Bosch | GLL2-50 Operating/s | Operating instructions | Bosch GLL2-50 Operating/s Operating instructions

OBJ_BUCH-817-004.book Page 1 Thursday, March 19, 2009 12:28 PM
Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
GLL 2-50 Professional
www.bosch-pt.com
1 609 929 S02 (2009.03) T / 334 XXX
de
en
fr
es
pt
it
nl
da
sv
no
fi
el
tr
pl
Originalbetriebsanleitung
Original instructions
Notice originale
Manual original
Manual original
Istruzioni originali
Oorspronkelijke gebruiksaanwijzing
Original brugsanvisning
Bruksanvisning i original
Original driftsinstruks
Alkuperäiset ohjeet
Πρωτότυπο οδηγιών χρήσης
Orijinal işletme talimat
Instrukcja oryginalna
cs
sk
hu
ru
uk
ro
bg
sr
sl
hr
et
lv
lt
Původní návod k používání
Pôvodný návod na použitie
Eredeti használati utasítás
Оригинальное руководство
по эксплуатации
Оригінальна інструкція з
експлуатації
Instrucţiuni originale
Оригинална инструкция
Originalno uputstvo za rad
Izvirna navodila
Originalne upute za rad
Algupärane kasutusjuhend
Instrukcijas oriģinālvalodā
Originali instrukcija
cn
tw
ko
th
id
正本使用说明书
正本使用說明書
사용 설명서 원본
หนังสือคู่มือการใช้งานฉบับต้นแบบ
Petunjuk-Petunjuk untuk
Penggunaan Orisinal
vi BΩng hõëng dÿn nguy›n bΩn
ar ΔϴϠλϷ΍ ϞϴϐθΘϟ΍ ΕΎϤϴϠόΗ
fa ̶Ϡλ΍ έΎ̯ ίήσ ̵ΎϤϨϫ΍έ
OBJ_BUCH-817-004.book Page 2 Thursday, March 19, 2009 12:32 PM
2|
Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seite
6
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page
16
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page
27
Español. . . . . . . . . . . . . . . . . . . . . . . . . . . . Página
37
Português . . . . . . . . . . . . . . . . . . . . . . . . . . Página
47
Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pagina
57
Nederlands . . . . . . . . . . . . . . . . . . . . . . . . . Pagina
67
Dansk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Side
76
Svenska . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sida
85
Norsk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Side
94
Suomi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sivu 103
Ελληνικά . . . . . . . . . . . . . . . . . . . . . . . . . . . Σελίδα 112
Türkçe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sayfa 122
Polski . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strona 131
Česky . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strana 141
Slovensky . . . . . . . . . . . . . . . . . . . . . . . . . . Strana 150
Magyar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oldal 159
Русский . . . . . . . . . . . . . . . . . . . . . . . . Страница 169
Українська . . . . . . . . . . . . . . . . . . . . . . . Сторінка 180
Română . . . . . . . . . . . . . . . . . . . . . . . . . . . Pagina 190
Български . . . . . . . . . . . . . . . . . . . . . . Страница 199
Srpski . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strana 209
Slovensko . . . . . . . . . . . . . . . . . . . . . . . . . . . Stran 218
Hrvatski . . . . . . . . . . . . . . . . . . . . . . . . . Stranica 227
Eesti . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lehekülg 236
Latviešu . . . . . . . . . . . . . . . . . . . . . . . . . Lappuse 245
Lietuviškai . . . . . . . . . . . . . . . . . . . . . . . Puslapis 255
中文 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 页 265
中文 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 頁 273
한국어 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 면 281
ภาษาไทย . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . หน้า
289
Bahasa Indonesia . . . . . . . . . . . . . . . . . . Halaman 298
Tiøng Vi·t . . . . . . . . . . . . . . . . . . . . . . . . . . . Trang 308
vc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ΔΤϔλ
vÝ—U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ϪΤϔλ
1 609 929 S02 | (19.3.09)
317
325
Bosch Power Tools
OBJ_BUCH-817-004.book Page 3 Thursday, March 19, 2009 12:32 PM
3|
2
4
3
5
6
7
1
1
8
18
2 605 438 682
9
OP
EN
10
17
l
na
sio
fes
Pro
1 609 203 X77
15
11
12
13
14
16
14
13
15
1 609 929 S02 | (19.3.09)
Bosch Power Tools
OBJ_BUCH-817-004.book Page 4 Thursday, March 19, 2009 12:32 PM
4|
A
B
C
D
E
F
1 609 929 S02 | (19.3.09)
Bosch Power Tools
OBJ_BUCH-817-004.book Page 5 Thursday, March 19, 2009 12:32 PM
5|
G
H
I
J
K
L
19
2 607 990 031
0 601 015 B00
0 601 015 A00
20
2 607 002 195
21
0 601 096 974
1 609 929 S02 | (19.3.09)
0 601 069 100
Bosch Power Tools
OBJ_BUCH-817-004.book Page 16 Thursday, March 19, 2009 12:32 PM
16 | English
Safety Notes
en
Working safely with the measuring
tool is possible only when the operating and safety information are
read completely and the instructions contained therein are strictly
followed. Never make warning labels on the
measuring tool unrecognisable. SAVE THESE
INSTRUCTIONS.
f Caution – The use of other operating or
adjusting equipment or the application of
other processing methods than those mentioned here, can lead to dangerous radiation exposure.
f The measuring tool is provided with a warning label in English (marked with number 10
in the representation of the measuring tool
on the graphics page).
f Do not use the laser viewing glasses as safety goggles. The laser viewing glasses are used
for improved visualisation of the laser beam,
but they do not protect against laser radiation.
f Do not use the laser viewing glasses as sun
glasses or in traffic. The laser viewing glasses do not afford complete UV protection and
reduce colour perception.
f Have the measuring tool repaired only
through qualified specialists using original
spare parts. This ensures that the safety of
the measuring tool is maintained.
f Do not allow children to use the laser measuring tool without supervision. They could
unintentionally blind other persons or themselves.
f Do not operate the measuring tool in explosive atmospheres, such as in the presence
of flammable liquids, gases or dusts. Sparks
can be created in the measuring tool which
may ignite the dust or fumes.
Functional Description
Do not direct the laser beam at
persons or animals and do not
stare into the laser beam yourself. This measuring tool produces laser class 2 laser radiation according to IEC 60825-1. This can
lead to persons being blinded.
1 609 929 S02 | (19.3.09)
Please unfold the fold-out page with the representation of the measuring tool and leave it unfolded while reading the operating instructions.
Intended Use
The measuring tool is intended for determining
and checking horizontal and vertical lines.
Bosch Power Tools
OBJ_BUCH-817-004.book Page 17 Thursday, March 19, 2009 12:32 PM
English | 17
Technical Data
Cross-line Laser
GLL 2-50
Professional
Article number
3 601 K63 1..
Working range
– Standard
– With pulse function
– With laser receiver
20 m
15 m
50 m
±0.3 mm/m
Levelling Accuracy
Self-levelling range, typically
±4°
Levelling duration, typically
<4 s
Operating temperature
–10 °C ... +50 °C
Storage temperature
–20 °C ... +70 °C
90 %
Relative air humidity, max.
Laser class
2
Laser type
635 nm, <1 mW
C6
1
1/1600 s
Shortest pulse duration
Tripod mount
1/4"
3 x 1.5 V LR6 (AA)
Batteries
12 h
Operating life time, approx.
30 min
Automatic switch-off after approx.
Weight according to EPTA-Procedure 01/2003
0.45 kg
118 x 57 x 89 mm
Dimensions
Degree of protection
IP 54 (dust and splash water protected)
Please observe the article number on the type plate of your measuring tool. The trade names of the individual
measuring tools may vary.
The measuring tool can be clearly identified with the serial number 9 on the type plate.
Bosch Power Tools
1 609 929 S02 | (19.3.09)
OBJ_BUCH-817-004.book Page 18 Thursday, March 19, 2009 12:32 PM
18 | English
Product Features
The numbering of the product features shown
refers to the illustration of the measuring tool
on the graphic page.
1 Exit opening for laser beam
2 Pulse-function indicator
3 Pulse-function button
4 Operating mode button
5 Battery indicator
6 Tripod mount 1/4"
7 On/Off switch
8 Battery lid
9 Serial number
10 Laser warning label
11 Latch of battery lid
12 Alignment plate*
Assembly
Inserting/Replacing the Battery
Use only alkali-manganese batteries.
To open the battery lid 8, press the latch of the
battery lid 11 in the direction of the arrow and
remove the battery lid. Insert the supplied batteries. When inserting, pay attention to the correct polarity according to the representation on
the inside of the battery compartment.
When the battery indication 5 flashes red, the
batteries must be replaced.
Always replace all batteries at the same time.
Only use batteries from one brand and with the
identical capacity.
f Remove the batteries from the measuring
tool when not using it for extended periods.
When storing for extended periods, the batteries can corrode and discharge themselves.
13 0° alignment aid on the alignment plate
14 90° alignment aid on the alignment plate
15 45° alignment aid on the alignment plate
Operation
16 Pin on the alignment plate
Initial Operation
17 Protective pouch*
f Protect the measuring tool against moisture and direct sun irradiation.
f Do not subject the measuring tool to extreme temperatures or variations in temperature. As an example, do not leave it in
vehicles for longer periods. In case of large
variations in temperature, allow the measuring tool to adjust to the ambient temperature
before putting it into operation. In case of
extreme temperatures or variations in temperature, the accuracy of the measuring tool
can be impaired.
f Avoid heavy impact or falling of the measuring tool. After heavy exterior impact on the
measuring tool, an accuracy check should
always be carried out before continuing to
work (see “Levelling Accuracy”).
f Switch the measuring tool off during transport. When switching off, the levelling unit,
which can be damaged in case of intense
movement, is locked.
18 Case*
19 Laser viewing glasses*
20 Measurement plate with stand*
21 Laser receiver*
* The accessories illustrated or described are not
included as standard delivery.
1 609 929 S02 | (19.3.09)
Bosch Power Tools
OBJ_BUCH-817-004.book Page 19 Thursday, March 19, 2009 12:32 PM
English | 19
Switching On and Off
Pulse Function
To switch on the measuring tool, push the
On/Off switch 7 to the “ on” position (when
working without automatic levelling) or to the
“
on” position (when working with automatic
levelling). Immediately after switching on, the
measuring tool sends laser beams out of the exit
openings 1.
f Do not point the laser beam at persons or
animals and do not look into the laser beam
yourself, not even from a large distance.
To switch off the measuring tool, slide the
On/Off switch 7 to the “off” position. When
switching off, the levelling unit is locked.
When working with the laser receiver 21, the
pulse function must be activated, – independent
of the selected operating mode.
Deactivating the Automatic Shut-off
The measuring tool switches off automatically
after an operating duration of 30 minutes. To
deactivate the automatic switch-off, keep the
operating mode button 4 pressed for 3 s while
switching on the measuring tool. When the automatic switch-off is deactivated, the laser lines
briefly flash after 3 s.
f Do not leave the switched on measuring
tool unattended and switch the measuring
tool off after use. Other persons could be
blinded by the laser beam.
To activate the automatic shut-off, switch the
measuring tool off and then on again (without
the operating mode button 4 pushed).
Operating Modes (see figures A–D)
The measuring tool has three operating modes
between which you can switch at any time:
– Horizontal operation “–”: Produces a horizontal laser line,
– Vertical operation “l”: Produces a vertical
laser line,
– Cross-line operation “+”: Produces a horizontal and vertical laser line.
After switching on, the measuring tool is in
cross-line operating mode. To change the operating mode, press the operating mode button 4.
All three operating modes can be selected either
with or without automatic levelling.
Bosch Power Tools
In pulse function, the laser lines flash at very
high frequency and thus become detectable for
the laser receiver 21.
To switch on the pulse function, press button 3.
When the pulse function is switched on, the
pulse-function indicator 2 lights up green.
When the pulse function is switched on, the
visibility of the laser lines is reduced for the
human eye. Therefore, shut off the pulse function by pushing button 3 again when working
without laser receiver. When the pulse function
is switched off, the pulse-function indicator 2
is deactivated.
Automatic Levelling
Working with Automatic Levelling
(see figure C)
Position the measuring tool on a level and firm
support or attach it to a commercially available
photographic tripod.
When working with automatic levelling, push
the On/Off switch 7 to the “
on” position.
After switching on, the levelling function automatically compensates irregularities within the
self-levelling range of ±4°. The measuring tool is
levelled in as soon as the laser lines no longer
flash.
If the automatic levelling function is not possible, e.g. because the surface on which the
measuring tool stands deviates by more than 4°
from the horizontal plane, the laser beams flash.
In this case, bring the measuring tool to the level
position and wait for the self-levelling to take
place.
In case of ground vibrations or position changes
during operation, the measuring tool is automatically levelled in again. To avoid errors, check
the position of the horizontal and vertical laser
line with regard to the reference points upon
re-levelling.
1 609 929 S02 | (19.3.09)
OBJ_BUCH-817-004.book Page 20 Thursday, March 19, 2009 12:32 PM
20 | English
Working without Automatic Levelling
(see figure D)
Checking the Height Accuracy
of the Horizontal Line
For work without automatic levelling, push the
On/Off switch 7 to the “ on” position. When
the automatic levelling is switched off, the laser
lines flash continuously.
For this check, a free measuring distance of
5 metres on a firm surface between two walls A
and B is required.
When the automatic levelling is switched off, the
measuring tool can be held by hand or placed on
an inclined surface. In cross-line operation, the
two laser lines do not necessarily run at a right
angle to each other.
– Mount the measuring tool onto a tripod or
place it on a firm and level survace close to
wall A. Switch on the measuring tool. Select
cross-line operation with automatic levelling.
A
B
Levelling Accuracy
Influences on Accuracy
The ambient temperature has the greatest influence. Especially temperature differences
occurring from the ground upward can divert
the laser beam.
Because the largest difference in temperature
layers is close to the ground, the measuring tool
should always be mounted on a tripod when
measuring distances exceeding 20 m. If possible, also set up the measuring tool in the centre
of the work area.
Apart from exterior influences, device-specific
influences (such as heavy impact or falling
down) can lead to deviations. Therefore, check
the accuracy of the measuring tool each time
before starting your work.
5m
– Direct the laser against the close wall A and
allow the measuring tool to level in. Mark the
centre of the point where the laser lines
cross each other on the wall (point I).
A
B
180˚
First, check both the height as well as the levelling accuracy of the horizontal laser line, then
the levelling accuracy of the vertical laser line.
Should the measuring tool exceed the maximum
deviation during one of the tests, please have it
repaired by a Bosch after-sales service.
1 609 929 S02 | (19.3.09)
– Turn the measuring tool by 180°, allow it to
level in and mark the cross point of the laser
lines on the opposite wall B (point II).
Bosch Power Tools
OBJ_BUCH-817-004.book Page 21 Thursday, March 19, 2009 12:32 PM
English | 21
– Without turning the measuring tool, position
it close to wall B. Switch the measuring tool
on and allow it to level in.
A
B
Checking the Levelling Accuracy
of the Horizontal Line
For the check, a free surface of approx.
5 x 5 metres is required.
– Set up the measuring tool on a firm, level surface between both walls A and B. Allow the
measuring tool to level in while in horizontal
operation.
A
– Align the height of the measuring tool (using
a tripod or by underlaying, if required) in
such a manner that the cross point of the laser lines is projected against the previously
marked point II on the wall B.
m
2
,5
m
5,0
B
A
180˚
B
d
– At a distance of 2.5 metres from the measuring tool, mark the centre of the laser line
(point I on wall A and point II on wall B) on
both walls.
A
The maximum permitted deviation dmax is calculated as follows:
dmax = double distance of the walls x 0.3 mm/m
Example: With a 5 metre distance between the
walls, the maximum deviation must not exceed
dmax = 2 x 5 m x 0.3 mm/m = 3 mm. Thus, the
marks must not be more than 3 mm apart.
Bosch Power Tools
m
,5
2
– The difference d of both marked points I and
III on wall A indicates the actual height deviation of the measuring tool.
d
– Without changing the height, turn around the
measuring tool by 180°. Direct it against the
wall A in such a manner that the vertical laser
line runs through the already marked point I.
Allow the measuring tool to level in and mark
the cross point of the laser lines on the wall
A (point III).
B
– Set up the measuring tool 5 metres away
turned by 180° and allow it to level in.
– Align the height of the measuring tool (using a
tripod or by underlaying, if required) in such a
manner that the centre of the laser line is projected exactly against the previously marked
point II on wall B.
1 609 929 S02 | (19.3.09)
OBJ_BUCH-817-004.book Page 22 Thursday, March 19, 2009 12:32 PM
22 | English
d
2m
– Mark the centre of the laser line as point III
(vertically above or below point I) on the wall
A.
– The difference d of both marked points I and
III on wall A indicates the actual deviation of
the measuring tool from the level plane.
The maximum permitted deviation dmax is calculated as follows:
dmax = double distance of the walls x 0.3 mm/m
Example: With a 5 metre distance between the
walls, the maximum deviation must not exceed
dmax = 2 x 5 m x 0.3 mm/m = 3 mm. Thus, the
marks must not be more than 3 mm apart.
For this check, a door opening is required with
at least 2.5 metres of space (on a firm surface)
to each side of the door.
– Position the measuring tool on the other side
of the door opening directly behind point II.
Allow the measuring tool to level in and align
the vertical laser line in such a manner that
its centre runs exactly throught points I
and II.
– Position the measuring tool on a firm, level
surface (not on a tripod) 2.5 m away from the
door opening. Allow the measuring tool to level in while in cross-line operation mode, and
direct the laser beams at the door opening.
– The difference d between point III and the
centre of the laser line at the upper edge of
the door opening results in the actual deviation of the measuring tool from the vertical
plane.
Checking the Levelling Accuracy of the Vertical Line
The maximum permitted deviation dmax is calculated as follows:
dmax = double height of the door opening
x 0.3 mm/m
Example: With a door opening height of 2 metres, the maximum permitted deviation is
dmax = 2 x 2 m x 0.3 mm/m = 1.2 mm. Thus, the
marks must not be more than 1.2 mm apart.
2
,5
m
2
,5
m
– Measure the height of the door opening.
– Mark the centre of the vertical laser line at
the floor of the door opening (point I), at a
distance of 5 metres beyond the other side of
the door opening (point II) and at the upper
edge of the door opening (point III).
1 609 929 S02 | (19.3.09)
Bosch Power Tools
OBJ_BUCH-817-004.book Page 23 Thursday, March 19, 2009 12:32 PM
English | 23
Working Advice
f Always use the centre of the laser line for
marking. The width of the laser line changes
with the distance.
Working with the Alignment Plate
With the alignment plate 12, the measuring tool
can be aligned by a reference line or the vertical
laser line can be indicated at an angle of 45° or
90° to a reference line.
Position the measuring tool via the tripod mount
6 onto the pin 16 of the alignment plate. Position it in such a manner on the alignment plate
that the vertical laser line (depending on the requested angle) runs centrally through the alignment aid 13, 14 or 15.
Align the alignment plate 12 with the corresponding alignment aids 13, 14 or 15 to the
desired reference line.
Working with the Measuring Plate (Accessory)
(see figures E–F)
With the measuring plate 20, it is possible to
project the laser mark onto the floor or the laser
height onto a wall.
With the zero field and the scale, the offset or
drop to the required height can be measured
and projected at another location. This eliminates the necessity of precisely adjusting the
measuring tool to the height to be projected.
The measuring plate 20 has a reflective coating
that enhances the visibility of the laser beam at
greater distances or in intense sunlight. The
brightness intensification can be seen only
when viewing, parallel to the laser beam, onto
the measuring plate.
Working with the Tripod (Accessory)
A tripod offers a stable, height-adjustable measuring support. Place the measuring tool via the
tripod mount 6 onto the 1/4" male thread of the
tripod and screw the locking screw of the tripod
tight.
Bosch Power Tools
Working with the Laser Receiver (Accessory)
(see figure G)
Under unfavourable light conditions (bright
environment, direct sunlight) and for larger
distances, use the laser receiver for improved
finding of the laser lines 21. When working with
the laser receiver, switch the pulse function on
(see “Pulse Function”, page 19).
Laser Viewing Glasses (Accessory)
The laser viewing glasses filter out the ambient
light. This makes the red light of the laser appear brighter for the eyes.
f Do not use the laser viewing glasses as
safety goggles. The laser viewing glasses are
used for improved visualisation of the laser
beam, but they do not protect against laser
radiation.
f Do not use the laser viewing glasses as sun
glasses or in traffic. The laser viewing glasses do not afford complete UV protection and
reduce colour perception.
Work Examples (see figures H–K)
Laying Flooring Plates at a 45° Angle
(see figure J)
Position the measuring tool via the tripod mount
6 onto the pin 16 of the alignment plate. Position it in such a manner on the centred protrusion of the alignment plate 12 that the vertical
laser line runs centrally through the alignment
aid 15. Then, align the alignment plate with the
alignment aids 13 or 14 with regard to the reference line.
For cross line or in vertical operation, the vertical laser line on the floor indicates a 45° angle
to the reference line. Align the flooring plates
with regard to this line.
1 609 929 S02 | (19.3.09)
OBJ_BUCH-817-004.book Page 24 Thursday, March 19, 2009 12:32 PM
24 | English
Projecting Plumb Points to the Ceiling
(see figure K)
Draw two lines crossed at a right angle through
the point that you want to project to the ceiling.
Place the alignment plate 12 onto the crossed
lines and align it with the alignment aids 13 and
14 on the cross.
Accessories
Protective Pouch 17 . . . . . . . . . 1 609 203 X77
Case 18 . . . . . . . . . . . . . . . . . . . 2 605 438 682
Laser Viewing Glasses 19 . . . . . 2 607 990 031
Measuring plate with foot 20 . . . 2 607 002 195
Position the measuring tool via the tripod mount
6 onto the pin 16 of the alignment plate. Position it in such a manner on one of the two outer
protrusions on the alignment plate that the vertical laser line runs centrally through the corresponding alignment aid 13 or 14. Select vertical
operation and draw the centre of the line running across the measuring tool to the ceiling.
Laser Receiver 21 . . . . . . . . . . . 0 601 069 100
Turn the measuring tool on the alignment plate
by 90°. Pay attention not to move the position
of the alignment plate. After levelling in, draw
the cross point of the vertical laser line to the already drawn line. The cross point of both lines
is the projected plumb point.
Our after-sales service responds to your questions concerning maintenance and repair of your
product as well as spare parts. Exploded views
and information on spare parts can also be
found under:
www.bosch-pt.com
Our customer consultants answer your questions concerning best buy, application and adjustment of products and accessories.
Maintenance and Service
Maintenance and Cleaning
Store and transport the measuring tool only in
the protective pouch 17 or in the case 18.
Keep the measuring tool clean at all times.
Do not immerse the measuring tool into water
or other fluids.
Wipe off debris using a moist and soft cloth.
Do not use any cleaning agents or solvents.
Regularly clean the surfaces at the exit opening
of the laser in particular, and pay attention to
any fluff of fibres.
If the measuring tool should fail despite the care
taken in manufacturing and testing procedures,
repair should be carried out by an authorized
after-sales service centre for Bosch power tools.
Do not open the measuring tool yourself.
In all correspondence and spare parts orders,
please always include the 10-digit article number
given on the type plate of the measuring tool.
Construction tripod BS 150 . . . . 0 601 096 974
Universal holder BM 1 . . . . . . . . 0 601 015 A00
Telescopic rod BT 350 . . . . . . . . 0 601 015 B00
After-sales Service and Customer
Assistance
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
For repairs, only send in the measuring tool in
the protective pouch 17 or in the case 18.
1 609 929 S02 | (19.3.09)
Bosch Power Tools
OBJ_BUCH-817-004.book Page 25 Thursday, March 19, 2009 12:32 PM
English | 25
Australia, New Zealand and Pacific Islands
Philippines
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Robert Bosch, Inc.
Zuellig Building
Sen. Gil Puyat Avenue
Makati City 1200, Metro Manila
Philippines
Tel.: +63 (2) 8 17 32 31
www.bosch.com.ph
People’s Republic of China
Website: www.bosch-pt.com.cn
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 800 8 20 84 84
Tel.: +86 (571) 87 77 43 38
Fax: +86 (571) 87 77 45 02
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King’s Road
North Point, Hong Kong
Customer Service Hotline: +852 (21) 02 02 35
Fax: +852 (25) 90 97 62
E-Mail: info@hk.bosch.com
www.bosch-pt.com.cn
Indonesia
PT. Multi Tehaka
Kawasan Industri Pulogadung
Jalan Rawa Gelam III No. 2
Jakarta 13930
Indonesia
Tel.: +62 (21) 4 60 12 28
Fax: +62 (21) 46 82 68 23
E-Mail: sales@multitehaka.co.id
www.multitehaka.co.id
Bosch Power Tools
Malaysia
Robert Bosch (SEA.) Pte. Ltd.
No. 8a, Jalan 13/6
46200 Petaling Jaya,
Selangor,
Malaysia
Tel.: +6 (03) 7966 3000
Fax: +6 (03) 7958 3838
E-Mail: hengsiang.yu@my.bosch.com
Toll Free Tel.: 1 800 880 188
Fax: +6 (03) 7958 3838
www.bosch.com.sg
Thailand
Robert Bosch Ltd.
Liberty Square Building
No. 287, 11 Floor
Silom Road, Bangrak
Bangkok 10500
Tel.: +66 (2) 6 31 18 79 – 18 88 (10 lines)
Fax: +66 (2) 2 38 47 83
Robert Bosch Ltd., P. O. Box 2054
Bangkok 10501, Thailand
Bosch Service – Training Centre
2869-2869/1 Soi Ban Kluay
Rama IV Road (near old Paknam Railway)
Prakanong District
10110 Bangkok
Thailand
Tel.: +66 (2) 6 71 78 00 – 4
Fax: +66 (2) 2 49 42 96
Fax: +66 (2) 2 49 52 99
1 609 929 S02 | (19.3.09)
OBJ_BUCH-817-004.book Page 26 Thursday, March 19, 2009 12:32 PM
26 | English
Singapore
Battery packs/batteries:
Robert Bosch (SEA.) Pte. Ltd.
38 C Jalan Pemimpin
Singapore 915701
Republic of Singapore
Tel.: +65 (3) 50 54 94
Fax: +65 (3) 50 53 27
www.bosch.com.sg
Do not dispose of battery packs/batteries into
household waste, fire or water. Battery packs/
batteries should be collected, recycled or disposed of in an environmental-friendly manner.
Vietnam
Robert Bosch (SEA) Pte. Ltd – Vietnam
Representative Office
Saigon Trade Center, Suite 1206
37 Ton Duc Thang Street,
Ben Nghe Ward, District 1
HCMC
Vietnam
Tel.: +84 (8) 9111 374 – 9111 375
Fax: +84 (8) 9111376
Disposal
Measuring tools, accessories and packaging
should be sorted for environmental-friendly recycling.
Only for EC countries:
Only for EC countries:
Defective or dead out battery packs/batteries
must be recycled according the guideline
91/157/EEC.
Batteries no longer suitable for use can be
directly returned at:
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Subject to change without notice.
Do not dispose of measuring tools
into household waste!
According the European Guideline
2002/96/EC for Waste Electrical
and Electronic Equipment and its
implementation into national
right, measuring tools that are no longer usable
must be collected separately and disposed of in
an environmentally correct manner.
1 609 929 S02 | (19.3.09)
Bosch Power Tools
Download PDF

advertising