Eneo DTR-2009/250CD Operating instructions

Operating Instructions
Digital Video Recorder
Models: DTR-2009/250CD, DTR-2016/250CD,
DTR-2009/500CD, DTR-2016/500CD,
DTR-2009/750CD DTR-2016/750CD
Safety instructions
EMC class
► This digital video recorder (DVR) is a class A device in accordance with EN 55022.
► This device may cause interference to other equipment in domestic use. In such cases the persons operating the DVR are required to provide appropriate countermeasures, for which they themselves bear the cost.
Importance of these Operating Instructions
► Please read the safety instructions and the other information contained in the Operating Instructions before
connecting up and operating the DVR.
► The Operating Instructions should be kept in a safe place for later reference.
Ambient conditions
► The DVR should be protected against excessive heat, dust, moisture and vibration.
► The DVR may only be operated at temperatures between +5°C and +40°C, and up to a maximum air
humidity of 90%.
► The DVR may only be operated indoors, and must be protected against ingress of water and moisture.
Care of the DVR
► Never switch on the DVR when moisture has penetrated it. In such cases, have the DVR checked by a
qualified service engineer.
► Do not place any heavy objects on the DVR.
► Never cover over the DVR‘s vents.
► Never insert metal objects or any other items into the vents. This may permanently damage the DVR.
► The housing may only be opened by authorised persons. Repairs may only be carried out by qualified
service personnel.
► The DVR must be disconnected from the power supply before its housing is opened.
Getting started with the DVR
► When laying the connecting cables, make sure no weight is placed on them, that they are not kinked or
damaged, and that no moisture can penetrate them..
Cleaning
► The housing of the DVR may only be cleaned with a moisture (not wet) cloth.
► Use only a mild detergent. Do not use solvent-containing detergents or petrol. This could permanently
damage the surface finish.
Spare parts
► Use only original spare parts from Videor Technical GmbH..
DTR-20XX
Table of contents
Overview
Package contents
Basis functions
Features
Requirements for operation
Control options
Connections on the rear
Front panel controls
Key to controls
Function buttons
PTZ camera functions
Playback functions
Remote control functions
Playback functions
Menu overview
Accessing the menus
Accessing the Display menu
Accessing the PTZ menu
Accessing the Setup menu
Accessing the Search menu
Getting started
Checklist for DVR operation
Connecting the remote control and DVR
Switching on the DVR
Switching off the DVR
Administration
Saving your system setup Loading your system setup
Deleting recordings
Downloading software updates
Hiding from specific users
Restoring factory defaults
Determining the memory requirement of a recording
Searching for recordings
Using calendar search
Using event log search
Using text-in search
Using motion search
Copying recordings
DTR-20XX
7
7
7
7
7
7
8
9
10
10
10
10
11
11
12
14
14
14
15
15
16
16
16
17
17
18
18
18
18
19
19
19
20
21
22
23
24
25
26
Table of contents
Menu descriptions – Setup menu
27
System – Information
28
System – Date/Time
29
System – Storage30
System – User32
System – Shutdown33
System – Log out user1...33
Network – Network33
Network – Notification
36
Devices – Camera37
Devices – Audio38
Devices – Alarm-Out39
Devices – Display
40
Devices – Remote Control
41
Record – Record
42
Record – Schedule
43
Record – Pre-Event
44
Record – Archive
45
Event – Alarm-In
46
Event – Motion Detection
48
Event – Video Loss
50
Event – Text-In
52
Event – System Event
54
Event – Event Status
56
Specifications DTR-2009
57
Specifications DTR-2016
59
Accessories
61
Supported PTZ cameras
62
Index
63
Notes on disposal
66
DTR-20XX
Overview
Package contents
●
●
●
●
●
●
●
●
●
Digital video recorder (DVR)
Mains power cord
Operating instructions
RAS (Remote Administration System) software on CD
Operating instructions for RAS software on paper and CD
Mounting kit for rack installation
Screws for attaching SCSI Connector
Mounting screws and guide for installation of hard disk drives
Infrared remote control
Basis functions
●
●
●
●
Recording of video images from multiple cameras
Event-triggered start of recording
Video playback
Search for specific video sequences
Features
●
●
●
●
●
●
●
●
●
●
●
●
MPEG-4 compression / duplex mode
9 or 16 loop-through inputs / VGA, S-VHS/FBAS outputs
Audio and alarm inputs / outputs
Max. recording speed: 100 field images per sec (PAL)
Memory capacity 250 GB / 500 GB / 750 GB
Maximum video resolution 720 x 576 pixels
SCSI port for archiving / memory expansion
Various recording criteria possible
Archiving/image transfer via USB and CD-RW
ATM/POS text display / 2x to 4x digital zoom
Telemetry control functions via RS-485 port
Network port (Ethernet) / IR remote control
Requirements for operation
●
●
●
●
Digital video recorder DTR connected
At least 1 camera connected
At least 1 monitor connected
Mouse connected, if DVR is to be controlled by mouse
Control options
●
●
●
●
Front panel
Remote control
Mouse
RAS program
DTR-20XX
Connections on the rear
Note: Connections optionally for NTSC or PAL operation.
1
2
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
VIDEO OUT
SPOT 1
SPOT 2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SVHS OUT
SPOT 3
SPOT 4
VIDEO IN
LOOP
AUDIO IN 1
AUDIO IN 2
AUDIO IN 3
AUDIO IN 4
AUDIO OIT
AI1 AI2 AI3 AI4 GND AI5 AI6 AI7 AI8 GND AI9 AI10 AI11 AI12 GND AI13 AI14 AI15 AI16 GND
AO1 AO2 AO3 AO4 GND AO5 AO6 AO7 AO8 GND AO9 AO10 AO11 AO12 GND AO13 AO14 AO15 AO16 GND
ARI GND
RS-485
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
18
17
USB
16
15
14
1
RS-232C
12
VGA
11
SCSI
10
9
NETWORK
8
No.
Designation
Functions/connections
Example devices
1
VIDEO IN 1-16
Max. 16 video channels
Cameras
2
LOOP 1-16
Max. 16 loop-through video channels
Cameras
3
SVHS OUT
S-VHS output
Monitors
4
VIDEO OUT
Video output
Monitors
5
SPOT1 - SPOT4
Max. 4 video outputs
Spot monitors
6
RS-485
External interface
Keyboard, PTZ camera
7
NETWORK
Network
Network cable
8
ARI/GND
Reset alarm
with external signal
Switch
9
SCSI
External storage media
Hard disk
10
AO1 - AO16
Alarm outputs for external devices
Siren, flashing light
11
VGA
PC monitor
PC monitor
12
RS-232C
External interface
Modem
13
USB
External interface
Drive, mouse
14
Reset switch
Reset to factory defaults
-
15
AI1 - AI16
Alarm inputs for external devices
Sensors
16
AUDIO OUT
Audio output
Amplifier, speakers
17
AUDIO IN 1 AUDIO IN 4
Max. 4 Audio inputs
Microphone
18
Power supply
Mains power connection
-
7
DTR-20XX
Front panel controls
The following diagram and table shows the controls on the front panel of the DVR:
1
2
1
4
2
3
4
5
5
6
7
6
8
PANIC
JOG
CAMERA
9
10
11
12
DISPLAY
SEQUENCE
FREEZE
SPOT
MENU
ALARM
ZOOM
PTZ
13
14
15
SEARCH
PLAY/PAUSE
RW
FF
BACKWARD
FORWARD
16
HDD
NETWORK
14
No.
Designation
1
12
POWER
11
10
9
8
7
Function
1
USB ports
2
Eject built-in CD-RW writer
3
1 to 16
● Select cameras
● Enter passwords
4
Menu navigation
Navigation and selection within the menu
5
PANIC
Start/end panic recording
6
Shuttle ring
Infinitely adjust playback speed
7
Jog dial
● Change size of frame in picture-in-picture mode
● Change numerical values in Setup menu
● Frame-by-frame playback in Play mode
Playback functions (primary assignment)
8
PTZ camera functions (secondary assignment)
9
POWER
Power-on indicator when DVR is in operation
10
NETWORK
Indicates Ethernet or modem connection
11
HDD
Indicates hard disk operation
12
DISPLAY, SEQUENCE,
FREEZE, SPOT, ZOOM,
PTZ
Function buttons
13
ALARM
● Reset alarm
● View event list
14
MENU
Open/quit menu structure
DTR-20XX
Key to controls
Function buttons
Element
Function
● Change display mode
● Switch video input by pressing and holding down button
Sequence On/Off
Freeze On/Off
PTZ camera functions On/Off
Zoom On/Off
Spot monitor assignments
PTZ camera functions
Element
Function
Zoom in
Zoom out
Close-up
Wide-angle
Save preset
Load preset
Playback functions
Element
Function
● Select Search/Play function
● Stop playback
Frame-by-frame rewind
Fast rewind
Start/pause playback
Fast forward
Frame-by-frame forward
10
DTR-20XX
Remote control functions
The following diagram and table shows the functions on the remote control:
Select System ID
ID
SPOT
1
2
DISPLAY
SEQUENCE
12
11
3
4
FREEZE
ALARM
CAMERA
1
2
3
5
6
7
8
9
10
11
12
15
16
13
14
TRIPLEX
AUDIO
4
FOCUS
2
BOOK MARK CLIP COPY
4
SET
10
1
PRESET
ZOOM
VIEW
MENU
9
PTZ
5
ZOOM
PANIC
6
8
DIGITAL VIDEO RECORDER
Remote Controller
7
No.
Designation
Function
1
SPOT 1 - 4
Spot monitor assignments
2
ALARM
● Reset alarm
● View event list
3
1 to 16
● Select cameras
● Enter passwords
4
PTZ camera functions
5
PTZ
PTZ camera functions On/Off
6
ZOOM
Zoom On/Off
7
Playback functions
8
PANIC
Start/end panic recording
9
Menu navigation
Navigation and selection within
the menu
10
MENU
Open/quit menu structure
11
12
No function
DISPLAY, SEQUENCE,
FREEZE
Function buttons
Playback functions
Element
Function
● Select Search/Play function
● Stop playback
Pause playback
Start playback
Fast rewind
Fast forward
Frame-by-frame rewind
Frame-by-frame forward
DTR-20XX
11
Menu overview
The following illustration shows the structure of the complete menu tree that is accessible using the mouse
control:
Display
Camera
1. CAM1
2. CAM2
3. CAM3
PIP
Left-Top
Left-Bottom
Right-Top
Right-Bottom
Size 1/16
Size 1/9
Size 1/4
2x2
3x3
4x4
Previous Group
Next Group
Edit Group
Sequence
Freeze
Zoom...
PTZ...
Spot Monitor...
Toggle VGA ...
12
Camera
Spot Monitor...
Toggle VGA ...
Exit Group Edit
Speed
Auto Pan
Tour
Pattern
Device Menu
Light
Pump
Wiper
Power
Aux.
Move to Origin
Spot Monitor
Toggle VGA ...
Exit PTZ
Select Spot Monitor
Spot Monitor 1
Spot Monitor 2
Spot Monitor 3
Spot Monitor 4
DTR-20XX
Menu overview, continued
The following illustration shows the structure of the complete menu tree that is accessible using the mouse
control:
Setup menu...
Search
System
Information
Date/Time
Storage
User
Shutdown...
Log out user1...
Network
Network
Notification
Devices
Camera
Audio
Alarm-Out
Display
Remote Control
Record
Record
Schedule
Pre-Event
Archive
Event
Alarm-In
Motion Detection
Video Loss
Text-In
System Event
Event Status
Go to the First
Go to the Last
Go to the Date/Time...
Calendar Search...
Event Log Search...
Text-In Search….
Motion Search...
Clip-Copy...
Print...
Zoom...
Slow Play
Data Source
Exit Search
DTR-20XX
x1
x1/2
x1/3
x1/4
x1/6
x1/8
Record
Archive
13
Accessing the menus
Accessing the Display menu
Requirement:
● The current camera image is shown in full image or quad image.
Step
Action
Access using
Key sequence/menu path
Device
1
Open Display menu...
Remote control
Mouse
Display
Access to submenu via Device/Remote Control
Submenu
Camera image
Key sequence
Change Display modes (PIP, 2x2, 3x3, 4x4)
Without frame
Previous/Next Group
Without frame
Edit Group
With frames
Change position of image-in-image
Without frame
Change size of image-in-image
Without frame
Jog dial
Action
Access using
Key sequence/menu path
Open PTZ menu...
Device
Result: Menu of the configured PTZ
camera is shown.
Remote control
PTZ
Mouse
PTZ...
....
>
Accessing the PTZ menu
Requirement:
● A PTZ camera is connected and configured.
● Current camera image is shown as a full image.
Step
1
14
>
>
MENU
DTR-20XX
Accessing the menus, continued
Accessing the Setup menu
Requirement:
● The current camera image is shown in full image or quad image.
Step
1
2
Action
Access using
Open Setup menu...
Device
Key sequence/menu path
Result: Prompt for user name and
password.
Remote control
MENU
Mouse
Setup menu...
Log in as user.
User name: admin
Password: (blank)
Note: Use default access data only for
first-time access.
Accessing the Search menu
Requirement:
● The current camera image is shown in full image or quad image.
Step
1
DTR-20XX
Action
Access using
Key sequence/menu path
Open Search menu...
Device
>
Result: Search for recorded images is
activated.
Remote control
>
Mouse
MENU
Search
15
Getting started
Checklist for DVR operation
Step
Action
Menu path
1
Connect peripheral devices as per planned setup.
2
Specify menu language..
Setup menu... > System > Information
3
Adjust date and time..
Setup menu... > System > Date/Time
4
Set up user.
Setup menu... > System > User
5
Set up network and desired notification channels
(optional).
Setup menu... > Network > ...
6
Register peripherals with DVR.
Setup menu... > Devices > ...
7
Set up event types and associated responses.
Setup menu... > Event > ...
8
Set up recording parameters and schedule.
Setup menu... > Record > ...
Connecting the remote control and DVR
The remote control and DVR can be assigned an ID, because the ID of each DVR in the network must be
unique. The DVR will then only respond to the remote control with the matching ID.
● If the system ID in the DVR is 0, it will respond to the remote control regardless of the remote’s ID.
● If the system ID in the DVR is not 0, you must set the ID of the remote control identically.
Step
Action
Menu path
1
Set DVR system ID.
Setup menu... > System > Information
2
Match remote control to system ID by
pressing ID button on remote control.
3
Select relevant number on remote control.
16
DTR-20XX
Getting started, continued
Switching on the DVR
Requirement:
● The start-up preparations are complete.
Step
Action
1
Plug in DVR mains plug.
2
Switch on monitor.
Result: System starts up automatically and is ready to use.
Switching off the DVR
Requirement:
● You have accessed the Setup menu.
Step
1
2
DTR-20XX
Action
Shut down system.
Result: System shuts down automatically.
Menu path
Setup menu > System > Shutdown ...
After shutdown, disconnect the mains plug.
17
Administration
Saving your system setup
You can save your DVR’s setup data, including its network configuration.
Requirement:
● USB memory stick
Step
Action
1
Insert a USB memory stick into one of the USB
ports
2
Export your setup.
3
Specify a file name.
4
Export your setup.
Menu path
Setup menu... > System > Information >
Setup Export...
Export
Loading your system setup
You can load your stored DVR system setup with or without its network configuration.
Requirement:
● USB memory stick with stored setup
Step
Action
Menu path
1
Insert a USB memory stick into one of the USB
ports.
2
Import your setup.
3
Select the file name and, where appropriate, the
network configuration.
4
Import your setup.
Setup menu... > System > Information >
Setup Import...
Import
Deleting recordings
You can only delete all your recordings together. It is not possible to delete recordings from a specific time
period.
Step
1
18
Action
Menu path
Delete all recordings.
Setup menu > System > Information > Clear All
Data...
or
Setup menu > System > Storage > Information tab
> Using > Clear
DTR-20XX
Administration, continued
Downloading software updates
You can download software updates for your DVR from a USB memory stick.
Requirement:
● USB memory stick with latest software release
Step
Action
1
Insert a USB memory stick into one of the
USB ports.
2
Start update.
3
Install new release
Menu path
Setup menu... > System > Information > Upgrade...
Hiding from specific users
You can hide video images and camera data according to the preset user rights.
Step
Action
Menu path
1
Set camera Covert mode.
Setup menu... > Devices > Camera > Settings
2
Cancel ‘Covert Camera View‘ access for
specific users (groups).
Setup menu... > System > User
Restoring factory defaults
Before restoring the factory defaults, you should export your current system settings in case you need to reimport them later. (see Saving your system setup and Loading your system setup)
Step
Action
1
Shut down the system.
2
Disconnect the mains plug.
3
Push a paper clip into the Reset button (on the rear of the DVR) and hold it there.
4
Plug in the mains plug.
5
Wait for all the LEDs to flash 5 times (about 30 seconds).
6
Withdraw the paper clip.
DTR-20XX
19
Administration, continued
Determining the memory requirement of a recording
The amount of memory recorded video sequences will take up depends on the following factors:
● picture quality
● number of images per second
● duration
The memory requirement is calculated by this formula:
Memory requirement = picture size x duration of recording x images per second
Example calculation of CIF resolution (PAL):
Approx. memory space
Picture
quality
Picture
size
Duration of
recording
5 images/s
10 images/s
25 images/s
Basic
2.4 KB
24 hours
1.04 GB
2.07 GB
5.18 GB
Standard
4.8 KB
24 hours
2.07 GB
4.15 GB
10.37 GB
High
9.6 KB
24 hours
4.15 GB
8.29 GB
20.74 GB
Very high
14.4 KB
24 hours
6.22 GB
12.44 GB
31.10 GB
Example calculation of 2CIF resolution (PAL):
Approx. memory space
Picture
quality
Picture
size
Duration of
recording
5 images/s
10 images/s
Basic
4.8 KB
24 hours
2.07 GB
4.15 GB
10.37 GB
Standard
9.6 KB
24 hours
4.15 GB
8.29 GB
20.74 GB
High
19.2 KB
24 hours
8.29 GB
16.59 GB
41.47 GB
Very high
28.8 KB
24 hours
12.44 GB
24.88 GB
62.20 GB
20
25 images/s
DTR-20XX
Searching for recordings
Find first stored recording
Search
Go to the First
Find last stored recording
Search
Go to the Last
Find recording by date and time
Search
Go to the Date/Time...
Calendar search
For each camera the calendar search indicates:
● the days from which there are recordings
● the time ranges of recordings on those days
Search
Calendar Search...
Event log search
The event log search enables you to search for events based on specific criteria, such as:
● movements recorded by a specific camera
● alarm from a specific alarm input
● System events
Search
Event Log Search...
Text-in search
The text-in search enables you to search for recordings based on specific text inputs.
Search
Text-In Search…
Motion search
The motion search function can detect movements in recordings within defined zones for one camera. 2 types
of motion search are possible:
● Motion search: Search for movement in a defined zone.
● Museum search: Search for movement of a defined object.
Search
Motion Search...
Copying recordings
Recordings can be written to a CD or copied to a USB memory stick.
Search
DTR-20XX
Clip-Copy...
21
Using calendar search
Performing a calendar search
Step
1
Action
Menu path
Open calendar search.
Result: Calendar and time line are displayed.
2
Select day and time
3
Confirm input.
Search
Term
Search > Calendar Search...
Go
Calendar Search...
Symbol
Meaning
Date display
● Grey: No recording available
● White: Recording available
Hours display
● White: Recording available
Select a Segment
22
If the date and time on the DVR have been changed (such
as when switching to Summer time) there may be multiple
recordings for one time from the same camera. They are stored
in separate segments.
DTR-20XX
Using event log search
Performing an event log search
Step
1
2
3
4
Action
Menu path
Open event log search.
Result: The result of the last search is displayed.
Define criteria.
Search > Event Log Search...
Option...
Confirm input.
Result: List of search results is displayed.
Search
Select desired entry from list.
Search
Term
Event Log Search...
Symbol
Option...
Meaning
From First
Start date
To Last
End date
Check Time Overlap
Activates a system prompt if there are multiple recordings
for the same time range
Alarm-In
Alarm inputs in response to which a search for events is
to start
Motion
Cameras on which to search for motion detection
Video Loss
Cameras on which to search for video loss
Text-In
Text input devices on which to search for events
Record Channels
Cameras on which to search for events
Search for system events:
Setup menu > Event > System Event > Actions
DTR-20XX
23
Using text-in search
Performing a text-in search
Step
1
2
3
4
Action
Menu path
Open text-in search.
Result: The result of the last search is displayed.
Define text inputs.
Search > Text-In Search...
Option...
Confirm input.
Result: List of search results is displayed.
Search
Select desired entry from list.
Search
Term
Text-In Search…
Symbol
Option...
Meaning
From First
Start date
To Last
End date
Channels
Text input devices on which to search for events
Type of text input:
Any Text-In Product
Generic Text
Epson
No.
Numbers of text elements to search for
Keyword
Text element
Case Sensitive
Makes search case-sensitive
24
DTR-20XX
Using motion search
Performing a motion search
Step
Action
Menu path
1
Display desired camera in single frame.
Display > Camera > ...
2
Open motion search.
Search > Motion Search...
3
Enter settings for motion search.
Option...
4
5
Search
Term
Confirm input.
Search
Result: List of search results is generated.
Select desired entry from list.
Motion Search...
Symbol
Option...
Meaning
From First
Start date
To Last
End date
Type of search:
Type
Zone
Motion Search
Search for movement in a defined zone
Museum Search
Search for movement of a defined object
Definition of motion-sensitive zones for motion search or museum search:
See “Zone” on page 46.
Sensitivity of motion detection of:
1 (Dull)
Sensitivity
2
3
4
5 (Sensitive)
Min. Blocks
DTR-20XX
Motion search only (not museum search):
Specify in how many motion-sensitive blocks motion must be detected as
a minimum to trigger an alarm
25
Copying recordings
Copying recordings to CD or USB memory stick
Step
1
2
3
Search
Term
Data Source
Action
Menu path
Find desired recordings.
Note: Make a note of the data of the recordings you
want to copy.
Search > ...
Define settings.
Search > Clip-Copy...
Start copying.
Result: The recordings are copied.
Start
Clip-Copy...
Symbol
Meaning
Record
From First
Start date
To Last
End date
Channels
Assignment of cameras from which recordings are to be copied
Password
Use password, if desired
Destination medium:
Internal CD-RW
Dest.
USB CD-RW
1. USB Storage
2. USB Storage
3. USB Storage
File name
Name of file on destination medium
Verify After
Burning
Activates verification after burning
Progress
Copy status
26
DTR-20XX
Menu descriptions – Setup menu
The Setup menu has the following sub-menus:
System menu
On the “System” menu
● the basic settings are made
● users are administered
● the system is shut down
Network menu
On the “Network” menu the network settings are made. Network access provides
access to all the functions of the DVR via
● RAS (Remote Administration System), independent of Internet Explorer
The DVR can be configured so that alarms trigger a notification by e-mail or notify an
RAS.
Devices menu
On the “Devices” menu the connected peripheral devices are configured. Possible
peripherals are:
● Cameras
● Microphones and speakers (through amplifier)
● Sirens and signal lamps
● Monitors
● Remote control for PTZ
Record menu
On the “Record” menu the following settings are made:
● Recording quality
● Timer control
● Duration of pre-event recording
● Schedule and method of archiving
Event menu
On the “Event” menu the following settings are made:
● Assignment of alarm inputs to alarms
● Configuration of motion-sensitive zones individually for each camera
● Definition of text input device and assignment to alarms
● Response to undesirable events
The event status is additionally displayed.
DTR-20XX
27
Setup menu
System – Information
On the “Information” menu
● basic information is entered and displayed
● software updates are installed
● recorded data are deleted as required
Setup menu...
Term
System
Symbol
Information
Meaning
Site
Location of DVR
System ID
Identifier for remote control
● The remote control and DVR must be set to the same ID.
● If the system ID in the DVR is 0, it will respond to the remote
control regardless of the remote’s ID.
Language
Menu language
Version
Version of DVR software
Upgrade...
Starts installing latest version of software via USB port
Import...
Import setup
Export...
Export setup
Show System Log...
Show log of all actions and events
Recorded data
From
Date of oldest recording
To
Date of newest recording
Clear All Data...
Deletes all stored data
28
DTR-20XX
Setup menu, continued
System – Date/Time
On the “Date/Time” menu
● time and date settings are made
● dates of public holidays are entered
● time synchronisation is configured.
Setup menu...
Term
System
Symbol
Date/Time
Date/Time
Meaning
Date
Date
Format
Date display format
Time
Time
Format
Time display format
Time Zone
Local time zone
Use Daylight Saving Time
Activates use of summertime Daylight Saving Time
Setup menu...
Term
System
Symbol
Date/Time
Holiday
Meaning
No.
Number of entered public holiday
Date
Date of each desired public holiday
Setup menu...
Term
System
Symbol
Date/Time
Time Sync
Meaning
Automatic Sync
Activates synchronisation with time server
Time Server
IP address or domain name of time server
Interval
Synchronisation interval
Last Sync-Time
Time of last synchronisation
Run as Server
Activates use of the DVR as the time server
DTR-20XX
29
Setup menu, continued
System – Storage
On the “Storage” menu the status and usage of the available storage media is displayed.
Setup menu...
Term
System
Symbol
Storage
Information
Meaning
Type
Type of storage medium
Capacity
Size of storage medium
Format Storage medium usage >>
Information
Time range of recorded data >>
Format
Term
Symbol
Meaning
Use of storage medium:
Record
Use as
Archive
Not using
Activating permits:
Partition
CD/DVD burn
Format Reserves a data buffer as a separate
partition. This is essential for burning
CDs, and must be activated for a
storage medium with „Record“ usage..
Formatting deletes the recordings from the hard disk
Information
Term
Symbol
Meaning
Recorded data
From
Start date of recorded data
To
End date of recorded data
Clear
Delete all recordings
30
DTR-20XX
Setup menu, continued
Setup menu...
Term
System
Symbol
Storage
Meaning
Type
Memory type
Disk Bad
Data carrier status
Temperature
Temperature status
S.M.A.R.T.
Result of S.M.A.R.T. check
DTR-20XX
Status
31
Setup menu, continued
System – User
On the “User” menu the user groups and individual users are set up.
Setup menu...
Term
System
Symbol
User
Meaning
Group & User
Group field
Assignment of group access privileges
Table of possible group access privileges >>
Group & User
User field
Set password
+ Group...
Add a new group
+ User...
Add a new user
Set password
Auto Login
User to be logged in automatically
Auto Logout
Time after which logged-in user is automatically logged out
Table of possible group access privileges
Group access privilege
Meaning
Shutdown
May shut down the DVR
Upgrade
May install a new firmware version
System Time Change
May change the time setting
Data Clear
May delete recording data
Setup
May make changes anywhere on the Setup menu
Color Control
May change the picture settings
PTZ Control
May control PTZ cameras
Alarm-Out Control
May reset alarms
Covert Camera View
May view video images from covert cameras
System Check
May interrogate system status
Record Setup
May make changes to the Record menu
Search
May use Search mode
Clip-Copy
May copy video images
32
DTR-20XX
Setup menu, continued
System – Shutdown
Setup menu...
System
Shutdown...
System – Log out user1...
Setup menu...
System
Log out user1...
Network – Network
On the “Network” menu all settings required to ensure network access are made.
Setup menu...
Term
Network
Symbol
Network
Network
Meaning
Transmission bandwidth:
Transfer Speed
(bps)
bits per second
(ips)
images per second
Quality of picture transmission via network (PAL):
Quality
DTR-20XX
Very High
14.4 KB/picture
High
9.6 KB/picture
Standard
4.8 KB/picture
Basic
2.4 KB/picture
33
Setup menu, continued
Setup menu...
Term
Network
Symbol
Network
LAN
Meaning
Type of connection to DVR:
Type
Manual
Manual connection required input of:
● IP address
● Gateway
● Subnet Mask
DHCP
Automatic assignment of IP address of DNS
server
ADSL
(with
PPPoE)
Requires following input as specified by provider:
● ID
● Password
Note: Use of modem must not be activated.
DNS Server
Address of DNS server
Port Number Setup...
Definition of port numbers needed to access the DVR via the
RAS software
Setup menu...
Term
Enable
Network
Symbol
Network
Meaning
Enables modem use
Note: LAN type ADSL must not be enabled.
Baud Rate
Baud rate
Data
Number of data bits
Stop Bit
Number of stop bits
Parity
Parity
34
Modem
DTR-20XX
Setup menu, continued
Setup menu...
Term
Network
Network
Symbol
DVRNS
Meaning
Use DVR Name Service
Enables the DVR name service
DVRNS Server
IP address or domain name of DVRNS server
DVRNS = Digital Video Recorder Name Service
Port
Port for DVRNS
Use NAT
Enables NAT (Network Address Translation) use
DVR Name
Name by which the DVR is to be registered with the DVRNS
server
Check
Check DVR name for usability after entering
Help Desk
Information from help desk if DVRNS setting correct
DTR-20XX
35
Setup menu, continued
Network – Notification
On the “Notify” menu the method of notification is defined.
Setup menu...
Term
Network
Symbol
Notification
Mail
Meaning
Enable
Enables notification by e-mail
SMTP Server
IP address or domain name of SMTP server
Port
Port for SMTP server
Default is port 25.
Authentication
Login to SMTP server
Sender
E-mail address of sender
Recipient
E-mail address of recipient
Setup menu...
Term
Network
Symbol
Notification
Callback
Meaning
LAN
Enables notification of an RAS via LAN
No.
Number of IP address
IP Address
IP addresses of RAS PCs
Retry
Number of notification attempts by the DVR in the event of an
error
Modem
Enables notification of an RAS via modem
Remote Server Phone
Number
Telephone number of the modem on the notified RAS PC
Outside Line Call
Outside line code for external calls, if DVR’s modem is connected to a PABX system
Callback Phone Number
Telephone number of DVR’s modem
The RAS PC contacts the DVR on this number.
36
DTR-20XX
Setup menu, continued
Devices – Camera
On the “Camera” menu the cameras are configured.
Setup menu...
Term
Devices
Symbol
Camera
Settings
Meaning
No.
Activates the cameras
Title
Name of camera
Visibility of recordings and camera data depending on user access
privileges:
Use
Setup menu...
Term
Normal
All users see all camera data and all recordings
Covert 1
Users without relevant access see camera title, status
symbol, but no recordings
Covert 2
Users without relevant access see only camera title, but no
recordings
Devices
Symbol
Camera
PTZ
Meaning
No.
Number of camera
Product
PTZ camera type as per specified list
ID
Unique ID of PTZ camera
Port
Interface type of PTZ cameras
Settings as specified by PTZ camera manufacturer:
Baud Rate
Setup…
Data Bit
Stop Bit
Parity
DTR-20XX
37
Setup menu, continued
Devices – Audio
On the “Audio” menu the audio outputs are assigned to the cameras.
Setup menu...
Term
Devices
Symbol
Audio
Meaning
No.
Number of audio output
Associated Camera
Assignment of camera
Enable Audio-Out
Enables all audio outputs
38
DTR-20XX
Setup menu, continued
Devices – Alarm-Out
On the “Alarm-Out” menu the alarm outputs are configured.
● “Settings” tab: The alarm outputs are configured.
● “Schedule” tab: Time slots are defined in which the alarm outputs respond in specific ways.
Setup menu...
Term
Devices
Symbol
Alarm-Out
Settings
Meaning
No.
Number of alarm output
Title
Name of alarm output
Contact method of alarm output:
Type
Dwell time
Setup menu...
Term
NO
Normally Open
NC
Normally Closed
Duration of alarm signal
Devices
Symbol
Alarm-Out
Schedule
Meaning
No.
Number of schedule entry
Day
Day of the week
Range
Time range at 15-minute intervals
Response in defined period:
Mode
Channels
DTR-20XX
On
Continuous alarm
Event
Alarm in response to event
Off
No alarm
Enable
● alarm outputs
● internal beep by DVR
39
Setup menu, continued
Devices – Display
On the “Display” menu the mode of on-screen display is configured.
● “OSD” tab: Specify what additional information is displayed on-screen.
● “Main Monitor” tab: Specify how the camera images are displayed on the main monitor.
● “Spot Monitor” tab: Specify which cameras are displayed on the spot monitors.
Setup menu...
Term
Devices
Symbol
Display
Displayed symbol
OSD
Meaning
Status
Remote Control
Visible when remote control enabled
Zoom
Visible when Zoom mode enabled
Network
Visible when DVR operating in a network
Freeze & Sequence
● Visible when freeze frame enabled
● Visible when Sequence mode enabled
Screen Group
1/4
Free Space
Displays number of groups, and their ID
numbers
● Visible when Recycle mode enabled
● Remaining hard disk capacity, if Recycle
mode not selected
Archive
Visible when archiving in progress
Date
-
Date display
Time
-
Time display
User Name
-
Display of user name
No.
-
Display of camera number
Title
-
Display of camera title
Camera
Record
Display of Record symbols
PTZ
Visible when PTZ camera is displayed
Text-In
-
Display of character string
Transparency
-
Transparency of menu screens
-
Distance of displayed symbols from screen
margin
OSD Margin...
40
DTR-20XX
Setup menu, continued
Setup menu...
Term
Devices
Symbol
Display
Main Monitor
Meaning
Modes of sequences in multiple playback:
Mode
Full
Sequence
All cameras are switched through sequentially.
Cameo
Sequence
Only the image at the bottom right is switched
through; cameras in „Covert“ mode are not
displayed to users without „Covert“ access.
Interval
Time interval between picture refresh
Event Monitoring On
Displays image of relevant camera in full-screen mode when an
event occurs
Setup menu...
Term
Devices
Symbol
Display
Spot Monitor
Meaning
No.
Number of spot monitor output
Channels
● Cameras
● Display time of recordings from cameras on spot monitor
Devices – Remote Control
On the “Remote Control” menu the remote control function is configured.
Setup menu...
Term
Port
Devices
Symbol
Remote Control
Meaning
Interface type of remote control
Setup as specified by manufacturer:
Baud Rate
Setup…
Data Bit
Stop Bit
Parity
Remote Control Product
DTR-20XX
Remote control type as per specified list
41
Setup menu, continued
Record – Record
On the “Record” menu the basic settings for recordings and their quality are made.
Setup menu...
Term
Recycle
Record
Symbol
Record
Meaning
Enables automatic overwriting of the oldest recordings when the
hard disk is full
Note: If not enabled, recording ends when the hard disk is full.
Quality of recorded images
Resolution
Standard
CIF
High
2CIF
Event Record Dwell
Duration of recording when an event occurs
Auto Deletion
Specify time after which automatically deleted
Use Panic Recording
Enables the panic recording function
Duration of panic recording
Panic Recording Duration
No Limit
End panic recording by pressing PANIC
button
xx min.
Panic recording ends after preset time or
by pressing PANIC button
ips
Number of recorded images per second in panic recording
Quality
Picture quality of the recorded images in panic recording
42
DTR-20XX
Setup menu, continued
Record – Schedule
On the “Schedule” menu the schedule for recording is defined.
Setup menu...
Record
Term
Symbol
Schedule On
Schedule
Meaning
Enables schedule entries
Note: A recording is made only if schedule entries are enabled.
Otherwise only panic recording is possible.
No.
Number of schedule entry
Day
Day of the week
Range
Time range at 15-minute intervals
Response:
Mode
Channels
No Record
-
Time
Always record in the defined time slot in the quality
set for “Time” mode
Event
Record only in case of event in the defined time
slot in the quality set fpr „Event“ mode
Time &
Event
Always record in the defined time slot in the quality
set for “Time” mode, also in case of event in the
defined time slot in the quality set for “Event”
mode
Assignment of cameras to schedule
Picture data settings in Time and Event modes:
Settings
ips
Number of recorded images per second
Quality
Picture quality of recorded images
Picture data defaults in Time and Event modes:
Default.
DTR-20XX
ips
Number of recorded images per second
Quality
Picture quality of recorded images
43
Setup menu, continued
Record – Pre-Event
On the “Pre-Event” menu the settings for recording prior to the event are made.
Setup menu...
Term
Record
Symbol
Pre-Event
Meaning
No.
Activates the cameras
ips
Number of recorded images per second prior to the event
Quality
Picture quality of the recorded images prior to the event
Recording time prior to the event
Dwell
44
Note: The pre-event recording memory capacity is limited.
Consequently, the maximum recording time prior to the event,
the number of recorded images and picture quality are interdependent.
DTR-20XX
Setup menu, continued
Record – Archive
On the “Archive” menu the schedules and settings for archiving are entered.
Setup menu...
Record
Term
Symbol
Archive On
Archive
Meaning
Enables the archiving settings
Schedule
Day
Day of week from which to archive recordings
Range
Time range
Archive Data Range
Start of archiving, from:
From
Last Archived
Time of last archiving
xx/yy/200x
Defined date and time
End of archiving, up to:
To
Continue
No end
xx/yy/200x
Defined date and time
Enables automatic overwriting of the oldest recordings when
the archive medium is full.
Recycle
Note: If not enabled, archiving ends when the archive
medium is full.
Summary Archive
Enables the Summary Archive function
Quality of archived images in summary archive
Recording at xx images/s
Number of images per second
Picture quality of archived images
1 to 15
1
Reduced
16 to 29
1 to 2
Normal
30
2
Normal
DTR-20XX
45
Setup menu, continued
Event – Alarm-In
On the “Alarm-In” menu the alarm inputs and responses to events are configured.
Setup menu...
Term
Event
Symbol
Alarm-In
Settings
Meaning
No.
Enables the alarm inputs
Title
Name of alarm input
Contact method of alarm input:
Type
Term
Normally Open
NC
Normally Closed
Select alarm input for which the function of panic recording
should be activated
Panic Record
Setup menu...
NO
Event
Symbol
Alarm-In
Actions 1
Meaning
No.
Number of alarm input
Record
Assignment of cameras to record in event of alarm
These cameras must be in “Event” or “Time and Event” mode
within the time slot:
Setup menu > Record > Schedule
Alarm-Out
Assign and enable
● alarm outputs
● internal beep by DVR
These alarm outputs and the internal beep must be enabled
within the time slot:
Setup menu > Devices > Alarm-Out > Schedule
Assign and enable notifications:
Mail
Modem
Notify
LAN 1 to LAN 5
Alert Window
The selected function must be enabled:
Setup menu > Network > Notification
46
DTR-20XX
Setup menu, continued
Setup menu...
Term
Event
Symbol
Alarm-In
Actions 2
Meaning
No.
Number of alarm input
PTZ
Select PTZ cameras to record in event of alarm and select the
desired settings
Spot Monitor
Select spot monitor on which camera image is displayed in
event of alarm
DTR-20XX
47
Setup menu, continued
Event – Motion Detection
On the “Motion Detection” menu the motion-sensitive zones are defined and responses to events configured.
Setup menu...
Term
No.
Event
Symbol
Motion Detection
Settings
Meaning
Enables motion detection for the camera
Sensitivity of motion detection:
Sensitivity
Daytime
Nighttime
Select the motion-sensitive blocks within the time slot
Left mouse button functions:
● Click to select/deselect
● Click - hold down - drag to define a zone for selection/deletion/back
Right mouse button functions or menu in time slot to select blocks:
Zone
Min. Blocks
Select
Select complete row of blocks
Clear
Clear selection of a row
Reverse
Reverse selection of a row
Select All
Select all blocks
Clear All
Clear selection of all blocks
Reverse All
Reverse selection of all blocks
Specify in how many motion-sensitive blocks motion must be detected as
a minimum to trigger an alarm:
Daytime
Nighttime
Zone View
Mark the motion-sensitive zones (red in event of motion)
Motion Ignoring
Interval
Time interval between 2 events logged as separate events:
Daytime Setup
Definition of “Daytime” time range
48
Never
Each motion detection is logged as a separate event.
DTR-20XX
Setup menu, continued
Setup menu...
Term
Event
Symbol
Motion Detection
Actions 1
Meaning
No.
Number of alarm input
Record
Assignment of cameras to record in event of alarm
These cameras must be in “Event” or “Time and Event” mode
within the time slot:
Setup menu > Record > Schedule
Assign and enable
● alarm outputs
● internal beep by DVR
Alarm-Out
These alarm outputs and the internal beep must be enabled
within the time slot:
Setup menu > Devices > Alarm-Out > Schedule
Assign and enable notifications:
Mail
Modem
Notify
LAN 1 to LAN 5
Alert Window
The selected function must be enabled:
Setup menu > Network > Notification
Setup menu...
Term
Event
Symbol
Motion Detection
Actions 2
Meaning
No.
Number of alarm input
PTZ
Select PTZ cameras to record in event of alarm and select the
desired settings
Spot Monitor
Select spot monitor on which camera image is displayed in
event of alarm
DTR-20XX
49
Setup menu, continued
Event – Video Loss
On the “Video Loss” menu checking for covert cameras and the responses to events are configured.
Setup menu...
Term
Event
Symbol
Video Loss
Settings
Meaning
Sensitivity of check as to whether camera is covert:
Check Obscuration
Setup menu...
Term
Event
Symbol
Never
not checked
255
very sensitive
Video Loss
Actions 1
Meaning
No.
Number of covert camera
Record
Assignment of cameras to record in event of alarm
These cameras must be in “Event” or “Time and Event” mode
within the time slot:
Setup menu > Record > Schedule
Alarm-Out
Assign and enable
● alarm outputs
● internal beep by DVR
These alarm outputs and the internal beep must be enabled
within the time slot:
Setup menu > Devices > Alarm-Out > Schedule
Assign and enable notifications
Mail
Modem
Notify
LAN 1 to LAN 5
Alert Window
The selected function must be enabled:
Setup menu > Network > Notification
50
DTR-20XX
Setup menu, continued
Setup menu...
Term
Event
Symbol
Video Loss
Actions 2
Meaning
No.
Number of covert camera
PTZ
Select PTZ cameras to record in event of alarm and select the
desired settings
Spot Monitor
Select spot monitor on which camera image is displayed in
event of alarm
DTR-20XX
51
Setup menu, continued
Event – Text-In
On the “Text-In” menu the text input device is defined and the responses to text input are configured.
Setup menu...
Term
Event
Symbol
Text-In
Settings
Meaning
No.
Number of text input device
Setup
Configuration of text input >>
Title
Name of text input
Setup
Term
Port
Symbol
Meaning
Interface
Setting as specified by manufacturer of text input device (ATM,
cash-till etc.):
Setup…
Baud Rate
Data Bit
Stop Bit
Parity
Type of text input:
Text-In Product
Generic Text
Epson
Transaction Start
Character string with which text input must start for the DVR to
respond
Any Character
DVR responds to any character
Transaction End
Character string with which text input must end for the DVR to
respond
0 more line(s)
Enables recording of n more lines
Line Delimiter
Line delimiter as specified by the text input device manufacturer:
^J for LF or ^M for CR
Ignore String
Character string in the text input which the DVR is to ignore
All transmittable character strings are specified by the text input
device manufacturer.
Case Sensitive
Case sensitivity according to text input device manufacturer’s
specification
52
DTR-20XX
Setup menu, continued
Setup menu...
Term
Event
Symbol
Text-In
Actions 1
Meaning
No.
Number of alarm input
Record
Assignment of cameras to record in event of alarm
These cameras must be in “Event” or “Time and Event” mode
within the time slot:
Setup menu > Record > Schedule
Assign and enable
● alarm outputs
● internal beep by DVR
Alarm-Out
These alarm outputs and the internal beep must be enabled
within the time slot:
Setup menu > Devices > Alarm-Out > Schedule
Assign and enable notifications:
Mail
Modem
Notify
LAN 1 to LAN 5
Alert Window
The selected function must be enabled:
Setup menu > Network > Notification
Setup menu...
Term
Event
Symbol
Text-In
Actions 2
Meaning
No.
Number of alarm input
PTZ
Select PTZ cameras to record in event of alarm and select the
desired settings
Spot Monitor
Select spot monitor on which camera image is displayed in
event of alarm
DTR-20XX
53
Setup menu, continued
Event – System Event
On the “System Event” menu the self-diagnostics and corresponding messages are configured.
Setup menu...
Term
Event
Symbol
System Event
Health Check
Meaning
System
System self-diagnostics interval
Check Recording
Setup... . Configuration of schedule >>
Check Alarm-In
Interval and status for checking alarm inputs
Setup
Term
Symbol
Meaning
Schedule On
Enables schedule entries
No.
Number of schedule entry
Day
Day of the week
Range
Time range at 15-minute intervals
Interval
Checking interval
Setup menu...
Term
Event
Symbol
System Event
Storage
Meaning
Disk Bad Notify
Percentage of bad sectors on hard disk as from which an alarm
is triggered
Disk Almost Full Notify
Percentage hard disk space available as from which “Disk
Almost Full” alarm is triggered
Setup…
Configuration of data media S.M.A.R.T. check
Opens a window in which the frequency rate and time and a
temperature limit (in Celsius or Fahrenheit) for the S.M.A.R.T.
check can be specified.
If the temperature limit is exceeded an alarm is triggered.
For details of your hard disk’s temperature limit refer to the
manufacturer’s manual.
54
DTR-20XX
Setup menu, continued
Setup menu...
Term
Event
Symbol
System Event
Actions
Meaning
Events (based on checks):
Event
Alarm-Out
System
System check failed
Panic Record
Panic recording in progress
Check Recording
Recording check failed
Check Alarm-In
Check of alarm inputs failed
Disk Almost Full
Preset limit value for hard disk capacity
reached
Disk Full
Hard disk full
Disk Bad
Preset limit value for number of bad
sectors reached
Disk Temperature
Preset temperature limit reached
Disk S.M.A.R.T.
S.M.A.R.T. check failed
Assign and enable
● alarm outputs
● internal beep by DVR
Note: Not possible for system event and panic recording
Assign and enable notifications:
Mail
Notify
Modem
(not in case of system event)
LAN 1 to LAN 5
(not in case of system event)
Alert Window
(not in case of system event)
The selected function must be enabled:
Setup menu > Network > Notification
DTR-20XX
55
Setup menu, continued
Event – Event Status
The “Event Status” menu indicates the status of all possible events:
● Grey text: Event detection not enabled
● White text: Event detection enabled
● Flashing border: Message – acute event for 5 sec
● Yellow field: Pending event
Setup menu...
Event
Event Status
Event Status
Term
Event
Alarm-In
At alarm input 1 to 16
Check Alarm-In
Error detected at one of alarm inputs 1 to 16
Motion
Motion detected on camera 1 to 16
Video Loss
Video loss on camera 1 to 16
Text-In
Text input on text input device 1 to 16
Panic Record
Panic recording
Check Recording
On checking the recording
Disk Almost Full
On checking the data medium (only if DVR is not operating in Overwrite
mode)
Disk Full
On checking the data medium (only if DVR is not operating in Overwrite
mode)
Setup menu...
Event
Event Status
Term
Meaning
Type
Memory type
Disk Bad
Data carrier status
Temperature
Data carrier status
S.M.A.R.T.
Result of S.M.A.R.T. check
56
Storage
DTR-20XX
Specifications DTR-2009
Model
DTR-2009/250CD
DTR-2009/500CD
DTR-2009/750CD
EDP no.
71943
71944
71945
Video standard
PAL/NTSC (auto detection)
Remark
Recommended LCD monitors: see Accessories
Event logs
Unlimited number of entries for alarm/event/text messages, loss of signal
Security against unauthorised
use
Key locking, 64 user groups with programmable access (up to 256 users)
Transmission rate
100 images per sec (PAL)
Alarm triggering
E-mail, pager, remote SW (RAS)
Alarm activation
Automatic multi-screen display of alarm images programmable
Remote control
Wireless IR remote control (included)
Text display interface
ATM/POS, 10 channels max.
Monitor display
Real-time playback: 25 field images per sec (PAL), 30 field images per sec
(NTSC) per camera
Covert camera mode
Programmable
Time synchronisation
Network time protocol, network time server
System change log
Up to 5000 entries for login/logout, configuration changes, remote access,
change of signal connection, disk read/write errors
Zoom function
2x~4x
Playback
Frame image, 4-/9-channel split, PIP
Post-alarm recording
Up to 15 minutes
VGA
VGA playback recommended only on monitors with Multisync function
Control interface
RS-485 port for PTZ control (verified protocols: eneo-Fastrax, Pelco P/D) or
keyboard connection for remote control
Activity detection
Programmable 16 x 16 (256) grid, 5 sensitivity settings
Simplex/Duplex/Triplex/Pentaplex mode
Duplex
Video inputs
9x 1 Vp-p, (F)BAS, 75 Ohm, BNC, loop-through
Monitor outputs
4x spot outputs 1 Vp-p, (F)BAS, 75 Ohm, BNC
Video output
1x 1 Vp-p, (F)BAS, 75 Ohm, BNC; 1x S-VHS, S= 1 Vp-p, C= 0.3 Vp-p, 75
Ohm
Audio input
4x amplifier input, cinch
Audio output
1x amplifier output, cinch
Resolution
720 x 576 pixels (display)
Compression method
MPEG-4, higher compression rates with same picture quality enable maximum recording times
Recording speed
100 field images per sec at CIF resolution (336 x 272 pixels/PAL),
50 field images per sec at 2CIF resolution (672 x 272 pixels/PAL)
DTR-20XX
57
Specifications DTR-2009, continued
Model
DTR-2009/250CD
Picture size
Basic: 2/2.4 KB; Standard: 4/4.8 KB; High: 8/9.6 KB; Very high: 12/14.4 KB
(NTSC/PAL). 2 times larger in High Resolution mode
DTR-2009/500CD
Hard disk capacity
250 GB ATA hard
disk, expandable to
as many as 3 internal
hard disks
Playback speed
100 field images per sec at CIF resolution (336 x 272 pixels/PAL) and Duplex
Export of picture data
via USB 2.0, SCSI port, CD writer.
Network data export: Clip Player, AVI, JPG, BMP
Alarm inputs
9x TTL, programmable as NC/NO (terminal strip)
Alarm outputs
9x TTL, open collector (terminal strip)
Alarm reset
1x TTL (terminal strip)
Alarm messages
System error, hard disk error
500 GB ATA hard disk,
expandable to as many
as 3 internal hard disks
DTR-2009/750CD
750 GB ATA hard
disks
Pre-alarm recording
Up to 30 minutes
Recording medium
ATA-2 (EIDE) hard disks, built-in CD-RW writer
Archiving
With EIDE, SCSI and USB hard disks. Real-time mirroring
Menu languages
German, English, Italian, French, Spanish, Polish, Russian, Czech, Hungarian
Ethernet port
10Base-T, 100Base-TX, RJ-45
Remote software
For remote administration and image search function (RAS plus included)
Ports
3x USB, 1x RS-485, 1x RS-232 (remote control/configuration or modem), 1x
SCSI for memory expansion
Power Supply
100 VAC~230VAC, 50/60Hz
Power consumption
approx. 150 W
Temperature range
5°C to 40°C
Housing
Metal with plastic front panel
Colour
Pantone 427C
Dimensions (H x W x D)
88 x 430 x 405 mm
Weight
approx. 10.2 kg
58
DTR-20XX
Specifications DTR-2016
Model
DTR-2016/250CD
DTR-2016/500CD
DTR-2016/750CD
EDP No.
71946
71947
71948
Video standard
PAL/NTSC (auto detection)
Remark
Recommended LCD monitors: see Accessories
Event logs
Unlimited number of entries for alarm/event/text messages, loss of signal
Security against unauthorised
use
Key locking, 64 user groups with programmable access (up to 256 users)
Transmission rate
100 images per sec (PAL)
Alarm triggering
E-mail, pager, remote SW (RAS)
Alarm activation
Automatic multi-screen display of alarm images programmable
Remote control
Wireless IR remote control (included)
Text display interface
ATM/POS, 10 channels max.
Monitor display
Real-time playback: 25 field images per sec (PAL), 30 field images per sec
(NTSC) per camera
Covert camera mode
Programmable
Time synchronisation
Network time protocol, network time server
System change log
Up to 5000 entries for login/logout, configuration changes, remote access,
change of signal connection, disk read/write errors
Zoom function
2x~4x
Playback
Frame image, 4-/9-/16-channel split, PIP
Post-alarm recording
Up to 15 minutes
VGA
VGA playback recommended only on monitors with Multisync function
Control interface
RS-485 port for PTZ control (verified protocols: eneo-Fastrax, Pelco P/D) or
keyboard connection for remote control
Activity detection
Programmable 16 x 16 (256) grid, 5 sensitivity settings
Simplex/Duplex/Triplex/Pentaplex mode
Duplex
Video inputs
16x 1 Vp-p, (F)BAS, 75 Ohm, BNC, loop-through
Monitor outputs
4x spot outputs 1 Vp-p, (F)BAS, 75 Ohm, BNC
Video output
1x 1 Vp-p, (F)BAS, 75 Ohm, BNC; 1x S-VHS, S= 1 Vp-p, C= 0.3 Vp-p, 75
Ohm
Audio input
4x amplifier input, cinch
Audio output
1x amplifier output, cinch
Resolution
720 x 576 pixels (display)
Compression method
MPEG-4, higher compression rates with same picture quality enable maximum recording times
Recording speed
100 field image per sec at CIF resolution (336 x 272 pixels/PAL),
50 field image per sec at 2CIF resolution (672 x 272 pixels/PAL)
DTR-20XX
59
Specifications DTR-2016, continued
Model
DTR-2016/250CD
Picture size
Basic: 2/2.4 KB; Standard: 4/4.8 KB; High: 8/9.6 KB; Very high: 12/14.4 KB
(NTSC/PAL). 2 times larger in High Resolution mode
DTR-2016/500CD
Hard disk capacity
250 GB ATA hard
disk, expandable to
as many as 3 internal
hard disks
Playback speed
100 field image per sec at CIF resolution (336 x 272 pixels/PAL) and Duplex
Export of picture data
via USB 2.0, SCSI port, CD writer.
Network data export: Clip Player, AVI, JPG, BMP
Alarm inputs
16x TTL, programmable as NC/NO (terminal strip)
Alarm outputs
16x TTL, open collector (terminal strip)
Alarm reset
2~4 TTL (terminal strip)
Alarm messages
System error, hard disk error
500 GB ATA hard disk,
expandable to as many
as 3 internal hard disks
DTR-2016/750CD
750 GB ATA hard
disks
Pre-alarm recording
Up to 30 minutes
Recording medium
ATA-2 (EIDE) hard disks, built-in CD-RW writer
Archiving
With EIDE, SCSI and USB hard disks. Real-time mirroring
Menu languages
German, English, Italian, French, Spanish, Polish, Russian, Czech, Hungarian
Ethernet port
10Base-T, 100Base-TX, RJ-45
Remote software
For remote administration and image search function (RAS plus included)
Ports
3x USB, 1x RS-485, 1x RS-232 (remote control/configuration or modem), 1x
SCSI for memory expansion
Power Supply
100 VAC~230VAC, 50/60Hz
Power consumption
approx. 150 W
Temperature range
5°C to 40°C
Housing
Metal with plastic front panel
Colour
Pantone 427C
Dimensions (H x W x D)
88 x 430 x 405 mm
Weight
approx. 10.2 kg
60
DTR-20XX
Accessories
EDP No.
Short description
71857
250GB hard disk for DLR/DXR/DTR and DCR
71919
500GB hard disk for DLR/DXR/DTR and DCR
74088
System keyboard with 3-axis joystick
74092
System keyboard with joystick, 5” monitor
71902
USB mouse for DVR series DXR, DLR3
90392
15” LCD industrial colour monitor, 1024x768
90393
17” LCD industrial colour monitor, 1280x1024
90430
19” LCD industrial colour monitor, 1280x1024
90443
17” LCD colour monitor, 1280x1024 pixels
90467
32” prof. 16:9 TFT colour monitor, 4x FBAS
90476
23” prof. 16:9 LCD colour monitor, 4x FBAS
DTR-20XX
61
Supported PTZ cameras
Manufacturer
Designation
Manufacturer
Designation
Costar
CDC 2500
Ademco Video
Orbiter Microsphere
Dyna Color
CDC2400
SysMania
ORX_1000
Chilsung
CRD-J6416
Linlin
PIH-717
Fine
CRR-1660s
ELMO
PTC-200C/CVAS
Pelco
D-protocol
ELMO
PTC-250C
Dennard
Dennard2060
Pacom
Pacom 2036
Tokina
DMP-1223
Dongyang
Power Controller
Dongyang Unitech
DRX-500
Sungjin
Receiver/MPU
Dongyang
DY-255RXC
Costar
SIC722V
Sensormatic
Delta Dome II/Ultra IV
Samsung Techwin
SPD 1600
Eneo
Fastrax
Samsung
Samsung Dome
Philips
G3 Basic AutoDome
Pelco
Spectra Dome
LG Honeywell)
GRU604A
Samsung Techwin
SRX-100B
JVC
TK-S576
Hitron
Speed Dome
Sensormatic
Ultra VI
Canon
VC-C4
Canon
VC-C50i
Inter-M
VRX-2201
Vicon
Vicon
Hitron
22x AF Zoom
360Vision
VisionDome
Panasonic
WJ-SX550A
Panasonic
WV-CS850/854
CBC
ZC-SD622J
Samsung
Zoom Camera
Honeywell
HDC-655
LG Honeywell
HSD-25X
Honeywell
HSDN-251
Idis
IRX-100
Ultrak
KD6
Ultrak
KD6 Z-series
Kalatel
KTD-312
LG
LPT-A100L
Novus-C
Samsung
62
MRX-1000
DTR-20XX
Index
A
Accessories 61
Alarm
Configuring inputs 46
Configuring outputs 39
Connecting inputs 8
Connecting outputs 8
Motion detection 49
Resetting 9
Setting schedule for outputs 39
Setting signal duration 39
Ambient conditions 3, 58
Archiving
Configuring 45
Memory requirement 20, 45
Setting schedule 45
Assigning cameras
Alarm-In 46
Motion detection 48, 49
Text-In 53
Video loss 50
Assigning PTZ cameras
Alarm-In 47
Motion detection 48, 49
Text-In 53
Video loss 51
B
Basic functions 7
C
Calendar search 22
Cameo 41
Cleaning 3
Clip-Copy 26
Configuring a pre-event 44
Configuring audio outputs 38
Configuring cameras 37
Configuring event responses 46
Configuring motion detection 48
Configuring notification 36
Configuring panic recording 42
Configuring PTZ cameras 37
Configuring remote control 41
Configuring text input as event 52
Configuring video loss as event 50
Connecting cameras 8
Connections 8
DTR-20XX
Control options 7
Control protocols 62
Controls
Front panel controls 9
Remote control 11
Copying recordings 26
Covert camera setup 19, 37
Covert mode 19, 37
D
Date setting 29
Defining motion-sensitive zones 48
Display
Configuring 40
Hiding 19, 37
Displaying event status 56
Display menu
Access 14
Disposal 66
DVRNS
Network configuratio 35
Dwell time 39
E
E-mail notification 36
EMC class 3
Enabling notification
Alarm-In 46
Motion detection 49
System event 55
Text-In 53
Video loss 50
Event
Configuring a pre-event 44
Configuring responses 46
Defining motion-sensitive zones 48
Displaying status 56
Setting recording time 42
System events 54
Text input 52
Video loss 50
Event log 23
F
Front panel controls 9
Controls 9, 10
63
Index, continued
G
R
Getting started
Video recorder 3, 16
Recordings
Copying 26
Deleting 18
Memory requirement 20
Searching 21
Setting schedule 43
Recycling the device 66
Remote control
Controls 11
Setting system ID 16, 28
Reset 8, 19
Restoring factory defaults 19
H
Health check 54
I
IP address 34, 35
L
LAN
Network configuration 34
M
Memory requirement
Archiving 20, 45
Recordings 20
Memory type 30
Menu descriptions
Search menu 21
Setup menu 27
Menu structure 12
Modem
Network configuration 34
Monitor
Configuring display 40
Configuring display sequence 41
Connecting 8
Motion search 25
N
Network configuration 33
Network settings
DVRNS 35
LAN 34
Modem 34
P
Package contents 7
PANIC 9, 42
PTZ-menu
Access 14
PTZ cameras
Connecting 8
Supported cameras 62
64
S
Safety instructions 3
Schedule
Setting for alarm 39
Setting for archiving 45
Setting for recording 43
Search
Calendar search 22
Event log 23
Motion search 25
Text-In 24
Search-menu
Access 15
Setting a password 32
Setting automatic overwrite 42
Setting group access privileges 32
Setting menu language 28
Setting recording quality 42
Setting recording time when events occur 42
Setting system ID for remote control 28
Setting up user groups 32
Setting up users 32
Setup menu
Access 15
Menu descriptions 27
Shutdown 17
Software updates 19
Software version 28
Specifications 57
Specifying public holidays
29
Spot monitor
Assigning camera 41
Connecting 8
DTR-20XX
Index, continued
Storage media
Displaying status 30
Displaying usage 30
Setting automatic overwrite 42
Switching off 17
Switching on 17
System
Exporting configuration 28
Importing configuration 28
Log out USER 33
Shutdown 33
System events
Configuring 54
Health check 54
T
Text-in search 24
Time
Setting 29
Synchronising 29
DTR-20XX
65
Notes on disposal
Correct disposal of this DVR
WEEE (Waste Electrical & Electronic Equipment)
Applicable in the member states of the European Union and other European countries with a separate collection system
The marking on the DVR and on the documentation stipulates that it must not be
thrown away in normal domestic waste at the end of its useful life.
General rules
► Avoid uncontrolled waste disposal: Please dispose of this DVR separately from other waste, so as to avoid
posing a hazard to the environment and to human health.
► Recycle the DVR in order to aid the sustainable reuse of material resources.
Private users
► Contact the retailer from whom you purchased the DVR or your competent local authority to find out how
you can recycle the DVR in an environmentally friendly way.
Commercial users
► This DVR must not be thrown away with trade waste. To clarify the conditions of disposal, check your
purchase contract or contact your supplier.
66
DTR-20XX
eneo® is a registered trademark of Videor Technical E. Hartig GmbH
Exclusive distribution through specialised trade channels only.
VIDEOR TECHNICAL E. Hartig GmbH
Carl-Zeiss-Str. 8 · 63322 Rödermark, Germany
Tel. +49 (0) 6074 / 888-0 · Fax +49 (0) 6074 / 888-100
www.videortechnical.com
Operating Instructions version 08/2007 (V1.6)
Subject to technical change without notice.
© Copyright by VIDEOR TECHNICAL 2007
">