DISH Network programming (DISH 1000)

DISH Network receivers must have the “SW64” switch installed in order to toggle between the primary 119° satellite and the alternates 110° and

129°. (Consult your receiver manual for the procedure to reach the “check switch” menu.)

NOTE: This “SW64 Switch” is a DISH Network receiver setting, NOT a physical part.

6

SuperDISH

Test Done

Alternate

Help

NOTE: Be sure the “Superdish” and

“Alternate” boxes are NOT checked.

If a switch other than SW64 appears, or you have an ‘X’ in one of the boxes below the satellites, repeat Check Switch Steps.

5. your system is now set up to toggle between satellites. It will automatically move to the correct satellite when a channel is selected with your remote control.

NOTE: Once these steps are completed, you won’t have to perform this test again, unless

Check Switch was performed on another satellite dish, such as a home dish.

Toggle: The RoadTrip Mission is an automatic single satellite antenna capable of viewing only one satellite at a time. To provide all of the programming for multiple satellite packages, the RoadTrip Mission will move between each of the satellites as required by the Primary receiver. This means that the Primary receiver will function very much like a home satellite antenna in that it will seamlessly move from primary to alternate satellites as required by the receiver. However, the secondary receiver will only provide programming from the satellite that the Primary receiver is on or was last using.

Note: The RoadTrip Mission antenna is designed to be maintenance free. However, it is a good idea to clean the dome from time to time with a soft cloth, water and dish soap.

Warning: Painting the RoadTrip Mission dome voids the warranty, degrades signal strength and may cause damage to the antenna.

To order receivers or programming call (866) 609-9374.

DIRECTV must be set to the “two” satellite, oval dish setting. Refer to your receiver manual.

DISH Network receivers must have the check switch set to “SW64”. See page 6.

7

Troubleshooting

PROBLEM

The RoadTrip Mission antenna does not attempt to find a satellite or it never moves.

SOLUTION

1. Check +12 V wires at unit to verify the quick disconnect is locked into the socket.

The dish never stops on any of the signals that it sees.

1. Make sure that your receiver is set up correctly.

For DISH NETWORK, the check switch should read either

“ Unknown” or “SW64”.

For DIRECTV, the receiver should be set for a Two Satellite

Oval Dish. In some cases, the ‘Two satellite’ option may not be available. In these cases, select Three satellite oval.

2. Make sure the Main coax cable from antenna is run to

“satellite in” on back of your receiver and all coax connections are made properly.

With DIRECTV, the dish will find the alternate satellite but it never finds the primary satellite.

Make sure that the Switches on the Electronics Control Box are set for DIRECTV. See page 3. These switches are found under the dome, inside the Electronics Control Box.

I am not getting all the DISH Network channels

I subscribed to.

Go to the check switch menu in receiver. Make sure that it’s set for

SW64 and lists both even and odd transponders on satellites 110°,

119° and 129°.

The RoadTrip Mission antenna never sees any signals, it just keeps searching.

1. Rain, snow or excessive dew on the dome can interrupt the signal. Snow and dew can be brushed off the dome. If heavy rain or snowfall is blocking the signal, it may be necessary to wait until the weather clears.

2. Check to see if the southern sky is clear. Trees, buildings, large signs or an overpass can block the signal. Find an area where you can be sure that this is not the problem and try again.

3. Run a single, good coax cable directly from the RoadTrip

Mission to the satellite receiver by-passing everything.

4. Make sure the receiver has power and the satellite dish is connected to the “Sat In” jack.

I have switched satellite service providers. How do I set my dish for my new provider?

you will need to remove the dome, and set switches to correct provider. See page 3.

My receiver appears to be locked up. I cannot get any response from it.

1. Power off receiver and turn back on.

2. Hold in power button on receiver for three seconds and release.

3. Unplug receiver from outlet for 20 seconds and plug back in.

With DISH Network, my RoadTrip Mission antenna appears to lock onto signal, but my receiver does not show a picture or a signal reading.

The DIRECTV receiver shows a signal but the RoadTrip Mission antenna never stops searching.

Check the “Check Switch” installed in your receiver. If anything other than “Unknown” or “SW64” is installed, please run the

“Check Switch” test. See page 6 for help running this check.

Exit the receiver menu screens and try running the search from the program guide screen.

8

Appendix A Satellite Coverage Maps and Receiver Compatibility

A.1 DISH Network Programming

The RoadTrip Mission antenna will operate with most DISH Network receivers.

Winegard does not recommend using receivers with hard drives not recommended by the manufacturer for mobile applications. Winegard recommends using a standard DISH Network receiver.

The antenna will locate and toggle between satellites 110°, 119° and 129°.

The RoadTrip Mission antenna will not operate in areas where satellite 110°, 119° and 129° are not available.

Refer to figure below for an operational coverage map for satellite 110° and 119°. Satellite coverage maps are based on level, stationary operation.

Reception interruption may also occur during adverse weather conditions.

DISH Network satellites 110° and 119° coverage area (Dotted area indicates coverage).*

*Coverage maps are for reference only and do not guarantee coverage.

Note: There are certain areas within the U.S. where the RoadTrip Mission antenna may experience limited or no coverage of the 129 o satellite for HD programming. DISH Network home coverage has the same limitations.

Problem areas include: Washington, Oregon and California (limited coverage may extend past these areas).

Contact DISH Network for any additional coverage questions (888.825.2557).

9

Hybrid Mode is for use with DISH Network in the Northeast where the 129° satellite is not available.

The map below shows the coverage area for DISH Network satellite 129°. (Dotted area indicates coverage).

*

*Coverage maps are for reference only and do not guarantee coverage.

DISH Network satellite 61.5° coverage area (Dotted area indicates coverage).*

*Coverage maps are for reference only and do not guarantee coverage.

DISH Network

If neither DISH Network Standard Mode or DISH Network Hybrid Mode will provide an HD signal, consult the maps above. If you are in the 61.5° coverage area, use DISH Network Eastern Arc.

®

EASTERN ARC

1 2 3 4 5 6 7 8

DISH NETWORK 72° SATELLITE USES THE

ODD TRANSPONDERS ONLY. A CHECK

SWITCH WILL FAIL TO SEE ANY EVEN

TRANSPONDERS. THIS IS NORMAL.

10

A.2 DIRECTV Programming

The RoadTrip Mission antenna will operate with most DIRECTV receivers. The antenna will locate and continually track satellites 101° and 119°. However, the RoadTrip Mission is not compatible with the

DIRECTV 110° satellite or the KA band satellites 99° and 103°.

Winegard does not recommend using receivers with hard drives not recommended by the manufacturer for mobile applications. Winegard recommends using a standard DIRECTV receiver.

RoadTrip Mission antenna will operate in all areas where satellites 101° and 119° are available. Refer to the figures below for an operational coverage map of satellite 101° and 119°. Satellite coverage maps are based on level, stationary operation.

Reception interruption may also occur during adverse weather conditions.

DIRECTV satellite 101° RoadTrip Mission coverage map (Dotted area indicates coverage).*

DIRECTV satellite 119° RoadTrip Mission coverage map (Dotted area indicates coverage).*

*Coverage maps are for reference only and do not guarantee coverage.

11

RoadTrip Mission Specifications & Warranty

Features and specifications

• One button operation

• Supports up to 2 single or 1 dual receiver

• Depending on receiver type and location, you can

access satellites

DISH Network 61.5°, 110°, 119° or 129°

DIRECTV 101° or 119°

BELL TV 82° or 91°

• Depending on programming, can access DISH

Network’s East Coast local feeds

• Elevation range 15° to 65°;

azimuth +360° (0-698°)

• UV protected plastic dome

• Compact size —

20” diameter, 12.9” height

Shipping size - 15 3/4” x 22 1/2” x 22 1/2”

Unit weight - 14 lbs.

Shipping weight - 22 lbs.

• Operating temperature -13°F to +140°F

• Specifications for max amperage 5.0A

• Specifications for unit operating voltage -10.5 -

13.8V

• Specifications for supply voltage 12 - 13.8V

WINEGARD MOBILE PRODUCTS LIMITED WARRANTY

(2 YEARS PARTS; 1 YEAR LABOR)

Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products. No warranty claim will be honored unless at the time the claim is made, Customer presents proof of purchase to an authorized Winegard dealer (to locate the nearest authorized

Winegard dealer, contact Winegard Company, 3000 Kirkwood Street, Burlington, Iowa 52601, Telephone 800-288-8094 or visit www.winegard.com). Customer must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product is under warranty. If the date of purchase cannot be verified, the warranty period shall be considered to begin thirty (30) days after the date of manufacture.

If a defect in material or workmanship is discovered, Customer may take the product to an authorized Winegard dealer for service. Customer must provide proof of purchase to verify the product is under warranty. If the product is brought to an authorized Winegard dealer for service prior to expiration of year one (1) of the warranty period and a defect in material or workmanship is verified by Winegard Technical Services, Winegard Company will cover the Winegard dealer’s labor charges for warranty service. The Winegard dealer must contact Winegard Technical Services in advance for pre-approval of the service. Approval of the service is at the sole discretion of Winegard Company.

Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at 3111 Kirkwood Street, Burlington, Iowa 52601, Telephone 800-788-

4417). Customer must return the product along with a brief description of the problem and provide Winegard Technical Services with Customer’s name, address, and phone number. Customer must also provide proof of purchase to verify the product is under warranty. If the product is returned before the expiration of the warranty period, Winegard Company will (at its option) either repair or replace the product.

This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions or fails from: improper installation, misuse, abuse, neglect, accident, tampering, modification of the product as originally manufactured by Winegard in any manner whatsoever, removing or defacing any serial number, usage not in accordance with product instructions or acts of nature such as damage caused by wind, lightning, ice or corrosive environments such as salt spray and acid rain. This Limited Warranty also does not apply if the product becomes unable to perform its’ intended function in any way as a result of the television signal provider making any changes in technology or service .

RETURN AUTHORIZATION POLICY

A Return Material Authorization (RMA) is required prior to returning any product to Winegard Company or Winegard Warranty Services under this warranty policy. Please call our Technical Services Department at 800-788-4417 or send an e-mail to [email protected] to obtain the RMA number. Please furnish the date of purchase when requesting an RMA number. Enclose the product in a prepaid package and write the RMA number in large, clear letters on the outside of the package. To avoid confusion or misunderstanding, a shipment(s) without an RMA number(s) or an unauthorized return(s) will be refused and returned to Customer freight collect.

WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE BY ANY OTHER

PERSON.

ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND

MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY.

In states that do not allow limitations on implied warranties, or the exclusion of limitation of incidental or consequential damages, the above limitations or exclusions do not apply.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

This warranty gives Customer specific legal rights. Customer may also have other rights that may vary from state to state

SATELLITE RECEIVER WARRANTY

See manufacturer’s limited warranty policy.

WS-MOBWARREV2

Rev. 1/10

Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601 • 800/788-4417 Fax 319/758-5854 • www.winegard.com

Printed in U.S.A. © 2011 Winegard Company 2452219

12