Venstar T2300FS Owner`s manual

Venstar T2300FS Owner`s manual
residential
Digital
Thermostat
THERMOSTAT
T2300FS
7-Day
PROGRAMMABLE
up to 2-heat
& 2-cool
HEAT
COOL
Control up to 2 Heat & 2 Cool Stages
7-Day Programmable
4 Settings/Day
Auto Changeover
5 minute Built-In
Compressor Protection
Self-Prompting Programming
with Copy Command
Display Either F or C
HEAT
PUMP
Mounts Flush with the Wall
Back-Lit display
One For All Works with
Virtually All Equipment
Non-Volatile memory
Holiday/Vacation Programming
Keypad lockout
Dual setpoint with
Adjustable Deadband
‘O’ or ‘B’ Terminal
Optional: Remote Sensor
Ready
Dry Contact Equipped
Use with most Air Conditioning & Heating Systems including: 1 or 2 Stage
Electric Cooling & 2 Stage Gas Heating, Heat Pump, Electric or Hydronic Heat.
INSTALLATION
INSTRUCTIONS
Venstar Inc. 08/07
Table Of Contents
Step #1: Preparation
2
Step #2: Remove & Replace
Old Thermostat
3
Step #3: Wire Connections
4
Step #4: Test Operation
12
Trouble Shooting
13
CAUTION
Follow Installation Instructions carefully.
DISCONNECT POWER TO THE HEATER AIR CONDITIONER BEFORE REMOVING
THE OLD THERMOSTAT AND INSTALLING
THE NEW THERMOSTAT.
WARNING
Venstar Inc. 08/07
P/N T2300FS
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Page 1
STEP #1
PREPARATION
FLATSTAT
EXTENDS
LESS THAN
3/8” FROM
THE WALL.
Flat Blade
Screwdriver
Wire cutter
& Stripper
.366”
Make sure your Heater/Air Conditioner
is working properly before beginning
installation of the thermostat.
Carefully unpack the thermostat.
Save the screws, wall anchors, and
instructions.
Turn off the power to the Heating/Air
Conditioning system at the main fuse
panel. Most residential systems have
a separate breaker for disconnecting
power to the furnace.
Page 2
FlatStat
in Small
J-Box
WALL
Assemble tools & recommended
Junction Box.
WALL
Proper installation of the thermostat will be
accomplished by following these step
by step instructions. If you are unsure
about any of these steps, call a qualified
technician for assistance.
STEP #2
REMOVE & REPLACE OLD THERMOSTAT
Remove the cover of the old thermostat.
If it does not come off easily check for
screws.
Loosen the screws holding the thermostat
base or subbase to the wall, and lift away.
Disconnect the wires from the old
thermostat. Tape the ends of the wires
as you disconnect them, and mark them
with the letter of the terminal for easy
reconnection to the new thermostat.
Keep the old thermostat for reference
purposes, until your new thermostat is
functioning properly.
Remove the white plastic wire connector
from the rear of the thermostat. Install
wires as directed. Press the wired
connector on the back of the thermostat.
Lift Connector straight up
to remove.
For best operation, install
the thermostat in a junction
box that is free from drafts
that originate inside the wall.
Page 3
STEP #3
WIRE CONNECTIONS
If the terminal designations on your old
thermostat do not match those on the
new thermostat, refer to the chart below,
or the wiring diagrams that follow.
Wire from the
old thermostat
terminal marked
Function
G or F
Fan
Y1, Y or C
Cooling
W1, W or H
Heating
Install on the
new thermos tat
connector marked
G
Y1
W1,O,B
Rh, R, M, Vr, A
Power
C
Common
C*
R
O/b
Rev. Valve
W1,O,B**
Y2
2nd Stage Cool
Y2
W2
2nd Stage Heat
W2
RS+5
Remote Sensor +5vdc
RS+5
RS
Remote Sensor Signal
RS
RS G
Remote Sensor Ground
GND
CK1
Dry Contact Switch 1
CK1
CK2
Dry Contact Switch 2
GND
* C may not be used on all systems.
** O/B is used if your system is a Heat Pump.
Page 4
Sample Wiring Diagrams
Gas or Electric Heat
5 Wire, 1 Stage Cooling, 1 Stage Gas Heat
W
FAN
G
COMPRESSOR
COMMON
C
GAS VALVE
or
STRIP HEAT
Y
POWER
CK1
GND
RS
RS+5
W2
Y2
R
C
G
Y1
W1-O-B
R
Residential Gas or Electric Heat*,
Electric Cool, split systems & package
units
* If using first stage electric heat, this option must be
selected ON (see page 16, step 6 of Owner’s Manual).
Page 5
Sample Wiring Diagrams
Gas or Electric Heat
4 Wire, 1 Stage Cooling, 1 Stage Gas Heat
GAS VALVE
or
STRIP HEAT
W
COMPRESSOR
Y
FAN
G
POWER
CK1
GND
RS
RS+5
W2
Y2
R
C
G
Y1
W1-O-B
R
Residential Gas or Electric Heat*,
Electric Cool, split systems & package
units
* If using first stage electric heat, this option must be
selected ON (see page 16, step 6 of Owner’s Manual).
Page 6
Sample Wiring Diagrams
Gas or Electric Heat
6 Wire, 2 Stage Cooling, 1 Stage Gas Heat
W
COMPRESSOR
COMMON
C
2nd STAGE
COOLING
Y2
FAN
G
GAS VALVE
or
STRIP HEAT
Y
POWER
CK1
GND
RS
RS+5
W2
Y2
R
C
G
Y1
W1-O-B
R
Residential two stage cooling with
Gas or Electric Heat*.
* If using first stage electric heat, this option must be
selected ON (see page 16, step 6 of Owner’s Manual).
Page 7
Sample Wiring Diagrams
Gas or Electric Heat
6 Wire, 1 Stage Cooling, 2 Stage Heat
Residential & commercial 1 Stage Cooling,
with 2 Stage Gas or Electric Heat*
W
COMPRESSOR
COMMON
C
2nd STAGE
HEATING
W2
FAN
G
GAS VALVE
or
STRIP HEAT
Y
POWER
CK1
GND
RS
RS+5
W2
Y2
R
C
G
Y1
W1-O-B
R
* If using first stage electric heat, this option must be
selected ON (see page 16, step 6 of Owner’s Manual).
Page 8
Sample Wiring Diagrams
Gas or Electric Heat
Commercial Gas or Electric Heat *,
Electric Cool, split systems & package units
including Commercial Heat Pumps **
7 Wire, 2 Stage Cooling, 2 Stage Heat
W
COMPRESSOR
COMMON
C
2nd STAGE
HEATING
2nd STAGE
COOLING
Y2 W2
FAN
G
GAS VALVE
or
STRIP HEAT
Y
POWER
CK1
GND
RS
RS+5
W2
Y2
R
C
G
Y1
W1-O-B
R
* If using first stage electric heat, this option must be
selected ON (see page 16, step 6 of Owner’s Manual).
** Commercial heat pumps do not have the heat pump turned
ON in advanced setup (see page 15, step 4 of Owner’s Manual).
Page 9
Sample Wiring Diagrams
Heat Pump
5 Wire, 1 Stage Cooling, 1 Stage Heat-Heat Pump* with O or b reversing valve**.
Residential Heat Pumps, split systems & package units, with no auxiliary heat.
R
O/b
COMPRESSOR
FAN
G
REVERSING VALVE**
COMMON
C
POWER
Y
C
G
Y1
W1-O-B
R
CK1
GND
RS
RS+5
W2
Y2
* This option must be selected ON during advanced setup
(see page 15, step 4 of Owner’s Manual).
** This option must be selected O or b during advanced setup
(see page 16, step 5 of Owner’s Manual).
Page 10
Sample Wiring Diagrams
Heat Pump
6 Wire, 1 Stage Cooling, 2 Stage Heat-Heat Pump* with O or b reversing valve**.
Residential Heat Pumps, split systems & package units, with auxiliary heat.
O/b
COMPRESSOR
COMMON
C
2nd STAGE
HEATING
W2
FAN
G
REVERSING VALVE**
Y
POWER
CK1
GND
RS
RS+5
W2
Y2
R
C
G
Y1
W1-O-B
R
* This option must be selected ON during advanced setup
(see page 15, step 4 of Owner’s Manual).
** This option must be selected O or b during advanced setup
(see page 16, step 5 of Owner’s Manual).
Page 11
STEP #4
TEST OPERATION
Turn the power on to the Heating/Air
Conditioning system.
Press the MODE button repeatedly until
the HEAT icon appears on the display.
Press the UP or DOWN buttons until the set
temperature is 10 degrees above room
temperature.
The HVAC unit should
energize in the heating mode.
Press the MODE button repeatedly until
the COOL icon appears on the display.
Press the UP or DOWN buttons until the set
temperature is 10 degrees below room
temperature.
The HVAC unit should
energize in the cooling mode.
NOTE: Most equipment has a time delay
of 5 minutes between cool cycles. This
feature is defeatable on the thermostat
(see page 16, step 9 of Owner's Manual).
Press the UP button until the set temperature is equal to the room temperature;
cooling should deenergize. Follow the
instructions on page 15 of the Owner’s
Manual to turn the fan on in step 3. The
fan should turn on and run continuously.
Page 12
TROUBLESHOOTING
SYMPTOM: When using 4 wires (R, G, W, Y),
the air conditioning equipment tries
repeatedly to turn on, but cannot. At
times the display dims or disappears.
CAUSE: There is not enough power available
to "power share".
REMEDY: Connect a 250 ohm, 10 watt power
resistor at the furnace as shown below.
R
G
W
Y
C
TR300-10w
SYMPTOM: The air conditioning does not
attempt to turn on.
CAUSE: The compressor timer lockout may
prevent the air conditioner from
turning on, for a period of time.
REMEDY: See page 16 of the Owner's Manual
and configure step 9 to defeat the 5minute compressor lockout.
SYMPTOM: The display is blank.
CAUSE: Lack of proper power.
REMEDY: Make sure power is turned on to
the furnace and 24vac between R & W.
If C is used, 24vac between R & C.
Page 13
TROUBLESHOOTING
SYMPTOM: When controlling a residential heat
pump, and asking for cooling, the heat
comes on.
CAUSE: Heat pump is not selected "ON" in the
Advanced Setup.
REMEDY: See page 15 of the Owner's Manual
and configure step 4 to enable heat pump
operation.
SYMPTOM: When calling for cooling, both
the heat and cool come on.
CAUSE: The thermostat is configured to
control a heat pump and the HVAC
system is a "conventional" (non-heat
pump) system.
REMEDY: See page 15 of the Owner's Manual
and set step 4 to OFF to enable gas
electric operation.
FlatStat
T2300FS
c
FC
Tested to Comply
with FCC Standards
FOR HOME OR OFFICE USE
4Z95
P/N 88-641
Rev. 1
Page 14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement