OPERATOR’S

MANUAL

FABRIC 3-BAG

GRASS CATCHER

Models: GC-STT/SCZ-61V

© 2012

Congratulations on owning a Scag mower! This manual contains the operating instructions and safety information for your Scag mower accessory. Reading this manual can provide you with assistance in maintenance and adjustment procedures to keep your mower performing to maximum efficiency. The specific models that this book covers are listed on the inside cover. Before operating your machine, please read all the information enclosed.

Scag Power Equipment

Division of Metalcraft of Mayville, Inc.

PART NO. 03309

PRINTED 1/2012

PRINTED IN USA

WARNING

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN

SERIOUS INJURY OR DEATH.

•

•

•

•

•

•

•

•

•

Read this manual completely as well as other manuals that came with your mower.

DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution.

Under no circumstances should the machine be operated on slopes greater than 15 degrees. ALWAYS FOLLOW OSHA APPROVED OPERATION.

DO NOT mow on wet grass. Wet grass reduces traction and steering control.

Keep all shields in place, especially the grass discharge chute.

Before performing any maintenance or service, stop the machine and remove the spark plug wire and ignition key.

If a mechanism becomes clogged, stop the engine before cleaning.

Keep hands, feet and clothing away from power-driven parts.

Keep others off the mow er (only one person at a time)

REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!

HAzARD CONTROL AND ACCIDENT PREvENTION ARE DEPENDENT UPON THE AWARENESS,

CONCERN, PRUDENCE, AND PROPER TRAINING OF THE PERSONNEL INvOLvED IN THE

OPERATION, TRANSPORT, MAINTENANCE, AND STORAGE OF THE EqUIPMENT.

This manual covers the operating instructions and illustrated parts list for:

GC-STT/SCz-61v with a serial number of G8200001 to G8299999

Always use the entire serial number listed on the serial number tag when referring to this product.

Section 1

1.1 INTRODUCTION

GENERAL INFORMATION

This manual has been prepared to provide the information you need to correctly assemble, operate, and maintain this grass catcher. Read it carefully and keep it for future reference.

THE REPLACEMENT OF ANY PART ON THIS PRODUCT

BY OTHER THAN THE MANUFACTURER'S AUTHORIzED

REPLACEMENT PART MAY ADvERSELY AFFECT THE

PERFORMANCE, DURABILITY OR SAFETY OF THIS

PRODUCT.

A replacement manual is available from your authorized

Scag Service Dealer or by contacting: Scag Power

Equipment, Service Department at P.O. Box 152, Mayville,

WI 53050. You may also contact us through our website at www.scag.com The manual for this grass catcher can be downloaded by using the model and serial number or use the contact form to make your request. Please indicate the complete model and serial number of your Scag product when requesting replacement manuals.

WARNING

USE OF OTHER THAN ORIGINAL SCAG REPLACEMENT

PARTS WILL vOID THE WARRANTY.

Do not operate without discharge chute, mulch kit, operator controlled discharge chute (OCDC), or entire grass catcher installed.

If additional information or service is needed that is not outlined in this manual, please contact your Scag Power

Equipment dealer. Scag dealers are trained in the latest service methods and carry a full line of Scag replacement parts.

When ordering parts, always provide the complete model number and serial number of your catcher.

2. Before removing the grass bags, disengage the mower, stop the engine and wait for all movement to stop.

3. ALWAYS turn the engine OFF, remove the key and wait for all movement to stop before servicing or cleaning the mower or the grass catcher.

All information provided in this manual is based upon information available at the time of printing. Scag Power

Equipment reserves the right to make changes at any time without notice or obligation.

DANGER

ROTATING BLOWER

BLADES

1.2 DIRECTION REFERENCE

STOP ENGINE BEFORE

ENTERING CHUTE

The “Right” and “Left”, “Front” and “Rear” of the machine are referenced from the operator’s right and left when seated in the normal operating position and facing the forward travel direction.

CONTACT CAN INJURE

1.3 SAFETY AND OPERATING

INSTRUCTIONS

4. Do not modify or alter any component of the grass catcher attachment or mower.

5. Do not allow any passengers to ride on the grass catcher attachment or on the mower.

note -

To avoid personal injury, it is imperative that all safety instructions be observed.

1. Read this operator's manual and the operator's manual that is supplied with the machine this attachment is used on.

R

1

R

Section 2

2.1 ASSEMBLY INSTRUCTIONS

- note -

Use the illustrated parts list as a part number reference when following the assembly instructions.

REMOVE DISCHARGE

CHUTE AND

HARDWARE

INSTALL PULLEY

ON RH SPINDLE SHAFT -

ON TOP OF EXISTING

SPINDLE DRIVE

PULLEY

REMOVE EXISTING

RT. SIDE BELT

COVER

-IMPoRtAnt-

When installing this grass catcher on a machine, one of the following Installation Kits must be installed.

STT61V - Installation Kit p/n 9096

STT61V-28CAT - Installation Kit p/n 9079

SCZ61V - Installation Kit p/n 9079

1. Remove all packaging materials. Lay out the mounting hardware and the catcher assembly parts for easy access. Prepare the work area making sure that it is a clean, safe environment

REMOVE (2)

U-NUTS

RIGHT SIDE OF 52"

CUTTER DECK SHOWN

(Note: Some parts not shown for viewing purposes.)

4.

Figure 2-1. Discharge Chute Removal

Install the grass catcher pulley onto the spindle assembly. Apply loctite to both pulley setscrews and tighten. See Figure 2-1.

5. Remove the "Custom-Cut" and "Turbo" baffles from the cutter deck. Using the original hardware, install the new "Front" and "Turbo" baffles. See Figure 2-2.

WARNING

Do not operate without discharge chute, mulch kit, operator controlled discharge chute (OCDC), or entire grass catcher installed.

Front Baffle

52V - 424402

61V - 424403

Turbo Baffle

52V - 424211

61V - 424212

2. Remove the discharge chute from the cutter deck.

See Figure 2-1.

- note -

Do not discard the discharge chute or mounting hardware. The discharge chute MUST be reinstalled any time the grass catcher has been removed from the machine.

3. Remove the right side belt cover to gain access to the spindle assembly. Remove the front u-nut from the cutter deck bracket. See Figure 2-1.

- note -

Retain the original belt cover. This cover MUST be reinstalled any time the complete catcher system is removed.

UNDER SIDE OF vELOCITY-PLUS

CUTTER DECK SHOWN

Figure 2-2. Grass Catcher Baffles

- note -

Do not discard the original "Custom-Cut" or "Turbo" baffles. These baffles may be reinstalled any time the grass catcher has been removed from the machine.

6. Install the blower mounting bracket to the deck using 1/2-13 x 1-1/2" hex head bolts (p/n 04001-71),

1/2" spring lockwashers (p/n 04030-06), and 1/2-13 elastic stop nuts (p/n 04021-07). Do not fully tighten the hardware at this time. See Figure 2-4, Page 4.

2

Section 2

7. Install the blower assembly to the mounting bracket and secure with the mounting pin. See Figure 2-5,

Page 4.

8. Align the blower assembly with the discharge opening of the cutter deck. Tighten the hardware for the mounting bracket. See Figure 2-5.

9. Install the quick pin through the rear hole in the discharge chute mounting bracket. See Figure 2-5.

10. Install the belt to the spindle pulley. When replacing the belt. See Figure 2-3.

BACK SIDE

IDLER PULLEY

BLOWER

PULLEY

FRONT SIDE

IDLER PULLEY

SPINDLE

PULLEY

Figure 2-3. Belt Routing

11. Install the new belt covers and secure. See items number 1 and number 21 on page 10 of the Blower

Mounting Components section in this manual for proper installation.

R

3

R

Section 2

REAR OF

CUTTER DECK

DISCHARGE CHUTE OPENING

FRONT OF

CUTTER DECK

vIEW FROM RIGHT SIDE

OF CUTTER DECK

Figure 2-4. Blower Mounting Post Install

BLOWER

ASSEMBLY

QUICK

PIN

Figure 2-61"GC-STT install art

HAIR

PIN

MOUNTING

BRACKET

MOUNTING PIN

TIGHTEN MOUNTING

BRACKET HARDWARE

2006 GC-STC-V install art 3

RIGHT SIDE OF

CUTTER DECK SHOWN

(Note: Some parts not shown for viewing purposes.)

Figure 2-5. Blower Installation

4

Section 2

12. Install the hopper mounting brackets (p/n 451512) to the outside of the frame on the rear of the machine using 3/8-16 x 1" hex head bolts (p/n 04001-19) and

3/8-16 elastic stop nuts (p/n 04021-09). See Figure

2-8, Page 6 for all STT models and Figure 2-9, Page

7 for all SCZ models.

13. Install the hopper hood assembly onto the catcher frame assembly and secure with 3/8-16 x 2-1/4" hex head bolts (p/n 04001-46) and 3/8-16 elastic stop nuts (p/n 04021-09) in the mounting holes. See

Figure 2-8, Page 6 or all STT models and Figure

2-9, Page 7 for all SCZ models.

14. Install the catcher support bracket onto the rear of the machine and secure with 5/16-18 x 1" carriage bolts (p/n 04003-04) and 5/16-18 serrated flange nuts (p/n 04019-03) for all STT models or existing hardware for all SCZ models. See Figure 2-6 for STT or Figure 2-7 for SCZ.

Catcher Support Bracket

Figure 2-6. GC-Stt Support Bracket Install

-note-

The catcher support bracket for the SCZ61V is included with the 9079 Installation Kit.

Catcher Support Bracket

Existing

Hardware

Existing

Hardware

Figure 2-7. GC-SCZ Support Bracket Install

15. Install the heat shield to the hopper hood assembly and catcher frame assembly. Secure using the hardware specified in Figure 2-8, Page 6 for all STT models and Figure 2-9, Page 7 for all SCZ models.

16. Install adapter (p/n 461723) to the blower assembly and secure with the strap.

17. Install the hose from the blower assembly to the hopper hood. Secure using the 8-1/2" clamps.

-note-

When installing this catcher on an STT equipped with an air-cooled engine the discharge hose should be shortened.

18. Install the bag assemblies.

19. Install the Installation Kit as outline in the instruction sheet included with the Installation Kit.

20. Operate and test.

R

5

R

6

Section 2

Hood Assembly

1

5

4

3

2

4 4

4

3

3

4

5

4

3

Catcher Frame

3

Heatshield

1

Liquid

Cooled

Only

8

7

6

4

5

6

7

8

Item # Part #

1 04001-46

2

3

04001-19

04021-09

04030-04

04041-07

04066-03

423670

451512

Description

Bolt, Hex Head 3/8-16 x 2-1/4"

Bolt, Hex Head 3/8-16 x 1"

Nut, Elastic Stop 3/8-16

Lockwasher, 3/8 Spring

Flatwasher, 3/8-.391 x .938 x .105

Quick Pin

Spacer, Hitch

Hitch Bracket Weldment

Figure 2-8. GC-Stt Hopper Installation

6

Section 2

Hood Assembly

6

5

4

3

2

4 4

4

3

3

4

5

4

3

Catcher Frame

3

Heatshield

1

3

2

3 Briggs &

Stratton

Models

Only

2

7

6

4

5

6

7

Item # Part #

1 04001-46

2

3

04001-19

04021-09

04030-04

04041-07

04066-03

451512

Description

Bolt, Hex Head 3/8-16 x 2-1/4"

Bolt, Hex Head 3/8-16 x 1"

Nut, Elastic Stop 3/8-16

Lockwasher, 3/8 Spring

Flatwasher, 3/8-.391 x .938 x .105

Quick Pin

Hitch Bracket Weldment

Figure 2-9. GC-SCZ Hopper Installation

7

R

R

Section 3

3.1 GRASS CATCHER REMOvAL

INSTRUCTIONS

REMOVE

Prepare the machine so there is easy and safe access to the work area. Park the machine on a flat, level surface and apply the parking brake. Remove the ignition key and disconnect the positive and negative cables from the battery. Maintain all safety related work procedures. Always wear hand and eye protection.

1. Remove the bag assemblies from the grass catcher.

2. Remove the rubber strap holding the adapter to the blower assembly and the large quick pin securing the blower to the discharge mounting bracket. See

Figure 3-1.

3. Remove the belt, pin, hair pin and large quick pin securing the blower assembly to the cutter deck and remove the blower assembly. See Figure 3-1.

ADAPTER

PULL HOOD

5.

Figure 3-2. Removing the Hood Assembly

With help from an assistant, remove the hood assembly.

BLOWER

ASSEMBLY

QUICK PIN

PIN & HAIR PIN

WARNING

Do not operate without discharge chute, mulch kit, operator controlled discharge chute (OCDC), or entire grass catcher installed.

MOUNTING

BRACKET

2006 GC-STC-V removal art 1

RIGHT SIDE OF

CUTTER DECK SHOWN

(Note: Some parts not shown for viewing purposes.)

6. Re-install the side discharge chute to the opening on the cutter deck. Replace the two (2) outside mounting bolts on the discharge chute with the clevis pins (p/n 04064-15) and rue cotter pins (p/n 04069-

03). See Figure 3-3.

7. Re-install the cutter deck belt cover.

DISCHARGE

CHUTE

4.

Figure 3-1. Removing the Blower Assembly

Remove the two (2) pins holding the hood assembly to the mounting brackets on the rear of the machine.

See Figure 3-2.

CLEVIS PIN

P/N 04064-15

CLEVIS PIN

P/N 04064-15

RUE COTTER PIN

P/N 04069-03

GC-STC-V removal art 3

Figure 3-3. Reinstalling the Discharge Chute

8

Section 4

MAINTENANCE

4.1 MAINTENANCE CHART - RECOMMENDED SERvICE INTERvALS

HOURS

Break-In 8 20 40 100 200 500 Procedure

(First 10)

X

X

X

X

X

X

X

X

X

X

Check all hardware for tightness

Inspect hose and adapter

Check belt for proper alignment

Inspect fabric bags

*Check screen in hopper

Inspect hose and adapter

Inspect fabric bags

Check condition of blower

*Apply grease to blower bearings

Check belt for proper alignment

Comments

Remove debris from screen

See figure below

* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.

GREASE FITTING

ON BEARING HOUSING

R

GREASE FITTING

ON BEARING HOUSING

BEHIND PULLEY

R

Section 5

ILLUSTRATED PARTS LIST

4.1 SCAG APPROvED ATTACHMENTS AND ACCESSORIES.

Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved for use on this machine.

10

Section 5

NOTES

R

11

39

45

R

Section 5

R

DANGE

ROTA TING

BLO WER

BLAD

ES

STO P EN GINE

EN TERI

BEF ORE

HUTE

NG C

CON

TACT CAN INJU

RE

GC-STT / SCz BLOWER HOUSING ASSEMBLY

4

2

1

8

48

49

9

10

50

14

11

9

7

11

12

27

44

10

47 10

14

15

43

42

41

34

40

3

26

17

OPERA

RE

AD

OPE

WA

TING

RN

OR

'S M

AN

L

ING

RE

18

25

19

16

28

20

41

21

38

35

17

27

5

46

24

14

ROTA

TING

BLAD

DISCHARG

DAN

GER

AND

TE MOWE

R

BLOWER

LE

D

29

R

DANGE TAT

STO

ING

BL

P E

AD

NG

OW

ES

INE

BE

CA

N IN

E

JUR

E

14

15

17

11

12

22

23

24

14

13

14

11

6

30

33

32

37

31

31

47

2005 GC V+ Blower Assembly

35 34 45

36

12

Section 5

GC-STT / SCz BLOWER HOUSING ASSEMBLY

Ref.

No.

36

37

38

39

40

31

32

33

34

35

26

27

28

29

30

21

22

23

24

25

46

47

48

49

50

41

42

43

44

45

16

17

18

19

20

11

12

13

14

15

8

9

6

7

10

3

4

1

2

5

Part No.

461928

483182

483189

04043-04

43575

483402

04019-04

04001-136

483391

461931

04003-12

04063-06

461796

483034

04021-10

461930

421319

48136-02

48135-15

482298

04067-07

481547

04019-02

04001-59

483392

483393

481428

483223

04024-02

04021-05

04041-07

43277

483209

04021-09

04030-04

424361

04003-05

04001-54

04001-81

04001-21

04012-04

461932

481522

43212

04019-03

461723

451821

04062-04

424367

04066-04

Description

Pin, Ring 2-1/4" Long

Lanyard, Deck Height Pin

Nut, Serr. Flange 1/4-20

Bolt, Hex Head 1/4-20 x 1-1/4"

Decal, Blower

Decal, Rotating Blower

Grip, Blower Lever

Cap, Square

Nut, Push On 3/8 Thread

Lock Nut, 3/8-16

Flatwasher, 3/8-.391 x .938 x .105

Spacer

Pulley, Idler 4" Dia.

Nut, Elastic Stop 3/8-16

Lockwasher, 3/8-16

Plate, Catcher Mounting

Bolt, Carr. 3/8-16 x 1-1/2"

Bolt, Hex Head 3/8-16 x 3" - 52"

Bolt, Hex Head 3/8-16 x 3-1/2"

Bolt, Hex Head 3/8-16 x 1-3/4"

Idler Arm Assembly

Belt, GC-STT-61V

Pulley, 3-1/2" O.D., GC-STC

Washer, 3/8 Hardened

Pivot, Idler

Decal, Belt Cover

Nut, Serr. Flange 3/8-16

Bolt, Hex Head 3/8-16 x 1-1/2 Gr. 8

Decal, Danger

Blower Housing Weldment

Bolt, Carr. 5/16-18 x 3/4" Gr. 5

Key, 1/4 x 1/4 x 1-1/2"

Fan Weldment

Bearing Assembly

Nut, Elastic Stop 5/16-18

Blower Housing Assembly, GC-STT

Cover, Blower Housing

Clamp, 8-5/8" Max Dia.

Hose, 8.00" Dia. x 68" Long

Pulley, 4-3/4" O.D. - 1" Bore

Set Screw, 5/16-18 x 3/8"

Frame, Blower Mount

Spring, Main Drive

Spacer

Nut, Serr. Flange 5/16-18

Adapter w/Strap

Receiver Weldment, Mounting Post

Hair Pin Cotter, .177 x 3-1/4"

Dust Shield

Quick Pin, 5/16" Dia.

13

R

R

GC-STT / SCz BLOWER MOUNTING COMPONENTS

Section 5

1

2

UNDER SIDE OF vELOCITY-PLUS

CUTTER DECK SHOWN

16

16

3

10

4

5

11

6

7

8

12

13

6

9

10

28

25

26

27

25

24

25

26

24

23

23

21

20

16

18

17

22

14

15

15

19

RIGHT SIDE OF

CUTTER DECK SHOWN

2006 GC-STC-V BMC

14

Section 5

GC-STT / SCz BLOWER MOUNTING COMPONENTS

22

23

24

25

26

27

28

Ref.

No.

16

17

18

19

20

11

12

13

14

15

21

8

9

6

7

10

3

4

1

2

5

Part No.

483227

04029-04

483223

04021-08

461723

04040-14

48137-04

04001-59

481625-01

04064-15

04069-03

04067-07

481547

482377

04012-04

04021-09

04030-04

04041-07

04003-11

461894

462418

484368

04110-03

04003-23

04001-09

04040-15

04021-10

424403

424212

Description

Belt Cover, GC-STT - 61"

Wingnut, Plastic 3/8" Small

Cap, Square Vinyl

Nut, Elastic Stop 1/4-20

Adapter, Blower GC-STT includes item #7

Flatwasher, 1/4-.312 x .750 x .065

Rubber Strap 7-3/4"

Bolt, Hex Head 1/4-20 x 1-1/4"

Knob W/Stud, 3/8-16 x 1-1/4"

Clevis Pin, 5/16 x 1-1/2"

Pin, Rue Cotter 5/16 Dia.

Pin, Ring 1/2 x 2-1/4"

Lanyard

Pulley, 5-1/2" Dia. - 1.125" Bore

Setscrew, 5/16-18 x 3/8"

Nut, Elastic Stop 3/8-16

Lockwasher, 3/8"

Flatwasher, 3/8-.391 x .938 x .105

Bolt, Carr. 3/8-16 x 1-1/4" Grade 5

Mounting Post Weldment, Blower

Belt Cover Assembly, GC-STT-61V w/Cap

Cap, Spindle (not shown)

U-Nut

Bolt, Carriage 3/8-16 x 1"

Bolt, Hex Head 5/16-18 x 1"

Flatwasher, 5/16-.375 x .875 x .083

Nut, Elastic Stop 5/16-18

Baffle, Front 61" Deck

Baffle, Turbo 61" Deck

R

15

3

41

42

30

32

29

R

Section 5

40

GC-STT / SCz BAG SUPPORT COMPONENTS

1

6

2

3

4

5

9

4 33

8

11

33

32

31

11

5

24

9

18

9

16

25

43

40

5

22

16

21

23

16

21 22

19

13

13

23

19

16

20

59

5

18

9

16

4

16

5

59

14

4

9

34

44

9

34

31

9

34

34

46

9

STT61V Only

49

47 48

13

45

STT61V-28CAT / SCZ61V

49

55

58

56

57

11

51

27

26

11

11 34

9

52

36 34

28

12

15

39

5

17

54

38

36

35

5

34

9

50

10

37

9

53

50

37

FRAME

16

Section 5

GC-STT / SCz BAG SUPPORT COMPONENTS

Ref.

No.

38

39

40

41

42

33

34

35

36

37

28

29

30

31

32

23

24

25

26

27

18

19

20

21

22

13

14

15

16

17

8

9

10

11

12

3

4

5

1

2

6

7

48

49

50

51

52

43

44

45

46

47

53

54

55

56

57

58

59

Part No.

43277

425831

425829

48135-15

48136-02

482422

482421

04001-10

04021-10

04040-15

04041-11

04030-04

423436

423828

04001-19

451596

04001-31

482409

04010-25

04021-01

423302

04090-02

04041-19

04001-32

04041-01

461408

04001-117

425830

04021-09

423670

04001-46

04003-04

04001-20

04001-135

423690

04019-04

04019-03

43546

482304

425828

43212

04021-05

04001-08

04090-03

451026

422586

04067-06

481737

9009

451512

451674

423435

04066-03

425498

04021-11

04040-11

04001-117

452175

425832

Description

Screen, Catcher Hood

Pop Rivet, 3/16 x .652

Flatwasher, 3/16-.196 x .469 x .048

Bolt, Hex Head 3/8-16 x 1-1/4"

Flatwasher, 3/8-.391 x .938 x .105

Hood Assembly, GC-STT (includes items 1, 2 & 3 and items 2 & 15 on page 15)

Bolt, Hex Head 7/16-14 x 1-3/4"

Hinge, Upper LH

Nut, Elastic Stop 3/8-16

Spacer, Hitch

Bolt, Hex Head 3/8-16 x 2-1/4"

Bolt, Carriage 5/16-18 x 1.00"

Bolt, Hex Head 3/8-16 x 1-1/2"

Bolt, Hex Head 3/8-16 x 1-3/4" Grade 8

Support Bracket, Catcher (STT, STT61V-28CAT)

Nut, Serrated Flange 3/8-16

Nut, Hex Serrated Flange 5/16-18

Bushing, Hopper Pivot

Spring, Hood Hinge

Hinge, Lower LH

Spacer

Locknut, 3/8-16

Spacer

Hinge, Upper RH

Hinge, Lower RH

Hose, 8" Dia. x 53"

Clamp, 8-5/8" Max Dia.

Tube, Filler

Elbow

Bolt, Hex Head 5/16-18 x 1-1/4"

Nut, Elastic Stop 5/16-18

Flatwasher, 5/16-.375 x .875 x .083

Flatwasher, 3/8- .406 x 1-1/2" x .179

Lockwasher, 3/8" Spring

Bolt, Hex Head 3/8-16 x 3-3/4"

Tube, Upright

Bolt, Hex Head 3/8-16 x 1"

Bolt, Hex Head 3/8-16 x 2-1/2"

Support Weldment, Weights

Latch

Screw, #10-32 x 3/4"

Nut, Elastic Stop #10-32

Bolt, Hex Head 5/16-18 x 3/4"

Rivet, 3/16 x .402 POP

Support Weldment, Front Weights (STT Only)

Clamp, Bar

Pin, 1/2 x 6-1/4"

Lanyard, Weight Pin

Weight Assembly

Hitch Bracket Weldment

Support Weldment, Bag Frame

Heat Shield

Quick Pin

Support Bracket, GC (SCZ Only)

Nut, Elastic Stop 7/16-14

Flatwasher, 7/16-.500 x 1.250 x .083

Bolt, Hex Head 7/16-14 x 1-3/4"

Support Weldment, Front Weights (STT61V-28CAT, SCZ)

Guard, GC Hinge

17

R

R

GC-STT / SCz BAG SUPPORT AND SEAL

Section 5

2

8

9

10

11 12

7

5

6

4

13

3

18

390STT0201

1

Section 5

GC-STT / SCz BAG SUPPORT AND SEAL

Ref.

No.

8

9

6

7

10

3

4

1

2

5

11

12

13

Part No.

04090-02

482321

04021-02

423312

04003-02

04001-08

04019-03

04021-10

04040-15

423197

04003-12

423198

482569

Description

Pop Rivet, 3/16 x .652

Seal, Hood

Lock Nut, 1/4-20 Center Lock

Retainer, Seal

Bolt, Carr. 1/4-20 x 3/4"

Bolt, Hex Head 5/16-18 x 3/4"

Nut, Serrated Flange 5/16-18

Nut, Elastic Stop 5/16-18

Flatwasher, 5/16-.375 x .875 x .083

Tube, Bag Support

Bolt, Carr. 5/16-18 x 3/4"

Mount, Bag Frame Tube

Bag Assembly, GC-STT

R

19

R

Section 5

GC DECALS

483402

482275

__________ __________ __________ __________

__________ __________ __________ __________

__________ __________ __________ __________

__________ __________ __________ __________

483044

481327

483392

483392

483391

483391

20

483393

483393

LIMITED WARRANTY- COMMERCIAL ACCESSORY

Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of

Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service

Dealer without charge for parts and labor.

The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within the warranty period. The expense of delivering the accessory to the dealer for warranty work and the expense of returning it back to the owner after repair or replacement will be paid for by the owner. Scag’s responsibility in respect to claims is limited to making the required repairs or replacements, and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag machine.

Proof of purchase will be required by the dealer to substantiate any warranty claim. All warranty work must be performed by an Authorized Scag Service Dealer.

This warranty is limited to 90 days from the date of original retail purchase for any Scag accessory that is used for commercial purposes, or any other income-producing purpose including rental use.

The warranty for the grass catcher blower assemblies (excluding the belt) is limited to 1-year from the date of original retail purchase. 90 Days for rental use.

This warranty does not cover any accessory that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator's Manual.

The warranty does not apply to any damage to the accessory that is the result of improper maintenance, or to any accessory or parts that have not been assembled or installed as specified in the Operator's Manual.

The warranty does not cover any accessory that has been altered or modified. In addition, the warranty does not extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or durability. This warranty does not cover engines and electric starters, which are warranted separately by their manufacturer.

Scag Power Equipment reserves the right to change or improve the design of any accessory without assuming any obligation to modify any accessory previously manufactured.

All other implied warranties are limited in duration to the 90 day warranty period. Accordingly, any such implied warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety after the expiration of the appropriate ninety day warranty period. Scag’s obligation under this warranty is strictly and exclusively limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone to assume for them any other obligation. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense for gasoline, oil, expense of delivering the machine to an Authorized Scag Service Dealer and expense of returning it back to the owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of the mower, loss of time, or inconvenience. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.