Mitel 5360 User guide

Mitel 5360 User guide
MITEL
5360
IP Phone User Guide
5360 IP Phone Quick Reference Guide
This guide provides information for frequently used
features. For more information about these and other
features, refer to the user guide. For voice mail
information, refer to the voice mail user guide for your
system.
Feature Buttons
Commonly Used Feature Codes
Contact your system administrator for more information
about system features.
Feature
Code
ACD Agent – Log In/Out
328
Most of the following feature codes work when your IP
phone is idle. However, if you are on an active call or if
the IP phone is off-hook, you may need to press
(Special) to activate the feature before you enter the
feature code.
Automatic IC Call Access – On/Off
361
Automatic Trunk Call Access – On/Off
360
Background Music – On/Off
313
Call Forward – All Calls
355
If you make a mistake when entering numbers or
characters, you can press
(Hold) to move the
cursor to the left and delete the characters entered, or
you can press * to cancel the feature.
Call Logging
333
Conference
5
Button
Action
Default Station
394
Directory
307
Display Time And Date
300
(Up)
Provides volume control.
Do-Not-Disturb – On/Off
372
(Down)
Scrolls through feature options.
Dynamic Extension Express – On/Off
364
Activates Handsfree Mode.
Dynamic Extension Express Handoff
388
Activates features.
Handsfree – On/Off
319
(Mute)
Mutes the microphone during a
call.
Headset – On/Off
317
(Applications)
Activates the Applications menu
to use the conference unit or
cordless devices, program
various phone settings, and
enable Clean Mode.
Hold – Individual
336
(Speaker)
Activates features while on a
call.
(Special)
(Redial)
(Hold)
(Transfer)
(Message)
The
(Special) button does
not cancel features. To cancel
features, press the Star button
(*).
Calls the last external number
dialed. You cannot redial
internal numbers.
Hold – System
335
Hunt Group – Remove/Replace
324
Message – Cancel Left Message
366
Message – Delete Message
368
Message – Leave Message
367
Message – View Messages Menu
365
Microphone Mute – On/Off
314
Page Receive – On/Off
325
Program Buttons
397
Program Station Password
392
Programmable Buttons – Default
395
Places the current call on hold.
Queue (Callback) Request
Left/Backspace when entering
dialpad characters.
Record-A-Call
Transfers the current call.
Ring Tone Selection
398
Right/Forward when entering
dialpad characters.
Station Speed Dial
382
Station Speed Dial – Programming
383
Allows you to view station
messages.
Switch Keymap
399
Toggles between Alpha Mode
and Numeric Mode.
System Forward – On/Off
354
System Speed Dial
381
View Button Assignments
396
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Reverse Transfer (Call Pick-Up)
6
385
4
Answering Calls
Lift the handset, or press
(Speaker) to
answer a call while using a headset or to answer
a call in Handsfree Mode.
Placing Emergency Calls
Dial the emergency number (911 U.S. or
999/112 Europe). The system immediately places
the emergency call as soon as you dial the
number, even if you do not select an outside line.
Placing Internal (Intercom) Calls
With or without the handset lifted, dial the
extension number. If you enter incorrect digits,
you can press
(Hold) to move the cursor
backward, deleting the last digits entered. If you
are using Handsfree Mode, listen for the double
tone, and then begin to speak.
Placing External Calls
Press the Outgoing button, an unlit Call button,
or enter the Outgoing Call access code (8 is the
default code), and then dial the number.
Redialing External Numbers
With or without the handset lifted, press the
(Redial). The system automatically selects
a line and dials the number.
Transferring Calls to Other Extensions
1. While on the call, press
(Transfer), and
then enter the extension number.
2. Do one of the following:
• Wait for an answer, announce the call, and
then hang up. If the extension is
unavailable, press the flashing IC or Call
button to return to the caller.
• Hang up to transfer the call and disconnect
the call from your IP phone.
Forwarding Calls
Placing Conference Calls
1. While on the first call, press the Conf button to
place the call on hold. CALL NEXT PARTY TO
CNF appears.
2. Place a call to the next conference party. For
external calls, press the Outgoing button or
enter the Outgoing Call access code (8 is the
default code), and then dial the number.
3. After the party answers, announce the
conference, and then press the Conf button to
place the call on hold. If necessary, repeat this
step to add the remaining conference party.
4. Press the Conf button again to start the
conference. CNF IN PROGRESS appears.
Viewing and Responding to Messages
1. With the handset on-hook, press
(Message)
or the VIEW MESSAGE menu button. Messages
are displayed as first in/first out. If there is more
than one message, you can repeatedly press
(Message) to scroll through the messages.
2. When the desired message is displayed, press #,
or lift the handset for privacy, and then press # to
respond. (If your handset is off-hook and you
press
[Message], you automatically place a
call to the party or message center who left the
message.)
Using Do-Not-Disturb
1. Press the DND button, and then do one of the
following:
• Press
(Up) or
(Down) to scroll
through the messages.
• Enter the two-digit number for the DND
message.
2. If applicable, enter the additional text for the
DND description.
3. Press
handset.
(Speaker), or lift and replace the
Placing a Page Announcement
1. Press the Fwd button, and then enter the feature
code, if applicable. ENTER FORWARD DEST
appears.
1. Press 7.
2. Enter the extension number, or press the
Outgoing button or enter the Outgoing Call
access code (8 is the default code), and then dial
the telephone number.
3. After the tone, make your announcement, and
then hang up.
2. Enter the page-zone number (0 to 9).
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Notice
This guide is released by Mitel Networks Corporation and provides information necessary to use the
5360 IP Phone. The guide contents, which reflect current Mitel standards, are subject to revision or change without
notice.
Some features or applications mentioned may require a future release and are not available in the initial release.
Future product features and applications are subject to availability and cost. Some features or applications may
require additional hardware, software, or system administrator assistance.
For sales, service, or technical support, contact your local authorized provider:
Enter provider information above.
If you do not know the contact information for your local provider, use the “Partners” link at the top of the Mitel home
page (www.mitel.com) to find a location near you.
If you have any questions or comments regarding this user guide or other technical documentation, contact the
Technical Publications Department (USA) at:
[email protected]
Mitel® is a registered trademark of Mitel Networks Corporation.
All other trademarks mentioned in this document are the property of their respective owners, including Mitel Networks
Corporation. All rights reserved.
© 2010 Mitel Networks Corporation
Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or
promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse
any copyrighted component of this work in other works must be obtained from Mitel.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page i
Important Safety Instructions and Precautions
Remember the following safety guidelines when using the IP phone.
Programming Emergency Numbers
Make sure to do the following when programming emergency numbers and/or making test calls to emergency
numbers:
• Remain on the line and briefly explain to the dispatcher the reason for the call.
• Perform tests during off-peak hours such as early morning or late evenings.
Safety Notices
The following notices may appear on the product or in the technical documentation.
Notice
Description
Caution indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury and/or damage to the equipment or property.
Warning indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
Danger indicates an imminently hazardous situation which, if not avoided, will result in death
or serious injury.
The exclamation point within an equilateral triangle indicates that important operating and
maintenance (servicing) instructions are included in the literature accompanying the
product.
Maintenance and Repair
There are no user serviceable parts inside the IP phone. For repairs, return the IP phone to an authorized Mitel
provider.
NOTE
Page ii
Changes or modifications not expressly approved by Mitel may void the user’s right to operate the
equipment.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Power Requirements
CAUTION
Phone Damage Hazard. To avoid damaging the IP phone, make sure the IP phone is connected to the proper power
supply before powering on. Contact your system administrator for more information.
The IP phone requires any one of the following power supplies:
• Mitel 48-volt DC Ethernet power adaptor 100-240 volt AC 50-60Hz (ES), part number 50005301
• An industry-standard IEEE 802.3af Power over Ethernet (PoE) power supply unit
• IEEE 802.3af compliant Gigabit power supply, part number 51015131
If your IP phone uses a centralized PoE power supply unit, do not use the 48-volt DC Ethernet power adaptor. If
necessary, contact your system administrator for assistance before connecting your IP phone to the centralized power
source.
Make sure the IP phone is plugged into an uninterruptible power supply (UPS). If your IP phone is plugged into the
UPS and the power fails, it should remain powered on for about 10 minutes. If the IP phone is not plugged into a UPS
and the power fails, the current call is dropped and you will not be able to use the IP phone until the power is
restored.
Software Updates
CAUTION
Phone Damage Hazard. Do not use your IP phone or disconnect it from the power supply while it is updating
software.
The IP phone may require occasional software updates when new versions are available. The IP phone is configured
to download the updates automatically. Contact your system administrator for more information.
Product Disposal Instructions
This symbol indicates that the product is classified as electrical or electronic equipment and should not be disposed of with
other commercial or household waste at the end of its working life. For appropriate disposal and recycling instructions,
contact your local Mitel provider.
The Waste of Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC) was established by the European Union to
minimize negative impact on the environment, control hazardous substances, and curtail landfill expansion by using the best
available recovery and recycling techniques.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page iii
Phone Usage
This equipment is not for connection to the telephone network or public coin phone service. It is only for use when
connected to Mitel systems.
WARNING
When using your IP phone equipment, basic safety precautions should always be followed to reduce the risk
of fire, electric shock and injury to persons, including the following:
• Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool.
• Avoid using a phone (other than a cordless type) during an electrical storm. There may be a remote
risk of electric shock from lightning.
• Do not use the IP phone to report a gas leak in the vicinity of a leak.
• Do not connect directly to the Public Switched Telephone Network (PSTN). Any connection of this
phone to an off premise application, an out of plant application, any other exposed plant application, or
to any equipment other than the intended application may result in a safety hazard, and/or defective
operation, and/or equipment damage. “Exposed plant” means where any portion of the circuit is subject
to accidental contact with electric lighting or power conductors operating at a voltage exceeding 300
volts between conductors or is subject to lightning strikes.
• The socket outlet, if used, shall be located near the equipment and shall be easily located by the user.
• Use only Mitel approved power adaptors. See “Power Requirements” on page iii.
• The handset supplied with the IP phone is not certified for use with any other phone. Use of the
handset with any other phone may have the potential to cause hearing loss in the event of a lighting
strike on the outside plant wiring.
Page iv
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Notice to Canadian Customers
The Class B digital apparatus complies with Canadian ICES-003.
Notice to U.S. Customers
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Notice to European Customers
We, Mitel Networks LTD.
Of, Mitel Castlegate Business Park
Portskewett
Caldicot
NP26 5YR
UK
Declare that for the hereinafter mentioned product the presumption of
conformity with the applicable essential requirements of
DIRECTIVE 1999/5/EC OF THE EUROPEAN
PARLIAMENT (RTTE DIRECTIVE) AND OF THE COUNCIL is given.
Mitel IP Phone: 5360
Any unauthorized modification of the product voids this Declaration.
For a copy of the original signed Declaration of Conformity (in full conformance with EN45014), please contact the Regulatory
Approvals Manager at the above address.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page v
Contents
Contents
Getting Started
1
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
About Your IP Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
5360 IP Phone Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Phone Feature Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display and Softkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gadget Sidebar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ring/Message Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialpad Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmable Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigation Page Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
3
3
3
4
5
5
6
6
6
Phone Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Comfort and Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Viewing the Phone Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cleaning Your IP Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using a Headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using the 5310 IP Conference Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Accessing/Exiting the Conference Controller Application . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Turning the Conference Unit On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjusting the Conference Unit Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Muting the Conference Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Placing the Conference Unit in Presentation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using the Line Interface Module (LIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Making and Answering Calls Using the Analog Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Making and Answering Calls Using the Failover Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Personalizing Your Phone
15
Adjusting the Viewing Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Changing Volume Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Changing the Ring Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Adjusting the Display Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Changing the Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Changing the Text Size on the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page vii
Contents
Using the Screen Saver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Specifying Audio Feedback Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Calibrating the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Using the Dialpad Buttons to Enter Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Using Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Default Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Outside Line Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Extension Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Default Feature Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Listening to Background Music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Viewing Button Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Resetting Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Resetting the IP Phone to the Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Switching Keymaps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Turning the Backlight on or off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Activating Door Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Answering and Placing Calls
29
Answering Calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Answering Waiting Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using Automatic Call Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Redirecting Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Using Automatic Trunk Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Placing Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Placing Emergency Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Placing Emergency Calls using the LIM Line. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Placing Internal Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Requesting a Callback (Queuing the Phone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using Camp-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Placing External Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Redialing a Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Using Speed Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Using System Speed Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Using Station Speed Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storing Station Speed-Dial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing Station Speed-Dial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting Station Speed-Dial Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assigning Speed-Dial Numbers to Programmable Buttons . . . . . . . . . . . . . . . . . . . . . . . .
Page viii
34
34
35
35
36
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Contents
Using the Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Using Account Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Call Features
39
Using Handsfree Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Using Ring Intercom Always . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Using Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Placing Calls On Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Entering a Hookflash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Transferring Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Transferring Calls to Other Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Transferring Calls to External Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Using Reverse Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Viewing Your System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Viewing Caller ID Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Forwarding Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Manual Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
System Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Using Dynamic Extension Express . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Placing Conference Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Adding a Conference Party . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Transferring a Conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Dropping Out of a Conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Ending a Conference and Placing all Parties on Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Using Record-A-Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Using Group Listen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Using Call Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Using Secondary Extension Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Using Configuration Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Changing Your Station Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Accessing Configuration Assistant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Changing the Dynamic Extension Express Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Changing the DND Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Changing the Manual Call Forwarding Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Using Remote Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Changing the Dynamic Extension Express Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Changing the DND Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Changing the Manual Call Forwarding Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Changing Your Station Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page ix
Contents
Messages
57
Leaving Messages at Other Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Viewing and Responding to Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Canceling Messages Left at Other Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Deleting Waiting Inter-Station Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Using Do-Not-Disturb (DND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Using Reminder Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Paging Other System Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Placing a Page Announcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Enabling or Disabling the Page Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Hunt Groups
63
Logging in to ACD Hunt Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Logging out of ACD Hunt Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Stopping the ACD Hunt Group Wrap-up Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Other Hunt Group Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Requesting Agent Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Diverting Hunt Group Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Hunt Group Supervisor Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Accepting or Rejecting Agent Help Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Monitoring Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Stealing Hunt Group Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Using Barge-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Cordless Devices
69
Cordless Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Handset and Headset Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Pairing the Cordless Module and Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Using a Cordless Device as a Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Alerting Tones and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Low Battery Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Cordless Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Cordless Handset Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Answering Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Hanging Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Cordless Handset LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Page x
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Contents
Cordless Headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Cordless Headset Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Answering Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Hanging Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Cordless Headset LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Using the Cordless Devices Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Troubleshooting
77
Contact Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Index
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
81
Page xi
Getting Started
Getting Started
Welcome
The instructions in this guide are for using the Mitel 5360 Internet Protocol (IP) Phone on the
Mitel 5000 Communications Platform (CP). The Quick Reference Guide located at the
beginning of this guide is an overview of frequently used features.
Your IP phone should be powered on and ready to use. If the display is blank, or if the display
name, extension number, or time or date are incorrect, contact your system administrator for
assistance.
Because a variety of voice mail products work with the 5000 CP, this guide does not include
voice mail instructions. For voice mail instructions, refer to the voice mail user guide for your
system. For example, refer to the Enterprise Messaging, Basic Voice Mail, and Embedded
Voice Mail Card User Guide, part number 835.3205, or the Mitel NuPoint Unified Messaging
User Guide on the Mitel Web site (http://edocs.mitel.com). Contact your system administrator
for more information about your voice mail system.
NOTE
Because many phone features can be programmed to perform various tasks,
some features may work differently than the descriptions in this guide. Contact
your system administrator for more information.
About Your IP Phone
The 5360 IP phone has a seven-inch (17.8 cm), backlit, high-resolution (800 x 480), color,
touch-screen display with brightness controls. For one-touch feature access, the 5360 has eight
context-sensitive softkeys and 42 self-labeling programmable keys (three pages of 14 each). It
includes an embedded screen saver application and text size control.
The Gadget Sidebar provides one-touch access to embedded applications (such as turning the
display’s backlight on or off). And, a 10/100/1000 auto-sensing Gigabit Ethernet LAN connection
allows unconstrained bandwidth from the network to the desktop. The phone supports the Mitel
Cordless Handset and Headset, the Mitel Line Interface Module, the Mitel 5310 IP Conference
Unit, and the Mitel Wireless LAN Stand.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 1
Getting Started
5360 IP Phone Features
The 5360 IP Phone is shown here.1 See “Phone Feature Descriptions” below for more
information about the phone features.
11
21
31
41
51
61
10
1
71
91
81
1 – Handset (see page 3)
6 – Feature buttons (see page 5)
2 – Display and Softkeys (see page 3)
7 – Dialpad buttons (see page 5)
3 – Status Bar (see page 3)
8 – Programmable buttons (see page 6)
4 – Gadget Sidebar (see page 3)
9 – Navigation buttons (see page 6)
5 – Ring/Message Indicator (see page 4) 10 – External Speaker (see page 6)
1. This image is an example of how your phone may be programmed.
Page 2
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Getting Started
Phone Feature Descriptions
The following sections describe default configurations. Your IP phone may be programmed
differently. Contact your system administrator for more information. See “5360 IP Phone
Features” on page 2 for phone feature locations.
Handset
The handset provided with this equipment is hearing aid compatible (HAC). If you are using a
headset or if you are in Handsfree Mode, you do not need to use the handset. See “Cleaning
Your IP Phone” on page 8 and “Using Handsfree Mode” on page 41 for more information.
Display and Softkeys
The display provides a 800 x 480 (pixels) high-resolution viewing area for selecting and using
features and identifying callers. For one-touch feature access, the 5360 has eight contextsensitive softkeys (four on the left and four on the right). When idle, the display shows user
information, the system time and date, and feature button assignments. Consider the following
when using the display:
• You can adjust the display Brightness levels (see page 16).
• You can control the size of the text that appears on the display for programmable buttons
(see page 18).
The 5360 IP Phone includes an embedded screen saver that you can configure for your display.
Configuration options include the screen saver timeout, display image, and brightness options
(see page 19).
Status Bar
The status bar displays time, date, and icons indicating feature states as follows:
• Call Forward All Calls (
• Message Waiting (
• Headset (
• DND (
) – Indicates Call Forward All Calls is activated.
) – Indicates new voice mail.
) – Indicates that the phone is in headset mode.
) – Indicates that the phone is in DND (Do-Not-Disturb) mode.
• Conference Unit (
) – Indicates that the 5310 IP Conference Unit is connected and
turned on.
Gadget Sidebar
The Gadget Sidebar provides one-touch access to embedded applications. The 5360 IP Phone
currently supports the following applications:
Backlight On/Off ( ): Turns the backlight on and off (see page 16).
• Help (
): Provides access to Quick Help and displays a list of the key icons (see
page 28)
• Phone/Home (
): Returns to the main Phone/Home window.
Additional applications may be added in future releases.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 3
Getting Started
Ring/Message Indicator
The Ring/Message Indicator flashes or stays lit to indicate call, message, and feature activity.
For more information about messaging features, see “Messages” on page 57. Ring/Message
Indicator signals are described in the following table.
Indicator Signals
Page 4
Description
Rapidly flashing
You have an incoming call.
Slowly flashing
You have a waiting message or callback message.
On
You are on a call or using a feature.
Off
Your IP phone is idle.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Getting Started
Feature Buttons
Feature buttons provide quick access to commonly used features. See the following table for
descriptions.
Button
(Up) or
Action
(Down
Provides volume control for the ringer, handset, and speaker.
Scrolls through feature options.
(Speaker)
Activates Handsfree Mode/speakerphone (see page 39).
Activates features.
(Mute)
Temporarily turns off your microphone during a call.
(Applications)
Activates the Applications menu to perform the following options:
• Use the conference unit (see page 9)
• Program the following settings in the Settings application:
o
Change the language on the display (see page 17).
o
Change the text size on the display (see page 18)
o
Adjust the display brightness (see page 16)
o
Use the screen saver (see page 19)
o
Specify audio feedback options (see page 20)
o
Calibrate the display (see page 20)
o
View phone information (see page 8)
• Use cordless devices (see page 69)
• Enable Clean Mode (see page 8)
(Special)
(Redial)
(Hold)
Activates features while on a call. The
(Special) button does not
cancel features. To cancel features, press the Star button (*).
Calls the last external number dialed. You cannot redial internal
numbers.
Places the current call on hold and retrieves a call from hold.
Left/backspace when entering dialpad characters (see page 21).
(Transfer)
Transfers the current call.
Right/forward when entering dialpad characters (see page 21).
(Message)
Displays station messages.
Toggles between Alpha Mode and Numeric Mode when entering
dialpad characters.
Dialpad Buttons
Use the dialpad buttons to dial phone numbers, enter feature codes, and to enter characters
when using features that require text input.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 5
Getting Started
Programmable Buttons
The 5360 IP Phone has 42 self-labeling programmable keys using a touch-screen display (three
pages of 14 each). Each phone has the following buttons that are programmed by the system
administrator and cannot be reprogrammed; however, you can program the remaining buttons
for quick access to features or speed-dial entries. See “Using Programmable Buttons” on
page 24.
Button
Action
DND
Turns DND mode on or off.
Outgoing
Selects an outgoing line for external calls.
Call Key 1
Selects an outside line or answers a call.
Call Key 2
Selects an outside line or answers a call.
IC
Answers an intercom (internal) call.
Conference
Places a conference call.
Forward
Forwards the call to the specified number.
Navigation Page Buttons
The 5360 IP Phone has three Navigation Page icons located in the bottom right hand corner of
the display to navigate between the IP phone’s three display pages. When a page icon in the
bottom right-hand corner of the Display blinks, it means that there is real-time activity on the
page where the number or feature is located.
If you navigate to the second or third pages, you must use the Navigation Page buttons to
return to the first page. You are not automatically returned to the first page after using features
or when the IP phone is idle. You can also press the
(Home) button on the 5360 IP Phone
(only) to return to the first page.
External Speaker
The speaker provides audio for handsfree calls and background music. See “Using Handsfree
Mode” on page 39 for information about handsfree calls. See “Listening to Background Music”
on page 27 for more information about background music.
Page 6
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Getting Started
Phone Signals
The 5360 IP Phone has several audio and visual signals to indicate feature activity. The
following are a few helpful tips:
• Lit or blinking buttons indicate call or feature activity.
• All phone button lamps illuminate at the same time for a few seconds when the IP phone
is reset or powered on.
• The following actions may cause an error tone:
o
Pressing an invalid button combination.
o
Selecting a restricted feature.
o
Dialing a restricted or invalid number.
o
Dialing too slowly between digits.
o
Waiting too long before performing the next step.
To correct an error tone, hang up and try again.
• Many features “time-out” if you wait too long before performing the next step. If this
happens, you must start over.
• “Off-hook” means the handset is lifted. “On-hook” means the handset is in the cradle.
• If your IP phone does not have a lamp under the speaker button, the large message
indicator lamp on the top right of the IP phone indicates that the speakerphone is in use.
Comfort and Safety Tips
Observe the following comfort and safety tips when using the IP phone:
• Do not cradle the handset: Prolonged use of the handset can lead to neck, shoulder, or
back discomfort, especially if you cradle the handset between your neck and shoulder. If
you frequently use the IP phone, you might find a headset more comfortable. “Using a
Headset” on page 8.
• Adjust the viewing angle: The built-in stand tilts to give you a better view of the buttons.
See “Adjusting the Viewing Angle” on page 15.
• Protect your hearing: Because prolonged exposure to loud sounds can contribute to
hearing loss, keep the volume at a moderate level. You can adjust the volume levels of the
handset receiver or headset. See “Changing Volume Levels” on page 16.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 7
Getting Started
Viewing the Phone Information
You can use the phone to view system or phone information.
To view system information:
1.
Press
(Applications).
2.
Press Settings, and then press About 5360 IP Phone. The About menu appears.
3.
Press X (Close) to exit the About menu, and then press Close to exit the Applications
menu.
Cleaning Your IP Phone
You can wipe and clean the touch screen of your 5360 IP Phone without causing touchsensitive controls to be activated.
To enable Clean Mode when you clean the screen of your phone:
1.
Press
(Applications).
2.
Press Clean Mode.
3.
Clean the screen of your phone.
4.
Press
(Applications) to end Clean Mode.
Using a Headset
When using a headset, press
(Speaker) to connect to or disconnect from calls. The
Headset icon
appears when the headset is in use. You cannot use the handset or
speakerphone when the IP phone is in Headset Mode. Disconnecting the headset automatically
enables the handset.
The headset must be hearing aid compatible (HAC).
NOTES
If your headset has a power-saver mode, make sure the system administrator has
enabled the “Headset Connect Tone” feature. If this is not enabled, you may miss
the first few seconds of an incoming call.
To connect and activate the headset:
1.
Insert the headset jack into the Headset port
2.
Dial 317 (Headset on/off). HEADSET MODE ON appears.
NOTE
located on the back of the IP phone.
Because Headset Mode disables the handset and speakerphone, you
must turn off Headset Mode before you can use the handset or
speakerphone.
To turn off Headset Mode and activate the handset and speakerphone:
Dial 317 (Headset on/off). HEADSET MODE OFF appears.
Page 8
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Getting Started
Using the 5310 IP Conference Unit
Your IP phone can use the 5310 IP Conference Unit (shown below) for full-duplex, advanced IP
conferencing. Use the Conference Controller touch screen to turn the Conference Unit on or off,
to adjust the volume or to put the Conference Unit into Presentation mode. You can only run
one Conference Controller session at a time. If the 5310 Conference Unit is not connected to
your IP phone, the Conference Controller application is not available.
Installation instructions are included with the unit.
Mitel 5310 IP Conference Unit
5310 IP Conference Unit
For information about placing conference calls and adding parties to the conference, see
“Placing Conference Calls” on page 47.
Accessing/Exiting the Conference Controller Application
You must first access the Conference Controller application to use the Conference Unit.
To access the Conference Controller application:
1.
Press
2.
Press Conference Unit.
(Applications).
To exit the Conference Controller application:
Press Close in the Conference Controller application.
Turning the Conference Unit On and Off
The following instructions describe how to turn the Conference Unit on and off.
To turn the Conference Unit on and off:
Press Turn On or Turn Off in the Conference Controller application. If applicable, the
icon appears in the IP phone status line while the Conference Unit is on.
NOTE
Turning the 5310 Conference Unit off terminates the active call. To continue the call
either pick up the handset or press the Speaker button on the IP phone.
Adjusting the Conference Unit Volume
The following instructions describe how to adjust the Conference Unit volume.
To adjust the Conference Unit volume:
Press Volume Up or Volume Down.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 9
Getting Started
Muting the Conference Unit
You can mute the Conference Unit so that conversation or noise near the Conference Unit
cannot be heard by individuals being conferenced.
To mute the Conference Unit:
Press Mute.
Placing the Conference Unit in Presentation Mode
Presentation Mode should be used when only one individual will be speaking into the
Conference Unit. If another individual near the unit wishes to speak, you should disable
Presentation Mode. Presentation Mode minimizes extraneous noise.
To enable/disable Presentation Mode:
Toggle Presentation Mode on or off in the Conference Controller application.
Page 10
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Getting Started
Using the Line Interface Module (LIM)
The LIM is an optional device that adds an analog phone line capability to your IP phone. In the
event of a network failure, the IP phone can be configured to use the public switched telephone
network (PSTN) to provide continued basic telephony until service in restored. The analog line
can also be used for emergency calls and local calling.
Line Interface Module
Ethernet
Connection
Analog PSTN
Connection
You can use the LIM to:
• allow incoming and outgoing analog PSTN calls directly to and from the IP phone
• provide survivability (failover) in the event IP connectivity is lost
• provide emergency dialing support (emergency calls can be programmed to connect
through the analog PSTN connection)
If you have a LIM connected to your IP phone, all programming of the LIM, except the Analog
button (key), is done by the Installer when your IP phone is installed. To program the Analog
button, see “Using Programmable Buttons” on page 24.
The LIM operates in one of the following two modes, as determined by your System
Administrator:
• LIM Mode: You can use the LIM line at any time.
• Failover Mode: You can use the LIM line only when the IP connection has failed.
NOTE
Handsfree and on-hook dialing are not supported on the LIM line.
For information on emergency number dialing using the LIM, see “Placing Emergency Calls
using the LIM Line” on page 33.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 11
Getting Started
Making and Answering Calls Using the Analog Button
To make a call using the Analog line:
1.
Lift the handset.
2.
Press the button you programmed as Analog Line. ANALOG CALL appears.
3.
Dial the number.
NOTE
When you make an external call over the analog line, a prefix dialing number is not
required. If your IP phone’s Analog Line button has the Privacy option enabled, you
cannot access the analog line when another phone is using the analog line (button is
solid orange).To access the analog line, the user of the other phone must first hang
up. To determine whether the Privacy option is enabled, contact your System
Administrator.
To answer a Call using the analog line:
1.
Lift the handset.
2.
Press the Analog Line button that is highlighted.
To answer a waiting call on the analog line:
NOTE
If you have subscribed to an analog call waiting service, you may use the hookswitch
or press the Star button (*) to answer a waiting analog call. When you are on an
analog call and a waiting analog call arrives, you hear a beep. This feature may not
be supported in all regions.
To answer a waiting analog call or return to the original analog call:
1.
Do one of the following:
• Press and release the hookswitch.
• Press the Star button (*) to cancel.
2.
Press the button you have programmed as Analog Line.
To put a current call on hold to answer an incoming analog call:
Press the highlighted Analog Line button.
To switch between the current call and the held call when one of the calls is using the
analog line, do one of the following:
• If your current call is using the analog line, press the flashing Line button of the held call.
The analog call is automatically put on hold.
• If your current call is using an IP line, press the highlighted Analog Line button. The IP
line is automatically put on hold.
To end a current call when an incoming analog call arrives:
Press the Star button (*) and then press the highlighted Analog Line button. The current
call ends and you are connected to the caller on the analog line.
To end the current analog call when an incoming call arrives:
Press the Star button (*) to cancel. The current analog call ends and you are connected
to the new caller.
Page 12
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Getting Started
Making and Answering Calls Using the Failover Mode
To make a call using the analog line during an IP connection failure:
1.
Lift the handset. IP FAIL: ANALOG CALL appears.
2.
Dial the number.
To answer a call using the analog line during an IP connection failure:
Lift the handset. The call is answered. IP FAIL: ANALOG CALL appears.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 13
Personalizing Your Phone
Personalizing Your Phone
This chapter describes features you can use to personalize your IP phone.
Adjusting the Viewing Angle
You can tilt the IP phone stand for a better view of the buttons and display.
Press tabs on both sides
to release and detach unit.
To adjust the viewing angle:
1.
Turn the IP phone so it faces away from you.
2.
Hold the base firmly, and then press the tabs on the sides of the stand to release and
detach the base unit.
3.
Hinge the hooks on the base unit into the notches on the back of the IP phone, and then
snap into place as follows:
• For a high-angle mount, hinge the two lower hooks into the bottom set of notches,
and then snap the two upper hooks into the middle set of notches.
• For a low-angle mount, hinge the two lower hooks into the middle set of notches,
and then snap the two upper hooks into the top set of notches.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 15
Personalizing Your Phone
Changing Volume Levels
You can change the following volume levels:
• Ringer (alerting tone)
• Handset
• Headset
• Background music
• External speaker
NOTE
Turning the external speaker volume down to the lowest levels may prevent you
from hearing the feature “warning tones” that notify you when errors occur (for
example, when you enter an incorrect feature code).
You must be using the feature to change the volume level. For example, if you want to change
the handset volume level, you must be using the handset. However, you can adjust the ringer
(alerting tone) volume level when the IP phone is idle.
To change a volume level:
While using the feature, press
(Up) to increase the volume, or press
decrease the volume. The volume level is automatically saved.
(Down) to
Changing the Ring Tone
You can select one of nine different ring tones.
To change the ring tone:
1.
With the handset on-hook, dial 398.
2.
Do one of the following to listen to (or turn off) ring tones:
• Press 0 or the RINGER OFF menu button to turn the ringer off.
• Press (Up) or (Down) or 1 to 9 to listen to ring tones.
• Press the PREVIOUS or NEXT menu button to listen to and select a ring tone.
3.
Press
(Speaker), #, the ACCEPT menu button, or lift and replace the handset to
select the ring tone.
Adjusting the Display Brightness
You can adjust the display Brightness levels.
NOTE
By default, the IP phone display dims to 20 percent of the maximum brightness level
after 5 minutes of inactivity (no button presses or audio, including background
music). If the brightness is set at the lowest level, you may not notice when the
display dims.
To adjust the Brightness level:
Page 16
1.
Press
(Applications).
2.
Press Settings, and then press Brightness.
3.
Press (Brightness) + or – to find the level you want to use.
4.
Press # or Save to save the setting, and then press Close to exit the Applications menu.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Personalizing Your Phone
Changing the Language
You can change the language to display text on your phone. Your system is programmed to
support two of the following languages:
• English
• French
• LA (Latin America) Spanish
To change the language on the display:
1.
Press
(Applications).
2.
Press Settings, and then press Languages.
3.
Press the language that you want to use.
4.
Press # or Save to save the setting, and then press Close to exit the Applications menu.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 17
Personalizing Your Phone
Changing the Text Size on the Display
You can control the size of the text that appears on the display for programmable buttons. This
enhancement does not apply to the text size that appears on the display for the menu buttons.
Text size options include:
• Small text (default): Provides a first line of basic information and a second line of
supplemental information for the features and functions programmed for the button.
• Large text: Provides one line of basic information for the features and functions
programmed for the button. Large text is enabled by default.
The table below includes several examples for the small text and large text display options.
Programmable
Button
Small Text
Example
Large Text
Example
Station Speed Dial
Monica S
Monica S
The station speed-dial number
programmed for the button.
Chandler TS
The system speed-dial number
programmed for the button.
25598
System Speed Dial
Chandler TS
4809619000
Direct Station
Selection (DSS)
Jessica A
Jessica A
28899
Programmable
Feature
DND
IC
The extension number programmed
for the user.
DND
The feature code that corresponds
to the feature programmed for the
button.
IC
The name or number for the other
party on the internal call.
(372)
Intercom Call (IC)
Second line provides:
Charlie B
To change the text size on a display:
Page 18
1.
Press
(Applications).
2.
Press Settings, and then press Text Size.
3.
Press Large Text or Small Text.
4.
Press Save, and then press Close to exit the Applications menu.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Personalizing Your Phone
Using the Screen Saver
The IP Phones include an embedded screen saver that you can configure for your display.
By default the screen saver image is disabled. When your IP phone enters screen saver mode,
only the IP phone’s backlight dims. The 5360 IP Phone has a backlit display.
You can enable the screen saver image and when your IP phone enters screen saver mode, the
IP phone’s backlight dims and the embedded nature screen saver images appear on your
display. The images are not changeable.
To configure the screen saver on your IP Phone:
1.
Press
(Applications).
2.
Press Settings, and then press Screen Saver. The Screen Saver menu appears.
3.
Configure your screen saver options:
a. Select one of the following screen saver timeout options:
o
15 minutes
o
10 minutes
o
5 minutes
o
1 minute
b. If desired, enable the Display Image option:
o
If you enable the Display Image option, the screen saver image appears and
your backlight dims when your IP phone enters screen saver mode, as
specified by the screen saver timeout setting.
o
If you disable the Display Image option, only your backlight dims (if your IP
phone has a backlight) when your IP phone enters screen saver mode, as
specified by the screen saver timeout setting. This is the default setting.
c. Configure brightness options if your IP phone has a backlight.
Options include:
o
Brightness+: Increases the brightness of the display when your IP phone is
in screen saver mode.
o
Brightness-: Decreases the brightness of the display when your IP phone is
in screen saver mode.
o
Show Brightness: Shows the brightness level of the display when your IP
phone is in screen saver mode. The display returns to normal after
approximately two seconds.
4.
Press Save.
5.
Press Close to exit the Applications menu.
To wake your IP phone from screen saver mode:
Lift the handset or press any button to wake the IP phone.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 19
Personalizing Your Phone
Specifying Audio Feedback Options
The Audio Feedback setting allows you to adjust the volume of the audio feedback as well as
the error beeps, and enable or disable the setting.
The error beep volume in the phone is related to the volume of the speaker. You can set the
beep volume using this procedure; however, adjusting the speaker volume also affects the beep
volume.
To adjust the volume of the audio feedback:
1.
Press
(Applications).
2.
Press Settings, and then press Audio Feedback.
3.
Set the audio feedback options for the button beep and error beep.
• To turn audio feedback on or off, press
or
• To adjust the volume level, press
.
or
.
• To play the beep, press Play button beep or Play error beep.
4.
Press Save.
5.
Press Close to exit the Applications menu.
Calibrating the Display
You can calibrate the touch display for optimum touch sensitivity.
To calibrate the phone screen for touch accuracy:
Page 20
1.
Press
(Applications).
2.
Press Settings, and then press Calibrate Display.
3.
Touch the center of each + to calibrate the display.
4.
Press OK, and then press Close.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Personalizing Your Phone
Using the Dialpad Buttons to Enter Characters
You can use the dialpad buttons to enter text or numbers for features such as Do-Not-Disturb
(see page 59) and Station Speed Dial (see page 34).
The following are guidelines when entering dialpad characters:
• Press
(Message) to switch from Alpha Mode to Numeric Mode. The
button stays lit in Alpha Mode and is off in Numeric Mode.
• Press
(Message)
(Hold) to move the cursor to the left and delete characters.
• Press
(Transfer) to move the cursor to the right.
• In Numeric Mode, press # for a hyphen (-).
• In Numeric Mode, press * for a colon (:).
• Press #,
(Speaker), or lift and replace the handset to save entries.
To use the dialpad to enter characters:
Press the dialpad buttons as shown in the following table.
Dialpad Characters — American English and British English
Number of Times Dialpad Button is Pressed
Button
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
:
-
/
,
.
;
(
)
&
+
*
!
?
#
1
2
A
B
C
2
a
b
c
3
D
E
F
3
d
e
f
4
G
H
I
4
g
h
i
5
J
K
L
5
j
k
l
6
M
N
O
6
m
n
o
7
P
Q
R
S
7
p
q
r
s
8
T
U
V
8
t
u
v
9
W
X
Y
Z
9
w
x
y
z
0
0
For example, to enter May 31, you could use the following sequence:
1. In Alpha Mode (
[Message] button is lit), press 6 once to enter an “M.”
2. Press 2 five times to enter an “a.”
3. Press 9 eight times to enter a “y.”
4. Press
5. Press
(Transfer) to enter a space.
(Message) to switch to Numeric Mode.
6. Press 3.
7. Press 1.
8. Press
(Speaker), #, or lift the handset to save the entry.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 21
Personalizing Your Phone
The following tables show the dialpad characters for the Canadian French and Mexican Spanish
languages.
Dialpad Characters — Canadian French
Number of Times Dialpad Button is Pressed
Button
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
:
-
/
,
.
;
(
)
&
+
*
!
?
#
1
2
A
B
C
2
A
b
c
À
Â
Æ
Ç
à
â
æ
ç
3
D
E
F
3
D
e
f
È
É
Ê
Ë
è
é
ê
ë
4
G
H
I
4
G
h
i
Î
Ï
î
ï
5
J
K
L
5
J
k
l
6
M
N
O
6
M
n
o
Ô
Œ
ó
œ
7
P
Q
R
S
7
p
q
r
s
8
T
U
V
8
T
u
v
Ù
Û
Ü
ù
û
Ü
9
W
X
Y
Z
9
w
x
y
z
Ÿ
Ÿ
0
«
»
0
Dialpad Characters — Mexican Spanish
Number of Times Dialpad Button is Pressed
Button
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
:
-
/
,
.
;
(
)
&
+
*
!
?
#
1
2
A
B
C
2
A
b
c
Á
Á
3
D
E
F
3
D
e
f
É
é
4
G
H
I
4
G
h
i
Í
Í
5
J
K
L
5
J
k
l
6
M
N
O
6
M
n
o
Ñ
Ó
ñ
ó
7
P
Q
R
S
7
p
q
r
s
8
T
U
V
8
T
u
v
Ú
Ü
ú
ü
9
W
X
Y
Z
9
w
x
y
z
0
¡
¿
ª
º
0
Page 22
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Personalizing Your Phone
Using Programmable Buttons
For quick access, you can assign feature codes, extensions, speed-dial numbers, trunks, or
other resources to your programmable buttons. The new button assignments are self labeled,
which means the button labels automatically appear on the Display when the buttons are
programmed. You can then press the programmed buttons to activate features or place calls.
See “Default Access Codes“ and “Default Feature Codes” on page 24 for code lists. You cannot
reprogram the default button assignments. See “Programmable Buttons” on page 6.
To program a button:
1.
With the handset on-hook, dial 397.
2.
Press the button that you want to program. If the button is:
• not programmed, UNDEFINED KEY appears.
• programmed, the feature or extension programmed for the button appears.
• not programmable, NON-PROGRAMMABLE KEY appears.
3.
Enter the feature code, extension number, station speed-dial number, or system speeddial number to be assigned to the button. To assign speed-dial numbers to
programmable buttons, see “Assigning Speed-Dial Numbers to Programmable Buttons”
on page 36.
NOTE
Before or after assigning the speed-dial number to a programmable button,
make sure the speed-dial number has either a Station Speed Dial bin or
System Speed Dial location assigned to it. For System Speed Dial numbers,
numbers are pre-assigned to the System Speed Dial locations (000 to 999
or 0000 to 4999) by your system administrator. Therefore, you just need to
choose a System Speed Dial location that you want to use (see “Using
System Speed Dial” on page 34 for details). For Station Speed Dial
numbers, you must manually store numbers in the Station Speed Dial bins
(0 to 9). See “Using Station Speed Dial” on page 34.
After you program a button, you can:
• Press the button to place a call to the assigned extension.
• Press the button and then hang up to transfer a call to the assigned extension. If the call is
transferred to voice mail you hear repeating double tones.
• Visually monitor the call activity of the assigned extension if the button you assign has a
lamp.
The following table describes the lamp signals and the indicated call activity for a DSS/BLF key
(station speed-dials do not show status).
Lamp Signals
Description
Continuously Lit
The extension is busy or off-hook.
Slowly flashing
The extension is in Do-Not-Disturb (DND).
Quickly flashing
The extension has a call ringing in.
Continuously flashing
The extension is causing a “Station Off-Hook” system alarm.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 23
Personalizing Your Phone
Default Access Codes
The following are default system access codes. If your system uses different codes, record the
codes in the “New Code” column for reference.
Outside Line Access Codes
Code Type
Emergency Call
Code
New Code
911 (999/112 Europe)
Outgoing Call (Default)
8
Select Line Group 1 to 208
92001 to 92208
Automatic Route Selection
92000
Extension Numbers
Code Type
Attendant
Code
New Code
0
Phone Extensions
1000 to 1999
Hunt Groups
2000 to 2299
Default Feature Codes
The following table lists default feature codes. If your system administrator changes any of the
default codes, you can record the new codes in the “New Code” column for reference.
NOTE
Most of the following feature codes work when your IP phone is idle. However, if
you are on an active call or if the IP phone is off-hook, you may need to press
(Special) before you enter the feature code to activate the feature.
To delete the characters entered:
Press
(Hold) to move the cursor to the left and delete the characters entered.
To cancel the feature:
Press *.
Feature
Page 24
Page
Code
Account Code – Follow Calls
38
391
Account Code – Optional
38
390
ACD Agent – Log In
63
326
ACD Agent – Log In/Out
63
328
ACD Agent – Log Out
63
327
ACD Agent – Wrap-up Terminate
64
329
Activate Door Relay
28
332
Agent Help – Reject
65
376
Agent Help – Request
65
375
New Code
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Personalizing Your Phone
Feature
Page
Code
Answer Ringing Call
29
351
Automatic IC Access – On/Off
29
361
Automatic Trunk Access – On/Off
29
360
Automatic Trunk Answer
30
350
Background Music – On/Off
27
313
Barge-In
67
386
Call Forward – All Calls
43
355
Call Forward – If Busy
43
357
Call Forward – If No Answer
43
356
Call Forward – No Answer/Busy
43
358
Call Logging
49
333
Conference
46
5
Default Station
28
394
Directory
37
307
Display Time And Date
42
300
Do-Not-Disturb
59
370
Do-Not-Disturb – Cancel
59
371
Do-Not-Disturb – On/Off
59
372
Do-Not-Disturb – Override
59
373
Dynamic Extension Express On
44
363
Dynamic Extension Express Off
44
362
Dynamic Extension Express On/Off
44
364
Dynamic Extension Express Handoff
44
388
Group Listen
48
312
Handsfree – On/Off
39
319
Headset – Off
8
316
Headset – On
8
315
Headset – On/Off
8
317
Hold – Individual
40
336
Hold – System
40
335
Hookflash (Recall in Europe)
40
330
Hunt Group – Remove
65
322
Hunt Group – Remove/Replace
65
324
Hunt Group – Replace
65
323
Display Contrast Control
16
303
Message – Cancel Left Message
58
366
Message – Delete Message
58
368
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
New Code
Page 25
Personalizing Your Phone
Feature
Page 26
Page
Code
Message – Leave Inter-station Message
57
367
Message – View Messages
58
365
Microphone Mute – On/Off
39
314
Page
61
7
Page Receive – On/Off
61
325
Program Buttons
23
397
Program Station Password
54
392
Programmable Buttons – Return to Default
27
395
Queue (Callback) Request
32
6
Record-A-Call
48
385
Redial
33
380
Redirect Call
30
331
Reminder Message
59
305
Reminder Message – Cancel
59
306
Remote Programming
54
359
Reverse Transfer (Call Pick-Up)
41
4
Ring Intercom Always – On/Off
39
377
Ring Tone Selection
16
398
Station Monitor
66
321
Station Speed Dial
34
382
Station Speed Dial – Programming
34
383
Steal Call
66
387
System Forward – Off
43
353
System Forward – On
43
352
System Forward – On/Off
43
354
System Speed Dial
34
381
Switch Keymap
28
399
Transfer To Hold
41
346
Transfer To Ring
41
345
View Programmable Button Assignments
27
396
New Code
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Personalizing Your Phone
Listening to Background Music
If your system is equipped with a music source, you can listen to background music or system
audio (for example, organizational conference calls) through the external speaker.
To turn on or turn off background music:
Dial 313 (on/off). BACKGROUND MUSIC ON (or OFF) appears.
Viewing Button Assignments
You can view programmable button (key) feature assignments.
To view button assignments:
1.
With the handset on-hook, dial 396. PRESS THE KEY TO REVIEW appears.
2.
Press any of the feature buttons to display the assignment.
3.
Press # or
(Speaker) to exit.
Resetting Programmable Buttons
You can reset all buttons (keys) that you have programmed to the default assignments.
Resetting the programmable buttons does not reset button assignments programmed by the
system administrator.
To reset the feature buttons to the default values:
With the handset on-hook, dial 395. FEATURE KEYS DEFAULTED appears.
Resetting the IP Phone to the Default Settings
Resetting the IP phone to the default settings does the following:
• Returns all volume settings to the default levels. See “Changing Volume Levels” on
page 16.
• Cancels Background Music. See “Listening to Background Music” on page 27.
• Cancels Callback (queue) requests. See “Requesting a Callback (Queuing the Phone)” on
page 32.
• Restores Handsfree Mode. “Using Handsfree Mode” on page 39.
• Cancels Manual Call Forwarding. See “Manual Call Forwarding” on page 43.
• Cancels System Forwarding. See “System Forwarding” on page 43.
• Cancels Do-Not-Disturb (DND). See “Using Do-Not-Disturb (DND)” on page 59.
• Restores Page settings. See “Paging Other System Users” on page 61.
• Resets hunt group calls. See “Hunt Groups” on page 63.
To reset your IP phone to the default settings:
Dial 394. STATION DEFAULTED appears.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 27
Personalizing Your Phone
Switching Keymaps
Keymaps are the default button assignments on your IP phone. Your system administrator may
have programmed an alternate keymap, allowing you to switch between keymap assignments.
Contact your system administrator for more information.
To switch between keymaps when your IP phone is idle:
With the handset on-hook, dial 399. The display shows either ALTERNATE (or)
STANDARD KEYMAP IS ACTIVE.
To switch between keymaps during a call:
Press
(Special), and then dial 399.
Turning the Backlight on or off
You can turn the backlight on or off on your display.
To turn the backlight on:
Click the Backlight On/Off icon ( ) in the Gadget Sidebar.
To turn the backlight off:
Click the Backlight On/Off icon ( ) again in the Gadget Sidebar.
Getting Help
You can access the 5360 IP Phone Help.
To access the 5360 IP Phone Help:
1.
Click the Help icon (
window appears.
) in the Gadget Sidebar. The Welcome to the 5360 Help System
2.
Press the information that you want to view, and then do any of the following:
• To navigate to the previous or next window, press
• To return to the main Help window, press
• To exit, press
or
.
.
once or twice.
Activating Door Relay
If the Activate Door Relay feature is enabled, you can unlock a door (i.e., “buzz” it open)
through your IP phone.
You can enter the Activate Door Relay feature code while idle or while on a call. This allows you
to activate the feature while talking to a communications device mounted at the door without
first having to hang up. When activated while on a call, the feature will not affect the call in
progress other than to show a short confirmation on the display.
You can add the Activate Door Relay feature to a phone keymap button, just like any other
station feature.
To unlock a door:
While idle or while on a call, dial 332. The door is unlocked.
Page 28
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Answering and Placing Calls
Answering and Placing Calls
The following instructions describe how to answer and place internal and external calls and how
to use related features.
NOTE
By default, internal (intercom) calls are assigned to the IC button, and external calls
are assigned to the Call Key buttons.
Answering Calls
Your IP phone may be preset to automatically answer incoming internal calls in Handsfree
Mode. To disable Handsfree Mode, see “Using Handsfree Mode” on page 39. After disabling
Handsfree Mode, you can use your handset or headset to answer incoming calls.
To answer a call:
Lift the handset, or press
(Speaker) to answer a call while using a headset, or to
answer a call in Handsfree Mode. See “Using Handsfree Mode” on page 39.
If you are currently on a call, press the flashing IC or Call Key button to answer a waiting
call. See “Answering Waiting Calls” below.
Answering Waiting Calls
If you receive a call while you are on another call, you hear a “call waiting” tone, the IC or Call
button flashes, and the display shows the Caller ID information (if available).
To answer a waiting call:
Press the flashing IC or Call Key button. This action hangs up on the connected call and
connects you to the waiting call. You can also place the first call on hold before you
answer the waiting call. See “Placing Calls On Hold” on page 40.
Using Automatic Call Access
Automatic Call Access connects you to incoming internal or external calls when you pick up the
handset or press
(Speaker). When Automatic Call Access is turned off, you must press the
flashing IC or Call Key button to answer incoming calls.
To use Automatic Call Access for incoming IC calls:
With the handset on-hook, dial 361 to turn on (or off). AUTO IC ACCESS ON (or OFF)
appears.
To use Automatic Call Access for incoming external (trunk) calls:
With the handset on-hook, dial 360 to turn on (or off). AUTO TRNK ACCESS ON (or
OFF) appears.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 29
Answering and Placing Calls
Redirecting Calls
You can redirect calls to another extension or external number. If you have a 5360 IP Phone,
you can use the menu buttons to redirect calls to the following destinations:
• SEND TO V-MAIL: Sends the call directly to your voice mailbox. You must have a mailbox
to use this destination.
• IC CALL TO DND: Places your IP phone in DND Mode and blocks the call. See “Using
Do-Not-Disturb (DND)” on page 59.
• SEND TO DEST: Redirects the call to the extension or phone number entered.
To redirect calls:
1. While a call is ringing, dial 331 or press the menu button as described above.
2. Do one of the following:
• Dial the extension number, or press the Outgoing button or the Outgoing Call
access code (the default code is 8), and then dial the external number.
• Enter the DND code.
Using Automatic Trunk Answer
You can use Automatic Trunk Answer to answer incoming external calls for other internal parties
who are members of an “Answer Access” list. Your system administrator creates Answer
Access lists. Contact your system administrator for Answer Access list extensions.1
Automatic Trunk Answer answers calls in the order they are received (that is, the first call
received by any extension in the Answer Access list is the first one answered).
To use Automatic Trunk Answer:
1. While an incoming external call is ringing at another Answer Access list extension, lift the
handset or press
(Speaker).
2. Dial 350 or press the flashing Trunk <number> button.
1.
Page 30
This feature may or may not be enabled for your system.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Answering and Placing Calls
Placing Calls
The following instructions describe how to place calls and related features.
Placing Emergency Calls
WARNING
Contact your system administrator and your local Mitel provider for important information about
dialing emergency services before using your IP phone.
When dialing an emergency number (911 U.S. or 999/112 Europe), you do not have to press
the Outgoing button or enter the Outgoing Call access code (8 is the default code). The system
automatically places emergency calls immediately after you dial the number, even if you do not
select an outside line.
Placing Emergency Calls using the LIM Line
Emergency Number dialing should only be performed by picking up the handset and selecting
the Analog Line key you have programmed. If Privacy Mode is enabled and the Analog Line key
local line is busy, dialing will not occur on the LIM line. Emergency dialing using an IP
connection may not be supported due to system configuration and country location. For more
information, contact your System Administrator. For details about LIM, see “Using the Line
Interface Module (LIM)” on page 11.
To make an Emergency Call using the Line Interface Module line:
1. Lift the handset.
2. Press the Analog Line key that you have programmed. ANALOG CALL appears.
3. Dial your local emergency number.
To make an Emergency Call using the Line Interface Module line, when the IP connection
has failed:
1. Lift the handset.
2. Press the Analog Line key that you have programmed. IP FAIL: ANALOG CALL
appears.
3. Dial your local emergency number.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 31
Answering and Placing Calls
Placing Internal Calls
Internal calls are calls placed to other extensions in the system. Internal calls are assigned to
the Intercom (IC) button on your IP phone. Contact your system administrator for a list of
extension numbers.
To place an internal call:
With or without the handset lifted, dial the extension number. If you enter incorrect digits,
you can press
(Hold) to move the cursor backward, deleting the last digits entered.
If you are using Handsfree Mode, speak after you hear a double tone.
If there is no answer or if the extension is busy, you can do the following:
• Request a callback (queue). See “Requesting a Callback (Queuing the Phone)” below.
• Camp-on to the busy extension. See “Using Camp-on” below.
• Leave a message. See “Leaving Messages at Other Extensions” on page 57.
Requesting a Callback (Queuing the Phone)
When you request a callback (queue the phone), the system calls you when the extension is
available and places a call to the IP phone.
To request a callback:
If there is no answer or if the extension is busy, press
(Special) followed by 6 or the
QUEUE menu button, and then hang up. QUEUE REGISTERED FOR <name> appears.
When the extension becomes available, your extension rings.
To cancel the callback request:
Press 6 or the CANCEL QUEUE menu button. QUEUE REQUEST CANCELED appears.
Using Camp-on
Camp-on keeps you connected to the called extension until it becomes available. You cannot
use Camp-on if the called extension is in DND, or if the call is forwarded to voice mail. See
“Using Do-Not-Disturb (DND)” on page 59.
To use Camp-on:
Stay on the line and wait for the extension to become available. Do not hang up. If Campon is enabled, you hear Music-on-Hold while you are waiting.
Page 32
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Answering and Placing Calls
Placing External Calls
The following sections describe features used when placing external calls.
To place an external call:
1. Press the Outgoing button, an unlit Call Key button, or enter the Outgoing Call access
code (8 is the default code).
2. Dial the number.
NOTES
If you cannot place an external call because all outgoing lines are busy, you
can request a callback, which prompts the system to contact you when a
line becomes available. See “Requesting a Callback (Queuing the Phone)”
on page 32.“
If you are prompted for an account code (indicated by a single beep), you
must enter an account code before you can place your call. See “Using
Account Codes” on page 38.
Depending on system configuration, you may also be able to use one of the following methods
to select an outgoing line:
• Enter the Select Line Group feature code. The default codes are 92001 to 92208.
• Enter the Automatic Route Selection (ARS) feature code. The default code is 92000.
Contact your system administrator for more information about using Select Line Group or ARS
access codes.
Redialing a Number
You can quickly redial the last external number dialed. You cannot redial extension numbers.
To use Redial:
With or without the handset lifted, press
a line and dials the number.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
(Redial). The system automatically selects
Page 33
Answering and Placing Calls
Using Speed Dial
You can use speed dial to quickly dial stored phone numbers. Speed-dial numbers are either
stored in the system (System Speed Dial), or in your IP phone (Station Speed Dial).
Using System Speed Dial
Your system administrator assigns System Speed Dial location numbers, which are available to
anyone in the system. Contact your system administrator for more information.
To view or dial System Speed-Dial numbers:
1. Dial 381. REVIEW SYS SPEED # <code range> appears.
2. Do one of the following:
• Press
(Up) or
(Down) to scroll through the speed-dial locations.
• Enter the speed-dial location (000 to 999 or 0000 to 4999).
3. Press # or the ACCEPT menu button to dial the number.
Using Station Speed Dial
You can use Station Speed Dial to store phone numbers for your personal use. Other system
users do not have access to your Station Speed-Dial numbers.
Storing Station Speed-Dial Numbers
You can store up to 10 Station Speed-Dial numbers.
To store a Station Speed-Dial number:
1. With the handset on-hook, dial 383. PROGRAM STN SPD (0-9) OR SCROLL appears.
2. Do one of the following:
• Press
(Up) or
(Down) to scroll through the speed-dial bins.
• Enter the speed-dial bin (0 to 9).
Press # or the ACCEPT menu button to select the bin.
3. Enter the name of the speed-dial contact (up to 10 characters). For dialpad character
descriptions, see “Using the Dialpad Buttons to Enter Characters” on page 21.
4. Press # or the ACCEPT menu button to save the name.
5. Enter the extension number or external number. If you are storing an external number,
enter the Outgoing Call access code (default code is 8) before you enter the number. Do
not use hyphens or colons in stored speed-dial numbers.
6. Press # or the ACCEPT menu button to save the bin. STN SPD BIN # <number>
UPDATED appears.
Page 34
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Answering and Placing Calls
Dialing Station Speed-Dial Numbers
To dial a Station Speed-Dial number:
Do one of the following:
• Dial 382, and then enter the Station Speed Dial bin (0 to 9). The system dials the
number.
• Press
(Up) or
(Down) to scroll through the speed-dial bins, and then press
# to select the bin and dial the number.
NOTE
You can also program buttons to dial Station Speed-Dial numbers.
See “Assigning Speed-Dial Numbers to Programmable Buttons” on
page 36.
Deleting Station Speed-Dial Entries
To delete a Station Speed-Dial entry:
1. With the handset on-hook, dial 383. PROGRAM STN SPD (0-9) OR SCROLL appears.
2. Do one of the following:
• Press
(Up) or
(Down) to scroll through the speed-dial bins.
• Enter the speed-dial bin (0 to 9).
3. Press # or the ACCEPT menu button to select the bin.
4. Press
(Hold) repeatedly until the name is erased, and then press # or the
ACCEPT menu button to continue.
5. Press
(Hold) repeatedly until the number is erased, and then press # or the
ACCEPT menu button. STN SPD BIN # <number> UPDATED appears.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 35
Answering and Placing Calls
Assigning Speed-Dial Numbers to Programmable Buttons
You can assign Station or System Speed-Dial numbers to your programmable buttons.
NOTE
Before or after assigning the speed-dial number to a programmable button, make
sure the speed-dial number has either a Station Speed Dial bin or System Speed
Dial location assigned to it. For System Speed Dial numbers, numbers are preassigned to the System Speed Dial locations (000 to 999 or 0000 to 4999) by your
system administrator. Therefore, you just need to choose a System Speed Dial
location that you want to use (see “Using System Speed Dial” on page 34 for
details). For Station Speed Dial numbers, you must manually store numbers in the
Station Speed Dial bins (0 to 9). See “Storing Station Speed-Dial Numbers” on
page 34.
To program a Station Speed-Dial button:
1. With the handset on-hook, dial 397. PRESS THE BUTTON TO PROGRAM appears.
2. Press the feature button that you want to program as a speed-dial button.
3. Dial 382.
4. Do one of the following:
• Press
(Up) or
(Down) to scroll through the speed-dial bin.
• Enter the speed-dial bin (0 to 9), or select the menu button designation from the
display.
To program a System Speed-Dial button:
1. With the handset on-hook, dial 397. PRESS THE BUTTON TO PROGRAM appears.
2. Press the feature button that you want to program as a speed-dial button.
3. Dial 381.
4. Do one of the following:
• Press
(Up) or
(Down) to scroll through the speed-dial location.
• Enter the speed-dial location (000 to 999 or 0000 to 4999), or select the menu
button designation from the display.
Page 36
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Answering and Placing Calls
Using the Directory
You can use the Directory to find internal or external contacts or find and activate system
features. The directory uses Intelligent Directory Search (IDS), which is similar to the “text on 9
keys” (T9) predictive search feature used for mobile phones. The Directory has the following
three subdirectories:
• Intercom: Find and dial internal numbers.
• Outside: Find and dial external numbers listed in the company directory.
• Feature: Find and activate system features.
When searching the directory, dialpad buttons can represent several characters, as shown in
the following table. As you enter characters, the entries that best match the characters entered
appear. The system connects the character sequence to possible directory matches. For
example, to find the name “Jones,” dial 56637.
Button
Characters Represented
0
0
1
1
2
2ABCabcÇâäàåçÄÅá
3
3DEFdeféêëèÉ
4
4GHIghiïîìí
5
5JKLjkl
6
6MNOmnoôöòÖóñÑ
7
7QPRSqprs
8
8TUVtuvüûùÜú
9
9WXYZwxyzÿ
(Up)
Scroll to next entry
(Down)
Scroll to previous entry
*
Cancel search
#
Activate selection
(Hold)
Move the cursor to the left, deleting existing characters
See page 38 for detailed instructions on using the directory.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 37
Answering and Placing Calls
To search for a directory name or feature:
1. Dial 307, and then press one of the following:
• 1 for the IC directory.
• 2 for the Outside directory.
• 3 for the Feature directory.
• The Directory menu button (IC, OUTSIDE, or FEATURE).
2. Press the dialpad buttons to enter (up to 20) characters. See the table on page 37 for
dialpad button character descriptions.
(Up) or
3. Press
through the entries.
NOTE
(Down) or the >> (Next) or << (Previous) menu buttons to scroll
The IC directory may display two similar entries, one without an asterisk
and one with an asterisk. The entry without an asterisk is the primary
extension. The entry with an asterisk is a secondary extension.
4. Press # (or the menu button next to the entry) while the display shows the entry to dial a
number or activate a feature code.
Using Account Codes
Account codes record information for phone record reports. You may be required to enter
account codes when placing calls. Contact your system administrator for more information
about using account codes.
There are three types of account codes:
• Standard account codes: Automatically entered into the phone record report whenever
you place a call.
• Forced account codes: Entered before you can place an outside call.
• Optional account codes: Entered at any time during a call.
To enter an optional account code:
1. While off-hook, press
(Special), and then dial 390.
2. Enter the optional account code, and then press #.
To set an account code for all calls placed from your IP phone:
Dial 391 followed by the account code, and then press #. ACCOUNT CODE ACCEPTED
appears. This code is used for all calls made from your IP phone until it is disabled.
To disable the code:
Dial 391, and then press #. ACCOUNT CODE CLEARED appears.
Page 38
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Call Features
Call Features
The following sections describe call-related features.
Using Handsfree Mode
You can use Handsfree Mode to activate the speakerphone.
NOTES
The Ring Intercom Always feature prevents calls from being answered in
Handsfree Mode (see the following section).
You cannot use Handsfree Mode if you are using a headset, or if you have more
than one phone assigned to an extension number.
To use Handsfree Mode:
With the handset on-hook, dial 319. HANDSFREE MODE ON appears. Dial 319 again to
turn Handsfree Mode off.
Using Ring Intercom Always
If another extension has Handsfree Mode enabled for incoming internal calls (see the previous
section), you can use Ring Intercom Always to override Handsfree Mode on the extension,
requiring the called party to pick up the handset to answer your call.
To override Handsfree Mode for the current call:
1. Before you enter the extension number, press #. RING EXTENSION NUMBER appears.
2. Dial the extension number.
To use Ring Intercom Always to always send non-handsfree calls:
With the handset on-hook, dial 377. RING IC ALWAYS ON appears. Dial 377 again to
turn Ring Intercom Always off.
Using Mute
You can use Mute to temporarily turn off your microphone, preventing the other party on the call
from hearing you.
To mute or unmute the microphone:
While on a call, press
(Mute). MICROPHONE MUTE ON appears. When the
microphone is muted, the Mute button lamp is lit. Press
(Mute) again to unmute the
microphone.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 39
Call Features
Placing Calls On Hold
You can place calls on either Individual Hold or System Hold.
• Individual Hold: Places an internal or external call on hold at your IP phone.
• System Hold: Places an external call on hold in the system. You can then pick up the call
from any phone that indicates a flashing Call button for the call, including the IP phone that
placed it on hold.
To place a call on Individual Hold:
1. Press
(Hold). ENTER EXTENSION NUMBER appears.
2. Hang up or place another call.
To place an outside call on System Hold:
1. Press
(Special), and then dial 335. ENTER EXTENSION NUMBER appears.
2. Hang up or place another call.
To place a call on hold and answer a waiting call:
Press
(Hold), and then press the flashing IC or Call Key button.
To return to a call that is on hold:
Press
(Hold), and then lift the handset or press
HOLDING appears.
(Speaker). <Caller> WAS
Entering a Hookflash
Some telephone companies require you to enter a hookflash (a quick hang up and release) for
feature access.
To enter a hookflash:
While off-hook, press
Page 40
(Special), and then dial 330 or press the FLASH menu button.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Call Features
Transferring Calls
You can transfer calls to other extensions or external numbers. You can also transfer
conference calls. See “Transferring a Conference” on page 46 for more information.
Transferring Calls to Other Extensions
To transfer a call to another extension:
1. While on the call, press
(Transfer), and then enter the extension number.
2. Do one of the following:
• Wait for an answer, announce the call, and then hang up. If the extension is
unavailable, press the flashing IC or Call Key button to return to the caller.
• Hang up to transfer the call and disconnect the call from your IP phone.
NOTE
If your system administrator has enabled the Transfer-on-Connect
Allowed feature for your IP phone, you are automatically connected to
calls transferred to your extension after the transferring party hangs up.
If this option is turned off, you must press an IC or Call Key button to
answer calls transferred to your extension.
Transferring Calls to External Numbers
To transfer a call to an external number:
1. While on the call, press
(Transfer).
2. Press the Outgoing button or the Outgoing Call access code (the default code is 8) to
select an outside line.
3. Dial the phone number.
4. Do one of the following:
• Wait for an answer, announce the call, and then hang up. If the extension is
unavailable, press the flashing Call Key button to return to the caller.
• Hang up to transfer the call and disconnect the call from your IP phone.
Using Reverse Transfer
You can use Reverse Transfer (Call Pick Up) to answer calls that are ringing or holding at other
extensions. For example, if you receive a call while you are away from your desk, you can pick
up the call from another extension.
To use Reverse Transfer:
1. Lift the handset, and then press 4. ENTER EXTENSION NUMBER appears.
2. Dial the extension or hunt group number or press a DSS/BLF key where the call is
ringing or holding. The call is transferred to the IP phone you are using and you are
connected to the caller.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 41
Call Features
Viewing Your System Information
If you are on a call, you can temporarily view your user information (your user name and your
extension number.
To display your user information:
Press
(Special), and then dial 300.
Viewing Caller ID Information
If you are currently connected to an external caller with Caller ID, you can toggle between the
caller’s name and number. If the name is unavailable, CANNOT ACCESS FEATURE appears.
To show the outside party’s name/number:
Press
Page 42
(Special), and then dial 379.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Call Features
Forwarding Calls
You can use Manual Call Forwarding or System Forwarding to forward calls.
Manual Call Forwarding
The following table describes Manual Call Forwarding options.
Call Forward Feature
Call Forward All Calls
Description
Code/Menu Button
All incoming calls are forwarded.
355
ALL
Call Forward If No
Answer
All incoming calls are forwarded if
not answered. (The timer is set by
the system administrator.)
Call Forward If Busy
When your IP phone is busy, all
incoming calls are forwarded without
ringing.
Call Forward If No
Answer/Busy
All incoming calls are forwarded if
your IP phone is busy, or if you do
not answer.
356
NO ANSWER
357
BUSY
358
NO ANSWER/BUSY
To use Manual Call Forwarding:
1. Press the Forward button followed by the menu button designation, or dial the Manual
Call Forwarding feature code from the previous table. ENTER FORWARD DEST
appears.
2. Enter the extension number, or press the Outgoing button or the Outside menu button,
and then dial the telephone number. On the 5360 IP Phone, you can press the VOICE
MAIL menu button to forward calls to the Message Center (voice mailbox). FWD ALL
CALLS TO <number> appears.
To cancel a Call Forwarding request, do one of the following:
• Press Forward button, and then press the FWD OFF menu button.
• Enter a Forward feature code, and then press #.
NOTE
If the Configuration Assistant feature is enabled for your system, you can access a
voice guided configuration portal that provides easy-to-use, remote access to the
Call Forwarding feature. See page 51 for details.
System Forwarding
You can use System Forwarding to route calls based on the type of call and the idle or busy
status of your IP phone. You cannot program the System Forward destination. You can only turn
it on or off. Contact your system administrator for more information.
To turn System Forwarding on or off:
Dial 354. SYSTEM FORWARD ON appears. Dial 354 again to turn System Forwarding
off.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 43
Call Features
Using Dynamic Extension Express
When you enable Dynamic Extension Express on your IP phone, your incoming calls are
automatically routed to one or more preprogrammed associated destinations according to the
routing steps programmed for you.
Typically, your desk phone is configured to be your main extension. You may be programmed
for up to five associated destinations including:
• softphone
• home IP phone
• voice mail
• mobile phone
• home phone
Your desk phone, softphone, home IP phone and voice mail extensions are already
programmed in the system, so your system administrator can easily include them in your routing
steps. To include your mobile and home phone numbers in your routing steps, you will need to
provide these numbers to your system administrator.
Dynamic Extension Express also includes the Handoff feature, which includes the following
functions:
• Push: The Handoff “push” function allows you to move an active call from your main
extension, typically your desk phone, to an associated destination without disconnecting
audio. The push function is useful if you are leaving the work area, but want to remain
connected to an active call. The push function rings all associated destinations (except
voice mail) and you select which device to use to answer the call. When you answer the
call, you are immediately connected to the other parties at the new destination. When the
call is switching over to the new destination, there may be a momentary break in audio,
which may be noticeable to the other parties on the call.
• Pull: The Handoff “pull” function allows you to pull a call that was previously routed to your
mobile or home phone back to the main extension. The pull function is useful if you
answer a call on your mobile phone and then return to your desk. After you pull a call back
to the main extension, the call is connected immediately and you can then access system
features such as conference, hold, and transfer.
NOTE
The Handoff feature is only supported on your main extension, typically your
desk phone. However, if you share a desk phone with one or more coworkers
and your main extension is a phantom extension, you cannot use the Handoff
feature.
Dynamic Extension Express includes the following feature codes:
• Dynamic Extension Express On: 363
• Dynamic Extension Express Off: 362
• Dynamic Extension Express On/Off: 364
• Dynamic Extension Express – Handoff (push and pull): 388
The following call types do not follow Dynamic Extension Express:
• Hunt group calls
• Hunt group announcement/overflow calls
• Transfer recalls, Hold recalls, Conference recalls, and Attendant recalls
NOTE
Page 44
A recall occurs when a feature cannot be completed or the feature times out,
and the call returns to the originating extension. For example, a holding call
will recall the extension where it was placed on hold when the hold timer
expires.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Call Features
When you enable Dynamic Extension Express, your incoming calls are routed as specified by
the routing type programmed for you by your system administrator. The table below provides
descriptions for the default routing types.
Routing Type
Description
Mobile Twinning
Calls simultaneously ring your desk phone and mobile phone, before
going to voice mail.
Delayed Mobile
Twinning
Calls ring your desk phone first, and then ring both your desk phone and
mobile phone, before going to voice mail.
Check with your system administrator to see which routing type has been programmed for you.
Your administrator can modify these routing types by adding or removing routing steps, adding
or removing destinations, and changing the ring timers, if required.
To ensure that calls are routed correctly to your mobile and home phones, inform your system
administrator if either of these phone numbers change.
To enable Dynamic Extension Express:
Dial 363 or 364. PERSONAL ROUTING ON appears on the display.
To disable Dynamic Extension Express:
Dial 362 or 364. PERSONAL ROUTING OFF appears on the display.
To answer a call routed to your mobile or home phone:
1. Answer the call when it rings your IP phone. After you speak, the Dynamic Extension
Express prompt is played.
2. Do one of the following:
• Press # to accept the call.
NOTE
You do not need to wait for the prompt to accept the call. You can
accept the call immediately by pressing the # button.
• Press * to send the call to the voice mailbox associated with your main extension
(not your mobile phone or home phone voice mailbox). If you do not have a voice
mailbox, the “Press *...” prompt is not played and the call is routed to your main
extension.
If you hang up, the call continues to follow your programmed routing steps.
To use the Dynamic Extension Express – Handoff “push” feature:
1. While on an active call at your IP phone, press
(Special), and then dial 388.
HANDOFF IN PROGRESS appears on the display and the call rings all of your
associated destinations (except voice mail).
2. Press # to accept and answer the call at your mobile or home phone.
To use the Dynamic Extension Express – Handoff “pull” feature:
While on an active call on an associated destination device, dial 388. A confirmation tone
is played and the call is pulled back to your IP phone.
NOTE
If you enter the handoff feature code (388) and the display shows NO CALL TO
HANDOFF, the call cannot be handed off (see page 79).
To cancel the Dynamic Extension Express – Handoff feature:
While the handoff is in-progress, press
(Special), and then dial 388. HANDOFF
CANCELLED appears on the display for your main extension.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 45
Call Features
Placing Conference Calls
You can place a conference call with up to three internal or external parties (for a total of four
parties, including yourself).
To place a conference call:
1. While on the first call, press the Conference button to place the call on hold. CALL
NEXT PARTY TO CNF appears.
2. Place a call to the next conference party (for external calls, press the Outgoing button
or the Outgoing Call access code [8 is the default code], and then dial the number).
3. After the party answers, announce the conference, and then press the Conference
button to place the call on hold. If necessary, repeat this step to add the remaining
conference party.
4. Press the Conference button again or the CONNECT TO CNF menu button to start the
conference. CNF IN PROGRESS appears.
Adding a Conference Party
You can add a conference party during the conference.
To add a conference party:
1. Press the Conference button or the ADD PARTY menu button. This leaves the
conference parties connected.
2. Place a call to the party to be added to the conference, and then announce the
conference. Press the Conference button (twice) or the CONNECT TO CNF menu
button to add the party and rejoin the conference.
Transferring a Conference
You can transfer an existing conference to another extension.
To transfer a conference:
1. During the conference, press
(Transfer), and then dial the extension number.
2. Announce the conference (if desired), and then hang up. CONFERENCE TFR from
<name> appears on the called party’s display. The party must then press the flashing
Conference button to connect to the conference.
Dropping Out of a Conference
You can drop out of a conference and return to the conference later.
To drop out of a conference:
Press the Conference button or
(Hold), and then hang up. ENTER EXTENSION
NUMBER appears. This removes you from the conference but leaves the other parties
connected.
To return to the conference:
Press the flashing Call Key button. CONFERENCE WAS HOLDING appears, and you
are reconnected to the conference.
Page 46
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Call Features
Ending a Conference and Placing all Parties on Hold
You can end a conference and place all conference parties on Individual Hold, allowing you to
toggle between the held parties and speak to one party at a time.
To end a conference and place all parties on Individual Hold:
Press the Conference button, and then press
ON HOLD appears.
(Hold). CONFERENCE PARTIES
To toggle between the held callers:
Press
parties.
(Hold) twice for internal parties or the applicable Call Key button for external
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 47
Call Features
Using Record-A-Call
You can use Record-A-Call to record an ongoing call as a mailbox message.1 You can then
retrieve the message from your voice mailbox. The Record-A-Call feature stays active after the
other party hangs up, so you can add to the recorded call with your own message.
NOTE
Record-A-Call is not supported on peer-to-peer (P2P) calls. Contact your system
administrator for more information.
To use Record-A-Call:
1. While on a call, press
(Special), and then dial 385, or press the RECORD-A-CALL
menu button. REQUESTING RECORD-A-CALL appears.
2. Enter the voice mailbox number where you want the recording to be saved.
RECORD-A-CALL IN PROGRESS appears, and both you and the calling party hear a
confirmation tone (if enabled).
NOTE
If your system administrator assigns the Record-a-Call voice mailbox
destination, you do not need to enter the voice mailbox number.
To stop Record-A-Call:
Do one of the following:
• Press
(Special), and then dial 385.
• Press the CANCEL RECORDING menu button.
• Hang up.
Using Group Listen
You can use Group Listen to activate the speaker while you use the handset or headset to
continue speaking. This allows other people to hear the other party on the call while the other
party can only hear you (through the handset microphone). You cannot use Group Listen in
Handsfree Mode.
To use Group Listen:
While on a call, press
(Special), and then dial 312. GROUP LISTEN ON appears, and
you hear a confirmation tone. The other party does not hear the confirmation tone. Dial
312 again to turn Group Listen off.
1.
Page 48
This feature may or may not be enabled for your system.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Call Features
Using Call Logging
Your call logs are records of your most recent missed, received, and dialed calls. A maximum of
20 entries are stored in each call log.2
You can use Call Logging to:
• View recent call activity.
• View caller ID information.
• Return or redial calls.
To use Call Logging:
1. Dial 333 or the LOGS menu button.
2. Select one of the following options:
• Press 1 (MISS) or the MISSED CALLS menu button for missed calls.
• Press 2 (RCV) or the RECEIVED CALLS menu button for received calls.
• Press 3 (DL) or the DIALED CALLS menu button for dialed calls.
• Press 4 (CLR) or the CLEAR LOGS menu button to clear all entries.
3. Press
(Up) or
through the entries.
(Down) or the >> (Next) or << (Previous) menu buttons to scroll
The display shows the party’s name and the extension or outside number (if available)
and the date and time.
If no Caller ID information is available, UNKNOWN CALLER appears.
To return a call or redial a number listed in a call log:
Press # or the CALL NOW menu button while the display shows the number.
To delete individual call log entries:
Press 0 or the DELETE menu button to delete the displayed entry, or press the DEL ALL
menu button to delete all entries in the current call log.
2.
This feature may or may not be enabled for your system.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 49
Call Features
Using Secondary Extension Buttons
Secondary Extension buttons must be programmed by your system administrator. You can use
programmable buttons as “secondary extensions.” Secondary Extensions are assigned to other
extensions in the system (primary extensions). Because Secondary Extension buttons are
programmed by the system administrator, you cannot change the buttons (for example, assign
features to the buttons).
When programmed, you can use Secondary Extension buttons to:
• Place an internal call to the primary extension.
• View the call activity at the primary extension.
• Transfer calls to the primary extension.
• Answer a call that is ringing or holding on any Call Key button at the primary extension.
The system administrator must set up the Call Key buttons for internal calls or
you cannot use Secondary Extensions at the primary extension.
NOTES
Page 50
You can use Secondary Extension buttons to notify you when a given number
of calls are waiting at the primary extension.
If a Secondary Extension button is flashing (the primary extension has an
incoming call), you can press # before pressing the flashing Secondary
Extension button to call the primary extension and not answer the incoming
call.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Call Features
Using Configuration Assistant
If Configuration Assistant is enabled for your system, you can access this voice guided
configuration portal that provides easy-to-use, remote access to the following phone
configuration options:
• Dynamic Extension Express (see below)
• DND (see page 52)
• Manual Call Forwarding (see page 53)
NOTE
You need a Configuration Assistant extension number to use this feature. Contact
your system administrator for more information.
Changing Your Station Password
Before using Configuration Assistant, Mitel recommends that you change your default Station
password to something more secure.
To change your Station password:
1. Dial 392. ENTER PASSWORD appears.
2. Enter your current password (the default password is your extension number), followed
by #. CHANGE PASSWORD TO appears.
3. Enter the new password followed by #. VERIFY PASSWORD appears.
4. Enter the new password again followed by #. DATABASE UPDATED appears.
To change the password from another phone, see “Changing Your Station Password” on
page 56.
Accessing Configuration Assistant
Follow the instructions below to access Configuration Assistant.
To access Configuration Assistant:
1.
Access the Configuration Assistant extension number from inside or outside the system
by:
• dialing it from any phone in the system.
• being transferred to it.
• dialing it from automated attendant, voice mail, or DISA.
2.
Do one of the following:
• If calling from your main desktop phone, proceed to step 3..
• If calling from someone else’s main desktop phone that is designated as a
Configuration Assistant user, press the Star button (*), and then enter your
extension number.
• If calling from a phone that is not designated as a Configuration Assistant user,
enter your extension number.
• If transferred to Configuration Assistant or if calling Configuration Assistant from
outside the system, enter your extension number.
3.
Enter your Station password, and then press #.
You may now change the settings for any of the following features:
• Dynamic Extension Express (see page 52)
• DND (see page 52)
• Manual Call Forwarding (see page 53)
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 51
Call Features
Changing the Dynamic Extension Express Settings
NOTE
This feature is available only if the authenticated extension is identified as a
Dynamic Extension Express (DEE) user. See “Using Dynamic Extension Express”
on page 44 for more information.
To change the DDE settings using Configuration Assistant:
1.
Access Configuration Assistant as described in “Accessing Configuration Assistant” on
page 51.
2.
Follow the voice prompts to change your DEE status (on or off) or program a mobile
phone number. When this option is selected, Configuration Assistant first states whether
DEE is currently enabled or not (for example, “Dynamic extension is enabled”), and then
offers the following DEE functions:
• Enable (only if DEE is disabled)
• Disable (only if DEE is enabled)
• Program mobile phone number [you do not have to enter the Outgoing feature
code (8)]
3.
Hang up, or press the Star button (*) to return to the main menu.
Changing the DND Settings
See “Using Do-Not-Disturb (DND)” on page 59 for more information about using DND.
To change the DND settings using Configuration Assistant:
1.
Access Configuration Assistant as described in “Accessing Configuration Assistant” on
page 51.
2.
Follow the voice prompts to change your DND status (on or off). There is no option to
provide a specific DND status message. When this option is selected, Configuration
Assistant first states whether DND is currently enabled or not (for example, “Do-NotDisturb is currently disabled”), and then offers the following DND functions:
3.
Page 52
o
Enable (only if DND is disabled)
o
Disable (only if DND is enabled)
Hang up, or press the Star button (*) to return to the main menu.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Call Features
Changing the Manual Call Forwarding Settings
See “Manual Call Forwarding” on page 43 for more information about Manual Call Forwarding.
To change the Manual Call Forwarding settings using Configuration Assistant:
1.
Access Configuration Assistant as described in “Accessing Configuration Assistant” on
page 51.
2.
Follow the voice prompts to change your manual call forwarding status (on or off). There
is no option to provide a specific call forwarding condition, such as no answer or busy.
When this option is selected, Configuration Assistant first states whether call forwarding
is currently enabled or not (for example, “Call Forwarding is enabled”) and then offers
the following forwarding functions:
• Forward calls to voice mail
• Forward calls to an internal extension number
• Forward calls to an external phone number [you do not have to enter the Outgoing
feature code (8)]
• Disable (only if Call Forwarding is enabled)
3.
Hang up, or press the Star button (*) to return to the main menu.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 53
Call Features
Using Remote Programming
If the Configuration Assistant feature is enabled for your system, Mitel recommends that you
use Configuration Assistant instead of the Remote Programming feature described in this
section. Configuration Assistant offers an enhanced, voice guided configuration portal that
provides easy-to-use, remote access to the Call Forwarding, Dynamic Extension Express, and
DND features. See page 51 for using Configuration Assistant.
To use Remote Programming to access these features from another system phone or an
external phone, follow the instructions in this section. 3
NOTE
A Direct Inward System Access (DISA) number is required to use Remote
Programming from an external phone. Contact your system administrator for more
information.
Changing the Dynamic Extension Express Settings
See “Using Dynamic Extension Express” on page 44 for more information about Dynamic
Extension Express.
To enable Dynamic Extension Express using Remote Programming:
1. Do one of the following:
•
Call your DISA number (provided by the system administrator). If necessary, enter
your DISA password.
•
Use any phone on the system.
2. Dial 359.
3. Enter your extension number.
4. Enter your Station password followed by #. See page 51 for details on setting up a
Station password for your extension.
5. Dial 363 (Dynamic Extension Express On).
To disable Dynamic Extension Express using Remote Programming:
Follow steps 1 - 4 above, dial 362 (Dynamic Extension Express Off), and then hang up.
3.
Page 54
This feature may or may not be enabled for your system.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Call Features
Changing the DND Settings
See “Using Do-Not-Disturb (DND)” on page 59 for more information about using DND.
To turn on DND using Remote Programming:
1. Do one of the following:
• Call your DISA number (provided by your system administrator). If necessary, enter
your (DISA) password.
• Use any phone on the system.
2. Dial 359.
3. Enter your extension number.
4. Enter your Station password followed by #. See page 51 for details on setting up a
Station password for your extension.
5. Dial 370.
6. Enter the DND message number (01 to 20), and then enter the second-line message
text (if applicable).
To turn off DND using Remote Programming:
Follow steps 1 through 4 above, and then dial 371.
Changing the Manual Call Forwarding Settings
See “Manual Call Forwarding” on page 43 for more information about Manual Call Forwarding.
To turn on Manual Call Forwarding using Remote Programming:
1. Do one of the following:
• Call your DISA number (provided by your system administrator). If necessary, enter
your DISA password.
• Use any phone on the system.
2. Dial 359.
3. Enter your extension number.
4. Enter your Station password followed by #. See page 51 for details on setting up a
Station password for your extension.
5. Dial one of the following Call Forwarding feature codes:
• 355 (All)
• 356 (No answer)
• 357 (Busy)
• 358 (No Answer/Busy)
6. Enter either an extension number or 8 followed by a phone number.
To turn off Call Forwarding using Remote Programming:
Dial 355, and then hang up.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 55
Call Features
Changing Your Station Password
You can use Remote Programming to change the Station password. See page 51 for details on
setting up a Station password for your extension.
To change your Station password using Remote Programming:
1. Do one of the following:
• Call your DISA number (provided by your system administrator). If necessary, enter
your DISA password.
• Use any phone on the system.
2. Dial 359.
3. Enter your extension number.
4. Enter your password followed by #.
5. Dial 392.
6. Enter the new password followed by #.
7. Enter the new password again followed by #.
Page 56
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Messages
Messages
This section describes the following system messaging features:
• Inter-station messages: Inter-station messages are alerts sent to your IP phone by other
internal parties, notifying you to contact the party who left the message. The
(Message) button and Message/Ring Indicator flash to notify you of the new
message. You can then either delete the message or reply to the message, which
automatically places a call to the party who left the message.
• Do-Not-Disturb (DND) messages: Messages that other internal parties see when your IP
phone is in DND. See “Using Do-Not-Disturb (DND)” on page 59.
• Reminder messages: Messages that you can use to notify yourself of upcoming
appointments, meetings, and so on. See “Using Reminder Messages” on page 60.
• Pages: Announcements sent over phone speakers or external speakers. See “Paging
Other System Users” on page 61.
• Voice messages: System voice mail messages.
NOTE
Because a variety of voice mail products work with the 5000 CP, this guide
does not include voice mail instructions. For voice mail instructions, refer to
the voice mail user guide for your system. For example, refer to the
Enterprise Messaging, Basic Voice Mail, and Embedded Voice Mail Card
User Guide, part number 835.3205, or the Mitel NuPoint Unified Messaging
User Guide on the Mitel Web site (http://edocs.mitel.com). Contact your
system administrator for more information about your voice mail system.
Leaving Messages at Other Extensions
You can leave inter-station or voice mail messages for other internal parties.
To leave an inter-station or voice message for a busy IC extension:
1. Press
(Message) or the LEAVE MESSAGE menu button. HANG UP OR WAIT FOR
MSG CENTER appears.
2. Do one of the following:
• Hang up to leave an inter-station message. MESSAGE LEFT FOR <name>
appears.
• Stay on the line to connect to the message center (usually voice mail).
To leave an inter-station message without placing an internal call:
1. Dial 367 (Leave Message), or press
(Message), and then press the LEAVE
MESSAGE menu button. LEAVE MESSAGE ON EXTENSION appears.
2. Enter the extension number. MESSAGE LEFT FOR <name> appears.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 57
Messages
Viewing and Responding to Messages
When you have waiting messages, the
(Message) button and Message/Ring Indicator flash
and the display shows the number of waiting messages.
NOTE
If your handset or speakerphone is off-hook when you view an inter-station
message, you automatically call the party who left the message.
The display shows new messages as follows:
• Inter-station messages sent by other internal parties are indicated by the party’s
programmed user name.
• Voice messages are indicated by FROM MBOX <your extension number>.
To view or respond to messages:
1. With the handset on-hook, press
(Message) or the VIEW MESSAGE menu button.
Messages are displayed as first in/first out. If there is more than one message, you can
repeatedly press
(Message) to scroll through the messages.
2. When the desired message is displayed, press #, or lift the handset for privacy, and then
press # to respond. [If your handset is off-hook and you press
(Message), you
automatically place a call to the party or message center that left the message.]
Canceling Messages Left at Other Extensions
You can cancel messages left at other extensions.
To cancel a message left at another extension:
1. Dial 366 or press
(Message), and then press the CANCEL MESSAGE menu
button. CANCEL MESSAGE ON EXT # appears.
2. Enter the extension number where you left the message. MESSAGE CANCELED FOR
<name> appears.
Deleting Waiting Inter-Station Messages
You can delete waiting inter-station messages.
NOTE
To delete waiting voice messages, you must connect to your voice mailbox.
To delete waiting inter-station messages:
1. Press
(Message) or the VIEW MESSAGE menu button. MSG <message
information> appears.
2. Press * or the DELETE menu button to delete the displayed message.
Page 58
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Messages
Using Do-Not-Disturb (DND)
You can use DND to stop calls and pages to your extension. When activated, internal calling
parties see your selected DND message. DND does not block queue callbacks, recalls, and
incoming external calls. The following table shows the 20 default DND messages. If your
system administrator changes your DND messages, you can record the new messages in the
“New Message” column for reference.
Default Message
Code
New Message
Code
Default Message
01
Do-Not-Disturb
11
Out of Town ‘Til
02
Leave a Message
12
Out of Office
03
In Meeting Until
13
Out Until
04
In Meeting
14
With a Client
05
On Vacation/
Holiday ’Til
15
With a Guest
06
On Vacation/
Holiday
16
Unavailable
07
Call Me At
17
In Conference
08
At the Doctor
18
Away from Desk
09
On a Trip
19
Gone Home
10
On Break
20
Out to Lunch
New Message
You can enter a second line of text (up to 20 characters) for DND messages. For example, if
you select IN MEETING UNTIL, you can enter “3:30” on the second line. When other internal
parties try to call you, their displays show “IN MEETING UNTIL 3:30.”
To turn on DND:
1. Press the DND button. SELECT DND MSG # (01-20) appears.
2. Do one of the following:
• Press
(Up) or
(Down) to scroll through the messages.
• Enter the two-digit number for the DND message from the preceding table.
• Press the SCROLL menu button, and then press the PREVIOUS or NEXT menu
buttons to scroll through the list.
3. If applicable, enter the additional text for the DND description. See “Using the Dialpad
Buttons to Enter Characters” on page 21 for dialpad character descriptions.
4. Press
(Speaker) or the ACCEPT menu button.
To turn off DND:
Press the DND button, or press the DND menu button, and then press DND OFF. DONOT-DISTURB OFF appears.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 59
Messages
Using Reminder Messages
You can use Reminder messages to alert you at a selected time, up to 24 hours in advance. At
the selected time, the Reminder message signals you with eight short tones and your display
shows the message, even if you are on a call.
The following table shows the 20 default Reminder messages. If your system administrator
changes your Reminder messages, you can record the new messages in the “New Message”
column for reference.
Code
Default Message
New Message
Code
Default Message
01
Meeting
11
Call Engineering
02
Staff Meeting
12
Call Marketing
03
Sales Meeting
13
Call Accounting
04
Cancel Meeting
14
Cancel DND
05
Appointment
15
Cancel Call Fwd
06
Place Call
16
Take Medication
07
Call Client
17
Make Reservation
08
Call Customer
18
Review Schedule
09
Call Home
19
Lunch
10
Call Corporate
20
Reminder
New Message
To set a Reminder message:
1. With the handset on-hook, dial 305. SELECT REMINDER MESSAGE # (01-20) appears.
2. Do one of the following:
• Enter the two-digit number for the Reminder message from the preceding table.
• Press
(Up) or
(Down) to scroll through the messages.
3. Press # or the ACCEPT menu button to select the message.
4. Enter the time you wish to receive the message in hours and minutes (for example, 0900
or 900 for 9:00). Then press #. The display shows the Reminder message state.
If your system is set for 24-hour format, enter the applicable time (1400 = 2:00 P.M.).
If your system is set for 12-hour format, press 1 for A.M. or 2 for P.M.
To cancel all Reminder message requests:
With the handset on-hook, dial 306. REMINDER MSGS CANCELED appears.
To clear a received Reminder message:
With the handset on-hook, press *.
Page 60
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Messages
Paging Other System Users
You can place page announcements through phone speakers or external speakers (if
applicable). Your system may use page zones to prevent announcements from transmitting
through every phone in the system. Each page zone contains a different combination of
extensions and external paging equipment.
Contact your system administrator for page zone information. You can use the following table to
save the page zone information for future reference.
Page Zone Name
Number
Description
Placing a Page Announcement
The following instructions describe how to place a page announcement.
To place a page announcement:
1. Press 7.
2. Enter the page-zone number (0 to 9).
3. Wait for the tone, make your announcement, and then hang up.
Enabling or Disabling the Page Feature
You can enable or disable the Page feature for your extension. If your extension is assigned to
more than one page zone, the Page on/off feature code enables or disables your extension for
all pages zone (you cannot select individual zones).
To enable or disable paging for your IP phone:
Dial 325 to enable paging. PAGE RECEIVE ON appears. Dial 325 again to disable
paging.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 61
Hunt Groups
Hunt Groups
Hunt groups are groups of internal parties (agents) who share a common (hunt group)
extension number. Calls can either be placed to the hunt group (using the hunt group extension
number) or to a specific agent (using the agent’s extension number). Hunt groups are
programmed by the system administrator.
Hunt groups types are either “UCD” or “ACD.”
• UCD Hunt Groups: Uniform Call Distribution (UCD) agents do not log in to the hunt group
to receive calls.
• ACD Hunt Groups: Automatic Call Distribution (ACD) agents log in to the ACD hunt group
to receive calls. Calls are distributed by either Agent IDs or extensions:
o
Agent IDs: Each agent is assigned an Agent ID number for logging in to the hunt group
(see the next section). Hunt group calls are distributed to logged-in agents according to
their Agent ID number instead of their extension number. Agents can log in to any ACD
hunt group phone.
o
Extensions: Hunt group members do not use Agent IDs, and calls are distributed to
phones where the agents are logged in.
Logging in to ACD Hunt Groups
You must log in to an ACD hunt group to receive hunt group calls. To stop calls, you either log
out of the ACD hunt group or divert calls. See “Diverting Hunt Group Calls” on page 65.
Only one agent can be logged in to a phone.
NOTES
If the ACD Agent ID Automatic Connect option is enabled for your hunt group and
you are using a headset, you are automatically connected to waiting calls when you
log in. The first call you receive after you log in rings until you answer it; however,
you are automatically connected to subsequent calls.
To log in to or out of all ACD hunt groups in which you are a member:
Dial 328 to log in to ACD hunt groups followed by your Agent ID, if necessary. AGENT
LOGGED INTO ALL ACDS appears. Dial 328 again to log out of all ACD hunt groups.
To log in to one or more ACD hunt groups:
1. Dial 326. AGENT LOGIN ACD HG # appears.
2. Do one of the following:
• Enter the ACD hunt group number.
• Press # to log in to all of your ACD hunt groups.
The display shows AGENT LOGIN AGENT ID.
3. Enter your Agent ID (if applicable), or press # if you do not have an agent ID. The
display shows the log in status for one or all hunt groups.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 63
Hunt Groups
Logging out of ACD Hunt Groups
You can log out of all ACD hunt groups at once or log out of each hunt group one at a time.
To log out of one or more ACD hunt group:
Do one of the following:
• Dial 328 to log out of all of your ACD hunt groups. The display shows AGENT
LOGGED OUT OF ALL ACDS.
• Dial 327 to log out of one hunt group at a time.
If you were logged in to only one hunt group, the display shows AGENT LOGGED
OUT OF HUNT GROUP <number>.
If you were logged in to more than one hunt group, the display shows AGENT
LOGOUT HG #. Enter the extension number of the ACD hunt group.
Stopping the ACD Hunt Group Wrap-up Timer
Each time you end an ACD hunt group call, a wrap-up timer starts. The default wrap-up time is
15 seconds. Your system administrator can change the wrap-up timer settings.
Until this timer expires, you will not receive another hunt group call; however, you can stop the
wrap-up timer to allow calls to your extension.
To stop the wrap-up timer:
With the handset on-hook, dial 329. The display shows ACD WRAP-UP TERMINATED.
Page 64
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Hunt Groups
Other Hunt Group Features
The following features can be used by ACD or UCD hunt groups.
Requesting Agent Help
You can use Agent Help to request help from a designated “Agent Help Extension” (usually your
supervisor) during a call. When your request call rings at the Agent Help Extension, the
supervisor can join the call or reject the request.
NOTE
Agent Help is not supported on peer-to-peer (P2P) calls. Contact your system
administrator for more information.
To use Agent Help:
1. While you are on a hunt group call, press
(Special), and then dial 375.
If you hear repeating tones, one of the following has occurred:
• The feature is not available at your IP phone.
NOTE
• You already have four parties in your call.
• Not enough system circuits are currently available.
• The Agent Help Extension is in DND.
2. If not preprogrammed, dial the Agent Help extension number.
If the Agent Help Extension accepts the call, AGENT HELP IN PROGRESS appears.
If the Agent Help Extension rejects the call, AGENT HELP REJECTED appears.
Diverting Hunt Group Calls
You can temporarily divert hunt group calls, preventing hunt group calls to your extension.
To divert hunt group calls:
Dial 324 to divert calls. The display shows the feature state DIVERT HUNT GROUP
CALLS. Dial 324 again to program your IP phone to accept calls.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 65
Hunt Groups
Hunt Group Supervisor Features
The following features can be used by hunt group supervisors only.
Accepting or Rejecting Agent Help Calls
Supervisors can accept or reject Agent Help calls.
To accept an Agent Help request:
Answer as usual. Your microphone is automatically muted.
To reject an Agent Help request:
Dial 376 or press the REJECT HELP menu button. AGENT HELP REJECTED appears.
Monitoring Calls
You can use Station Monitor to connect to a hunt-group call and hear both parties, but you
cannot be heard by either one. Station Monitor stops if the hunt group member terminates or
transfers the call. You can barge-in to or “steal” monitored calls, as described in the following
sections. You can also record the call. See “Using Record-A-Call” on page 48 for more
information about recording calls.
NOTE
Station Monitor is not supported on peer-to-peer (P2P) calls. Contact your system
administrator for more information.
To use Station Monitor:
Dial 321 or press the SIL MONITOR menu button, and then enter the extension number.
MONITORING EXT <number> appears. Monitored hunt group members may hear an
“activation tone” when the feature is activated.
Stealing Hunt Group Calls
While monitoring a hunt group call, you can “steal” the call from the hunt group member, which
disconnects the call from the agent and transfers the call to your extension.
To steal a hunt group call:
Dial 387 or press the STEAL menu button. CALL STOLEN FROM EXT <number>
appears.
Page 66
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Hunt Groups
Using Barge-In
While monitoring a hunt group call, you can use Barge-In to join the call.
To monitor and/or barge in on a call:
1.
To use the speakerphone: While on hook, dial 321. You hear a confirmation tone.
ENTER EXT TO MONITOR appears.
To use the handset: Lift the handset, and then dial 321. You hear a confirmation tone.
ENTER EXT TO MONITOR appears.
2.
Dial the extension number (or press the lit station speed-dial or DSS/BLF button) of the
station to be monitored. You are automatically connected to the call. MONITORING
(extension number) appears.
3.
While silent monitoring a call, you have the following options:
•
To barge in on a call, dial 386 or press the BARGE-IN menu button. BARGE-IN IN
PROGRESS appears. While on a call, you can monitor, record, or steal the call by
entering the appropriate feature code or by pressing the appropriate menu button.
To return to silent monitoring of the call, dial 386 again or press the MONITOR
menu button.
To record the call, dial 385 or press the RECORD CALL button.
• To record a call, dial 385 or press the RECORD menu button. MONITORING
(extension number) appears. While on a call, you can monitor or steal the call by
entering the appropriate feature code or by pressing the appropriate menu button.
To stop recording the call, dial 385 again or press the STOP RECORDING menu
button.
•
To steal a call, dial 387 or press the STEAL menu button. CALL STOLEN FROM
(extension number) appears. The hunt group member’s display shows CALL
STOLEN BY (extension number). After the supervisor steals the call, the call
becomes a regular call. While on a call, you can record the call by dialing 385 or by
pressing the RECORD menu button.
•
To join and record a call, dial 386 or press the JOIN AND RECORD menu button,
and then dial 385. BARGE-IN IN PROGRESS appears. While on a call, the
supervisor can monitor, stop recording, or steal the call by entering the appropriate
feature code, or by pressing the appropriate menu button.
To stop recording the call, dial 385 again, or press the MONITOR or STOP
RECORDING menu button.
4.
To terminate any of the features: If off hook, hang up or enter the specific feature code
of the feature you want to terminate. If on hook, press the Speaker button or enter the
specific feature code of the feature you want to terminate.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 67
Cordless Devices
Cordless Devices
You can use the cordless handset and cordless headset to move around within your office or
adjacent offices. The cordless headset and handset are optional accessories, ordered
separately. For more information, contact your system administrator or local Mitel provider. Both
cordless devices connect to your IP phone through the cordless module, which attaches to the
back of the IP phone. The cordless headset rests and recharges in a headset cradle that
attaches to the side of the IP phone. The cordless handset recharges in the handset cradle.
The Cordless Devices Application provides access to the configuration settings and information
screens that apply to the cordless module and accessories. For more information, see “Pairing
the Cordless Module and Devices” on page 71.
The cordless module is shown here. The IP phone features are explained below.
1
5
2
3
4
Feature
Function
1 – Cordless Module
Attached to the back of the IP phone, the module contains a
light-emitting diode (LED) indicating that a cordless device is
in use; also indicates the pairing of module and a cordless
device.
2 – Cordless Headset
Cordless handsfree operation for calls. If you are using the
cordless headset, you do not need to use the handset.
3 – Cordless Headset Charging
Cradle
Provides power to recharge the cordless headset battery.
4 – Cordless Handset Charging
Cover
Provides power to recharge the cordless handset battery.
Replaces the cover supplied with the IP phone for corded
handsets.
5 – Cordless Handset
Cordless operation for handset calls. (You can transfer from
the IP phone handset to the cordless headset at any time.)
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 69
Cordless Devices
Cordless Module
The cordless module is shown here.
CAUTION
Phone Damage Hazard. Attempting to remove the back plate on the IP phone to install the
cordless module before disconnecting the IP phone power supply may damage the IP
phone. For information about installing the cordless module, refer to the installation documentation that is shipped with the unit.
1
2
Feature
Function
1 – Cordless Module pairing button
Initiates pairing between the cordless module and a
cordless device.
2 – Cordless Headset Cradle cable
Connects to the cordless module to provide power
to the charging cradle.
Handset and Headset Combinations
The following combinations of corded and cordless headset and handset are supported on the
5360 IP Phone:
• Corded handset only
• Corded headset only
• Corded handset and corded headset
• Cordless handset only
• Cordless headset only
• Cordless handset and cordless headset
• Corded handset and cordless headset
• Corded headset and cordless handset
Page 70
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Cordless Devices
Pairing the Cordless Module and Devices
Before using the cordless handset or headset, each device must establish communication with
the cordless module using a procedure called pairing.
An IP phone can have only one cordless handset and one cordless headset.
A cordless handset or headset can be paired with only one IP phone at a time.
NOTES
Pairing a new cordless handset or headset with the IP phone overwrites the
configuration of any previous handset or headset.
Pairing cannot be performed when the cordless device is already in use.
To pair a cordless device:
1.
Ensure that the battery of the cordless device to be paired is at least partially charged.
2.
Press and hold down the pairing button on the back of the cordless module
(see page 70) for five seconds to activate phone pairing mode. The LED on the cordless
module blinks. The Cordless Devices application opens on the IP phone and prompts
you to press the pairing button on the cordless device.
3.
Press and hold down the hookswitch on the cordless handset or headset for five
seconds to activate the device pairing mode. The LED on the cordless device blinks.
After a moment, the Cordless Devices application displays information for the device to
be paired.
4.
Press Yes to confirm pairing. The Cordless Devices application confirms the pairing by
displaying the paired device name and its battery level indicator and the number of
devices paired.
5.
Press Close to exit.
To unpair a cordless device:
1.
Press
2.
Press the device name you want to unpair. The information screen for the selected
device appears.
(Applications), and then press Cordless Devices.
3.
Press Unpair this Device. If the device is in use, an error message appears. Otherwise,
the device is unpaired, removed from the display, and can no longer be used to interact
with the IP phone.
4.
Press Close.
The cordless module has a blue LED that indicates the current status of the module. The
handset is blinking, when the LED is on and off for an equal amount of time.
Blue LED
Function
Solid
Audio is active between the module and either the
handset or headset.
Blinking
Pairing mode is active or a firmware upgrade is in
progress.
Off
No audio is active.
Solid for two seconds
Pairing is successful.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 71
Cordless Devices
Using a Cordless Device as a Remote Control
When not being used to talk, the cordless handset/headset buttons can act as a remote control
device to change display contrast, volume, and mute settings on the host IP phone. For
example, in a remote handsfree conference setting, you can use the Volume and Mute buttons
on a cordless device to adjust speaker levels and mute the microphone on an IP phone that is
not within his reach.
Alerting Tones and LEDs
The cordless devices provide the following alerting tones:
Feature
Function
Mute key on cordless device ON/OFF
Two-pitch tone occurs immediately. Reminder tone
occurs 30 seconds after activation and then
regularly until deactivated
Mute key on phone ON/OFF
No immediate tone. Reminder tone occurs 30
seconds after activation and then regularly until
deactivated.
Low battery (within 10 minutes left)
Three beeps and 20 second pause repeated three
times.
Low battery (within 2 minutes left)
Three rapid beeps and 1.5 second pause repeated
three times.
Out of range
Repetitive 3-pitch tone until you are back in range.
NOTES
Audio indications are heard in the handset only when it is in use, and may interrupt
voice transmission.
If you are out of range for more than 10 seconds, any call that is in progress is
dropped and not recovered.
Low Battery Level
When the battery of a cordless device reaches a near-critical level, the IP phone displays a
warning. Until the battery is recharged (or until it becomes fully discharged), the warning is
repeated at each new call. To continue with a call while charging the cordless device, switch to
speakerphone and then cradle the cordless device.
Page 72
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Cordless Devices
Cordless Handset
The cordless handset, shown below provides office mobility, allowing you to place and answer
calls while away from your desk. Replacing the standard corded handset, the cordless handset
contains a chargeable battery that charges in the handset cradle when not in use. To use the
cordless handset, you must pair the handset with the IP phone. For more information, see
“Pairing the Cordless Module and Accessories” on “Pairing the Cordless Module and Devices”
on page 71.
Cordless Handset Features
Cordless handset elements are shown in the following table.
Feature
1 – Cordless Handset LED
Function
Blue: LED indicating the status of the handset.
Green: LED indicating the status of the handset
battery.
For more information see page 74.
2 – Hookswitch and pairing button
Lifting the handset from the cradle activates the
handset. If the handset is already out of the cradle,
pressing the hookswitch takes the handset off-hook.
Pressing the hookswitch again returns it to on-hook.
Pressing the hookswitch while on a speakerphone
all, moves the call to the cordless handset.
3 – Mute button
Mute allows you to turn the microphone off during a
call.
4 – Volume Up and Down button
Up and Down buttons provide volume control for the
ringer and handset/headset.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 73
Cordless Devices
Answering Calls
The following instructions describe how to answer a call.
To answer a call:
Do one of the following:
• Lift the cordless handset.
• If the handset is already out of the cradle, press the hookswitch button on the
handset.
Hanging Up
If you are out of range for more than 10 seconds, any call that is in progress is dropped and not
recovered.
To hang up:
Do one of the following:
• Replace the cordless handset in the cradle.
• Press the hookswitch button on the handset.
Cordless Handset LEDs
The handset has two LEDs:
• Blue – indicates the operational status of the handset.
• Green – indicates the status of the electrical charge of the battery.
The handset is blinking, when the LED is on and off for an equal amount of time. The handset is
winking, when the LED is on for a short period of time and off for a longer period of time.
LED Color
Blue
LED State
Indicates:
Solid
Handset is muted.
Blinking
Handset is in pairing mode.
Winking
Active audio path between handset and
module.
Off
No audio path between handset and module.
Battery is dead.
Green
NOTE
Page 74
Solid
Battery is fully charged.
Blinking
Battery is charging.
Off
When handset is cradled and the LED does
not flash or illuminate, this indicates an
absence of battery power. During the first
30 – 60 minutes that the light is off, the
battery may be trickle charging. If that is the
case, the LED resumes normal behavior
within that 60–minute period. If the LED
remains off for more than 60 minutes, then
either the battery is no longer chargeable or
there is a problem in the charging circuit.
It is normal for the handset LED to cycle between blinking and solid as battery
charge is maintained.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Cordless Devices
Cordless Headset
The cordless headset offers the same capability as the cordless handset to make and answer
phone calls away from your desk, while adding the convenience of hands-free operation.
When not in use, the cordless headset sits in the headset charging cradle. For more information
on alerting tones and LEDs, see “Alerting Tones and LEDs” on page 72.
To use the cordless headset, you must pair the headset with the IP phone. For more
information, see “Pairing the Cordless Module and Devices” on page 71.
Cordless Headset Features
The cordless headset is shown here.
41
3
2
5
1
1 – Microphone
4 – Volume control
2 – Boom arm
5 – Hookswitch and pairing button
3 – Linked Indicator (LED)
Answering Calls
The following instructions describe how to answer a call.
To answer a call:
Do one of the following:
• Lift the cordless headset from the cradle.
• If the headset is already out of the cradle, press the hookswitch button on the
headset.
Hanging Up
If you are out of range for more than 10 seconds, any call that is in progress is dropped and not
recovered.
To hang up:
Do one of the following:
• Replace the cordless headset in the cradle.
• If the headset is already out of the cradle, press the hookswitch button on the
headset.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 75
Cordless Devices
Cordless Headset LEDs
There are two LEDs associated with the cordless headset:
• Blue – Indicates the operational status of the headset
• Green – Indicates the status of the electrical charge of the battery
The handset is blinking, when the LED is on and off for an equal amount of time. The handset is
winking, when the LED is on for a short period of time and off for a longer period of time.
Led Color
Blue (on
headset)
LED State
Indicates
Solid
Headset microphone is muted.
Blinking
Headset is in pairing mode.
Winking
Active audio path between Headset and
Module.
Solid for 2 seconds
Indicates one of the following:
• Pairing successful
• New battery installed
Green (on
cradle)
Solid
Battery is fully charged.
Blinking
Battery is charging.
Winking
Indicates low voltage when headset is
uncradled.
Off
When headset is cradled, indicates battery is
not charging.
Using the Cordless Devices Application
The Cordless Devices Application provides access to module information and pairing for
handset or headsets.
To access the Cordless Devices Application, do one of the following:
• Press
(Applications), and then press Cordless Devices.
• Press a feature button (key) you have programmed as the Cordless Devices Application
key.
For information about programming feature keys, see page 27.
NOTE
When the pairing button on the Cordless Module is pressed, or when the battery
level of a cordless accessory is critically low, the IP phone will automatically open
the Cordless Devices Application.
Viewing Cordless Module Information
You can use the Cordless Module Application to view protocol, firmware, and hardware
information about the module.
To view cordless module information:
Page 76
1.
Press
(Applications), and then press Cordless Devices.
2.
Press Cordless Module Info. Device information appears on the screen.
3.
Press Close to exit.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Troubleshooting
Troubleshooting
The following sections can help you solve problems that you may be experiencing with your IP
phone. Troubleshooting topics include:
• Contact Information: Information about system administrator contacts.
• Error Messages: Error messages and descriptions.
• Troubleshooting Tips: Possible problems and methods to solve them.
Contact Information
Your system administrator can help you with items such as changing your settings or modifying
phone features. System administrator duties include:
• Adding new user accounts.
• Setting the date and time.
• Programming System Speed-Dial numbers.
• Making database changes, such as changing user names and extension numbers.
Contact your system administrator with questions that are not covered in this user guide. If you
need further assistance, you can find provider information on the Mitel Web site
(www.mitel.com). All sales, service, and support are coordinated at the local level.
Error Messages
The following error messages may appear when using your IP phone.
Message
Reason
CANNOT ACCESS FEATURE
The feature is enabled but other feature-related
conditions were not met. Make sure that all featurerelated conditions are met and retry.
CANNOT ACCESS RESERVED
FEATURE
Your system does not support the feature. Contact your
system administrator for more information.
INVALID FEATURE CODE
The feature code entered does not exist. Retry using
the correct feature code (see page 24).
INVALID EXTENSION NUMBER
The extension number entered does not exist. Retry
using a valid extension number.
NO UPDATE PERFORMED
The feature was not completed or one or more feature
conditions were not met.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 77
Troubleshooting
Troubleshooting Tips
The following table includes troubleshooting tips for phone and system features.
NOTE
You can often correct problems that you may be experiencing by resetting the IP
phone to the default settings. See “Resetting the IP Phone to the Default Settings”
on page 27.
Problem
Possible Solution
The IP phone is not working properly. Contact your system administrator.
I cannot use one or more of the
features described in this guide.
The feature may not be enabled. Contact your system
administrator for more information.
I cannot program System Speed-Dial
numbers.
Your system administrator programs System Speed
Dial numbers.
I cannot change the time and date on
the phone display.
Your system administrator programs the time and date.
Contact your system administrator if you notice that the
date and time are incorrect.
I am experiencing audio problems on
my phone such as echo, distorted
sound, or choppiness.
Contact your system administrator if you are having
audio problems.
The name on the display is incorrect. Your system administrator assigns display names.
I cannot use the local telephone
company star codes (for example,
*82, *69) when I press the Outgoing
button or use the Outgoing Call
access code (8 is the default code)
when calling an external number.
Rather than pressing the Outgoing button or 8 to
access an outside line, you must dial a Select Line
Group number before you can use the star codes. For
example, if your system is using the default Select Line
Group numbers, dial 92001 to access that line. After
you have dial tone, you can dial the star code and the
number.
I cannot use the Agent Help, Record- If your system uses Peer-to-Peer (P2P) audio, you
a-Call, or Station Monitor feature.
cannot use these features when you are on a P2P call.
Contact your system administrator for more
information.
I cannot program a Station Speed
Dial number to the button I want.
Page 78
Before assigning the speed-dial number to a
programmable button, you must store the number with
either a Station Speed-Dial bin.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Troubleshooting
Problem
Possible Solution
When I try to use the Dynamic
Extension Express – Handoff feature
(388), the display shows NO CALL
TO HANDOFF.
The NO CALL TO HANDOFF display indicates that the
call cannot be handed off because one of the following
may have occurred:
• You tried to use the Handoff feature on a call that
has not been routed by Dynamic Extension
Express.
• You tried to use the Handoff feature on a call that
the system has not yet recognized as a valid call.
• You tried to use the Handoff feature on an
unsupported extension. The Handoff feature is
supported on your main extension only.
• You tried to use the Handoff feature on a
phantom extension. The Handoff feature is not
supported on phantom extensions.
• You entered the handoff feature code at the exact
time the other party on the call disconnected.
• The call was terminated for some reason.
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Page 79
Index
Index
Symbols
Callback (Queuing the Phone), requesting 32
Caller ID Information
displaying 42
5310 IP Conference Unit, using 9
5360 IP Phone Features 2
viewing 42
Calls
answering 29, 74, 75
A
camping-on to phone 32
conference 46
About Your IP Phone 1
conference, placing 46
About Your Phone 1
emergency, placing 31
Account Codes, using 38
external 33
ACD Hunt Group Wrap-Up Timer, stopping 64
external, placing 33
ACD Hunt Groups
forwarding 43
logging in 63
logs, using 49
logging out 64
monitoring 66
Agent Help
muting the microphone 39
accepting or rejecting 66
phone, queuing for 32
requesting 65
picking up (reverse transferring) 41
Agent Help Calls, accepting or rejecting 66
Agent Help, requesting 65
Agent, ACD hunt group 63
Alerting Tones and LEDs 72
Angle
adjusting 15
viewing 15
Angle, adjusting and viewing 15
Angle, viewing, adjusting 15
Audio Problems 78
Automatic Access, using 29
Automatic Call Access, using 29
Automatic Trunk Answer, using 30
placing 31
placing internal (IC) 32
recording 48
redirecting 30
stealing 66
transferring 41
waiting 29
waiting, answering 29
Calls On Hold, placing 40
Calls to External Numbers, transferring 41
Calls to Other Extensions, transferring 41
Calls Using the Analog Button, making and answering 12
Calls Using the Failover Mode, making and answering 13
Camp-On, using 32
Characters, entering dialpad 21
B
Codes
account 38
Background Music 27
default system access 24
Background Music, listening 27
feature, default 24
Backlight, turning on or off 28
Outgoing Call access 31, 33
Barge-In, using 67
Comfort and Safety Tips 7, 9
Button Assignments, viewing 27
Conference and Placing all Parties on Hold, ending 47
Buttons 5
Conference Calls
adding a party to 46
C
dropping out of 46
ending 47
Call Forward
Manual 43
placing 46
transferring 46
System 43
Conference Controller Application, accessing/exiting 9
using 43
Conference Party, adding 46
Call Logging, using 49
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Conference Unit On and Off, turning 9
Page 81
Index
Conference Unit Volume, adjusting 9
Display Name, changing 78
Conference Unit, muting 10
Display, calibrating 20
Conference Unit, presentation mode, placing 10
Diverting Hunt Group Calls 65
Conference, transferring 46
DND Settings, changing 52, 55
Configuration Assistant 51
Do-Not-Disturb (DND), using 59
accessing 51
Door Relay, activating 28
using 51
Dropping Out of a Conference 46
Contact Information 77
Dynamic Extension Express
Cordless Device as a Remote Control, using 72
enabling and disabling 45
Cordless Devices
handoff 45
alerting Tones and LEDs 72
settings, changing 52, 54
application, using 76
using 44
cordless handset 73
cordless headset 75
E
cordless module 69
Cordless Devices Application, using 76
Emergency Calls
Cordless Handset 73
placing 31
features 73
LEDs 74
using the LIM Line, placing 31
Emergency Calls, placing 31
Cordless Handset Features 73
Enabling or Disabling the Page Feature 61
Cordless Handset LEDs 74
Ending a Conference and Placing all Parties on Hold 47
Cordless Headset 75
Entering a Hookflash 40
features 75
LEDs 76
Error
messages 77
Cordless Headset Features 75
tones, phone 7
Cordless Headset LEDs 76
Error Messages 77
Cordless Module 70
Extension Numbers 24
Cordless Module and Devices, pairing 71
External Calls, placing 33
Cordless Module Information, viewing 76
External Numbers, redialing 33
Cordless Modules and Devices, pairing 71
External Speaker 6
D
F
Default
Feature
access codes 24
buttons 5
feature codes 24
canceling 5
programmable buttons, resetting to 27
settings, returning the phone to 27
system access codes 24
Default Access Codes 24
Default Feature Codes 24
Dialpad
buttons 5
characters, entering 21
Dialpad Buttons 5
Dialpad Buttons to Enter Characters, using 21
Directory, using 37
codes, using 24
Feature Buttons 5
Features to Programmable Buttons, assigning 23
Forwarding Calls 43
G
Gadget Sidebar 3
Getting Help 28
Group Listen, using 48
Display 3
Display and Softkeys 3
Display Contrast and Brightness, adjusting 16
Page 82
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Index
H
K
Handset 3
Keymaps
off-hook 7
changing 28
off-hook, on-hook 7
switching 28
on-hook 7
Handset and Headset Combinations 70
L
Handsfree Mode
overriding 39
Language, changing 17
using 39
Line Interface Module (LIM), using 11
Handsfree Mode, using 39
Logging out of ACD Hunt Groups, logging out 64
Hang Up 74, 75
Logs, call 49
Hanging Up 75
Low Battery Level 72
Headset Instructions 8
Headset, using 8
M
Hold
Individual 40
System 40
Hookflash, entering 40
Hunt Group Calls
diverting 65
Manual Call Forwarding 43
Manual Call Forwarding Settings, changing 53, 55
Members, hunt group 63
Messages
canceling 58
stealing 66
deleting 58
Hunt Group Calls, stealing 66
Do-Not-Disturb 59
Hunt Group Supervisor Features 66
error 77
Hunt Groups
leaving 57
accepting or rejecting Agent Help 66
pages 61
Agent Help, requesting 65
reminder 60
agent IDs 63
replying to 58
Automatic Call Distribution (ACD) 63
viewing 58
Barge-In, using 67
viewing and responding 58
calls
voice, listening to 58
diverting 65
monitoring 66
stealing 66
Messages at Other Extensions, leaving 57
Messages Left at Other Extensions, canceling 58
logging out of 64
Messages, viewing and responding 58
types 63
Microphone, muting 39
Uniform Call Distribution (UCD) 63
Music, background 27
wrap-up timer 64
Mute, using 39
I
N
Individual Hold, using 40
Navigation Page Buttons 6, 7
Internal Calls, placing 32
Number, redialing 33
Inter-Station Messages, deleting 58
Numbers
IP Phone to the Default Settings, resetting 27
redialing 33
IP Phone, cleaning 8
redialing external 33
Page 83
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Index
O
R
Off-Hook 7
Record-A-Call, using 48
On-Hook 7
Reminder Messages, using 60
Other Hunt Group Features 65
Remote Programming 54
Outgoing Call Access Code 31, 33
change DND settings, using 52, 55
Outside Line Access Codes 24
change the password, using 56
forward calls, using 52, 53, 55
P
Page Announcement, placing 61
Paging
enabling or disabling 61
other system users 61
using 61
Paging Feature, enabling or disabling 61
password
changing 56
entering 51
Remote Programming, using 54
Reverse Transfer (Call Pickup), using 41
Ring Intercom Always, using 39
Ring Message Indicator 4
Ring Tone
changing 16
Password, Remote Programming
changing 56
entering 51
Phone
5360 IP Phone 2
angle, viewing, changing 15
selecting 16
Ring Tone, changing 16
Ring/Message Indicator 4
S
blank display 1
changing volume levels 16
Screen Saver, using 19
comfort and safety 7
Secondary Extension Buttons, using 50
default settings, returning to 27
Settings, returning to default 27
error tones 7
Speaker 6
feature descriptions 3
Speaker, external 6
features
dialpad buttons 5
feature buttons 5
Navigation Page Buttons 6, 7
Ring/Message Indicator 4
speaker 6
Speakerphone
description 6
Group Listen, using 48
handsfree calls 39
Speed Dial
ring tone, selecting 16
entries to programmable buttons, assigning 36
signals 7
entries, deleting 35
Phone Feature Descriptions 3
Phone Information, viewing 8
Phone Signals 7
Phone to the Default Settings, resetting 27
Programmable Buttons 6
resetting 27
resetting to default values 27
using 23
viewing button assignments 27
station, using 34
system, using 34
using 34
Speed-Dial Numbers to Programmable Buttons
assigning 36
STAR Codes, telephone company 78
Station Messages
canceling 58
deleting 58
leaving 57
replying to 58
viewing 58
Station Monitor, using 66
Station Password, changing 51, 56
Page 84
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Index
Station Speed Dial
numbers
deleting 35
dialing 35
storing 34
using 34
Station Speed-Dial Numbers
deleting 35
dialing 35
storing 34
Status Bar 3
System
forwarding 43
Hold 40
information 9
information, displaying 42
time and date, setting 78
System Forwarding 43
System Information, viewing 42
System Speed Dial, using 34
T
Text Size on the Display, changing 18
Time and Date, system 78
Tips
comfort and safety 7
troubleshooting 78
Tones and LEDs, alerting 72
Transferring Calls 41
transferring 41
V
Voice Mail User Guides 57
Voice Messages
deleting 58
leaving 57
listening to 58
Volume Levels 16
Volume Levels, changing 16
W
Welcome 1
Wrap-Up Timer, stopping 64
Page 85
Mitel® 5360 IP Phone User Guide – Issue 1, June 2010
Part No. 550.8124
Issue 1, June 2010
A661/9235A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement