MANUAL_CMP-WNROUT50_55_60_FULL_MANUAL_ENG.PDF

MANUAL_CMP-WNROUT50_55_60_FULL_MANUAL_ENG.PDF
CMP-WNROUT50
CMP-WNROUT55
CMP-WNROUT60
MANUAL
ANLEITUNG
MODE D’EMPLOI
GEBRUIKSAANWIJZING
MANUALE
MANUAL DE USO
1.) HARDWARE CONFIGURATION
HASZNÁLATI
ÚTMUTATÓ
*The CMP-WNROUT50
has
only one antenna
BRUKSANVISNING
KÄYTTÖOHJE
NÁVOD K POUŽITÍ
Antenna
Power Jack
Auto MDI/MDIX RJ-45 Ports
Automatically sense the types of WAN
and LAN when connecting to Ethernet
3 in1 Button
1.WPS
2.Wireless
ON
3.Reset
Status
LED
WAN
LED
Wi-Fi
LED
LAN1~LAN4
LEDs
2
2.) LED INDICATORS
LED status
Description
Status
Green in flash
Device status is working.
WAN LED
Green
RJ45 cable is plugged
Green in flash
Data access
Green
RJ45 cable is plugged
Green in flash
Data access
Green
WLAN is on
Green in flash
Data access
Green in fast flash
Device is in WPS PBC mode
Green in dark
Wi-Fi Radio is disabled
LAN LED
WiFi LED
3.) BUTTON DEFINITION
Description
WPS
When Wireless is On, press this button (about 1 sec) to execute
WPS function.
Wireless On
When Wireless is off depend as Schedule Rule, Press this
button(about 1 sec) to enable "Wireless Radio".
Reset
1. Press this button then Power on the device
2. Press about 3~4 second, the device will reset to default then
Status LED flashes per sec in Normal status.
Notice: If Status LED flashes very fast, it means to press this button
too long and please try again.
4.) HOW TO OPERATE
Step 1 Insert the Ethernet cable into LAN
Port:
Insert the Ethernet patch cable into LAN port
on the back panel of Router, and an available
Ethernet port on the network adapter in the
computer you will use to configure the unit.
3
Step 2 Insert the Ethernet patch cable into
Wired WAN port:
Insert the Ethernet patch cable form DSL
Modem into Wired WAN port on the back
panel of Router.
Step 3. Power on Router:
Connect the power adapter to the receptor on
the back panel of your Router.
Step 4. Complete the setup.
Connect the power adapter to the receptor on
the back panel of your Router.
5.) GETTING STARTED
5.1.Select Language then click “Next” to
continue
4
5.2 Setup mode
You can select Wizard mode to run the
setup step-by-step or run advanced mode to
diagnose the network settings of the router.
5.3 Advanced mode Setup.
Check the PC, Router or Internet icons for
the Status of PC, Router or Internet.
5.4 Quick Wizard Install mode Setup
1. Make sure the router is powered on.
2. Make sure your network adapter is
connected to the LAN port of the router
3. Make sure your network adapter has an
IP address. Click “Next” to continue
5
5.5. Wireless Setting.
Key in the SSID, Channel and Security
options, and then click “Next” to continue.
5.6 Auto Detect WAN Service.
Click “Next” for continue.
Click the button, “Let me select WAN service
by myself”, to disable this function.
Note: The Item supports to detect the
Dynamic and PPPoE WAN Services only
Example, the Dynamic WAN type is
detected.
6
5.7. Manual select WAN Service
In the manual mode, Click the any icons to
continue
5.8 Summary of the settings and Next to
“Reboot”
Click “Next” to continue.
5.9 Apply the Settings or Modify.
Click “Next” to continue.
7
5.10 Test the Internet connection.
Test WAN Networking service. Click “Next”
to continue.
You can ignore the by select the “Ignore
Test”.
5.11 Setup Completed.
The EzSetup is finish, you can open the
default web browser to configure advanced
settings of the Router.
Click “Finish” to complete the installation.
8
6.) WIZARD CONFIGURATION
Type in the IP Address
(http://192.168.123.254)
Type password, the default is
“admin” and click ‘login’ button.
Press “Wizard” for basic
settings with simple way.
Press “Next” to start wizard.
9
Step 1:
Set up your system password.
Step 2:
Select Wan Type.
Auto Detecting or
Setup Manually.
10
Step 3:
Setup the LAN IP and WAN
Type.
Example:
Step 4:
Please fill in PPPoE service
information which is provided
by your ISP.
Step 5:
Set up your Wireless.
11
Set up your Authentication and
Encryption.
Step 6:
Then click Apply Setting.
And then the device will reboot.
Step 7:
Click Finish to complete it.
12
7.) SYSTEM STATUS
This option provides the for observing the product’s working status:
WAN status.
If the WAN port assigned to a dynamic IP, there may appear a “Renew” or “Release” button on the sidenote
column. You can click this button to renew or release IP manually.
Statistics of WAN: enables you to monitor inbound and outbound packets.
13
8.) EXTRA SETTINGS
8.1.) Basic settings
Please Select “Advanced Setup” to Setup
14
Press “Change”
This option is primary to enable this product to work properly. The setting items and the web appearance depend on the WAN type.
Choose correct WAN type before you start.
1.
LAN IP Address: the local IP address of this device. The computers on your network must use the LAN IP address of your product
as their Default Gateway. You can change it if necessary.
2.
WAN Type: WAN connection type of your ISP. You can click Change button to choose a correct one from the following four
options:
A.
Static IP Address: ISP assigns you a static IP address.
B.
Dynamic IP Address: Obtain an IP address from ISP automatically.
C.
PPP over Ethernet: Some ISPs require the use of PPPoE to connect to their services.
D. PPTP: Some ISPs require the use of PPTP to connect to their services.
F. L2TP: Some ISPs require the use of L2TP to connect to their services
Static IP Address: ISP assigns you a static IP address:
WAN IP Address, Subnet Mask, Gateway, Primary and Secondary DNS: enter the proper setting provided by
your ISP.
15
Dynamic IP Address: Obtain an IP address from ISP automatically.
Host Name: optional. Required by some ISPs, for example, @Home.
Renew IP Forever: this feature enables this product to renew your IP address automatically when the lease
time is expiring-- even when the system is idle.
PPP over Ethernet: Some ISPs require the use of PPPoE to connect to their services.
PPPoE Account and Password: the account and password your ISP assigned to you. For security,
this field appears blank. If you don't want to change the password, leave it empty.
PPPoE Service Name: optional. Input the service name if your ISP requires it. Otherwise, leave
it blank.
Maximum Idle Time: the amount of time of inactivity before disconnecting your PPPoE session.
Set it to zero or enable Auto-reconnect to disable this feature.
Maximum Transmission Unit (MTU): Most ISP offers MTU value to users. The most common MTU value
is 1492.
Connection Control: There are 3 modes to select:
16
Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.
Auto-Reconnect(Always-on):The device will link with ISP until the connection is established.
Manually :The device will not make the link until someone clicks the connect-button in the Staus-page.
PPTP: Some ISPs require the use of PPTP to connect to their services
First, Please check your ISP assigned and Select Static IP Address or Dynamic IP Address.
1. My IP Address and My Subnet Mask: the private IP address and subnet mask your ISP assigned to you.
2. Server IP Address: the IP address of the PPTP server.
3. PPTP Account and Password: the account and password your ISP assigned to you. If you don't
want to change the password, keep it empty.
3. Connection ID: optional. Input the connection ID if your ISP requires it.
4. Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to zero or
enable Auto-reconnect to disable this feature. If Auto-reconnect is enabled, this product will
connect to ISP automatically, after system is restarted or connection is dropped.
Connection Control: There are 3 modes to select:
Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.
Auto-Reconnect(Always-on):The device will link with ISP until the connection is established.
Manually: The device will not make the link until someone clicks the connect-button in the Staus-page.
17
L2TP: Some ISPs require the use of L2TP to connect to their services
First, Please check your ISP assigned and Select Static IP Address or Dynamic IP Address.
For example: Use Static
1. My IP Address and My Subnet Mask: the private IP address and subnet mask your ISP assigned
to you.
2. Server IP Address: the IP address of the PPTP server.
3. PPTP Account and Password: the account and password your ISP assigned to you. If you don't
want to change the password, keep it empty.
3. Connection ID: optional. Input the connection ID if your ISP requires it.
4. Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to zero or
enable Auto-reconnect to disable this feature. If Auto-reconnect is enabled, this product will
connect to ISP automatically, after system is restarted or connection is dropped.
Connection Control: There are 3 modes to select:
Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.
Auto-Reconnect(Always-on):The device will link with ISP until the connection is established.
18
Manually :The device will not make the link until someone clicks the connect-button in the Staus-page.
19
Virtual Computers(Only for Static and dynamic IP address Wan type)
Virtual Computer enables you to use the original NAT feature, and allows you to setup the one-to-one
mapping of multiple global IP address and local IP address.
•
•
•
Global IP: Enter the global IP address assigned by your ISP.
Local IP: Enter the local IP address of your LAN PC corresponding to the global IP address.
Enable: Check this item to enable the Virtual Computer feature.
20
3.3.1.2 DHCP Server
Press “More>>”
1.
DHCP Server: Choose “Disable” or “Enable.”
2.
Lease time: This is the length of time that the client may use the IP address it has been
Assigned by dhcp server.
3.
IP pool starting Address/ IP pool starting Address: Whenever there is a request, the DHCP
server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must
specify the starting and ending address of the IP address pool.
4.
Domain Name: Optional, this information will be passed to the client.
5.
Primary DNS/Secondary DNS: This feature allows you to assign DNS Servers
6.
Primary WINS/Secondary WINS: This feature allows you to assign WINS Servers
7.
Gateway: The Gateway Address would be the IP address of an alternate Gateway.
This function enables you to assign another gateway to your PC, when DHCP server offers an IP to your PC.
8.
DHCP Client List:
21
3.3.1.3 Wireless Setting
Wireless settings allow you to set the wireless configuration items.
Wireless Radio: The user can turn on or off Wireless Service.
Wireless Off Schedule: Before turning Off Wireless Radio, the device will detect if Wireless station is online,
then depend as Schedule ” 01:00~08:30” to disable WiFi service.
Network ID (SSID): Network ID is used for identifying the Wireless LAN (WLAN). Client stations can roam
freely over this product and other Access Points that have the same Network ID. (The factory setting is
“default”)
SSID Broadcast: The router will Broadcast beacons that have some information, including ssid so that
The wireless clients can know how many ap devices by scanning function in the network. Therefore,
This function is disabled, the wireless clients can not find the device from beacons.
Channel: The radio channel number. The permissible channels depend on the Regulatory Domain.
WPS (WiFi Protection Setup)
WPS is WiFi Protection Setup which is similar to WCN-NET and offers safe and
easy way in Wireless Connection.
22
WDS(Wireless Distribution System)
WDS operation as defined by the IEEE802.11 standard has been made available. Using WDS it is possible
to wirelessly connect Access Points, and in doing so extend a wired infrastructure to locations where cabling
is not possible or inefficient to implement.
Security: Select the data privacy algorithm you want. Enabling the security can protect your data while it is
transferred from one station to another.
23
There are several security types to use:
WEP :
When you enable the 128 or 64 bit WEP key security, please select one WEP key to be used and input 26 or
10 hexadecimal (0, 1, 2…8, 9, A, B…F) digits.
802.1X
Check Box was used to switch the function of the 802.1X. When the 802.1X function is enabled, the Wireless
user must authenticate to this router first to use the Network service.
RADIUS Server
IP address or the 802.1X server’s domain-name.
RADIUS Shared Key
Key value shared by the RADIUS server and this router. This key value is consistent with the key value in the
RADIUS server.
WP
A-PSK
1. Select Encryption and Pre-share Key Mode
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If ASCII, the length of pre-share key is from 8 to 63.
2. Fill in the key, Ex 12345678
24
WPA
Check Box was used to switch the function of the WPA. When the WPA function is enabled, the Wireless
user must authenticate to this router first to use the Network service. RADIUS Server IP address or the
802.1X server’s domain-name.
Select Encryption and RADIUS Shared Key
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If ASCII, the length of pre-share key is from 8 to 63.
Key value shared by the RADIUS server and this router. This key value is consistent with the key value in the
RADIUS server.
WPA2-PSK(AES)
1. Select Pre-share Key Mode
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If ASCII, the length of Pre-share key is from 8 to 63.
2. Fill in the key, Ex 12345678
WPA2(AES)
Check Box was used to switch the function of the WPA. When the WPA function is enabled, the Wireless
user must authenticate to this router first to use the Network service. RADIUS Server
IP address or the 802.1X server’s domain-name.
Select RADIUS Shared Key
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If ASCII, the length of Pre-share key is from 8 to 63.
Key value shared by the RADIUS server and this router. This key value is consistent with the key value in the
RADIUS server.
WPA-PSK /WPA2-PSK
25
The router will detect automatically which Security type the client
uses to encrypt.
1. Select Pre-share Key Mode
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If ASCII, the length of Pre-share key is from 8 to 63.
2. Fill in the key, Ex 12345678
WPA/WPA2
Check Box was used to switch the function of the WPA. When the WPA function is enabled, the Wireless
user must authenticate to this router first to use the Network service. RADIUS Server
The router will detect automatically which Security type(Wpa-psk version 1 or 2) the client
uses to encrypt.
IP address or the 802.1X server’s domain-name.
Select RADIUS Shared Key
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If ASCII, the length of Pre-share key is from 8 to 63.
Key value shared by the RADIUS server and this router. This key value is consistent with the key value in the
RADIUS server.
Wireless Client List
26
3.3.1.4 Change Password
You can change Password here. We strongly recommend you to change the system password for security
reason.
8.2) Forwarding rules
27
3.3.2.1 Virtual Server
This product’s NAT firewall filters out unrecognized packets to protect your Intranet, so all hosts behind this product are invisible to
the outside world. If you wish, you can make some of them accessible by enabling the Virtual Server Mapping.
A virtual server is defined as a Service Port, and all requests to this port will be redirected to the computer
specified by the Server IP. Virtual Server can work with Scheduling Rules, and give user more flexibility
on Access control. For Detail, please refer to Scheduling Rule.
3.3.2.2 Special AP
Some applications require multiple connections, like Internet games, Video conferencing, Internet telephony, etc. Because of the
firewall function, these applications cannot work with a pure NAT router. The Special Applications feature allows some of these
applications to work with this product. If the mechanism of Special Applications fails to make an application work, try setting your
computer as the DMZ host instead.
28
1.
2.
Trigger: the outbound port number issued by the application..
Incoming Ports: when the trigger packet is detected, the inbound packets sent to the specified port numbers are allowed to pass
through the firewall.
This product provides some predefined settings Select your application and click Copy to to add the predefined setting to your list.
Note! At any given time, only one PC can use each Special Application tunnel.
3.3.2.3 Miscellaneous Items
IP Address of DMZ Host
DMZ ( DeMilitarized Zone) Host is a host without the protection of firewall. It allows a computer to be
exposed to unrestricted 2-way communication for Internet games, Video conferencing, Internet telephony
and other special applications.
NOTE: This feature should be used only when needed.
Super DMZ(IP Passthrough)
The client be set in Super DMZ and dhcp server assigns a global IP which is the same with Wan IP of this
device. This client also can access the local client.This client behind NAT can use various applications
without limitation.
Hardware DMZ Port
This feature can let the device to get Global IP from ISP directly. Some Devices, like STB or MOD, should
work via assigned Port.
Non-standard FTP port
You have to configure this item if you want to access an FTP server whose port number is not 21. This
setting will be lost after rebooting.
Xbox Support
The Xbox is a video game console produced by Microsoft Corporation. Please enable this function when you
play games.
UpnP Setting
The device also supports this function.If the OS supports this function enable it,like Windows Xp.When the
user get ip from Device and will see icon as below:
29
8.3.) SECURITY SETTINGS
30
3.3.3.1 Packet Filters
Packet Filter enables you to control what packets are allowed to pass the router. Outbound filter applies on
all outbound packets. However, Inbound filter applies on packets that destined to Virtual Servers or DMZ
host only. You can select one of the two filtering policies:
1. Allow all to pass except those match the specified rules
2. Deny all to pass except those match the specified rules
You can specify 8 rules for each direction: inbound or outbound. For each rule, you can define the following:
•
•
•
•
•
•
Source IP address
Source port address
Destination IP address
Destination port address
Protocol: TCP or UDP or both.
Use Rule#
For source or destination IP address, you can define a single IP address (4.3.2.1) or a range of IP addresses
(4.3.2.1-4.3.2.254). An empty implies all IP addresses.
For source or destination port, you can define a single port (80) or a range of ports (1000-1999). Add prefix
"T" or "U" to specify TCP or UDP protocol. For example, T80, U53, U2000-2999. No prefix indicates both
TCP and UDP are defined. An empty implies all port addresses. Packet Filter can work with Scheduling
Rules, and give user more flexibility on Access control. For Detail, please refer to Scheduling Rule.
Each rule can be enabled or disabled individually.
Inbound Filter:
To enable Inbound Packet Filter click the check box next to Enable in the Inbound Packet Filter field.
Suppose you have SMTP Server (25), POP Server (110), Web Server (80), FTP Server (21), and News
Server (119) defined in Virtual Server or DMZ Host.
Example 1:
31
(1.2.3.100-1.2.3.149) Remote hosts are allow to send mail (port 25), and browse the Internet (port 80)
(1.2.3.10-1.2.3.20) Remote hosts can do everything (block nothing)
Others are all blocked.
Example 2:
32
(1.2.3.100-1.2.3.119) Remote hosts can do everything except read net news (port 119) and transfer files via
FTP (port 21) behind Router Server.
Others are all allowed.
After Inbound Packet Filter setting is configured, click the save button.
Outbound Filter:
To enable Outbound Packet Filter click the check box next to Enable in the Outbound Packet Filter field.
Example 1:
Router LAN IP is 192.168.12.254
(192.168.12.100-192.168.12.149) Located hosts are only allowed to send mail (port 25), receive mail (port
110), and browse Internet (port 80); port 53 (DNS) is necessary to resolve the domain name.
(192.168.12.10-192.168.12.20) Located hosts can do everything (block nothing)
Others are all blocked.
33
Example 2:
Router LAN IP is 192.168.12.254
(192.168.12.100 and 192.168.12.119) Located Hosts can do everything except read net news (port 119) and
transfer files via FTP (port 21)
Others are allowed
After Outbound Packet Filter setting is configured, click the save button.
34
3.3.3.2 Domain filters
Domain Filter
Let you prevent users under this device from accessing specific URLs.
Domain Filter Enable
Check if you want to enable Domain Filter.
Log DNS Query
Check if you want to log the action when someone accesses the specific URLs.
Privilege IP Addresses Range
Setting a group of hosts and privilege these hosts to access network without restriction.
Domain Suffix
A suffix of URL to be restricted. For example, ".com", "xxx.com".
Action
When someone is accessing the URL met the domain-suffix, what kind of action you want.
Check drop to block the access. Check log to log these access.
Enable
Check to enable each rule.
35
Example:
In this example:
1. URL include “www.msn.com” will be blocked, and the action will be record in log-file.
2. URL include “www.sina.com” will not be blocked, but the action will be record in log-file.
3. URL include “www.baidu.com” will be blocked, but the action will not be record in log-file.
4. IP address x.x.x.1~x.x.x.99 can access Internet without restriction.
36
3.3.3.3 URL Blocking
URL Blocking will block LAN computers to connect to pre-defined Websites.
The major difference between “Domain filter” and “URL Blocking” is Domain filter require user to input suffix
(like .com or .org, etc), while URL Blocking require user to input a keyword only. In other words, Domain filter
can block specific website, while URL Blocking can block hundreds of websites by simply a keyword.
URL Blocking Enable
Checked if you want to enable URL Blocking.
URL
If any part of the Website's URL matches the pre-defined word, the connection will be blocked.
For example, you can use pre-defined word "sex" to block all websites if their URLs contain pre-defined word
"sex".
Enable
Checked to enable each rule.
37
In this example:
1. URL include “msn” will be blocked, and the action will be record in log-file.
2. URL include “sina” will be blocked, but the action will be record in log-file
38
3.3.3.4 MAC control
Administrator MAC Control
Regardless the MAC access configuration of administrator, specific MAC can access the device.
This device can record 3 sets. When the host(should be admin) logins Web management, the device will
record MAC address of this host. Before this host configures Internet Access Control , Suggest end-user to
enable this feature, first.
MAC Address Control allows you to assign different access right for different users and to assign a specific IP address to a certain
MAC address.
MAC Address Control
Check “Enable” to enable the “MAC Address Control”. All of the settings in this page will take effect
only when “Enable” is checked.
39
Connection control
Check "Connection control" to enable the controlling of which wired and wireless clients can connect
to this device. If a client is denied to connect to this device, it means the client can't access to the
Internet either. Choose "allow" or "deny" to allow or deny the clients, whose MAC addresses are not in
the "Control table" (please see below), to connect to this device.
Association control Check "Association control" to enable the
controlling of which wireless client can
associate to the wireless LAN. If a client is
denied to associate to the wireless LAN, it
means the client can't send or receive any data
via this device. Choose "allow" or "deny" to
allow or deny the clients, whose MAC
addresses are not in the "Control table", to
associate to the wireless LAN.
Control table
"Control table" is the table at the bottom of the "MAC Address Control" page. Each row of this table
indicates the MAC address and the expected IP address mapping of a client. There are four columns
in this table:
MAC Address
IP Address
MAC address indicates a specific client.
Expected IP address of the corresponding
client. Keep it empty if you don't care its IP
address.
C
When "Connection control" is checked, check
"C" will allow the corresponding client to connect
to this device.
A
When "Association control" is checked, check
"A" will allow the corresponding client to
associate to the wireless LAN.
In this page, we provide the following Combobox and button to help you to input the MAC address.
You can select a specific client in the “DHCP clients” Combobox, and then click on the “Copy to” button to copy the MAC address of
the client you select to the ID selected in the “ID” Combobox.
Previous page and Next Page
To make this setup page simple and clear, we have divided the “Control table” into several
pages. You can use these buttons to navigate to different pages.
Example:
40
In this scenario, there are three clients listed in the Control Table. Clients 1 and 2 are wireless, and client 3 is wired.
1.The "MAC Address Control" function is enabled.
2."Connection control" is enabled, and all of the wired and wireless clients not listed in the "Control table" are "allowed" to connect to this
device.
3."Association control" is enabled, and all of the wireless clients not listed in the "Control table" are "denied" to associate to the wireless
LAN.
4.Clients 1 and 3 have fixed IP addresses either from the DHCP server of this device or manually assigned:
ID 1 - "00-12-34-56-78-90" --> 192.168.12.100
ID 3 - "00-98-76-54-32-10" --> 192.168.12.101
Client 2 will obtain its IP address from the IP Address pool specified in the "DHCP Server" page or
can use a manually assigned static IP address.
If, for example, client 3 tries to use an IP address different from the address listed in the Control
table (192.168.12.101), it will be denied to connect to this device.
5.Clients 2 and 3 and other wired clients with a MAC address unspecified in the Control table are all allowed to connect to this device.
But client 1 is denied to connect to this device.
6.Clients 1 and 2 are allowed to associate to the wireless LAN, but a wireless client with a MAC address not specified in the Control
table is denied to associate to the wireless LAN. Client 3 is a wired client and so is not affected by Association control.
41
3.3.3.5 Miscellaneous Items
Remote Administrator Host/Port
In general, only Intranet user can browse the built-in web pages to perform administration task. This feature
enables you to perform administration task from remote host. If this feature is enabled, only the specified IP
address can perform remote administration. If the specified IP address is 0.0.0.0, any host can connect to
this product to perform administration task. You can use subnet mask bits "/nn" notation to specified a group
of trusted IP addresses. For example, "10.1.2.0/24".
NOTE: When Remote Administration is enabled, the web server port will be shifted to 88. You can change
web server port to other port, too.
Administrator Time-out
The time of no activity to logout automatically. Set it to zero to disable this feature.
Discard PING from WAN side
When this feature is enabled, any host on the WAN cannot ping this product.
SPI Mode
When this feature is enabled, the router will record the packet information pass through the router like IP
address, port address, ACK, SEQ number and so on. And the router will check every incoming packet to
detect if this packet is valid.
DoS Attack Detection
When this feature is enabled, the router will detect and log the DoS attack comes from the Internet. Currently,
the router can detect the following DoS attack: SYN Attack, WinNuke, Port Scan, Ping of Death, Land Attack
etc.
VPN PPTP and IPSec Pass-Through
Virtual Private Networking (VPN) is typically used for work-related networking. For VPN tunnels, the router
supports IPSec Passthrough and PPTP Passthrough.
42
8.4.) ADVANCED SETTINGS
3.3.4.1 System Time
Get Date and Time by NTP Protocol
Selected if you want to Get Date and Time by NTP Protocol.
43
Time Server
Select a NTP time server to consult UTC time
Time Zone
Select a time zone where this device locates.
Set Date and Time manually
Selected if you want to Set Date and Time manually.
Set Date and Time manually
Selected if you want to Set Date and Time manually.
Function of Buttons
Sync Now: Synchronize system time with network time server
Daylight Saving:Set up where the location is.
3.3.4.2 System Log
This page support two methods to export system logs to specific destination by means of syslog(UDP) and
SMTP(TCP). The items you have to setup including:
IP Address for Syslog
Host IP of destination where syslogs will be sent to.
Check Enable to enable this function.
E-mail Alert Enable
Check if you want to enable Email alert (send syslog via email).
SMTP Server IP and Port
Input the SMTP server IP and port, which are concated with ':'. If you do not specify port number, the default
value is 25.
For example, "mail.your_url.com" or "192.168.1.100:26".
Send E-mail alert to
The recipients who will receive these logs. You can assign more than 1 recipient, using ';' or ',' to separate
these email addresses.
44
3.3.4.3 Dynamic DNS
To host your server on a changing IP address, you have to use dynamic domain name service (DDNS).
So that anyone wishing to reach your host only needs to know the name of it. Dynamic DNS will map the
name of your host to your current IP address, which changes each time you connect your Internet service
provider.
Before you enable Dynamic DNS, you need to register an account on one of these Dynamic DNS servers
that we list in provider field.
To enable Dynamic DNS click the check box next to Enable in the DDNS field.
Next you can enter the appropriate information about your Dynamic DNS Server.
You have to define:
Provider
Host Name
Username/E-mail
Password/Key
You will get this information when you register an account on a Dynamic DNS server.
45
3.3.4.4 QoS
This device supports QoS function. User could set specified upstream connection with different priority.
There are three priorities could be selected. The packets with High priority would be processed first.
1.
2.
3.
QoS: Quality of Service.
Local IP/Ports: The IP and ports that LAN side PC used. The value 0 means don’t care.
Remote IP/Ports: The IP and ports that Remote Server used. The value 0 means don’t care.
For example, if you want to guarantee the HTTP bandwidth, you could keep Local IP/Port as 0/0,
Remote IP/Port as 0/80.
46
3.3.4.5 SNMP
In brief, SNMP, the Simple Network Management Protocol, is a protocol designed to give a user the
capability to remotely manage a computer network by polling and setting terminal values and monitoring
network events.
Enable SNMP
You must check Local, Remote or both to enable SNMP function. If Local is checked, this device will
response request from LAN. If Remote is checked, this device will response request from WAN.
Get Community
Setting the community of GetRequest your device will response.
Set Community
Setting the community of SetRequest your device will accept.
IP 1, IP 2, IP 3, IP 4
Input your SNMP Management PC’s IP here. User has to configure to where this device should send SNMP
Trap message.
SNMP Version
Please select proper SNMP Version that your SNMP Management software supports.
WAN Access IP Address
If the user wants to limit to specific the IP address to access, please input in the item. The default 0.0.0.0 and
means every IP of Internet can get some information of device with SNMP protocol.
Click on “Save” to store your setting or “Undo” to give up.
47
3.3.4.6 Routing
Routing Tables allow you to determine which physical interface address to use for outgoing IP data grams.
If you have more than one routers and subnets, you will need to enable routing table to allow packets to find
proper routing path and allow different subnets to communicate with each other.
Routing Table settings are settings used to setup the functions of static.
Dynamic Routing
Routing Information Protocol (RIP) will exchange information about destinations for computing routes
throughout the network. Please select RIPv2 only if you have different subnet in your network.
Otherwise, please select RIPv1 if you need this protocol.
Static Routing: For static routing, you can specify up to 8 routing rules. You can enter the destination IP
address, subnet mask, gateway, hop for each routing rule, and then enable or disable the rule by checking or
unchecking the Enable checkbox.
48
Example:
Configuration on NAT Router
Destination
SubnetMask
Gateway
Hop
Enabled
192.168.1.0
255.255.255.0
192.168.123.216
1
ˇ
192.168.0.0
255.255.255.0
192.168.123.103
1
ˇ
So if, for example, the client3 wanted to send an IP data gram to 192.168.0.2, it would use the above table to
determine that it had to go via 192.168.123.103 (a gateway),
And if it sends Packets to 192.168.1.11 will go via 192.168.123.216
Each rule can be enabled or disabled individually.
After routing table setting is configured, click the save button.
49
3.3.4.7 Schedule Rule
You can set the schedule time to decide which service will be turned on or off. Select
the “enable” item.
Press “Add New Rule”
You can write a rule name and set which day and what time to schedule from “Start Time” to “End Time”. The following example
configure “ftp time” as everyday 14:10 to 16:20
50
Schedule Enable
Selected if you want to Enable the Scheduler.
Edit
To edit the schedule rule.
Delete
To delete the schedule rule, and the rule# of the rules behind the deleted one will decrease one
automatically.
Schedule Rule can be apply to Virtual server and Packet Filter, for example:
Exanple1: Virtual Server – Apply Rule#1 (ftp time: everyday 14:20 to 16:30)
Exanple2: Packet Filter – Apply Rule#1 (ftp time: everyday 14:20 to 16:30).
51
8.5.) TOOLBOX
52
3.3.5.1 View Log
You can View
system log by clicking the View Log button
3.3.5.2 Firmware Upgrade
You can upgrade firmware by clicking Firmware Upgrade button..5.3 Backup Setting
You can backup your settings by clicking the Backup Setting button and save it as a bin file. Once you want
to restore these settings, please click Firmware Upgrade button and use the bin file you saved.
53
3.3.5.4 Reset to default
You can also reset this product to factory default by clicking the Reset to default button.
You can also reboot this product by clicking the Reboot button.
3
.3.5.6 Miscellaneous Items
MAC Address for Wake-on-LAN
Wake-on-LAN is a technology that enables you to power up a networked device remotely. In order to enjoy
this feature, the target device must be Wake-on-LAN enabled and you have to know the MAC address of this
device, say 00-11-22-33-44-55. Clicking "Wake up" button will make the router to send the wake-up frame to
the target device immediately.
Domain Name or IP Address for Test
Allow you to configure an IP, and ping the device. You can ping a secific IP to test whether it is alive.
Safety precautions:
To reduce risk of electric shock, this product should ONLY be opened
authorized technician when service is required. Disconnect the product
and other equipment if a problem should occur. Do not expose the
water or moisture.
by an
from mains
product to
Maintenance:
Clean only with a dry cloth. Do not use cleaning solvents or abrasives.
Warranty:
No guarantee or liability can be accepted for any changes and modifications of the product or damage caused due to incorrect use of
this product.
54
General:
Designs and specifications are subject to change without notice.
All logos brands and product names are trademarks or registered trademarks of their respective holders and are hereby recognized as
such.
Keep this manual and packaging for future reference.
Attention:
This product is marked with this symbol. It means that used electrical and electronic products should not be mixed with
general household waste. There is a separate collections system for these products.
55
Declaration of conformity / Konformitätserklärung / Déclaration de conformité / Conformiteitsverklaring /
Dichiarazione di conformità / Declaración de conformidad Megfelelőségi nyilatkozat / Yhdenmukaisuusvakuutus
/ Överensstämmelseförklaring / Prohlášení o shodě / Declaraţie de conformitate / Δήλωση συμφωνίας /
Overensstemmelse erklæring / Overensstemmelse forklaring
______________________________________________________________________________________
We, / Wir, / Nous, / Wij, / Questa società, / La empresa infrascrita, / Mi, / Me, / Vi, / Společnost, / Noi, / Εμείς:
Nedis B.V., De Tweeling 28, 5215MC, ’s-Hertogenbosch
The Netherlands / Niederlande / Pays Bas / Nederland / Paesi Bassi / Países Bajos / Hollandia / Alankomaat / Holland /
Nizozemí / Olanda / Ολλανδία:
Tel. / Tél / Puh / Τηλ. : 0031 73 5991055
Email / Couriel / Sähköposti / e-post: [email protected]
Declare that product: / erklären, dass das Produkt: / Déclarons que le produit: / verklaren dat het product: / Dichiara che il
prodotto: / Declara que el producto: / Kijelentjük, hogy a termék, amelynek: / Vakuutamme, että: / Intygar att produkten: /
prohlašuje, že výrobek: / Declarăm că acest produs: / Δηλώνουμε ότι το προϊόν: / Forsikrer at produktet, / Forsikrer at
produktet,
Brand: / Marke: / Marque: / Merknaam: / Marca: / Márkája: / Merkki: / Märke: / Značka: / Μάρκα: / mærke: / merke: König
Model: / Modell: / Modèle: / Modello: / Modelo: / Típusa: / Malli: / Μοντέλο:
CMP-WNROUT50, CMP-WNROUT55, CMP-WNROUT60
Description: / Beschreibung: / Description: / Omschrijving: / Descrizione: / Descripción: / Megnevezése: / Kuvaus: /
Beskrivning: / Popis: / Descriere: / Περιγραφή: / Beskrivelse:
EN: Wireless router
DE:
FR:
NL: Draadloze router
IT:
ES:
HU:
FI:
SE:
CZ:
RO:
GR:
DK :
NO :
Is in conformity with the following standards: / den folgenden Standards entspricht: / est conforme aux normes suivantes:
/ in overeenstemming met de volgende normen is: / è conforme ai seguenti standard: / es conforme a las siguientes
normas: / Megfelel az alábbi szabványoknak: / Täyttää seuraavat standardit: / Överensstämmer med följande standarder:
/ splňuje následující normy: / Este în conformitate cu următoarele standarde: / Συμμορφώνεται με τις ακόλουθες
προδιαγραφές: / Overensstemmelse med følgende standarder: / Overensstemmer med følgende standarder: EN609501:2006+A11:2009+A1:2010+A12:2011 / EN62311:2008
EU Directive(s) / EG-Richtlinie(n) / Directive(s) EU / EU richtlijn(en) / Direttiva(e) EU / Directiva(s) UE /
EU direktívák / EU Toimintaohje(et) / Eu Direktiv(en) / Směrnice EU / Directiva(e) UE: / Οδηγία(ες) της ΕΕ / EU
Direktiv(er): 2002/95/EC, 2006/95/EC, 2004/108/EC, 1999/5/EC
‘s-Hertogenbosch, 2012-06-20
Mr. / Hr. / M. / Dhr. / Sig. / Sr. D./ Úr / Mr. / Herr./ Pan / Dl./ Κ. / Hr. / Herr
Randolf Richardson
Chief Operating Officer / Geschäftsführer / Chef des opérations /
Operationeel Directeur / Responsabile Operativo / Director de
Operaciones / Üzemviteli Igazgató / Käyttöpäällikkö / Driftschef /
ředitel / Director principal / Γενικός Διευθυντής Επιχειρήσεων / Chief
Officer / Administrerende Driftsdirektør
Copyright ©
56
Provozní
Operating
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement