U-Line | ADA151M | Product data | U-Line ADA151M Product data

U-Line ADA151M Product data
Thomco Job # 3064
RECORD OF CONTRACTOR SUBMITTAL
TO:
So Cal Gas Co.
1801 S. Atlantic Blvd.,
Monterey Park, CA 91754
ATTN / C/O:
Submittal #: 114530-01
Date: 10/14/14
Tom Souders, So Cal Gas Co.
PROJECT: Monterey Park Learning Center
PRIORITY:
URGENT
NORMAL
FOR:
INFORMATION ONLY
AS REQUESTED
REFERENCE
YOUR FILES
SUBMITTALS FOR APPROVAL
RESPONSE REQUIRED
SENT BY:
No.
COPIES
SPECIFICATION
DATED
1
5
114530
10/14/14
2
5
114530
10/14/14
3
5
114530
10/14/14
4
5
114530
10/14/14
5
5
114530
10/14/14
6
1
114530
10/14/14
HAND DELIVER
U.S. MAIL
ELECTRONIC
FAX
OTHER
DESCRIPTION
Sub Zero QRBI-48S Side-By-Side Refrigerator
Product Data Submittal
Sub Zero QRBI-36RG Beverage Refrigerator
Product Data Submittal
Asko D5634XKLS ADA Dishwasher Product
Data Submittal
GE Profile PEB7226SF/EH 2.2 C.U. F.t.
Microwave Product Data Submittal
U-Line ULI-030 ADA151M Ice Maker Product
Data Submittal
Appliance Electronic Product Data
Submittal
REMARKS:
_____________________________________________________________________________________
PLEASE REVIEW, STAMP AND RETURN AT LEAST (3) COPIES TO THE GENERAL CONTRACTOR.
_____________________________________________________________________________________
This submittal has been reviewed for conformance to drawings and
specifications.
SIGNED:
Louis Kloss
Louis Kloss, Project Manager
COPIES TO:
A/E of Record or Designer
Thomco Project Superintendent
Thomco File: Submittal File
Owner / Construction Manager:
Subcontractor:
48" Built-In Side-by-Side
subzero.com
FEATURES
•Four design options: framed, overlay,
flush inset and stainless steel.
•Dual refrigeration system ensures the
freshest food and energy efficiency.
•Electronic microprocessor constantly
monitors entire unit to ensure proper
food storage environment.
•Air purification system reduces odors,
bacteria, viruses and ethylene gas.
•Advanced water filtration system.
•Illuminated touch control panel.
•Bright interior lighting throughout,
including storage drawer area.
•Adjustable door shelves, spill-proof
glass refrigerator shelves, dairy
compartment and wire freezer shelves.
•Crisper and deli drawers form a lowertemperature zone ideal for produce and
meats.
•Soft-close glide system on refrigerator
storage drawers.
•Easy-access flip-up grille.
•Informational freshness cards.
•Automatic ice maker with max ice
feature temporarily increases production.
•ENERGY STAR® qualified (excludes
BI-48S/O).
ACCESSORIES
MODEL OPTIONS
Overlay (framed, flush inset)
BI-48S/O
Stainless (tubular handle)
BI-48S/S/TH
Stainless (pro handle)
BI-48S/S/PH
INTERIOR FEATURES
REFRIGERATOR
•Framed front panels in white or stainless
steel.
•Flush inset panels in stainless steel with
tubular or pro handles.
4 Adjustable glass shelves
1 Stationary glass shelf
1 High-humidity drawer with divider
2 Storage drawers with divider
3 Adjustable door shelves
2 Stationary door shelves
Adjustable dairy compartment
•Custom front panel mounting kit.
FREEZER
•Stainless steel kickplate.
3 Adjustable wire shelves
1 Stationary solid shelf
3 Storage drawers
5 Adjustable door shelves
Automatic ice maker
Model BI-48S
•Grilles for 83" or 88" finished height
(84" is standard).
•Side panel in white or stainless steel.
•Stainless steel tubular and pro handles.
•Full-length standard and extended
framed handles.
•Retrofit kit for 600 series panels.
•Dozen egg container.
•Replacement air purification cartridge
and water filter.
Accessories avail­able through an authorized
Sub-Zero dealer. For local dealer information, visit the find a showroom section of our
website, subzero.com.
48" Built-In Side-by-Side
subzero.com
DIMENSIONS
SPECIFICATIONS
PRODUCT
Dimensions
Door Clearance
Weight
ELECTRICAL
26 3/16" (665)
48" (1219)
48"W x 84"H x 24"D
30 1/2"
630 lb
7"
E
(178)
6"
CAPACITY
(152)
Refrigerator
Freezer
19.1 cu ft
9.8 cu ft
75 1/2" (1918)
FROM FLOOR
84"
(2134)
RIGHT SIDE
OF OPENING
ELECTRICAL
Supply
Service
73 3/4"
115 VAC, 60 Hz
15 amp circuit
(1873)
PLUMBING
PLUMBING
Supply
Pressure
1/ 4"
OD copper, braided
stainless steel or PEX tubing
35–120 psi
RIGHT SIDE
OF OPENING
HEIGHT DIMENSIONS ± 1/2" (13)
23 7/8" (606)
4" (102)
Specifications are subject to change without
notice. Visit subzero.com/specs for the most
up-to-date information.
18" (457)
23 7/8"
3" (76)
(606)
Dimensions may vary ± 1/8" (3). Dimensions in
parentheses are millimeters unless otherwise
specified.
8 3/8"
11 5/8"
(213)
(295)
6" (152)
AREA EXTENDS 1/2" (13)
FORWARD ON FLOOR
30"
(762)
2 3/8" (60)
Dimensions based on stainless steel model. For flush inset, add 1/2" (13) to door clearance dimensions.
STANDARD INSTALLATION
FLUSH INSET INSTALLATION
26 3/16"
24" (610)
OPENING
DEPTH
(665)
FLUSH
INSET
DEPTH
2 3/16"
(56)
FINISHED
CLEATS*
TOP VIEW
TOP VIEW
11/4"
1/4"
(6)
83 3/4"
(2127)
OPENING
HEIGHT
47 1/2W
" (1206)
OPENING WIDTH
(32)
84"
(2134)
FLUSH
INSET
HEIGHT
50" W
(1270)
FLUSH INSET WIDTH
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
SIDE VIEW
NOTE: Shaded line represents profile of unit.
FRONT VIEW
SIDE VIEW
2 3/16"
(56)
FRONT VIEW
*3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
NOTE: Shaded line represents profile of unit with 3/4" (19) panel.
©Sub-Zero, Inc. all rights reserved. 6/2014
36" Built-In All Refrigerator with Glass Door
subzero.com
FEATURES
•Four design options: framed, overlay,
flush inset and stainless steel.
•Triple-pane, UV-resistant glass door—
high altitude glass available.
•Electronic microprocessor constantly
monitors entire unit to ensure proper
food storage environment.
•Air purification system reduces odors,
bacteria, viruses and ethylene gas.
•Illuminated touch control panel.
•Bright interior lighting throughout,
including storage drawer area.
•Adjustable spill-proof glass shelves.
•Crisper and deli drawers form a lowertemperature zone ideal for produce and
meats.
•Soft-close glide system on refrigerator
storage drawers.
•Easy-access flip-up grille.
•Informational freshness cards
ACCESSORIES
MODEL OPTIONS
Overlay (framed, flush inset)
BI-36RG/O
Stainless (tubular handle)
BI-36RG/S/TH
Stainless (pro handle)
BI-36RG/S/PH
Specify RH or LH door.
INTERIOR FEATURES
REFRIGERATOR
4
1
1
2
Adjustable glass shelves
Stationary glass shelf
High-humidity drawer with dividers
Storage drawers with dividers
•Grilles for 83" or 88" finished height
(84" is standard).
•Flush inset and dual flush inset panels
in stainless steel with tubular or pro
handle.
•Side panel in white or stainless steel.
•Stainless steel tubular and pro handles.
•Full-length standard and extended
framed handles.
•Stainless steel kickplate.
•Dual installation kit with or without dual
wide grille—84" finished height.
Model BI-36RG
•Retrofit kit for 600 series panels.
•Dozen egg container.
•Replacement air purification cartridge.
Accessories avail­able through an authorized
Sub-Zero dealer. For local dealer information, visit the find a showroom section of our
website, subzero.com.
36" Built-In All Refrigerator with Glass Door
subzero.com
DIMENSIONS
SPECIFICATIONS
PRODUCT
Dimensions
Door Clearance
Weight
ELECTRICAL
26 3/16" (665)
36" (914)
36"W x 84"H x 24"D
37 3/4"
430 lb
7"
E
(178)
6"
CAPACITY
(152)
Refrigerator
23.4 cu ft
84"
ELECTRICAL
Supply
Service
75 1/2" (1918)
FROM FLOOR
(2134)
73 3/4"
115 VAC, 60 Hz
15 amp circuit
RIGHT SIDE
OF OPENING
(1873)
Specifications are subject to change without
notice. Visit subzero.com/specs for the most
up-to-date information.
Dimensions may vary ± 1/8" (3). Dimensions in
parentheses are millimeters unless otherwise
specified.
HEIGHT DIMENSIONS ± 1/2" (13)
4" (102)
23 7/8" (606)
23 7/8"
(606)
14 1/8"
(359)
37 1/4"
(946)
2 3/8" (60)
Dimensions based on stainless steel model. For flush inset, add 1/2" (13) to door clearance dimensions.
STANDARD INSTALLATION
FLUSH INSET INSTALLATION
26 3/16"
24" (610)
OPENING
DEPTH
(665)
FLUSH
INSET
DEPTH
2 3/16"
(56)
FINISHED
CLEATS*
TOP VIEW
TOP VIEW
11/4"
1/4"
(6)
83 3/4"
(2127)
OPENING
HEIGHT
351/W
2" (902)
OPENING WIDTH
(32)
84"
(2134)
FLUSH
INSET
HEIGHT
38"W
(965)
FLUSH INSET WIDTH
11/4"
(32)
4" (102)
3"
(76)*
TYPICAL
SIDE VIEW
NOTE: Shaded line represents profile of unit.
FRONT VIEW
SIDE VIEW
2 3/16"
(56)
FRONT VIEW
*3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.
NOTE: Shaded line represents profile of unit with 3/4" (19) panel.
©Sub-Zero, Inc. all rights reserved. 9/2014
D5634XLHS/TH Tubular handle
Features
PROGRAMS
Heavy wash
Delicate wash
Quick wash
Super quick
Eco wash
Rinse and dry
Rinse and hold
OPTIONS
Product overview
Product:Dishwasher
Size:XL
Mode of installation:Built-in
Energy class:A++
Product:Built-in dishwasher
Dimensions of the product (W×H×D):24” × 32 1/4” × 22 7/8” (610 × 819 × 581
mm)
Delayed start: 24 h
High temperature
Long dry
CLEANING SYSTEMS
Self cleaning filters
AquaLevel™ Sensor
DRYING SYSTEM
Specifications
Turbo Drying™
GENERAL
COMFORT/EASY OF USE
Display type:LED display
Number of programs:9
Noise level:48 dB(A)
Number of baskets:2
Max loading height upper basket:9 1/16 (230 mm)
Max loading height lower basket:12 3/16 (310 mm)
Fault indication
Rinse-aid indication
Time remaining indicator
DIMENSIONS AND INSTALLATION
Height:32 1/4 (819 mm)
Width:24 (610 mm)
Depth:22 7/8 (581 mm)
Length inlet hose:66 1/8 (1680 mm)
Length outlet hose:41 3/4 (1060 mm)
Cord length:46 7/16 (1180 mm)
Weight net:108 lbs
Weight gross:112 lbs
SAFETY
AquaSafe™
SteamSafe™
KidLock™ - lock the door
BASKETS
Upper: Premium
Lower: Exclusive
TECHNICAL INFORMATION
Connection rating:1300 W
Current:15 A
Voltage:120 V
CONSUMPTION
Wash performance:A
Estimated yearly energy consumption:231 kWh
Energy consumption/cycle:1,07 kWh
ASKO Appliances North America - PO Box 44848 - MADISON WI 53744
Customer Support: CALL US TOLL FREE AT 800-898-1879
DISHWASHER
INSTALLATION INSTRUCTIONS
T!tions before installing
N
A
T
R
O
IMP f these instruc
ll o
Read a
washer.
h
is
d
the
AUTOMATIC HIGH LOOP
The drain hose is fastened to the back of the machine
at the best height. To eliminate potential drain problems,
leave this hose in place.
CONTENTS
INTRODUCTION2
WHAT YOU NEED
2
3
XXL DISHWASHERS
UNIT DIMENSIONS
PREPARING THE LOCATION
3
3
ADA AND XL DISHWASHERS
4
4
4
UNIT DIMENSIONS
PREPARING THE LOCATION
CORNER INSTALLATION
EASYINSTALL CONNECTIONS
WATER SUPPLY
DRAIN CONNECTIONS
ELECTRICAL CONNECTIONS
PREPARING THE DISHWASHER FOR INSTALLATION
MOVING THE MACHINE INTO PLACE
CONNECTING THE ELECTRIC CABLE
CONNECTING THE WATER SUPPLY
FASTENING THE DISHWASHER TO THE CABINET
INSTALLING THE TOE KICK
INSTALLATION CHECKLIST
5
5
6
7
8
9
9
11
11
12
12
16
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
461328 Install DW90 USA EN Rev 01.indd 1
2014-01-16 10:25:52
Introduction
Read these instructions carefully and completely before
you install the machine. The installation should be
carried out by a qualified person who is familiar with all
local codes and ordinances for electrical and plumbing
connections.
has to be done before you move the machine into place.
If a dishwasher is being installed in this area for the first
time, most of the cabinet work, plumbing, and electrical
NOTE:
Cosmetic damage must be reported to the ASKO dealer
within five days from the date of purchase. As soon as
you unpack the dishwasher, thoroughly check it for
cosmetic damage.
If you are replacing an old dishwasher, you must check
the plumbing connection and wiring before you move
the new dishwasher into place.
what you need
TOOLS
1)
Phillips No. 2 screwdriver
2)
Flat blade screwdriver
3)
Torx screwdriver size T 20
4)
Adjustable wrenches (if you use copper fittings)
5)
Open-ended wrench
(1/2˝ [12 mm], 5/8˝ [16 mm] and 1˝ [24 mm])
6)
Tape measure
7)
Spirit level
8)
Electric drill with 1-1/2˝ drill bit
9)
Keyhole saw
MATERIALS SUPPLIED
4
*
*
5
*
*
6
8
3
2
2x
2x
1"
(25 mm)
*
1
*
7
9
4x / 3x
* Only select models.
MATERIALS
• Minimum 3/8˝ OD copper tubing of sufficient length
for your installation
• Shut-off valve and fittings for water supply line
The dishwasher is shipped with the high loop drain
hose, inlet hose and electrical cord attached and ready
to be connected. Please do not remove the high loop
connection for the drain line.
Tip Guards (optional)
When it is not possible to attach the dishwasher to the
cabinet or the underside of the counter top, you should
install tip guards to prevent the machine from tipping
when you open the door. Sold individually.
Tip Guards
(P/N 8070851)
Page 2
461328 Install DW90 USA EN Rev 01.indd 2
Customer Care Center
1-800-898-1879
www.askona.com
2014-01-16 10:25:53
XXL DISHWASHERS
D5434XXL W/B/S, D5624XXLS, D5634XXLHS, D5654XXLHS, D5894XXLHS, D5894AXXLHS
UNIT DIMENSIONS
U.S.
Metric
Technical Data
Height (Adjustable)*
34-3/8˝ to 36-1/2˝
873 mm to 927 mm
Electricity
120V, 60Hz, 15 amp
Width
24˝
610 mm
Water pressure
Depth (Includes high loop)
22-7/8˝
581 mm
DepthW/handle
24-7/8˝
(D5634XXLHS, D5654XXLHS,
D5894XXLHS)
632 mm
4.2 - 140 psi,
0.03-1.0 MPa,
0.3-10 Bar
Heating element
1200 watt
Depth W/Door Open
49-1/2˝
1257 mm
Max loading
1300 watt
Weight
110 Ib
50 kg
* Total height can be reduced by 1/2˝ (13 mm) by removing upper trim, and lowering side trim (2).
49-1/2"
1257 mm
24-7/8"; 632 mm
D5634XXLHS, D5654XXLHS, D5894XXLHS
22-7/8"
581 mm
5-3/8" to 7-3/8"
137 mm to 187 mm
*34-3/8" to 36-1/2"
*873 mm to 927 mm
24"
610 mm
2-7/8"
73 mm
Door
3-3/8"
86 mm
2"
50 mm
9"
229 mm
PREPARING THE LOCATION
Width
24˝
610 mm
Depth
24˝
610 mm
The best place for your dishwasher is in the kitchen near
the sink. This makes it easier to connect the water and
drain supply lines.
A built-in dishwasher must be enclosed on the top, both
sides and the back.
The electrical and water supplies should enter through
the area indicated by the shading on the illustration at
right. Preferably, they should come through the right side
of the machine. The access hole must be round and
smooth and no bigger than 1-1/2˝ (38 mm) in diameter. If
the partition is metal, it needs to be covered with an edge
protector. Use caution when the appliance is installed
or removed, to reduce the likelihood of damage to the
power-supply cord.
Customer Care Center
1-800-898-1879
www.askona.com
461328 Install DW90 USA EN Rev 01.indd 3
5-3/8"
136 mm
61 24"
0
m
m
The power-supply receptacle for the appliance shall
be installed in a cabinet or on a wall adjacent to the
undercounter space in whitch the appliance is to be
installed.
873-927 mm
Metric
873 to 927 mm
34-3/8" to 36-1/2" minimum
U.S.
34-3/8˝ to 36-1/2˝
Height
10 4" 51 2"
2
m
m
m
m
Cutout Dimensions
24"
610 mm
Page 3
2014-01-16 10:25:54
ADA AND XL DISHWASHERS
D5424ADA W/B/S, D5634ADAHS, D5424XL W/B/S, D5624XLCS, D5434XL W/B/S, D5454XL
S, D5634XLHS, D5638XLHS, D5644XLCS
UNIT DIMENSIONS
U.S.
Metric
Technical Data
Height (Adjustable)*
32-1/4˝ to 34˝
819 mm to 864 mm
Electricity
120V, 60Hz, 15 amp
Width
24˝
610 mm
Water pressure
Depth (Includes high loop)
22-7/8˝
581 mm
DepthW/handle
(D5634ADAHS, D5624XLCS,
D5634XLHS, D5638XLHS,
D5644XLCS)
24-7/8˝
632 mm
4.2 - 140 psi,
0.03-1.0 MPa,
0.3-10 Bar
Heating element
1200 watt
Max loading
1300 watt
Depth W/Door Open
48-3/8˝
1229 mm
Weight
108 Ib
49 kg
* 32-1/4˝ (819 mm) height requires removal of top trim, and lowering side trim (2).
48-3/8"
1229 mm
24-7/8"; 632 mm
DepthW/handle
24"
610 mm
5-3/8" to 8-1/8"
137 mm to 206 mm
32-1/4"* to 34"
819* mm to 864 mm
22-7/8"; 581 mm
2-7/8"
73 mm
Door
3-3/8"
86 mm
2"
50 mm
9"
229 mm
PREPARING THE LOCATION
Height
*32-1/4˝ to 34˝
819 to 864 mm
Width
24˝
610 mm
Depth
24˝
610 mm
The best place for your dishwasher is in the kitchen near
the sink. This makes it easier to connect the water and
drain supply lines.
A built-in dishwasher must be enclosed on the top, both
sides and the back.
5-3/8"
136 mm
The electrical and water supplies should enter through
the area indicated by the shading on the illustration at
right. Preferably, they should come through the right side
of the machine. The access hole must be round and
smooth and no bigger than 1-1/2˝ (38 mm) in diameter. If
the partition is metal, it needs to be covered with an edge
protector. Use caution when the appliance is installed
or removed, to reduce the likelihood of damage to the
power-supply cord.
Page 4
461328 Install DW90 USA EN Rev 01.indd 4
61 24"
0
m
m
The power-supply receptacle for the appliance shall
be installed in a cabinet or on a wall adjacent to the
undercounter space in whitch the appliance is to be
installed.
*819-864 mm
Metric
*32-1/4" to 34" minimum
U.S.
10 4" 51 2"
2
m
m
m
m
Cutout Dimensions
24"
610 mm
* 32-1/4˝ (819 mm) height requires removal of top trim, and
lowering side trim (2).
Customer Care Center
1-800-898-1879
www.askona.com
2014-01-16 10:25:55
CORNER INSTALLATION
If the dishwasher is installed in a corner, there must be
a minimum clearance of 2˝ (50 mm) from the side wall
so the door can open.
2˝ clearance
EASYINSTALL CONNECTIONS
PEX tubing with 3/8˝ compression fitting
PEX tubing has a 95-year spec life.
Fits American dishwasher water
supply valves. Be sure to install the
O-Ring which is attached to the PEX
tubing in a plastic bag.
Drain hose boot
Ready to be cut to desired
drain connection. Only
one clamp required.
Electrical cord
120 volts, 15 amp cord is supplied with
the dishwasher.
WARNING!
Do not use an extension cord for this appliance.
Customer Care Center
1-800-898-1879
www.askona.com
461328 Install DW90 USA EN Rev 01.indd 5
Page 5
2014-01-16 10:25:56
WATER SUPPLY
WARNING!
Plumbing connections must comply with applicable
sanitary, safety and plumbing codes in your area.
The machine can be connected to either a hot (max. 160
°F, 70 °C) or cold water supply. We recommend a cold
water supply. The water pressure should be 4.2-140 psi.
WARNING!
In order to prevent heat damage to the inlet valve, all
solder connections must be made before the water
line is connected to the dishwasher.
Connect to cold water...
If you use oil or electricity to heat your home.
Connect to hot water (max 160 °F, 70 °C)...
If you use district heating, solar power, or geothermal
power to heat your home. Choosing a hot water
connection cuts program times and reduces the
dishwasher’s electricity consumption.
The dishwasher comes with a 6-foot PEX water supply
line that has a 3/8˝ NPT female connection.
After determining where the water supply line will enter
under the sink, drill a 1-1/2˝ (38 mm) access hole and
run the line to the approximate inlet valve location shown
in the figure below. The water line inlet valve is on the
right rear of the machine.
For service convenience, a shut-off valve (not supplied)
should be installed in the supply line in an easily
accessible location, such as, beneath the sink.
1. Water supply
2. Water supply valve to dishwasher (not supplied)
NOTE:
Be sure to run the PEX tubing through the hole to the
sink compartment before moving the dishwasher into
position.
It is important that the water supply line and the shut off
valve have a sufficient flow volume. At least 3 gallons
(12 liters) per minute must be able to pass through the
line. The water pressure should be 4.2-140 psi.
Page 6
461328 Install DW90 USA EN Rev 01.indd 6
Customer Care Center
1-800-898-1879
www.askona.com
2014-01-16 10:25:56
DRAIN CONNECTIONS
ASKO provides a 7/8˝ (22 mm) diameter corrugated
drain hose which is connected to the back of the unit to
form a high loop.
NOTE:
Do not use any fittings anywhere in the drain
line that are less than 7/8˝ (22 mm) OD.
THREE WAYS TO INSTALL
DRAIN CONNECTIONS
A) Typical connection to sink plumbing before
trap (high loop drain)
The access hole for the drain line should be 1-5/8˝ (41 mm)2˝ (50mm) max.
The end of the drain line is 1/2˝ (12 mm), but it is adjustable
to 7/8˝, 3/4˝, 5/8˝ (22 mm, 19 mm, and 16 mm). If the drain
connection is larger than
1/2˝ (12 mm), you can
easily cut the drain line to
fit the connection.
508
The illustrations to the right show three ways to connect
the drain supply line.
THE HIGH LOOP
The high loop is necessary for proper draining. Therefore,
all ASKO dishwashers have the drain hoses attached to
the drain pump and fastened to the top back of the unit,
as illustrated. This gives the drain
hose an automatic high loop, which
is necessary for proper draining. The
drain hose is fastened at the best
high loop height.
B) Connection to air gap then to the trap
To eliminate potential drain problems, simply leave this
hose in place.
508
DO NOT REMOVE THE HIGH LOOP ATTACHED TO
THE BACK OF THE DISHWASHER!
IMPORTANT THINGS TO REMEMBER:
♦ Failure to provide the proper drain connection height
(minimum of 20˝ (508 mm) above the bottom of the
dishwasher base) or a 20˝ (508 mm) high loop will
result in improper drainage, which will damage the
machine.
♦ No part of the drain hose should be higher than 35˝
(889 mm) from the bottom of the dishwasher.
♦ The drain hose can be extended to a maximum length
of 10 feet (3048 mm). Joints and jointed tubes, if any,
must have a minimum 7/8˝ (22 mm) OD.
♦ If the drain line is going to be connected to a waste
disposer, be sure to remove the knockout or plug
from the fitting on the disposer before connecting
the drain line.
♦ Do not use fittings smaller than 7/8˝ (22 mm) OD;
otherwise the water may not drain properly.
When the installation is ready, open the supply valve to
pressurize the fill system. Then check that all connections
are tight and there are no leaks.
C) Connection to waste disposer with air gap
508
NOTE:
Don’t forget to remove the knockout or plug from the
disposer fitting.
Customer Care Center
1-800-898-1879
www.askona.com
461328 Install DW90 USA EN Rev 01.indd 7
Page 7
2014-01-16 10:25:56
ELECTRICAL connections
WARNING!
Before working on wiring for any electrical appliance,
be sure the electrical power has been turned off at
the breaker/fuse box.
WARNING!
Do not use an extension cord for this appliance.
WARNING!
Disconnect the electrical power supply and place a
tag at the disconnect switch indicating that you are
working on the circuit.
WARNING!
7
185
Electrical and grounding connections must comply
with the applicable portions of the national electrical
code and/or other local electrical codes.
NOTE:
Access holes should be 1-1/2˝ (38 mm) in diameter
with no sharp edges.
The dishwasher comes with an electrical
cord for 120 volts, 15 amp supplied. This
cord should be plugged into the 120 volt
outlet under the sink.
If the cord is not long enough, or if a hard-wire installation
is needed, follow instructions on page 11.
PERMANENTLY-CONNECTED APPLIANCE
Grounding instructions
This unit must be grounded to operate properly. It must
be connected to a grounded metal, permanent wiring
system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to the
equipment-grounding terminal or lead of the appliance.
Damage to the dishwasher could occur if it is not properly
grounded.
WARNING!
Make sure the water supply line, drain line and branch
circuit wiring do not touch any exposed terminals of
dishwasher wiring.
CORD-CONNECTED APPLIANCE
Grounding instructions
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance
for electric current. This appliance is equipped with a
cord having an equipment-grouding conductor and
a grounding plug. The plug must be plugged into
an appropriate outlet that is installed and grouded in
accordance with all local codes and ordinances.
WARNING!
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrican or service representative
if you are in doubt whether the appliance is properly
grounded. Do not modify the plug provided with the
appliance, if it will not fit the outlet, have proper outlet
installed by a qualified electrician.
Page 8
461328 Install DW90 USA EN Rev 01.indd 8
Customer Care Center
1-800-898-1879
www.askona.com
2014-01-16 10:25:57
PREPARING THE DISHWASHER FOR INSTALLATION
At this point the styrofoam, plastic wrap, and the wood
pallet (base) should be removed from the dishwasher.
Now is an excellent time to inspect for any shipping
damage. Should you find any damage, you should report
it to your dealer or builder immediately.
Be sure to remove the toe kick and toe kick insulation
(only on certain models) from the top of the dishwasher.
Attach the supplied door sealing
(Only certain models.)
This strip is an essential part of the Turbo Dry Express
system and must be installed to ensure an optimum
seal between the dishwasher tank and door.
1
SLIDES FOR LEGS
(Only certain models.)
The unit comes with white plastic slides for the legs to
protect the kitchen floor from being damaged when
you slide the unit into place. The
slides simply snap onto the bottom
of the legs.
Use caution when sliding the
dishwasher into place. The protective slides could cause damage to
certain types of soft flooring.
3
2
1
Attach the light shielding film
(Only certain models.)
Attach the light shielding film (packed in the document
bag) to the underside of the countertop above the touch
buttons.
2
NOTE:
The surface on which the protective film is to be attached
must be clean and dry.
Moving the machine into place
WARNING!
Make sure you put the protective slides on the legs
to prevent damaging the floor when you slide the unit
into place (see page 9).
As you do this, feed the drain line and inlet hose into the
access hole(s) in the side of the cabinet. Use caution
when sliding the dishwasher into place. The protective
slides could cause damage to certain types of soft
flooring.
WARNING!
Be careful of sharp edges.
Customer Care Center
1-800-898-1879
www.askona.com
461328 Install DW90 USA EN Rev 01.indd 9
Page 9
2014-01-16 10:25:59
Moving the machine into place
Rear foot
Front feet
1˝ (24 mm)
1˝ (24 mm)
Adjusting machines with three or
four feet
Adjusting machines with FRONT
ADJUSTABLE REAR Foot
1. Position the machine in front of the cabinet opening.
1. Position the machine in front of the cabinet opening.
2. Push the plastic feet into place on all steel feet
(included in document bag). (Only certain models.)
2. Push the plastic feet into place on all steel feet
(included in document bag). (Only certain models.)
3. Start by measuring the height from the floor to the
bottom edge of the counter top. Measure the height
from the floor to the top edge of the dishwasher.
3. Start by measuring the height from the floor to the
bottom edge of the counter top. Measure the height
from the floor to the top edge of the dishwasher.
4. Loosen the lock nuts on the dishwasher’s steel feet
using a 5/8˝ (16 mm) open-ended wrench. Screw the
lock nuts down as close to the floor as possible.
4. Loosen the lock nuts on the dishwasher’s front steel
feet using a 5/8˝ (16 mm) open-ended wrench. Screw
the lock nuts down as close to the floor as possible.
5. Make the height adjustment while the dishwasher is
in front of the opening. Adjust all feet by turning them
clockwise to raise or counterclockwise to lower the
dishwasher.
5. Lean the dishwasher forwards a little and roughly
adjust the rear foot by turning the adjustment screw
at the front clockwise to raise and counterclockwise
to lower the dishwasher (see illustration above). Use
a flat-bladed screwdriver or a 1/4˝ nut driver.
6. Check that the height of the machine corresponds
to the height from the floor to the bottom edge of the
counter top.
7. Tighten the lock nuts (lock nut) on the rear feet (foot).
8. Pull out the drain hose to ensure there are no sharp
bends.
9. Start to feed water and drain lines and electric cord
(if necessary) into the access hole(s) in the cabinet.
10.Gently slide the unit into the dishwasher opening. As
you do this, feed the drain line and inlet hose into the
access hole(s) in the side of the cabinet.
11.If installing in a metal cabinet, the hole(s) for the drain
hose and connection pipe must be fitted with edge
protectors/rubber grommets.
12.Place the spirit level on the dishwasher door to check
that the machine is level and adjust if necessary. The
door must be fully closed!
13.Make any final adjustments to the front feet. (The
machine may have an inclination of 3/16˝ (5 mm)
maximum without affecting its performance.)
14.When the front feet are properly adjusted, tighten the
lock nuts to the base pan.
Page 10
461328 Install DW90 USA EN Rev 01.indd 10
6. Adjust the front feet by turning them clockwise to
raise or counterclockwise to lower the dishwasher.
7. Check that the height of the machine corresponds
to the height from the floor to the bottom edge of the
counter top.
8. Pull out the drain hose to ensure there are no sharp
bends.
9. Start to feed water and drain lines and electric cord
(if necessary) into the access hole(s) in the cabinet.
10.Gently slide the unit into the dishwasher opening. As
you do this, feed the drain line and inlet hose into the
access hole(s) in the side of the cabinet.
11.If installing in a metal cabinet, the hole(s) for the drain
hose and connection pipe must be fitted with edge
protectors/rubber grommets.
12.Place the spirit level on the dishwasher door to check
that the machine is level and adjust if necessary. The
door must be fully closed!
13.Make any final adjustments to the feet. (The machine
may have an inclination of 3/16˝ (5 mm) maximum
without affecting its performance.)
14.When the feet are properly adjusted, tighten the lock
nuts on the front feet to the base pan.
Customer Care Center
1-800-898-1879
www.askona.com
2014-01-16 10:26:01
CONNECTING THE ELECTRIC CABLE
If the cord is not long enough, or if a hard-wire installation
is needed, follow the steps below to complete the
electrical connection.
4. Connect ground wire to ground connection screw
on the bottom.
WARNING!
Before starting this procedure, be sure the power is
turned off at the breaker/fuse box.
1. Connect supply cable with
a UL-listed strain relief
bushing (if nonmetallic
cable is to be used).
2. Connect branch circuit
white lead to N lead on
filter.
NOTE:
When doing a hard-wire installation, you must remove
the supplied power cord.
3. Connect branch circuit
black lead to L lead on filter.
CONNECTING THE WATER SUPPLY
In order to prevent heat damage to the inlet valve, all
solder connections must be made before the water
supply line is connected.
Flush the water supply line prior to connecting it to the
water fill tube.
The unit has a float switch in the base pan to protect
against flooding. If the inlet valve connection is not
seated properly, water may leak into the base pan and
activate the float switch.
Water connection should be carried out by a qualified
professional. It is important that the water supply line
and the shut-off valve have a sufficient flow volume. At
least 3 gallons (12 liters) per minute must be able to
pass through the line. Connect the machine using the
accompanying supply hose. Water pressure should be
4.2-140 PSI. There should be a shut off valve on the
water pipe.
If the pipes are newly installed, it may be wise to flush
them through so that any debris is washed away.
Otherwise, debris can clog the filter in the machine’s
water intake and cut off the water supply.
Only use the inlet hose supplied with the machine. Do
not reuse old or other loose inlet hoses.
Use the supplied O ring and tighten the connection by
hand plus a quarter turn with a wrench.
1. Water supply
2. Water supply valve to dishwasher (not supplied)
NOTE:
Be sure to run the PEX tubing through the hole leading
to the sink compartment before moving the dishwasher
into position.
TESTING for leaks
1. Turn on the water supply and check for leaks.
2. Turn the power on at breaker/fuse box and test the
dishwasher operation by running a Rinse & Hold
cycle. (This should take about six minutes.)
3. Turn off the electrical power and check for leaks
under the dishwasher and sink.
4. Make sure that no kinks have developed in the drain
lines.
If there are no leaks and the dishwasher seems to
be working properly, continue with the installation.
Customer Care Center
1-800-898-1879
www.askona.com
461328 Install DW90 USA EN Rev 01.indd 11
Page 11
2014-01-16 10:26:01
FastenING the dishwasher to the cabinet
It’s necessary to fasten the dishwasher to the cabinet
so it won’t tilt when the door is opened or if something
heavy is placed on the door. Use only the stainless steel
screws provided with the machine.
1
1. Use option A for U.S. or European
standard installations.
Use option
3
B only for European standard
installations, or U.S. installations
2
where there is a hard counter-top such
as tile or marble.
4x / 3x
2. When the machine is properly
attached, check that the feet are tight
against the floor and that the machine
is level.
4
2x
5
2x
NOTE:
When it is not possible to attach the dishwasher to the
cabinet or the underside of the counter top, you should
install tip guards to prevent the machine from tipping
when you open the door. Sold individually.
1"
(25 mm)
NOTE:
Be sure to use white spacers to keep from over-tightening
the mounting screws.
Tip Guards
(P/N 8070851)
INSTALLING THE TOE KICK
?
6
7
Type A
See page 13
Page 12
461328 Install DW90 USA EN Rev 01.indd 12
Type B
See page 14
Customer Care Center
1-800-898-1879
www.askona.com
2014-01-16 10:26:02
INSTALLING THE TOE KICK
type A
?
8
9
Insulation material
Insulation material
1.
1.
2. The toe kick is attached with two screws that can
only be adjusted vertically.
2.
3. The toe kick is attached with two screws that can
only be adjusted vertically.
NOTE:
or
NOTE:
or
Customer Care Center
1-800-898-1879
www.askona.com
461328 Install DW90 USA EN Rev 01.indd 13
Page 13
2014-01-16 10:26:05
INSTALLING THE TOE KICK
type B
?
8
9
Insulation material
Insulation material
1.
1.
2.
2.
3.
Page 14
461328 Install DW90 USA EN Rev 01.indd 14
Customer Care Center
1-800-898-1879
www.askona.com
2014-01-16 10:26:07
INSTALLING THE TOE KICK
4.
5.
x
x
6.
Customer Care Center
1-800-898-1879
www.askona.com
461328 Install DW90 USA EN Rev 01.indd 15
Page 15
2014-01-16 10:26:09
INSTALLATION CHECKLIST
Asko - Dishwasher
Appliance Installation Checklist
• Remove packaging and check for cosmetic damages.
• Remove the information packets from inside the dishwasher.
• Attach any accessories as required by the installation. Fill strips, light shielding
film, supplied door sealing...
• Attach the drain line using the largest section of the disposer boot allowable.
Leave the high loop in place.
• Attach the PEX fill hose. Don’t forget to use the O-ring.
• Plug the dishwasher into the wall.
• Turn on the water and check the fill line connections for leaks.
• Slide the unit into the cabinet and level the machine front to rear, and left to right.
• Mount the unit to the cabinet.
•
Turn the power to the unit on and start a cycle. Make sure there are no drain
leaks.
• Show the customer their warranty card, and help them locate the model and
serial number on the unit.
• Leave all user books for consumer.
Page 16
461328 Install DW90 USA EN Rev 01.indd 16
Art. No 461328 Rev. 01
Customer Care Center
1-800-898-1879
www.askona.com
2014-01-16 10:26:09
PEB7226SF/EH
GE Profile™ Series 2.2 Cu. Ft. Countertop Microwave Oven
Dimensions and Installation Information (in inches)
Exterior Dimensions (in inches)
W x H x D
25-1/2" ± 1/8"
24-1/8 x 14 x 19-3/4
Optional Accessory Trim Kits for GE Microwave Ovens
(Available at additional cost)
For a custom built-in appearance, these kits allow built-in
installation of the countertop microwave oven into a wall or
cabinet alone and are U.L. approved for installation over a
GE single electric wall oven. These kits should not be installed
over a gas wall oven.
Accessory trim kits
"Z"
Max Height
Trim Kits
30" Deluxe
29-3/4"
19-1/8"
JX7230SFSS
27" Deluxe
26-3/4"
19-1/8"
JX7227SFSS
Note: 120V, 60-cycle, grounded power receptacle location
optional on back within cabinet opening.
A
16-3/4" ± 1/8"
C
B
19-1/8"
Trim
Kit
Installation Information: This information is not intended to
be used for installing unit described. Before installing, consult
installation instructions packed with product/kit for current
dimensional data.
22" MIN.
receptacle
in cabinet
19-1/2" MIN.
receptacle
outside
cabinet
Bra
cke
t
36" MIN.*
Z
Cabinet overlap requirements
30"
27"
A - Overlap of trim kit over top of cabinet
1"
1"
B - Overlap of trim kit over bottom of cabinet 1-3/8" 1-3/8"
C - Overlap of trim kit over sides of cabinet 2-1/8" 5/8"
*For ADA compliance, the microwave must be
installed no higher than 36-1/4".
Accessory Trim Kits
™
JX7230
For answers to your Monogram,® Cafe
Series
™
or Profile Series appliance questions,
visit
JX7227
our website at geappliances.com or call GE
Answer Center® service, 800.626.2000.
Note:
Allow an additional inch
of clearance beyond trim
frame on all sides
Listed by
Underwriters
Laboratories
Z
29-3/4"
26-3/4"
Specification Revised 5/14
240379
PEB7226SF/EH
GE Profile™ Series 2.2 Cu. Ft. Countertop Microwave Oven
Features and Benefits
• 2.2 cu. ft. capacity - 1100 watts (IEC-705 test procedure)
• Sensor cooking controls - Automatically adjusts time and power
• Optional built-in trim kit - Custom appearance and built-in
convenience
• Weight and time defrost - Simply enter the weight of the food,
and the oven automatically sets the optimal defrosting time and
power level or set your desired time for defrosting
• Extra-large 16" turntable - Rotates food throughout the cycle and
accommodates large cookware
• Instant on controls - One-touch instant operation
• Control lockout - Helps prevent accidental activation
• Add 30 seconds - Add 30 seconds of microwave cooking time
• Kitchen timer - Minute timer helps keep you on track
• Model PEB7226SFSS – Stainless steel
• Model PEB7226EHES - Slate
PEB7226SF
Listed by
Underwriters
Laboratories
Specification Revised 5/14
240379
1A0D7A5 1W
5 1CMS
ADA151M
Stainless
Black
ADA S e ri e s
PERFORMANCE
• Daily ice rate of up to 25 lbs of crescent ice
• Stores up to 25 lbs of ice
• Uses less than 3 gallons of water to produce 25 lbs of ice, conserving both energy
and water
• Uses less energy than a 75 watt light bulb
• Perfect size crescent ice cubes (1/2"W x 3/4"H x 2-1/2"L)
• Mechanical control monitors ice making operation to ensure maximum daily ice
production
• Manual defrost
• UL residential and commercial listings
Interior / Exterior
• 32" height meets ADA height requirement
• No drain required, easy and inexpensive to install and requires only a 1/4" outside
diameter water line
• Stainless steel wrap door with black end caps on stainless model must be ordered
left or right hand hinged
• Black door model is field reversible
• Standard commercial stainless steel handle is interchangeable with professional
handle option on stainless steel model
• Black vinyl clad textured cabinet is more resistant to scratching, peeling and flaking INTEGRATION
ICE MAKERS
FEATURES
• Unit can be built-in or freestanding providing a custom aesthetic
• Black model will accept a 1/4" insert panel to match with surrounding decor
• Allow a 2-1/2" clearance on hinged side for 90° door opening when installed
adjacent to a wall (for stainless steel model)
• Allow 1/4" width overall for proper installation (see back side for details)
• No additional clearance around sides, top or rear of unit is needed for ventilation
• Durable, factory installed leveling legs provide a more precise undercounter fit
• Do not obstruct front grille air flow
No ice shortages here.
Produces up to 25 pounds
of crescent ice (1/2" W x
3/4" H 2-1/2" L) per day.
No drain required.
8900 North 55th Street Milwaukee, Wisconsin 53223 414.354.0300 Fax 414.354.7905 u-line.com
7 51 B
V
A1D0 A
5 1E M
23"*
32"
15"
*Add 3/4” To Depth For Water Line Clearance
23"*
23-3/4"
Minimum
32"
to
33"
4"
1-3/4"*
W
E
32"
3-9/16"*
1-7/8"*
15-1/4"
*Can Vary Up To +1” Depending On Height Of Leveler Legs
Legend: E - Electrical W - Water
15"
*Add 3/4” To Stainless
Depth For Water Line
Clearance
ADA151MS
Model
and
ADA151MB Black Model
* Add 3/4" for water line clearance
DIMENSIONS AND SPECIFICATIONS
ICE MAKERS
Overall Dimensions
ADA15IM
Height Width
Depth – black model
With stainless steel handle
32" (81.2)
15" (38.1)
23" (69)
24-7/8" (63)
Shipping weight
86 lbs (39 kg)
Running amps
Maximum start-up amps
Amps pertain to voltage rating
2.5
18.0
110/115 volt, 60 Hz
Capacities:
Approximate daily ice production
Ice storage
Manual defrost
Up to 25 lbs
Up to 25 lbs
Stainless Right-hand
U-ADA15IMS-00
Stainless Left-hand
U-ADA15IMS-01
Black
U-ADA15IMB-00
Optional in 220/230 voltage, 50/60 Hz
On the 220/230 volt models, amps are decreased by
approximately 50 percent.
Please visit www.u-line.com for installation guide.
All specifications are subject to change without notice.
8900 North 55th Street Milwaukee, Wisconsin 53223 414.354.7905
414.354.0300 Fax 414.354.7905 u-line.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising