red lion MLPS HMI & Panel Meter Accessory Product manual

Below you will find brief information for Micro-Line MLPS. The MLPS is a +12 VDC power supply designed to attach to the rear of backlight versions of the Micro-Line Series. The MLPS can be powered from either a 115 VAC or 230 VAC source and is switch selectable. The maximum output current of the MLPS is 80 mA. It is UL Recognized Component and complies with IECEE CB Scheme, IEC 1010-1, EMC standards EN 50082-2, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-6, EN 61000-4-8, EN 50081-1 and EN 55011.

PDF Download

Document

Bulletin No. MLPS-I

Drawing No. LP0231

Released 4/03

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839 www.redlion-controls.com

MODEL MLPS - MICRO-LINE POWER SUPPLY

PROVIDES +12 VDC POWER TO BACKLIGHT VERSIONS OF

THE MICRO-LINE SERIES

115/230 VAC SWITCH SELECTABLE

12 VDC OUTPUT @ 80 mA

EASILY ATTACHED TO BACKLIGHT VERSIONS

UL Recognized Component,

File # E143054

DESCRIPTION

The Model MLPS is a +12 VDC power supply designed to attach to the rear of backlight versions of the Micro-Line Series. The MLPS can be powered from either a 115 VAC or 230 VAC source and is switch selectable.

Caution: The maximum output current of the MLPS is 80 mA. Check the specifications of the specific counter(s)/indicators(s) and sensors(s) being used to ensure that total current requirements do not exceed 80 mA.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in the manual or on equipment must be observed to ensure personal safety and to prevent damage to either the instrument or equipment connected to it. If equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

CAUTION: Read complete instructions prior to installation and operation of the unit.

CAUTION:

Risk of electric shock.

SPECIFICATIONS

1. POWER REQUIREMENTS: Switch selectable 115/230 VAC (±10%),

50/60 Hz, 3 VA. The unit is shipped from factory in the 230 VAC position.

2. POWER OUTPUT: +12 VDC (+5/-25%) @ 80 mA max.

The MLPS is listed in the UL Recognized Component Directory Category

QQFU2 as having an Output category (OC) of NEC Class 2.

3. ENVIRONMENTAL CONDITIONS:

Operating Temperature: 0 to 60°C

Storage Temperature: -30 to 75°C

Operating and Storage Humidity: 85% max. (non-condensing) from 0°C to 50°C.

Altitude: Up to 2000 meters

4. CERTIFICATIONS AND COMPLIANCES:

SAFETY

UL Recognized Component, File # E143054, UL1012, CSA 22.2 No. 107.1

Recognized to U.S. and Canadian requirements under the Component

Recognition Program of Underwriters Laboratories Inc.

ORDERING INFORMATION

MODEL NO.

MLPS

DESCRIPTION

Micro Line/Sensor Power Supply

PART NUMBER

MLPS0000

DIMENSIONS In inches (mm)

SPECIFICATIONS (Cont’d)

4. CERTIFICATIONS AND COMPLIANCES: (Cont’d)

IECEE CB Scheme Test Certificate # US/5685/UL

CB Scheme Test Report # 01ME22279-01302002

Issued by Underwriters Laboratories, Inc.

IEC 1010-1, EN 61010-1: Safety requirements for electrical equipment for measurement, control, and laboratory use, Part 1.

ELECTROMAGNETIC COMPATIBILITY

Immunity to EN 50082-2

Electrostatic discharge

Electromagnetic RF fields

Fast transients (burst)

RF conducted interference

EN 61000-4-2 Level 2; 4 Kv contact

Level 3; 8 Kv air

EN 61000-4-3 Level 3; 10 V/m

80 MHz - 1 GHz

EN 61000-4-4 Level 4; 2 Kv I/O

Level 3; 2 Kv power

EN 61000-4-6 Level 3; 10 V/rms

150 KHz - 80 MHz

EN 61000-4-8 Level 4; 30 A/m Power frequency magnetic fields

Emissions to EN 50081-1

RF interference EN 55011 Enclosure class B

Power mains class B

5. CONSTRUCTION: High impact black plastic. Two hex stand-offs and two washers included. Installation Category II, Pollution Degree 2.

6. CONNECTION: Two position terminal block which accepts one 14 AWG wire (torque terminal screws to 5 inch-lbs. [-6Nm]).

7. WEIGHT: 4 oz (113 g)

TROUBLESHOOTING

For further technical assistance, contact technical support at the appropriate company numbers listed.

INSTALLATION ENVIRONMENT

The unit should be installed in a location that does not exceed the maximum operating temperature and provides good air circulation. Placing the unit near devices that generate excessive heat should be avoided.

Installation Procedure

The MLPS is shipped with all the necessary hardware to mount to the rear of an installed backlight version Micro-

Line unit. The user must remove the common and V+ screw terminals on the rear of the Micro-Line unit (Save these screw terminals for later use). Install the

1/4" hex drive stand-offs into the common and V+ terminals. The MLPS is then mounted to the stand-offs using the screw terminals from the compatible

Micro-Line unit with the supplied square washers. AC power can then be connected to the terminal block of the

MLPS.

Note: Make sure the A.C.

selector switch is set to the appropriate position before applying power to the unit.

Red Lion Controls

20 Willow Springs Circle

York PA 17402

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

Red Lion Controls BV

Basicweg 11b

NL - 3821 BR Amersfoort

Tel +31 (0) 334 723 225

Fax +31 (0) 334 893 793

Red Lion Controls Asia

31, Kaki Bukit Road 3 #06-04/05 TechLink

Singapore 417818

Tel +65 6744-6613

Fax +65 6743-3360

Hello! I am an AI chatbot specifically trained to assist you with the red lion MLPS HMI & Panel Meter Accessory Product manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated

Key Features

+12 VDC output
Switch selectable 115/230 VAC
UL Recognized Component
Easy attachment to backlight versions
Complies with IECEE CB Scheme, IEC 1010-1, EMC standards
Installation Category II, Pollution Degree 2
2 position terminal block

Frequently Answers and Questions

What is the maximum output current of the MLPS?

The maximum output current of the MLPS is 80 mA.

What are the power requirements of the MLPS?

The MLPS requires Switch selectable 115/230 VAC (±10%), 50/60 Hz, 3 VA. It ships from the factory in the 230 VAC position.

What are the environmental conditions for the MLPS?

The MLPS has an operating temperature of 0 to 60°C, storage temperature of -30 to 75°C, operating and storage humidity of 85% max. (non-condensing) from 0°C to 50°C, and an altitude of up to 2000 meters.

What certifications and compliances does the MLPS meet?

The MLPS is UL Recognized Component, File # E143054, UL1012, CSA 22.2 No. 107.1, IECEE CB Scheme Test Certificate # US/5685/UL, CB Scheme Test Report # 01ME22279-01302002, IEC 1010-1, EN 61010-1, EN 50082-2, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-6, EN 61000-4-8, EN 50081-1 and EN 55011.