PRID_1761_doc_170510.pdf
PD-1s
mk3
Pro-Drive Direct Drive Turntable
Ref. No: 170.510
Safety Warnings:
The unit should not be opened or repaired by anyone except properly
qualified service personnel.
Double insulated - when servicing, use only identical replacement parts.
All the safety and operating instructions should be read before the
appliance is operated.
To prevent fire or shock hazard, do not expose this appliance to rain
or moisture.
To reduce the risk of electric shock, do not remove the cover (or back).
There are no serviceable parts inside. Always refer servicing to qualified
service personnel.
Check List
•Check that the following parts are included in the package with the
main unit:
1) Turntable platter
Cautionary Notes:
2) Slip mat
Care must be taken not to damage the power supply cord housing,
which could expose line parts and cause electric shock. When removing
from wall outlet, be sure to remove by holding the plug and not by
pulling the cord.
In order to prevent electric shock; do not open the top cover. If a
problem occurs, contact your dealer.
Do not place metal objects or spill liquid inside the mixer. Electric shock
or malfunction may result.
Any use of the controls, or any adjustment, or the performance of
any procedure other than those specified herein may result in serious
damage to your health.
3) Dust cover
4) 45-rpm adapter
5) Counterweight
6) Headshell
7) Operating instructions
8) Phono lead
Illustration and Main Features
1) 45-rpm Adapter
2) Slip Mat
3) Center Spindle
4) Strobe Dots
5) Power Switch/Strobe
6) Start/Stop Button
8) Target Light
9) Remote Start Socket: This jack can be connected with an external
switch to perform the Start/Stop operation.
10)Headshell
11) Speed Select Buttons
12)Quartz lock LED
13)Pitch Control Slider
14)Static Balanced Tonearm
15)Trim control
16)Arm Rest
17)Cueing Lever
18)Anti-skating Knob
19)Counterweight
20)Spare Cartridge Holder
21)Hinge For Dust Cover
22)Phono Sockets L+R
23)Phono Sockets Earth (GND)
Assembly Instructions
Scratch Mixing Tip
1. Remove the main unit with the packing from the box and take off
the packing.
If you are using the deck for scratching the cartridge can be adjusted
to give better traction as follows:
Align the cartridge in a direct line to the back of the tone arm.
2. Insert the 45-rpm adaptor in the slot on the turntable.
3. Place the turntable platter onto the center spindle.
4. Place the slip mat on the platter.
5.
Installation of cartridge:
When installing a cartridge, refer to the operating instructions of
that cartridge.
During installation, attach the stylus protector to guard the stylus
tip from damage.
NOTE: this is not advisable to use during normal play.
6. Insert the headshell into the front end of the tonearm, then turn
the lock nut clockwise with the headshell firmly held horizontally.
Operation
The following instructions assume that the counter balance weight has
been set.
7. Slide counterweight onto tonearm.
Twist it lightly and it will screw onto the rear shaft of the tonearm.
1. Rotate the power switch to turn on the power, the speed indicator
and the strobe-illuminator will light up.
8. Adjustment of horizontal zero (0) balance and stylus pressure:
(a) Remove the stylus protector, do not touch the stylus tip
during the adjustment.
(b) Set the cueing lever to the lower position.
(c) Release the arm clamp and lift the tonearm from the arm
rest to free it.
(d) While holding the Headshell lever rotate the counterweight
until the tonearm is approximately balanced horizontally
(floats freely).
(e) Refasten the tonearm with the arm clamp.
(f)Hold the counterweight stationary with one hand and rotate
only the stylus-pressure ring to bring the number “0” of the
ing into alignment with the center line on the tonearm rear
shaft.
(g) otate the counterweight clockwise until the scale shows the
value corresponding to the pressure of the used stylus,
typically 4 grams.
9. Set the anti-skating control knob to the same value as the stylus
pressure.
10. Install the dust cover to the main unit.
2.Place a record on the slip mat, when playing a 45rpm record with a
large center hole; place the 45-rpm adaptor on the center spindle.
3. Set the speed to match the record.
4. Remove the stylus protector, release the arm clamp.
5. Set the cueing lever to the up position.
6. Press the Start/Stop button, the turntable platter will start to
rotate.
7. Move the tonearm over the desired groove.
8. Set the cueing lever to the down position, the tonearm will
descend slowly onto the record and play begins.
9. When play is finished, raise the cueing lever, move the tonearm to
the arm rest, secure the tonearm with the arm clamp.
10. Press the Start/Stop button to stop the platter rotating, push the
power button to turn off the power.
Suspend play
Set the cueing lever to “UP” position during play, the stylus tip of
the cartridge will be lifted from the record.
Target light
This unit is provided with a target light for illuminating the stylus
tip during play. Push the target light button, the target light will
be raised into position for illuminating the stylus tip.
Placement
•Do not place the unit in a location where it will be exposed to direct
sunlight or near a heating appliance.
•Do not place the unit in a location where there is high humidity or
a lot of dust.
• Cartridge may pick up sound pressures or vibrations from the
speakers coming along the floor or through the air resulting in
howling. Find a location, which is very stable, and vibration free.
Remote Start
The remote start jack socket is located at the rear of the deck. When
a jack plug is inserted and connected to a compatible mixer. The deck
will be able to be started automatically from the mixer remote start
control.
• The legs have functions for adjusting the height of the unit itself.
Adjust the legs to stabilize the main body horizontally.
Connections
1. Connect the power cord to the household AC outlet.
Changing the Speed
2.
As long as the pitch control (13) is in center click position, the turntable
is operated with quartz- controlled speed.
The Blue LED (12) will then be lit.
The speed can be increased or decreased by 10% via the pitch control
(13). The Blue LED (12) will then be off.
The Trim control (15) can be used to provide an increased range of pitch
control adjustment in order to have the turntable rotate extremely slow
or fast.
For DJ Mixer operation, the start/stop function can be remotely
controlled by a separate switch. Use the jack remote socket (9) to
connect this to the mixer option.
Connect the unit output terminals to the PHONO inputs of your
mixer.
Output terminals Mixer input
L White)
>>
L Channel
R (Red)
>>
R Channel
GND (Spade)
>>
GND
NOTE: Be sure to connect the separate ground terminal firmly to the
Mixer. If this connection is not made or is loose, a power source “HUM”
will result.
Maintenance
CE Markings
• Clean the stylus periodically with a soft brush to prevent the
accumulation of dust.
EMC Conformity
The PD-1s Professional Direct Drive Turntable, have been tested to
demonstrate compliance with the EMC 89/336/EEC directive, under
which the following harmonised standards apply:
I)
EN55020
Electromagnetic Immunity
iv) EN55013
Electromagnetic Compatibility
• When the sound becomes distorted or noisy, check the stylus. If
worn out, replace it with a new one.
• From time to time, the dust cover and turntable cabinet should be
wiped with a soft, dry cloth.
Electrical
Equipment Safety Regulations (1994)
The PD-1 Professional Direct Drive Turntable, have been designed and
tested to demonstrate compliance the LVD 73/23/Eec directive, using
the following standard.
I) EN60065 Safety requirements for mains operated electronic
equipment for household and similar general use.
Installing a Cartridge
To install a cartridge into the headshell provided, refer to the
installation instructions supplied by the manufacturer of that cartridge.
During installation, attach the stylus protector to guard the stylus tip
from damage.
Attach wires as follows:
White (L+)
Blue (L-)
Red (R+)
Green (R-)
Left Channel +
Left Channel –
Right Channel +
Right Channel –
Technical Specification
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 pole 2 phase brushless DC
Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Direct Drive
Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +/- 10%
Starting Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . More than 1kgf.cm
Braking system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronic brake
Braking Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Less than 1 sec.
Starting Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Less than 1 sec.
Braking Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Less than 1 sec.
Tracking force adjustment range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 – 4g
Effective arm length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230.5mm
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 115 - 230V, 50/60Hz
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Watts
Dimension (WxDxH) . . . . . . . . . . . . . . . . . . . . . . . . . 450 x 350 x 146 mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.6 Kgs
For other products in the Citronic range, visit . . .
www.citronic.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising