Motorola | O1 | User guide | Motorola O1 User guide

Motorola O1
Digital Cordless Telephone
For O101, O102, O103 and O104
Warning
Charge the handset for 24 hours before use.
Welcome...
to your new Motorola O1 Digital Cordless Telephone!
•
•
•
•
•
•
•
Digital call quality with a range of up to 500 metres outdoors and up to 50 metres indoors.1
Rugged design and sturdy composition makes your Motorola O1 phone ideal for outdoor use. With a
splash and dust-resistant finish and also featuring a handy torch.
Handsfree operation for greater flexibility when on the phone.
100 Name and number phonebook to store all your contact numbers for easy dialling.
Caller Display shows you who's calling and see details of the last 40 callers in a Calls list.2
Inductive charging
Register up to 5 handsets to the base without the need for additional wiring, giving you a complete
phone system on a single line.
1
2
When there is a clear line of sight between the base and handset. Any obstruction between the base and handset will
reduce the range significantly. With the base indoors and the handset indoors, the typical range is up to 50 metres.
You must subscribe to your network provider’s Caller ID or Call Waiting service for these features to work. A
subscription fee may be payable.
Please note that this equipment is not designed for making emergency telephone calls when the power fails. Alternative
arrangements should be made for access to emergency services.
Need help?
If you have any problems setting up or using your O1, please contact Customer Services on (65) 68412668.
Email: support@alcom.com.sg
Alternatively, you may find the answer in the ‘Help’ section at the back of this guide.
This User Guide provides you with all the information
you need to get the most from your phone.
Before you make your first call, you need to set up your phone.
Follow the simple instructions in ‘Getting Started’, on the next
few pages.
IMPORTANT
Only use the telephone line cord supplied.
This equipment is not designed for making emergency telephone calls when the power fails.
Alternative arrangements should be made for access to emergency services.
Got everything?
• O1 handset
•
O1 base
•
2 x rechargeable Ni-MH battery cells
•
Power Adaptor for the base
•
Telephone line cord
•
1 x Belt clip
•
Wall mounting bracket
If you have purchased a O1 multiple pack you will also have the following additional items:
•
O1 handset & charger
•
2 x rechargeable Ni-MH battery cells
•
Power Adaptor for the charger
1. Getting started ................................................6
2. Getting to know your phone ........................10
3. Using the phone............................................15
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Switch the handset power on/off..................... 15
Make an external call...................................... 15
Preparatory dialling......................................... 15
End a call ........................................................ 15
Receive a call ................................................. 15
Earpiece volume ............................................. 16
Ringer volume................................................. 16
Secrecy (mute) ............................................... 16
Handsfree ....................................................... 16
3.9.1 Make a handsfree call ........................... 16
3.9.2 Switch to handsfree during a call .......... 16
3.10 Redial.............................................................. 16
3.10.1 Dial a number from the redial list .......... 17
3.10.2 Delete a number from the redial list ...... 17
3.10.3 Delete the entire redial list .................... 17
3.10.4 Copy a redial list number to the
phonebook ............................................ 17
3.11 Keypad lock .................................................... 18
3.12 Switch the torch on/off .................................... 18
3.13 Paging ............................................................ 18
4. Phonebook ....................................................19
4.1
4.2
4
Store a phonebook name and number ........... 19
Dial an entry.................................................... 20
4.3
4.4
Edit a phonebook name or number .................20
Delete a phonebook entry ...............................20
5. Handset settings .......................................... 21
5.1
5.2
5.3
5.4
5.5
5.6
5.7
Keypad beeps..................................................21
Handset ringer volume ....................................21
Handset ringer melody ....................................21
Handset name .................................................22
Display language .............................................22
Auto answer.....................................................22
Keypad lock .....................................................23
6. Base settings ................................................ 23
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
Base ringer volume..........................................23
Base ringer melody..........................................23
PIN code..........................................................24
Dial mode ........................................................24
Recall mode.....................................................25
Restore default settings...................................25
Restore default settings without a PIN ............25
Default settings................................................26
7. Clock & alarm ............................................... 26
7.1
7.2
7.3
7.4
Set the date .....................................................26
Set the time .....................................................26
Set the alarm ...................................................27
Silence the alarm.............................................27
8. Caller ID and the Calls list........................... 27
8.1
8.2
Caller ID .......................................................... 27
Calls list ........................................................... 28
8.2.1 View and dial from the Calls list ............. 28
8.2.2 Copy a Calls list number to the
phonebook ............................................. 28
8.2.3 Delete an entry/all entries in the
Calls list ................................................. 29
9. Using additional handsets .......................... 30
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
Registering a new O1 handset ........................ 30
Registering another type of handset to
your O1 base................................................... 30
Registering your O1 handset to
another base ................................................... 31
Select a base................................................... 31
De-register a handset...................................... 31
Internal calls .................................................... 31
Transferring calls............................................. 32
3-Way Call....................................................... 32
10. Help ............................................................... 33
11. General information..................................... 34
12. Wall mounting .............................................. 40
5
1. Getting started
WARNING
Do not place your O1 in the bathroom or other humid areas.
Location
You need to place your O1 base within 2 metres of the mains
power and telephone wall sockets so that the cables will
reach. The socket-outlet shall be installed near the
equipment and shall be easily accessible.
Make sure that it is at least 1 metre away from other
electrical appliances to avoid interference. Your O1 works by
sending radio signals between the handset and base. The
strength of the signal depends on where you place the base.
Placing it as high as possible ensures the best signal.
HANDSET RANGE
The unit has a range of up to 500 metres outdoors when there
is a clear line of sight between the base and handset. Any
obstruction between the base and handset will reduce the range
significantly. With the base indoors and the handset either
indoors or outdoors, the typical range is up to 50 metres. Thick
concrete and stone walls can severely affect the range.
SIGNAL STRENGTH
The
icon on your handset indicates that you are within
range of the base. When out of range of the base, the
icon flashes. If you are on a call, you will hear a warning
beep.
6
The line will hang up if the handset moves out of range of the
base. Move closer to the base. The handset will
automatically reconnect to the base.
Setting up
IMPORTANT
The base station must be plugged into the mains power at all
times. Do not connect the telephone line cord into the wall
socket until the handset is fully charged. Use only the power
adaptor and telephone line cord supplied with the product.
Connecting the base
1. Plug the telephone line cord into the socket marked
on the underside of the base.
2. Plug the mains power adaptor into the socket marked
on the underside of the base and plug the other end
into the mains power wall socket. The green Power/In use
light comes on and you will hear a confirmation tone.
Getting started
Installing and charging the handset
1. Make sure the battery ribbon is laying flat inside the
battery compartment and insert the 2 x AAA
rechargeable Ni-MH battery cells supplied. Please note
the ’+’ and ’-’ markings inside the battery compartment
and insert in the correct direction.
2. Replace the battery cover: hook the two plastic clips into
place first, then lower and screw the cover into place.
Finally, screw the belt clip on. You can use a coin, e.g.
10c piece if you don’t have a screwdriver.
3. If you are charging the batteries for the first time, place
the handset on the base to charge for at least 24 hours
continuously.
4. When the handset is fully charged,
icon will
appear steady on the display. Plug the other end of the
telephone line cord (make sure that one end is already
plugged into the base) into the telephone wall socket.
Note
This unit adapts Induction Charging, as such there will be no
metal contacts on the handset or charging cradle
Getting started
Connecting the handset and charger
(for multi-pack only)
If you have purchased a multiple pack, you will need to carry
out this process for all the handsets and chargers.
1. Plug the charger power adaptor into the socket marked
on the underside of the charger and plug the other
end into the mains power wall socket.
2. Remove the battery cover from the back of the handset
and insert the 2 x AAA NiMH rechargeable batteries
7
supplied. Please note the ’+’ and ’-’ markings inside the
battery compartment and insert in the correct direction.
3. Replace the battery cover: hook the two plastic clips into
place first, then lower and screw the cover into place.
8
Finally, screw the belt clip on. You can use a coin, e.g.
10c piece if you do not have a screwdriver.
4. If you are charging the batteries for the first time, place
the handset on the charger to charge for at least 24
hours continuously.
5. When the handset is fully charged,
icon will
appear steady on the display.
The display will show the time and handset number
(e.g. 2) to indicate that it is registered to the base.
Getting started
IMPORTANT
Warning! Use only the approved rechargeable Ni-MH battery
cells (2 x AAA Ni-MH 550mA rechargeable batteries)
supplied with your O1.
After charging your handset for the first time, subsequent
charging time is about 6–8 hours a day. Batteries and
handset may become warm during charging. This is normal.
BATTERY LOW WARNING
If
icon flashes on the display and you hear a warning
beep every minute during a call, you will need to recharge
the handset before you can use it again.
1
All talk and standby times are approximate and depend on
features selected and usage pattern.
When charging,
icon will scroll on the display, once the
battery is fully charged the icon will stop scrolling.
If you have subscribed to a Caller ID Service, the date and
time is set automatically for all handsets when you receive
your first call.
BATTERY PERFORMANCE
In ideal conditions, fully charged batteries should give up to
10 hours talk time or up to 150 hours standby time on a
single charge1.
Note that new batteries do not reach their full capacity until
they have been put to normal use for several days.
To keep your batteries in the best condition, leave the
handset off the base for a few hours at a time.
Running the batteries right down at least once a week will
help them last as long as possible.
The charge capacity of rechargeable batteries will reduce
with time as they wear out, giving the handset less talk/
standby time. Eventually they will need to be replaced.
Getting started
Date and time
If you do not have Caller ID service, you can set the date and
time manually.
Set the date manually
1. Press m to open the main menu.
2. Press u or d until Date & Time is displayed, then press
m.
3. Set Date is displayed, press m.
4. Enter the date (dd/mm) e.g. for 15th February, press 1,
5, 0, 2, then press m.
9
Set the time manually
2. Getting to know your phone
2. Press u or d until Date & Time is displayed, then press
m.
Overview of your handset
1. Press m to open the main menu.
3. Press u or d to select Set Time and press m.
4. Enter the time in 24-hour format, e.g. for 9:24pm press
2, 1, 2, 4, then press m.
Your O1 is now ready for use.
10
Getting to know your phone
A
B
C
D
E
F
G
H
Earpiece / receiver
Display with orange backlight
I
Secrecy / Clear / Back
J
* / Keypad lock
Backlight comes on when you recieve a call or when any
button is pressed.
In talk mode, press to switch secrecy (mute) on/off, page 16.
Handsfree
In standby mode, use to switch handsfree on and off, page 16.
Phonebook / Exit
In standby or talk mode, press to open the Phonebook, page 19.
When viewing the Redial list/Calls list or when editing, press
to exit and return to standby.
Switch temporarily from pulse to tone dialling.
From standby, press and hold to lock the keypad, page 18.
K
Recall / Power On/Off
In standby mode, press to access and scroll through the
menu options, page 13.
Press to confirm a displayed option.
L
Redial / Scroll Up / Volume +
M
#
Press to change the case when entering letters/editing.
Int
Menu / OK
In standby mode, use to redial any of the last 10 numbers
called, page 16.
When dialling/storing a number, press to enter a pause,
page 20.
In talk mode, press to increase the handset volume, page 16.
Use to scroll up through the phonebook, redial list and Calls
list.
N
O
For use with a switchboard/PBX and O1 Calling Features1.
Use to switch the handset power on/off, page 15.
In standby or talk mode, use to make an internal call, page 31.
Microphone
Torch On/Off (located on the back of handset)
Press and hold to switch the torch on, page 18.
Release the button to switch the torch off, page 18.
Talk
In standby mode, press to make or receive calls.
In talk mode, press to end a call, page 15.
Calls / Scroll Down / Volume -
In standby mode, press to open the Calls list, page 28.
In talk mode, press to decrease the handset volume, page 21.
Use to scroll down through the phonebook, redial list and
Calls list.
Getting to know your phone
1
When on an external call, press Recall to get a fresh dialling
tone or to access call waiting when you hear the signal. Press
the key again to toggle between your two callers.
11
Handset LCD Display
Battery
status
Scrolls
when
charging
Flashes when handset is not registered to the base
or if you go out of range
Hands-free mode is ON
Eco mode
Circle
around
appears
when Eco
mode is ON
Menu is opened
Phonebook is opened
Alarm bell
Displayed when the alarm is set.
Display icons
Flashes to indicate new calls list entries received1
Flashes to indicate an incoming external call
Answered call (when viewing the Calls list)1
External call in progress
Unanswered call (when viewing the Calls list)1
Flashes to indicate an incoming internal call
Keypad is locked
Internal call in progress
3-way call in progress or transfer an external call to
another O1 handset registered to the base
Eco mode is ON
Battery is fully charged
Flashes to indicate new voicemail messages received
Off when you have no voicemail messages (this
feature is dependent on your Network Service
provider supporting the service)
Battery is partially charged
Indicates signal strength
12
Displayed number is longer than 12 digits
The approximate power levels of your battery are indicated
as follows:
Battery is running low
Flashes when battery is almost fully discharged
1
For this feature to work, you must subscribe to Caller ID Service
from your network operator. A subscription fee may be payable.
Getting to know your phone
Overview of the base
Navigating the menus
Your O1 has an easy to use menu system. Each menu has
a list of options, which you can see on the menu map on the
following page.
When the handset is switched on and in standby:
1. Press m to open the main menu, then press u
or d repeatedly to scroll to the menu option you want.
2. Press m to select a displayed menu option or
press n to go back to the previous screen.
Exit or go back one level in the menu:
1. Press n to go back one level.
2. Press n repeatedly to exit and return to
standby.
A
Page (Find handset)
B
Power / In use / Calls light / Message Indicator
Press to page/locate a missing handset, page 18.
Illuminates when the power is connected.
Flashes when receiving a call and during a call, when you
have new text messages or Calls list entries waiting and
when the phone is in registration mode.
Getting to know your phone
13
Menu map
Phonebook
Handset
Date & Time
Setup
Register
Add Entry
Modify Entry
Delete Entry
Ext Melody
Ext Ring Vol
Handset Name
Int Melody
Int Ring Vol
Beep
Set Date
Set Time
Set Alarm
Base Melody
Base Volume
Eco Mode
Dial Mode
Recall
Del Handset
Pin Code
Default
Select Base
Reg Base
Keytone
Low Battery
Out Of Range
Language
Auto Answer
Key Lock?
14
Getting to know your phone
3. Using the phone
NOTE
Your handset will automatically time the duration of all
external calls. The handset display shows the call duration
both during and for a few seconds after your call.
3.1
Switch the handset power on/off
To switch off:
1. Press and hold R until the display goes off.
To switch on:
1. Press and hold R for 3 seconds and the display will
come back on.
3.2
Make an external call
When you make a call, the backlight on the handset display
comes on and the In Use light on the base flashes.
1. Lift the handset and press <. The
are displayed.
and
symbols
2. When you hear the dialling tone, dial the number you want.
3.3
Preparatory dialling
1. Enter the number first. If you make a mistake, press
n to delete the last digit.
NOTE
Press u to enter a pause in the dialling sequence.
You can enter a pre-dial number up to 32 digits long, Only
the last 12 digits will be displayed.
3.4
End a call
1. Press <.
Or
Place the handset back on the charger.
3.5
Receive a call
When you receive a call, the phone rings, the
symbol
flashes, the keypad backlight comes on and the Calls light on
or
symbol
the base flashes. Call is displayed and the
flashes to let you know if it is an external or internal call.
1. If your handset is on the charger and auto-answer is on:
pick up the handset to answer the call.
Or
If your handset is on the charger and auto-answer is off:
pick up the handset and press < to answer the call.
Or
If your handset is off the charger, press <.
2. Press < to dial.
Using the phone
15
NOTE
As long as you have auto answer set to ON you can just pick
the handset up off the charger to answer a call. If you have
switched it off, you will need to press <. Auto answer ON is
the default setting. See page 22 for more information on
auto-answer.
3.6
Earpiece volume
During a call you can adjust the volume of the earpiece/
handset receiver. There are 5 volume levels to choose from.
1. Press u to increase or d to decrease the volume.
3.7
Ringer volume
While the phone is ringing, you can use u or d to adjust the
ringer volume.
3.8
Secrecy (mute)
During a call, you can mute the microphone and talk to
someone nearby without your caller hearing.
1. Press n. Mute is displayed while the
microphone is muted and your caller cannot hear you.
2. Press n again to resume your conversation
with your caller.
16
3.9
Handsfree
Handsfree lets you talk to your caller without holding the
handset. It also enables other people in the room to listen to
your conversation over the loudspeaker.
3.9.1
Make a handsfree call
1. Press M then dial the number. The
icon is
displayed and you hear your call over the loudspeaker.
2. Press < to end the call.
3.9.2
Switch to handsfree during a call
During a call:
1. Press M . The call is transferred to the
loudspeaker.
2. Press < to end the call.
NOTE
During a handsfree call, press u or d to change the
volume.
To switch handsfree off and return to the handset at any
time, press M.
3.10
Redial
The last 10 telephone numbers called are saved to a redial
list. You can then select any of the numbers to redial, delete
or copy to the directory.
Using the phone
3.10.1
Dial a number from the redial list
1. Press u. The last number called is displayed.
2. Use u or d to scroll through the redial list to the
number you want.
3. Press < to redial.
3.10.3 Delete the entire redial list
1. Press u. The last number called is displayed.
2. Press and hold n, Delete All? is displayed, press
m to confirm. Or press n to cancel.
3. Press to exit and return to standby.
NOTE
To exit the redial list at any time, press B.
3.10.4 Copy a redial list number to the phonebook
Redial numbers can be up to 32 digits long. Only the first 12
digits will be displayed, if there are more than 12 digits, the
symbol will be displayed. Press m to view the
remaining digits.
2. Use u or d to scroll and display the number you want,
then press m.
3.10.2
4. Name? is displayed. Enter a name using the keypad and
press m.
Delete a number from the redial list
1. Press u. The last number called is displayed.
2. Use u or d to scroll through the redial list to the
number you want.
3. Press n, Delete? is displayed, press m to
confirm. Or press n to cancel.
4. Press B to return to standby.
Using the phone
1. Press u. The last number called is displayed.
3. Add? is displayed, press m.
5. The redial number is displayed. If you wish you can edit
the number. When the number is correct, press
m.
6. Press u or d to select a melody and press m
to save the entry.
7. Press B to exit and return to standby.
17
3.11
Keypad lock
To switch on:
You can lock the keypad so that it cannot be used
accidentally while carrying it around.
1. Press and hold T to switch the torch light on. The
button can be found on the back of the handset.
To lock the keypad:
To switch off:
1. Press and hold * for 3 seconds. The display shows
the
symbol.
To unlock the keypad:
1. Press any key. The display shows Press *.
2. Press * within 3 seconds to unlock the keypad.
NOTE
You can also lock the keypad using the handset settings
menu, see page 23.
IMPORTANT
If the keypad is locked you will NOT be able to dial the
emergency numbers 999 and 112.
3.12
Switch the torch on/off
To help you see in dark or poorly lit environments, you may
find the torch a handy feature.
1. Release T to switch the torch light off.
3.13
Paging
You can alert a handset user that they are wanted or locate
a missing handset.
1. Press p on the base. All handsets registered to the
base will ring.
2. Press p again to stop the paging ring. Or press any
button on the handset.
NOTE
Paging calls cannot be answered by a handset.
The paging ring will stop automatically after 30 seconds if no
button is pressed and your handset will return to standby.
WARNING
Never look directly at the torch light, or shine it into the eyes
as the light is very bright. Please keep the torch away from
small children.
18
Using the phone
4. Phonebook
You can store up to 100 names and numbers in the
phonebook. Names can be up to 12 characters long and
numbers up to 24 digits. You can also select from 10
different ringtones for phonebook entries.
4.1
Store a phonebook name and number
1. Press m to open the main menu.
2. Phonebook is displayed, press m.
3. Add Entry is displayed, press m.
4. Enter a name using the keypad and press m.
5. Enter a telephone number using the keypad and press
m.
6. Use u or d to scroll through and hear a sample of
each melody. When you hear the melody you want,
press m to confirm.
7. Press n repeatedly to exit and return to standby.
ENTERING NAMES
Use the keypad letters to enter names, e.g. to store TOM:
Press 8 once to enter T.
WRITING TIPS
Press n to delete the last character or digit.
To enter a space press 0.
Use 0, 1, and * for punctuation characters.
If the next letter is on the same button as you have just
pressed, wait for the cursor to move to the right before trying
to enter it.
You MUST enter a name and a number otherwise the entry
will not be stored.
ENTERING NUMBERS
Make sure you enter the full telephone number including the
dialling code if you subscribe to a Caller Display service and
want the name of your caller displayed instead of the
number.
To enter a pause in a phonebook number, press u and a P
will be displayed. For more information on pauses, see
page 39.
NOTE
The ringer melody option means that when you receive a call
from a number stored in your phonebook the ringtone you
choose will be played.
Press 6 three times to enter O.
Press 6 once to enter M.
Phonebook
19
4.2
Dial an entry
1. Press B to open the phonebook list.
2. Use u or d to scroll and find the entry you want or
search alphabetically.
3. Press < to dial the displayed number.
NOTE
To see the number before dialling, with the entry name
displayed, press m.
If the number has more than 12 digits, press m to
view the remaining digits.
4.3
Edit a phonebook name or number
1. Press m to open the main menu.
2. PHONEBOOK is displayed, press m.
3. Press u or d to select Modify Entry and press m.
4. Use u or d to scroll and find the entry you want to edit
and press m to select.
5. The name is displayed. Use n to delete any
incorrect characters and enter new ones using the
keypad and press m to confirm.
20
6. The number is displayed. Use n to delete any
incorrect digits and enter new ones using the keypad
and press m to confirm.
7. The current melody is played. Use u or d to scroll
through and hear a sample of each melody. When you
hear the melody you want, press m to confirm.
8. Press n repeatedly to exit and return to
standby.
4.4
Delete a phonebook entry
1. Press m to open the main menu.
2. Phonebook is displayed, press m.
3. Press u or d to select Delete Entry and press m.
4. Use u or d to scroll and find the entry you want to delete
and press m to select.
5. Confirm? is displayed. Press m to confirm.
6. Press n repeatedly to exit and return to standby.
Phonebook
5. Handset settings
5.1
Keypad beeps
Your O1 phone has a selection of beeps / warning tones
which can be set to on, to alert you to certain situations:
Key tones – where a beeps sounds every time a keypad
button is pressed (to confirm the button press).
Low battery warning tone – a beep alerts you when the
batteries are low and need recharging.
Out of range tone – when the handset moves too far from
the base and goes out of communication range a warning
tone will sound.
1. Press m to open the main menu.
2. Press u or d until Handset is displayed, then press
m.
u or d key until Beep is displayed, press
m.
Use u or d to display either Keytone , Low Battery or Out Of
Range and press m.
Use u or d to select On to activate the beeps, or Off to
deactivate the beeps and press m.
Press n repeatedly to exit and return to standby.
3. Press
4.
5.
6.
Handset settings
5.2
Handset ringer volume
The handset has 6 ringer volume settings: Off and 1–5
where, 1=low and 5=high.
1. Press m to open the main menu.
2. Press u or d until Handset is displayed, then press
m.
3. Press u or d to select either Int Ring Vol or Ext Ring Vol
and press m.
4. Press u or d to highlight the volume you require and
press m to confirm.
5. Press n repeatedly to exit and return to standby.
NOTE
You will hear a sample ring for all settings (except Off).
5.3
Handset ringer melody
You can choose from 10 polyphonic ringer melodies for both
external and internal calls.
1. Press m to open the main menu.
2. Press u or d until Handset is displayed, then press
m.
3. Press u or d to select either Ext Melody or Int Melody and
press m.
21
4. Use u or d to hear and select a melody. Press
m to confirm your selection.
5. Press n repeatedly to exit and return to standby.
5.4
Handset name
You can give your handset a name to personalise it if you are
using more than one handset. The maximum number of
characters is 10.
1. Press m to open the main menu.
2. Press u or d until Handset is displayed, then press
m.
3. Press u or d to display Handset Name and press
m.
4. The existing handset name is displayed, followed by a
flashing cursor. Use n to delete the current
name and enter a name using the keypad, then press
m to confirm.
5. Press n repeatedly to exit and return to standby.
NOTE
To delete incorrect characters press n.
For help with entering names, see page 19.
5.5
Display language
You can change the language that is shown on your handset
display. There are 14 languages to choose from: English,
French, Spanish, Italian, German, Dutch, Portuguese, Danish,
Finnish, Swedish, Norwegian, Greek, Polish or Turkish.
1. Press m to open the main menu.
2. Press u or d until Handset is displayed, then press
m.
3. Press u or d to display Language and press m.
4. Press u or d to highlight the language you want and
press m to confirm.
5. Press n repeatedly to exit and return to
standby.
5.6
Auto answer
If you set auto answer to On, when you receive an incoming
call and the handset is in the charger, you can pick it up to
answer the call. You do not need to press <.
1. Press m to open the main menu.
2. Press u or d until Handset is displayed, then press
m.
3. Press u or d to display Auto Answer and press
m.
22
Handset settings
4. Press u or d to select either ON or OFF and press
m to confirm.
5. Press n repeatedly to exit and return to standby.
5.7
Keypad lock
You can lock the keypad so that it cannot be used
accidentally while carrying it around.
To lock the keypad:
1. Press m to open the main menu.
2. Press u or d until Handset is displayed, then press
m.
3. Press u or d to display Key Lock? and press m
to confirm.
6. Base settings
6.1
Base ringer volume
The base has 6 ringer volume settings: Off and 1–5 where,
1=low and 5=high.
1. Press m to open the main menu.
2. Press u or d until Setup is displayed, then press
m.
3. Base Volume is displayed, press m.
4. Press u or d to highlight the volume you require and
press m to confirm.
5. Press n repeatedly to exit and return to standby.
To unlock the keypad:
NOTE
You will hear a sample ring at the base for all settings
(except Off).
2. Press * to unlock the keypad.
6.2
NOTE
You can also lock the keypad using the * button, see
page 18.
The base has 5 ringer melodies to choose from.
1. Press any button. The display shows press *.
While the keypad is locked, the
icon will be displayed.
IMPORTANT
If the keypad is locked you will NOT be able to dial the
emergency number 999.
Base settings
Base ringer melody
1. Press m to open the main menu.
2. Press u or d until Setup is displayed, then press
m.
3. Press u or d to select Base Melody and press m.
23
4. Use u or d to hear and select a melody. Press
m to confirm your selection.
5. Press n repeatedly to exit and return to standby.
6.3
PIN code
Your O1 has a security PIN code which you will need to
change some of the settings on your phone. The default PIN
code is 0000. You may want to change this to prevent
unauthorised changes to your settings.
1. Press m to open the main menu.
2. Press u or d until Setup is displayed, then press
m.
3. Press u or d to select Pin Code and press m.
6.4
Dial mode
The dialling mode is pre-set to Tone (DTMF) dialling. If you
are using your O1 phone with an older type of switchboard/
PBX you may required to change this setting to Pulse
dialling. Contact your PBX/Switchboard provider if you are
unsure which setting to use.
1. Press m to open the main menu.
2. Press u or d until Setup is displayed, then press
m.
3. Press u or d to select Dial Mode and press .
4. Use u or d to highlight the dial mode you want and
press m to confirm your selection.
4. Enter the current 4 digit PIN code and press m.
5. Press n repeatedly to exit and return to
standby.
6. Re-enter the new PIN code and press m.
NOTE
If the dial mode is set to pulse dialling you can switch
temporarily to tone dialling for the duration of the call.
5. Enter a new 4 digit PIN code and press m.
7. Press n repeatedly to exit and return to standby.
NOTE
For security when you enter each digit of the PIN code it will
be displayed as a *.
24
After you press to get a line, press < and hold * before
you enter the telephone number. The number you enter will
be dialled out using tone dialling.
Base settings
6.5
Recall mode
Please contact your network provider is you are unsure
which setting to use.
There are 2 recall mode settings:
Timed Br. 1 100 msec
Timed Br. 2 600 msec
1. Press m to open the main menu.
2. Press u or d until Setup is displayed, then press
m.
3. Press u or d to select Recall and press m.
4. Use u or d to highlight the recall setting you want and
press m to confirm your selection.
5. Press n repeatedly to exit and return to standby.
6.6
Restore default settings
You can restore your O1 phone to its default (original)
settings as described on page 26.
1. Press m to open the main menu.
2. Press u or d until Setup is displayed, then press
m.
5. CONFIRM? is displayed, press m to confirm the
reset. The handset will switch off, then switch back on
again with the default settings restored.
NOTE
Please note, restoring the default settings will delete your
phonebook, redial and calls list.
6.7
Restore default settings without a
PIN
If you have forgotten your PIN code, you can restore your O1
to the default settings following the procedure shown below.
1. Unscrew and remove the belt clip and battery
compartment cover.
2. Remove the batteries for a few minutes. Press and hold
*, while still pressing the * button, insert the
batteries again observing the polarity markings (+ and -).
3. Default is displayed, press m.
When the phone powers up, the default settings will be
restored.
4. Replace the battery compartment cover and belt clip.
3. Press u or d to select Default and press m.
4. Enter the 4 digit PIN code and press m. (Default
PIN code setting is 0000)
Base settings
25
6.8
Default settings
Handset Name
Low Battery Tone
Out of Range Tone
Key Tones
Auto Answer
Handset Internal Ringer Melody
Handset Internal Ringer Volume
Handset External Ringer Melody
Handset External Ringer Volume
Earpiece Volume
Phonebook list
Calls List
Redial List
PIN code
Dial Mode
Keypad Lock
ECO
Recall mode
HANDSET 1
ON
ON
ON
ON
1
3
3
3
3
Empty
Empty
Empty
0000
Tone
OFF
OFF
Timed Br. 2
(600 msec)
7. Clock & alarm
7.1
Set the date
1. Press m to open the main menu.
2. Press u or d until Date & Time is displayed, then press
m.
3. Set Date is displayed, press m.
4. Enter the date (dd/mm) e.g. for 15th February, press 1,
5, 0, 2, then press m.
5. Press n repeatedly to exit and return to standby.
7.2
Set the time
Your O1 uses the 24 hour clock.
If you subscribe to a Caller Display Service from your
network provider the time will be set when you receive your
first call.
1. Press m to open the main menu.
2. Press u or d until Date & Time is displayed, then press
m.
3. Press u or d to select Set Time and press m.
4. Enter the time in 24-hour format, e.g. for 9:24pm press
2, 1, 2, 4, then press m.
5. Press n repeatedly to exit and return to standby.
26
Clock & alarm
7.3
Set the alarm
You can use your O1 phone as an alarm clock.
When the alarm is set the
when in standby mode.
symbol will be displayed
1. Press m to open the main menu.
2. Press u or d until Date & Time is displayed, then press
m.
3. Press u or d to select Set Alarm and press m.
4. Press u or d to select either:
On to switch the alarm on and press m. The
previous alarm time setting is displayed. Enter the time
you want the alarm to sound in 24 hour format e.g. for
7:30am press 0, 7, 3, 0, then press
m.
Or
Off to switch the alarm off and press m.
5. Press n repeatedly to exit and return to standby.
7.4
Silence the alarm
When the alarm time is reached, the alarm will sound and
Alarm On will flash in the display.
1. Press any button on the handset to silence the alarm.
Caller ID and the Calls list
8. Caller ID and the Calls list
IMPORTANT
To use Caller ID, you must first subscribe to the service from
your network provider. A subscription fee may be payable.
To ensure that the caller's name is displayed, make sure you
have stored the full telephone number, including the area
code in the phonebook.
If the caller’s number is stored in the phonebook, the name
assigned to it will be displayed.
If the call is a withheld call, Withheld will be displayed.
If the number is unavailable, Unavailable will be displayed.
If the call is from an international number, Int'l will be
displayed.
If the call is from the operator, Operator will be displayed.
If the call is from a payphone, Payphone will be displayed.
If the call is from a ringback request, Ringback will be displayed.
8.1
Caller ID
If you have subscribed to a Caller ID Service, you will be able
to see your caller’s number on your handset (provided it is
not withheld) prior to answering the call. The display can
show the first 12 digits or characters of the phone numbers
and names.
27
If your caller’s name and number are stored in the
phonebook and a name/number match is found, you will see
the caller’s name on the display instead.
8.2
Calls list
The Calls list stores details of your last 40 received calls,
including the phone number and date and time of the call.
The Calls list also alerts you when you have unanswered calls.
The caller’s details are stored in the Calls list whether or not
you have answered the call. The list is shared by all
handsets registered to the base. When the list is full, and a
new call is received, the oldest entry will be deleted
automatically.
When a new call is received in the Calls list,
icon will
flash on the display in standby mode to alert you. When you
have viewed the new call,
icon disappears but
icon
will remain.
8.2.1
View and dial from the Calls list
1. Press d. The most recently received number or name
is displayed.
If you answered the call, you will see the
If the call was not answered, you will see the
28
symbol.
2. Use u or d to scroll through the list.
With a name displayed, press OK repeatedly to view the
caller’s number and the date and time the call was received.
3. To dial a displayed number, press <. The number will
be dialled automatically.
Or
To exit and return to standby, press B.
When all new calls have been viewed the
will desappear from the display.
8.2.2
symbol
Copy a Calls list number to the phonebook
1. Press d. The most recently received number or name
is displayed.
If you answered the call, you will see the
If the call was not answered, you will see the
symbol.
symbol.
2. Use u or d to scroll through the list to the number you
want to store.
3. Press m repeatedly until Add? is displayed, then
press m.
symbol.
Caller ID and the Calls list
4. Enter a name using the keypad, then select the
m option.
5. The number is displayed, (if necessary, edit the
number), then press m.
6. The ringer melody options are displayed, use u or d
to scroll and hear a sample of each melody, when you
hear the one you want press m. The entry is
stored to the phonebook.
7. Press B to return to standby.
NOTE
See ENTERING NAMES and WRITING TIPS on page 19.
If you need to edit the number, use n to delete any
unwanted digits, then enter new ones using the keypad.
Caller ID and the Calls list
8.2.3
Delete an entry/all entries in the Calls list
1. Select the d option. The most recently received
number or name will be shown.
2. Use u or d to scroll through the list.
3. Press and release n to delete the currently
displayed entry only. Delete? is displayed.
Or
Press and hold to delete all entries. Delete All? is displayed.
4. Press m to confirm you want to delete.
Or
Press n if you decide not to delete.
5. Press B to return to standby.
29
9. Using additional handsets
You can use up to five GAP compatible handsets with your
O1 base to extend your phone system without needing to
install extension sockets for each new phone.
Your O1 handset can be registered to up to 4 bases. You can
then select the base you would prefer to use.
You need to register any additional handsets you purchase
to your O1 base.
NOTE
Additional handsets must be fully charged before attempting
to register.
9.1
Registering a new O1 handset
At the base:
1. Press and hold p until you hear a beep, then release it.
The base will now remain in registration mode for 90
seconds, during which time you will need to complete
the following procedure.
At the new handset:
2. Press m to open the main menu.
3. Press u or d until Register is displayed, then press
m.
5. Enter a base number (from 1 to 4) and press m.
If the handset is already registered to a base, the base
number will flash.
6. Enter the 4 digit PIN code and press m. (Default
PIN code setting is 0000)
When the base is located, your handset will display the
base ID number, press m to confirm registration
to this base or cancel by pressing B.
The handset is automatically allocated the next
available handset number which is displayed when in
standby mode.
NOTE
If registration is unsuccessful, the handset will return to
standby mode. Try moving closer to the base you want to
register to and following the registration procedure again.
9.2
Registering another type of handset
to your O1 base
At the base:
1. Press and hold p until you hear a beep, then release it.
The base will now remain in registration mode for 90
seconds, during which time you will need to complete
the registration procedure shown in the other
manufacturer’s user manual.
4. Press u or d to highlight Reg Base and press m.
30
Using additional handsets
NOTE
Handsets must be GAP compatible to be able to be
registered to your O1 base.
NOTE
When selecting a base, the currently selected base number
flashes.
9.3
If an invalid base selection is entered, you will hear the error
tone.
Registering your O1 handset to
another base
1. Follow the instructions shown in the other manufacturer’s
guide to put the base into registration mode.
2. Follow steps 2 to 6 of “Registering a new O1 handset”
on page 30 to register the handset.
9.4
Select a base
If your O1 handset is registered to more than one base, you
can select which base to use. Alternatively, if you select AUTO
your handset will automatically select the base with the best
reception.
1. Press m to open the main menu.
2. Press u or d until Register is displayed, then press
m.
3. Press u or d to highlight Select Base and press
m.
4. Press u or d to select a base number (1 to 4) or select
Auto and press m to confirm.
5. Press n repeatedly to exit and return to standby.
Using additional handsets
9.5
De-register a handset
You cannot de-register the handset you are using.
1. Press m to open the main menu.
2. Press u or d until Setup is displayed, then press
m.
3. Press u or d to select Del Handset and press m.
4. Enter the 4 digit PIN code, then press m.
5. Enter the number of the handset to be removed (1 – 5)
using the keypad. You will hear a tone to confirm the
handset has been de-registered.
6. Press n repeatedly to exit and return to standby.
9.6
Internal calls
If you have more than one handset registered to the base,
you can make internal calls between two handsets.
1. Press I. The and
symbols are displayed.
2. Enter the handset number (1-5) you want to call.
31
At the called handset, the
symbol flashes and the
calling handsets number is displayed. The user can
press < to answer the call.
3. Press < to end the call.
NOTE
If you enter an invalid handset number, the display will return
to standby.
9.7
Transferring calls
You can transfer an external call to another handset
registered to the base.
During a call:
1. Press I. The external caller will be put on hold and
will hear a tone.
2. Enter the internal handset number that you want to
transfer the call. The called handset will ring.
NOTE
If you want to cancel the call transfer, press <.
9.8
3-Way Call
You can hold a 3-way conference call between 2 internal
handsets and 1 external handset.
During a call:
1. Press I. The external caller will be put on hold and
will hear a tone.
2. Enter the internal handset number that you want to hold
the 3-way call with.
3. When the internal handset user answers, press # to
begin the 3-way call.
4. Either internal handset can press < at any time to
leave the 3-way call.
At the called handset, the user can press < to answer
the call.
3. At the original handset: When the other handset
answers, press < to complete the transfer.
If the called handset does not answer, press I to
speak to the external caller again.
32
Using additional handsets
10. Help
No dial tone
• Use only the telephone line cord supplied.
• Check that the telephone line cord is connected properly.
• Check that the mains power is connected properly and
switched on.
No display
• Check that the batteries are inserted correctly and fully
charged. Use only approved rechargeable batteries
supplied.
• Check that the handset is switched on. Press and hold
R.
• Reset the base by removing the batteries and
disconnecting the mains power. Wait for around 15
seconds before connecting it again. Allow up to one
minute for the handset and base to synchronize.
icon flashes
• Handset is out of range. Move closer to the base.
• Make sure that the handset is registered to the base, see
page 30.
• Check that the mains power is connected properly and
switched on.
Keypad does not seem to work
• Check that the keypad lock is not on, see page 18.
Help
icon is not scrolling during charge
• Adjust the handset slightly on the base.
• Check that the mains power is connected properly and
switched on.
• The battery is full. When the handset is fully charged,
icon will appear steady on the display.
No Caller ID
• Check your subscription with your network operator, see
page 27.
• The caller may have withheld their number.
• The record cannot be found in your phonebook. Check
that you have the correct name/number stored in your
phonebook, with the full area code.
I have forgotten my PIN!
• Restore your O1 to its default settings, see page 26.
Cannot register a handset to the base
• You can register up to a maximum of 5 handsets to a O1
base. You must de-register a handset in order to register
a new one, see page 31.
• Check that you have entered the correct PIN code
(default = 0000).
• Check that you are at least one metre away from other
electrical equipment to avoid interference when
registering.
33
Handset does not ring
• The handset ringer volume may be set to Off, see
page 21.
Base unit does not ring
• The base ringer volume may be set to Off, see page 23.
Noise interference on my phone or on other
electrical equipment nearby
• Place your O1 at least one metre away from electrical
appliances or any metal obstructions to avoid any risk of
interference.
11. General information
IMPORTANT
This equipment is not designed to make emergency telephone
calls when the power fails. Alternative arrangements should be
made for access to emergency services.
This product is intended for connection to analogue public
switched telephone networks and private switchboards in
Singapore.
Important safety instructions
Follow these safety precautions when using your phone to
reduce the risk of fire, electric shock, and injury to persons
or property:
1. Keep all slits and openings of the phone unblocked. Do
not set the phone on a heating register or over a
radiator. Ensure that proper ventilation is provided at the
installation site.
2. Do not use while wet or while standing in water.
3. Do not use this product near water (for example, near a
bath tub, kitchen sink, or swimming pool).
4. Do not allow anything to rest on the power cord. Place
the power cord so that it will not be walked on.
5. Never insert objects of any kind into the product vents
as that may result in fire or electric shock.
34
General information
6. Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
7. Do not disassemble this product. If service or repair
work is required, contact the customer service helpline
found in this user's Guide.
8. Do not overload wall outlets and extension cords.
9. Avoid using during an electrical storm. Use a surge
protector to protect the equipment.
10. Do not use this phone to report a gas leak, especially if
you are in the vicinity of the gas line.
CAUTION
To reduce the risk of fire, use only the supplied power
adaptor.
Unplug this cordless phone immediately
from an outlet if:
• The power cord or plug is damaged or frayed.
• Liquid has been spilled on the product.
• The product has been exposed to rain or water. Do not
retrieve the handset or base until after you have
unplugged the power and phone from the wall. Then
retrieve the unit by the unplugged cords.
• The product has been dropped or the cabinet has been
damaged.
• The product exhibits a distinct change in performance.
General information
Installation Guidelines
1. Read and understand all instructions and save them for
future reference.
2. Follow all warnings and instructions marked on the
product.
3. Do not install this product near a bath tub, sink, or
shower.
4. Operate this phone using only the power source that is
indicated on the marking label. If you are unsure of the
power supply to your home, consult with your dealer or
local power company.
5. Do not place this product on an unstable cart, stand, or
table. This product may fall, causing serious damage to
the product.
6. Adjust only those controls that are covered by the
operating instructions. Improper adjustment of other
controls may result in damage and will often require
extensive work to restore the product to normal
operation.
7. Clean this product with a soft, damp cloth. Do not use
chemicals or cleaning agents to clean this phone.
8. Use only the power supply that came with this unit.
Using other power supplies may damage the unit.
9. Because this phone operates on electricity, you should
have at least one phone in your home that could operate
without electricity in the case the power in your home
goes out.
35
10. To avoid interference to nearby appliances, do not place
the base of the phone on or near a TV, microwave oven,
or VCR.
Battery Safety Instructions
• Do not burn, disassemble, mutilate, or puncture the
battery. The battery contains toxic materials that could be
released, resulting in injury.
CAUTION
There is a risk of explosion if you replace the battery with an
incorrect battery type. Use only the battery pack that came
with your phone or an authorized replacement
recommended by the manufacturer.
• Keep battery packs out of the reach of children.
• Remove battery packs if storing over 30 days.
• Do not dispose of battery packs in fire, which could result
in explosion.
• The rechargeable battery packs that power this product
must be disposed of properly and may need to be
recycled. Refer to your battery’s label for battery type.
Contact your local recycling center for proper disposal
methods.
SAVE THESE INSTRUCTIONS
36
Cleaning
• Clean the handset and base (or charger) with a damp
(not wet) cloth, or an anti-static wipe.
• Never use household polish as this will damage the
product. Never use a dry cloth as this may cause static
shock.
Environmental
• Do not expose to direct sunlight.
• The handset may become warm when the batteries are
being charged or during prolonged periods of use. This is
normal. However, we recommend that to avoid damage,
do not place the product on antique/veneered wood.
• Do not place your product on carpets or other surfaces
which generate fibres, or place it in locations preventing
the free flow of air over its surfaces.
• Do not submerge any part of your product in water and
do not use it in damp or humid conditions, such as
bathrooms.
• Do not expose your product to fire, explosives or other
hazardous conditions.
• There is a slight chance that your phone could be
damaged by an electrical storm. We recommend that you
unplug the power and telephone line cord during an
electrical storm.
General information
Product disposal instructions
Product disposal instructions for residential users
When you have no further use for it, please remove any
batteries and dispose of them and the product according to
your local authority’s recycling processes. For more
information, please contact your local authority or the retailer
where the product was purchased.
Product disposal instructions for business users
Business users should contact their suppliers and check the
terms and conditions of the purchase contract and ensure
that this product is not mixed with other commercial waste
for disposal.
Consumer Products and Accessories
Warranty
Thank you for purchasing this Motorola branded product
manufactured under license by Suncorp Technologies
Limited, 3001-3005 China Resources Building, 26 Harbour
Road, Wan Chai, Hong Kong. ("Suncorp")
What Does this Warranty Cover?
Subject to the exclusions contained below, SUNCORP
TECHNOLOGIES LTD. warrants that this Motorola branded
product ("Product") or certified accessory ("Accessory") sold
for use with this product that it manufactured to be free from
defects in materials and workmanship under normal
consumer usage for the period outlined below. This Limited
Warranty is your exclusive warranty and is not transferable.
General information
Who is covered?
This warranty extends only to the first consumer purchaser,
and is not transferable.
What will SUNCORP TECHNOLOGIES LTD do?
SUNCORP TECHNOLOGIES LTD or its authorized distributor
at its option and within a commercially reasonable time, will at
no charge repair or replace any Products or Accessories that
does not conform to this limited warranty. We may use
functionally equivalent reconditioned/ refurbished/ pre-owned
or new Products, Accessories or parts.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, OTHERWISE THE REPAIR OR
REPLACEMENT PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF
THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OF IMPLIED. IN NO
EVENT SHALL MOTOROLA OR SUNCORP
TECHNOLOGIES LTD BE LIABLE, WHETHER IN
CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR
DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES
37
OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS
OF BUSINESS, LOSS OF INFORMATION OR OTHER
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE
PRODUCTS OR ACCESSORIES TO THE FULL EXTENT
THESE DAMAGES MAY BE DISCLAIMED BY LAW.
Some jurisdictions do not allow the limitation or exclusion of
incidental or consequential damages, or limitation on the
length of an implied warranty, so the above limitations or
exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that
vary from one jurisdiction to another.
Products Covered
Consumer Products
Length of Coverage
One (1) year from the date of
the products original purchase
by the first consumer purchaser
of the product.
Consumer Accessories Ninety (90) days from the date
(battery, power supply(s) of the accessories original
and line cords)
purchase by the first consumer
purchaser of the product.
Consumer Products and The balance of the original
Accessories that are
warranty or for ninety (90)
Repaired or Replaced
days from the date returned to
the consumer, whichever is
longer.
38
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are
excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls
below 80% of their rated capacity and batteries that leak are
covered by this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or
neglect, such as physical damage (cracks, scratches, etc.)
to the surface of the product resulting from misuse; (b)
contact with liquid, water, rain, extreme humidity or heavy
perspiration, sand, dirt or the like, extreme heat, or food; (c)
use of the Products or Accessories for commercial purposes
or subjecting the Product or Accessory to abnormal usage or
conditions; or (d) other acts which are not the fault of
Motorola or SUNCORP TECHNOLOGIES LTD., are
excluded from coverage.
Use of Non-Motorola branded Products and
Accessories. Defects or damage that result from the use of
Non-Motorola branded or certified Products or Accessories
or other peripheral equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or
damages resulting from service, testing, adjustment,
installation, maintenance, alteration, or modification in any
way by someone other than Motorola, SUNCORP
General information
TECHNOLOGIES LTD. or its authorized service centers, are
excluded from coverage.
Technical Information
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola branded housings, or parts,
are excluded from coverage.
All items of telephone equipment have a Ringer Equivalence
Number (REN), which is used to calculate the number of
items which may be connected to any one telephone line.
Your O1 has a REN of 1. A total REN of 4 is allowed. If the
total REN of 4 is exceeded, the telephones may not ring.
With different telephone types, there is no guarantee of
ringing, even when the REN is less than 4.
Communication Services. Defects, damages, or the failure
of Products or Accessories due to any communication
service or signal you may subscribe to or use with the
Products or Accessories is excluded from coverage.
How to Obtain Warranty Service or Other
Information?
To obtain service or information, please call: (65) 68412668.
Email: support@alcom.com.sg
You will receive instructions on how to ship the Products or
Accessories at your expense and risk, to a SUNCORP
TECHNOLOGIES LTD Authorized Repair Center.
To obtain service, you must include: (a) the Product or
Accessory; (b) the original proof of purchase (receipt) which
includes the date, place and seller of the Product; (c) if a
warranty card was included in your box, a completed
warranty card showing the serial number of the Product; (d)
a written description of the problem; and, most importantly;
(e) your address and telephone number.
General information
How many telephones can I have?
Any additional handsets and chargers that you register have
a REN of 0.
Connecting to a switchboard
This product is intended for use within Singapore for
connection to the public telephone network.
Inserting a pause
With some switchboards, after dialling the access code you
may have to wait for a moment while the switchboard picks
up an outside line so you will need to enter a pause in the
dialing sequence.
Press and hold u to insert a pause (P) before entering the
telephone number.
You may also need to enter a pause when storing
international numbers or charge card numbers.
39
Recall
You may need to use the recall function if you are connected
to a switch. Contact your PABX supplier for further
information.
12. Wall mounting
Important
Before you wall-mount your O1, check that you are not
drilling into any hidden wiring or pipes.
Before you drill, make sure the power and telephone line
cables will reach the sockets.
1. Use the following templates to mark the drilling locations.
• To wall-mount the base, drill two holes in the wall 4.9cm
apart horizontally using an 8mm drill bit.
40
Wall mounting
• To wall-mount the charger, drill two holes in the wall
3.0cm apart horizontally using an 8mm drill bit.
2. Insert the wall plugs if necessary, then insert the screws
leaving about 5mm protruding from the wall on which to
hang the phone.
3. Pull the base/charger out of the stand and slot the holes
on the back of the base over the screw heads and
gently pull the base/charger down to make sure it is
securely in place.
Wall mounting
41
Declaration of Conformity (DoC)
multi-handset versions.
Motorola
O101, O102, O103 and O104
DECT phone without telephone answering machine (O10x) and their
Suncorp declares that the following products:
Brandname:
Type:
Descriptions:
to which this declaration related is in conformity with the essential requirements of the following
Ecodesign Directive (2005/32/EC)
R&TTE Directive (1999/5/EC)
directives of the Council of the European Communities:
-
Safety:
EMC:
EN301406 v1.5.1
EC No 278/2009, 6 April 2009
EN60950-1:2006+A11:2009
EN301489-1 v1.8.1 and EN301489-6 v1.3.1
The products are compliant with the following standards:
RF Spectrum:
Ecodesign:
2010.12.21
Norman Tse 20:04:48
+08'00'
21st December 2010
3001-3005 China Resources Building, 26 Harbour Road,
Wanchai, Hong Kong
Norman Tse – Senior Engineering Manager
For and on behalf of Suncorp Technologies Limited,
Signature:
Printed name & Position:
Date:
Place:
Manufactured, distributed or sold by Suncorp
Technologies Ltd. , official licensee for this product.
MOTOROLA and the Stylized M Logo are
trademarks or registered trademarks of Motorola
Trademark Holdings, LLC. and are used under
license. All other trademarks are the property of
their respective owners.
© 2011 Motorola Mobility, Inc. All rights reserved.
Version 5 (SG)
Download PDF