Operating Instructions PT-DW740E PT-DW740EL

Operating Instructions
Functional Manual
DLPTM Projector   Commercial Use
PT-DW740E
PT-DW740EL
PT-DX810E
PT-DX810EL
Model No.
Thank you for purchasing this Panasonic product.
■■ This manual is common to all the models regardless of suffixes of the Model No.
zzS: Silver model, the standard zoom lens supplied
K: Black model, the standard zoom lens supplied
LS: Silver model, the lens sold separately
LK: Black model, the lens sold separately
■■ Before operating this product, please read the instructions carefully and save this manual
for future use.
■■ Before using your projector, be sure to read “Read this first!” (x pages 2 to 8).
ENGLISH
TQBJ0446
Read this first!
Read this first!
WARNING: THIS APPARATUS MUST BE EARTHED.
WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain
or moisture.
Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator
position is equal or less than 70 dB (A) according to ISO 7779.
WARNING:
1. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time.
2.To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified
service personnel.
3.Do not remove the earthing pin on the mains plug. This apparatus is equipped with a three prong
earthingtype mains plug. This plug will only fit an earthing-type mains socket. This is a safety feature. If you
are unable to insert the plug into the mains socket, contact an electrician. Do not defeat the purpose of the
earthing plug.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
CAUTION:
To assure continued compliance, follow the attached installation instructions, which include
using the provided power cord and shielded interface cables when connecting to computer or
peripheral device. If you use serial port to connect PC for external control of projector, you must
use a commercial RS-232C serial interface cable with ferrite core. Any unauthorized changes or
modifications to this equipment will void the user’s authority to operate.
Product information (for Turkey only)
EEE Yönetmeliğine Uygundur.
EEE Complies with Directive of Turkey.
2 - ENGLISH
Be sure to read “Read this first!”
Read this first!
IMPORTANT: THE MOULDED PLUG (U.K. only)
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse
is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating
of 13 amps and that it is approved by ASTA or BSI to BS1362.
or the BSI mark
on the body of the fuse.
Check for the ASTA mark
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you
lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover
can be purchased from an Authorised Service Center.
If the fitted moulded plug is unsuitable for the mains socket in your home, then the fuse should be
removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the
cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING:
THIS APPLIANCE MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green - and - Yellow:
Earth
Blue:
Neutral
Brown:
Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows.
The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the
plug which is marked with the letter E or by the Earth symbol
or coloured GREEN or GREEN AND - YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked
with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is marked
with the letter L or coloured RED.
ASA
L
HE
-8
13
A2
50
V
N
BS
13
63
/A
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
ENGLISH - 3
Read this first!
WARNING:
„„ POWER
The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible
when problems occur. If the following problems occur, cut off the power supply immediately.
Continued use of the projector in these conditions will result in fire or electric shock.
zz If foreign objects or water get inside the projector, cut off the power supply.
zz If the projector is dropped or the cabinet is broken, cut off the power supply.
zz If you notice smoke, strange smells or noise coming from the projector, cut off the power supply.
Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.
During a thunderstorm, do not touch the projector or the cable.
Electric shocks can result.
Do not do anything that might damage the power cord or the power plug.
If the power cord is used while damaged, electric shocks, short-circuits or fire will result.
zz Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it
excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.
Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.
Completely insert the power plug into the wall outlet and the power connector into the projector terminal.
If the plug is not inserted correctly, electric shocks or overheating will result.
zz Do not use plugs which are damaged or wall outlets which are coming loose from the wall.
Do not use anything other than the provided power cord.
Failure to observe this will result in fire or electric shocks. Please note that if you do not use the provided power
cord to ground the device on the side of the outlet, this may result in electric shocks.
Clean the power plug regularly to prevent it from becoming covered in dust.
Failure to observe this will cause a fire.
zz If dust builds up on the power plug, the resulting humidity can damage the insulation.
Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.
Do not handle the power plug and power connector with wet hands.
Failure to observe this will result in electric shocks.
Do not overload the wall outlet.
If the power supply is overloaded (ex., by using too many adapters), overheating may occur and fire will result.
„„ ON USE/INSTALLATION
Do not place the projector on soft materials such as carpets or sponge mats.
Doing so will cause the projector to overheat, which can cause burns, fire or damage to the projector.
Do not set up the projector in humid or dusty places or in places where the projector may come into
contact with oily smoke or steam, ex. a bathroom.
Using the projector under such conditions will result in fire, electric shocks or deterioration of components.
Deterioration of components (such as ceiling mount brackets) may cause the projector which is mounted on the
ceiling to fall down.
Do not install this projector in a place which is not strong enough to take the full weight of the projector
or on top of a surface which is sloped or unstable.
Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage
could result.
4 - ENGLISH
Read this first!
WARNING:
Do not cover the air intake/exhaust ports or place anything within 500 mm (20") of them.
Doing so will cause the projector to overheat, which can cause fire or damage to the projector.
zz Do not place the projector in narrow, badly ventilated places.
zz Do not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.
Do not place your hands or other objects close to the air exhaust port.
Doing so will cause burns or damage your hands or other objects.
zz Heated air comes out of the air exhaust port. Do not place your hands or face, or objects which cannot
withstand heat close to this port.
Do not look at or place your skin into the light emitted from the lens while the projector is being used.
Doing so can cause burns or loss of sight.
zz Strong light is emitted from the projector’s lens. Do not look at or place your hands directly into this light.
zz Be especially careful not to let young children look into the lens. In addition, turn off the power and
disconnect the power plug when you are away from the projector.
Never attempt to remodel or disassemble the projector.
High voltages can cause fire or electric shocks.
zz For any inspection, adjustment and repair work, please contact an Authorized Service Center.
Do not project an image with the lens cover attached.
Doing so can cause fire.
Do not allow metal objects, flammable objects, or liquids to enter inside of the projector. Do not allow
the projector to get wet.
Doing so may cause short circuits or overheating, and result in fire, electric shock, or malfunction of the
projector.
zz Do not place containers of liquid or metal objects near the projector.
zz If liquid enters inside of the projector, consult your dealer.
zz Particular attention must be paid to children.
Use the ceiling mount bracket specified by Panasonic.
Using the ceiling mount bracket other than the specified one will result in falling accidents.
zz Attach the supplied safety cable to the ceiling mount bracket to prevent the projector from falling down.
Installation work (such as ceiling mount bracket) should only be carried out by a qualified technician.
If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks.
zz Do not use anything other than an authorized ceiling mount bracket.
zz Be sure to use the provided accessory wire with an eye bolt as an extra safety measure to prevent the
projector from falling down. (Install in a different location to the ceiling mount bracket.)
ENGLISH - 5
Read this first!
WARNING:
„„ ACCESSORIES
Do not use or handle the batteries improperly, and refer to the following.
Failure to observe this will cause burns, batteries to leak, overheat, explode or catch fire.
zz Use AA/R6 batteries.
zz Do not use unspecified batteries.
zz Do not use chargeable batteries.
zz Do not disassemble dry cell batteries.
zz Do not heat the batteries or place them into water or fire.
zz Do not allow the + and – terminals of the batteries to come into contact with metallic objects such as
necklaces or hairpins.
zz Do not store batteries together with metallic objects.
zz Store the batteries in a plastic bag and keep them away from metallic objects.
zz Make sure the polarities (+ and –) are correct when inserting the batteries.
zz Do not use a new battery together with an old battery or mix different types of batteries.
zz Do not use batteries with the outer cover peeling away or removed.
If the battery fluid leaks, do not touch it with bare hands, and take the following measures if necessary.
zz Battery fluid on your skin or clothing could result in skin inflammation or injury.
Rinse with clean water and seek medical advice immediately.
zz Battery fluid coming in contact with your eyes could result in loss of sight.
In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately.
Do not disassemble the lamp unit.
Doing so can cause electric shocks, burns, or injury.
Lamp replacement
The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will
result.
zz The lamp can easily explode if struck against hard objects or dropped.
zz Before replacing the lamp, be sure to turn the power off and to disconnect the power plug from the wall
outlet.
Electric shocks or explosions can result if this is not done.
zz When replacing the lamp, turn the power off and allow it to cool for at least one hour before handling it
otherwise it can cause burns.
Do not use the supplied power cord with devices other than this projector.
zz Using the supplied power cord with devices other than this projector may cause short circuits or
overheating, and result in electric shock or fire.
Remove the depleted batteries from the remote control promptly.
zz Leaving them in the unit may result in fluid leakage, overheating, or explosion of the batteries.
CAUTION:
„„ POWER
When disconnecting the power cord, be sure to hold the power plug and power connector.
If the power cord itself is pulled, the lead will become damaged, and fire, short-circuits or serious electric
shocks will result.
When not using the projector for an extended period of time, disconnect the power plug from the wall
outlet.
Failure to do so may result in fire or electric shock.
Disconnect the power plug from the wall outlet before carrying out any cleaning and replacing the unit.
Failure to do so may result in electric shock.
6 - ENGLISH
Read this first!
CAUTION:
„„ ON USE/INSTALLATION
Do not place heavy objects on top of the projector.
Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or
injury. The projector will be damaged or deformed.
Do not put your weight on this projector.
You could fall or the projector could break, and injury will result.
zz Be especially careful not to let young children stand or sit on the projector.
Do not place the projector in extremely hot locations.
Doing so will cause the outer casing or internal components to deteriorate, or result in fire.
zz Take particular care in locations exposed to direct sunlight or near stoves.
Do not place your hands in the openings beside the optical lens, while shifting the lens.
Failure to observe this could cause injury.
Do not stand in front of the lens while the projector is being used.
Doing so can cause damage and burns to clothing.
zz Strong light is emitted from the projector’s lens.
Do not place objects in front of the lens while the projector is being used.
Doing so can cause damage to the object and can cause the set to malfunction.
zz Strong light is emitted from the projector’s lens.
Always disconnect all cables before moving the projector.
Moving the projector with cables still attached can damage the cables, which will cause fire or electric shocks to
occur.
„„ ACCESSORIES
Do not use the old lamp unit.
If used it could cause lamp explosion.
If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the
broken pieces.
Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and
which contains nearly the same amount of mercury as fluorescent lamps, and the broken pieces will cause
injury.
zz If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical
advice immediately.
zz Ask your dealer about replacing the lamp unit and check the inside of the projector.
Do not attach the air filter unit while it is wet.
Doing so may result in electric shock or malfunctions.
zz After you clean the air filter units, dry them thoroughly before reattaching them.
Do not touch the fan with your fingers or any other parts of your body when changing the lamp unit.
Doing so can cause injury.
Ask your dealer about cleaning inside the projector once a year.
Continuous use while dust is accumulated inside the projector may result in fire.
zz For cleaning fee, ask your dealer.
When not using the projector for an extended period of time, remove the batteries from the remote
control.
Failure to observe this will cause the batteries to leak, overheat, catch fire or explode, which may result in fire
or contamination of surrounding area.
ENGLISH - 7
Read this first!
To remove the battery
Remote Control Battery
1. Press the guide and lift the cover.
(ii)
(i)
8 - ENGLISH
2. Remove the batteries.

rrTrademarks
•Microsoft®, Windows®, Windows Vista®, and Internet Explorer® are the registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries.
•Mac, Mac OS, Mac OSX, and Safari are the trademarks of Apple Inc. registered in the United States and
other countries.
•PJLinkTM is a trademark or pending trademark in Japan, the United States, and other countries and regions.
•HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
•VGA and XGA are trademarks of International Business Machines Corporation.
•SVGA is a registered trademark of the Video Electronics Standards Association.
•RoomView, Crestron RoomView, Crestron Connected, and Fusion RV are trademarks of Crestron Electronics,
Inc.
•The font used in the on-screen displays is a Ricoh bitmap font, which is manufactured and sold by Ricoh
Company, Ltd.
•Adobe Flash Player is either a trademark or registered trademark of Adobe Systems Incorporated in the
United States and/or other countries.
•Other names, company names or product names used in these operating instructions are the trademarks or
registered trademarks of their respective holders.
Please note that the operating instructions do not include the ® and TM symbols.
rrIllustrations in these operating instructions
•Note that illustrations of the projector and screens may differ from the ones you actually see.
rrPage references
•In these instructions, references to pages are indicated as: ( page 00).
rrTerm
•In these instructions, the “Wireless/wired remote control unit” accessories are referred to as the “Remote
control”.
ENGLISH - 9

Features of the Projector
Quick Steps
For details, see the corresponding pages.
High luminance & High color
reproducibility
▶▶The unique optical and lamp drive systems
achieve a high luminance and high color
reproducibility.
Easy setup and improved
serviceability
▶▶Extensive lineup of optional lenses allow
more flexible setup of the projector.
Improved cost performance in
maintenance fee
▶▶The long life filter reduces maintenance
costs.
1. Set up the projector.
(x page 26)
c
2. Attach the projection lens.
(x page 35)
c
3. Connect with other devices.
(x page 37)
c
4. Connect the power cord.
(x page 41)
c
5. Switch on the projector.
(x page 42)
c
6. Make initial settings.*
(x page 19)
c
7. Select the input signal.
(x page 45)
c
8. Adjust the image.
(x page 45)
*These are the steps to be taken when you switch on the power for the
first time after purchasing the projector.
10 - ENGLISH
Contents
Contents
Read this first!.............................................2
Chapter 1 Preparation
Precautions for use.................................................. 14
Cautions when transporting................................... 14
Cautions when installing........................................ 14
Security................................................................. 15
Disposal................................................................. 16
Cautions on use.................................................... 16
Software information regarding this product.......... 16
Accessories........................................................... 17
Optional accessories............................................. 18
Start-up display........................................................ 19
Initial setting (display language)............................ 19
Initial setting (projector setup)............................... 19
About your projector................................................ 20
Remote control...................................................... 20
Projector body....................................................... 21
Using the remote control......................................... 23
Inserting and removing the batteries..................... 23
Setting Remote control ID numbers...................... 23
Connecting to the projector with a cable............... 24
Chapter 2 Getting Started
Setting up.................................................................. 26
Projection method................................................. 26
Parts for ceiling mount (optional)........................... 26
Screen size and throw distance............................ 27
Adjusting adjustable feet....................................... 34
Removing/attaching the projection lens................ 35
Removing the projection lens................................ 35
Attaching the projection lens................................. 35
Connections.............................................................. 37
Before connecting to the projector........................ 37
Connecting example: AV equipment..................... 38
Connecting example: Computers.......................... 38
Chapter 3 Basic Operation
Switching on/off the projector................................. 41
Connecting the power cord................................... 41
Power indicator...................................................... 42
Switching on the projector..................................... 42
Making adjustments and selections...................... 43
Switching off the projector..................................... 43
Direct power off function........................................ 44
Be sure to read “Read this first!”. (x pages 2 to 8)
Projecting.................................................................. 45
Selecting the input signal...................................... 45
Adjusting the focus, zoom, and shift...................... 45
Moving the lens to the home position.................... 46
Adjustment range by the lens position shift
(optical shift)....................................................... 46
Remote control operation........................................ 47
Using the shutter function...................................... 47
Using the on-screen display function.................... 47
Switching the input................................................ 48
Using the status function....................................... 48
Using the automatic setup function....................... 48
Using the function button....................................... 49
Displaying the internal test pattern........................ 49
Changing the picture aspect ratio.......................... 49
Chapter 4 Settings
Menu navigation....................................................... 51
Navigating through the menu................................ 51
Main menu............................................................. 52
Sub-menu.............................................................. 52
[PICTURE] menu....................................................... 55
[PICTURE MODE]................................................. 55
[CONTRAST]......................................................... 55
[BRIGHTNESS]..................................................... 55
[COLOR]................................................................ 56
[TINT].................................................................... 56
[COLOR TEMPERATURE].................................... 56
[WHITE GAIN]....................................................... 57
[SYSTEM DAYLIGHT VIEW]................................. 57
[SHARPNESS]...................................................... 58
[NOISE REDUCTION]........................................... 58
[AI]......................................................................... 58
[SYSTEM SELECTOR]......................................... 59
[POSITION] menu..................................................... 60
[SHIFT].................................................................. 60
[ASPECT].............................................................. 60
[ZOOM].................................................................. 61
[CLOCK PHASE]................................................... 62
[KEYSTONE]......................................................... 63
[ADVANCED MENU] menu....................................... 64
[DIGITAL CINEMA REALITY]................................ 64
[BLANKING].......................................................... 64
[INPUT RESOLUTION]......................................... 65
[CLAMP POSITION].............................................. 65
[EDGE BLENDING]............................................... 65
[RASTER POSITION]............................................ 66
ENGLISH - 11
Contents
[DISPLAY LANGUAGE] menu.................................. 67
Changing the display language............................. 67
[DISPLAY OPTION] menu......................................... 68
[COLOR MATCHING]............................................ 68
[COLOR CORRECTION]...................................... 69
[CONTRAST MODE]............................................. 69
[SCREEN SETTING]............................................. 69
[AUTO SIGNAL].................................................... 70
[AUTO SETUP]..................................................... 70
[RGB IN]................................................................ 70
[DVI-D IN].............................................................. 70
[HDMI IN]............................................................... 71
[ON-SCREEN DISPLAY]....................................... 71
[BACK COLOR]..................................................... 72
[STARTUP LOGO]................................................. 72
[SHUTTER SETTING]........................................... 73
[FREEZE].............................................................. 73
[SIDE BY SIDE](PT-DW740E only)....................... 73
[CUT OFF]............................................................. 74
[PROJECTOR SETUP] menu................................... 75
[PROJECTOR ID].................................................. 75
[PROJECTION METHOD]..................................... 75
[COOLING CONDITION]....................................... 76
[HIGH ALTITUDE MODE]...................................... 76
[LAMP SELECT].................................................... 76
[LAMP RELAY]...................................................... 77
[LAMP POWER].................................................... 77
[STANDBY MODE]................................................ 78
[SCHEDULE]......................................................... 78
[STARTUP INPUT SELECT]................................. 79
[RS-232C].............................................................. 80
[REMOTE2 MODE]............................................... 81
[STATUS]............................................................... 81
[NO SIGNAL SHUT-OFF]...................................... 82
[FUNCTION BUTTON].......................................... 82
[DATE AND TIME]................................................. 83
[SAVE ALL USER DATA]....................................... 83
[LOAD ALL USER DATA]...................................... 84
[INITIALIZE]........................................................... 84
[SERVICE PASSWORD]....................................... 84
[TEST PATTERN] menu............................................ 85
[TEST PATTERN].................................................. 85
[SIGNAL LIST] menu................................................ 86
Registering a signal to the list............................... 86
Renaming the registered data............................... 86
Deleting the registered data.................................. 86
Protecting the registered data............................... 87
Expanding signal lock-in range............................. 87
Managing the sub memory list.............................. 87
12 - ENGLISH
[SECURITY] menu.................................................... 89
[SECURITY PASSWORD]..................................... 89
[SECURITY PASSWORD CHANGE].................... 89
[DISPLAY SETTING]............................................. 89
[TEXT CHANGE]................................................... 90
[MENU LOCK]....................................................... 90
[MENU LOCK PASSWORD]................................. 90
[CONTROL DEVICE SETUP]................................ 90
[NETWORK] menu.................................................... 92
[NETWORK SETUP]............................................. 92
[NETWORK CONTROL]....................................... 92
[NETWORK STATUS]........................................... 93
Network connections............................................. 93
Accessing from the Web browser.......................... 94
Chapter 5 Maintenance
Lamp/Temperature/Filter indicators..................... 110
Managing the indicated problems........................110
Maintenance/replacement..................................... 112
Before maintaining/replacing the unit...................112
Maintenance.........................................................112
Replacing the unit.................................................113
Troubleshooting..................................................... 116
Chapter 6 Appendix
Technical information............................................ 118
PJLink protocol.....................................................118
Control commands via LAN..................................119
<SERIAL IN>/<SERIAL OUT> terminal............... 121
<REMOTE 2 IN> terminal................................... 124
Two window display combination list
(PT-DW740E only)........................................... 125
Menu lock password............................................ 125
List of compatible signals.................................... 125
Specifications......................................................... 128
Dimensions............................................................. 130
Ceiling mount bracket safeguards....................... 131
Index........................................................................ 132
Chapter 1
Preparation
This chapter describes things you need to know or check before using the projector.
ENGLISH - 13
Chapter 1 Preparation — Precautions for use
Precautions for use
Cautions when transporting
ffThe projection lens is susceptible to effects from vibration or impact. Make sure to remove the projection lens when transporting.
Also, use a protection cover or the like to prevent dust from affecting the projection lens or the set.
ffWhen transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. They may damage the internal
parts and result in malfunctions.
ffDo not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.
Cautions when installing
rrAlways attach the projection lens cover after attaching the projection lens.
If the cover is not attached, dust will accumulate inside and may cause malfunctions.
rrDo not set up the projector outdoors.
The projector is designed for indoor use only.
rrDo not set up the projector in the following locations.
ffPlaces where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal parts or malfunction.
ffNear the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare cases due to the hot air from
the air exhaust port or the heated or cooled air. Make sure that the exhaust from the projector or other equipment, or the air from the air
conditioner does not blow toward the front of the projector.
ffNear lights (studio lamps, etc.) and other locations of great temperature fluctuation (“Operating environment” (x page 129)): Doing so may
shorten the life of the lamp or result in deformation of the outer case and malfunctions.
ffNear high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
ffPlace where there is high-power laser equipment: Directing a laser beam onto the lens surface causes damage to the DLP chips.
rrBe sure to ask a specialized technician or your dealer when installing the product to a ceiling.
If the product is to be installed hanging from the ceiling, purchase an optional Ceiling Mount Attachment.
Model No.: ET-PKD56H (for high ceilings), ET-PKD55S (for low ceilings)
rrLens focus
The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in the period just after
switching on the power. Wait at least 30 minutes with the image projected before adjusting the lens focus.
rrMake sure to set [HIGH ALTITUDE MODE] to [ON] when using the projector at elevations of
1 400 m (4 593 ft) or higher and lower than 2 700 m (8 858 ft) above sea level.
Doing so may shorten the life of the internal parts and result in malfunctions.
rrMake sure to set [HIGH ALTITUDE MODE] to [OFF] when using the projector at elevations
lower than 1 400 m (4 593 ft) above sea level.
Doing so may shorten the life of the internal parts and result in malfunctions.
rrDo not install the projector at elevations of 2 700 m (8 858 ft) or higher above sea level.
Doing so may shorten the life of the internal parts and result in malfunctions.
rrDo not use the projector tilted to the right or left
Using the projector at a vertical angle that exceeds 15° may reduce product life or result in malfunction.
rrWhen installing and using the projector at an angle that exceeds 30° vertically, set [COOLING
CONDITION] (x page 76).
Failure to observe this will result in malfunctions or shorten the life of the lamp or other components.
rrCautions when setting up the projector
ffTo install and use the projector via a method that does not use the adjustable feet in a floor standing installation, fix the projector using the
five screw holes for ceiling mounting (Fig. 1).
(Screw diameter: M6, tapping depth inside the set: 12 mm (15/32"), torque: 4 ± 0.5 N·m)
14 - ENGLISH
Chapter 1 Preparation — Precautions for use
ffUse the adjustable feet only for the floor standing installation and for adjusting the angle. Using it for other purposes may damage the set.
Screw holes for ceiling mount (M6)
Adjustable feet
Fig. 1 The positions of screw holes for ceiling mount and adjustable feet
ffDo not stack projectors on top of each other.
ffDo not use the projector tilted at an angle that exceeds ± 15° from the horizontal plane.
ffDo not block the ventilation ports (intake and exhaust) of the projector.
ffPrevent hot and cool air from the air conditioning system from blowing directly to the ventilation ports (intake and exhaust) of the projector.
500 mm (20") or longer
500 mm (20") or longer
500 mm (20") or longer
100 mm (4") or longer
ffDo not install the projector in a confined space.
When it is necessary to install the projector in a confined space, install the air conditioning or ventilation separately. Exhaust heat may
accumulate when the ventilation is not enough, triggering the protection circuit of the projector.
ffMake a clearance of at least 20 mm (0.8") between the projector bottom and setting surface by inserting spacers (metallic) etc. between
them.
Security
When using this product, take safety measures against the following incidents.
ffPersonal information being leaked via this product
ffUnauthorized operation of this product by a malicious third party
ffInterfering or stopping of this product by a malicious third party
Take sufficient security measures. (x pages 89, 104)
ffMake your password difficult to guess as much as possible.
ffChange your password periodically.
ffPanasonic Corporation or its affiliate companies will never ask for your password directly. Do not divulge your password in case you receive
such inquiries.
ffThe connecting network must be secured by a firewall, etc.
ffSet a password for the web control and restrict the users who can log in.
ENGLISH - 15
Chapter 1 Preparation — Precautions for use
Disposal
To dispose of the product, ask your local authorities or dealer for correct methods of disposal.
The lamp contains mercury. When disposing of used lamp units, contact your local authorities or dealer for correct methods of disposal.
Cautions on use
rrTo get a good picture quality
In order to view a beautiful image in higher contrast, prepare an appropriate environment. Draw curtains or blinds over windows and turn off
any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen.
rrDo not touch the surface of the projection lens with your bare hands.
If the surface of the projection lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen.
Please put the lens cover (accessory) on the projector when you do not use it.
rrDLP chips
ffThe DLP chips are precision-made. Note that in rare cases, pixels of high precision could be missing or always lit. Note that such
phenomena does not indicate malfunction. This is not a malfunction.
ffDirecting a high-power laser beam onto the lens surface can damage the DLP chips.
rrDo not move the projector while it is operating or subject it to vibration or impact.
Doing so may shorten the service life of its internal components.
rrLamp
The luminous source of the projector is a high-pressure mercury lamp.
A high-pressure mercury lamp has the following characteristics.
ffThe luminance of the lamp will decrease by duration of usage.
ffThe lamp may burst with a loud sound or have its service life shortened because of shock, chipping, or degradation due to cumulative
operating time.
ffThe lamp life varies greatly depending on individual differences and usage conditions. In particular, frequently switching the power on/off
accelerates lamp deterioration and greatly affects lamp life.
ffContinuous use for one week or longer accelerates lamp deterioration. Lamp relay function (x page 77) can be used to reduce
deterioration caused by continuous use.
ffIn rare cases, the lamps burst shortly after projection starts.
ffThe risk of bursting increases when the lamp is used beyond its replacement cycle. Make sure to replace the lamp unit regularly.
(“When to replace the lamp unit” (x page 114), “Replacing the lamp unit” (x page 114))
ffIf the lamp bursts, gas contained inside of the lamp is released in a form of smoke.
ffIt is recommended that you store replacement lamp units for contingency.
rrAbout connections to computer or peripheral device
ffTo assure continued compliance, follow the attached installation instructions, which include using the provided power cord and shielded
interface cables when connecting to computer or peripheral device.
ffUse a commercial DVI-D cable with a ferrite core.
Software information regarding this product
© Panasonic Corporation 2012
This product incorporates the following software.
(1) The software which is developed independently by or for Panasonic Corporation
(2)The software which is licensed under the GNU GENERAL PUBLIC LICENSE
(3)The software which is licensed under the GNU LESSER GENERAL PUBLIC LICENSE
For the license conditions of software categorized as (2) and (3), refer to the provisions of the Software license (GNU GENERAL PUBLIC
LICENSE and GNU LESSER GENERAL PUBLIC LICENSE) in the supplied CD-ROM. (Those provisions are written in the original (English)
because they have been stipulated by third parties.)
If you have any questions regarding the software, contact ([email protected]) by E-mail.
Pursuant to at the directive 2004/108/EC, article 9(2)
Panasonic Testing Centre
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany
16 - ENGLISH
Chapter 1 Preparation — Precautions for use
Accessories
Make sure that the following accessories are provided with your projector. Numbers enclosed in < > show the number of accessories.
Wireless/wired remote control unit <1>
(N2QAYB000784)
Lens cover <1>
(TKKL5244)
(for models with attached lenses only)
CD-ROM <1>
(TXFQB02VLE3)
Power cord <1>
(K2CM3FZ00003)
Power cord secure lock <1>
(TTRA0183)
Power cord <1>
(K2CT3FZ00003)
AA/R6 battery <2>
Projection lens cover <1>
(TKPB35101)
(For remote control unit)
Attention
ff After unpacking the projector, discard the power cord cap and packaging material properly.
ff For missing accessories, consult your dealer.
ff Store small parts in an appropriate manner, and keep them away from small children.
Note
ff The model numbers of accessories and optional components are subject to change without notice.
Contents of the supplied CD-ROM
The contents of the supplied CD-ROM are as follows.
Instruction/list (PDF)
Operating Instructions - Functional Manual
Multi Projector Monitoring & Control Software Operation Manual
Logo Transfer Software Operating Manual
Software
List of Compatible Projector Models
This is a list of projectors that are compatible with the
software contained in the CD-ROM and their restrictions.
Software license
(GNU GENERAL PUBLIC LICENSE, GNU LESSER
GENERAL PUBLIC LICENSE)
Multi Projector Monitoring & Control Software
(Windows)
This software allows you to monitor and control multiple
projectors connected to the LAN.
Logo Transfer Software (Windows)
This software allows you to create original images, such
as company logos to be displayed when projection starts,
and transfer them to the projector.
ENGLISH - 17
Chapter 1 Preparation — Precautions for use
Optional accessories
Optional accessories (product name)
Model No.
Projection lens
ET-DLE055 (fixed-focus lens), ET-DLE080 (ultra short-focus zoom lens), ET-DLE150 (shortfocus zoom lens), ET-DLE250 (medium-focus zoom lens), ET-DLE350 (long-focus zoom lens),
ET-DLE450 (ultra long-focus zoom lens)
Ceiling mount bracket
ET-PKD56H (for high ceilings), ET-PKD55S (for low ceilings)
Replacement lamp unit
ET-LAD60A (1 pc), ET-LAD60AW (2 pcs)
Replacement filter unit
ET-EMF300
18 - ENGLISH
Chapter 1 Preparation — Start-up display
Start-up display
The initial setting screen is displayed when the projector is switched on for the first time after purchase as well as when [INITIALIZE] – [ALL
USER DATA] (x page 84) is executed. Set them in accordance with circumstances.
In other occasions, you can change the settings by menu operations.
Note
ff When the projector is used for the first time, you may be required to adjust the focus, zoom, and shift to display the menu screen clearly.
Refer to “Adjusting the focus, zoom, and shift” (x page 45) for details.
Initial setting (display language)
Select the language to show on the screen. (x page 67)
1) Press as to select the display language.
,1,7,$/6(77,1*
2) Press the <ENTER> button to proceed to the
initial setting.
3/($6(6(/(&7/$1*8$*(
6(/(&7
(17(5
6(7
Initial setting (projector setup)
Set each item.
1) Press as to select an item.
2) Press qw to switch the setting.
,1,7,$/6(77,1*
352-(&7,210(7+2'
)5217)/225
&22/,1*&21',7,21
)/2256(77,1*
6&5((1)250$7
㧦
ffRefer to the following pages for details.
[PROJECTION METHOD] (x page 75)
[COOLING CONDITION] (x page 76)
[SCREEN FORMAT] (x page 69)
[SCREEN POSITION] (x page 69)
[HIGH ALTITUDE MODE] (x page 76)
3) Press the <ENTER> button.
ffConfirm the setting value to complete the initial setting.
6&5((1326,7,21
+,*+$/7,78'(02'(
2))
6:,7&+72+,*+$/7,78'(02'(21
,)29(5P)W
0(186(/(&7
(17(5
&+$1*(
6(7
Note
ff If you press the <MENU> button in the initial setting (projector setup) screen, you can go back to the initial setting (display language)
screen.
ENGLISH - 19
Chapter 1 Preparation — About your projector
About your projector
Remote control
Front
1
2
3
Top
10
18
4
5
11
6
12
13
7
14
Bottom
19
8
9
15
16
17
1 Remote control indicator
Flashes if any button in the remote control is pressed.
2 Power standby <v> button
Sets the projector to the standby mode when the <MAIN
POWER> switch on the projector is set to <ON>.
3 Power on <b> button
Starts projection when the <MAIN POWER> switch on the
projector is set to <ON> and the power is switched off (standby
mode).
4 Input selection (<RGB1>, <RGB2>, <DVI-D>, <VIDEO>,
<S-VIDEO>, <HDMI>) buttons
Switches the input signal to project. (x page 48)
5 <MENU> button/<ENTER> button/asqw buttons
Used to operate the menu screen. (x page 51)
6 <ON SCREEN> button
Switches the on-screen display function on (displayed)/off
(hidden). (x page 47)
7 <TEST PATTERN> button
Displays the test pattern. (x page 49)
8 Number (<0> - <9>) buttons
Used when the system uses multiple projectors.
Used to input ID numbers or passwords.
9 <STATUS> button
Displays the projector information.
10 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image.
[PROGRESS] is displayed on the screen while the image is
adjusted automatically. (x page 48)
11 <SHUTTER> button
Use to temporarily turn off the image. (x page 47)
12 <ASPECT> button
Switches the aspect ratio of the image. (x page 49)
13 Lens (<FOCUS>, <ZOOM>, <SHIFT>) buttons
Adjusts the projection lens. (x pages 43, 45)
14 <FUNCTION> button
You can assign a frequently used operation as a shortcut button.
(x page 49)
15 <DEFAULT> button
Resets the content of the sub-menu to the factory default.
(x page 51)
16 <ID SET> button
Sets the ID number of the remote control when a system uses
multiple projectors. (x page 23)
17 <ID ALL> button
Use to simultaneously control all the projectors with one remote
control when a system uses multiple projectors. (x page 23)
18 Remote control signal transmitter
19 Remote control wired terminal
Connecting to the projector with a cable
(x page 24)
Attention
ff Do not drop the remote control.
ff Avoid contact with liquids or moisture.
ff Do not attempt to modify or disassemble the remote control.
Note
ff The remote control can be used within a distance of about 30 m (98'5") if pointed directly at the remote control receiver. The remote control
can control at angles of up to ±15° vertically and ±30° horizontally, but the effective control range may be reduced.
ff If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
ff The signal will be reflected off the screen. However, the operating range may be limited from light reflection loss due to the screen material.
ff If the remote control signal receiver directly receives strong light, such as fluorescent light, the remote control may not operate properly.
Use it in a place distant from the light source.
ff The power indicator <ON (G)/STANDBY (R)> will flash if the projector receives a remote control signal.
20 - ENGLISH
Chapter 1 Preparation — About your projector
Projector body
Front
1
2
3
Side
4
5
13
14
13
Front
6
7
8
15 16 17
6
Rear
Front
9
10
11
12
Bottom
13
19
13
18
13
8 Projection lens
(for models with attached lenses only)
9 Air exhaust port
10 Lamp unit cover (x page 114)
11 Control panel (x page 22)
12 Remote control signal receiver (rear)
13 Air intake port
14 Connecting terminals (x page 22)
15 <MAIN POWER> switch
Turns on/off the main power.
Front
13
16 Security slot
This security slot is compatible with the Kensington security
cables.
17 <AC IN> terminal
Connect the supplied power cord.
18 Air filter cover
The air filter unit is inside. (x page 112)
Warning
19 Burglar hook port
You can attach a commercial burglar prevention cable.
Keep your hands and other objects away from the air exhaust
port.
ffKeep your hands and face away.
ffDo not insert your fingers.
ffKeep heat-sensitive objects away.
Heated air from the air outlet port can cause bums, injury, or
deformations.
1 Power indicator <ON (G)/STANDBY (R)>
Displays the status of the power.
2 Lamp indicator <LAMP1>
Displays the status of lamp 1.
3 Lamp indicator <LAMP2>
Displays the status of lamp 2.
4 Temperature indicator <TEMP>
Displays the internal temperature status.
5 Filter indicator <FILTER>
Displays the status of the air filter unit.
6 Adjustable feet
Adjusts the projection angle.
7 Remote control signal receiver (front)
ENGLISH - 21
Chapter 1 Preparation — About your projector
rrControl panel
9
1
2
10
3
4
11
5
6
7
8
12
13
14
9 <MENU> button
Displays and erases the main menu.
Returns to the previous screen when a sub-menu is displayed.
(x page 51)
If you press the <MENU> button on the control panel for at
least three seconds while the on-screen indication is off, the onscreen display is turned on.
1 Power standby <v> button
Sets the projector to the standby mode when the <MAIN
POWER> switch on the projector is set to <ON>.
2 Power on <b> button
Starts projection when the <MAIN POWER> switch on the
projector is set to <ON> when the power is switched off (standby
mode).
10 <LENS> button
Adjusts the focus, zoom, and shift (position) of the lens.
3 <VIDEO> button
Switches to VIDEO input.
11 <ENTER> button
Determines and executes an item in the menu screen.
4 <S-VIDEO> button
Switches to S-VIDEO input.
12 <SHUTTER> button
Use to temporarily turn off the image. (x page 47)
5 <RGB1> button
Switches to RGB1 input.
13 asqw selection buttons
Use to select items in the menu screen, change settings, and
adjust levels.
It is also used to enter [SECURITY] passwords.
6 <RGB2> button
Switches to RGB2 input.
7 <DVI-D> button
Switches to DVI-D input.
14 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image.
[PROGRESS] is displayed on the screen while the image is
adjusted automatically. (x page 48)
8 <HDMI> button
Switches to HDMI input.
rrConnecting terminals
1
2
3
7
4
8
1 <LAN> terminal
This is a terminal to connect to the network.
Used for control and monitoring. Image input through network
connections is not possible.
2 <VIDEO IN> terminal
This is a terminal to input video signals.
3 <S-VIDEO IN> terminal
This is a terminal to input S video signals.
4 <RGB 1 IN> (<R/PR>, <G/Y>, <B/PB>, <SYNC/HD>, <VD>)
terminal
This is a terminal to input RGB signals or YCBCR/YPBPR signals.
5 <HDMI IN> terminal
This is a terminal to input HDMI signals.
6 <DVI-D IN> terminal
This is a terminal to input DVI-D signals.
9
5
10
6
11
7 <REMOTE 1 IN> terminal / <REMOTE 1 OUT> terminal
These are the terminals to connect the remote control for serial
control when the system uses multiple projectors.
8 <REMOTE 2 IN> terminal
This is a terminal to remotely control the projector using the
external control circuit.
9 <SERIAL IN> terminal
This is a RS-232C compatible terminal to externally control the
projector by connecting a computer.
10 <SERIAL OUT> terminal
This is a terminal to output the signal connected to the serial
input terminal.
11 <RGB 2 IN> terminal
This is a terminal to input RGB signals or YCBCR/YPBPR signals.
Attention
ff When a LAN cable is directly connected to the projector, the network connection must be made indoors.
22 - ENGLISH
Chapter 1 Preparation — Using the remote control
Using the remote control
Inserting and removing the batteries
1) Open the cover.
2) Insert the batteries and close the cover (insert
the m side first).
(ii)
(i)
ffWhen removing the batteries, perform the steps in reverse
order.
Setting Remote control ID numbers
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector individually using single
remote control, if a unique ID number is assigned to each projector.
After setting the ID number of the projector, set the same ID number on the remote control.
The factory default ID number of the projector is set to [ALL]. When using a single projector, press the <ID ALL> button on the
remote control. Also, you can control a projector if you press the <ID ALL> button on the remote control even if you do not know the
projector ID.
How to set
1) Press the <ID SET> button on the remote
control.
2) Within five seconds, press the two-digit ID
number set on the projector using the number
(<0> - <9>) buttons.
ffIf you press the <ID ALL> button, you can operate the projectors
regardless of the setting of the projector’s ID number.
Attention
ff Since the ID number of the remote control can be set without the projector, do not press the <ID SET> button carelessly. If the <ID SET>
button is pressed and no number (<0> - <9>) buttons are pressed within the next five seconds, the ID number returns to its original value
before the <ID SET> button was pressed.
ff The ID number set on the remote control will be stored unless it is set again. However, it will be erased if the remote control is left with dead
batteries. Set the same ID number again when the batteries are replaced.
Note
ff Set the ID number of the projector from the [PROJECTOR SETUP] menu → [PROJECTOR ID] (x page 75).
ENGLISH - 23
Chapter 1 Preparation — Using the remote control
Connecting to the projector with a cable
When you use the system with multiple projectors, configure the units as in the following figure. Use a commercial M3 stereo mini jack cable
and connect the other devices to the <REMOTE 1 IN>/<REMOTE 1 OUT> terminals of the projector.
The remote control is effective even in places where an obstacle stands in the light path or where devices are susceptible to outside light.
Connecting terminals
Connect to the second
projector
M3 stereo mini jack cable
(commercially available)
Remote
Connect to remote
control wired terminal
Attention
ff Use a cable that is 15 m (49'2") or shorter, with 2 core shield. The remote control may not operate when the length of the cable exceeds 15
m (49'2") or when the shielding of the cable is inadequate.
24 - ENGLISH
Chapter 2
Getting Started
This chapter describes about things you need to do before using the projector such as the setup and connections.
ENGLISH - 25
Chapter 2 Getting Started — Setting up
Setting up
Projection method
You can use the projector with any of the following four projection methods. Select the appropriate method depending on the environment.
Mounting on the ceiling and projecting forward
Menu item*
Setting on a desk/floor and projecting from rear
(Using the translucent screen)
Method
Menu item*
[PROJECTION METHOD]
[FRONT/CEILING]
[PROJECTION METHOD]
[REAR/FLOOR]
[COOLING CONDITION]
[CEILING SETTING]
[COOLING CONDITION]
[FLOOR SETTING]
Mounting on the ceiling and projecting from rear
(Using the translucent screen)
Menu item*
Method
Setting on a desk/floor and projecting forward
Method
Menu item*
Method
[PROJECTION METHOD]
[REAR/CEILING]
[PROJECTION METHOD]
[FRONT/FLOOR]
[COOLING CONDITION]
[CEILING SETTING]
[COOLING CONDITION]
[FLOOR SETTING]
*For menu item details, refer to the [PROJECTOR SETUP] menu → [PROJECTION METHOD] (x page 75) and [COOLING CONDITION]
(x page 76).
Parts for ceiling mount (optional)
You can install the projector on the ceiling using the optional ceiling mount bracket (ET-PKD56H: for high ceilings, or ET-PKD55S: for low
ceilings).
ffUse only the ceiling mount brackets specified for this projector.
ffRefer to the installation manual for the ceiling mount bracket when installing the bracket and the projector.
Attention
ff To ensure projector performance and security, installation of the ceiling mount bracket must be carried out by your dealer or a qualified
technician.
26 - ENGLISH
Chapter 2 Getting Started — Setting up
Screen size and throw distance
Refer to the following figures and table describing projection distances to install the projector. Image size and image position can be adjusted
in accordance with the screen size and screen position.
Projection screen
SH
Screen
L (LW/LT)
H
SH
SD
SW
SW
L (LW/LT)
Screen
L (LW/LT)*
Projection distance (m)
SH
Image height (m)
SW
Image width (m)
H
SD
Distance (m) from the lens center to the bottom edge of the image
Image diagonal size (m)
*LW: Minimum projection distance when the zoom lens is used
LT: Maximum projection distance when the zoom lens is used
Attention
ffBefore setting up, read “Precautions for use” (x pages 14 to 18).
ffDo not use the projector and the high-powered laser equipment in the same room.
Hitting of a laser beam on to the lens can damage the DLP chips.
ENGLISH - 27
Chapter 2 Getting Started — Setting up
Projection distance per projection lens
For PT-DW740E
rrWhen the screen aspect is 16:10 (unit: m)
(The dimensions of the following table contain slight error.)
Optional lens
Standard zoom lens
Fixedfocus
lens
Ultra-short focus
zoom lens
Projection lens Model No.
―
ET-DLE055
ET-DLE080
ET-DLE150
ET-DLE250
Throw ratio*1
1.8 – 2.5:1
0.8:1
0.8 – 1.0:1
1.4 – 2.0:1
2.4 – 3.8:1
Lens type
Projection screen size
Short focus zoom Medium focus zoom
lens
lens
Projection distance (L)
Screen diagonal
(SD)
Height
(SH)
Width
(SW)
Min.
Max.
Fixed
Min.
Max.
Min.
Max.
Min.
Max.
1.27 (50")
0.673
1.077
1.91
2.70
0.87
0.87
1.09
1.45
2.12
2.54
4.06
1.52 (60")
0.808
1.292
2.31
3.26
1.06
1.05
1.32
1.75
2.55
3.07
4.89
1.78 (70")
0.942
1.508
2.71
3.81
1.24
1.23
1.54
2.05
2.98
3.59
5.72
2.03 (80")
1.077
1.723
3.11
4.37
1.42
1.42
1.77
2.35
3.42
4.12
6.55
2.29 (90")
1.212
1.939
3.50
4.92
1.61
1.60
2.00
2.65
3.85
4.64
7.38
2.54 (100")
1.346
2.154
3.90
5.48
1.79
1.78
2.22
2.95
4.28
5.16
8.20
3.05 (120")
1.615
2.585
4.70
6.59
2.16
2.15
2.68
3.55
5.15
6.21
9.86
3.81 (150")
2.019
3.231
5.89
8.25
2.71
2.70
3.36
4.45
6.45
7.79
12.35
5.08 (200")
2.692
4.308
7.88
11.03
3.63
3.61
4.49
5.95
8.61
10.41
16.49
6.35 (250")
3.365
5.385
9.86
13.81
―
4.53
5.62
7.45
10.78
13.03
20.63
7.62 (300")
4.039
6.462
11.85
16.58
―
5.45
6.76
8.95
12.95
15.65
24.77
8.89 (350")
4.712
7.539
13.84
19.36
―
6.36
7.89
10.46
15.11
18.28
28.91
10.16 (400")
5.385
8.616
15.83
22.13
―
7.28
9.02
11.96
17.28
20.90
33.05
12.7 (500")
6.731
10.770
19.80
27.68
―
9.11
11.29
14.96
21.61
26.14
41.34
15.24 (600")
8.077
12.923
23.78
33.23
―
10.94
13.55
17.96
25.94
31.39
49.62
Optional lens
Lens type
Projection lens Model No.
Throw ratio
*1
Long focus zoom
lens
Ultra-long focus
zoom lens
ET-DLE350
ET-DLE450
3.8 – 5.7:1
5.6 – 9.0:1
Projection screen size
Projection distance (L)
Screen diagonal
(SD)
Height
(SH)
Width
(SW)
Min.
1.27 (50")
0.673
1.077
1.52 (60")
0.808
1.292
1.78 (70")
0.942
2.03 (80")
Max.
Height position
(H)*2
Standard zoom
lens/
ET-DLE080/
ET-DLE150/
ET-DLE250/
ET-DLE350/
ET-DLE450
ET-DLE055
(Fixed)
Max.
Min.
4.00
6.11
5.96
9.59
-0.07 - 0.34
0.34
4.83
7.36
7.21
11.57
-0.08 - 0.40
0.40
1.508
5.65
8.61
8.46
13.55
-0.09 - 0.47
0.47
1.077
1.723
6.48
9.86
9.71
15.53
-0.11 - 0.54
0.54
2.29 (90")
1.212
1.939
7.31
11.11
10.96
17.51
-0.12 - 0.61
0.61
2.54 (100")
1.346
2.154
8.13
12.36
12.21
19.49
-0.13 - 0.67
0.67
3.05 (120")
1.615
2.585
9.79
14.86
14.72
23.45
-0.16 - 0.81
0.81
3.81 (150")
2.019
3.231
12.27
18.61
18.47
29.38
-0.20 - 1.01
1.01
5.08 (200")
2.692
4.308
16.40
24.85
24.73
39.28
-0.27 - 1.35
1.35
6.35 (250")
3.365
5.385
20.53
31.10
30.99
49.17
-0.34 - 1.68
―
7.62 (300")
4.039
6.462
24.67
37.34
37.25
59.06
-0.40 - 2.02
―
8.89 (350")
4.712
7.539
28.80
43.59
43.51
68.96
-0.47 - 2.36
―
10.16 (400")
5.385
8.616
32.94
49.84
49.76
78.85
-0.54 - 2.69
―
12.7 (500")
6.731
10.770
41.20
62.33
62.28
98.64
-0.67 - 3.37
―
15.24 (600")
8.077
12.923
49.47
74.82
74.80
118.42
-0.81 - 4.04
―
*1 The throw ratio is based on the value during projection onto a 2.03-m (80") screen size.
*2 The height position (H) is SH/2 because lens shift cannot be used when a fixed-focus lens (Model No.:ET-DLE055) is attached.
28 - ENGLISH
Chapter 2 Getting Started — Setting up
rrWhen the screen aspect is 16:9 (unit: m)
(The dimensions of the following table contain slight error.)
Optional lens
Standard zoom lens
Fixedfocus
lens
Ultra-short focus
zoom lens
Projection lens Model No.
―
ET-DLE055
ET-DLE080
ET-DLE150
ET-DLE250
Throw ratio*1
1.8 – 2.5:1
0.8:1
0.8 – 1.0:1
1.4 – 2.0:1
2.4 – 3.8:1
Lens type
Projection screen size
Short focus zoom Medium focus zoom
lens
lens
Projection distance (L)
Screen diagonal
(SD)
Height
(SH)
Width
(SW)
Min.
Max.
Fixed
Min.
Max.
Min.
Max.
Min.
Max.
1.27 (50")
0.623
1.107
1.97
2.78
0.90
0.89
1.12
1.49
2.18
2.62
4.18
1.52 (60")
0.747
1.328
2.38
3.35
1.09
1.08
1.35
1.80
2.62
3.15
5.03
1.78 (70")
0.872
1.550
2.79
3.92
1.27
1.27
1.59
2.11
3.07
3.69
5.88
2.03 (80")
0.996
1.771
3.19
4.49
1.46
1.46
1.82
2.42
3.51
4.23
6.73
2.29 (90")
1.121
1.992
3.60
5.06
1.65
1.65
2.05
2.72
3.96
4.77
7.58
2.54 (100")
1.245
2.214
4.01
5.63
1.84
1.83
2.29
3.03
4.40
5.31
8.43
3.05 (120")
1.494
2.657
4.83
6.77
2.22
2.21
2.75
3.65
5.29
6.39
10.14
3.81 (150")
1.868
3.321
6.05
8.49
2.79
2.78
3.45
4.58
6.63
8.01
12.69
5.08 (200")
2.491
4.428
8.10
11.34
3.73
3.72
4.61
6.12
8.86
10.70
16.95
6.35 (250")
3.113
5.535
10.14
14.19
―
4.66
5.78
7.66
11.08
13.40
21.21
7.62 (300")
3.736
6.641
12.18
17.04
―
5.60
6.94
9.21
13.31
16.09
25.46
8.89 (350")
4.358
7.748
14.23
19.90
―
6.54
8.11
10.75
15.53
18.79
29.72
10.16 (400")
4.981
8.855
16.27
22.75
―
7.48
9.27
12.29
17.76
21.48
33.98
12.7 (500")
6.226
11.069
20.35
28.45
―
9.36
11.60
15.38
22.21
26.87
42.49
15.24 (600")
7.472
13.283
24.44
34.16
―
11.24
13.93
18.46
26.66
32.26
51.00
Optional lens
Lens type
Long focus zoom
lens
Ultra-long focus
zoom lens
Projection lens Model No.
ET-DLE350
ET-DLE450
Throw ratio*1
3.8 – 5.7:1
5.6 – 9.0:1
Projection screen size
Projection distance (L)
Screen diagonal
(SD)
Height
(SH)
Width
(SW)
1.27 (50")
0.623
1.52 (60")
0.747
1.78 (70")
Max.
Height position
(H)*2
Standard zoom
lens/
ET-DLE080/
ET-DLE150/
ET-DLE250/
ET-DLE350/
ET-DLE450
ET-DLE055
(Fixed)
Min.
Max.
Min.
1.107
4.11
6.29
6.13
9.87
-0.14 - 0.31
0.31
1.328
4.96
7.57
7.42
11.90
-0.16 - 0.37
0.37
0.872
1.550
5.81
8.85
8.70
13.94
-0.19 - 0.44
0.44
2.03 (80")
0.996
1.771
6.66
10.14
9.99
15.97
-0.22 - 0.50
0.50
2.29 (90")
1.121
1.992
7.51
11.42
11.28
18.00
-0.25 - 0.56
0.56
2.54 (100")
1.245
2.214
8.36
12.71
12.56
20.04
-0.27 - 0.62
0.62
3.05 (120")
1.494
2.657
10.06
15.27
15.14
24.11
-0.33 - 0.75
0.75
3.81 (150")
1.868
3.321
12.61
19.13
18.99
30.21
-0.41 - 0.93
0.93
5.08 (200")
2.491
4.428
16.86
25.55
25.43
40.38
-0.55 - 1.25
1.25
6.35 (250")
3.113
5.535
21.11
31.97
31.86
50.54
-0.68 - 1.56
―
7.62 (300")
3.736
6.641
25.36
38.39
38.29
60.71
-0.82 - 1.87
―
8.89 (350")
4.358
7.748
29.61
44.81
44.72
70.88
-0.96 - 2.18
―
10.16 (400")
4.981
8.855
33.86
51.23
51.16
81.05
-1.10 - 2.49
―
12.7 (500")
6.226
11.069
42.35
64.07
64.02
101.39
-1.37 - 3.11
―
15.24 (600")
7.472
13.283
50.85
76.91
76.88
121.73
-1.64 - 3.74
―
*1 The throw ratio is based on the value during projection onto a 2.03-m (80") screen size.
*2 The height position (H) is SH/2 because lens shift cannot be used when a fixed-focus lens (Model No.:ET-DLE055) is attached.
ENGLISH - 29
Chapter 2 Getting Started — Setting up
rrWhen the screen aspect is 4:3 (unit: m)
(The dimensions of the following table contain slight error.)
Optional lens
Standard zoom lens
Fixedfocus
lens
Ultra-short focus
zoom lens
Projection lens Model No.
―
ET-DLE055
ET-DLE080
ET-DLE150
ET-DLE250
Throw ratio*1
2.2 – 3.0:1
1.0:1
1.0 – 1.2:1
1.6 – 2.4:1
2.9 – 4.6:1
Lens type
Projection screen size
Short focus zoom Medium focus zoom
lens
lens
Projection distance (L)
Screen diagonal
(SD)
Height
(SH)
Width
(SW)
Min.
Max.
Fixed
Min.
Max.
Min.
Max.
Min.
Max.
1.27 (50")
0.762
1.016
2.18
3.07
0.99
0.99
1.24
1.65
2.40
2.89
4.61
1.52 (60")
0.914
1.219
2.63
3.70
1.20
1.20
1.50
1.99
2.89
3.48
5.55
1.78 (70")
1.067
1.422
3.08
4.33
1.41
1.40
1.75
2.33
3.38
4.08
6.48
2.03 (80")
1.219
1.626
3.53
4.95
1.62
1.61
2.01
2.67
3.87
4.67
7.42
2.29 (90")
1.372
1.829
3.98
5.58
1.82
1.82
2.26
3.00
4.36
5.26
8.36
2.54 (100")
1.524
2.032
4.42
6.21
2.03
2.03
2.52
3.34
4.85
5.86
9.30
3.05 (120")
1.829
2.438
5.32
7.47
2.45
2.44
3.03
4.02
5.83
7.04
11.17
3.81 (150")
2.286
3.048
6.67
9.35
3.07
3.06
3.80
5.04
7.31
8.82
13.98
5.08 (200")
3.048
4.064
8.92
12.49
4.11
4.10
5.09
6.74
9.76
11.79
18.67
6.35 (250")
3.810
5.080
11.17
15.64
―
5.13
6.37
8.44
12.21
14.76
23.36
7.62 (300")
4.572
6.096
13.42
18.78
―
6.17
7.65
10.14
14.66
17.73
28.05
8.89 (350")
5.334
7.112
15.67
21.92
―
7.21
8.93
11.84
17.11
20.70
32.74
10.16 (400")
6.096
8.128
17.92
25.06
―
8.24
10.22
13.54
19.56
23.67
37.42
12.7 (500")
7.620
10.160
22.42
31.34
―
10.31
12.78
16.94
24.47
29.60
46.80
15.24 (600")
9.144
12.192
26.92
37.63
―
12.39
15.35
20.34
29.37
35.54
56.17
Optional lens
Lens type
Long focus zoom
lens
Projection lens Model No.
ET-DLE350
ET-DLE450
Throw ratio*1
4.5 – 6.9:1
6.8 – 10.8:1
Projection screen size
Ultra-long focus
zoom lens
Projection distance (L)
Height position
(H)*2
Standard zoom
lens/
ET-DLE080/
ET-DLE150/
ET-DLE250/
ET-DLE350/
ET-DLE450
ET-DLE055
(Fixed)
Screen diagonal
(SD)
Height
(SH)
Width
(SW)
Min.
Max.
Min.
Max.
1.27 (50")
0.762
1.016
4.54
6.94
6.78
10.90
-0.08 - 0.38
0.38
1.52 (60")
0.914
1.219
5.48
8.35
8.20
13.14
-0.09 - 0.46
0.46
1.78 (70")
1.067
1.422
6.42
9.76
9.61
15.38
-0.11 - 0.53
0.53
2.03 (80")
1.219
1.626
7.35
11.18
11.03
17.62
-0.12 - 0.61
0.61
2.29 (90")
1.372
1.829
8.29
12.59
12.45
19.86
-0.14 - 0.69
0.69
2.54 (100")
1.524
2.032
9.22
14.01
13.87
22.10
-0.15 - 0.76
0.76
3.05 (120")
1.829
2.438
11.09
16.83
16.70
26.58
-0.18 - 0.91
0.91
3.81 (150")
2.286
3.048
13.90
21.08
20.95
33.30
-0.23 - 1.14
1.14
5.08 (200")
3.048
4.064
18.58
28.15
28.03
44.49
-0.30 - 1.52
1.52
6.35 (250")
3.810
5.080
23.26
35.22
35.12
55.69
-0.38 - 1.91
―
7.62 (300")
4.572
6.096
27.94
42.29
42.20
66.89
-0.46 - 2.29
―
8.89 (350")
5.334
7.112
32.62
49.36
49.28
78.09
-0.53 - 2.67
―
10.16 (400")
6.096
8.128
37.30
56.43
56.37
89.29
-0.61 - 3.05
―
12.7 (500")
7.620
10.160
46.65
70.57
70.53
111.68
-0.76 - 3.81
―
15.24 (600")
9.144
12.192
56.01
84.71
84.70
134.08
-0.91 - 4.57
―
*1 The throw ratio is based on the value during projection onto a 2.03-m (80") screen size.
*2 The height position (H) is SH/2 because lens shift cannot be used when a fixed-focus lens (Model No.:ET-DLE055) is attached.
30 - ENGLISH
Chapter 2 Getting Started — Setting up
For PT-DX810E
rrWhen the screen aspect is 4:3 (unit: m)
(The dimensions of the following table contain slight error.)
Optional lens
Standard zoom lens
Fixedfocus
lens
Ultra-short focus
zoom lens
Projection lens Model No.
―
ET-DLE055
ET-DLE080
ET-DLE150
ET-DLE250
Throw ratio*1
1.8 – 2.5:1
0.8:1
0.8 – 1.0:1
1.3 – 2.0:1
2.4 – 3.7:1
Lens type
Projection screen size
Short focus zoom Medium focus zoom
lens
lens
Projection distance (L)
Screen diagonal
(SD)
Height
(SH)
Width
(SW)
Min.
Max.
Fixed
Min.
Max.
Min.
Max.
Min.
Max.
1.27 (50")
0.762
1.016
1.78
2.51
0.81
0.81
1.01
1.34
1.97
2.36
3.78
1.52 (60")
0.914
1.219
2.15
3.03
0.98
0.98
1.22
1.62
2.37
2.85
4.55
1.78 (70")
1.067
1.422
2.52
3.55
1.15
1.15
1.43
1.90
2.77
3.34
5.32
2.03 (80")
1.219
1.626
2.89
4.06
1.32
1.32
1.64
2.18
3.18
3.83
6.09
2.29 (90")
1.372
1.829
3.26
4.58
1.49
1.49
1.85
2.46
3.58
4.31
6.86
2.54 (100")
1.524
2.032
3.63
5.10
1.66
1.66
2.07
2.74
3.98
4.80
7.63
3.05 (120")
1.829
2.438
4.37
6.13
2.01
2.00
2.49
3.30
4.79
5.78
9.17
3.81 (150")
2.286
3.048
5.48
7.68
2.52
2.51
3.12
4.14
6.00
7.24
11.49
5.08 (200")
3.048
4.064
7.33
10.26
3.38
3.36
4.18
5.54
8.02
9.69
15.34
6.35 (250")
3.810
5.080
9.18
12.85
―
4.21
5.23
6.94
10.03
12.13
19.20
7.62 (300")
4.572
6.096
11.03
15.43
―
5.07
6.29
8.33
12.05
14.57
23.06
8.89 (350")
5.334
7.112
12.88
18.02
―
5.92
7.34
9.73
14.07
17.01
26.91
10.16 (400")
6.096
8.128
14.73
20.60
―
6.77
8.40
11.13
16.08
19.45
30.77
12.7 (500")
7.620
10.160
18.43
25.77
―
8.48
10.51
13.92
20.12
24.33
38.48
15.24 (600")
9.144
12.192
22.13
30.94
―
10.18
12.62
16.72
24.15
29.22
46.19
Optional lens
Lens type
Long focus zoom
lens
Ultra-long focus
zoom lens
Projection lens Model No.
ET-DLE350
ET-DLE450
Throw ratio*1
3.7 – 5.6:1
5.5 – 8.9:1
Projection screen size
Projection distance (L)
Height position
(H)*2
Standard zoom
lens/
ET-DLE150/
ET-DLE250/
ET-DLE350/
ET-DLE450
ET-DLE080
ET-DLE055
(Fixed)
Screen diagonal
(SD)
Height
(SH)
Width
(SW)
Min.
Max.
Min.
1.27 (50")
0.762
1.016
3.71
5.68
5.52
8.91
0 - 0.38
0.04 - 0.38
0.38
1.52 (60")
0.914
1.219
4.48
6.84
6.69
10.75
0 - 0.46
0.05 - 0.46
0.46
1.78 (70")
1.067
1.422
5.25
8.01
7.86
12.60
0 - 0.53
0.05 - 0.53
0.53
2.03 (80")
1.219
1.626
6.02
9.17
9.02
14.44
0 - 0.61
0.06 - 0.61
0.61
2.29 (90")
1.372
1.829
6.79
10.33
10.19
16.28
0 - 0.69
0.07 - 0.69
0.69
2.54 (100")
1.524
2.032
7.56
11.50
11.35
18.12
0 - 0.76
0.08 - 0.76
0.76
3.05 (120")
1.829
2.438
9.10
13.82
13.68
21.81
0 - 0.91
0.09 - 0.91
0.91
3.81 (150")
2.286
3.048
11.41
17.31
17.18
27.33
0 - 1.14
0.11 - 1.14
1.14
5.08 (200")
3.048
4.064
15.26
23.13
23.00
36.54
0 - 1.52
0.15 - 1.52
1.52
6.35 (250")
3.810
5.080
19.11
28.94
28.83
45.75
0 - 1.91
0.19 - 1.91
―
7.62 (300")
4.572
6.096
22.96
34.76
34.66
54.97
0 - 2.29
0.23 - 2.29
―
8.89 (350")
5.334
7.112
26.80
40.57
40.48
64.18
0 - 2.67
0.27 - 2.67
―
10.16 (400")
6.096
8.128
30.65
46.39
46.31
73.39
0 - 3.05
0.30 - 3.05
―
12.7 (500")
7.620
10.160
38.35
58.02
57.96
91.81
0 - 3.81
0.38 - 3.81
―
15.24 (600")
9.144
12.192
46.05
69.65
69.61
110.23
0 - 4.57
0.46 - 4.57
―
Max.
*1 The throw ratio is based on the value during projection onto a 2.03-m (80") screen size.
*2 The height position (H) is SH/2 because lens shift cannot be used when a fixed-focus lens (Model No.:ET-DLE055) is attached.
ENGLISH - 31
Chapter 2 Getting Started — Setting up
rrWhen the screen aspect is 16:9 (unit: m)
(The dimensions of the following table contain slight error.)
Optional lens
Standard zoom lens
Fixedfocus
lens
Ultra-short focus
zoom lens
Projection lens Model No.
―
ET-DLE055
ET-DLE080
ET-DLE150
ET-DLE250
Throw ratio*1
1.8 – 2.5:1
0.8:1
0.8 – 1.0:1
1.3 – 2.0:1
2.4 – 3.8:1
Lens type
Projection screen size
Short focus zoom Medium focus zoom
lens
lens
Projection distance (L)
Screen diagonal
(SD)
Height
(SH)
Width
(SW)
Min.
Max.
Fixed
Min.
1.27 (50")
0.623
1.107
1.94
2.74
0.88
1.52 (60")
0.747
1.328
2.34
3.31
1.07
1.78 (70")
0.872
1.550
2.75
3.87
2.03 (80")
0.996
1.771
3.15
4.43
2.29 (90")
1.121
1.992
3.55
2.54 (100")
1.245
2.214
3.05 (120")
1.494
3.81 (150")
5.08 (200")
Max.
Min.
Max.
Min.
Max.
0.88
1.11
1.47
2.15
2.58
4.12
1.07
1.34
1.77
2.59
3.11
4.96
1.26
1.25
1.57
2.08
3.03
3.64
5.80
1.44
1.44
1.79
2.38
3.47
4.18
6.64
4.99
1.63
1.62
2.02
2.69
3.90
4.71
7.48
3.96
5.56
1.82
1.81
2.25
2.99
4.34
5.24
8.32
2.657
4.76
6.68
2.19
2.18
2.71
3.60
5.22
6.30
10.00
1.868
3.321
5.97
8.37
2.75
2.74
3.40
4.51
6.54
7.90
12.52
2.491
4.428
7.99
11.19
3.68
3.67
4.55
6.04
8.74
10.56
16.72
6.35 (250")
3.113
5.535
10.01
14.00
―
4.60
5.70
7.56
10.93
13.22
20.93
7.62 (300")
3.736
6.641
12.02
16.82
―
5.52
6.85
9.08
13.13
15.88
25.13
8.89 (350")
4.358
7.748
14.04
19.63
―
6.45
8.00
10.61
15.33
18.54
29.33
10.16 (400")
4.981
8.855
16.05
22.45
―
7.38
9.15
12.13
17.53
21.20
33.53
12.7 (500")
6.226
11.069
20.09
28.08
―
9.24
11.45
15.17
21.92
26.52
41.93
15.24 (600")
7.472
13.283
24.12
33.71
―
11.10
13.75
18.22
26.31
31.84
50.33
Optional lens
Lens type
Long focus
zoom lens
Ultra-long focus
zoom lens
Projection lens Model No.
ET-DLE350
ET-DLE450
Throw ratio*1
3.7 – 5.6:1
5.6 – 8.9:1
Projection screen size
Projection distance (L)
Height position
(H)*2
Standard zoom
lens/
ET-DLE150/
ET-DLE250/
ET-DLE350/
ET-DLE450
ET-DLE080
ET-DLE055
(Fixed)
Screen diagonal
(SD)
Height
(SH)
Width
(SW)
Min.
Max.
Min.
1.27 (50")
0.623
1.107
4.06
6.20
6.05
9.74
-0.21 - 0.31
-0.16 - 0.31
0.31
1.52 (60")
0.747
1.328
4.90
7.47
7.32
11.74
-0.25 - 0.37
-0.19 - 0.37
0.37
Max.
1.78 (70")
0.872
1.550
5.73
8.74
8.58
13.75
-0.29 - 0.44
-0.23 - 0.44
0.44
2.03 (80")
0.996
1.771
6.57
10.00
9.85
15.76
-0.33 - 0.50
-0.26 - 0.50
0.50
2.29 (90")
1.121
1.992
7.41
11.27
11.12
17.76
-0.37 - 0.56
-0.29 - 0.56
0.56
2.54 (100")
1.245
2.214
8.25
12.54
12.39
19.77
-0.41 - 0.62
-0.32 - 0.62
0.62
0.75
3.05 (120")
1.494
2.657
9.93
15.07
14.93
23.78
-0.49 - 0.75
-0.39 - 0.75
3.81 (150")
1.868
3.321
12.44
18.87
18.74
29.81
-0.62 - 0.93
-0.49 - 0.93
0.93
5.08 (200")
2.491
4.428
16.64
25.21
25.09
39.84
-0.82 - 1.25
-0.65 - 1.25
1.25
6.35 (250")
3.113
5.535
20.83
31.54
31.44
49.88
-1.03 - 1.56
-0.81 - 1.56
―
7.62 (300")
3.736
6.641
25.02
37.88
37.78
59.91
-1.23 - 1.87
-0.97 - 1.87
―
8.89 (350")
4.358
7.748
29.22
44.22
44.13
69.95
-1.44 - 2.18
-1.13 - 2.18
―
10.16 (400")
4.981
8.855
33.41
50.55
50.48
79.98
-1.64 - 2.49
-1.30 - 2.49
―
12.7 (500")
6.226
11.069
41.79
63.22
63.17
100.05
-2.05 - 3.11
-1.62 - 3.11
―
15.24 (600")
7.472
13.283
50.18
75.89
75.87
120.12
-2.47 - 3.74
-1.94 - 3.74
―
*1 The throw ratio is based on the value during projection onto a 2.03-m (80") screen size.
*2 The height position (H) is SH/2 because lens shift cannot be used when a fixed-focus lens (Model No.:ET-DLE055) is attached.
32 - ENGLISH
Chapter 2 Getting Started — Setting up
Projection distance formulas by projection lens
To use a screen size not listed in this manual, check the screen size SD and use the following formula to calculate projection distance.
The unit of the calculation result is m.
For PT-DW740E
Lens type
Projection lens Model No.
Aspect ratio
16:10
Standard zoom lens
―
16:9
4:3
Fixed-focus lens
ET-DLE055
16:9
16:9
16:9
4:3
16:10
Long focus zoom lens
ET-DLE350
16:9
4:3
16:10
Ultra-long focus zoom lens
ET-DLE450
L = 2.4724 x SD (m) – 0.0725
L = 0.7244 x SD (m) – 0.0476
16:10
ET-DLE250
L = 1.7717 x SD (m) – 0.0746
Max. (LT)
L = 0.7441 x SD (m) – 0.0476
4:3
Medium focus zoom lens
L = 2.2480 x SD (m) – 0.0725
Min. (LW)
―
16:10
ET-DLE150
L = 1.6102 x SD (m) – 0.0746
Max. (LT)
―
4:3
Short focus zoom lens
L = 2.1850 x SD (m) – 0.0725
Min. (LW)
16:9
16:10
ET-DLE080
L = 1.5669 x SD (m) – 0.0746
Max. (LT)
16:10
4:3
Ultra-short focus zoom
lens
Projection distance (L) formula
Min. (LW)
16:9
4:3
―
L = 0.8189 x SD (m) – 0.0476
Min. (LW)
L = 0.7205 x SD (m) – 0.0471
Max. (LT)
L = 0.8937 x SD (m) – 0.0442
Min. (LW)
L = 0.7402 x SD (m) – 0.0471
Max. (LT)
L = 0.9173 x SD (m) – 0.0442
Min. (LW)
L = 0.8150 x SD (m) – 0.0471
Max. (LT)
L = 1.0118 x SD (m) – 0.0442
Min. (LW)
L = 1.1811 x SD (m) – 0.0540
Max. (LT)
L = 1.7047 x SD (m) – 0.0498
Min. (LW)
L = 1.2165 x SD (m) – 0.0540
Max. (LT)
L = 1.7520 x SD (m) – 0.0498
Min. (LW)
L = 1.3386 x SD (m) – 0.0540
Max. (LT)
L = 1.9291 x SD (m) – 0.0498
Min. (LW)
L = 2.0630 x SD (m) – 0.0800
Max. (LT)
L = 3.2598 x SD (m) – 0.0792
Min. (LW)
L = 2.1220 x SD (m) – 0.0800
Max. (LT)
L = 3.3504 x SD (m) – 0.0792
Min. (LW)
L = 2.3386 x SD (m) – 0.0800
Max. (LT)
L = 3.6929 x SD (m) – 0.0792
Min. (LW)
L = 3.2559 x SD (m) – 0.1351
Max. (LT)
L = 4.9173 x SD (m) – 0.1346
Min. (LW)
L = 3.3465 x SD (m) – 0.1351
Max. (LT)
L = 5.0551 x SD (m) – 0.1346
Min. (LW)
L = 3.6850 x SD (m) – 0.1351
Max. (LT)
L = 5.5669 x SD (m) – 0.1346
Min. (LW)
L = 4.9291 x SD (m) – 0.3017
Max. (LT)
L = 7.7913 x SD (m) – 0.2991
Min. (LW)
L = 5.0630 x SD (m) – 0.3017
Max. (LT)
L = 8.0079 x SD (m) – 0.2991
Min. (LW)
L = 5.5787 x SD (m) – 0.3017
Max. (LT)
L = 8.8189 x SD (m) – 0.2991
For PT-DX810E
Lens type
Projection lens Model No.
Aspect ratio
4:3
Standard zoom lens
―
16:9
Fixed-focus lens
ET-DLE055
Projection distance (L) formula
Min. (LW)
L = 1.4567 x SD (m) – 0.0746
Max. (LT)
L = 2.0354 x SD (m) – 0.0725
Min. (LW)
L = 1.5866 x SD (m) – 0.0746
Max. (LT)
L = 2.2165 x SD (m) – 0.0725
4:3
―
L = 0.6732 x SD (m) – 0.0476
16:9
―
L = 0.7323 x SD (m) – 0.0476
ENGLISH - 33
Chapter 2 Getting Started — Setting up
Lens type
Ultra-short focus zoom
lens
Projection lens Model No.
Aspect ratio
4:3
ET-DLE080
16:9
4:3
Short focus zoom lens
ET-DLE150
16:9
4:3
Medium focus zoom lens
ET-DLE250
16:9
4:3
Long focus zoom lens
ET-DLE350
16:9
4:3
Ultra-long focus zoom lens
ET-DLE450
16:9
Projection distance (L) formula
Min. (LW)
L = 0.6693 x SD (m) – 0.0471
Max. (LT)
L = 0.8307 x SD (m) – 0.0442
Min. (LW)
L = 0.7323 x SD (m) – 0.0471
Max. (LT)
L = 0.9055 x SD (m) – 0.0442
Min. (LW)
L = 1.1024 x SD (m) – 0.0540
Max. (LT)
L = 1.5866 x SD (m) – 0.0498
Min. (LW)
L = 1.2008 x SD (m) – 0.0540
Max. (LT)
L = 1.7283 x SD (m) – 0.0498
Min. (LW)
L = 1.9213 x SD (m) – 0.0800
Max. (LT)
L = 3.0354 x SD (m) – 0.0792
Min. (LW)
L = 2.0945 x SD (m) – 0.0800
Max. (LT)
L = 3.3071 x SD (m) – 0.0792
Min. (LW)
L = 3.0315 x SD (m) – 0.1351
Max. (LT)
L = 4.5787 x SD (m) – 0.1346
Min. (LW)
L = 3.3031 x SD (m) – 0.1351
Max. (LT)
L = 4.9882 x SD (m) – 0.1346
Min. (LW)
L = 4.5866 x SD (m) – 0.3017
Max. (LT)
L = 7.2520 x SD (m) – 0.2991
Min. (LW)
L = 5.0000 x SD (m) – 0.3017
Max. (LT)
L = 7.9016 x SD (m) – 0.2991
Adjusting adjustable feet
Install the projector on a flat surface so that the front of the projector is parallel to the screen surface and the projection screen is rectangular.
If the screen is tilted downward, the projection screen can be adjusted to be rectangular by adjusting the adjustable feet. The adjustable feet
can also be used to adjust the projector to be level when it is tilted in a horizontal direction.
Extend the adjustable feet by rotating in the direction shown in the figure and retract by rotating in the opposite direction.
Adjustable amount
Front adjustable feet: 30 mm (1-3/16")
Attention
ff Hot air is expelled from the air exhaust port when the lamp is on. Do not touch the air exhaust port directly when adjusting the adjustable
feet. (x page 21)
34 - ENGLISH
Chapter 2 Getting Started — Removing/attaching the projection lens
Removing/attaching the projection lens
Attach and remove the projection lens in the same way as a standard zoom lens and optional accessories.
Move the projection lens to the home position before replacing or removing the lens (x page 46).
Attention
ffReplace the projection lens after turning off the power of the projector.
ffDo not touch the lens signal receiver. Dust or dirt may cause defective contact.
ffDo not touch the lens surface with bare hands.
ffBefore attaching the projection lens, remove the lens cover attached to the projection lens.
ffThe procedure to remove/attach a projection lens cover differs for the ultra-short focus zoom lens (ET-DLE080). Refer to the user manual
provided with ET-DLE080 for details.
Removing the projection lens
Remove the projection lens in the following procedure.
1) Turn the projection lens cover
2) While pressing the lens release button, turn
the projection lens counterclockwise until it
stops.Remove the projection lens.
counterclockwise to remove.
Projection lens cover
(iii)
Projection lens
(i)
(ii)
(ii)
(i) Lens release button
Attention
ffStore the removed lens where it will be free from vibration and impact.
Attaching the projection lens
Attach the projection lens in the following procedure.
1) Remove the projection lens cover and insert
fully by aligning the projection lens guide with
the projector guide grooves.
2) Turn the projection lens clockwise until it
clicks.
Guide groove
Guide
Projection lens
ENGLISH - 35
Chapter 2 Getting Started — Removing/attaching the projection lens
3) Attach the projection lens cover aligning the
marking (groove *1) with the tip of the arrow
on the projector (*2), and secure the projection
lens cover by turning it until groove *1 aligns
with the *3 P marking.
(i)
Projection lens cover
*3
*2
(ii)
*1
Attention
ffTurn the projection lens counterclockwise to confirm that it does not come out.
36 - ENGLISH
Chapter 2 Getting Started — Connections
Connections
Before connecting to the projector
ffBefore connecting, carefully read the operating instructions for the external device to be connected.
ffTurn off the power of all devices before connecting cables.
ffAcquire any connection cable necessary to connect the external device to the system that is either not supplied with the device or not
available as an option.
ffVideo signals containing too much jitter may cause the images on the screen to randomly wobble or wafture. In this case, a time base
corrector (TBC) must be connected.
ffThe projector accepts video signals, S video signals, analog RGB signals (synchronous signals are TTL level), and digital signals.
ffSome computer models are not compatible with the projector.
ffUse a cable compensator when you connect devices to the projector using long cables. Otherwise the image may not display properly.
ffRefer to “List of compatible signals” (x page 125) for the types of video signals that can be used with the projector.
<S-VIDEO IN> terminal pin assignments and signal names
Pin No.
(1)
(2)
(3)
(4)
Outside view
(1)
(2)
(3)
(4)
Signal name
Ground (luminance signal)
Ground (color signal)
Luminance signal
Color signal
<RGB 2 IN> terminal pin assignments and signal names
Outside view
(11)
(15)
(6)
(10)
(1)
(5)
Pin No.
(1)
(2)
(3)
(12)
(13)
(14)
(15)
Signal name
R/PR
G/Y
B/PB
DDC data
SYNC/HD
VD
DDC clock
(4) and (9) are not used.
(5) - (8), (10), and (11) are GND terminals.
<DVI-D IN> terminal pin assignments and signal names
Outside view
(24)
(17)
(16)
(9)
(8)
(1)
Pin No.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
Signal name
T.M.D.S data 2T.M.D.S data 2+
T.M.D.S data 2/4 shield
―
―
DDC clock
DDC data
―
T.M.D.S data 1T.M.D.S data 1+
T.M.D.S data 1/3 shield
―
Pin No.
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
Signal name
―
+5 V
GND
Hot plug detection
T.M.D.S data 0T.M.D.S data 0+
T.M.D.S data 0/5 shield
―
―
T.M.D.S clock shield
T.M.D.S clock+
T.M.D.S clock-
Signal name
T.M.D.S clock shield
T.M.D.S clockCEC
—
SCL
SDA
DDC/CEC
GND
+5 V
Hot plug detection
<HDMI IN> terminal pin assignments and signal names
Outside view
Even-numbered pins (2) to (18)
(2)
(1)
(18)
(19)
Odd-numbered pins (1) to (19)
Pin No.
(1)
(2)
(3)
(4)
(5)
(6)
Signal name
T.M.D.S data 2+
T.M.D.S data 2 shield
T.M.D.S data 2T.M.D.S data 1+
T.M.D.S data 1 shield
T.M.D.S data 1-
Pin No.
(11)
(12)
(13)
(14)
(15)
(16)
(7)
T.M.D.S data 0+
(17)
(8)
(9)
(10)
T.M.D.S data 0 shield
T.M.D.S data 0T.M.D.S clock+
(18)
(19)
ENGLISH - 37
Chapter 2 Getting Started — Connections
Connecting example: AV equipment
DVD player with attached
HDMI terminal (HDCP)
VCR (with built-in TBC)
or
Blu-ray disc player
Attention
ffAlways use one of the following when connecting a VCR.
ggA VCR with built-in time base corrector (TBC)
ggA time base corrector (TBC) between the projector and the VCR
ffIf nonstandard burst signals are connected, the image may be distorted. In such case, connect the time base corrector (TBC) between the
projector and the VCR.
ffUse a commercial HDMI/DVI cable with a ferrite core.
Note
ffThe <DVI-D IN> terminal can be connected to HDMI- or DVI-D-compliant devices. However, images may not appear or may not be
displayed properly on some devices. (x page 70)
ffUse an HDMI cable that conforms to HDMI standards such as an HDMI High Speed cable. If a cable that does not meet HDMI standards is
used, video may be interrupted or may not be displayed.
ffThe <HDMI IN> terminal of the projector can be connected to an external device with a DVI-D terminal by using an HDMI/DVI conversion
cable, but some devices may not project the image properly or function properly.
ffWhen the DVI-D signal is input, EDID setting may be required depending on the connected device (x page 70).
ffThe projector does not support VIERA Link (HDMI).
Connecting example: Computers
Computer
Computer
Computer
Control
computer
Control
computer
Computer
Attention
ffWhen connecting the projector to a computer or an external device, use the power cord supplied with each device and commercially
available shielded cables.
ffUse a commercial DVI-D cable with a ferrite core.
Note
ffUse an HDMI cable that conforms to HDMI standards such as an HDMI High Speed cable. If a cable that does not meet HDMI standards is
used, video may be interrupted or may not be displayed.
38 - ENGLISH
Chapter 2 Getting Started — Connections
ffThe <HDMI IN> terminal of the projector can be connected to an external device with a DVI-D terminal by using an HDMI/DVI conversion
cable, but some devices may not project the image properly or function properly.
ffThe <DVI-D IN> terminal supports single link only.
ffFor signals that the projector can project, refer to “List of compatible signals” (x page 125).
ffIf you operate the projector using the computer with the resume feature (last memory), you may have to reset the resume feature to operate
the projector.
ffWhen the SYNC ON GREEN signal is input, do not enter sync signals to the <SYNC/HD> terminal or the <VD> terminal.
ffWhen the DVI-D signal is input, EDID setting may be required depending on the connected device (x page 70).
ENGLISH - 39
Chapter 3
Basic Operation
This chapter describes basic operations to start with.
40 - ENGLISH
Chapter 3 Basic Operation — Switching on/off the projector
Switching on/off the projector
Connecting the power cord
Make sure that the supplied power cord cover is securely fixed to the projector to prevent removal of the power cord.
Confirm that the <MAIN POWER> switch is on the <OFF> side before connecting the power cord.
For details of power cord handling, refer to “Read this first!” (x pages 2 to 8).
Attaching
1) Check the shapes of the <AC IN> terminal and
the power cord connector and insert the plug
securely in the correct direction.
2) Attach the power cord secure lock along with
the guide on the <AC IN> terminal.
3) Push in the tab of the power cord secure lock
until it clicks.
Tab
*XLGH
Removing
1) Confirm that the <MAIN POWER> switch of the
projector is at the <OFF> side, and unplug the
power plug from the outlet.
4) Remove the power cord connector from the
projector <AC IN> terminal.
2) Press down the tab of the power cord secure
lock to remove.
Tab
3) Remove the power cord secure lock from
the projector in the direction of the <AC IN>
terminal guide.
*XLGH
ENGLISH - 41
Chapter 3 Basic Operation — Switching on/off the projector
Power indicator
Displays the status of the power. Check the <ON (G)/STANDBY (R)> status of the power indicator before operating the projector.
Power indicator <ON（G）/STANDBY（R）>
Indicator status
Status
No illumination or flashing
The main power is switched off.
Red
Lit
The power is switched off. (Standby mode.)
Projection will start if the power on <b> button is pressed.
ffThe projector may not operate when the lamp indicators <LAMP1>/<LAMP2> or
temperature indicator <TEMP> is flashing. (x page 110)
Green
Lit
Projecting.
Orange
Lit
The projector is preparing to switch off the power.
The power is switched off after a while. (Changes to the standby mode.)
Note
ffWhen the power indicator <ON (G)/STANDBY (R)> lamp is lit in orange, the fan is turning and the projector is cooling.
ffThe projector consumes power even in standby mode (power indicator <ON (G)/STANDBY (R)> is lit in red).
Refer to “Power consumption” (x page 128) for the power consumption.
ffThe power indicator <ON (G)/STANDBY (R)> will flash in green if a remote control signal is received.
ffThe power indicator <ON (G)/STANDBY (R)> will flash slowly in green while the shutter is closed. (x page 47)
ffIf the power indicator <ON (G)/STANDBY (R)> is flashing in red, consult your dealer.
Switching on the projector
3)
3)
2)
1)
To use a projection lens that is an optional accessory, attach the lens before switching on the projector. (x page 35)
Remove the lens cover first.
1) Connect the power plug to an outlet.
ff(AC 220 V - 240 V 50 Hz/60 Hz)
2) Press the <ON> side of the <MAIN POWER>
3) Press the power on <b> button.
ffThe power indicator <ON (G)/STANDBY (R)> will light in green
and the image will soon be projected on the screen.
switch to turn on the power.
ffThe power indicator <ON (G)/STANDBY (R)> will light in red,
and the projector will enter the standby mode.
Note
ffIf the projector is switched on at about 0°C (32°F), a warm-up period of approximately five minutes may be necessary until a projection is
displayed.
The temperature indicator <TEMP> is lit during the warm-up period. When the warm-up is completed, the temperature indicator <TEMP>
turns off and the projection starts. Refer to “Managing the indicated problems” (x page 110) for the indicator status.
ffIf the operating environment temperature is low and warm-up takes more than 5 minutes, the projector will judge that a problem has
occurred and the power will automatically be set to stand-by. If this happens, increase the operating environment temperature to 0°C (32°F)
42 - ENGLISH
Chapter 3 Basic Operation — Switching on/off the projector
or higher, turn off the main power, and then turn on the power again.
ffIf [PROJECTOR SETUP] → [STANDBY MODE] (x page 78) is set to [ECO] on the menu, there may be a 10 second display lag when the
power is turned on compared to when the setting is [NORMAL].
ffIf the <MAIN POWER> switch was turned <OFF> during projection the last time that the direct power off function was used, and the <MAIN
POWER> switch is turned <ON> while the main power plug connected to the outlet, the power indicator <ON (G)/STANDBY (R)> will light in
green and the image will soon be projected on the screen.
Making adjustments and selections
It is recommended that images are projected continuously for at least 30 minutes before the focus is adjusted.
2)
1)
5) 7) 8) 9)
6)
3)
2)
5)
7) 9)
1) 8)
4)
3)
6)
1) Press the <FOCUS> button to roughly adjust
5) Press the <SHIFT> button to adjust the
2) Set the projection method using [PROJECTION
6) If the input signal is an RGB input signal, press
the focus of the image. (x page 45)
METHOD] (x page 75) and [COOLING
CONDITION] (x page 76) on the menu.
ffRefer to “Navigating through the menu” (x page 51) for the
operation of the menu.
3) Press the input selection (<RGB1>,
<RGB2>, <DVI-D>, <VIDEO>, <S-VIDEO>,
<HDMI>) buttons to select the input signal.
(x page 48)
4) Adjust the front, back and sideway tilt
position of the image. (x page 45)
the <AUTO SETUP> button. (x page 48)
7) Press the <ZOOM> button to adjust the size of
the image to match the screen. (x page 45)
8) Press the <FOCUS> button again to adjust the
focus.
9) Press the <ZOOM> button again to adjust the
zoom and the size of the image to match the
screen.
of the projector with the adjustable feet.
(x page 34)
Switching off the projector
3)
4)
1)
2)
1)
2)
1) Press the power standby <v> button.
ffThe [POWER OFF(STANDBY)] confirmation screen is
displayed.
2) Use qw to select [OK], and press the <ENTER>
button.
(Or press the power standby <v> button
again.)
ffProjection of the image will stop, and the power indicator <ON
(G)/STANDBY (R)> on the projector lights in orange. (The fan
keeps running.)
ENGLISH - 43
Chapter 3 Basic Operation — Switching on/off the projector
3) Wait until the power indicator <ON(G)/
STANDBY (R)> of the projector lights in red (and
the fan stops) for approximately 170 seconds.
4) Press the <OFF> side of the <MAIN POWER>
switch to turn off the power.
Note
ffDo not turn on the power and project images immediately after turning the projector off.
Turning on the power while the lamp is still hot may shorten the lamp life.
ffThe lamp indicators will not light on for about 75 seconds after the projector is switched off and the luminous lamp cooling has started even
if the power is switched. The indicators may not light when the power is switched on even after this time. In such a case, turn the power on
again after the power indicator <ON (G)/STANDBY (R)> lights in red.
ffThe projector consumes power when the main power of the projector is on, even if the power standby <v> button is pressed and
the power is switched off.
(when [STANDBY MODE] is set to [NORMAL])
When [STANDBY MODE] (x page 78) on the menu is set to [ECO], the power consumption during standby can be conserved.
Direct power off function
Even if the <MAIN POWER> switch is <OFF> during projection or immediately after the luminous lamp is turned off, the electricity stored in the
room will drive the fan and cool the luminous lamp. When mounting on the ceiling or other environment where the projector <MAIN POWER>
switch cannot easily be turned <OFF>, the power can be shut down directly from the power breaker. This method is safe in the event of a
blackout or if the power cord is removed directly after the projector is switched off.
Note
ffIf the power was shut down directly from the power circuit breaker during projection the last time that the projector was used, the power
indicator <ON (G)/STANDBY (R)> will light in green a while after the power circuit breaker is turned on and then transitions to image
projection.
ffIt may take more time than usual to project the next time that the power is turned on if direct power off is used to cool.
ffWhen packing for shipment or storage, ensure that the fan is stopped.
44 - ENGLISH
Chapter 3 Basic Operation — Projecting
Projecting
Check the projection lens attachment (x page 35), external device connection (x page 37) and power cord connection (x page 41),
and then switch on the power (x page 42) to start projecting. Select the video for projection, and adjust appearance of the projected image.
Selecting the input signal
Select an input signal.
1) Press the input selection (<RGB1>, <RGB2>,
<DVI-D>, <VIDEO>, <S-VIDEO>, <HDMI>)
buttons on the control panel or the remote
control.
ffThe image of the signal being input in the selected terminal is
projected.
Attention
ffImages may not be projected properly depending on the external device, or the blu-ray disc or DVD disc, to be played back.
Set [PICTURE] → [SYSTEM SELECTOR] (x page 59) on the menu.
ffConfirm the aspect ratio of the projection screen and the image, and switch to an optimum aspect ratio from [POSITION] → [ASPECT]
(x page 60) in the menu.
Adjusting the focus, zoom, and shift
If the projected image or the position is not correct though the positioning of the projector and the screen is correctly installed, adjust the focus,
zoom, and shift.
At the projector
1) Press the <LENS> button on the control panel.
2) Select each item and use asqw to adjust it.
ffThe setup screen will change each time you press the button.
rrAdjustable contents
[FOCUS]
Adjusts focus.
[ZOOM]
Adjusts zoom.
[SHIFT]
Adjusts shift.
Using the remote control
1) Press the lens (<FOCUS>, <ZOOM>, <SHIFT>)
buttons on the remote control.
2) Select each item and use asqw to adjust it.
rrAdjustable items
Operation
Item
Press the <FOCUS> button.
[FOCUS]
Adjusts focus.
Details
Press the <ZOOM> button.
[ZOOM]
Adjusts zoom.
Press the <SHIFT> button.
[SHIFT]
Adjusts shift.
Note
ffThe zoom adjustment menu is displayed even when a projection lens without zoom function is attached, but it will not operate.
ffUse the fixed-focus lens (ET-DLE055) with the lens position on the home position. (x page 46)
ffThe adjustment can be performed faster by pressing and holding asqw for at least three seconds.
ffIt is recommended that images are projected continuously for at least 30 minutes before the focus is adjusted.
ffOnly [FOCUS] is shown in yellow so that the displayed menu item can be recognized by color (even when the projector is not focused and
displayed characters are unreadable). (Factory default)
The [FOCUS] color depends on the [OSD DESIGN] (x page 72) settings in the menu.
ENGLISH - 45
Chapter 3 Basic Operation — Projecting
Moving the lens to the home position
Perform the following procedure to move the lens to the home position.
1) Press the <LENS> button on the control panel
or the <SHIFT> button on the remote control
for at least three seconds.
2) While the [HOME POSITION] menu is displayed
(for approximately five seconds), press the
<ENTER> button.
LENS
HOME POSITION
ENTER
MENU
EXECUTE
CANCEL
ff[PROGRESS] is displayed in the menu screen, and the lens
returns to the home position.
Attention
ffThe home position of the lens is the lens position when the lens is being replaced or when the projector is being stored, and it is not the
optical center of the screen.
Adjustment range by the lens position shift (optical shift)
Perform the lens position shift within the adjustment range.
The focus may change when the lens position is shifted out of the adjustment range. This is because the movement of the lens is restricted to
protect the optical parts. Projection position can be adjusted with the optical axis shift based on the standard projection position in the range
shown in the following figures.
Zoom lens
Lens type
Standard projection
position
0.1 H
Projection screen width H
0.1 H
0.6 V
0.5 V
0.1 H
Projection screen width H
Standard projection
position
0.1 H
Projection screen width H
*The numerical values in the diagrams above represent a case in which the projector is set on a desk/floor.
Note
ffWhen the fixed-focus lens (ET-DLE055) is attached, shift adjustment cannot be performed.
46 - ENGLISH
0.1 H
0.45 V
0.1 H
0.5 V
Projection screen width H
Standard projection
position
0.34 V
PT-DX810E
Projection screen height V
0.1 H
Projection screen height V
Standard projection
position
ET-DLE080
Projection screen height V
0.6 V
Projection screen height V
PT-DW740E
Standard zoom lens, ET-DLE150, ET-DLE250,
ET-DLE350, ET-DLE450
0.1 H
Chapter 3 Basic Operation — Remote control operation
Remote control operation
Using the shutter function
If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible to turn off the image
temporarily.
button
1) Press the <SHUTTER> button.
ffThe image disappears.
ffThis operation can be also performed using the <SHUTTER>
button on the control panel.
2) Press the <SHUTTER> button again.
ffThe image is displayed.
Note
ffThe power indicator <ON (G)/STANDBY (R)> will flash slowly in green while the shutter is closed.
Using the on-screen display function
Turn off the on-screen display function (no display) when you do not wish the viewers to see the on-screen display, such as the menu or the
input terminal name.
button
1) Press the <ON SCREEN> button.
ffThe on-screen display disappears.
2) Press the <ON SCREEN> button again.
ffThe on-screen display appears.
Note
ffIf you press the <MENU> button on the control panel for at least three seconds while the on-screen indication is off, the on-screen display is
turned on.
ENGLISH - 47
Chapter 3 Basic Operation — Remote control operation
Switching the input
The input for projection can be switched.
button
1) Press the input selection (<RGB1>, <RGB2>,
<DVI-D>, <VIDEO>, <S-VIDEO>, and <HDMI>)
buttons.
ffThis operation can be also performed by pressing the input
selection (<RGB1>, <RGB2>, <DVI-D>, <VIDEO>, <S-VIDEO>,
and <HDMI>) buttons on the control panel.
rrSwitching the input items
<RGB1>
Switches to RGB1 input.
<RGB2>
Switches to RGB2 input.
<DVI-D>
Switches to DVI-D input.
<VIDEO>
Switches to VIDEO input.
<S-VIDEO>
<HDMI>
Switches to S-VIDEO input.
Switches to HDMI input.
Using the status function
You can display the status of the projector.
button
1) Press the <STATUS> button.
ffThe [STATUS] screen is displayed.
67$786
,1387
6,*1$/1$0(
6,*1$/)5(48(1&<
352-(&7255817,0(
/$03
/$03
,17$.($,57(03
237,&602'8/(7(03
$5281'/$037(03
Note
ffThis can also be displayed from the [PROJECTOR SETUP] menu → [STATUS] (x page 81).
Using the automatic setup function
The automatic setup function can be used to automatically adjust the resolution, clock phase, and picture position when analog RGB signals
consisting of bitmap images such as computer signals are being input, or to automatically adjust the picture position when DVI-D/HDMI signals
are input. Supplying images with bright white borders at the edges and high-contrast black and white characters is recommended when the
system is in automatic adjustment mode.
Avoid supplying images that include halftones or gradation, such as photographs and computer graphics.
button
48 - ENGLISH
Chapter 3 Basic Operation — Remote control operation
1) Press the <AUTO SETUP> button.
ff[COMPLETE] is displayed when it has completed without any
problem.
ffThis operation can be also performed using the <AUTO
SETUP> button on the control panel.
Note
ffThe CLOCK PHASE may shift even if it has completed without any incident. In such cases, adjust with the [POSITION] menu → [CLOCK
PHASE] (x page 62).
ffIf an image with blurred edges or a dark image is input, [INCOMPLETE] may appear or adjustment may not be performed properly even if
[COMPLETE] appears. In this case, adjust the settings in [ADVANCED MENU] → [INPUT RESOLUTION] (x page 65), [POSITION] →
[CLOCK PHASE] (x page 62), [SHIFT](x page 60) in the menu.
ffAdjust special signals according to the [DISPLAY OPTION] → [AUTO SETUP] (x page 70) in the menu.
ffAutomatic adjustment may not work depending on the model of the computer.
ffAutomatic adjustment may not work for a synchronization signal of C-SY or SYNC ON GREEN.
ffImages may be disrupted for a few seconds during automatic adjustment, but it is not a malfunction.
ffAdjustment is required for each input signal.
ffAutomatic adjustment can be canceled by pressing the <MENU> button during the automatic adjustment operation.
ffIf automatic setup function is performed while moving images are being input, the adjustment may not be performed properly even for
an RGB signal for which automatic setup can be used. [INCOMPLETE] may appear, or adjustment may not be finished properly even if
[COMPLETE] appears.
Using the function button
[DISABLE], [SUB MEMORY], [SYSTEM SELECTOR], [SYSTEM DAYLIGHT VIEW], [FREEZE], or [SIDE BY SIDE] operations can be assigned
to the <FUNCTION> button on the remote control so that it can be used as an easy shortcut button.
button
1) Press the <FUNCTION> button.
Note
ff[SIDE BY SIDE] can be set only with PT-DW740E.
ffThe [PROJECTOR SETUP] → [FUNCTION BUTTON] (x page 82) in the menu performs function assignment.
Displaying the internal test pattern
The projector has nine types of internal test patterns to check the condition of the set. To display test patterns, perform the following steps.
button
1) Press the <TEST PATTERN> button.
2) Use qw to select a test pattern.
Note
ffYou can also use [TEST PATTERN] (x page 85) in the menu to perform settings.
ffSettings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before performing
various adjustments.
Changing the picture aspect ratio
You can toggle through aspect ratios to select the one that is appropriate for the input signal.
button
1) Press the <ASPECT> button.
ffThe setting will change each time you press the button.
Refer to “[ASPECT]” (x page 60) for details.
ENGLISH - 49
Chapter 4
Settings
This chapter describes the settings and adjustments you can make using the on-screen menu.
50 - ENGLISH
Chapter 4 Settings — Menu navigation
Menu navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.
Navigating through the menu
Operating procedure
button
1) Press the <MENU> button on the remote
control or the control panel.
ffThe [MAIN MENU] screen is displayed.
0$,10(18
3,&785(
326,7,21
$'9$1&('0(18
',63/$</$1*8$*(
3) Press the <ENTER> button.
ffThe sub-menu items of the selected main menu are displayed.
POSITION
SHIFT
ASPECT
DEFAULT
ZOOM
CLOCK PHASE
16
KEYSTONE
',63/$<237,21
352-(&7256(783
7(673$77(51
6,*1$//,67
6(&85,7<
1(7:25.
MENU SELECT
0(186(/(&7
(17(5
ENTER
SUB MENU
68%0(18
2) Press as to select an item from the main
menu.
ffThe selected item is highlighted in yellow.
0$,10(18
3,&785(
326,7,21
$'9$1&('0(18
',63/$</$1*8$*(
',63/$<237,21
4) Press as to select a sub-menu, and press
qw or the <ENTER> button to change or adjust
settings.
ffFor some items, press qw to display an individual adjustment
screen with a bar scale as shown in the following diagram.
&2175$67
$'-867
352-(&7256(783
7(673$77(51
6,*1$//,67
6(&85,7<
1(7:25.
0(186(/(&7
(17(5
68%0(18
Note
ffPressing the <MENU> button when the menu screen is displayed returns to the previous menu.
ffSome items may not be adjusted or used for certain signal formats to be input to the projector. The menu items that cannot be adjusted or
used are shown in black characters, and they cannot be selected.
ffSome items can be adjusted even if signals are not input.
ffIndividual adjustment screen is cleared automatically if no operation is performed for approximately five seconds.
ffFor menu items, refer to “Main menu” (x page 52) and “Sub-menu” (x pages 52 to 54).
ffThe cursor color depends on the [OSD DESIGN] (x page 72) settings on the menu. The selected item is displayed with the yellow cursor
by default.
To reset to the factory default
If the <DEFAULT> button on the remote control is pressed, the values adjusted in the menu items will be restored to the factory default
settings.
button
ENGLISH - 51
Chapter 4 Settings — Menu navigation
1) Press the <DEFAULT> button on the remote
control.
&2175$67
$'-867
Note
ffYou cannot reset all the settings to the factory default at once.
ffTo reset all the settings adjusted in the sub-menu item to the factory default at a time, perform initialization from the [PROJECTOR SETUP]
menu → [INITIALIZE] (x page 84).
ffSome menu items cannot be reset by pressing the <DEFAULT> button. Adjust each item manually.
ffThe triangular mark under the bar scale in the individual adjustment screen indicates the factory default setting. The position of the triangular
mark varies by the selected input signals.
Current adjustment value
Factory default setting
Main menu
The following 10 items are in the main menu.
When a main menu item is selected, the screen changes to a sub-menu selection screen.
Main menu item
Page
[PICTURE]
52
[POSITION]
53
[ADVANCED MENU]
53
[DISPLAY LANGUAGE]
53
[DISPLAY OPTION]
53
[PROJECTOR SETUP]
54
[TEST PATTERN]
54
[SIGNAL LIST]
54
[SECURITY]
54
[NETWORK]
54
Sub-menu
The sub-menu of the selected main menu item is displayed, and you can set and adjust items in the sub-menu.
[PICTURE]
Sub-menu item
Factory default
Page
[STANDARD]*
55
[CONTRAST]
[0]
55
[BRIGHTNESS]
[0]
55
[COLOR]
[0]
56
[TINT]
[0]
56
[DEFAULT]
56
[10]
57
[PICTURE MODE]
[COLOR TEMPERATURE]
[WHITE GAIN]
52 - ENGLISH
Chapter 4 Settings — Menu navigation
Sub-menu item
Factory default
Page
[OFF]*
57
[SHARPNESS]
[6]
58
[NOISE REDUCTION]
[1]
58
[SYSTEM DAYLIGHT VIEW]
[AI]
*
[ON]
[SYSTEM SELECTOR]
58
[YPBPR]
59
Factory default
Page
―
60
*
*Depends on the signal input.
Note
ffThe factory default settings may vary depending on the picture mode.
[POSITION]
Sub-menu item
[SHIFT]
[ASPECT]
[DEFAULT]
60
―
61
[16]
62
―
63
Factory default
Page
[AUTO]*
64
―
64
―
65
*
[ZOOM]
[CLOCK PHASE]
[KEYSTONE]
*Depends on the signal input.
[ADVANCED MENU]
Sub-menu item
[DIGITAL CINEMA REALITY]
[BLANKING]
[INPUT RESOLUTION]
[CLAMP POSITION]
[24]*
65
[EDGE BLENDING]
[OFF]
65
―
66
Factory default
Page
[COLOR MATCHING]
[OFF]
68
[COLOR CORRECTION]
[OFF]
69
[CONTRAST MODE]
[NORMAL]
69
[SCREEN SETTING]
―
69
[RASTER POSITION]
*Depends on the signal input.
[DISPLAY LANGUAGE]
Details (x page 67)
[DISPLAY OPTION]
Sub-menu item
[AUTO SIGNAL]
[OFF]
70
[AUTO SETUP]
―
70
[RGB IN]
―
70
[DVI-D IN]
―
70
[HDMI IN]
―
71
[ON-SCREEN DISPLAY]
[BACK COLOR]
[STARTUP LOGO]
―
71
[BLUE]
72
[DEFAULT LOGO]
72
[SHUTTER SETTING]
―
73
[FREEZE]
―
73
[SIDE BY SIDE]
―
73
[CUT OFF]
―
74
*
*Only for PT-DW740E.
ENGLISH - 53
Chapter 4 Settings — Menu navigation
[PROJECTOR SETUP]
Sub-menu item
[PROJECTOR ID]
Factory default
Page
[ALL]
75
[PROJECTION METHOD]
[FRONT/FLOOR]
75
[COOLING CONDITION]
[FLOOR SETTING]
76
[HIGH ALTITUDE MODE]
[OFF]
76
[DUAL]
76
[LAMP RELAY]
[OFF]
77
[LAMP POWER]
[NORMAL]
77
[STANDBY MODE]
[NORMAL]
78
[OFF]
78
[LAST USED]
79
―
80
[DEFAULT]
81
[LAMP SELECT]
[SCHEDULE]
[STARTUP INPUT SELECT]
[RS-232C]
[REMOTE2 MODE]
[STATUS]
―
81
[DISABLE]
82
[FUNCTION BUTTON]
―
82
[DATE AND TIME]
―
83
[SAVE ALL USER DATA]
―
83
[LOAD ALL USER DATA]
―
84
[INITIALIZE]
―
84
[SERVICE PASSWORD]
―
84
Factory default
Page
[OFF]
89
―
89
[OFF]
89
―
90
[NO SIGNAL SHUT-OFF]
[TEST PATTERN]
Details (x page 85)
[SIGNAL LIST]
Details (x page 86)
[SECURITY]
Sub-menu item
[SECURITY PASSWORD]
[SECURITY PASSWORD CHANGE]
[DISPLAY SETTING]
[TEXT CHANGE]
[MENU LOCK]
[OFF]
90
[MENU LOCK PASSWORD]
―
90
[CONTROL DEVICE SETUP]
―
90
Factory default
Page
[NETWORK SETUP]
―
92
[NETWORK CONTROL]
―
92
[NETWORK STATUS]
―
93
[NETWORK]
Sub-menu item
Note
ffSome items may not be adjusted or used for certain signal formats to be input to the projector.
The menu items that cannot be adjusted or used are shown in black characters, and they cannot be selected.
ffSub-menu items and factory default settings differ depending on the selected input terminal.
54 - ENGLISH
Chapter 4 Settings — [PICTURE] menu
[PICTURE] menu
Select [PICTURE] from the main menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” (x page 51) for the operation of the menu screen.
ffAfter selecting the item, press asqw to adjust.
[PICTURE MODE]
You can switch to the desired picture mode suitable for the image source and the environment in which the projector is used.
1) Press as to select [PICTURE MODE].
3) Press qw to switch [PICTURE MODE].
ffThe setting will change among [STANDARD], [CINEMA],
[NATURAL], [REC709], [DICOM SIM.], [DYNAMIC] and
[GRAPHIC] each time you press the button.
2) Press qw or the <ENTER> button.
ffThe [PICTURE MODE] individual adjustment screen is
displayed.
rr[PICTURE MODE]
[STANDARD]
[CINEMA]
[NATURAL]
[REC709]*
[DICOM SIM.]*
The picture becomes suitable for moving images in general.
The picture becomes suitable for movie sources.
The picture is sRGB compliant.
The picture is REC709 compliant.
The picture becomes similar to that of DICOM Part14 Grayscale Standard.
[DYNAMIC]
The light output is maximized for use in bright areas.
[GRAPHIC]
The picture becomes suitable for input to the personal computer.
*Use the factory default for the settings other than [PICTURE MODE].
Note
ffThe factory default picture mode is [GRAPHIC] for still image input signals and [STANDARD] for movie based input signals.
ffDICOM is an abbreviation for “Digital Imaging and Communication in Medicine” and is a standard for medical imaging devices. Although the
DICOM name is used, the projector is not a medical device, and should not be used for purposes such as diagnosis of display images.
[CONTRAST]
You can adjust the contrast of the colors.
1) Press as to select [CONTRAST].
2) Press qw or the <ENTER> button.
ffThe [CONTRAST] individual adjustment screen is displayed.
3) Press qw to adjust the level.
rrOperations and adjustment range
Operation
Adjustment
Press w.
Brightens the screen and makes the color of image deeper.
Press q.
Darkens the screen and makes the color of image lighter.
Range
-31 - +31
Attention
ffAdjust [BRIGHTNESS] first when you need to adjust the black level.
[BRIGHTNESS]
You can adjust the dark (black) part of the projected image.
1) Press as to select [BRIGHTNESS].
2) Press qw or the <ENTER> button.
ffThe [BRIGHTNESS] individual adjustment screen is displayed.
ENGLISH - 55
Chapter 4 Settings — [PICTURE] menu
3) Press qw to adjust the level.
rrOperations and adjustment range
Operation
Adjustment
Press w.
Increases the brightness of the dark (black) parts of the
screen.
Press q.
Reduces the brightness of the dark (black) parts of the screen.
Range
-31 - +31
[COLOR]
You can adjust the color saturation of the projected image.
1) Press as to select [COLOR].
2) Press qw or the <ENTER> button.
ffThe [COLOR] individual adjustment screen is displayed.
3) Press qw to adjust the level.
rrOperations and adjustment range
Operation
Adjustment
Press w.
Deepens colors.
Press q.
Weakens colors.
Range
-31 - +31
[TINT]
You can adjust the skin tone in the projected image.
1) Press as to select [TINT].
2) Press qw or the <ENTER> button.
ffThe [TINT] individual adjustment screen is displayed.
3) Press qw to adjust the level.
rrOperations and adjustment range
Operation
Adjustment
Press w.
Adjusts skin tone toward greenish color.
Press q.
Adjusts skin tone toward reddish purple.
Range
-31 - +31
[COLOR TEMPERATURE]
You can switch the color temperature if the white areas of the projected image are bluish or reddish.
To adjust with color temperature
1) Press as to select [COLOR TEMPERATURE].
2) Press qw or the <ENTER> button.
ffThe [COLOR TEMPERATURE] individual adjustment screen is
displayed.
3) Press qw to switch [COLOR TEMPERATURE].
ffThe setting will change among [DEFAULT], [USER], [MIDDLE]
and [HIGH] each time you press the button.
ffWhen [COLOR MATCHING] (x page 68) adjustment is set to
other than [OFF], [COLOR TEMPERATURE] is fixed to [USER].
rr[COLOR TEMPERATURE]
[DEFAULT]
[USER]
[MIDDLE]
[HIGH]
Factory default setting.
Adjusts white balance as desired. Refer to “To adjust desired white balance” for details.
Select so that images become natural.
To adjust desired white balance
1) Press as to select [COLOR TEMPERATURE].
3) Press qw to select [USER].
2) Press qw or the <ENTER> button.
4) Press the <ENTER> button.
ffThe [COLOR TEMPERATURE] individual adjustment screen is
displayed.
56 - ENGLISH
ffThe [COLOR TEMPERATURE] screen is displayed.
5) Press as to select [WHITE BALANCE].
Chapter 4 Settings — [PICTURE] menu
6) Press the <ENTER> button.
8) Press the <ENTER> button.
ffThe [WHITE BALANCE] screen is displayed.
ffThe [WHITE BALANCE HIGH] screen or the [WHITE
BALANCE LOW] screen is displayed.
7) Press as to select [WHITE BALANCE HIGH]
9) Press as to select [RED], [GREEN], or [BLUE].
or [WHITE BALANCE LOW].
10)Press qw to adjust the level.
rrAdjustment details
Item
Operation
[RED]
[GREEN]
[BLUE]
Press w.
Adjustment
Range
Deepens red.
Press q.
Weakens red.
Press w.
Deepens green.
Press q.
Weakens green.
Press w.
Deepens blue.
Press q.
Weakens blue.
[WHITE BALANCE HIGH]: 0 - +255 (factory default is
+255)
[WHITE BALANCE LOW]: 0 - +63 (factory default is +32)
Note
ffAdjust [COLOR TEMPERATURE] correctly. All colors will not be displayed properly unless adequate adjustment is made. If the adjustment
does not look suitable, you can press the <DEFAULT> button on the remote control to return the setting for the selected item only to the
factory default setting.
ffThe setting of [COLOR TEMPERATURE] is not reflected in internal test patterns (x page 85). Make sure to set [COLOR TEMPERATURE]
while projecting input signal.
To change the [USER] name
Select the language to show on the screen. (x page 67)
1) Press as to select [COLOR TEMPERATURE].
6) Press the <ENTER> button.
ffThe [COLOR TEMPERATURE NAME CHANGE] screen is
displayed.
2) Press qw or the <ENTER> button.
ffThe [COLOR TEMPERATURE] individual adjustment screen is
displayed.
7) Press asqw to select the text, and press the
<ENTER> button to enter the text.
3) Press qw to select [USER].
8) Press asqw to select [OK], and press the
4) Press the <ENTER> button.
<ENTER> button.
ffThe [COLOR TEMPERATURE] screen is displayed.
ffThe name set to color temperature is changed.
5) Press as to select [COLOR TEMPERATURE
NAME CHANGE].
Note
ffWhen a name is changed, display of [USER] on the menu is also changed.
[WHITE GAIN]
You can adjust the brightness of white areas of the image.
1) Press as to select [WHITE GAIN].
2) Press qw or the <ENTER> button.
ffThe [WHITE GAIN] individual adjustment screen is displayed.
3) Press qw to adjust the level.
rrOperations and adjustment range
Operation
Adjustment
Press w.
Increases the luminance of white.
Press q.
Image becomes more natural.
Range
0 - +10
[SYSTEM DAYLIGHT VIEW]
You can correct the image to the optimal vividness even if it is projected under a bright light.
1) Press as to select [SYSTEM DAYLIGHT
VIEW].
ENGLISH - 57
Chapter 4 Settings — [PICTURE] menu
2) Press qw or the <ENTER> button.
3) Press qw to switch [SYSTEM DAYLIGHT
VIEW].
ffThe [SYSTEM DAYLIGHT VIEW] individual adjustment screen
is displayed.
ffThe setting will change among [OFF], [1], [2] and [3] each time
you press the button.
rr[SYSTEM DAYLIGHT VIEW]
[OFF]
No correction.
[1]
Corrects the image to weaken vividness.
[2]
Corrects the image to medium vividness.
[3]
Corrects the image to high vividness.
[SHARPNESS]
You can adjust the sharpness of the projected image.
1) Press as to select [SHARPNESS].
2) Press qw or the <ENTER> button.
ffThe [SHARPNESS] individual adjustment screen is displayed.
3) Press qw to adjust the level.
rrOperations and adjustment range
Operation
Adjustment
Press w.
Contours become sharper.
Press q.
Contours become softer.
Range
0 - +15
Note
ffIf you press w while the adjustment value is [+15], the value will become [0]. If you press q while the adjustment value is [0], the value will
become [+15].
[NOISE REDUCTION]
You can reduce noises when the input image is degraded and noise is occurring in the image signal.
1) Press as to select [NOISE REDUCTION].
2) Press qw or the <ENTER> button.
3) Press qw to switch [NOISE REDUCTION].
ffThe setting will change among [1], [2], [3] and [OFF] each time
you press the button.
ffThe [NOISE REDUCTION] individual adjustment screen is
displayed.
rr[NOISE REDUCTION]
[1]
Corrects the noise to low level.
[2]
Corrects the noise to medium level.
[3]
Corrects the noise to high level.
[OFF]
No correction.
Attention
ffWhen this is set for an input signal with less noise, the image may look different from what it originally was. In such case, set it to [OFF].
[AI]
You can perform gradation control appropriate for an image to project it with optimal contrast.
1) Press as to select [AI].
2) Press qw or the <ENTER> button.
ffThe [AI] individual adjustment screen is displayed.
rr[AI]
[ON]
Enables AI correction.
[OFF]
Disables AI correction.
58 - ENGLISH
3) Press qw to switch [AI].
ffThe setting will change between [ON] and [OFF] each time you
press the button.
Chapter 4 Settings — [PICTURE] menu
[SYSTEM SELECTOR]
The projector will automatically detect the input signal, but you can set the system method manually when an unstable signal is input. Set the
system method matching the input signal.
1) Press as to select [SYSTEM SELECTOR].
3) Press as to select a system format.
2) Press the <ENTER> button.
4) Press the <ENTER> button.
rrAvailable system formats
Terminals
<VIDEO IN> terminal,
<S-VIDEO IN> terminal
<RGB 1 IN> terminal,
<RGB 2 IN> terminal
<DVI-D IN> terminal
<HDMI IN> terminal
System format
Select [AUTO], [NTSC], [NTSC4.43], [PAL], [PAL-M], [PAL-N], [SECAM], or [PAL60].
Set it to [AUTO] normally. (Setting [AUTO] will automatically select [NTSC], [NTSC4.43], [PAL], [PAL-M],
[PAL-N], [SECAM], or [PAL60].)
Switch the setting to the signal method for the TV used. NTSC signal method is used in Japan.
480i, 576i, or 576p signal
VGA60 or 480p signal
Select [RGB] or [YCBCR].
Select [VGA60], [480p], or [480pRGB].
Other movie based signals
Select [RGB] or [YPBPR].
480p or 576p signal
Select [RGB] or [YCBCR].
Other movie based signals
Select [RGB] or [YPBPR].
480p or 576p signal
Select [AUTO], [RGB], or [YCBCR].
Other movie based signals
Select [AUTO], [RGB], or [YPBPR].
Note
ffRefer to “List of compatible signals” (x page 125) for compatible signals.
ffThis may not function properly for some external devices that are connected.
ENGLISH - 59
Chapter 4 Settings — [POSITION] menu
[POSITION] menu
Select [POSITION] from the main menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” (x page 51) for the operation of the menu screen.
ffAfter selecting the item, press asqw to adjust.
[SHIFT]
You can move the image position vertically or horizontally if the image position projected on the screen is shifted even when the relative
position of the projector and the screen is installed correctly.
1) Press as to select [SHIFT].
2) Press the <ENTER> button.
ffThe [SHIFT] screen is displayed.
3) Press asqw to adjust the position.
rrAdjustment details
Orientation
Operation
Adjustment
Press a.
The picture position moves up.
Press s.
The picture position moves down.
Press w.
The picture position moves to the right.
Press q.
The picture position moves to the left.
Vertical (up and down)
adjustment
Horizontal (right and left)
adjustment
[ASPECT]
You can switch the aspect ratio of the image.
The aspect ratio is switched within the screen range selected in [SCREEN SETTING]. Set [SCREEN SETTING] first. (x page 69)
1) Press as to select [ASPECT].
2) Press qw or the <ENTER> button.
ffThe [ASPECT] individual adjustment screen is displayed.
3) Press qw to switch [ASPECT].
ffThe setting will change among [DEFAULT]*1/[VID AUTO]*2/
[AUTO]*3, [S1 AUTO]*4, [VID AUTO(PRI.)]*5, [THROUGH], [16:9],
[4:3], [H FIT], [V FIT], and [HV FIT] each time you press the
button.
*1
*2
*3
*4
*5
60 - ENGLISH
Not during VIDEO/S-VIDEO (NTSC)/RGB (480i, 480p) signal input
Only during VIDEO/S-VIDEO (NTSC) signal input
Only during RGB (480i, 480p) signal input
Only during S-VIDEO (NTSC) signal input
This is the factory default setting during S-VIDEO (NTSC) input.
The settings will rotate from [VID AUTO(PRI.)].
Chapter 4 Settings — [POSITION] menu
rr[ASPECT]
[DEFAULT]
Pictures are displayed without changing the aspect ratio of the input signals.
[VID AUTO]
The projector identifies the video ID (VID) embedded in the image signals and displays the image by
automatically switching the screen sizes between 4:3 and 16:9. This function is effective for VIDEO/S-VIDEO
(NTSC) signals.
[S1 AUTO]
The projector identifies the S1 signal, and displays the image by automatically switching the screen sizes
between 4:3 and 16:9. This function is effective for S-VIDEO (NTSC) signals.
[VID AUTO(PRI.)]
[AUTO]
[THROUGH]
The projector identifies the video ID (VID) embedded in image signals and S1 signals, and displays the
image by automatically switching the screen sizes between 4:3 and 16:9 in accordance with VID if it detects
VID, or S1 signal if it does not detect VID. This function is effective for S-VIDEO (NTSC) signals.
The projector identifies the video ID (VID) embedded in the image signals and displays the image by
automatically switching the screen sizes between 4:3 and 16:9. This function is effective for 480i/480p
signals.
Pictures are displayed without changing the resolution of the input signals.
[16:9]
When standard signals*1 are input, the pictures are displayed with the aspect ratio converted to 16:9. When
wide-screen signals*2 are input, the pictures are displayed without changing the aspect ratio.
[4:3]
When standard signals*1 are input, the pictures are displayed without changing the aspect ratio. When
wide-screen signals*2 are input, if [4:3] is selected with [SCREEN FORMAT], the pictures are displayed with
the aspect ratio converted to 4:3. When [SCREEN FORMAT] is other than [4:3], the picture size is reduced
without changing the aspect ratio so that the pictures will fit in the 4:3 screen.
[H FIT]
The pictures are displayed using the entire width of the screen range selected with [SCREEN FORMAT].
When signals have the aspect ratio vertically longer than the aspect ratio of the screen selected with
[SCREEN FORMAT], the pictures are displayed with the top and bottom parts cut off.
[V FIT]
The pictures are displayed using the entire height of the screen range selected with [SCREEN FORMAT].
When signals have the aspect ratio horizontally longer than the aspect ratio of the screen selected with
[SCREEN FORMAT], the pictures are displayed with the right and left parts cut off.
[HV FIT]
The pictures are displayed in the entire screen range selected with [SCREEN FORMAT]. When the aspect
ratio of the input signals differs from that of the screen range, the pictures are displayed with the aspect
ratio converted to that of the screen selected with [SCREEN FORMAT].
*1 Standard signals are input signals with an aspect ratio of 4:3 or 5:4.
*2 Wide-screen signals are input signals with an aspect ratio of 16:10, 16:9, 15:9 or 15:10.
Note
ffSome size modes are not available for certain types of input signals. [DEFAULT] cannot be selected for NTSC signals.
ffIf an aspect ratio which is different from the aspect ratio for the input signals is selected, the pictures will appear differently from the originals.
Be careful of this when selecting the aspect ratio.
ffIf using this projector in places such as cafes or hotels to display programs for a commercial purpose or for public presentation, note that
adjusting the aspect ratio or using the zoom function to change the screen pictures may be an infringement of the rights of the original
copyright owner for that program under copyright protection laws. Take care when using a function of the projector such as the aspect ratio
adjustment and zoom function.
ffIf conventional (normal) 4:3 pictures which are not wide-screen pictures are displayed on a wide screen, the edges of the pictures may not
be visible or they may become distorted. Such pictures should be viewed with an aspect ratio of 4:3 in the original format intended by the
creator of the pictures.
[ZOOM]
You can adjust the size of the projected image.
When [ASPECT] is set to other than [DEFAULT] or [THROUGH]
1) Press as to select [ZOOM].
4) Press qw to switch [INTERLOCKED].
2) Press the <ENTER> button.
5) Press as to select [VERTICAL] or
[HORIZONTAL].
ffThe [ZOOM] screen is displayed.
3) Press as to select [INTERLOCKED].
ffSelect [BOTH] when [ON] is selected.
6) Press qw to adjust.
rr[INTERLOCKED]
[OFF]
[ON]
[VERTICAL]
[HORIZONTAL]
[BOTH]
Set the [VERTICAL] and [HORIZONTAL] zoom ratio.
Use [BOTH] to set zoom ratio. Horizontal and vertical can be expanded
by units of 1.0 time.
ENGLISH - 61
Chapter 4 Settings — [POSITION] menu
Note
ffWhen [ASPECT] is set to [THROUGH], [ZOOM] is not displayed.
When [ASPECT] is set to [DEFAULT]
1) Press as to select [ZOOM].
5) Press as to select [INTERLOCKED].
2) Press the <ENTER> button.
6) Press qw to switch [INTERLOCKED].
ffThe [ZOOM] screen is displayed.
7) Press as to select [VERTICAL] or
3) Press as to select [MODE].
[HORIZONTAL].
ffSelect [BOTH] when [ON] is selected.
4) Press qw to switch [MODE].
8) Press qw to adjust.
rr[MODE]
[INTERNAL]
[FULL]
Enlarges the size within the aspect range set with [SCREEN FORMAT].
Enlarges the size to the entire display area set with [SCREEN FORMAT].
rr[INTERLOCKED]
[OFF]
[ON]
[VERTICAL]
[HORIZONTAL]
[BOTH]
Set the [VERTICAL] and [HORIZONTAL] zoom ratio.
Use [BOTH] to set zoom ratio. Horizontal and vertical can be expanded
by units of 1.0 time.
Note
ffWhen [ASPECT] is set to other than [DEFAULT], [MODE] is not displayed.
[CLOCK PHASE]
You can adjust to achieve an optimal image when there is a flickering image or smeared outlines.
1) Press as to select [CLOCK PHASE].
2) Press qw or the <ENTER> button.
3) Press qw to adjust.
ffAdjustment value will change between 0 and +31. Adjust so that
the amount of interference is at a minimum.
ffThe [CLOCK PHASE] individual adjustment screen is
displayed.
Note
ffOptimal value may not be achieved if the output from the input computer is unstable.
ffOptimal value may not be achieved when there is a shift in the total dot numbers.
ff[CLOCK PHASE] can be adjusted only when a signal is input to the <RGB 1 IN> terminal or the <RGB 2 IN> terminal.
ff[CLOCK PHASE] cannot be adjusted when a digital signal is input.
ffIf you press w while the adjustment value is [+31], the value will become [0]. If you press q while the adjustment value is [0], the value will
become [+31].
62 - ENGLISH
Chapter 4 Settings — [POSITION] menu
[KEYSTONE]
You can correct the trapezoidal distortion that occurs when the projector is installed tilted or when the screen is tilted.
1) Press as to select [KEYSTONE].
3) Press as to select the item to adjust.
2) Press the <ENTER> button.
4) Press qw to adjust.
ffThe [KEYSTONE] screen is displayed.
rrAdjustment details
[KEYSTONE]
[SUB KEYSTONE]
[LINEARITY]
Note
ffThe menu or logo may run off the screen when various adjustments are performed with [KEYSTONE].
ffVarious adjustments with [KEYSTONE] are possible to correct up to ±40° for the tilt in vertical direction. However, the picture quality will
degrade and it will get harder to focus with more correction. Install the projector so the correction will be as small as possible. (±30° when
using fixed-focus lens (ET-DLE055), or super short focus zoom lens (ET-DLE080).)
ffImage size will also change when [KEYSTONE] is used to perform adjustments.
ffTrapezoidal distortion may occur depending on the lens shift position.
ffAspect ratio of the image size may shift depending on the correction or lens zoom value.
ENGLISH - 63
Chapter 4 Settings — [ADVANCED MENU] menu
[ADVANCED MENU] menu
Select [ADVANCED MENU] from the main menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” (x page 51) for the operation of the menu screen.
ffAfter selecting the item, press asqw to adjust.
[DIGITAL CINEMA REALITY]
You can increase the vertical resolution and enhance the picture quality by performing the cinema processing when the PAL (or the SECAM)
576i signal, the NTSC 480i, 1080/50i, and 1080/60i signals are input.
1) Press as to select [DIGITAL CINEMA
REALITY].
2) Press qw to switch [DIGITAL CINEMA
REALITY].
ffThe setting will change among [AUTO], [OFF] and [25p
FIXED]*1/[30p FIXED]*2 each time you press the button.
*1 Only during 576i,1080/50i signal input
*2 Only during 480i,1080/60i signal input
rr[DIGITAL CINEMA REALITY]
[AUTO]
Performs automatic detection and cinema processing. (Factory default)
[OFF]
Unforced cinema processing.
[25p FIXED]
Forced cinema processing (2:2 pulldown) is performed when a 576i or 1080/50i signal is input.
[30p FIXED]
Forced cinema processing (2:2 pulldown) is performed when a 480i or 1080/60i signal is input.
Note
ffWhen a signal other than a 2:2 pulled-down signal is set to [25p FIXED] or [30p FIXED] in [DIGITAL CINEMA REALITY], picture quality
deteriorates. (Vertical resolution will degrade.)
[BLANKING]
The blanking width is adjusted when there are noise at the edge of the screen or the image is slightly running out from the screen when an
image from the VCR or other devices are projected.
1) Press as to select [BLANKING].
3) Press as to select an adjustment item.
2) Press the <ENTER> button.
4) Press qw to adjust the blanking.
ffThe [BLANKING] adjustment screen is displayed.
rrAdjustment details
Blanking correction
Item
Top of the screen
Bottom of the screen
Operation
Adjustment
Press q.
The blanking zone
moves upward.
Press w.
The blanking zone
moves downward.
Range
[UPPER]
Press q.
The blanking zone
moves upward.
Press w.
The blanking zone
moves downward.
[LOWER]
64 - ENGLISH
PT-DW740E: 0 to 399
PT-DX810E: 0 to 383
Chapter 4 Settings — [ADVANCED MENU] menu
Blanking correction
Left side of the screen
Right side of the
screen
Item
Operation
Adjustment
Press w.
The blanking zone
moves to the right.
Press q.
The blanking zone
moves to the left.
Range
[LEFT]
Press w.
The blanking zone
moves to the right.
Press q.
The blanking zone
moves to the left.
PT-DW740E: 0 to 639
PT-DX810E: 0 to 511
[RIGHT]
[INPUT RESOLUTION]
You can adjust to achieve an optimal image when there is a flickering image or smeared outlines.
1) Press as to select [INPUT RESOLUTION].
2) Press the <ENTER> button.
ffThe [INPUT RESOLUTION] screen is displayed.
3) Press as to select [TOTAL DOTS], [DISPLAY
DOTS], [TOTAL LINES], or [DISPLAY LINES],
then press qw to adjust it.
ffValues corresponding to the input signal are displayed
automatically for each item. Change the displayed values and
adjust to the optimal image viewing the screen when there is a
vertical banding or missing in the screen.
Note
ffPreviously mentioned vertical banding will not occur with all white signal input.
ffThe image may be disrupted while performing the adjustment, but it is not a malfunction.
ff[INPUT RESOLUTION] can be adjusted only when an RGB signal is input to the <RGB 1 IN> terminal or the <RGB 2 IN> terminal.
ffCertain signals may not be adjustable.
[CLAMP POSITION]
You can adjust the optimal point when the black part of the image is blunt or it has turned green.
1) Press as to select [CLAMP POSITION].
2) Press qw to adjust.
rrAdjustment details
Status
Rough guide for optimal value
The black part is blunt.
The point where bluntness of the black part improves the most
is the optimal value.
The black part is green.
The point where the green part becomes black, and the
bluntness improves is the optimal value.
Range
1 - 255
Note
ff[CLAMP POSITION] can be adjusted only when a signal is input to the <RGB 1 IN> terminal or the <RGB 2 IN> terminal.
ffCertain signals may not be adjustable.
[EDGE BLENDING]
The edge blending function allows multiple projector images to be seamlessly overlapped by using the inclination of the brightness at the
overlapped area.
1) Press as to select [EDGE BLENDING].
2) Press qw to switch [EDGE BLENDING].
ffThe setting will change between [ON] and [OFF] each time you
press the button.
ffTo adjust edge blending, proceed to Step 3).
3) Press the <ENTER> button when [ON] is
selected.
ffThe [EDGE BLENDING] screen is displayed.
4) Press as to specify the location to be
corrected.
ffWhen joining at top: Set [UPPER] to [ON].
ffWhen joining at bottom: Set [LOWER] to [ON].
ffWhen joining at left: Set [LEFT] to [ON].
ffWhen joining at right: Set [RIGHT] to [ON].
5) Press qw to switch between [ON] and [OFF].
ffTo adjust edge blending without displaying the adjustment
marker, proceed to Step 8).
6) Press as to select [MARKER].
ENGLISH - 65
Chapter 4 Settings — [ADVANCED MENU] menu
7) Press qw to switch [ON].
ffA marker for image position adjustment is displayed.
8) Press as to select [START] or [WIDTH],
then press qw to adjust starting point and
correction width.
ffThe green line is the starting point of edge blending adjusted
with [START]. The red line is the ending point of edge blending
adjusted with [WIDTH]. The position where the red and green
lines overlap for the sets to join will be the optimal point.
Make sure to set the correction width for the sets to join as the
same value. Optimal joining is not possible with the sets with
different correction widths.
The optimal point is the point at which these lines overlap.
14)Press the <ENTER> button.
ffThe [BRIGHT INSIDE] individual adjustment screen is
displayed.
ffIf [INTERLOCKED] is set to [OFF], [RED], [GREEN], and [BLUE]
can be adjusted individually.
15)Press as to select an item, then press qw to
adjust it.
ffOnce the adjustment is completed, press the <MENU> button to
return to the [BRIGHT ADJUST] screen.
16)Press as to select [UPPER], [LOWER], [LEFT],
or [RIGHT] from [OUTSIDE AREA].
17)Press qw to set the region (width) of the
[BRIGHT INSIDE] adjustment.
18)Press as to select [BRIGHT OUTSIDE].
19)Press the <ENTER> button.
ffThe [BRIGHT OUTSIDE] individual adjustment screen is
displayed.
ffIf [INTERLOCKED] is set to [OFF], [RED], [GREEN], and [BLUE]
can be adjusted individually.
Green line
Red line
9) Press as to select [GAMMA].
20)Press as to select an item, then press qw to
adjust it.
[OUTSIDE AREA] (Right)
Projection range Edge blending [WIDTH] (Right)
10)Press qw to switch [GAMMA].
ffThe setting will change among [2.2], [1.8], and [2.0] each time
you press the button.
11)Press as to select [BRIGHT ADJUST].
12)Press the <ENTER> button.
ffThe [BRIGHT ADJUST] screen is displayed.
13)Press as to select [BRIGHT INSIDE].
[MARKER] (Red)
Edge blending [START] (Right)
([MARKER] (Green))
[BRIGHT OUTSIDE]
[BRIGHT INSIDE]
rr[EDGE BLENDING]
[OFF]
Sets the edge blending function to off.
[ON]
Use the setting value of the internal distortion of the set for the inclination of the edge blending area.
rr[GAMMA]
[2.2]
[1.8]
[2.0]
The screen becomes darker as the value increases. Set this item according to the condition of the joined
part.
Note
ff[BRIGHT ADJUST] is a function that makes the increased brightness in black level of the overlapping image area difficult to notice when
[EDGE BLENDING] is used to configure multiple screens. The optimal point of the correction is set by adjusting [BRIGHT INSIDE] so the
black level of the overlapping image area will be the same level as the non-overlapping area. If the bordering part of the part where the
image is overlapping and the non-overlapping part gets brighter after adjusting [BRIGHT INSIDE], adjust the width of the top, bottom, left, or
right. Adjust [BRIGHT OUTSIDE] when the width adjustment makes only the border area darker.
ffThe joining part may look discontinuous depending on the position you are looking from when a screen with high gain or rear screen is used.
[RASTER POSITION]
This will allow the position of the image to move within the display area arbitrarily when the input image is not using the whole display area.
1) Press as to select [RASTER POSITION].
2) Press the <ENTER> button.
ffThe [RASTER POSITION] screen is displayed.
66 - ENGLISH
3) Press asqw to adjust the position.
Chapter 4 Settings — [DISPLAY LANGUAGE] menu
[DISPLAY LANGUAGE] menu
Select [DISPLAY LANGUAGE] from the main menu, and display the sub-menu.
Refer to “Navigating through the menu” (x page 51) for the operation of the menu screen.
ffPress as to select a language, and press the <ENTER> button to set.
Changing the display language
You can select the language of the on-screen display.
DISPLAY LANGUAGE
●
日本語
ffVarious menus, settings, adjustment screens, control button names, etc., are displayed in the selected language.
ffThe language can be changed to English, German, French, Spanish, Italian, Japanese, Chinese, Russian, and Korean.
Note
ffThe on-screen display language of the projector is set to English by default, and also when [ALL USER DATA] (x page 84) is executed
from [INITIALIZE].
ENGLISH - 67
Chapter 4 Settings — [DISPLAY OPTION] menu
[DISPLAY OPTION] menu
Select [DISPLAY OPTION] from the main menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” (x page 51) for the operation of the menu screen.
ffAfter selecting the item, press asqw to set.
[COLOR MATCHING]
You can correct the color difference between the sets when multiple sets are to be used simultaneously.
To adjust the color matching as desired
1) Press as to select [COLOR MATCHING].
2) Press qw to switch [COLOR MATCHING].
ffThe setting will change among [OFF], [3COLORS], [7COLORS]
and [MEASURED] each time you press the button.
3) Select [3COLORS] or [7COLORS], and press
the <ENTER> button.
ffThe [3COLORS] or [7COLORS] screen is displayed.
4) Press as to select [RED], [GREEN] or [BLUE]
([RED], [GREEN], [BLUE], [CYAN], [MAGENTA],
[YELLOW], or [WHITE] for [7COLORS]).
5) Press the <ENTER> button.
ffThe [3COLORS:RED], [3COLORS:GREEN], [3COLORS:BLUE],
or [3COLORS:WHITE] screen is displayed.
In the case of [7COLORS], the [7COLORS:RED],
[7COLORS:GREEN], [7COLORS:BLUE], [7COLORS:CYAN],
[7COLORS:MAGENTA], [7COLORS:YELLOW], or
[7COLORS:WHITE] screen is displayed.
6) Press as to select [RED], [GREEN], or [BLUE].
ffIf [WHITE] is selected from [3COLORS], only [GAIN] can be
adjusted.
7) Press qw to adjust.
ffAdjustment value will change between 0* and 2 048.
*The lower limit differs depending on the color to be adjusted.
rr[COLOR MATCHING]
[OFF]
Color matching adjustment is not carried out.
[3COLORS]
The three colors [RED], [GREEN], and [BLUE] can be adjusted.
[7COLORS]
The seven colors [RED], [GREEN], [BLUE], [CYAN], [MAGENTA], [YELLOW], and [WHITE] can be
adjusted.
[MEASURED]
Refer to “To adjust the color matching using a colorimeter” (x page 68) for details about this mode.
Note
ffOperation when correcting the adjustment color
When the correction color same as the adjustment color is changed: The luminance of the adjustment color changes.
When correction color red is changed: Red is added to or subtracted from the adjustment color.
When correction color green is changed: Green is added to or subtracted from the adjustment color.
When correction color blue is changed: Blue is added to or subtracted from the adjustment color.
ffThis adjustment should be carried out by a person who is familiar with the projector or by a service person because a high level of skill is
required to make a successful adjustment.
ffPressing the <DEFAULT> button will restore the factory default settings for all items.
ffWhen [COLOR MATCHING] is set to other than [OFF], [AI] and [COLOR CORRECTION] are fixed to [OFF], and [COLOR TEMPERATURE]
is fixed to [USER]. (However, [WHITE BALANCE HIGH] cannot be adjusted.)
To adjust the color matching using a colorimeter
Use a colorimeter that can measure chromaticity coordinates and luminance to change the colors [RED], [GREEN], [BLUE], [CYAN],
[MAGENTA], [YELLOW], and [WHITE] to desired colors.
1) Press as to select [COLOR MATCHING].
2) Press qw to select [MEASURED].
68 - ENGLISH
3) Press the <ENTER> button.
ffThe [MEASURED MODE] screen is displayed.
4) Press as to select [MEASURED DATA].
Chapter 4 Settings — [DISPLAY OPTION] menu
5) Press the <ENTER> button.
9) Press as to select [TARGET DATA].
ffThe [MEASURED DATA] screen is displayed.
10)Press the <ENTER> button.
6) Measure the current luminance (Y) and the
ffThe [TARGET DATA] screen is displayed.
chromaticity coordinates (x, y) using the
colorimeter.
11)Press as to select a color, and press qw to
7) Press as to select a color, then press qw to
adjust the value.
input coordinates for desired colors.
12)Once all the input is completed, press the
<MENU> button.
8) Once all the input is completed, press the
<MENU> button.
ffThe [MEASURED MODE] screen is displayed.
Note
ffColors are not displayed properly when target data is a color outside the region of this projector.
ffSet the [AUTO TESTPATTERN] to [ON] to automatically display a test pattern for use in adjusting the selected adjustment colors.
ffWhen using a colorimeter or similar instrument to measure measurement data, measure the colors displayed with [AUTO TESTPATTERN].
ffA difference in the color coordinates of target data and measurement values obtained from an instrument may occur for certain instruments
and measurement environments used.
[COLOR CORRECTION]
Colors can be adjusted and registered for each input signal format.
1) Press as to select [COLOR CORRECTION].
2) Press qw to switch [COLOR CORRECTION].
rr[COLOR CORRECTION]
[OFF]
[USER]
Standard setting
For each of the four signal formats, VIDEO, S-VIDEO, RGB, and YCBCR/YPBPR, six colors including red,
green, blue, cyan, magenta, and yellow can be adjusted and registered. Press the <ENTER> button to set
details. The adjustment range is between -30 and +30.
[CONTRAST MODE]
There are two modes. Set according to the operating environment.
1) Press as to select [CONTRAST MODE].
2) Press qw to switch [CONTRAST MODE].
rr[CONTRAST MODE]
[NORMAL]
[HIGH]
Maximizes brightness.
Maximizes contrast.
[SCREEN SETTING]
Set the screen size.
When changing the aspect of a projected image, correct to the optimum image position for the set screen. Set as necessary for the screen in
use.
1) Press as to select [SCREEN SETTING].
2) Press the <ENTER> button.
ffThe [SCREEN SETTING] screen is displayed.
3) Press qw to switch [SCREEN FORMAT].
ffThe setting will change between [16:10] and [16:9] for
PT-DW740E, or [4:3] and [16:9] for PT-DX810E.
4) Press as to select [SCREEN POSITION].
5) Press qw to adjust [SCREEN POSITION].
rr[SCREEN FORMAT]
PT-DW740E
[16:10]
Cannot be adjusted.
[16:9]
Vertical position can be adjusted between -40 and
40.
[4:3]
PT-DX810E
[16:9]
[SCREEN POSITION]
Cannot be adjusted.
Vertical position can be adjusted between -96 and
96.
ENGLISH - 69
Chapter 4 Settings — [DISPLAY OPTION] menu
[AUTO SIGNAL]
Set automatic execution of auto setup.
The screen display position or signal level can be adjusted automatically without pressing the <AUTO SETUP> button on the remote control on
each occasion if you input unregistered signals frequently at meetings, etc.
1) Press as to select [AUTO SIGNAL].
2) Press qw to switch [AUTO SIGNAL].
ffThe setting will change between [OFF] and [ON] each time you
press the button.
rr[AUTO SIGNAL]
[OFF]
Set input auto setup to off.
[ON]
Auto setup is automatically executed when images are changed to unregistered signals during projection.
[AUTO SETUP]
You can set when adjusting a special signal or horizontally long (16:9, etc.) signal.
1) Press as to select [AUTO SETUP].
2) Press the <ENTER> button.
ffThe [AUTO SETUP] screen is displayed.
3) Press qw to switch [MODE].
ffThe setting will change among [DEFAULT], [WIDE], and [USER]
each time you press the button.
ffWhen [DEFAULT] or [WIDE] is selected, proceed to Step 6).
ffWhen [USER] is selected, proceed to Step 4).
4) Press as to select [DISPLAY DOTS], and
press qw to adjust [DISPLAY DOTS] to the
horizontal resolution of the signal source.
5) Press as to select [MODE].
6) Press the <ENTER> button.
ffAutomatic adjustment is executed. [PROGRESS] is displayed
while automatically adjusting. When complete, the system
returns to the [AUTO SETUP] screen.
rr[MODE]
[DEFAULT]
Select when receiving a signal whose image aspect is 4:3 or 5:4. (Supported resolutions are 640 x 400,
640 x 480, 800 x 600, 832 x 624, 1 024 x 768, 1 152 x 864, 1 152 x 870, 1 280 x 960, 1 280 x 1 024, 1 600
x 1 200, and 1 400 x 1 050.)
[WIDE]
Select when receiving a signal whose image aspect is wide-screen. (Supported resolutions are 1 280 x
720, 1 280 x 800, 1 440 x 900, 1 680 x 1 050, 1 920 x 1 080, and 1 920 x 1 200.)
[USER]
Select when receiving a signal with a special horizontal resolution (number of display dots).
[RGB IN]
Set to match the signal to input to the <RGB 1 IN> terminal.
1) Press as to select [RGB IN].
2) Press the <ENTER> button.
ffThe [RGB IN] screen is displayed.
3) Press as to select [RGB1 SYNC SLICE
4) Press qw to switch between [RGB1 SYNC
SLICE LEVEL] and [RGB2 SYNC SLICE
LEVEL].
ffThe setting will change between [LOW] and [HIGH] each time
you press the button.
LEVEL] or [RGB2 SYNC SLICE LEVEL].
rr[RGB1 SYNC SLICE LEVEL] and [RGB2 SYNC SLICE LEVEL]
[LOW]
Set the slice level to [LOW].
[HIGH]
Set the slice level to [HIGH].
[DVI-D IN]
Switch the setting when the external equipment is connected to the <DVI-D IN> terminal of the projector and the image is not projected
correctly.
1) Press as to select [DVI-D IN].
2) Press the <ENTER> button.
ffThe [DVI-D IN] screen is displayed.
3) Press as to select [DVI EDID].
70 - ENGLISH
4) Press qw to switch [DVI EDID].
ffThe setting will change among [EDID3], [EDID1],
and[EDID2:PC] each time you press the button.
5) Press as to select [DVI SIGNAL LEVEL].
Chapter 4 Settings — [DISPLAY OPTION] menu
6) Press qw to switch [DVI SIGNAL LEVEL].
ffThe setting will change between [0-255:PC] and [16-235] each
time you press the button.
rr[DVI EDID]
[EDID3]
Switch between fine settings for a moving image and for a still image.
[EDID1]
Select mainly when an external device that outputs movie-type image signals (such as a blu-ray disk
player) is connected to the <DVI-D IN> terminal.
[EDID2:PC]
Select mainly when an external device that outputs still image-type signals (such as a computer) is
connected to the <DVI-D IN> terminal.
rr[DVI SIGNAL LEVEL]
[0-255:PC]
[16-235]
Select when an external device (such as a computer) is connected via DVI terminal output.
Select when an external device (such as a blu-ray disc player) is connected via HDMI terminal output by
use of a conversion cable or similar cable.
Note
ffThe optimal setting is different depending on the output setting of the connected external equipment. Refer to the instruction manual of the
external equipment regarding the output of the external equipment.
ffThe data for Plug and play will change when the setting is changed. Refer to “List of compatible signals” (x page 125) for a resolution that
supports plug and play.
[HDMI IN]
Switch the setting when the projector is connected to an external device via an HDMI cable and the image is not projected correctly.
1) Press as to select [HDMI IN].
2) Press the <ENTER> button.
3) Press qw to switch [HDMI SIGNAL LEVEL].
ffThe setting will change between [64-940] and [0-1023] each
time you press the button.
ffThe [HDMI IN] screen is displayed.
rr[HDMI SIGNAL LEVEL]
[64-940]
Select when the HDMI terminal of an external device (such as a blu-ray disc player) is connected to the
<HDMI IN> terminal.
[0-1023]
Select when the DVI-D terminal output of an external device (such as a computer) is connected to the
<HDMI IN> terminal via a conversion cable or similar cable.
Select also when the HDMI terminal output of a computer or other device is connected to the <HDMI IN>
terminal.
Note
ffThe optimal setting is different depending on the output setting of the connected external equipment. Refer to the instruction manual of the
external equipment regarding the output of the external equipment.
ffThe HDMI signal level is displayed per each 30 bits of input.
[ON-SCREEN DISPLAY]
Set the on-screen display.
1) Press as to select [ON-SCREEN DISPLAY].
2) Press the <ENTER> button.
ffThe [ON-SCREEN DISPLAY] screen is displayed.
3) Press as to select [OSD POSITION], [OSD
DESIGN], [OSD MEMORY], [INPUT GUIDE],
or [WARNING MESSAGE], then press qw to
adjust it.
4) Press qw to switch the setting.
ff[2] - [9], [1] in [OSD POSITION], [1] - [6] in [OSD DESIGN], [ON]/
[OFF] in [OSD MEMORY], [INPUT GUIDE], and [WARNING
MESSAGE] will change each time you press the button.
ENGLISH - 71
Chapter 4 Settings — [DISPLAY OPTION] menu
rr[ON-SCREEN DISPLAY]
[OSD POSITION]
[OSD DESIGN]
[OSD MEMORY]
[INPUT GUIDE]
[WARNING MESSAGE]
[2]
Set the position of the menu screen (OSD) to the center left of the screen.
[3]
Set the position of the menu screen (OSD) to the bottom left of the screen.
[4]
Set the position of the menu screen (OSD) to the top center of the screen.
[5]
Set the position of the menu screen (OSD) to the center of the screen.
[6]
Set the position of the menu screen (OSD) to the bottom center of the screen.
[7]
Set the position of the menu screen (OSD) to the top right of the screen.
[8]
Set the position of the menu screen (OSD) to the center right of the screen.
[9]
Set the position of the menu screen (OSD) to the bottom right of the screen.
[1]
Set the position of the menu screen (OSD) to the top left of the screen.
[1]
Set the color of the menu screen (OSD) to yellow.
[2]
Set the color of the menu screen (OSD) to blue.
[3]
Set the color of the menu screen (OSD) to white.
[4]
Set the color of the menu screen (OSD) to green.
[5]
Set the color of the menu screen (OSD) to pink.
[6]
Set the color of the menu screen (OSD) to brown.
[ON]
[OFF]
[ON]
[OFF]
[ON]
[OFF]
Set hold for the position of the menu screen (OSD) cursor.
Set display of the input terminal name currently selected in the position set by the
[OSD POSITION].
You can set the display/hide of the warning message.
Note
ffEven if [OSD MEMORY] is set to [ON], the cursor position will not be held when the <MAIN POWER> switch of the projector body is turned
<OFF>.
[BACK COLOR]
Set the color of the projected image when there is no signal input.
1) Press as to select [BACK COLOR].
2) Press qw to switch [BACK COLOR].
ffThe setting will change among [BLUE], [BLACK], [DEFAULT
LOGO] and [USER LOGO] each time you press the button.
rr[BACK COLOR]
[BLUE]
The entire projection area appears blue.
[BLACK]
The entire projection area appears black.
[DEFAULT LOGO]
[USER LOGO]
The Panasonic logo is projected.
The picture registered by the user is projected.
Note
ffTo create the image for [USER LOGO], “Logo Transfer Software” included in the supplied CD-ROM is required.
[STARTUP LOGO]
Set the logo display when the power is turned on.
1) Press as to select [STARTUP LOGO].
2) Press qw to switch [STARTUP LOGO].
ffThe setting will change among [DEFAULT LOGO], [USER
LOGO], and[NONE] each time you press the button.
rr[STARTUP LOGO]
[DEFAULT LOGO]
[USER LOGO]
[NONE]
72 - ENGLISH
The Panasonic logo is projected.
The picture registered by the user is projected.
No startup logo is projected.
Chapter 4 Settings — [DISPLAY OPTION] menu
Note
ffThe startup logo will disappear in approximately 15 seconds.
ffTo create the image for [USER LOGO], “Logo Transfer Software” included in the supplied CD-ROM is required.
[SHUTTER SETTING]
Set the opening and closing status of the shutter for when projection begins by switching on the projector, and for when the projector is
switched off.
To set [STARTUP]
1) Press as to select [SHUTTER SETTING].
3) Press as to select [STARTUP].
2) Press the <ENTER> button.
4) Press qw to switch.
ffThe setting will change between [OPEN] and [CLOSE] each
time you press the button.
ffThe [SHUTTER SETTING] screen is displayed.
rr[STARTUP]
[OPEN]
[CLOSE]
Projection begins with the shutter open when the power is turned on.
Projection begins with the shutter closed when the power is turned on.
To set [SHUT-OFF]
1) Press as to select [SHUTTER SETTING].
3) Press as to select [SHUT-OFF].
2) Press the <ENTER> button.
4) Press qw to switch.
ffThe setting will change among [KEEP CURRENT STATE],
[CLOSE], and[OPEN] each time you press the button.
ffThe [SHUTTER SETTING] screen is displayed.
rr[SHUT-OFF]
[KEEP CURRENT STATE]
[CLOSE]
[OPEN]
Enters standby with the opening and closing status of the shutter same as before switching off the projector.
Enters standby with the shutter closed.
Enters standby with the shutter open.
Note
ffIt is recommended that you set the projector to enter standby with the shutter closed when you remove the projection lens for transport of
the set, etc. so that dust will not enter.
ffWhen switching off the projector, the [POWER OFF(STANDBY)] confirmation screen appears regardless of the opening and closing status
of the shutter at that moment.
[FREEZE]
The projected image is paused temporarily regardless of the playback of the external equipment.
1) Press as to select [FREEZE].
2) Press the <ENTER> button.
ffPress the <MENU> button to release.
[SIDE BY SIDE](PT-DW740E only)
Displays two different input signals simultaneously.
1) Press as to select [SIDE BY SIDE].
4) Press as to select the image to display on
the Input B side.
2) Press the <ENTER> button.
ffPress as to select an image to display on the right side of the
screen (Input B).
ffDisplays the side-by-side screen.
5) Press the <ENTER> button.
Input A
Input A
Input B
3) Press the <MENU> button.
ffThe [SUB INPUT SELECT] screen is displayed.
ENGLISH - 73
Chapter 4 Settings — [DISPLAY OPTION] menu
rrSetting the two window display
[VIDEO]
[S-VIDEO]
Displays images of [VIDEO] input on the right screen (Input B).
Displays images of [S-VIDEO] input on the right screen (Input B).
[RGB1]
Displays images of [RGB1] input on the right screen (Input B).
[RGB2]
Displays images of [RGB2] input on the right screen (Input B).
[DVI-D]
Displays images of [DVI-D] input on the right screen (Input B).
[HDMI]
Displays images of [HDMI] input on the right screen (Input B).
[OFF]
Cancels the two window display.
Note
ff[FREEZE] is set on the Input A side.
ffDuring the two window display, menu items cannot be adjusted or set.
ffThe value of the Input A side is applied to the [PICTURE] setting. (For [CONTRAST], [BRIGHTNESS], [COLOR], [TINT], and [SHARPNESS],
respective values of both Input A and B are applied.)
ffThe two window display maintains the aspect ratio selected with the <ASPECT> button on the remote control or the setting of [ASPECT].
ffThe two window display may not be available depending on the combination of input signals.
Refer to “Two window display combination list (PT-DW740E only)” (x page 125) for details.
[CUT OFF]
Each red, green and blue color component can be removed.
1) Press as to select [CUT OFF].
3) Press as to select [RED], [GREEN], or [BLUE].
2) Press the <ENTER> button.
4) Press qw to switch.
ffThe [CUT OFF] screen is displayed.
ffThe setting will change between [OFF] and [ON] each time you
press the button.
rr[RED], [GREEN], and [BLUE]
[OFF]
Disables cutoff.
[ON]
Enables cutoff.
Note
ffWhen input is switched or a signal is switched, the cutoff setting returns to its original setting ([OFF]).
74 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
[PROJECTOR SETUP] menu
Select [PROJECTOR SETUP] from the main menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” (x page 51) for the operation of the menu screen.
ffAfter selecting the item, press asqw to set.
[PROJECTOR ID]
The projector has an ID number setting function that can be used when multiple projectors are used side by side to enable simultaneous
control or individual control via one remote control.
1) Press as to select [PROJECTOR ID].
2) Press qw to switch [PROJECTOR ID].
ffThe setting will change among [ALL] and [1] to [64] each time
you press the button.
rr[PROJECTOR ID]
[ALL]
[1] - [64]
Set to control without specifying an ID number.
Set to control specifying an ID number for individual control.
Note
ffThe ID number can be set to [ALL], or from [1] to [64].
ffTo specify an ID number for individual control, the ID number of a remote control must match the ID number of the projector.
ffWhen the ID number is set to [ALL], the projector will operate regardless of the ID number specified during remote control or computer
control.
If multiple projectors are set up side by side with IDs set to [ALL], they cannot be controlled separately from the projectors with other ID
numbers.
ffRefer to “Setting Remote control ID numbers” (x page 23) regarding the method to set the ID number on the remote control.
[PROJECTION METHOD]
Set the projection method in accordance with the installation status of the projector.
Change the projection method if the screen display is upside down or inverted.
1) Press as to select [PROJECTION METHOD].
3) Press as to select a projection method.
2) Press the <ENTER> button.
4) Press the <ENTER> button.
ffThe [PROJECTION METHOD] screen is displayed.
5) When the confirmation is displayed, select [OK]
or [CANCEL], and press the <ENTER> button.
rrAvailable projection methods
[FRONT/FLOOR]
When installing on the desk, etc., in front of the screen
[FRONT/CEILING]
When installing using the ceiling mount bracket (optional accessories) in front of the screen
[REAR/FLOOR]
When installing on the desk, etc., behind the screen (using a translucent screen)
[REAR/CEILING]
When installing using the ceiling mount bracket (optional accessories) behind the screen (using a
translucent screen)
Attention
ffWhen [PROJECTION METHOD] is changed, confirm that [COOLING CONDITION] (x page 76) is set correctly.
ENGLISH - 75
Chapter 4 Settings — [PROJECTOR SETUP] menu
[COOLING CONDITION]
Change the fan control depending on the direction of projection.
Set [COOLING CONDITION] correctly in accordance with the direction of projection referring to the following figure. It may shorten the life of
the lamp if used in incorrect setting.
[UPWARD SETTING]
[FLOOR SETTING]
30°
30° [CEILING SETTING]
30°
30°
[DOWNWARD SETTING]
： Projection direction
1) Press as to select [COOLING CONDITION].
2) Press the <ENTER> button.
ffThe [COOLING CONDITION] screen is displayed.
3) Press as to select a cooling condition.
4) Press the <ENTER> button.
5) When the confirmation is displayed, select [OK]
or [CANCEL], and press the <ENTER> button.
[HIGH ALTITUDE MODE]
Set to [ON] to use the projector at 1 400 m (4 593 ft) to 2 700 m (8 858 ft) elevations.
1) Press as to select [HIGH ALTITUDE MODE].
2) Press qw to switch [HIGH ALTITUDE MODE].
3) When the confirmation is displayed, select [OK]
or [CANCEL], and press the <ENTER> button.
ffThe setting will change between [OFF] and [ON].
rr[HIGH ALTITUDE MODE]
[OFF]
When using at a place lower than 1 400 m (4 593 ft) above sea level
[ON]
When using at a high altitude (1 400 m (4 593 ft) or higher and lower than 2 700 m (8 858 ft) above sea
level)
Note
ffThe speed of the fan increases and the operation sound becomes louder when set to [ON].
[LAMP SELECT]
Switch between brightness of two lamps and that of single lamp from the two luminous lamps built into the projector body according to the
use condition or purpose. When [SINGLE] is set, the lamp to be turned on is automatically selected based on the cumulative operating time of
lamps.
1) Press as to select [LAMP SELECT].
2) Press qw to switch [LAMP SELECT].
ffThe setting will change among [DUAL], [SINGLE], [LAMP1] and
[LAMP2] each time you press the button.
3) Press the <ENTER> button.
rr[LAMP SELECT]
[DUAL]
Two lamps will light.
[SINGLE]
Single lamp will light. (The lamp with shorter cumulative operating time is selected automatically.)
[LAMP1]
Lamp 1 will light.
[LAMP2]
Lamp 2 will light.
Note
ffWhen [SINGLE], [LAMP1], or [LAMP2] is selected, if the lamp does not light or the cumulative operating time exceeds 2000 hours (when
[LAMP POWER] is set to [NORMAL]), the other lamp will light. When [DUAL] is selected, if either lamp does not light or the cumulative
76 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
operating time of either of them exceeds 2000 hours (when [LAMP POWER] is set to [NORMAL]), only the other lamp will light. However, if
both lamps do not light, or the cumulative operating time of both of them exceeds 2000 hours (when [LAMP POWER] is set to [NORMAL]),
the projector will go into standby.
ffThe font colors of the items indicate the status.
Green → Current setting
Yellow → Current setting (when there is a lamp that cannot turn on or failed to turn on)
Red → Lamp that has failed to turn on
White → Any other status
ffRepeatedly switching in a short time will increase the speed of the lamp replacement cycle.
[LAMP RELAY]
The lamp to be turned on can be automatically switched by specifying the day of the week and time.
The degradation of the lamp due to continuous usage can be reduced by automatically switching the lamp to be turned on when using the
projector continuously for 1 week or more.
1) Press as to select [LAMP RELAY].
5) Press qw to select [HOUR] or [MINUTE], and
then press as to adjust it.
2) Press qw to switch [LAMP RELAY].
ffHours only can be adjusted with one hour increments when
[HOUR] is selected and minutes only can be adjusted with
one minute increments between 00 and 59 when [MINUTE] is
selected.
ffThe setting will change among [OFF], [24H], and [1WEEK] each
time you press the button.
3) Press as to select [TIME].
4) Press the <ENTER> button.
ffEnters adjustment mode (the display is blinking).
6) Press the <ENTER> button.
ffThe adjusted time is established.
7) Press as to select [DAY OF THE WEEK].
8) Press qw to switch [DAY OF THE WEEK].
ffThe setting will change among [SUNDAY], [MONDAY],
[TUESDAY], [WEDNESDAY], [THURSDAY], [FRIDAY] and
[SATURDAY] each time you press the button.
rr[LAMP RELAY]
[OFF]
Disables lamp relay.
[24H]
Switches lamps on a day-to-day basis.
[1WEEK]
Switches lamps on a week-to-week basis.
rr[DAY OF THE WEEK]
[SUNDAY]
[MONDAY]
[TUESDAY]
[WEDNESDAY]
The lamp to be turned on will be switched automatically on the set day of the week.
[THURSDAY]
[FRIDAY]
[SATURDAY]
Note
ffThe [LAMP RELAY] function is enabled when [DUAL] or [SINGLE] is selected in [LAMP SELECT].
ffThe operating time will be the local time. (x page 83)
ffUse the number (<0> to <9>) buttons on the remote control to directly enter the time.
[LAMP POWER]
Switch lamp brightness according to the operating environment or purpose of the projector.
1) Press as to select [LAMP POWER].
2) Press qw to switch [LAMP POWER].
ffThe setting will change between [NORMAL] and [ECO] each
time you press the button.
rr[LAMP POWER]
[NORMAL]
[ECO]
Set when high luminance is required.
Set when high luminance is not required.
ENGLISH - 77
Chapter 4 Settings — [PROJECTOR SETUP] menu
Note
ffWhen [ECO] is set, the power consumption and operation sound can be reduced while the lamp life can be increased.
[STANDBY MODE]
Set the power consumption during the standby.
1) Press as to select [STANDBY MODE].
2) Press qw to switch [STANDBY MODE].
ffThe setting will change between [NORMAL] and [ECO] each
time you press the button.
rr[STANDBY MODE]
[NORMAL]
[ECO]
Normally use this setting.
Use this setting to reduce power consumption during standby.
Note
ffWhen set to [ECO], network functions and <SERIAL OUT> terminal are not available during standby. Also, some RS-232C commands are
not available. When set to [NORMAL], network functions and <SERIAL OUT> terminal are available during standby.
ffWhen set to [ECO], display may delay about 10 seconds when the power is turned on, compared to the [NORMAL] setting.
[SCHEDULE]
Set the command execution schedule for each day of the week.
Enabling/disabling the schedule function
1) Press as to select [SCHEDULE].
2) Press qw to switch [SCHEDULE].
ffThe setting will change between [OFF] and [ON] each time you
press the button.
rr[SCHEDULE]
[OFF]
Disables the schedule function.
[ON]
Enables the schedule function. Refer to “How to assign a program” (x page 78) or “How to set a
program” (x page 78) in regard to how to set the schedule.
Note
ffWhen [SCHEDULE] is set to [ON], the [STANDBY MODE] setting is forcibly switched to [NORMAL], and the setting cannot be changed.
Even if [SCHEDULE] is then set to [OFF] when in this state, the setting of [STANDBY MODE] remains at [NORMAL].
How to assign a program
1) Press as to select [SCHEDULE].
2) Press qw to select [ON], and press the
<ENTER> button.
ffThe [SCHEDULE] screen is displayed.
3) Select and assign program to each day of
week.
ffPress as to select the day of week, and press qw to select a
program number.
ffYou can set the program from No.1 to No.7. “- - -” indicates that
the program number has not been set yet.
How to set a program
You can set up to 16 commands to each program.
1) Press as to select [SCHEDULE].
2) Press qw to select [ON], and press the
<ENTER> button.
ffThe [SCHEDULE] screen is displayed.
3) Press as to select [PROGRAM EDIT].
4) Press qw to select a program number and
then press the <ENTER> button.
5) Press as to select a command number and
press the <ENTER> button.
ffYou can change the page using qw.
6) Press as to select [TIME], and press the
<ENTER> button.
7) Press qw to select hour and minute, and press
as or the number (<0> to <9>) buttons to set
a time, and press the <ENTER> button.
8) Press as to select [COMMAND].
78 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
9) Press qw to switch [COMMAND].
11)Press as to select a command.
ffThe setting will change among [POWER ON], [STANDBY],
[SHUTTER]*1, [INPUT]*1, [LAMP SELECT]*1, [LAMP POWER]*1
and [SIDE BY SIDE]*1*2 each time you press the button.
*1 The details set in step 11) are displayed.
*2 Only for PT-DW740E
10)Press the <ENTER> button.
ff[OPEN]/[CLOSE] in [SHUTTER], [RGB1]/[RGB2]/[VIDEO]/
[S-VIDEO]/[DVI-D]/[HDMI] in [INPUT], [DUAL]/[SINGLE] in
[LAMP SELECT], [NORMAL]/[ECO] in [LAMP POWER], and
[OFF]/[ON] in [SIDE BY SIDE] will change each time you press
qw.
12)Press the <ENTER> button.
ffThe [COMMAND] detailed screen is displayed.
ffThe command is fixed and ● is displayed at the left of the
selected command.
ffAfter the command is fixed, press the <MENU> button to close
the detailed setting menu.
13)Press as to select [STORE], and press the
<ENTER> button.
rr[COMMAND]
[POWER ON]
[STANDBY]
[SHUTTER]
[INPUT]
[LAMP SELECT]
[LAMP POWER]
―
Turns the power on.
―
Enters standby.
[OPEN]
Opens the shutter.
[CLOSE]
Closes the shutter.
[RGB1]
Switches the input to RGB1.
[RGB2]
Switches the input to RGB2.
[VIDEO]
Switches the input to VIDEO.
[S-VIDEO]
[DVI-D]
Switches the input to DVI-D.
[HDMI]
Switches the input to HDMI.
[DUAL]
Turns on both lamps.
[SINGLE]
[NORMAL]
[SIDE BY SIDE]*
Switches the input to S-VIDEO.
Turns on one lamp. (The lamp is automatically selected which has shorter
cumulative operating time.)
Sets the high luminance of the lamp.
[ECO]
Sets lower luminance of the lamp than [NORMAL].
[OFF]
Displays the side-by-side screen.
[ON]
Cancels the side-by-side screen.
*Only for PT-DW740E
Note
ffIf you try to register a setting that would cause the lamp to flash for a short time, an error message will be displayed on the screen. Set the
time and command again.
ffTo delete a command already set, press the <DEFAULT> button on the Step 5) screen, or select [DELETE] on the Step 6) screen and press
the <ENTER> button.
ffIf multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
ffThe operating time will be the local time. (x page 83)
ffIf an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with this function may not be executed.
[STARTUP INPUT SELECT]
Set the input signal to be projected when the projector is switched on.
1) Press as to select [STARTUP INPUT
SELECT].
2) Press qw to switch [STARTUP INPUT
SELECT].
ffThe setting will change among [LAST USED], [RGB1], [RGB2],
[VIDEO], [S-VIDEO], [DVI-D] and [HDMI] each time you press
the button.
rr[STARTUP INPUT SELECT]
[LAST USED]
Keeps the input selected last.
[RGB1]
Sets the input to be projected when the projector is switched on to RGB1.
[RGB2]
Sets the input to be projected when the projector is switched on to RGB2.
[VIDEO]
Sets the input to be projected when the projector is switched on to VIDEO.
ENGLISH - 79
Chapter 4 Settings — [PROJECTOR SETUP] menu
[S-VIDEO]
Sets the input to be projected when the projector is switched on to S-VIDEO.
[DVI-D]
Sets the input to be projected when the projector is switched on to DVI-D.
[HDMI]
Sets the input to be projected when the projector is switched on to HDMI.
[RS-232C]
Set the communication conditions of the <SERIAL IN>/<SERIAL OUT> terminal.
To set the communication condition of the <SERIAL IN> terminal
1) Press as to select [RS-232C].
2) Press the <ENTER> button.
ffThe [RS-232C] screen is displayed.
3) Press as to select [(IN) BAUDRATE].
4) Press qw to switch [(IN) BAUDRATE].
ffThe setting will change among [9600], [19200], and [38400]
each time you press the button.
5) Press as to select [(IN) PARITY].
6) Press qw to switch [(IN) PARITY].
ffThe setting will change among [NONE], [EVEN], and [ODD]
each time you press the button.
rr[(IN) BAUDRATE]
[9600]
[19200]
Select the proper speed.
[38400]
rr[(IN) PARITY]
[NONE]
[EVEN]
Select the parity condition.
[ODD]
To set the communication condition of the <SERIAL OUT> terminal
1) Press as to select [RS-232C].
2) Press the <ENTER> button.
ffThe [RS-232C] screen is displayed.
3) Press as to select [(OUT) BAUDRATE].
4) Press qw to switch [(OUT) BAUDRATE].
ffThe setting will change among [9600], [19200], and [38400]
each time you press the button.
5) Press as to select [(OUT) PARITY].
6) Press qw to switch [(OUT) PARITY].
ffThe setting will change among [NONE], [EVEN], and [ODD]
each time you press the button.
rr[(OUT) BAUDRATE]
[9600]
[19200]
Select the proper speed.
[38400]
rr[(OUT) PARITY]
[NONE]
[EVEN]
Select the parity condition.
[ODD]
To set the response
1) Press as to select [RS-232C].
2) Press the <ENTER> button.
ffThe [RS-232C] screen is displayed.
3) Press as to select [RESPONSE(ID ALL)].
80 - ENGLISH
4) Press qw to switch [RESPONSE(ID ALL)].
ffThe setting will change between [ON] and [OFF] each time you
press the button.
5) Press as to select [GROUP].
Chapter 4 Settings — [PROJECTOR SETUP] menu
6) Press qw to switch [GROUP].
8) Press qw to switch [RESPONSE(ID GROUP)].
ffThe setting will change among [A] to [Z] each time you press
the button.
ffThe setting will change between [ON] and [OFF] each time you
press the button.
7) Press as to select [RESPONSE(ID GROUP)].
rr[RESPONSE(ID ALL)]
[ON]
Returns the response when the ID setting is ALL.
[OFF]
Does not return the response when the ID setting is ALL.
rr[GROUP]
Controls multiple projectors simultaneously by sending the ID of RS-232C.
Set the group from [A] to [Z]. The projector responds when the ID of RS-232C matches the setting.
[A] - [Z]
rr[RESPONSE(ID GROUP)]
[ON]
Returns the response when the ID setting is GROUP.
[OFF]
Does not return the response when the ID setting is GROUP.
Note
ffRefer to “<SERIAL IN>/<SERIAL OUT> terminal” (x page 121).
[REMOTE2 MODE]
You can set the <REMOTE 2 IN> terminal.
1) Press as to select [REMOTE2 MODE].
3) Press the <ENTER> button.
2) Press qw to switch [REMOTE2 MODE].
4) Press as to select any from [PIN2] to [PIN8]
ffThe setting will change between [DEFAULT] and [USER] each
time you press the button.
ffWhen [USER] is selected, proceed to Step 3).
and press qw to switch the setting.
ff[PIN1] and [PIN9] cannot be changed.
rr[REMOTE2 MODE]
The pin assignment of the <REMOTE 2 IN> terminal is used by the factory default setting of the projector.
(x page 124)
[DEFAULT]
The pin assignment of the <REMOTE 2 IN> terminal is used by the setting changed from the factory default
setting of the projector.
[USER]
[STATUS]
Displays the status of the projector.
1) Press as to select [STATUS].
2) Press the <ENTER> button.
3) Press qw to switch the pages.
ffThe page will change each time you press the button.
ffThe [STATUS] screen is displayed.
rrContents to be displayed
[INPUT]
[SIGNAL NAME]
[SIGNAL FREQUENCY]
[PROJECTOR RUNTIME]
Displays the input terminal currently selected.
Displays the input signal name.
Displays the frequency of the input signal.
Displays the operation times of the projector.
[LAMP1]*
Displays the hours used of lamp 1.
[LAMP2]*
Displays the hours used of lamp 2.
[INTAKE AIR TEMP.]
[OPTICS MODULE TEMP.]
[AROUND LAMP TEMP.]
[PROJECTOR TYPE]
[SERIAL NUMBER]
[LAMP UNIT MODEL NO.]
Displays the status of the air intake temperature of the projector.
Displays the status of the internal temperature of the projector.
Displays the status of the temperature around the lamps of the projector.
Displays the type of the projector.
Displays the serial number of the projector.
Displays the model no. of the lamp unit.
ENGLISH - 81
Chapter 4 Settings — [PROJECTOR SETUP] menu
[LAMP1 SERIAL NUMBER]
Displays the serial number of the lamp 1.
[LAMP2 SERIAL NUMBER]
Displays the serial number of the lamp 2.
[MAIN VERSION]
Displays the main version of the firmware of the projector.
[SUB VERSION]
Displays the sub version of the firmware of the projector.
[NETWORK VERSION]
[POWER ON TIMES]
[ON COUNT]
Displays the network version of the projector.
Displays the number of times the power is turned on.
[LAMP1 ON]
Displays the number of times lamp 1 has been turned on.
[LAMP2 ON]
Displays the number of times lamp 2 has been turned on.
[SHUTTER]
Displays the number of times the shutter function has been used.
[LAMP1]
Displays the details of cumulative operating time.
[LAMP2]
Displays the details of cumulative operating time.
[NUMBER OF ENTRY SIGNAL]
[REMOTE2 STATUS]
[MEMORY NO.]
[INPUT]
[SIGNAL NAME]
[SIGNAL FREQUENCY]
[SYNC.STATE]
[SIGNAL INFORMATION]
[V.SYNC WIDTH]
Displays the number of registered signals.
Displays the control status of the REMOTE2.
Displays the memory number of the input signal.
Displays the input terminal currently selected.
Displays the input signal name.
Displays the frequency of the input signal.
Displays the synch polarity of the input signal.
Displays the vertical sync signal pulse width of the input signal.
[SCAN TYPE]
Displays the scan type of the input signal.
[TOTAL DOTS]
Displays the total dot count of the input signal.
[DISPLAY DOTS]
[TOTAL LINES]
[DISPLAY LINES]
[SAMPLING]
Displays the number of input signal display dots.
Displays the total line count of the input signal.
Displays the number of input signal display lines.
Displays the sampling information of the input signal.
*Displays the actual time for the hours used of lamp.
To calculate a rough guide for lamp replacement, convert as follows:
Lamp replacement time =
Cumulative operating time when [LAMP POWER] is set to [NORMAL] + (Cumulative operating time when [LAMP POWER] is set to [ECO] x
2/3)
Note
ffThe content of status can be sent via E-mail by pressing the <ENTER> button while displaying the status.
ffSome items in [SIGNAL INFORMATION] may be displayed and others not displayed, depending on the signal being input.
[NO SIGNAL SHUT-OFF]
You can set the power of the projector automatically to standby if there is no input signal by the specified time.
1) Press as to select [NO SIGNAL SHUT-OFF].
2) Press qw to switch [NO SIGNAL SHUT-OFF].
rr[NO SIGNAL SHUT-OFF]
[DISABLE]
[10MIN.] - [90MIN.]
Disables the No signal shut-off function.
Allows you to set in ten minutes intervals.
[FUNCTION BUTTON]
Set the functions of the <FUNCTION> button on the remote control.
1) Press as to select [FUNCTION BUTTON].
3) Press as to select a function.
2) Press the <ENTER> button.
4) Press the <ENTER> button.
ffThe [FUNCTION BUTTON] screen is displayed.
rrAvailable functions
[DISABLE]
[SUB MEMORY]
[SYSTEM SELECTOR]
82 - ENGLISH
Disables the <FUNCTION> button.
Switches the sub memory. (x page 87)
Switches the [SYSTEM SELECTOR] setting. (x page 59)
Chapter 4 Settings — [PROJECTOR SETUP] menu
[SYSTEM DAYLIGHT VIEW]
[FREEZE]
Switches the [SYSTEM DAYLIGHT VIEW] setting. (x page 57)
Temporarily freezes video to be a still image. (x page 73)
[SIDE BY SIDE]
*
Switches to the two window display. (x page 73)
*Only for PT-DW740E
[DATE AND TIME]
Set the time zone, date, and time of the built-in clock of the projector.
To set time zone
1) Press as to select [DATE AND TIME].
3) Press as to select [TIME ZONE].
2) Press the <ENTER> button.
4) Press qw to switch [TIME ZONE].
ffThe [DATE AND TIME] screen is displayed.
To set the date and time manually
1) Press as to select [DATE AND TIME].
2) Press the <ENTER> button.
ffThe [DATE AND TIME] screen is displayed.
3) Press as to select [ADJUST CLOCK].
5) Press as to select an item, and press qw to
set the local date and time.
6) Press as to select [APPLY], and press the
<ENTER> button.
ffThe setting of the time will be completed.
4) Press the <ENTER> button.
ffThe [ADJUST CLOCK] screen is displayed.
To set the date and time automatically
1) Press as to select [DATE AND TIME].
2) Press the <ENTER> button.
ffThe [DATE AND TIME] screen is displayed.
3) Press as to select [ADJUST CLOCK].
4) Press the <ENTER> button.
ffThe [ADJUST CLOCK] screen is displayed.
5) Press as to select [NTP SYNCHRONIZATION],
and press qw to change the setting to [ON].
ffThe setting will change between [ON] and [OFF] each time you
press the button.
6) Press as to select [APPLY], and press the
<ENTER> button.
ffThe setting of the time will be completed.
rr[NTP SYNCHRONIZATION]
[ON]
Enables [NTP SYNCHRONIZATION].
[OFF]
Disables [NTP SYNCHRONIZATION].
Note
ffTo set the date and time automatically, the projector must be connected to the network.
ffIf synchronization with the NTP server fails just after [NTP SYNCHRONIZATION] is turned [ON], or if [NTP SYNCHRONIZATION] is turned
[ON] while the NTP server is not set, [NTP SYNCHRONIZATION] will return to [OFF].
ffAccess the projector via a web browser to set the NTP server. Refer to “[Adjust clock] page” (x page 99) for details.
[SAVE ALL USER DATA]
Save the various setting values as a backup in the built-in memory of the projector.
1) Press as to select [SAVE ALL USER DATA].
2) Press the <ENTER> button.
ffThe [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the
<ENTER> button.
4) When the confirmation is displayed, select [OK]
or [CANCEL], and press the <ENTER> button.
ff[PROGRESS] is displayed while saving data.
Note
ffThe image setting registered in [USER LOGO] is not saved.
ENGLISH - 83
Chapter 4 Settings — [PROJECTOR SETUP] menu
[LOAD ALL USER DATA]
Load the various setting values saved as a backup in the built-in memory of the projector.
1) Press as to select [LOAD ALL USER DATA].
2) Press the <ENTER> button.
ffThe [SECURITY PASSWORD] screen is displayed.
3) Enter a security password and press the
<ENTER> button.
4) When the confirmation is displayed, select [OK]
or [CANCEL], and press the <ENTER> button.
Note
ffThe projector will go into the standby status to reflect the setting values when [LOAD ALL USER DATA] is executed.
[INITIALIZE]
Return various setting values to their factory default settings.
1) Press as to select [INITIALIZE].
4) Press as to select an item to initialize.
2) Press the <ENTER> button.
5) Press the <ENTER> button.
ffThe [SECURITY PASSWORD] screen is displayed.
3)
Enter a security password and press the
<ENTER> button.
6) When the confirmation is displayed, select [OK]
or [CANCEL], and press the <ENTER> button.
ffThe [INITIALIZE] screen is displayed.
rrItems that can be initialized
[ALL USER DATA]
All setting items including [ENTRY SIGNAL], [NETWORK SETUP], [E-mail set up], and [USER LOGO] are
returned to factory default values.
The projector will go into the standby status to reflect the setting values.
[ENTRY SIGNAL]
Deletes all the setting values saved for each input signal.
To delete only a part of a registered signal, perform the procedure described in “Deleting the registered
data” (x page 86).
[NETWORK/E-MAIL]
[LOGO IMAGE]
Returns [NETWORK SETUP] and [E-mail set up] to factory default settings.
Deletes the image registered in [USER LOGO].
[SERVICE PASSWORD]
Used by a service person.
84 - ENGLISH
Chapter 4 Settings — [TEST PATTERN] menu
[TEST PATTERN] menu
Select [TEST PATTERN] from the main menu.
Refer to “Navigating through the menu” (x page 51) for the operation of the menu screen.
ffPress qw to switch.
[TEST PATTERN]
Displays the test pattern built-in to the projector.
Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before performing various
adjustments.
1) Press qw to switch [TEST PATTERN].
ffThe setting will change among “Menu screen + Focus”, “Menu
screen + Entry screen”*, “Menu screen + All white”, “Menu
screen + All black”, “Menu screen + Flag”, “Menu screen + Flag
(inversion)”, “Menu screen + Window”, “Menu screen + Window
(inversion)”, “Menu screen + Color bar (vertical)”, and “Menu
screen + Color bar (horizontal)” each time you press the button.
*The test pattern built-in to the projector is not being displayed.
rr[TEST PATTERN]
Menu screen + Focus
Menu screen + Entry screen
Menu screen + All white
Menu screen + All black
Menu screen + Flag
Menu screen + Flag (inversion)
Displays a test pattern with the menu screen. Select a test pattern so that it is easy to
make various adjustments.
Menu screen + Window
Menu screen + Window (inversion)
Menu screen + Color bar (vertical)
Menu screen + Color bar (horizontal)
Note
ffPress the <ON SCREEN> button on the remote control while the test pattern is displayed to hide the menu screen.
ENGLISH - 85
Chapter 4 Settings — [SIGNAL LIST] menu
[SIGNAL LIST] menu
Select [SIGNAL LIST] from the main menu.
Refer to “Navigating through the menu” (x page 51) for the operation of the menu screen.
rrRegistered signal status
ffA name can be set for each sub memory (x page 87).
ffMemory number:
A1 (1-2)
Sub memory number
When the address number (A1, A2, ... H7,
H8) is registered
Registering a signal to the list
After a new signal is input and the <MENU> button on the remote control or the control panel is pressed, the registration is completed and the
[MAIN MENU] screen is displayed.
Note
ffUp to 96 signals, including sub memories, can be registered to the projector.
ffThere are 12 pages (eight memories of A through L, with eight memories possible on each page) for memory numbers, and it is registered to
the lowest number that is available. If there is no available memory number it will be overwritten from the oldest signal.
ffThe names to be registered are automatically determined by the input signals and memory numbers.
ffIf a menu is being displayed, the new signals will be registered at the instant they are input.
Renaming the registered data
Registered signals can be renamed.
1) Press asqw to select the signal for which
details are to be displayed.
2) Press the <ENTER> button.
ffThe [REGISTERED SIGNAL STATUS] screen is displayed.
ffThe memory number, input terminal, input signal name,
frequency, synchronization signal, etc., are displayed.
ffPress the <MENU> button to return to the [REGISTERED
SIGNAL LIST] screen.
3) Press the <ENTER> button.
ffThe [REGISTERED SIGNAL SETUP] screen is displayed.
4) Press as to select [SIGNAL NAME CHANGE].
5) Press the <ENTER> button.
ffThe [SIGNAL NAME CHANGE] screen is displayed.
6) Press asqw to select the text, and press the
<ENTER> button to enter the text.
7) After the name is changed, press asqw to
select [OK], and press the <ENTER> button.
ffThe registration is completed and it will return to the
[REGISTERED SIGNAL SETUP] screen.
ffWhen pressing asqw to select [CANCEL] and pressing
the <ENTER> button, the changed signal name will not be
registered and an automatically registered signal name will be
used.
Deleting the registered data
Registered signals can be deleted.
1) Press asqw to select the signal to delete.
2) Press the <DEFAULT> button.
ffThe [ENTRY SIGNAL DELETE] screen is displayed.
ffTo cancel the deletion, press the <MENU> button to return to
the [REGISTERED SIGNAL LIST] screen.
86 - ENGLISH
3) Press the <ENTER> button.
ffThe selected signal will be deleted.
Chapter 4 Settings — [SIGNAL LIST] menu
Note
ffA signal can also be deleted from [ENTRY SIGNAL DELETE] on the [REGISTERED SIGNAL SETUP] screen.
Protecting the registered data
Registered signals can be protected.
1) Press asqw to select the signal to protect.
4) Press as to select [LOCK].
2) Press the <ENTER> button.
5) Press qw to switch [LOCK].
ffThe [REGISTERED SIGNAL STATUS] screen is displayed.
3) Press the <ENTER> button.
ffThe setting will change between [OFF] and [ON] each time you
press the button.
ffThe [REGISTERED SIGNAL SETUP] screen is displayed.
rr[LOCK]
[OFF]
The signal is not protected.
[ON]
The signal is protected.
Note
ffWhen [LOCK] is set to [ON], signal delete, image adjustment and auto setup are not available. To perform these operations, set [LOCK] to
[OFF].
ffA signal can be registered to sub memory even if it is protected.
ffEven a protected signal will be deleted if [INITIALIZE] is executed.
Expanding signal lock-in range
Signal lock-in range can be expanded.
1) Press asqw to select the signal to set.
4) Press as to select [LOCK-IN RANGE].
2) Press the <ENTER> button.
5) Press qw to switch [LOCK-IN RANGE].
ffThe [REGISTERED SIGNAL STATUS] screen is displayed.
3) Press the <ENTER> button.
ffThe setting will change between [NARROW] and [WIDE] each
time you press the button.
ffThe [REGISTERED SIGNAL SETUP] screen is displayed.
rr[LOCK-IN RANGE]
[NARROW]
[WIDE]
Select in most cases.
Widens the lock-in range.
Note
ffSwitch the range that determines that a signal to be input is the same signal that is already registered.
ffTo prioritize the determination that it is the same signal that is already registered, set to the [WIDE] setting.
ffUse in cases such as when the synchronizing frequency of a signal to be input has changed slightly, or multiple signal lists are registered.
ffCan only be used when a signal is input from the <RGB 1 IN> terminal, <RGB 2 IN> terminal, <DVI-D IN> terminal, or <HDMI IN> terminal.
ffWhen [WIDE] is set, the image may appear distorted because a signal is determined to be the same signal even if a synchronizing
frequency changes slightly.
ffWhen a signal to be input corresponds to the signal set in [WIDE], a registered signal with a high memory number receives priority.
Example: A signal to be input that corresponds to memory numbers A2, A4 and B1 will be determined to be B1.
ffWhen a registration signal is deleted, the settings are also deleted.
ffIn an environment where multiple types of signals are input to the same terminal, signals are sometimes not determined correctly when
settings are set to [WIDE].
Managing the sub memory list
The projector has a sub memory function that can register the multiple image adjustment data, even if it is recognized as the same signal by
the frequency or format of the synchronization signal source.
Use this function when you need to adjust the picture quality such as switching of the aspect ratio or white balance by the same
synchronization signal source. The sub memory includes all the data that can be adjusted for each signal, such as the screen aspect ratio and
data adjusted in the [PICTURE] item ([CONTRAST], [BRIGHTNESS], etc.).
ENGLISH - 87
Chapter 4 Settings — [SIGNAL LIST] menu
To register the current settings to the list
1) Press qw on the normal screen (when the
menu is not displayed).
ffThe sub memory registration screen is displayed if the sub
memory is not registered. Proceed to Step 3).
ffA list of sub memories registered to the signal currently input is
displayed.
ffWhen [SUB MEMORY] is selected with [PROJECTOR SETUP]
→ [FUNCTION BUTTON] on the menu, the <FUNCTION>
button can be used instead of qw.
2) Press asqw to select the sub memory
number to register in [SUB MEMORY LIST].
3) Press the <ENTER> button.
ffThe [SIGNAL NAME CHANGE] screen is displayed.
4) Press asqw to select [OK], and press the
<ENTER> button.
ffTo rename the registered data, follow the procedure in Steps 4)
and 5) in “Renaming the registered data” (x page 86).
To switch to the sub memory list
1) Press qw on the normal screen (when the
menu is not displayed).
ffA list of sub memories registered to the signal currently input is
displayed.
To delete the sub memory data
1) Press qw on the normal screen (when the
menu is not displayed).
ffThe [SUB MEMORY LIST] screen is displayed.
2) Press asqw to select the sub memory to
delete, and press the <DEFAULT> button.
ffThe [ENTRY SIGNAL DELETE] screen is displayed.
ffTo cancel the deletion, press the <MENU> button to return to
the [SUB MEMORY LIST] screen.
3) Press the <ENTER> button.
ffThe selected sub memory will be deleted.
88 - ENGLISH
2) Press asqw to select the signal to switch in
[SUB MEMORY LIST].
3) Press the <ENTER> button.
ffThis switches to the signal selected in Step 2).
Chapter 4 Settings — [SECURITY] menu
[SECURITY] menu
Select [SECURITY] from the main menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” (x page 51) for the operation of the menu screen.
ffWhen the projector is used for the first time
Initial password: Press awsqawsq in order, and press the <ENTER> button.
ffAfter selecting the item, press asqw to set.
Attention
ffWhen you select the [SECURITY] from the main menu and press the <ENTER> button, entering a password is required. Enter the set
password and then continue operations of the [SECURITY] menu.
ffWhen the password has been changed previously, enter the changed password, and press the <ENTER> button.
Note
ffThe entered password is displayed with * mark on the screen.
[SECURITY PASSWORD]
The [SECURITY PASSWORD] screen is displayed when the power is turned on. When the entered password is incorrect, the operation will be
restricted to the power standby <v> button, the <SHUTTER> button, and the <LENS> (<FOCUS>, <ZOOM>, and <SHIFT>) buttons.
1) Press as to select [SECURITY PASSWORD].
2) Press qw to switch [SECURITY PASSWORD].
ffThe setting will change between [OFF] and [ON] each time you
press the button.
rr[SECURITY PASSWORD]
[OFF]
Disables the security password entry.
[ON]
Enables the security password entry.
Note
ffThe [SECURITY PASSWORD] setting is set to [OFF] at the time of purchase or when all the user data has been initialized.
ffChange the password periodically that is hard to guess.
ffThe security password will be enabled after setting [SECURITY PASSWORD] to [ON] and turning the <MAIN POWER> switch to <OFF>.
[SECURITY PASSWORD CHANGE]
Change the security password.
1) Press as to select [SECURITY PASSWORD
CHANGE].
2) Press the <ENTER> button.
ffThe [SECURITY PASSWORD CHANGE] screen is displayed.
3) Press asqw and the number (<0> to <9>)
buttons to set the password.
ffUp to eight button operations can be set.
4) Press the <ENTER> button.
5) Re-enter the password for the confirmation.
6) Press the <ENTER> button.
Note
ffThe entered password is displayed with * mark on the screen.
ffAn error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password.
[DISPLAY SETTING]
Overlap the security message (text or image) over the projecting image.
1) Press as to select [DISPLAY SETTING].
ENGLISH - 89
Chapter 4 Settings — [SECURITY] menu
2) Press qw to switch [DISPLAY SETTING].
ffThe setting will change among [OFF], [TEXT], and[USER
LOGO] each time you press the button.
rr[DISPLAY SETTING]
[OFF]
The text display is disabled.
[TEXT]
The text display is enabled.
[USER LOGO]
The picture registered by the user is projected.
Note
ffTo create the image for [USER LOGO], “Logo Transfer Software” included in the supplied CD-ROM is required.
[TEXT CHANGE]
Change the text displayed when the text display is enabled by selecting [TEXT] in [DISPLAY SETTING].
1) Press as to select [TEXT CHANGE].
2) Press the <ENTER> button.
ffThe [TEXT CHANGE] screen is displayed.
3) Press asqw to select the text, and press the
<ENTER> button to enter the text.
ffMaximum 22 characters can be input.
4) Press asqw to select [OK], and press the
<ENTER> button.
ffThe text is changed.
[MENU LOCK]
Display the menu with the <MENU> button, and set whether to enable menu operations.
1) Press as to select [MENU LOCK].
2) Press qw to switch [MENU LOCK].
ffThe setting will change between [OFF] and [ON] each time you
press the button.
rr[MENU LOCK]
[OFF]
Cancels the lock on menu operations.
[ON]
Locks menu operations.
Note
ffAfter setting [MENU LOCK] to [ON], if the wrong password is input, the <MENU> button cannot be operated.
ffAt the time of purchase or after [ALL USER DATA] initialization, [MENU LOCK] is set to [OFF].
ffThe lock release is maintained until the projector enters standby.
[MENU LOCK PASSWORD]
Change the menu lock password.
1) Press as to select [MENU LOCK
PASSWORD].
2) Press the <ENTER> button.
ffThe [MENU LOCK PASSWORD] screen is displayed.
3) Press asqw to select the text, and press the
<ENTER> button to enter the text.
ffMaximum 16 characters can be input.
4) Press asqw to select [OK] and press the
<ENTER> button.
ffTo cancel, select [CANCEL].
Attention
ffThe initial password when used for the first time or after initializing all the user data is “AAAA”.
ffChange the password periodically that is hard to guess.
[CONTROL DEVICE SETUP]
Enable/disable the button operations on the control panel and the remote control.
1) Press as to select [CONTROL DEVICE
SETUP].
90 - ENGLISH
2) Press the <ENTER> button.
ffThe [CONTROL DEVICE SETUP] screen is displayed.
Chapter 4 Settings — [SECURITY] menu
3) Press as to select [CONTROL PANEL] or
5) Press as to select an item, and press the
4) Press the <ENTER> button.
6) When the confirmation is displayed, select [OK]
[REMOTE CONTROL].
ffThe [CONTROL PANEL] screen or the [REMOTE CONTROL]
screen is displayed.
<ENTER> button.
or [CANCEL], and press the <ENTER> button.
rr[CONTROL PANEL] and [REMOTE CONTROL]
ffYou can set the limitation on the control from the control panel and
remote control.
[ENABLE]
Enables all button operations on the projector body and remote control.
[DISABLE]
Disables all button operations on the projector body and remote control.
Note
ffWhen a button operation is performed on the device set to [DISABLE], the [SECURITY PASSWORD] screen is displayed.
Enter the security password.
ffThe [SECURITY PASSWORD] screen will disappear when the <MENU> button is pressed, or when there is no operation for approximately
ten seconds.
ffIf the operations of both [CONTROL PANEL] and [REMOTE CONTROL] are set to [DISABLE], the projector cannot be turned off (cannot
enter standby).
ffWhen the setting has completed, the menu screen will disappear. To operate continuously, press the <MENU> button to display the main
menu.
ENGLISH - 91
Chapter 4 Settings — [NETWORK] menu
[NETWORK] menu
Select [NETWORK] from the main menu, and select the item from the sub-menu.
Refer to “Navigating through the menu” (x page 51) for the operation of the menu screen.
ffAfter selecting the item, press asqw to set.
[NETWORK SETUP]
Perform the initial setting of the network before using the network function.
1) Press as to select [NETWORK SETUP].
2) Press the <ENTER> button.
ffThe [NETWORK SETUP] screen is displayed.
3) Press as to select an item, and change
4) Press as to select [STORE], and press the
<ENTER> button.
5) When the confirmation is displayed, select [OK]
or [CANCEL], and press the <ENTER> button.
the settings according to the operation
instructions of the menu.
rr[NETWORK SETUP]
[PROJECTOR NAME]
[DHCP]
[IP ADDRESS]
[SUBNET MASK]
[DEFAULT GATEWAY]
[STORE]
Change the setting when using a DHCP server.
Set the item to [ON] when using a DHCP server to automatically acquire the IP address. Set to [OFF] when
not using a DHCP server.
Enter the IP address when not using a DHCP server.
Enter the subnet mask when not using a DHCP server.
Enter the default gateway address when not using a DHCP server.
Save the current network settings.
Note
ffWhen using a DHCP server, confirm that the DHCP server is running.
ffConsult your network administrator regarding the IP address, subnet mask, and default gateway.
[NETWORK CONTROL]
Set up the control method of the network.
1) Press as to select [NETWORK CONTROL].
2) Press the <ENTER> button.
ffThe [NETWORK CONTROL] screen is displayed.
3) Press as to select an item, then press qw to
change the setting.
92 - ENGLISH
4) Press as to select [STORE], and press the
<ENTER> button.
5) When the confirmation is displayed, select [OK]
or [CANCEL], and press the <ENTER> button.
Chapter 4 Settings — [NETWORK] menu
rr[NETWORK CONTROL]
[WEB CONTROL]
[PJLink CONTROL]
[COMMAND CONTROL]
[COMMAND PORT]
[CRESTRON RoomView]
[AMX D.D.]
[STORE]
Set to [ON] to control with the Web browser.
Set to [ON] to control with the PJLink protocol.
Set to [ON] to control with the <SERIAL IN>/<SERIAL OUT> terminal control command format
(x page 123).
Refer to “Control commands via LAN” (x page 119).
Set the port number used for command control.
Set to [ON] to control with RoomView of Crestron.
Set to [ON] to control with the controller of AMX.
Save the current network control settings.
[NETWORK STATUS]
Displays the status of the projector network.
1) Press as to select [NETWORK STATUS].
2) Press the <ENTER> button.
ffThe [NETWORK STATUS] screen is displayed.
Network connections
The projector has a network function, and the following operations are available from the computer using the Web control.
ffSetting and adjustment of the projector
ffDisplay of the projector status
ffSending of E-mail messages when there is a problem with the projector
“Crestron RoomView” is a system of Crestron Electronics, Inc. that manages and controls devices on multiple systems connected to a network
collectively with a computer.
The projector supports the following application software of Crestron Electronics, Inc.
g RoomView Express
g Fusion RV
g RoomView Server Edition
ffFor details of “Crestron RoomView”, refer to the website of Crestron Electronics, Inc. (English only)
URL http://www.crestron.com
For the download of “RoomView Express”, also refer to the website of Crestron Electronics, Inc. (English only)
URL http://www.crestron.com/getroomview
Note
ffA LAN cable is required to use the network function.
&RPSXWHU
3URMHFWRU
/$1FDEOHVWUDLJKW
/$1FDEOHVWUDLJKW
+XE
ffA Web browser is required to use this function. Confirm that the Web browser can be used beforehand.
Compatible OS: Windows XP/Windows Vista/Windows 7, Mac OS X v10.4/v10.5/v10.6/v10.7
Compatible browser: Internet Explorer 7.0/8.0/9.0, Safari 4.0/5.0 (Mac OS)
ffCommunication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be used beforehand.
ffUse a LAN cable that is straight-through and compatible with category 5 or higher.
ffUse a LAN cable of 100 m (328'11") or shorter length.
ENGLISH - 93
Chapter 4 Settings — [NETWORK] menu
Name and function of network function parts
1
2
3
1 LAN10/100 lamp (yellow)
Lights on when connected to the 100BASE-TX.
2 <LAN> terminal (10BASE-T/100BASE-TX)
Used to connect the LAN cable here.
3 LAN LINK/ACT lamp (green)
Lights on when connected.
Flashes when transmitting/receiving data.
Attention
ffConnect the LAN to indoor devices.
Accessing from the Web browser
1) Start up the Web browser on the computer.
2) Enter the IP address set on the projector into
4) Click OK.
ffThe [Projector status] page is displayed.
the URL entry field of the Web browser.
3) Enter the user name and the password.
ffThe factory default setting of the user name is user1 (user
rights)/admin1 (administrator rights) and the password is
panasonic (lower case).
Note
ffIf you use a Web browser to control the projector, set [WEB CONTROL] to [ON] in [NETWORK CONTROL] (x page 92).
ffDo not perform setting or control simultaneously by starting up multiple Web browsers. Do not set or control the projector from multiple
computers.
ffChange the password first. (x page 104)
ffThe administrator rights allows to use all functions. The user rights allow use of [Projector status] (x page 95), confirmation of the error
information page (x page 96), [Network status] (x page 97), [Basic control] (x page 98), and [Change password] (x page 104)
only.
ffAccess will be locked for few minutes when an incorrect password is entered three times consecutively.
94 - ENGLISH
Chapter 4 Settings — [NETWORK] menu
Descriptions of items
(1)
(2)
(3)
(4)
(5)
(6)
1 Page tab
Switches pages by clicking it.
4 [Detailed set up]
The [Detailed set up] page is displayed by clicking this item.
2 [Status]
The status of the projector is displayed by clicking this item.
5 [Change password]
The [Change password] page is displayed by clicking this item.
3 [Projector control]
The [Projector control] page is displayed by clicking this item.
6 [CRESTRON RoomView]
The control page of RoomView is displayed by clicking this item.
[Projector status] page
Click [Status] → [Projector status].
Displays the status of the projector for the following items.
(1)
(6)
(2)
(3)
(7)
(8)
(4)
(5)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
1 [PROJECTOR TYPE]
Displays the type of the projector.
12 [INTAKE AIR TEMPERATURE]
Displays the status of the air intake temperature of the projector.
2 [MAIN VERSION]
Displays the firmware version of the projector.
13 [OPTICS MODULE TEMPERATURE]
Displays the status of the internal temperature of the projector.
3 [POWER]
Displays the status of the power.
14 [AROUND LAMP TEMPERATURE]
Displays the status of the temperature around the lamp of the
projector.
4 [SHUTTER]
Displays the status of the projector.
5 [LAMP SELECT]
Displays the setting status of [LAMP SELECT] (x page 76).
6 [SERIAL NUMBER]
Displays the serial number of the projector.
7 [NETWORK VERSION]
Displays the version of the firmware of the network.
15 [LAMP1][LAMP2][RUNTIME]
Displays the status and the cumulative operating time (converted
value) of the lamp.
16 [SELF TEST]
Displays the self-diagnosis information.
17 [PROJECTOR RUNTIME]
Displays the operation times of the projector.
8 [REMOTE2 STATUS]
Displays the control status of the <REMOTE 2 IN> terminal.
9 [OSD]
Displays the status of the on-screen display.
10 [LAMP POWER]
Displays the setting status of [LAMP POWER] (x page 77).
11 [INPUT]
Displays the status of the input selection.
ENGLISH - 95
Chapter 4 Settings — [NETWORK] menu
Error information page
When [Error (Detail)] is displayed in the self-diagnosis display of the [Projector status] screen, click it to display the error details.
ffThe projector may go into the standby status to protect the projector depending on the contents of the error.
[OK]: operating properly
[FAILED]: a problem occurred
[WARNING]: warning
rrProblem occurrence [FAILED]
Parameter
Description
[MAIN CPU BUS]
There is a problem with the microcomputer circuitry. Consult your dealer.
[FAN]
There is a problem with the fan or the fan drive circuit. Consult your dealer.
[INTAKE AIR TEMPERATURE]
The air intake temperature is too high. It may be used in an operating environment where
the temperature is high, such as near a heating appliance.
[OPTICS MODULE TEMPERATURE]
The temperature inside the projector is high. It may be used in an operating environment
where the temperature is high, such as near a heating appliance.
[AROUND LAMP TEMPERATURE]
The temperature around the lamp is high. The air exhaust port may be blocked.
[LAMP1 REMAIN TIME]
The usage time of the lamp has exceeded the specified time, and it is time to replace the
lamp.
[LAMP2 REMAIN TIME]
[LAMP1 STATUS]
[LAMP2 STATUS]
The lamp has failed to turn on. Wait a while until the luminous lamp cools off, and then
turn on the power.
[SHUTTER]
There is a problem with the shutter circuitry. Consult your dealer.
[INTAKE AIR TEMP.SENSOR]
There is a problem with the sensor used to detect intake air temperature. Consult your
dealer.
[OPTICS MODULE TEMP.SENSOR]
There is a problem with the sensor used to detect temperature inside the projector.
Consult your dealer.
[AROUND LAMP TEMP.SENSOR]
There is a problem with the sensor used to detect exhaust air temperature. Consult your
dealer.
[BATTERY]
Battery replacement is required. Consult your dealer.
[COLOR WHEEL]
There is a problem with the color wheel or the color wheel drive circuit. Consult your
dealer.
[COVER OPEN]
The lamp unit cover is not attached properly. Check the installation of the lamp unit
cover. (x page 114)
[FILTER UNIT]
The air filter unit is not attached. Check the connection of the air filter unit. (x page 113)
[AIR FILTER]
There are too much dust accumulated in the air filter unit.
Turn the <MAIN POWER> switch <OFF> (x page 43), and clean the air filter.
(x page 112)
96 - ENGLISH
Chapter 4 Settings — [NETWORK] menu
[Network status] page
Click [Status] → [Network status].
The current network setting status is displayed.
[Access error log] page
Click [Status] → [Access error log].
The error log on the WEB server is displayed such as access to the pages that do not exist or access with unauthorized user names or
passwords.
[Access log] page
Click [Status] → [Access log].
The log such as user name accessed to the WEB control page, accessed IP address, and accessed time is displayed.
Note
ff[Access error log]/[Access log] will display the recent few thousand accesses/requests. May be unable to display all information when many
accesses/requests are made at one time.
ffWhen [Access error log]/[Access log] exceeds a certain amount, old information will be erased.
ffConfirm [Access error log]/[Access log] periodically.
ENGLISH - 97
Chapter 4 Settings — [NETWORK] menu
[Basic control] page
Click [Projector control] → [Basic control].
(1)
(2)
(3)
(4)
(5)
(6)
1 [POWER]
Switches the power on/off.
4 [SYSTEM]
Switches the system method.
2 [SHUTTER]
Switches between use or not use of the shutter function.
5 On-screen display of the projector
Displays the same content as the on-screen display of the
projector. The settings of the menu can be checked or changed.
This is displayed even when the on-screen display function is
set to off (hide).
3 [OSD]
Switches between on (display)/off (no display) of the on-screen
display function.
6 [INPUT SELECT]
Switches the input signal.
[Detail control] page
Click [Projector control] → [Detail control].
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
1 Control of the projector
The projector is controlled by clicking the buttons in the same
way as the buttons on the remote control. After the projector is
controlled, the on-screen display of the projector on the right
side of the control page is updated.
4 [GET OSD]
Updates the on-screen display of the projector at the right of the
control page.
2 [LENS]
Adjusts the projection lens.
6 [SYSTEM DAYLIGHT VIEW]
Switches to system daylight view settings.
3 [TEST PATTERN]
Displays the test pattern.
5 [SUB MEMORY]
Switches the sub memory.
7 [FREEZE]
Temporarily pauses the image.
8 [SIDE BY SIDE] (only for PT-DW740E)
Displays two different input signals simultaneously.
[Network config] page
Click [Detailed set up] → [Network config].
ffClick [Network config] to display the [CAUTION!] screen.
ffThe current settings are displayed by pressing the [Next] button.
98 - ENGLISH
Chapter 4 Settings — [NETWORK] menu
ffThe following setting change screen is displayed by pressing the [Change] button.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
1 [PROJECTOR NAME]
Enter the name of the projector. Also enter the host name if it is
required when using a DHCP server, etc.
2 [DHCP ON]/[DHCP OFF]
To enable the DHCP client function, set to [DHCP ON].
3 [IP ADDRESS]
Enter the IP address when not using a DHCP server.
4 [SUBNET MASK]
Enter the subnet mask when not using a DHCP server.
5 [DEFAULT GATEWAY]
Enter the default gateway address when not using a DHCP
server.
6 [DNS1]
Enter the DNS1 server address.
Permissible characters for the entry of DNS1 server address
(primary):
Numbers (0 to 9), period (.)
(Example: 192.168.0.253)
7 [DNS2]
Enter the DNS2 server address.
Permissible characters for the entry of DNS2 server address
(secondary):
Numbers (0 to 9), period (.)
(Example: 192.168.0.254)
8 [Back]/[Next]
Click the [Back] button to return to the original screen. The
current settings are displayed by pressing the [Next] button.
Click the [Submit] button to update the settings.
Note
ffWhen you use the “Forward” and “Back” functions of your browser, a warning message “Page has Expired” may appear. In that case, click
[Network config] again since the following operation will not be guaranteed.
[Adjust clock] page
Click [Detailed set up] → [Adjust clock].
(1)
(2)
(3)
(4)
(5)
(6)
(7)
1 [Time Zone]
Select the time zone.
5 [Date]
Enter the date to be changed.
2 [Set time zone]
Updates the time zone setting.
6 [Time]
Enter the time to be changed.
3 [NTP SYNCHRONIZATION]
Set to [ON] to adjust the date and time automatically.
7 [Set date and time]
Updates the date and time settings.
4 [NTP SERVER NAME]
Enter the IP address or server name of the NTP server when
you set to adjust the date and time manually.
(To enter the server name, the setup of the DNS server is
required.)
ENGLISH - 99
Chapter 4 Settings — [NETWORK] menu
Note
ffThe replacement of the battery inside the projector is required when the time goes out of alignment right after correcting the time. Please
consult your dealer.
[Ping test] page
You can check whether the network is connected to the E-mail server, POP server, DNS server, etc.
Click [Detailed set up] → [Ping test].
(1)
(2)
(3)
(4)
1 [Input IP address]
Enter the IP address of the server to be tested.
2 [Submit]
Executes the connection test.
100 - ENGLISH
3 Example of display when the connection has succeeded
4 Example of display when the connection has failed
Chapter 4 Settings — [NETWORK] menu
[E-mail set up] page
You can send E-mail to an E-mail address (maximum two addresses) set in advance when a problem occurs or the cumulative operating time
of a lamp reaches a set value.
Click [Detailed set up] → [E-mail set up].
(1)
(2)
(3)
(4)
(5)
(6)
1 [ENABLE]
Select [Enable] to use the E-mail function.
2 [SMTP SERVER NAME]
Enter the IP address or the server name of the E-mail server
(SMTP). To enter the server name, the setup of the DNS server
is required.
3 [MAIL FROM]
Enter the E-mail address of the projector. (Up to 63 characters
in single byte)
4 [MEMO]
You can enter information such as the location of the projector
that notifies the sender of the E-mail. (Up to 63 characters in
single byte)
5 [MINIMUM TIME]
Change the minimum interval for the temperature warning mail.
The default value is 60 minutes. In this case, another E-mail
will not be sent for 60 minutes after sending the temperature
warning mail even if it reaches the warning temperature.
6 [INTAKE AIR TEMPERATURE]
Change the temperature setting for the temperature warning
mail. A temperature warning mail is sent when the temperature
exceeds this value.
(7)
(8)
7 [E-MAIL ADDRESS 1]
Enter the E-mail address to be sent.
8 Settings of the conditions to send E-mail
Select the conditions to send E-mail.
[MAIL CONTENTS]:
Select either [NORMAL] or [SIMPLE].
[ERROR]:
An E-mail message is sent when an error occurred in the selfdiagnosis.
[LAMP1 RUNTIME]:
An E-mail message is sent when the remaining lamp on time for
the lamp 1 has reached the value set at the right field.
[LAMP2 RUNTIME]:
An E-mail message is sent when the remaining lamp on time for
the lamp 2 has reached the value set at the right field.
[INTAKE AIR TEMPERATURE]:
An E-mail message is sent when the air intake temperature has
reached the value set at the above field.
[PERIODIC REPORT]:
Place a check mark on this when E-mail is to be sent
periodically.
It will be sent on the days and time with the check mark.
ENGLISH - 101
Chapter 4 Settings — [NETWORK] menu
(9)
(10)
(11)
9 [E-MAIL ADDRESS 2]
Enter the E-mail address to be sent when two E-mail addresses
are to be used.
Leave it blank when two E-mail addresses are not to be used.
10 Settings of the conditions to send E-mail
Select the conditions to send E-mail to the second E-mail
address.
[MAIL CONTENTS]:
Select either [NORMAL] or [SIMPLE].
[ERROR]:
An E-mail message is sent when an error occurred in the selfdiagnosis.
[LAMP1 RUNTIME]:
An E-mail message is sent when the remaining lamp on time for
the lamp 1 has reached the value set at the right field.
[LAMP2 RUNTIME]:
An E-mail message is sent when the remaining lamp on time for
the lamp 2 has reached the value set at the right field.
[INTAKE AIR TEMPERATURE]:
An E-mail message is sent when the air intake temperature has
reached the value set at the above field.
[PERIODIC REPORT]:
Place a check mark on this to send E-mail to the second E-mail
address periodically. It will be sent on the days and time with the
check mark.
11 [Submit]
Update the settings.
[Authentication set up] page
You can set the authentication items when POP authentication or SMTP authentication is necessary to send an E-mail message.
Click [Detailed set up] → [Authentication set up].
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
1 [Auth]
Select the authentication method specified by your Internet
service provider.
7 [POP server port]
Enter the port number of the POP server.
(Normally 110)
2 [SMTP Auth]
Set when the SMTP authentication is selected.
8 [Submit]
Update the settings.
3 [POP server name]
Enter the POP server name.
Allowed characters:
Alphanumerics (A to Z, a to z, 0 to 9)
Minus sign (-) and period (.)
4 [User name]
Enter the user name for the POP server or the SMTP server.
5 [Password]
Enter the password for the POP server or the SMTP server.
6 [SMTP server port]
Enter the port number of the SMTP server.
(Normally 25)
102 - ENGLISH
Chapter 4 Settings — [NETWORK] menu
Contents of mail sent
Example of E-mail sent when E-mail is set
The following E-mail is sent when the E-mail settings have been established.
=== Panasonic projector report(CONFIGURE) ===
Projector Type
: DW740
Serial No
: SH1234567
----- E-mail setup data ----TEMPERATURE WARNING SETUP
MINIMUM TIME
at [ 60] minutes interval
INTAKE AIR TEMPERATURE Over [ 45C / 113F ]
ERROR
[ OFF ]
LAMP1 RUNTIME
[ OFF ] at REMAIN [ 400] H
LAMP1 RUNTIME
[ OFF ] at REMAIN [ 200] H
LAMP2 RUNTIME
[ OFF ] at REMAIN [ 400] H
LAMP2 RUNTIME
[ OFF ] at REMAIN [ 200] H
INTAKE AIR TEMPERATURE [ OFF ]
PERIODIC REPORT
Sunday [ OFF ] Monday [ OFF ] Tuesday [ OFF ] Wednesday [ OFF ]
Thursday [ OFF ] Friday [ OFF ] Saturday [ OFF ]
00:00
04:00
08:00
12:00
16:00
20:00
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
01:00
05:00
09:00
13:00
17:00
21:00
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
02:00
06:00
10:00
14:00
18:00
22:00
----- check system ----MAIN CPU BUS
[
FAN
[
INTAKE AIR TEMPERATURE
[
OPTICS MODULE TEMPERATURE [
AROUND LAMP TEMPERATURE [
LAMP1 REMAIN TIME
[
LAMP2 REMAIN TIME
[
LAMP1 STATUS
[
LAMP2 STATUS
[
SHUTTER
[
INTAKE AIR TEMP.SENSOR
[
OPTICS MODULE TEMP.SENSOR [
AROUND LAMP TEMP.SENSOR
[
BATTERY
[
COLOR WHEEL
[
COVER OPEN
[
FILTER UNIT
[
AIR FILTER
[
(Error code 00 00 00 00 00 00 00 00)
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
03:00
07:00
11:00
15:00
19:00
23:00
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
[ OFF ]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
]
Intake air temperature : 26 degC / 78 degF
Optics module temperature : 39 degC / 102 degF
Around lamp temperature : 30 degC / 86 degF
PROJECTOR RUNTIME 1 H
POWER ON
1 times
LAMP1 ON
1 times
LAMP1 ECO
0H
LAMP1 NORMAL
0H
LAMP1 REMAIN
1999 H
LAMP2 ON
1 times
LAMP2 ECO
0H
LAMP2 NORMAL
1H
LAMP2 REMAIN
1999 H
-------- Current status --------MAIN VERSION
1.00
NETWORK VERSION
1.00
SUB VERSION
1.00
LAMP STATUS
LAMP1=ON LAMP2=ON
INPUT SIGNAL
RGB1 --0.00kHz / 0.00Hz
REMOTE2 STATUS
DISABLE
----- Wired Network configuration ----DHCP Client OFF
IP address 192.168.10.100
MAC address 70:58:12:00:00:00
Wed Jan 18 11:42:37 2012
----- Memo -----
ENGLISH - 103
Chapter 4 Settings — [NETWORK] menu
Example of the E-mail sent for an error
The following E-mail is sent when an error has occurred.
=== Panasonic projector report(CONFIGURE) ===
Projector Type
: DW740
Serial No
: SH1234567
----- check system ----MAIN CPU BUS
[ OK ]
FAN
[ OK ]
INTAKE AIR TEMPERATURE
[ OK ]
OPTICS MODULE TEMPERATURE [ OK ]
AROUND LAMP TEMPERATURE
[ OK ]
LAMP1 REMAIN TIME
[ OK ]
LAMP2 REMAIN TIME
[ OK ]
LAMP1 STATUS
[ OK ]
LAMP2 STATUS
[ OK ]
SHUTTER
[ OK ]
INTAKE AIR TEMP.SENSOR
[ OK ]
OPTICS MODULE TEMP.SENSOR [ OK ]
AROUND LAMP TEMP.SENSOR
[ OK ]
BATTERY
[ OK ]
COLOR WHEEL
[ OK ]
COVER OPEN
[ OK ]
FILTER UNIT
[ FAILED ]
AIR FILTER
[ OK ]
(Error code 04 00 00 00 00 00 00 00)
Intake air temperature : 26 degC / 78 degF
Optics module temperature : 39 degC / 102 degF
Around lamp temperature : 30 degC / 86 degF
PROJECTOR RUNTIME 1 H
POWER ON
1 times
LAMP1 ON
1 times
LAMP1 ECO
0H
LAMP1 NORMAL
0H
LAMP1 REMAIN
1999 H
LAMP2 ON
1 times
LAMP2 ECO
0H
LAMP2 NORMAL
1H
LAMP2 REMAIN
1999 H
-------- Current status --------MAIN VERSION
1.00
NETWORK VERSION
1.00
SUB VERSION
1.00
LAMP STATUS
LAMP1=ON LAMP2=ON
INPUT SIGNAL
RGB1 --0.00kHz / 0.00Hz
REMOTE2 STATUS
DISABLE
----- Wired Network configuration ----DHCP Client OFF
IP address 192.168.10.100
MAC address 70:58:12:00:00:00
Wed Jan 18 11:42:37 2012
----- Memo -----
User name [Change password] page
Click [Change password].
1
2
3
1 [Administrator]
Used to change the setting of the [Administrator].
2 [User]
Used to change the setting of the [User].
3 [Next]
Used to change the setting of the password.
104 - ENGLISH
Chapter 4 Settings — [NETWORK] menu
[Administrator] account
(1)
(2)
(3)
(4)
(5)
(6)
(7)
1 [Account]
Displays the account to change.
2 [Current][User name]
Enter the user name before the change.
3 [Current][Password]
Enter the current password.
4 [New][User name]
Enter the desired new user name. (Up to 16 characters in single
byte)
5 [New][Password]
Enter the desired new password. (Up to 16 characters in single
byte)
6 [New][Password(Retype)]
Enter the desired new password again.
7 [OK]
Determines the change of password.
[User] account
(1)
(2)
(3)
(4)
(5)
1 [Account]
Displays the account to change.
2 [New][User name]
Enter the desired new user name. (Up to 16 characters in single
byte)
3 [New][Password]
Enter the desired new password. (Up to 16 characters in single
byte)
4 [New][Password(Retype)]
Enter the desired new password again.
5 [OK]
Determines the change of password.
ENGLISH - 105
Chapter 4 Settings — [NETWORK] menu
[Change password] (For user rights)
Only the change of password is enabled under the user rights.
(1)
(2)
(3)
(4)
1 [Old Password]
Enter the current password.
3 [Retype]
Enter the desired new password again.
2 [New Password]
Enter the desired new password. (Up to 16 characters in single
byte)
4 [OK]
Determines the change of password.
Note
ffTo change the account of the administrator, you must enter the [Current] [User name] and [Password].
[CRESTRON RoomView] page
The projector can be monitored and/or controlled with RoomView.
To start the RoomView control page from the Web control screen, you need to access with the administrator rights. (For user rights, the
[CRESTRON RoomView] button is not displayed on the Web control screen.)
The control page of RoomView is displayed by clicking [CRESTRON RoomView].
It is not displayed if Adobe Flash Player is not installed on the computer used, or the browser used does not support Flash. In that case, click
[Back] on the control page to go back to the previous page.
Control page
1
2
3
4
5
6
7
1 [Tools][Info][Help]
Tabs for selecting the setting, information, or help page of the
projector.
2 [POWER]
Switches the power on/off.
3 [SHUTTER]
Switches between use or not use of the shutter function.
4 [Input Select]
Controls input selection.
Not available when the power of the projector is turned off.
5 Menu screen control buttons
Navigates the menu screen.
106 - ENGLISH
6 Freeze/Picture quality adjustment
Controls items related to freeze/picture quality.
7 [Back]
Performs return to the previous page.
Chapter 4 Settings — [NETWORK] menu
[Tools] page
Click [Tools] on the control page.
1
2
3
4
5
1 [Control System]
Set the information required for communicating with the
controller to be connected with the projector.
2 [User Password]
Set the user rights password for the RoomView control page.
3 [Admin Password]
Set the administrator rights password for the RoomView control
page.
4 Network Status
Displays the settings of wired LAN.
[DHCP]
Displays the current setting.
[Ip Address]
Displays the current setting.
[Subnet Mask]
Displays the current setting.
[Default Gateway]
Displays the current setting.
[DNS Server]
Displays the current setting.
5 [Exit]
Returns to the control page.
[Info] page
Click [Info] on the control page.
1
4
5
2
3
6
7
8
1 [Projector Name]
Displays the projector name.
2 [Mac Address]
Displays the MAC address.
3 [Lamp Hours]
Displays the cumulative operating time (converted value) of the
lamps.
4 [Power Status]
Displays the status of the power.
5 [Source]
Displays the selected image input.
6 [Lamp Mode]
Displays the lamp mode.
7 [Error Status]
Displays the error status.
8 [Exit]
Returns to the control page.
ENGLISH - 107
Chapter 4 Settings — [NETWORK] menu
[Help] page
Click [Help] on the control page.
The [Help Desk] window is displayed.
1
1 [Help Desk]
Messages can be sent to or received from an administrator who
uses Crestron RoomView.
108 - ENGLISH
Chapter 5
Maintenance
This chapter describes inspection when there are problems, and maintenance methods.
ENGLISH - 109
Chapter 5 Maintenance — Lamp/Temperature/Filter indicators
Lamp/Temperature/Filter indicators
Managing the indicated problems
If a problem should occur inside the projector, the lamp indicators <LAMP1>/<LAMP2>/ the temperature indicator <TEMP> and the filter
indicator <FILTER> will inform you by lighting or flashing.
Check the status of the indicators and manage the indicated problems as follows.
Attention
ffWhen switching off the projector to deal with problems, make sure to follow the procedure in “Switching off the projector” (x page 43).
ffCheck the status of the power supply with the power indicator <ON (G)/STANDBY (R)> (x page 42).
Lamp indicator <LAMP1>
Power indicator <ON (G)/STANDBY (R)>
Lamp indicator <LAMP2>
Temperature indicator <TEMP>
Filter indicator <FILTER>
Lamp indicators <LAMP1>/<LAMP2>
Indicator status
Lighting in red
Flashing in red
(1 time)
Flashing in red
(3 times)
Status
Time to replace the lamp
unit.
The lamp unit is not
attached.
A problem is detected in the lamp or the power supply for
the lamp.
ffIs the lamp unit attached?
ffHave you turned on the
power again immediately
after turning it off?
Cause
ffWas [REPLACE LAMP]
displayed when you
turned on the power of the
projector?
ffThis indicator lights up
when the cumulative
operating time of the
lamp unit has reached
1 800 hours (when
[LAMP POWER] is set to
[NORMAL]).
ffReplace the lamp unit.
ffInstall the lamp case if the
lamp unit is not installed.
ffIf the indicator is still
blinking in red even
though the lamp unit is
not installed, consult your
dealer.
ffWait a while until the
ffTurn the <MAIN
luminous lamp cools off,
POWER> switch
and then turn on the power. <OFF>(x page 43), and
consult your dealer.
Solution
ffSome error has arisen in
the lamp circuit. Check for
fluctuation (or drop) in the
source voltage.
Note
ffIf lamp indicator <LAMP1>/<LAMP2> is still lit or flashing after the preceding measures are taken, ask your dealer to repair the unit.
110 - ENGLISH
Chapter 5 Maintenance — Lamp/Temperature/Filter indicators
Temperature indicator <TEMP>
Indicator status
Flashing in red
(1 time)
Flashing in red
(3 times)
Internal temperature is high
(standby warning)
The cooling fan has stopped.
Lighting in red
Status
Warm-up status
Internal temperature is high
(warning)
Cause
ffDid you turn on the
power when the room
temperature was about
0°C (32°F)?
ffIs the air intake/exhaust port blocked?
ffIs the room temperature high?
ffIs the filter indicator <FILTER> not lit?
ffWait at least five minutes
in the current status.
ffInstall the unit in a
location with an ambient
temperature of 0°C (32°F)
to 45°C (113°F)*.
ffRemove any objects that are blocking the air intake/
exhaust port.
ffSet up the projector in a location with an ambient
temperature of 0°C (32°F) to 45°C (113°F)*, and a
humidity of 20% to 80% (no condensation).
ffClean the air filter unit or replace it. (x pages 112, 113)
Solution
―
ffTurn the <MAIN
POWER> switch
<OFF>(x page 43), and
consult your dealer.
*When using the projector at high altitudes (1 400 m (4 593 ft) – 2 700 m (8 858 ft) above sea level), the operating environment temperature will be 5°C
(41°F) lower than the maximum limit.
Note
ffIf the temperature indicator <TEMP> is still lit or flashing after taking the preceding measures, ask your dealer to repair the unit.
ffIf the projector is used with the next two items set and the ambient temperature becomes 40°C (104°F) (35°C (95°F) in [HIGH ALTITUDE
MODE]) or higher, light output may decrease 20% to protect the projector.
ggWhen [LAMP SELECT] is set to [DUAL] on the menu
ggWhen [LAMP POWER] is set to [NORMAL] on the menu
Filter indicator <FILTER>
Indicator status
Status
Cause
Solution
Lighting in red
Flashing in red
The filter is clogged.
The temperature inside or outside the projector is abnormally high.
The air filter unit is not
attached.
ffIs the air filter unit dirty?
ffIs the air intake/exhaust
port blocked?
ffIs [HIGH ALTITUDE
MODE] set correctly?
ffIs the air filter unit
attached?
ffClean the air filter unit or
replace it. (x pages 112,
113)
ffRemove any objects that
are blocking the air intake/
exhaust port.
ffWhen using the projector
at elevations 1 400 m
(4 593 ft) – 2 700 m
(8 858 ft) above sea level,
set [HIGH ALTITUDE
MODE] (x page 76) to
[ON].
ffDo not use the projector
at high elevations 2 700 m
(8 858 ft) or higher above
sea level.
ffAttach the air filter unit.
Note
ff If the filter indicator <FILTER> is still lit or flashing after taking the preceding measures, ask your dealer to repair the unit.
ffIf the air filter unit is not installed when the power is turned on, the filter indicator <FILTER> will flash in red and the power will switch off 10
minutes later.
ffIf the filter is clogged, only one lamp may light even when [LAMP SELECT] is set to [DUAL]. Cleaning the air filter unit or replacing it with a
new one will turn off the indicator.
ENGLISH - 111
Chapter 5 Maintenance — Maintenance/replacement
Maintenance/replacement
Before maintaining/replacing the unit
ffMake sure to turn off the power before maintaining or replacing the unit. (x pages 41, 43)
ffWhen switching off the projector, make sure to follow the procedures in “Switching off the projector” (x page 43).
Maintenance
Outer case
Wipe off dirt and dust with a soft, dry cloth.
ffIf the dirt is persistent, soak the cloth with water and wring it thoroughly before wiping. Dry off the projector with a dry cloth.
ffDo not use benzene, thinner, rubbing alcohol, other solvents, or household cleaners. Doing so may deteriorate the outer case.
ffWhen using chemically treated dust cloths, follow the instructions written on its packaging.
Front surface of the lens
Wipe off dirt and dust from the front surface of the lens with a soft clean cloth.
ffDo not use a cloth that is fluffy, dusty, or soaked with oil/water.
ffSince the lens is fragile, do not use excessive force when wiping the lens.
Attention
ffThe lens is made of glass. Impacts or excessive force when wiping may scratch its surface. Please handle with care.
Air filter unit
Perform maintenance of the air filter unit in the following cases.
ffThe air filter is clogged with dust, causing the filter replacement message to appear on the screen and the filter indicator <FILTER> to light in
red.
Pulling out the air filter unit
1) Remove the air filter cover.
ffUse a Phillips screwdriver to turn the air filter cover screw
counterclockwise until it turns freely, and then remove the air
filter cover.
2) Pull out the air filter unit.
ffGrasp the air filter unit tabs and remove the air filter unit from
the projector body.
Air filter cover
Air filter unit
Tabs
72
Air filter cover fixing screw
Attention
ff After pulling out the air filter unit, remove any large foreign objects or dust present in the air filter unit compartment and the air intake port of
the projector body.
Cleaning the air filter unit
First pull out the air filter in the procedure described in “Pulling out the air filter unit”.
1) Clean the air filter unit.
i)
Soak the air filter unit in cold or warm water and then lightly
rinse it.
ggDo not use cleaning tools such as brushes.
ggWhen rinsing, hold the frame of the air filter unit without
putting strong pressure on the filter unit.
ii)
Rinse the unit two to three times using fresh water each time.
ggInsufficient rinsing may result in odors.
112 - ENGLISH
Chapter 5 Maintenance — Maintenance/replacement
2) Dry the air filter unit.
ffLet the unit naturally dry off in a well-ventilated place where
there is little dust and the unit is protected from direct sunlight.
ffDo not dry using drying devices such as dryers.
ffWhen the air filter unit is dry, proceed to the procedure
described in “Attaching the air filter unit” (x page 113).
Attaching the air filter unit
1) Attach the air filter unit to the projector.
ffThe top and bottom of the air filter unit are different.
(Make sure of the direction of the arrow (L).)
ffAttach in reverse order of Step 2) in “Pulling out the air filter
unit” (x page 112).
2) Attach the air filter cover to the projector and
use a Phillips screwdriver to tighten the air
filter cover screw.
ffAttach in reverse order of Step 1) in “Pulling out the air filter
unit” (x page 112).
Attention
ff After washing the air filter unit, dry it thoroughly before attaching it back to the projector. Attaching a wet unit will cause an electric shock or
malfunction.
ff Do not disassemble the air filter unit.
Note
ff Make sure that the air filter unit is properly attached before using the projector. If not properly attached, the projector will suck in dirt and
dust which causes malfunction and the power to switch off 10 minutes later. (The time remaining until the power switches off is displayed in
1-minute increments.)
ff Replace the air filter unit with a replacement filter unit (ET-EMF300) if it is damaged or if the dirt does not come off even after washing.
ff Air filter replacement is recommended after cleaning the unit two times.
ff The dust-proof properties may be reduced after each cleaning.
Replacing the unit
Air filter unit
If dirt does not come off even if the unit is maintained, it is time for the unit to be replaced.
The replacement filter unit (Model No.: ET-EMF300) is an optional accessory. To purchase the product, consult your dealer.
Replacing the air filter unit
Attention
ff Make sure to turn off the power before replacing the air filter unit.
ff When replacing the unit, make sure that the projector is stable. Perform the replacement in a safe place where the projector will not be
damaged even if you drop the air filter unit.
1) Pull out the air filter unit.
ffRefer to “Pulling out the air filter unit” (x page 112).
2) Attach the replacement filter unit optional
accessory (Model No.: ET-EMF300) to the
projector body.
ffThe top and bottom of the air filter unit are different. (Make sure
of the direction of the arrow (L).)
ffRefer to “Attaching the air filter unit” (x page 113).
Attention
ff When switching on the projector, make sure that the air filter unit is installed. If not properly attached, the projector will suck in dirt and dust
which causes malfunction and the power to switch off 10 minutes later. (The time remaining until the power switches off is displayed in
1-minute increments.)
ENGLISH - 113
Chapter 5 Maintenance — Maintenance/replacement
Note
ff The replacement cycle of the air filter unit varies greatly depending on the usage environment.
Lamp unit
The lamp unit is a consumable component. Check the lamp usage time in [PROJECTOR SETUP] [STATUS] (x page 81) in the menu and
change the lamp periodically.
It is recommended that you request a qualified technician to replace the lamp unit. Consult your dealer.
Consult your dealer to purchase a replacement lamp unit (Model No.: ET-LAD60A (1 bulb), ET-LAD60AW (2 bulbs)).
Warning
ffReplace the lamp unit after the lamp has cooled (after waiting at least one hour).
The high internal temperature of the cover will cause burns.
Notes on the replacement of the lamp unit
ffSince the luminous lamp is made of glass, it may burst if dropped or hit with a hard object.
Please handle with care.
ffA Phillips screwdriver is necessary when replacing the lamp unit.
ffMake sure you hold the lamp unit by its handles during replacement.
ffThe lamp may burst. Replace the lamp unit carefully so that the broken pieces of the lamp glass will not scatter. If the projector is mounted
to the ceiling, do not make the replacement directly beneath the lamp unit or put your face near it.
ffThe lamp contains mercury. When disposing of used lamp units, contact your local authorities or dealer for correct methods of disposal.
Attention
ffUse only specified lamp units.
Note
ffThe model numbers of accessories and optional components are subject to change without notice.
When to replace the lamp unit
The lamp unit is a consumable component. Since its brightness gradually decreases over time, it is necessary to replace it regularly. The
estimated duration before replacement is 2 000 hours. However, this may be shortened depending on individual lamp characteristics, usage
conditions, and the installation environment. Therefore, it is strongly recommended that a replacement lamp unit be prepared. If the lamp is not
replaced after 2 000 hours of use, a malfunction will occur and the projector will automatically switch off after approximately ten minutes.
On-screen display
Lamp indicator
REPLACE LAMP
Over 1 800 hours
The message is displayed for 30 seconds. Pressing
any button on the control panel or remote control
within 30 seconds will clear the message.
Over 2 000 hours
The message remains displayed until you press a
button.
Lights in red even during the standby mode.
(Only the corresponding lamp lights)
Note
ffThe 2 000 hour usage period is a rough estimate and is not guaranteed.
Replacing the lamp unit
Attention
ffWhen the projector is mounted on the ceiling, do not perform tasks while your face is near the lamp unit.
ffMake sure to attach the lamp unit and lamp unit cover properly.
ffIf the lamp unit is not installed properly, remove it and then attach it again. Pushing it in forcibly may break the connector.
114 - ENGLISH
Chapter 5 Maintenance — Maintenance/replacement
1) Follow the procedures described in “Switching
off the projector” (x page 43) to set the
<MAIN POWER> switch to <OFF>, disconnect
the power plug from the power outlet, and wait
at least one hour, and then check if the lamp
unit has cooled down.
2) Remove the lamp unit cover.
i)
Use a Phillips screwdriver to loosen the lamp unit cover fixing
screw (one screw) until it turns freely, and then open the lamp
unit cover in the direction of the arrow.
ii)
Hold the lamp unit cover securely and slide it towards the
control button side, and then pull it from the rear of the set to
remove.
4) Carefully push the new lamp unit into the
projector.
5) Use a Phillips screwdriver to firmly tighten the
lamp unit fixing screws (three screws each).
6) Attach the lamp unit cover.
i)
Attach the lamp unit cover while aligning the (a) and (b) marks
(E and A).
ii)
Slide the lamp unit cover in the direction of the arrow to insert
the front end and then firmly tighten the lamp unit cover fixing
screws.
ffAttach so that the connector of the lamp unit cover is firmly
inserted into the fan power supply connector.
Lamp unit cover
(a)
(i)
(b)
Fan power supply connector
(i)
Lamp unit cover
fixing screw
(ii)
3) Use a Philips screwdriver to remove the lamp
unit fixing screws (three screws each), and
then holding the handles, pull out the lamp
unit from the projector.
+DQGOHV
/DPSXQLW
Lamp unit cover
fixing screw
(ii)
Lamp unit cover
/DPSXQLW
/DPSXQLWIL[LQJVFUHZV
Note
ff When you place the new lamp unit, the projector resets the total usage time of the lamp unit automatically.
ENGLISH - 115
Chapter 5 Maintenance — Troubleshooting
Troubleshooting
Review the following points. For details, see the corresponding pages.
Problems
Power does not turn on.
Points to be checked
ffIs the power plug firmly inserted into the outlet?
―
ffIs the <MAIN POWER> switch turned <OFF>?
43
ffIs the wall outlet supplying electricity?
―
ffHave the circuit breakers tripped?
ffIs the temperature indicator <TEMP> or the lamp indicator <LAMP1>/<LAMP2> lit or flashing?
ffIs the lamp unit cover securely installed?
ffAre connections to external devices correctly performed?
ffIs the input selection setting correct?
No image appears.
The picture is fuzzy.
―
110, 111
114
37
48, 79
ffIs the [BRIGHTNESS] adjustment setting at a minimum?
55
ffIs the external device that is connected to the projector working properly?
―
ffIs the shutter function in use?
47
ffIf the power indicator <ON (G)/STANDBY (R)> is flashing in red, consult your dealer.
―
ffIs the lens focus set correctly?
45
ffIs the projection distance appropriate?
27
ffIs the lens dirty?
16
ffIs the projector installed perpendicular to the screen?
―
ffIs the [COLOR] or [TINT] adjusted correctly?
56
The color is pale or grayish. ffIs the external device connected to the projector adjusted correctly?
ffIs the RGB cable damaged?
The remote control does
not respond.
Page
37
―
ffAre the batteries depleted?
―
ffIs the polarity of the batteries set correctly?
23
ffAre there any obstructions between the remote control and the projector’s remote control
signal receiver?
20
ffIs the remote control being used beyond its effective operation range?
20
ffAre other forms of light, such as fluorescent light, affecting the projection?
20
ffIs the [REMOTE CONTROL] setting in [CONTROL DEVICE SETUP] set to [DISABLE]?
90
ffIs the <REMOTE 2 IN> terminal used for contact control?
124
ffIs the ID number setting operation correct?
23
The menu screen does not
appear.
ffIs the on-screen display function turned off (hidden)?
The buttons on the control
panel do not operate.
ffIs the [CONTROL PANEL] setting in [CONTROL DEVICE SETUP] set to [DISABLE]?
90
ffIs the <REMOTE 2 IN> terminal used for contact control?
124
ffIs the [SYSTEM SELECTOR] selection set correctly?
59
The image does not display
ffIs there a problem with the video tape or other image sources?
correctly.
ffIs a signal which is not compatible with the projector being input?
22, 47
―
125
ffIs the cable too long? (Use D-Sub cables that are 10 m (32'10") or shorter.)
―
Image from a computer
does not appear.
ffIs the external video output of the laptop computer set correctly? Ex.: The external output
settings may be switched by pressing the “Fn”+“F3” or “Fn”+“F10” keys simultaneously. Since
the method varies depending on the computer type, refer to the user manual provided with
your computer.)
―
Image from a computer’s
DVI-D output does not
appear.
ffIs the [DVI-D IN] setting set to [EDID3]/[EDID2:PC]?
70
ffThe graphics accelerator driver of the computer may need to be updated to the latest version.
―
ffThe computer may need to be restarted after performing [DVI-D IN] settings.
70
Video from HDMI
compatible device does
not appear or it appears
jumbled.
ffIs the HDMI cable connected securely?
37
ffTurn the power of the projector and the external device on and off.
―
ffIs a signal which is not compatible with the projector being input?
125
Attention
ff If problems persist even after checking the preceding points, consult your dealer.
116 - ENGLISH
Chapter 6
Appendix
This chapter describes specifications and after-sales service for the projector.
ENGLISH - 117
Chapter 6 Appendix — Technical information
Technical information
PJLink protocol
The network function of this projector supports the PJLink class 1, and the PJLink protocol can be used to perform projector setting and
projector status query operations from a computer.
Control commands
The following table lists the PJLink protocol commands that can be used to control the projector.
Command
Control details
Notes
Power supply control
Parameters
0 = Standby
1 = Power on
POWR?
Power supply status query
Parameters
0 = Standby
1 = Power on
2 = Cool-down in progress
3 = Warm-up in progress
INPT
Input selection
INPT?
Input selection query
AVMT
Shutter control
AVMT?
Shutter status query
POWR
Parameters
11=RGB1
12=RGB2
21=VIDEO
22=S-VIDEO
31=DVI-D
32=HDMI
Parameters
30 = shutter function off (picture mute canceled)
31 = shutter function on (picture mute)
Error status query
Parameters
1st byte: Indicates fan errors, range 0 - 2
2nd byte: Indicates lamp errors, range 0 - 2
3rd byte: Indicates temperature errors, range 0 - 2
4th byte: Indicates cover open errors, range 0 - 2
5th byte: Indicates filter errors, range 0 - 2
6th byte: Indicates other errors, range 0 - 2
Definitions for each value from 0 to 2 are as follows
0 = No error is detected
1 = Warning 2 = Error
LAMP?
Lamp status query
Parameters
1st digits (1 - 5 digits): Lamp 1 cumulative operating time
2nd digits: 0 = Lamp 1 off, 1 = Lamp 1 on
3rd digits (0 - 5 digits): Lamp 2 cumulative operating time
4th digits: 0 = Lamp 2 off, 1 = Lamp 2 on
INST?
Input selection list query
Parameters are returned with the following values.
“11 12 21 22 31 32”
NAME?
Projector name query
Returns the name set in [PROJECTOR NAME] of [NETWORK SETUP].
INF1?
Manufacturer name query
Returns “Panasonic”.
INF2?
Model name query
Returns “DW740” or “DX810”.
INF0?
Other information queries
Returns information such as version number.
CLSS?
Class information query
Returns “1”.
ERST?
PJLink security authentication
The password used for PJLink is the same as that of the password set for Web control.
When using the projector without security authentication, do not set a password for Web control.
ffFor specifications regarding PJLink, refer to the Japan Business Machine and Information System Industries Association website.
URL http://pjlink.jbmia.or.jp/english/
118 - ENGLISH
Chapter 6 Appendix — Technical information
Control commands via LAN
When WEB control administrator rights password is set (Protect mode)
Connection method
1) Obtain the IP address and port number (Initial
set value = 1024) of the projector and request
for a connection to the projector.
ffYou can obtain both the IP address and the port number from
the menu screen of the projector.
IP address
Port number
Obtain from the main menu → [NETWORK] → [NETWORK STATUS].
Obtain from the main menu →[NETWORK] → [NETWORK CONTROL] → [COMMAND PORT].
2) Check the response from the projector.
rrResponse data
Data section
Blank
Mode
Blank
Random number section
Termination
symbol
“NTCONTROL”
(ASCII string)
‘’
0x20
‘1’
0x31
‘’
0x20
“zzzzzzzz”
(ASCII code hexadecimal number)
(CR)
0x0d
9 bytes
1 byte
1 byte
1 byte
8 bytes
1 byte
ffMode: 1 = Protect mode
3) Generate a 32-byte hash value from the
following data using MD5 algorithm.
rr“xxxxxx:yyyyy:zzzzzzzz”
xxxxxx
Administrator rights user name for Web control (default user name is “admin1”)
yyyyy
Password of above administrator rights user (default password is “panasonic")
zzzzzzzz
8-byte random number obtained in Step 2)
Command transmission method
Transmit using the following command formats.
rrTransmitted data
Header
Data section
Termination symbol
Hash value
(Refer to the preceding
“Connection method”)
‘0’
0x30
‘0’
0x30
Control command
(ASCII string)
(CR)
0x0d
32 bytes
1 byte
1 byte
Undefined length
1 byte
rrReceived data
Data section
Termination symbol
‘0’
0x30
Header
‘0’
0x30
Control command
(ASCII string)
(CR)
0x0d
1 byte
1 byte
Undefined length
1 byte
ENGLISH - 119
Chapter 6 Appendix — Technical information
rrError response
Error message
“ERR1”
Undefined control command
“ERR2”
Out of parameter range
“ERR3”
Busy state or no-acceptable period
“ERR4”
Timeout or no-acceptable period
“ERR5”
Wrong data length
“ERRA”
Password mismatch
Termination symbol
(CR)
0x0d
4 bytes
1 byte
When WEB control administrator rights password is not set (Non-protect mode)
Connection method
1) Obtain the IP address and port number (Initial
set value = 1024) of the projector and request
for a connection to the projector.
ffYou can obtain both the IP address and the port number from
the menu screen of the projector.
IP address
Obtain from the main menu → [NETWORK] → [NETWORK STATUS].
Port number
Obtain from the main menu → [NETWORK] → [NETWORK CONTROL] → [COMMAND PORT].
2) Check the response from the projector.
rrResponse data
Data section
Blank
Mode
Termination symbol
“NTCONTROL”
(ASCII string)
‘’
0x20
‘0’
0x30
(CR)
0x0d
9 bytes
1 byte
1 byte
1 byte
ffMode: 0 = Non-protect mode
Command transmission method
Transmit using the following command formats.
rrTransmitted data
Header
Data section
Termination symbol
‘0’
0x30
‘0’
0x30
Control command
(ASCII string)
(CR)
0x0d
1 byte
1 byte
Undefined length
1 byte
Data section
Termination symbol
‘0’
0x30
‘0’
0x30
Control command
(ASCII string)
(CR)
0x0d
1 byte
1 byte
Undefined length
1 byte
rrReceived data
Header
120 - ENGLISH
Chapter 6 Appendix — Technical information
rrError response
Error message
“ERR1”
Undefined control command
“ERR2”
Out of parameter range
“ERR3”
Busy state or no-acceptable period
“ERR4”
Timeout or no-acceptable period
“ERR5”
Wrong data length
“ERRA”
Password mismatch
Termination symbol
(CR)
0x0d
4 bytes
1 byte
<SERIAL IN>/<SERIAL OUT> terminal
The <SERIAL IN>/<SERIAL OUT> terminal of the projector conforms with RS-232C so that the projector can be connected to and controlled
from a computer.
Connection
For one projector
For multiple projectors
Projector 1 connecting terminals Projector 2 connecting terminals
D-Sub 9p
(female)
The projector connecting terminals
D-Sub 9p (female)
Computer
Computer
D-Sub 9p
(male)
D-Sub 9p (male)
Communication cable
Communication cable
D-Sub 9p
(male)
D-Sub 9p
(female)
D-Sub 9p
(female)
D-Sub 9p
(male)
D-Sub 9p
(male)
Communication cable
Pin assignments and signal names
D-Sub 9-pin (female)
Outside view
(6)
(1)
(9)
(5)
D-Sub 9-pin (male)
Outside view
(9)
(5)
(6)
(1)
Pin No.
Signal name
Details
(1)
―
(2)
TXD
Transmitted data
Received data
(3)
RXD
(4)
―
(5)
GND
(6)
―
(7)
CTS
(8)
RTS
(9)
―
Pin No.
Signal name
(1)
―
NC
Connected internally
Earth
NC
Connected internally
NC
Details
NC
(2)
RXD
Received data
(3)
TXD
Transmitted data
(4)
―
(5)
GND
(6)
―
(7)
RTS
(8)
CTS
(9)
―
NC
Earth
NC
Connected internally
NC
Communication conditions (Factory default settings)
Signal level
RS-232C-compliant
ENGLISH - 121
Chapter 6 Appendix — Technical information
Sync. method
Baud rate
Asynchronous
9 600 bps
Parity
None
Character length
8 bit
Stop bit
1 bit
X parameter
None
S parameter
None
Basic format
Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according
to the details of control.
(2 bytes) ID2 characters Semi-colon
Colon (1 byte)
(2 bytes)
(1 byte)
Start (1 byte)
Parameter
Command 3 characters
ZZ, 01 – 64 and 0A – 0Z
(undefined
length)
(3 bytes)
ID setting area
End (1 byte)
Attention
ff If a command is transmitted after the lamp starts illuminating, there may be a delay in response or the command may not be executed. Try
sending or receiving any command after 60 seconds.
ff When transmitting multiple commands, be sure to wait until 0.5 seconds has elapsed after receiving the response from the projector before
sending the next command. When transmitting a command which does not need a parameter, a colon (:) is not necessary.
Note
If a command cannot be executed, an “ER401” response is sent from the projector to the computer.
If an invalid parameter is sent, an “ER402” response is sent from the projector to the computer.
ID transmission in RS-232C supports ZZ (ALL) and 01 to 64, as well as 0A to 0Z groups.
If a command is sent with a specified ID, a response will be sent to the computer only in the following cases.
ggIt matches the projector ID
ggID setting is set to ALL and [RESPONSE(ID ALL)] is [ON]
ggID setting is set to GROUP and [RESPONSE(ID GROUP)] is [ON]
ff STX and ETX are character codes. STX shown in hexadecimal is 02, and ETX shown in hexadecimal is 03.
ff
ff
ff
ff
When multiple projectors are controlled
When multiple projectors are all controlled
When controlling multiple projectors together via RS-232C, perform the following settings.
1) Set a different ID for each projector.
3) Set [RESPONSE(ID ALL)] to [OFF] for all other
projectors set in Step 2).
2) Set [RESPONSE(ID ALL)] to [ON] in only one
projector.
When multiple projectors are all controlled by group unit
When controlling multiple projectors by group unit via RS-232C, perform the following settings.
1) Set a different ID for each projector.
2) Set [RESPONSE(ID GROUP)] to [ON] in only
3) Set [RESPONSE(ID GROUP)] to [OFF] for all
other projectors set in Step 2).
one projector.
Note
ff There will be no response if 2 or more projectors have [RESPONSE(ID ALL)] set to [ON].
ff There will be no response if 2 or more projectors of the same group have [RESPONSE(ID GROUP)] set to [ON].
ff When setting multiple groups, set [RESPONSE(ID ALL)] to [ON] in only one projector in each group.
122 - ENGLISH
Chapter 6 Appendix — Technical information
Cable specifications
<When connected to a computer>
1
NC NC
2
3
Projector
(<SERIAL IN>
terminal)
4
NC NC
5
6
1
1
2
2
3
3
4
4
5
NC NC
7
6
Computer
(DTE specifications)
Projector 1
(<SERIAL OUT>
terminal)
7
8
9
<When connected multiple projectors>
NC NC
NC NC
1
2
3
NC NC
4
5
6
5
NC NC
6
7
8
8
9
9
Projector 2
(<SERIAL IN>
terminal)
7
8
NC NC
9
Control commands
The following table lists the commands that can be used to control the projector using a computer.
rrProjector control command
Command
Details
Remarks (parameters)
PON
Power on
POF
Power standby
QPW
Power query
000 = Standby
001 = Power on
Switching the input signal
VID = VIDEO
SVD = S-VIDEO
RG1 = RGB1
RG2 = RGB2
DVI = DVI-D
HD1 = HDMI
Query for active lamp selection
0 = Dual
1 = Single*
2 = Lamp1
3 = Lamp2
LPM
Lamp mode
0 = Dual
1 = Single*
2 = Only Lamp1 on
3 = Only Lamp2 on
OLP
Lamp power
0 = Normal
1 = ECO
IIS
QSL
To check if the power is on, use the “Power query” command.
*Use either lamp 1 or lamp 2 whichever has the shortest cumulative operating time.
ENGLISH - 123
Chapter 6 Appendix — Technical information
<REMOTE 2 IN> terminal
It is possible to control the projector remotely (by external contact) from a control panel located away from the projector where remote control
signals cannot reach. Use the <REMOTE 2 IN> terminal on the connecting terminals of the projector to connect to the control panel.
Remote control
Contact control
Remote control/Contact control
Standby
Lit
Lamp
RGB1
VIDEO
RGB2
S-VIDEO
DVI-D
HDMI
Remote control panel in another location
Meeting room or other installation location
Pin assignments and signal names
D-Sub 9-pin (Outside view)
(6)
(1)
(9)
(5)
Pin No.
Signal name
Open (H)
Short (L)
(1)
GND
―
GND
(2)
POWER
OFF
ON
(3)
RGB1
Other
RGB1
(4)
RGB2
Other
RGB2
(5)
VIDEO
Other
VIDEO
(6)
S-VIDEO
Other
S-VIDEO
(7)
DVI-D
Other
DVI-D
(8)
SHUTTER
OFF
ON
RST/SET
Controlled by remote
control
Controlled by external
contact
(9)
Attention
ff When controlling, make sure to short-circuit pins (1) and (9).
ff When pins (1) and (9) are short-circuited, the following buttons on the control panel and the remote control cannot be used.
The power on <b> button, the power standby <v> button, the <SHUTTER> button, and the RS-232C commands and network functions
corresponding to these functions cannot be used either.
ff When pins (1) and (9) are short-circuited, do not short-circuit any pins from (3) to (7) with pin (1). The following buttons on the control panel
and the remote control cannot be used.
The power on <b> button, the power standby <v> button, <RGB1> button, <RGB2> button, <DVI-D> button, <VIDEO> button, <S-VIDEO>
button, <HDMI> button, <SHUTTER> button, and the RS-232C commands and network functions corresponding to these functions cannot
be used either.
Note
ff For pin (2) to pin (8) settings, you can make changes if you set [REMOTE2 MODE] to [USER] (x page 81).
124 - ENGLISH
Chapter 6 Appendix — Technical information
Two window display combination list (PT-DW740E only)
RGB1
Still
image
RGB1
Movie
RGB2
Still
image
RGB2
Movie
VIDEO
S-VIDEO
DVI-D
Still
image
DVI-D
Movie
HDMI
Still
image
HDMI
Movie
RGB1
Still image
―
―
l
l
l
l
l
l
l
l
RGB1
Movie
―
―
l
―
―
―
l
―
l
―
RGB2
Still image
l
l
―
―
l
l
l
l
l
l
RGB2
Movie
l
―
―
―
―
―
l
―
l
―
Input B
Input A
VIDEO
l
―
l
―
―
―
l
―
l
―
S-VIDEO
l
―
l
―
―
―
l
―
l
―
DVI-D
Still image
l
l
l
l
l
l
―
―
―
―
DVI-D
Movie
l
―
l
―
―
―
―
―
―
―
HDMI
Still image
l
l
l
l
l
l
―
―
―
―
HDMI
Movie
l
―
l
―
―
―
―
―
―
―
l: Two window display combination is possible
-: Two window display combination is not possible
Signals handled as “movie”:
ff480i, 576i, 480p, 576p, 1080/60i, 1080/50i, 1080/60p, 1080/50p, 1080/24sF, 1080/30p, 1080/25p, 1080/24p, 720/60p, 720/50p, NTSC, PAL,
SECAM, NTSC4.43, PAL-M, PAL-N, PAL60
Menu lock password
To revert to the factory default password (AAAA), perform the following operations while the screen asking for a menu lock password input is
displayed.
1) Press the <AUTO SETUP> button on the
remote control or control panel for at least two
seconds.
2) Press s for at least 2 seconds.
List of compatible signals
The following table specifies the types of signals compatible with the projector.
ffSignals that show formats are as follows.
ggV: Video
ggS: S video
ggR: RGB
ggY: YCBCR/YPBPR
ggH: HDMI
ggD: DVI-D
Horizontal
(kHz)
Vertical
(Hz)
Dots
clock
frequency
(MHz)
720 x 480i
15.7
59.9
―
720 x 576i
15.6
50.0
―
Mode
Resolution
(Dots)
NTSC/NTSC4.43/
PAL-M/PAL60
PAL/PAL-N/SECAM
Scanning frequency
Plug and play*3
Format
RGB2
DVI-D
EDID1
DVI-D
EDID2
DVI-D
EDID3
HDMI
V/S
―
―
―
―
―
V/S
―
―
―
―
―
525i (480i)
720 x 480i
15.7
59.9
13.5
R/Y
―
―
―
―
―
625i (576i)
720 x 576i
15.6
50.0
13.5
R/Y
―
―
―
―
―
525p (480p)
720 x 483
31.5
59.9
27.0
R/Y/H/D
―
3
―
3
3
625p (576p)
720 x 576
31.3
50.0
27.0
R/Y/H/D
―
3
―
3
3
750 (720)/60p
1 280 x 720
45.0
60.0
74.3
R/Y/H/D
―
3
―
3
3
750 (720)/50p
1 280 x 720
37.5
50.0
74.3
R/Y/H/D
―
3
―
3
3
1125 (1080)/60i*1
1 920 x 1 080i
33.8
60.0
74.3
R/Y/H/D
―
3
―
3
3
1125 (1080)/50i
1 920 x 1 080i
28.1
50.0
74.3
R/Y/H/D
―
3
―
3
3
ENGLISH - 125
Chapter 6 Appendix — Technical information
Resolution
(Dots)
Mode
Scanning frequency
Horizontal
(kHz)
Vertical
(Hz)
Dots
clock
frequency
(MHz)
Plug and play*3
Format
RGB2
DVI-D
EDID1
DVI-D
EDID2
DVI-D
EDID3
HDMI
1125 (1080)/24p
1 920 x 1 080
27.0
24.0
74.3
R/Y/H/D
―
3
―
3
3
1125 (1080)/24sF
1 920 x 1 080i
27.0
24.0
74.3
R/Y/H/D
―
―
―
―
―
1125 (1080)/25p
1 920 x 1 080
28.1
25.0
74.3
R/Y/H/D
―
3
―
3
―
1125 (1080)/30p
1 920 x 1 080
33.8
30.0
74.3
R/Y/H/D
―
―
―
―
―
1125 (1080)/60p
1 920 x 1 080
67.5
60.0
148.5
R/Y/H/D
―
3
―
3
3
1125 (1080)/50p
1 920 x 1 080
56.3
50.0
148.5
R/Y/H/D
―
3
―
3
3
VESA400
640 x 400
37.9
85.1
31.5
R/H/D
―
―
―
―
―
―
VGA
SVGA
MAC16
XGA
MXGA
MAC21
640 x 400
31.5
70.1
25.2
R/H/D
―
―
―
―
640 x 480
31.5
59.9
25.2
R/H/D
3
3
3
3
3
640 x 480
35.0
66.7
30.2
R/H/D
―
―
―
―
―
640 x 480
37.9
72.8
31.5
R/H/D
3
―
3
3
3
640 x 480
37.5
75.0
31.5
R/H/D
3
―
3
3
3
640 x 480
43.3
85.0
36.0
R/H/D
―
―
―
―
―
800 x 600
35.2
56.3
36.0
R/H/D
3
―
3
3
3
800 x 600
37.9
60.3
40.0
R/H/D
3
―
3
3
3
800 x 600
48.1
72.2
50.0
R/H/D
3
―
3
3
3
800 x 600
46.9
75.0
49.5
R/H/D
3
―
3
3
3
800 x 600
53.7
85.1
56.3
R/H/D
―
―
―
―
―
832 x 624
49.7
74.6
57.3
R/H/D
3
―
3
3
3
―
1 024 x 768
39.6
50.0
51.9
R/H/D
―
―
―
―
1 024 x 768
48.4
60.0
65.0
R/H/D
3
―
3
3
3
1 024 x 768
56.5
70.1
75.0
R/H/D
3
―
3
3
3
1 024 x 768
60.0
75.0
78.8
R/H/D
3
―
3
3
3
1 024 x 768
65.5
81.6
86.0
R/H/D
―
―
―
―
―
1 024 x 768
68.7
85.0
94.5
R/H/D
―
―
―
―
―
1 024 x 768
80.0
100.0
105.0
R/H/D
―
―
―
―
―
1 024 x 768
99.0
119.8
137.8
R/H/D
―
―
―
―
―
1 152 x 864
64.0
70.0
94.2
R/H/D
―
―
―
―
―
1 152 x 864
67.5
74.9
108.0
R/H/D
―
―
―
―
―
1 152 x 864
77.1
85.0
119.7
R/H/D
―
―
―
―
―
1 152 x 870
68.7
75.1
100.0
R/H/D
3
―
3
3
3
1 280 x 768
39.6
49.9
65.3
R/H/D
―
―
―
―
―
1 280 x 768
47.8
59.9
79.5
R/H/D
―
―
―
―
―
1 280 x 800
41.3
50.0
68.0
R/H/D
―
―
―
―
―
1 280 x 800
49.7
59.8
83.5
MSXGA
1 280 x 960
60.0
60.0
108.0
1 280 x 1 024
64.0
60.0
108.0
R/H/D
3
―
3
3
3
SXGA
1 280 x 1 024
80.0
75.0
135.0
R/H/D
3
―
3
3
3
―
1280 x 768
1280 x 800
SXGA+
R/H/D
3
*4
―
3
R/H/D
―
―
―
*4
*4
3
3*4
―
―
1 280 x 1 024
91.1
85.0
157.5
R/H/D
―
―
―
―
1 400 x 1 050
65.2
60.0
122.6
R/H/D
3
―
3
3
3
1 400 x 1 050
82.2
75.0
155.9
R/H/D
―
―
―
―
―
WXGA+
1 440 x 900
55.9
59.9
106.5
R/H/D
―
―
―
―
―
UXGA
1 600 x 1 200
75.0
60.0
162.0
R/H/D
3
―
3
3
3
―
WSXGA+
1 680 x 1 050
65.3
60.0
146.3
R/H/D
―
―
―
―
1920 x 1080
1 920 x 1 080*2
66.6
59.9
138.5
R/H/D
―
―
―
―
―
WUXGA
1 920 x 1 200*2
74.0
60.0
154.0
R/H/D
3
―
3
―
―
*1 When a 1125 (1035)/60i signal was input, it is displayed as a 1125 (1080)/60i signal.
*2 VESA CVT-RB (Reduced Blanking) compatible
*3 Signals with a l in the Plug and play columns are signals described in the projector's EDID (extended display identification data). If a signal has no
l in the Plug and play columns but has an entry in the Format column, it can be input. For signals without a l in the Plug and play columns, there
may be instances where resolution cannot be selected in the computer even though the projector supports them.
*4 Only for PT-DW740E
126 - ENGLISH
Chapter 6 Appendix — Technical information
Note
ff The number of display dots for PT-DW740E is 1 280 x 800, and that for PT-DX810E is 1 024 x 768. A signal with a different resolution is
converted to the number of display dots and displayed.
ff The “i” at the end of the resolution indicates an interlaced signal.
ff When interlaced signals are connected, flickering may occur on the projected image.
ENGLISH - 127
Chapter 6 Appendix — Specifications
Specifications
The following table describes the specifications of the projector.
Model No.
PT-DW740E
PT-DW740EL
Power supply
Power consumption
Panel size
DLP chips
Lens
760 W (4.3 A)
(0.3 W when [STANDBY MODE] is set to [ECO], and 8 W when set to [NORMAL])
0.65" (aspect ratio 16:10)
1 024 000 pixels
(1 280 x 800 dots)
1.8 to 2.5:1
Power focus
F = 1.7 to 1.9
f = 25.6 mm to 35.7 mm
For video signals
(including S
video)
For RGB signals
Supported
scanning
frequency
For YCBCR/YPBPR
signals
786 432 pixels
(1 024 x 768 dots)
1.8 to 2.5:1
Optional
Luminous lamp
Contrast ratio
0.7" (aspect ratio 4:3)
1-unit DLP chips, DLP type
Power zoom
Light output
PT-DX810EL
AC 220 V - 240 V 50 Hz/60 Hz
Display method
Number of pixels
PT-DX810E
F = 1.7 to 1.9
f = 25.6 mm to 35.7 mm
Optional
300 W (maximum 310 W) UHM lamp x 2
7 000 lm *1(ANSI)
8 200 lm *1 (ANSI)
2 500:1
(when [CONTRAST MODE] is [HIGH])
2 000:1
(when [CONTRAST MODE] is [HIGH])
Horizontal: 15.75 kHz/15.63 kHz, Vertical: 50 Hz/60 Hz
Horizontal: 15 kHz to 91 kHz, Vertical: 50 Hz to 85 Hz
PIAS (Panasonic Intelligent Auto Scanning) system
Dot clock frequency
162 MHz or less
ff525i (480i)
Horizontal: 15.75 kHz, Vertical: 60 Hz
ff525p (480p)
Horizontal: 31.5 kHz, Vertical: 60 Hz
ff750 (720)/60p
Horizontal: 45 kHz, Vertical: 60 Hz
ff1125 (1035)/60i
Horizontal: 33.75 kHz, Vertical: 60 Hz
ff1125 (1080)/50i
Horizontal: 28.13 kHz, Vertical: 50 Hz
ff1125 (1080)/24sF
Horizontal: 27 kHz, Vertical: 48 Hz
ff1125 (1080)/30p
Horizontal: 33.75 kHz, Vertical: 30 Hz
ff1125 (1080)/50p
Horizontal: 56.25 kHz, Vertical: 50 Hz
ff625i (576i)
Horizontal: 15.63 kHz, Vertical: 50 Hz
ff625p (576p)
Horizontal: 31.25 kHz, Vertical: 50 Hz
ff750 (720)/50p
Horizontal: 37.5 kHz, Vertical: 50 Hz
ff1125 (1080)/60i
Horizontal: 33.75 kHz, Vertical: 60 Hz
ff1125 (1080)/24p
Horizontal: 27 kHz, Vertical: 24 Hz
ff1125 (1080)/25p
Horizontal: 28.13 kHz, Vertical: 25 Hz
ff1125 (1080)/60p
Horizontal: 67.5 kHz, Vertical: 60 Hz
ffThe SYNC/HD and VD terminals do not support 3 value SYNC.
525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p,1125 (1080)/60i, 1125 (1080)/50i,
1125 (1080)/24p, 1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p, 1125 (1080)/60p, 1125 (1080)/50p
For DVI-D signal
ffDisplayable resolution: VGA to WUXGA (non-interlaced)
WUXGA signal supports only VESA CVT-RB (Reduced Blanking) signal.
ffDot clock frequency: 25 MHz to 162 MHz
525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i,
1125 (1080)/24p, 1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p, 1125 (1080)/60p, 1125 (1080)/50p
For HDMI signal
ffDisplayable resolution: VGA to WUXGA (non-interlaced)
WUXGA signal supports only VESA CVT-RB (Reduced Blanking) signal.
ffDot clock frequency: 25 MHz to 162 MHz
Color system
7 standards (NTSC/NTSC4.43/PAL/PAL-N/PAL-M/SECAM/PAL60)
Projection screen size
1.27 m (50") - 15.24 m (600")*2
Screen aspect ratio
Projection method
16:10
4:3
[FRONT/CEILING], [FRONT/FLOOR], [REAR/CEILING], [REAR/FLOOR]
*1 Value for the supplied standard zoom lens. The value varies depending on the lens. Measurement, measuring conditions and method of notation
all comply with ISO21118 international standards.
*2 The size is maximum 200" when ET-DLE055 lens is used.
128 - ENGLISH
Chapter 6 Appendix — Specifications
Model No.
PT-DW740E
PT-DW740EL
PT-DX810E
PT-DX810EL
1 set (BNC x 5)
<RGB 1 IN>
terminal
RGB signals
0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
YPBPR signal
SYNC/HD
TTL high impedance, automatic positive/negative polarity compatible
VD
TTL high impedance, automatic positive/negative polarity compatible
Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
1 set, high-density D-Sub 15p (female)
<RGB 2 IN>
terminal
RGB signals
0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
YPBPR signal
Terminals
SYNC/HD
TTL high impedance, automatic positive/negative polarity compatible
VD
TTL high impedance, automatic positive/negative polarity compatible
Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
<DVI-D IN>
terminal
1 set, DVI-D 24 p single link, DVI 1.0 compatible, HDCP compliant
<HDMI IN>
terminal
1 set, HDMI 19 pin, HDCP compliant
<VIDEO IN>
terminal
1 set, BNC 1.0 V [p-p] 75 Ω
<S-VIDEO IN>
terminal
1 set, Mini DIN 4 p Y 1.0 V [p-p], C 0.286 V [p-p] 75 Ω S1 signal compatible
<SERIAL IN>/
<SERIAL
D-Sub 9 p, each set, RS-232C compatible, for computer control
OUT> terminal
<REMOTE 1
IN>/ <REMOTE
M3 stereo mini jack, 1 set each for remote control (wired)/for projector serial control
1 OUT>
terminal
<REMOTE 2
IN> terminal
1 set D-Sub 9 p (female) for contact control
<LAN>
terminal
1 set, (for RJ-45 network connection, PJLink compatible, 10Base-T/100Base-TX)
Power cable length
3.0 m (118-1/8")
Outer case
Molded plastic
Width: 498 mm
(19-19/32")
Height: 175 mm
(6-7/8") (with minimum
feet length)
Depth: 466 mm
(18-11/32") (including the
standard zoom lens)
Dimensions
Approx 16.3 k]
(35.9 lbs.)*3
(including the standard
zoom lens)
Weight
Operating environment
Power supply
Remote
control
Operating
range
Weight
Dimensions
Width: 498 mm
(19-19/32")
Height: 175 mm
(6-7/8") (with minimum
feet length)
Depth: 432 mm
(17")
Approx 15.4 k] (34 lbs.)*3
Width: 498 mm
(19-19/32")
Height: 175 mm
(6-7/8") (with minimum
feet length)
Depth: 466 mm
(18-11/32") (including the
standard zoom lens)
Approx 16.3 k]
(35.9 lbs.)*3
(including the standard
zoom lens)
Width: 498 mm
(19-19/32")
Height: 175 mm
(6-7/8") (with minimum
feet length)
Depth: 432 mm
(17")
Approx 15.4 k] (34 lbs.)*3
Operating environment temperature*4: 0°C (32°F) to 45°C (113°F)
Operating environment humidity: 20% to 80% (no condensation)
DC 3 V (AA/R6 battery x 2)
Within 30 m (98'5") (when operated directly in front of signal receiver)
134 ] (4.7 ozs.) (including batteries)
Width: 51 mm (2") Height: 176 mm (6-15/16") Depth: 22.7 mm (29/32")
*3 Average value. Weight varies for each product.
*4 When using the projector at high altitudes (1 400 m (4 593 ft) – 2 700 m (8 858 ft) above sea level), the operating environment temperature will be
5°C (41°F) lower than the maximum limit. In addition, when [LAMP SELECT] on the menu is set to [DUAL], and [LAMP POWER] is set to [NORMAL],
if the ambient temperature exceeds 40°C (104°F) (35°C (95°F) in [HIGH ALTITUDE MODE]), light output is sometimes reduced by 20% to protect
the projector.
Note
ff The model numbers of accessories and optional components are subject to change without notice.
ENGLISH - 129
Chapter 6 Appendix — Dimensions
Dimensions
20 (25/32")
77.5 (3-1/16")
5 (3/16")
498 (19-19/32")
*The above shows the dimensions with the standard zoom lens attached.
*Actual dimensions may differ depending on the product.
130 - ENGLISH
21 (13/16")
155 (6-3/32")
43 (1-11/16")
9 (11/32")
423 (16-21/32")
Units: mm
Chapter 6 Appendix — Ceiling mount bracket safeguards
Ceiling mount bracket safeguards
ffWhen installing the projector to a ceiling, be sure to use the specified ceiling mount bracket (ET-PKD56H: for high ceilings, ET-PKD55S: for
low ceilings).
ffWhen installing the projector, attach the drop-prevention set included with the ceiling mount bracket to the projector.
If you need the special drop-prevention set (Product No.: TTRA0214), consult your dealer.
ffRequest for a qualified technician to do the installation.
ffTakes no responsibility for any damage to the projector resulting from use of a ceiling mount bracket not manufactured by Panasonic or the
inappropriate choice of location for installation, even if the warranty period of the projector has not expired.
ffUnused products must be removed promptly by a qualified technician.
ffUse a torque screwdriver or Allen torque wrench to tighten bolts to their specified tightening torques. Do not use tools such as electric
screwdrivers or impact screwdrivers.
ffFor details, read the installation manual that comes with the ceiling mount bracket.
ffThe model numbers of accessories and optional components are subject to change without notice.
Bottom view
Model No. of ceiling mount bracket: ET-PKD56H (for high ceilings)
ET-PKD55S (for low ceilings)
M6
12 mm (15/32")
Torque: 4 ± 0.5 N·m
ENGLISH - 131
Index
Index
A
Accessories………………………………………… 17
<AC IN> terminal…………………………………… 21
Adjusting adjustable feet…………………………… 34
[ADVANCED MENU]………………………… 53, 64
[AI]…………………………………………………… 58
Air filter unit…………………………………………112
Air filter unit compartment…………………………112
[ASPECT]…………………………………………… 60
<ASPECT> button
Remote control……………………………… 20, 49
Aspect function……………………………………… 49
[AUTO SETUP]……………………………………… 70
<AUTO SETUP> button
Projector body……………………………… 22, 48
Remote control……………………………… 20, 48
Auto setup function………………………………… 48
[AUTO SIGNAL]…………………………………… 70
B
[BACK COLOR]…………………………………… 72
[BLANKING]………………………………………… 64
[BRIGHTNESS]…………………………………… 55
C
Cautions on use…………………………………… 16
Cautions when installing…………………………… 14
Cautions when transporting……………………… 14
Ceiling mount bracket………………………………131
Ceiling mount bracket safeguards…………………131
[CLAMP POSITION]……………………………… 65
[CLOCK PHASE]…………………………………… 62
[COLOR]…………………………………………… 56
[COLOR CORRECTION]………………………… 69
[COLOR MATCHING]……………………………… 68
[COLOR TEMPERATURE]………………………… 56
Connecting the power cord………………………… 41
Connection………………………………………… 37
[CONTRAST]……………………………………… 55
[CONTRAST MODE]……………………………… 69
[CONTROL DEVICE SETUP]…………………… 90
[COOLING CONDITION]………………………… 76
CRESTRON RoomView……………………… 93, 106
[CUT OFF]…………………………………………… 74
D
[DATE AND TIME]………………………………… 83
<DEFAULT> button
Remote control……………………………… 20, 51
Deleting the registered data……………………… 86
[DIGITAL CINEMA REALITY]……………………… 64
Dimensions…………………………………………130
Direct Power Off Function………………………… 44
Display language……………………………… 53, 67
[DISPLAY OPTION]…………………………… 53, 68
[DISPLAY SETTING]……………………………… 89
Disposal……………………………………………… 16
<DVI-D> button
Projector body……………………………… 22, 48
Remote control……………………………… 20, 48
[DVI-D IN]…………………………………………… 70
E
[EDGE BLENDING]…………………………………
<ENTER> button
Projector body……………………………………
Remote control……………………………………
Expanding signal lock-in range……………………
65
22
20
87
F
Filter indicator……………………………………… 111
<FOCUS> button
Remote control……………………………… 20, 45
[FREEZE]…………………………………………… 73
Function button………………………………… 49, 82
<FUNCTION> button
Remote control……………………………… 20, 49
H
<HDMI> button
Projector body…………………………………… 22
Remote control……………………………… 20, 48
[HDMI IN]…………………………………………… 71
[HIGH ALTITUDE MODE]………………………… 76
I
<ID ALL> button
Remote control……………………………… 20, 23
<ID SET> button
Remote control……………………………… 20, 23
[INITIALIZE]………………………………………… 84
132 - ENGLISH
Initial setting………………………………………… 19
[INPUT RESOLUTION]…………………………… 65
Installation precautions…………………………… 14
K
[KEYSTONE]………………………………………… 63
L
Lamp indicator………………………………………110
[LAMP POWER]…………………………………… 77
[LAMP RELAY]……………………………………… 77
[LAMP SELECT]…………………………………… 76
Lamp unit cover…………………………………… 21
<LENS> button
Projector body……………………………… 22, 45
List of compatible signals…………………………125
[LOAD ALL USER DATA]………………………… 84
M
Main menu…………………………………………… 52
Main power switch…………………………… 21, 42
Maintenance…………………………………………112
Managing the sub memory list…………………… 87
<MENU> button
Projector body……………………………… 22, 51
Remote control……………………………… 20, 51
Menu item…………………………………………… 52
[MENU LOCK]……………………………………… 90
[MENU LOCK PASSWORD]……………………… 90
N
Navigating through the menu……………………… 51
[NETWORK]…………………………………… 54, 92
Network connections……………………………… 93
[NETWORK CONTROL]…………………………… 92
[NETWORK SETUP]……………………………… 92
[NETWORK STATUS]……………………………… 93
[NOISE REDUCTION]……………………………… 58
[NO SIGNAL SHUT-OFF]………………………… 82
O
<ON SCREEN> button
Remote control……………………………… 20, 47
[ON-SCREEN DISPLAY]…………………………… 71
On-screen menu…………………………………… 51
Optional accessories……………………………… 18
P
[PICTURE]……………………………………… 52, 55
[PICTURE MODE]………………………………… 55
[POSITION]…………………………………… 53, 60
Power cord………………………………………… 41
Power indicator……………………………………… 42
Power on button
Projector body…………………………………… 22
Power standby button
Projector body…………………………………… 22
Remote control…………………………………… 20
Precautions for Use………………………………… 14
Projecting…………………………………………… 45
[PROJECTION METHOD]…………………… 26, 75
[PROJECTOR ID]…………………………………… 75
[PROJECTOR SETUP]……………………… 54, 75
Protecting the registered data…………………… 87
R
[RASTER POSITION]……………………………… 66
Registering a signal to the list…………………… 86
<REMOTE 1 IN> terminal………………………… 24
<REMOTE 1 OUT> terminal……………………… 24
<REMOTE 2 IN> terminal…………………………124
[REMOTE2 MODE]………………………………… 81
Remote control……………………………………… 20
Remote control operations………………………… 47
Removing/attaching the projection lens………… 35
Renaming the registered data…………………… 86
Replacing the air filter unit…………………………113
Replacing the lamp unit……………………………114
Replacing the unit…………………………………113
Resetting to the factory default…………………… 51
<RGB1> button
Projector body……………………………… 22, 48
Remote control…………………………………… 48
<RGB2> button
Projector body……………………………… 22, 48
Remote control……………………………… 20, 48
[RGB IN]…………………………………………… 70
RoomView……………………………………………106
[RS-232C]……………………………………… 80, 121
S
[SAVE ALL USER DATA]…………………………… 83
[SCHEDULE]……………………………………… 78
[SCREEN SETTING]……………………………… 69
Security……………………………………………… 15
[SECURITY]…………………………………… 54, 89
[SECURITY PASSWORD]………………………… 89
[SECURITY PASSWORD CHANGE]…………… 89
Selecting the input signal………………………… 45
<SERIAL IN> terminal………………………………121
<SERIAL OUT> terminal……………………………121
[SERVICE PASSWORD]…………………………… 84
Setting remote control ID numbers……………… 23
Setting up…………………………………………… 26
[SHARPNESS]……………………………………… 58
[SHIFT]……………………………………………… 60
<SHIFT> button
Remote control……………………………… 20, 45
<SHUTTER> button
Projector body……………………………… 22, 47
Remote control……………………………… 20, 47
[SHUTTER SETTING]……………………………… 73
[SIDE BY SIDE]……………………………… 73, 125
[SIGNAL LIST]………………………………… 54, 86
Specifications………………………………………128
[STANDBY MODE]………………………………… 78
[STARTUP INPUT SELECT]……………………… 79
[STARTUP LOGO]………………………………… 72
[STATUS]…………………………………………… 81
<STATUS> button
Remote control……………………………… 20, 48
<S-VIDEO> button
Projector body……………………………… 22, 48
Remote control……………………………… 20, 48
Switching off the projector………………………… 43
Switching the input signal………………………… 48
Switch on the projector.…………………………… 42
[SYSTEM DAYLIGHT VIEW]……………………… 57
[SYSTEM SELECTOR]…………………………… 59
T
Temperature indicator……………………………… 111
[TEST PATTERN]……………………………… 54, 85
<TEST PATTERN> button
Remote control……………………………… 20, 49
[TEXT CHANGE]…………………………………… 90
[TINT]………………………………………………… 56
Troubleshooting……………………………………116
V
<VIDEO> button
Projector body……………………………… 22, 48
Remote control……………………………… 20, 48
W
[WHITE GAIN]……………………………………… 57
Z
[ZOOM]……………………………………………… 61
<ZOOM> button
Remote control…………………………………… 45
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries should not be mixed with general household
waste. For proper treatment, recovery and recycling of old products and used batteries, please
take them to applicable collection points, in accordance with your national legislation and the
Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources
and prevent any potential negative effects on human health and the environment which could
otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact
your local municipality, your waste disposal service or the point of sale where you purchased the
items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier
for further information.
Information on Disposal in other Countries outside the European Union
These symbols are only valid in the European Union. If you wish to discard these items, please
contact your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with
the requirement set by the Directive for the chemical involved.
Environment care information for users in China
This symbol is only valid in China.
Panasonic Corporation
Web Site : http://panasonic.net/avc/projector/
© Panasonic Corporation 2012
M0812YY0 -YI