NMTG-S12864BFYHSGY-C скачать даташит

NMTG-S12864BFYHSGY-C скачать даташит
Messrs.
Product Specification Model:
NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24,11
LCD MODULE SPECIFICATION
FOR CUSTOMER’S APPROVAL
CUSTOMER
:
MODULE TYPE :
NMTG-S12864BFYHSGY-C
APPROVED BY: (FOR CUSTOMER USE ONLY)
Approved by
微 端
2011/02/24
李剛
Checked by
Made by
微 端
微 端
微 端
2011/02/24
2011/02/24
2011/02/24
陳世文
翟玉東
許瓊窈
Page.
1 / 21
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
2 / 21
Revise Records
Rev.
Date
Contents
Written
Approved
A
2011/02/24
Initial Edition
Jill Hsu
Steele Lee
Special Notes
Note1.
Note2.
Note3.
Note4.
Note5.
Avant IC updated edition.
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
CONTENTS
ITEM
PAGE
FEATURES
GENERAL SPECIFICATION
4
5
ABSOLUTE MAXIMUM RATING
5
ELECTRICAL OPTICAL
6
BACKLIGHT ABSOLUTE MAXIMUM RATING
6
ELECTRICAL CHARACTERISTIC
7
OPTICAL CHARACTERISTIC
7
INTERFACE PIN ASSIGNMENT
10
BLOCK DIAGRAM
11
POWER SUPPLY DIAGRAM
11
TIMING CHARACTERISTICS
12
DISPLAY COMMANDS
14
MEMORY MAPPING
15
ADDRESS CONFIGURATION OF DISPLAY DATA RAM
16
RELIABILITY TEST
17
APPEARANCE CHECK
17
HANDLING PRECAUTIONS
18
LCD PRODUCT QUALITY STANDARD
19
WARRANTY
20
DIMENSIONAL OUTLINES
21
Page.
3 / 21
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
4 / 21
SPECIFICATION FOR
LIQUID CRYSTAL DISPLAY MODULE
MODEL NO. :
View Direction
LCD Type
NMTG-S12864BFYHSGY-C
; 6 O’clock
…12 O’clock
… FSTN Positive
… FSTN Negative
… STN Gray
; STN Yellow Green … STN Blue
Rear Polarizer
… Reflective
; Transflective
Backlight Type
; LED
… Transmissive
… EL
; Internal Power
; 5V input
… CCFL
… External Power
… 24V input
Backlight Color … White
… Amber
…
Blue
Green
;
Temperature
Range
… Normal
EL Driver IC
… Build-in
; Not Build-in
Touch Screen
… With
; Without
LCD LSI
; Wide
Yellow
Green
… Other
… Super Wide
SBN640G21 / SBN0064G-D
TO BE VERY CAREFUL !
The LCD driver ICs are made by CMOS process, which are very easy to be damaged by static
charge, make sure the user is grounded when handling the LCM.
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
5 / 21
GENERAL SPECIFICATION
Item
Display Resolution
Dimensional Outline(mm)
Dot Size
Dot Pitch
Display mode
Circuit
Interface
Content
128(W)×64(H)
75.0(W)×52.7(H)×9.0max(D)
0.40(W)mm×0.40(H)mm
0.43(W)mm×0.43(H)mm
Transflective/ Positive Type
Avant IC
Data (D0~D7), D/I, R/W, E, RST, CS1, CS2, VEE
ABSOLUTE MAXIMUN RATING
(1) Electrical Absolute Ratings
Item
Symbol
Min.
Max.
Power Supply for Logic
VDD – VSS
-0.3
7.0
Power Supply for LCD
VDD – VEE
-0.3
19.0
Input Voltage
VI
-0.3
VDD+0.3
Current for LED backlight
--200
Static Electricity
---Note 1: Operator should be grounded during handling LCM.
(2) Environmental Absolute Maximum Ratings
Normal Temperature
Operating
Storage
Item
Max,
Min.
Max,
Min.
Ambient Temperature
0℃
+50℃ -20℃ +70℃
Humidity(without
condensation)
Note 2,4
Note 3,5
Unit
Volt
Volt
Volt
mA
--
Note
----Note 1
Wide Temperature
Operating
Storage
Max,
Min.
Max,
Min.
-20℃ +70℃ -30℃ +80℃
Note 4,5
Note 4,6
Note 2: Ta≦50℃: 80% RH max
Ta>50℃: Absolute humidity must be lower than the humidity of 85%RH at 50℃
Note 3: Ta at -20℃ will be<48hrs at 70℃will be <120hrs when humidity is higher than 75%.
Note 4: Background color changes slightly depending on ambient temperature. This phenomenon is
reversible.
Note 5: Ta≦70℃: 75RH max
Ta>70℃: absolute humidity must be lower than the humidity of 75%RH at 70℃
Note 6: Ta at -30℃ will be <48hrs, at 80 ℃ will be <120hrs when humidity is higher than 75%.
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Page.
6 / 21
Feb. 24, 11
ELECTRICAL OPTICAL
Characteristics
Parameter
Ta = 25℃
Symbol
Rating
Min.
Typ
Max.
Unit
Test
Condition
Total Forward Voltage
VF
3.8
4.05
4.3
V
--
Average Luminous Intensity
IV
18
25
--
cd/㎡
--
IV-m
50
--
--
%
--
Chromaticity Coordinate *
X
0.4000
0.4441
0.4878
--
--
Chromaticity Coordinate *
y
0.5906
0.5547
0.5152
--
--
Luminous Tolerance
Note1: This product must be in VF MAX. under the testing.
Note2: The current should be set at 2x50mA when the finished goods is under the testing.
BACKLIGHT ABSOLUTE MAXIMUM RATING
Ta = 25℃
Parameter
Symbol
Rating
Unit
Power Dissipation
Po
860
W
Peak Forward Current
IF
200
mA
Reverse Voltage
VR
8
V
Operating Temperature Range
TOPR
-20℃ TO + 70℃
--
Storage Temperature Range
TSTO
-30℃ TO + 80℃
--
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Page.
7 / 21
Feb. 24, 11
ELECTRICAL CHARACTERISTICS
Item
Symbol
Condition
Min.
Typ
Max.
Unit
Power Supply
for Logic
VDD – VSS
--
4.5
5.0
5.5
Volt
VIL
L level
0
--
0.8
Volt
VIH
H level
VDD-2.2
--
VDD
Volt
--
1.5
1.8
mA
--
0.6
1.0
--
100
150
--
100V/
400Hz
--
Input Voltage
Power Supply
Current for
LCM
IDD(LED
B/L OFF)
IEE
ILED
Power Supply
for EL
Backlight
VEL
VDD = 5.0V
Ta = 25℃
VDD – VEE
= 10.3V
VLED = 5.0V
--
--
OPTICAL CHARACTERISTICS
Item
LCM
Recommend
LCD Module
Driving
Voltage
Symbol
Vop
Condition
Min.
Typ
Max.
Ta = -20℃
9.14
9.64
10.14
Ta = 25℃
8.60
9.10
9.60
Ta = 70℃
8.06
8.56
9.06
Unit
note
Volt
1.
Viewing
Angle
Front-Back
θ =0°
30
92
--
deg.
Left-Right
θ =0°
60
90
--
deg.
Rise Time
Tr
--
90
220
Fall Time
Tf
--
210
200
Contrast
Cr
2.0
6.0
--
VDD - VEE
=10.3V
Ta = 25℃
3.
mS
2.
--
4
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
[Note 1] Definition of Operation Voltage (Vop)
θ = 0°
ψ= 0°
[Note 2] Definition of Response Time (Tr, Tf)
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
8 / 21
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
[Note 3] Definition of Angle θ&ψ
[Note 4] Description of Contrast Ratio (K)
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
9 / 21
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
10 / 21
INTERFACE PIN ASSIGNMENT
Pin No.
Pin Out
I/O
1.
VDD
--
Logic supply voltage
2.
VSS
--
GND
3.
VEE
--
Supply Voltage for LCD panel.
4.
|
11.
DB0
|
DB7
I/O
12.
/CS1
I
Chip-select for the left half of the display. Active LOW.
13.
/CS2
I
Chip-select for the right half of the display. Active LOW.
I
Setting the RES signal to Low level can initialize the following
registers.
1. ON/OFF register 0 set(Display off)
2. Display start line register 0 set(display starts from line 0)
After releasing reset, this condition can be changed only by
software.
I
Read/Write
R/W=high:Data of DB0~DB7 can be read by CPU.
R/W=low:Data of DB0~DB7 can be written into LCD driver IC
at the falling edge of E when CS1 and CS2 is high.
14.
15.
/RST
R/W
Description
Data bus. 3-state I/O common terminal.
Data/Instruction
D/I=high:Indicates that data of DB0~DB7 is display data.
D/I=low:Indicates that data of DB0~DB7 is instruction.
Enable
When write(R/W=low):Data of DB0~DB7 is latched at the
fall of E
When read(R/W=high):Data is read while E is at high level.
16.
D/I
I
17.
E
I
18.
FGND
--
Frame Ground
19.
BKLA
--
20.
BKLK
--
Power supply for backlight.
(4.2V/100~150 mA DC for LED backlight, 110V/400Hz AC for
EL)
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
BLOCK DIAGRAM
POWER SUPPLY
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
11 / 21
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
TIMING CHARACTERISTICS
MPU interface timing: (VSS =0V, VDD=4.5V~5.5V, Ta=-20 to 60℃)
Item
Symbol
Min.
Typ.
Max.
Unit
tC
1000
--
--
ns
E High Level Width
tWH
450
--
--
ns
E Low Level Width
tWL
450
--
--
ns
E Rise Time
tR
--
--
25
ns
E Fall Time
tF
--
--
25
ns
Address Setup Time
tASU
140
--
--
ns
Address Hold Time
tAH
10
--
--
ns
Data Setup Time
tDSU
200
--
--
ns
Data Delay Time
tD
--
--
320
ns
Data Hold Time(Write)
tDHW
10
--
--
ns
Data Hold Time(Read)
tDHR
20
--
--
ns
E Cycle Time
Page.
12 / 21
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
13 / 21
Messrs.
Rev. No. Issued Date.
Product Specification Model: NMTG-S12864BFYHSGY-C
A
Feb. 24, 11
Page.
14 / 21
DISPLAY COMMANDS
The display commands shown below control the internal state of the LCD driver ICs. Commands
are sent from CPU to LCD module for the display control.
Command
RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
Display
ON/OFF
0
0
0
0
Set address
(Y address)
0
0
0
1
Set page
(X address)
0
0
1
0
Display Start
Line
0
0
1
1
Busy
0
1
1
1
1
1
To control the display ON or
OFF. The internal status and
1/0 display RAM data are not
affected.
0:OFF, 1:ON
To set the Y address in the Y
address counter.
Y address (0~63)
1
1
1
To set the X address at the X
address register.
Page(0~7)
To indicate the display data RAM
displayed at the top of the screen.
Display Start Line(0~63)
ON/ Rese
OFF t
0
0
0
Function
0
To read status of the LCD
controller IC:
Busy
0:Ready, 1: In operation
ON/OFF:
0:Display ON, 1:Display OFF
Reset:
0:Normal, 1:Reset
Status Read
0
1
Write display
data
1
0
Write Data
To write data into display data
RAM. Y address is increased by
1 after this command.
Read Display
data
1
1
Read Data
To read data from display data
RAM to the data bus.
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
MEMORY MAPPING
………
Line 0→
Line 1→
Line 2→
Line 3→
Line 7→
Line 8→
Line 9→
Line 10→
…………
2nd
page(X=1)
1st
page(X=0)
Relationship between RAM data and display
1
0
0
0
1
0
0
0
1
0
0
1
0
0
1
0
1
0
0
0
1
0
0
0
1
0
0
1
0
0
1
0
8th
Line 56→ 1
1
1
1
1
1
Line 62→ 1
Line 63→ 0
……………
page(X=7)
………
Line 15→
0
1
1
1
1
1
1
0
1
1
1
1
1
1
1
0
RAM Y address(Y0 ~Y127)
……
1 0 0
0 0 1
……
0 1 0
0 0 1
……
0 0 1
0 1 0
……
0 1 0
0 0 1
……
0 0 1
1 1 0
……
0 1 0
1 1 1
……
0 1 0
1 1 1
……
0 0 0
0 0 0
……
1 0 0
0 1 1
……
0 1 0
0 1 0
……
0 1 0
0 1 0
……
1 0 0
1 1 1
……
0 1 0
0 1 0
……
0 1 0
0 1 0
……
1 0 0
0 1 1
……
0 0 0
0 0 0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
1
0
0
0
1
1
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
1
1
0
0
1
0
0
0
0
0
0
0
Data
←DB0(LSB)
←DB1
←DB2
←DB3
←DB4
←DB5
←DB6
←DB7(MSB)
←DB0(LSB)
←DB1
←DB2
←DB3
←DB4
←DB5
←DB6
←DB7(MSB)
……
0
0
0
1
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
……
……
……
……
……
……
……
……
0
0
0
1
1
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
1
←DB0(LSB)
←DB1
←DB2
←DB3
←DB4
←DB5
←DB6
←DB7(MSB)
Page.
15 / 21
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
ADDRESS CONFIGURATION OF DISPLAY DATA RAM
0 1
DB0
X=0→ To
DB7
DB0
X=1→ To
DB7
DB0
X=2→ To
DB7
DB0
X=3→ To
DB7
DB0
X=4→ To
DB7
DB0
X=5→ To
DB7
DB0
X=6→ To
DB7
DB0
X=7→ To
DB7
2
Y address
3 ……………………126
Page0
Page1
Page2
Page3
Page4
Page5
Page6
Page7
127
Line0
To
Line7
Line8
To
Line15
Line16
To
Line23
Lint24
To
Line31
Line32
To
Line39
Line40
To
Line47
Line48
To
Line55
Line56
To
Line63
Address configuration of Display Data RAM
Feb. 24, 11
Page.
16 / 21
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
17 / 21
RELIABILITY TEST
No
Item
Conditions
Note
1.
High Temp. Operation
70℃
240 Hr
--
2.
High Temp. Storage
80℃
240 Hr
--
3.
Low Temp. Operation
-20℃
240 Hr
--
4.
Low Temp. Storage
-30℃
240 Hr
--
5.
High Temp./Humid Storage
40℃ 90%RH
240 Hr
--
6.
Thermal Shock
-20℃ ,30min
+40℃ ,30min
10 cycles
--
7.
Vibration Test
( IEC-68-2-6 )
Frequency : 10~55 Hz
Duration : 20 times, 6
min/time
Amplitude : 0.75 mm
--
--
8.
Shock
( IEC 68-2-27)
Duration : 11 mS
Acceleration : 100g
--
X, Y, Z
direction
APPEARANCE CHECK
CONDIITON OF APPEARANCE CHECK:
(1) Specimen shall be checked by eyes in distance of 30cm under 40w-fluorescence lamp.
(2) Checking direction shall be in 45 degree from perpendicular line op specimen surface.
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
18 / 21
HANDLING PRECAUTIONS
(1)Treat polarizer very carefully since it is easy to be damaged.
(2)When cleaning the display surface, use soft cloth (e.g. gauss) with a solvent (recommended
below) and wipe lightly.
◆ ethyl alcohol
◆ iso-prcolol
Do not wipe the display surface with dry or hard materials that will damage the polarizer
surface.
Do not use the following solvents:
◆ water
◆ ketone
◆ aromatics
(3)Direct current causes electro-chemical reaction with remarkable degradation of the display
quality. Give careful consideration to prevent direct current at ON/OFF timing and during
operation.
(4)Avoid strong shock and drop from the height.
(5)To prevent LCD panels from degradation, do not operate or store them exposed directly to
sunshine or high temperature/humidity.
(6)Give careful consideration to avoid electrical static discharge with causes uneven contrast.
(7)Even a small condensation on the contact pads (terminals) causes electro-chemical reaction
which makes missing row and column. Give careful attention to avoid condensation. When
assembling with zebra connector, clean the surface of the pads with alcohol and keep the air
very clean.
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
19 / 21
LCD PRODUCT QUALITY STANDARD
DISPLAY APPEARANCE
No
1.
2.
3.
Item
Criteria
(1) round type
diameter mm(a*)
no of defect*
a≦0.20
neglect
0.20<a≦0.35
5max
0.35<a
none
inclusions (black spot, white
spot, dust)
(2) linear type
length mm(l)
width mm(W)
no. of defect
na
W≦0.03
neglect
l ≦3
0.03<W≦0.08
6
3<l
0.08<W
none
1. scratch on protective film is permitted.
2. scratch on polarizer shall be as follow:
(1) round type
diameter mm(a*)
no of defect
a≦0.15
neglect
scratch
0.15<a≦0.20
2 max
0.20<a
none
(2) linear type
be judged bye 1.-(2) linear type
diameter < 1.5mm
dent
4.
bubble
5.
pin hole
6.
dot defect
7.
contrast irregularity(spot)
8.
9.
dot width
color tone and uniformity
not exceeding 0.5mm average diameter is acceptable between glass and
polarizing film
(a+b)/2 ≦ 0.15mm
maximum number: ignored
0.15<(a+b)/2≦0.20mm
maximum number:10
(a+b)/2≦0.20mm
maximum number: ignored
0.20<(a+b)/2≦0.30mm
maximum number:5
x=width
diameter spec
no of defect
a≦0.50mm
neglect
0.50<a≦0.75
5
0.75<a≦1.00
3
1.00<a
none
design width ±15%
obvious uneven color is not permitted
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
20 / 21
WARRANTY
This product has been manufactured to your company’s specifications as a part for use in
your company’s general electronic products. It is guaranteed to perform according to
delivery specifications. For any other use apart from general electronic equipment, we
cannot take responsibility if the product is used in medical devices, nuclear power control
equipment, aerospace equipment, fire and security systems, or any other applications in
which there is a direct risk to human life and where extremely high levels of reliability are
required. If the product is to be used in any of the above applications, we will need to
enter into a separate product liability agreement.
1
13 months guarantee starts from the date code.
2
We cannot accept responsibility for any defect, which may arise from additional
manufacturing of the product (including disassembly and reassembly), after product
delivery.
3
We cannot accept responsibility for any defect, which may arise after the application
of strong external force to the product.
4
We cannot accept responsibility for any defect, which may arise due to the
application of static electricity after the product has passed your company’s
acceptance inspection procedures.
5
We cannot accept responsibility for industrial property, which may arise through the
use of your product, with exception to those issues relating directly to the structure or
method of manufacturing of our product. Microtips-origin longer than one year from
Microtips production.
DIMENSIONAL OUTLINES
z
See the next page……..
Messrs.
Product Specification Model: NMTG-S12864BFYHSGY-C
Rev. No. Issued Date.
A
Feb. 24, 11
Page.
21 / 21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement