Craftsman | 315.114510 | Operator`s manual | Craftsman 315.114510 Operator`s manual

Operator's Manual
I:RRFTSMRN'I
3/8 in. CORDLESS DRILL-DRIVER
Reversible
Model Nos.
315.114500
7.2 Volt / Two Speed
315.114510
9.6 Volt / Variable Speed
315.114500 - 7.2 VOLT
Save this manual for
future reference
315.114510 - 9.6 VOLT
,_ WARNING:
To reduce the risk of
injury, the user must read and
understand the operator's manual before
using this product.
Customer
Help Line: 1-800-932-3188
Sears, Roebuck
and Co., 3333 Beverly
Rd., Hoffman
Visit the Craftsman web page: www.sears.com/craftsman
983000-181
2-03
Estates,
IL 60179
USA
0( us
•
Table Of Contents ..........................................................................................................................................................
2
•
Warranty .........................................................................................................................................................................
2
•
Introduction .....................................................................................................................................................................
3
•
General Safety Rules, Specific Safety Rules, and Symbols ......................................................................................
•
Product Specifications ....................................................................................................................................................
•
Features .....................................................................................................................................................................
•
Operation ................................................................................................................................................................
•
Maintenance .................................................................................................................................................................
15
•
Accessories ..................................................................................................................................................................
15
•
Exploded View and Repair Parts List .....................................................................................................................
•
Parts Ordering / Service ...............................................................................................................................................
FULL ONE YEAR WARRANTY ON CRAFTSMAN
3-6
7
7-9
10~14
16-17
18
3/8 in. CORDLESS DRILL-DRIVER
If this CRRFTSMIIN 3/8 in. Cordless Drill-Driver fails to give complete satisfaction within one year from the date of purchase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES,
and Sears will replace it, free of charge.
If this I:RRFTSMflH 3/8 in. Cordless Drill-Driver is used for commercial or rental purposes, this warranty applies for only
90 days from the date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
,_L
,_.
Look for thisYour
symbol
to point
out important safety precautions,
attention!H
safety
is involved.
It means
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears
Retail Stores. Always wear eye protection which is marked to comply with ANSI Z87.1.
SAFETY
AND INTERNATIONAL
SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance, and repair information.
MEANING
Do not expose to rain or use in damp locations.
Yourdrill-driverhasmanyfeaturesformakingyourdrilling
operations
morepleasantandenjoyable.
Safety,
performance
anddependability
havebeengiventop
priorityinthedesignofthisdrill-drivermakingiteasyto
maintainandoperate.
,_
_i,
Personal
WARNING:
Read and understand all instructions.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
SAVE THESE
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious
personal injury.
•
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
•
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or inserting
the battery pack into a tool with the switch on, invites
accidents.
•
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
•
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations. Do not use
on a ladder or unstable support.
•
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Work Area
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
•
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
•
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
Electrical
•
•
Safety
Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery. Use battery
only with charger listed.
MODEL
315.114500
MODEL
ASSEMBLY
315.114510
•
BATTERY PACK
Item No. _911051
(1323423)
BATTERY PACK
Item No.-911054
(1323424)
CHARGER
Item No. _911050
(981496-001 )
CHARGING
Item No.-9 11053
(1425003)
Use battery operated tool only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire. Use only with battery pack
listed.
3
Safety
•
INSTRUCTIONS
•
WARNING: Do not attempt to use this product until
you read thoroughly and understand completely the
operator's manual. Pay close attention to the safety
rules including Dangers, Warnings and Cautions. If
you use this product properly and only as intended,
you will enjoy years of safe, reliable service.
Tool Use and Care
•
•
•
•
•
•
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off. A
tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect battery pack from tool or place the switch in
the locked or off position before maldng any adjustments, changing accessories, or stodng the tool. Such
preventive safety measures reduce riskof starting the tool
accidentally.
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
•
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools, with sharp
cutting edges are less likely to bind and are easier to
control.
•
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool, may create a risk of injury when
used on another tool.
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
•
•
Service
•
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden
wiring. Contact with a "live"wire will make exposed metal parts of the tool "live" and shock the operator.
Additional
•
•
Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gage size (A.W.G.) of at least 16 is
recommended for an extension cord 100 feet or less
in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting
in boss of power and overheating.
Important
•
Rules For Safe Operation
Rules for Battery
Tools
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
•
•
•
•
Do not place battery tools or their batteries near
fire or heat. This will reduce the risk of explosion and
possible injury.
Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light.
To reduce the risk of serious personal injury, never use
any cordless product in the presence of open flame. An
exploded battery can propel debris and chemicals. If
exposed, flush with water immediately.
Do not charge battery tool in a damp or wet location. Following this rule will reduce the risk of electric
shock.
For best results, your battery tool should be
charged in a location where the temperature is
more than 50°F but less than 1O0°F. Do not store
outside or in vehicles.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice or
vinegar. It liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
•
Never use a battery that has been dropped or received
a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped battery immediately. Failure to heed this warning can result in serious
personal injury.
•
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, and product using battery charger. Following this rule will reduce the risk of electric shock, fire,
or serious personal injury.
•
•
To reduce risk of injury, charge only nickel-cadmium and nickel metal hydride type rechargeable
batteries. Other types of batteries may burst
causing personal injury and damage. Following this
rule will reduce the risk of electric shock, fire, or
serious personal injury.
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of
electric shock or fire. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
•
To reduce the risk of electric shock, unplug
charger from outlet before attempting any maintenance or cleaning. Turning off controls will not
reduce this risk. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
•
Use of an attachment not recommended or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
•
Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
RISK OF ELECTRIC SHOCK. DO NOT TOUCH
UNINSULATED PORTION OF OUTPUT CONNECTOR OR UNINSULATED BATTERY TERMINAL.
•
•
To reduce risk of damage to charger body and
cord, pull by charger plug rather than cord when
disconnecting
charger. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them
these instructions also. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress. Following this rule will reduce
the risk of serious personal injury.
•
_kWARNING:
Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemicallytreated lumber.
An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet) 25'
50'
100'
Cord Size (AWe)
16
16
Note: Awe
16
= American Wire Gage
Do not operate charger with a damaged cord or
plug. If damaged, have replaced immediately by a
qualified serviceman. Followingthis rule will reduce the
risk of electric shock, fire, or serious personal injury.
5
Important:Someof the
interpretation
following symbols may be used on your tool. Please study them and learn their meaning. Proper
of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
min
Minutes
Time
Alternating Current
Type or a characteristic
of current
Direct Current
Type or a characteristic
of current
No Load Speed
Rotational speed, at no load
V
no
.../rain
Revolutions or Reciprocation
Per Minute
Indicates danger, warning or caution.
It means attention!!! Your safety is
involved.
Safety Alert Symbol
Wear Eye Protection
Q
Revolutions, strokes,
surface speed, orbits etc. per minute
glasses with side shields and a full face
Always wear safety goggles or safety
shield when operating this product.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention
measures.
Symbol
Meaning
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
A
NOTE:
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices that may cause property damage.
Advises you of information or instructions vital to the operation or maintenance of the equipment.
SAVE THESE INSTRUCTIONS
6
DRILL-DRIVER
315.114500
315.114510
Chuck
Motor
Switch
No Load Speed
Clutch
3/8 in. Keyless
DC Motor 7.2 Volt
3/8 in. Keyless
DC Motor 9.6 Volt
Two Speed
250 / 550 RPM
24 Positions
70 in.lb.
Item No. =11050
Variable Speed
0-600 RPM
24 Positions
(981496-001)
120 V, 60 Hz, AC only
7.2 Volt
3-6 Hours
(1425003)
120 V, 60 Hz, AC only
9.6 Volt
Maximum Torque
CHARGER
Rating
Charging Voltage
Charge Rate
BATTERY PACK
"Craftsman
90 in.lb.
Item No. 311053
Item No. _11051
3-6 Hours
Item No. 311054
(1323423)
(1323424)
EX 114500 - 7.2V test criteria
70
70
190
in.lb, torque
3/8 in. diameter holes per battery pack charge into 2 in. nominal pine lumber.
#8 x 1.25 in. wood screws in low speed per battery pack charge into pine lumber.
Craftsman EX 114510 - 9.6V test criteria
90
100
200
KNOW
in.lb, torque
3/8 in. diameter holes per battery pack charge into 2 in. nominal pine lumber.
#8 x 1.25 in. wood screws in low speed per battery pack charge into pine lumber.
YOUR
DRILL-DRIVER
See Figures 1 (a) and 1 (b).
Before attempting to use your drill-driver, familiarize
yourself with all operating features and safety
requirements.
KEYLESS
CHUCK
FORWARD/REVERSE
SELECTOR
(DIRECTION OF ROTATION SELECTOR)
Your drill-driver has a forward/reverse selector located
above the switch trigger.
WRIST
STRAP
SWITCH
See Figure 1 (b).
A wrist strap is provided to reduce the chances of dropping
your drill-driver. Place one hand through the wrist strap
when carrying tool.
To turn your drill-driver ON, depress the switch trigger.
BIT STORAGE
Release switch trigger to turn your drill-driver OFF.
When not in use, bit(s) provided with your drill-driver can
be placed in the storage area located on the bottom of the
motor housing.
Your drill-driver has a keyless chuck that allows you to hand
tighten or release drillbit in the chuck jaws.
SWITCH
LOCK
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use.
TWO SPEED (MODEL 315.114500)
Drill model 315.114500 has a two-speed feature in the
switch. For low speed, depress switch trigger halfway. For
high speed, depress switch trigger all the way.
VARIABLE
SPEED (MODEL 315.114510)
Drill model 315.114510 has a variable speed switch that
delivers higher speed with increased trigger pressure.
Speed is controlled by the amount of switch trigger
depression.
LEVEL
To keep drill bit level during drilling operations, a level is
located on the back of the motor housing.
,_k
WARNING: If any parts are missing, do not operate
your drill-driver until the missing parts are replaced.
Failure to do so could result in possible serious
personal injury.
LEVEL
MODEL 315.114500
CHARGER
TORQUE
7,2 VOLT
KEYLESS
CHUCK
SWITCH
TRIGGER
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
SCREWDRIVER
BIT
BIT
STORAGE
BATTERYPACK
SHOWNINTOOL
CHARGER
PLUG
INPUTJACK
KEYLESS
CHUCK
TORQUE
ADJUSTMENT
RING
WRIST
STRAP
Fig. 1 (a)
MODEL 315.114510
9.6 VOLT
LEVEL
BATTERY PACKSHOWN
IN CHARGINGSTAND
CHARGER
SWITCH
TRIGGER
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
\
BIT
STORAGE
SCREWDRIVER
BITS
RED LIGHT
(LED)
BATTERY
PACK
WRIST
STRAP
CHARGING
STAND
8
Fig. 1 (b)
_k
CHARGING
BATTERY
MODEL 315.114510
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
PACK FOR
See Figure 1 (b).
•
Charge battery pack only with the charging assembly
provided.
•
Make sure power supply is normal household
voltage, 120 volts, 60 Hz, AC only.
•
Connect charger to power supply.
•
The battery pack for your tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it overnight prior to use.
Place battery pack in charging stand. Align raised rib
on battery pack with groove in charging stand.
See Figure 1 (b).
•
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by
recharging) for them to become fully charged.
Press down on battery pack to be sure contacts on
battery pack engage properly with contacts in charging
stand.
•
The charge indicator light (LED), located on the
charging stand, will light up red and glow when the
charger is properly connected to power supply. This
light indicates the charger is operating properly. It will
remain on until battery pack is removed from charging
stand or charger is disconnected from power supply.
_,
u
WARNING:
Do not allow familiarity with your drilldriver to make you careless. Remember that a
careless fraction of a second is sufficient to inflict
severe injury.
BA'n'ERY
PACK
CHARGING
BATTERY
MODEL 315.114500
PACK FOR
See Figure 1 (a).
•
•
Charge battery pack only with the charger provided.
Make sure power supply is normal household
voltage, 120 volts, 60 Hz, AC only.
•
•
Connect charger to battery pack by inserting charger
plug into input jack. As shown in Figure 1 (a), input
jack is located on the back side of battery pack.
Note: If charger does not charge battery pack, return
battery pack and charging assembly to your nearest
Sears Repair Center for electrical check.
•
After normal usage, 3 hours or less of charging time is
required to fully recharge battery pack. Note: If battery
pack is completely discharged, 6 hours or longer of
charging time is required to fully recharge battery
pack.
•
The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
•
Do not place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
•
When batteries become fully charged, unplug charger
from power supply and remove the battery pack.
Note: The battery pack can remain in the drill while
charging or you can remove it from drill to charge.
When battery pack is out of the drill, be careful not to
touch both terminals with a metal object. Touching
both terminals with a metal object will short out the
battery pack.
•
Connect charger to power supply.
•
The charge indicator light (LED), located on the battery
pack, will light up red and glow when the charger is
properly connected to battery pack and power supply.
This light indicates the charger is operating properly. It
will remain on until charger is disconnected from
power supply. The light only glows while your tool is
charging, not during use.
•
The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
•
Do not place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
Do not operate the tool while it is connected to the
charger. The drilling ability will not increase.
•
When using your
your battery pack
battery pack cool
before attempting
After normal usage, 3 hours or less of charging time is
required to fully recharge battery pack. Note: If battery
pack is completely discharged, 6 hours or longer of
charging time is required to fully recharge battery
pack.
•
•
IMPORTANT
INFORMATION
HOT BATTERIES
FOR RECHARGING
drill-driver continuously, the batteries in
will become hot. You should let a hot
down for approximately 30 minutes
to recharge.
Note: This situation only occurs when continuous use of
your drill causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "CHARGING
BATTERY PACK" for normal recharging of batteries. If
the charger does not charge your battery pack under
normal circumstances, return both the battery pack and
charger to your nearest Sears repair center for electrical
check.
When battery pack become fully charged, unplug
charger from power supply and disconnect it from
battery pack.
9
SWITCH
TO INSTALL BAI-rERY
See Figure 2.
•
To turn your drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
Lock switch trigger on your drill by placing the direction
of rotation selector in center position. See Figure 4.
•
Place battery pack in your drill. Align raised rib on
battery pack with groove inside drill. See Figure 3.
SWITCH
TRIGGER
TWO SPEED
(MODEL
PACK
BATTERY
PACK
Fig. 2
315.114500)
LATCHES
Drill model 315.114500 has a two speed feature in the
switch. Depress the switch trigger halfway for driving
screws at low speed. Depress the switch trigger all the
way for normal drilling. Release the switch trigger to turn
drill off.
VARIABLE
SPEED
(MODEL
315.114510)
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed is
controlled by the amount of switch trigger depression.
_DEPRESSLATCHESTO
RELEASEBATTERYPACK
Note: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned, this is a normal
part of the switch function.
•
,_
Make sure the latches on each side of your battery
pack snap in place and battery peck is secured in drill
before beginning operation.
CAUTION:
When placing battery pack in your drill,
be sure raised rib on battery pack aligns with groove
inside drill and latches snap into place properly.
Improper assembly of battery pack can cause
damage to internal components.
TO REMOVE
10
Fig. 3
BATTERY
PACK
•
Lock switch trigger on your drill by placing the direction
of rotation selector in center position. See Figure 4.
•
Locate latches on end of battery pack and depress to
release battery pack from your drill. See Figure 3.
•
Remove battery pack from your ddll.
SWITCH LOCK
KEYLESS CHUCK
See Figure 4.
See Figure 5.
The switch trigger can be locked in the OFF position. This
feature can be used to prevent the possibility of accidental
starting when not in use. To lock switch trigger, push the
direction of rotation selector (Forward/Reverse Selector)
to the center position.
Your drill has a keyless chuck. As the name implies, you can
hand tighten or release drill bits in the chuck jaws. Grasp and
hold the collar of the chuck with one hand. Rotate the chuck
body with your other hand. The arrows on the chuck
indicate which direction to rotate the chuck body in order to
LOCK (tighten) or UNLOCK (release) the ddll bit.
SELECTORWITH
CENTERLOCKPOSITION
REVERSE
CHUCK
JAWS
UNLOCK
(RELEASE)
CHUCK
COLLAR
DRILLBIT
FORWARD
SWITCH
TRIGGER
LOCK
(TIGHTEN)
Fig. 4
_i
WARNING:
Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
_
REVERSIBLE
See Figure 4.
This tool has the feature of being reversible. The direction
of rotation is controlled by a selector located above the
switch trigger. With the drill held in normal operating
position, the direction of rotation selector should be
positioned to the left of the switch for drilling. The drilling
direction is reversed when the selector is to the right of
the switch. When the selector is in center position, the
switch trigger is locked.
_i
CAUTION: To prevent gear damage, always allow
chuck to come to a complete stop before changing
the direction of rotation.
To stop, release switch trigger and allow the chuck to come
to a complete stop.
11
CHUCK
BODY
WARNING:
Do not hold chuck body with one hand
and use power of the drill to tighten chuck jaws on
drill bit. Chuck body could slip in your hand or your
hand could slip and come in contact with rotating drill
bit. This could cause an accident resulting in serious
personal injury.
INSTALLINGBITS
REMOVING BITS
See Figure 6.
See Figure 6.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 4.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 4.
•
Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
Also, raise the front of your drill slightly to keep the bit
from falling out of the chuck jaws.
•
Loosen the chuck jaws from drill bit.
•
To loosen: grasp and hold the collar of the chuck with
one hand, while rotating chuck body with your other
hand. Note: Rotate chuck body in the direction of the
arrow marked UNLOCK to loosen chuck jaws.
•
Do not use a wrench to tighten or loosen the chuck
jaws.
•
Remove drill bit from chuck jaws.
•
Insert drill bit straight into chuck the full length of the
jaws as shown in Figure 6.
•
Tighten the chuck jaws on drill bit.
CHUCK
JAWS
UNLOCK
(RELEASE)
CHUCK
COLLAR
ADJUSTABLE
TORQUE
CLUTCH
Your drill is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
The proper setting depends on the type of material and the
size of screw you are using.
TO ADJUST
TORQUE
Identity the twenty four torque indicator settings located
on the front of your drill. See Figure 8.
Rotate adjusting ring to the desired setting.
DRILLBIT
LOCK
(TIGHTEN)
CHUCK
BODY
RIGHT
•
•
,_
Fig. 6
To tighten the chuck jaws on drill bit; grasp and hold
the collar of the chuck with one hand, while rotating
the chuck body with your other hand.
1-4
For driving small screws.
5 -8
For driving screws into soft
material.
9 - 12
• 13 - 16
For driving screws into soft and hard
materials.
For driving screws in hard wood.
• 17 - 20
For driving large screws.
• 24 - <1,11 For heavy drilling.
Note: Rotate the chuck body in the direction of the
arrow marked LOCK to tighten chuck jaws.
Do not use a wrench to tighten or loosen the chuck
jaws.
TO DECREASE
TORQUE
ADJUSTING
RING
WARNING:
Make sure to insert drill bit straight into
chuck jaws. Do not insert drill bit into chuck jaws at
an angle then tighten, as shown in Figure 7. This
could cause drill bit to be thrown from drill, resulting
in possible serious personal injury or damage to the
chuck.
TOINCREASE
TORQUE
Fig. 7
12
Fig. 8
BIT STORAGE
DRILLING
See Figure 9.
See Figure 11.
When not in use, bit(s) provided with your drill can be
placed in the storage area located on the bottom of your
drill. As shown in Figure 9, model 315.114500 has one bit
storage slot and model 315.114510 has two bit storage
slots.
SCREWDRIVER
315.114500
315.114510
_J_
SCREWDRIVER
BIT
BIT
STORAGEAREA
,_
Fig. 11
Fig. 9
When drilling hard smooth surfaces use a center punch to
mark desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However,
the low speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate
your drill at a low speed until the hole is started.
WARNING: Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
LEVEL
The material to be drilled should be secured in a vise or
with clamps to keep it from turning as the drill bit rotates.
See Figure 10.
A convenient feature provided with your drill is a level. It
is recessed in the motor housing on back of your drill. It
can be used to keep drill bit level during drilling operations.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
REARVIEW OF DRILL
_k
WARNING:
Be prepared for binding or bit
breakthrough. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material. If not prepared, this loss
of control can result in possible serious injury.
When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit
and increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
LEVEL
Fig. 10
13
•
CHUCKREMOVAL
Insert hex key in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise
direction. This will loosen chuck on the spindle. It can
now be unscrewed by hand. See Figure 14.
See Figures 12, 13, and 14.
The chuck must be removed in order to use some
accessories. To remove:
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 4.
•
Insert a 5/16 in. or larger hex key into the chuck of your
drill and tighten the chuck jaws securely.
•
Tap the hex key sharply with a mallet in a clockwise
direction. See Figure 12. This will loosen the screw in
the chuck for easy removal.
MALLET
CHUCK
JAWS
Fig. 14
TO RETIGHTEN
•
CHUCK
The chuck may become loose on spindle and develop a
wobble. Periodically check chuck screw for tightness.
KEYLESS
CHUCK
HEXKEY
A LOOSE
Fig. 12
Open chuck jaws and remove hex key. Remove the
chuck screw by turning it in a clockwise direction. See
Figure 13.
Note: The screw has left hand threads.
To tighten, follow these steps:
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 4.
•
Open the chuck jaws.
•
Insert hex key into chuck and tighten chuck jaws
securely. Tap hex key sharply with a mallet in a
clockwise direction. This will tighten chuck on the
spindle.
•
Open the chuck jaws and remove hex key.
•
Tighten the chuck screw.
Note: The chuck screw has left hand threads.
SCREWDRIVER
Fig. 13
14
_L
Do not abuse power tools. Abusive practices can
damage tool as well as workpiece.
WARNING:
When servicing, use only identical
Craftsman replacement parts. Use of any other
part may create a hazard or cause product damage.
Only the parts shown on parts list, pages16 and !7, are
intended to be repaired or replaced by the customer. All
other parts should be replaced at a Sears Service Center.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
_i
_1,
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken or destroy
plastic.
WARNING:
Do not attempt to modify this tool or
create accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
BA'FrERIES
Your drill's battery pack is equipped with nickel-cadmium
rechargeable batteries. Length of service from each
charging will depend on the type of work you are doing.
•
Store and charge your batteries in a cool area.
Temperatures above or below normal room
temperature will shorten battery life.
The batteries in this tool have been designed to provide
maximum trouble free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry,
could result in a serious burn.
•
Never store batteries in a discharged condition.
Recharge them immediately after they are
discharged.
•
All batteries gradually lose their charge. The higher
the temperature the quicker they lose their charge. If
you store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life.
To obtain the longest possible battery life, we suggest the
following:
To preserve natural resources, please
recycle or dispose of batteries properly.
BATTERY PACK REMOVAL AND PREPARATION
FOR RECYCLING
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of nickel-cadmium
batteries in ordinary trash.
_i
Consult your local waste authority for information
regarding available recycling and/or disposal options.
The following recommended
accessories
WARNING:
Upon removal, cover the battery pack's
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
are currently available at Sears Retail Stores.
•
6-Pc. Extra Length Magnite Power Bit Set
•
17-Pc. Power Screwdriver/Nutdriver
•
30-Pc. Power Screwdriver/Nutdriver
•
High Speed Bits (For Wood or Metal)..3/4 in. Max.
_k
WARNING:
Set and Case
The use of attachments or accessories
not listed might be hazardous.
15
Set and Case
CRAFTSMAN
3/8 in. CORDLESS
MODEL
I
DRILL-DRIVER
NO, 315.114500
The
in allmodel
correspondence
numberwill regarding
be found on
your
a plate
3/8 in,
attached
CORDLESS
to the motor
DRILL-DRIVER
housing. Always
or when
mention
ordering
the model
repair number
parts.
SEE BACK
PAGE
FOR PARTS
ORDERING
INSTRUCTIONS
MODEL 315.114500
2
PARTS LIST
Key
No.
Part
Number
Description
1
616478-003
Screw (Special) .................................................................
1
2
6903326
Chuck (Item No. _ 20988) .................................................
1
Quan.
3
* Item No. 9 11051
Battery Pack (1323423) ....................................................
1
4
* Item No. 9 11050
Charger (981496-001)
1
5
......................................................
3064304
Carrying Case - Not Shown .............................................
983000-181
Operator's
Manual
* Can Be Purchased Thru RSOS (Retail Special Order System)
16
1
I
CRAFTSMAN
I
3/8 in. CORDLESS
DRILL-DRIVER
MODEL NO. 315.114510
The model number will be found on a plate attached to the motor housing. Always mention the model number
in all correspondence regarding your 3/8 in. CORDLESS DRILL-DRIVER or when ordering repair parts.
SEE BACK
PAGE FOR PARTS
ORDERING
I
I
INSTRUCTIONS
MODEL 315.114510
2
4
PARTS LIST
Key
No.
Part
Number
Description
1
616478-003
Screw (Special) .................................................................
1
2
6903326
Chuck (Item No. _ 20988) .................................................
1
Quan.
3
* Item No. 9 11054
Battery Pack (1323424) ....................................................
1
4
* Item No. 9 11053
Charging Assembly (1425003) .........................................
1
3064304
Carrying Case - Not Shown .............................................
1
983000-181
Operator's Manual
5
* Can Be Purchased Thru RSOS (Retail Special Order System)
•
i
17
Get it fixed,lat VoUEl omeer ours!
Your Home
For repair-in
your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold itt
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
Call anyttme,
®
(1-800-4694663)
day or night(U.S.A
www.sears.com
and Canada)
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime,
day or night (U S.A only)
www.sears.com
To purchase a protection agreement (U.S.A,)
or maintenance agreement (Canada) on a product serviced
1-800-827-6655
(u S.A)
Para ped_r serv_c_o de reparaci6n
a dom_cilio, y para ordenar p_ezas
1-888-SU-HOGAR
sM
1-800-361-6665
Au Canada
by Sears:
(Canada)
pour service en fran£:a_s.
1-800-LE-FOYER
Mc
(1-800-533-6937)
(1-888-784-6427)
Trademark I TM Trademark / SM Service Mark of Sears, Roebuck and Co
TM
S&_
® Marca Registrada I
Marca de F_br_c_ !
Marca de ServK:lo de Sears, Roebuck and Co
uc Marque de commerce ! MD Marque deposee de Sears, Roebuck and Co
www sears ca
® Registered
© Sears,
Roebuck
and C'o
Download PDF