Samsung AH68-01633B User`s manual

Samsung AH68-01633B User`s manual
SAMSUNG ELECTRONICS AMERICA INC.
105 CHALLENGER ROAD, RIDGEFIELD PARK,
NJ 07660 U.S.A.
US
FOR YOUR NEAREST SAMSUNG
SERVICE CENTER
DIAL 1-800-SAMSUNG
AH68-00856C
Precautions
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Precautions
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates “dangerous voltage” inside the product
that presents a risk of electric
shock or personal injury.
This symbol indicates important
instructions accompanying the
product.
CAUTION: DVD PLAYERS USE AN INVISIBLE LASER BEAM WHICH CAN
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE PLAYER CORRECTLY AS INSTRUCTED.
CAUTIONS
Caution: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Attention: Pour éviter les chocs électriques, introduíre la lame la plus large de la fiche dans
la borne correspondante de la prise et pousser jusqu au fond.
This product satisfies FCC regulations when shielded cables and connectors are used to
connect the unit to other equipment. To prevent electromagnetic interference with electric
appliances, such as radios and televisions, use shielded cables and connectors for
connections.
FCC NOTE (for U.S.A):
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect this equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This class B digital apparatus meets all requirements of the Canadian Interference -Causing Equipment Regulations.
CLASS 1
LASER PRODUCT
KLASSE 1
LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1
2
LASER APPARAT
WARNING
CAUTION
To reduce the
risk of fire or
shock hazard, do
not expose this
DVD player to
rain or moisture.
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER
AND DO NOT REPAIR YOURSELF. REFER SERVICING TO
QUALIFIED PERSONNEL.
Note:
• This unit can be used only where the power supply is AC 120V, 60Hz. It cannot be used
elsewhere.
• This DVD player is designed and manufactured to respond to the Region Management
Information. If the Region number of a DVD disc does not correspond to the Region
number of this DVD player, the DVD player cannot play the disc.
• This device is protected by U.S. patent numbers 4,631,603, 4,577,216 and 4,819,098
and other intellectual property rights. The use of Macrovision’s copy protection technology in the device must be authorized by Macrovision and is intended for home and other
limited pay-per-view uses only, unless otherwise authorized in writing by Macrovision.
Reverse engineering or disassembly is prohibited.
Handling Cautions
• Before connecting other components to this player, be sure to turn them all off.
• Do not move the player while a disc is being played, or the disc may be scratched or broken, and the player’s internal parts may be damaged.
• Do not put a flower vase filled with water or any small metal objects on the player.
• Be careful not to put your hand into the disc tray.
• Do not place anything other than the disc in the disc tray.
• Exterior interference such as lightning and static electricity can affect normal operation of
this player. If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The player will
operate normally.
• Be sure to remove the disc and turn off the player after use.
• Disconnect the AC power cord from the AC outlet when you don’t intend to use the player
for long periods of time.
• Clean the disc by wiping in a straight line from the inside to the outside of the disc.
Disc Storage
Be careful not to harm the disc because the data on these discs is highly vulnerable to the
environment.
• Do not keep under direct sunlight.
• Keep in a cool ventilated area.
• Store vertically.
• Keep in a clean protection jacket.
Maintenance of Cabinet
For safety reasons, be sure to disconnect the AC power cord from the AC outlet.
• Do not use benzene, thinner, or other solvents for cleaning.
• Wipe the cabinet with a soft cloth.
3
About Discs
General Features
Discs you can play
Digital video discs
5" and 31/2", single or double sided, single or dual layer. DVDs are
high density optical discs on which high quality picture and audio
are recorded.
Video CDs
5" and 31/2" (with or without playback control).
Screen
Video with MPEG-2 compression
technology. Both regular and
widescreen(16:9) pictures can be
viewed.
Audio CDs
5" and 31/2"
NUON interactive DVD software
Slow Motion
An important scene can be viewed in
slow motion.
Disc Functions
Functions and information available on the DVDs (titles, chapters, subtitles, ratings, multi
angles and more) may differ from disc to disc.
• When
appears on screen, it indicates an invalid button press.
Discs that cannot be played
CD-I, CD-ROM, DVD-ROM, DVD-RAM discs cannot be played in this unit.
CD-G can play audio only, not graphics.
Region code
~
Excellent Sound
Dolby Digital, a technology
developed by Dolby Laboratories
provides crystal clear sound
reproduction.
Your DVD player is designed and manufactured to respond to the
region management information that is recorded on a DVD disc.
COPY PROTECTION
• Many DVD discs are encoded with copy protection. Because of this, you should
only connect your DVD player directly to your TV, not to a VCR. Connecting to a
VCR results in a distorted picture from copy-protected DVD discs.
• This product incorporates copyright protection technology that is protected by methods
claims of certain U.S. patents and other intellectual property rights owned by the
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by the Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
DVD-N501
Lock
The parental control allows users to set
the level necessary to prohibit children
from viewing harmful movies such as
those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various
languages(Audio/Subtitle) and screen
angles while enjoying movies.
Repeat
You can repeat a song or movie simply
by pressing the REPEAT button.
MP3
This unit can play discs created from
MP3 files.
HDCD
This unit can play HDCD(High Definition
Compact Discs). These discs have a
higher sampling rate than regular CDs
which contributes to better sound.
NOTE
* To ensure proper playback of discs burned from MP3 files, make sure the files have been recorded
at a bit rate of at least 128kbps.
* If there are any gaps (blank data) on multi-session discs, you may experience playback problems.
* On discs that are recorded with a Variable Bit Rate(VBR), e.g. from 32 to 320 kbps, the sound may
cut in and out.
* HDCD®, High Definition Compatible Digital ® and Pacific MicrosonicsTM are either registered trademarks
or trademarks of Pacific Microsonics, Inc. in the United States and/or other countries. HDCD system man
ufactured under license from Pacific Microsonics, Inc. This product is covered by one or more of the fol
lowing: In the USA: 5,479,168, 5,638,074, 5,640,161, 5,808,574, 5,838,274, 5,854,600, 5,864,311,
5,872,531, and in Australia: 669114. Other patents pending.
Disc Markings
~
• Play
Region
Number
NTSC
• NTSC broadcast
system in U.S.A,
Canada, Korea,
Japan, etc.
• Dolby
Digital disc
STEREO
DIGITAL
SOUND
• Stereo disc
• Digital
Audio disc
• DTS disc
Play Region Number
Both the DVD player and the discs are coded by region. These regional codes must match in order for the
disc to play. If the codes do not match, the disc will not play.
4
The Region Number for this player is described on the rear panel of the player.
5
Before You Start
TABLE OF CONTENTS
Accessories
SETUP
Description-Front Panel............................8
Description-Rear Panel ............................9
Tour of the Remote Control ................... 1 0
Remote Control
User’s Manual
Choosing a Connection ......................... 12
• Connection to an Audio System ..........12
• Connection to a TV ..............................13
Using the Menu ..................................14
Setting Up the Language Features .......15
Setting Up the Movie ..............................17
Setting Up the Audio ..............................18
Setting Up the Video ..............................19
Setting Up the Lock ................................20
Playing a Disc ....................................21
Search & Skip .................................................23
Repeat A-B & 3D Sound................................24
Bookmark.........................................................25
TM
MediaMacro Zoom & Pan ......................26
TM
ActionCapture Strobe ...........................27
TM
AngleView Display & Screen Fit............28
Selecting the Audio Language ...............29
Selecting the Subtitle Language ............30
Display....................................................31
Digest Play .............................................32
PLAY
Install Batteries in the Remote
1 Open the battery cover on the back of the remote.
CONNECTIONS
Video/Audio Cable
Batteries for
Remote Control
(AA Size)
2 Insert two AA batteries. Make sure that the polarities (+ and -) are
aligned correctly.
SPECIALS
3 Replace the battery cover.
V.L.M. & Gaming ....................................33
MP3 play ...............................................34
REFERENCE
If remote doesn’t operate properly:
• Check the polarity + - of the batteries (Dry-Cell)
• Check if the batteries are drained.
• Check if remote sensor is blocked by obstacles.
Remote Control Setting ..........................35
Troubleshooting Guide ...........................36
Specifications .........................................37
Warranty .................................................39
• Check if there is any fluorescent lighting nearby.
7
Description-Front Panel
Description-Rear Panel
SETUP
1
2
3
4
56 7 8
9
Front Panel Controls
1 STANDBY/ON
5
• When the unit is first plugged in,
this indicator lights.
6
2 NUON PORTS
• Allow you to plug in a joystick or other
peripherals.
3 DISPLAY
7
• Operation indicators are displayed here.
4 DISC TRAY
8
• Press OPEN/CLOSE to open and close
the disc tray.
9
2
5
6 7
OPEN/CLOSE
• Press to open and close the disc tray.
SCREEN FIT
• Allows you to eliminate the black bars
of the screen and fill any TV screen
completely with the picture.
PLAY/PAUSE
• Begin or pause disc play.
STOP
• Stops disc play.
SKIP
• Use to skip chapters or tracks.
8
9
1
2
3
4
5
Rear Panel Jacks
1 DIGITAL AUDIO OUT JACK
• Use an optical or coxial digital cable to connect to a compatible Dolby Digital receiver.
Use to connect to an A/V Amplifier that contains a Dolby Digital decoder or DTS decoder.
10
2 ANALOG AUDIO OUT JACKS
• Connect to the Audio input jacks of your television, audio/video receiver, or VCR.
11
12
1
3 4
14
13
Front Panel Display
1
2
3
4
5
6
7
8
9
10
11
8
Angle indicator. You can select
multiple angles of a scene recorded
by different cameras.
Disc type indicators
Reverse play / Pause / Forward play
Lights when 3D surround is turned on.
Title number
Chapter number.
Video/Audio CD : Track number
Repeat play mode
Linear PCM audio output
Dolby Digital Audio output
DTS (Digital Theater System) output
12
13
14
MP3 indicator
MPEG-2 Audio output
Displays various messages
concerning operations such as PLAY,
STOP, LOAD, ...
no DISC : No disc loaded.
OPEN : The disc tray is open.
LOAD : Player is loading disc
information.
HDCD : When an HDCD®
recording is detected,
the letters “HDCD” will flash
for about 10 seconds
at the beginning of every
track.
3 VIDEO OUT JACK
• Use a video cable to connect to the Video input jack on your television.
4 S-VIDEO OUT JACK
• Use the S-Video cable to connect this jack to the S-Video jack on your television for
a higher quality picture.
5 COMPONENT VIDEO OUT JACKS
• Use these jacks if you have a TV with Component Video in jacks. These jacks provide Pr,
Pb and Y video. Along with S-Video, Component Video provides the best picture quality.
9
Tour of the Remote Control
Tour of the Remote Control
DVD Function Buttons
17
18
3D SOUND Button
2 NUMBER Buttons
19
OPEN/CLOSE Button
3 STEP Button
• Advances play one frame at a time.
20
CHANNEL Button
21
DIGEST Button(ZOOM IN)
22
PLAY/PAUSE Button
• Begin/Pause disc play
23
SKIP Button
• Use to skip the title, chapter, or track.
24
BOOKMARK Button
• Use to memorize scenes for replay.
25
DISPLAY Button
• Use to see the status of various
settings.
26
AUDIO Button
• Use this button to access various audio
functions on a disc.
4 VOLUME Button
5 TV/VIDEO Button
2
6 ZOOM Button
7 S.FIT Button(ZOOM OUT)
3
4/A
5/B
6
7
8
9
10
11
12
13
14
15
18
8 SEARCH Buttons
• Allows you to search forward/backward
through a disc.
9 STOP Button
19
20/C
10
EXIT Button
• Returns to a previous menu.
21
11
MENU Button
• Brings up the Disc menu.
22
23
24
25
26
27
12
SUBTITLE Button
13
m ANGLE
• Use to access multiple angles
on a DVD.
28
29
30
31
14
DISC MENU Button
15
CLEAR Button
• Use to remove pop-up menus or
status displays from the screen.
16
NUON Button
•Pressing this button brings up a special
NUON menu. When a DVD disc has
enhanced NUON content, you can
navigate and view this extra content by
going to this menu first.
16
32
17
SETUP
1
1 DVD POWER Button
27 ENTER/DIRECTION Button
(UP/DOWN or LEFT/RIGHT Button)
•This button functions as a toggle switch.
28 TOP MENU Button
• Takes you to the menu on the DVD disc
or CD/VCD.
29 REPEAT Button
• Allows you to repeat play a title,
chapter, track, or disc.
30
V.L.M. Button (Virtual Light Machine)
31 REPEAT A-B Button
• Use to mark a segment to repeat
between A and B.
32
TV POWER Button
p STROBE Button
• Shows snapshots of nine successive
frames of the movie as it plays.
You may pause and select one frame.
TV Function Buttons
A
B
10
VOLUME +/- Buttons
TV/VIDEO Selection Button
C
CHANNEL UP/DOWN Buttons
11
Choosing a Connection
Choosing a Connection
The following show examples of connections commonly used to connect
the DVD player with a TV and other components.
Connection to a TV
TV (Normal, Widescreen, Projection, etc..)
Before Connecting the DVD Player
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
• Refer to user’s manual of the components you are connecting for more information on those particular components.
Method 1
Video Input Jack
S-Video Jack
Component
Video Jacks
CONNECTIONS
Audio Input Jacks
Method 3
Method 2
Connection to an Audio System
TV
Method 2
Method 1
S-Video
Cable
AV Cable
2ch Amplifier
Audio Input Jacks
Dolby Digital Decoder
Digital Audio Input Jacks
AUDIO
SYSTEM
OR
Video
Cables
OR
DVD
OR
DVD
PLAYER
Analog Audio Out
12
Digital Audio Out
Basic
Audio
Good
picture
Better
picture
Connection to a TV (For Video)
• Method 1
DVD Player + TV with Video Input Jack
Connection to an Audio System
• Method 2
DVD Player + TV with S-Video Input Jack
• Method 1
• Method 2
• Method 3
DVD Player + TV with Component Video Jacks
DVD Player + 2CH Stereo Amplifier, Dolby Pro Logic Decoder
DVD Player + Amplifier with Dolby Digital Decoder/DTS Decoder
Best picture
13
Using the Menu
The Menu lets you customize your DVD player by allowing you to select various language
preferences, set up a parental control, even adjust the player to the type of television screen
you have.
1
Press the MENU button
on the remote.
• Language
-Setup of the Menu Language.
The language in which you would like to
view your SAMSUNG DVD menus.
• Movie
-Setup of the Movie.
• Audio
-Setup of the Audio.
• Lock
-Setup of the Lock.
-Use to deny playback of discs or scenes with objectionable material.
(Must be supported by the disc.)
• Help
-This menu describes the terms that are displayed on the DVD player.
2
Use the UP/DOWN buttons on the remote to access the different
features.
3
Press the ENTER button to access the sub features.
To make the menu screen disappear after setting up, press the MENU
button again or the EXIT button twice.
NOTE
• Not all Menu selections will work - this is dependent on the DVD disc content. For example,
the subtitle menu option will not have any effect on a disc that does not have subtitle support.
If you set the player menu, disc menu, audio and Subtitle language in advance, they will come
up automatically every time you watch a movie.
Using the Player Menu Language
1
2
3
Press the MENU button.
4
5
Press the ENTER button.
6
Press the ENTER button.
Press the ENTER button.
Use the UP/DOWN buttons to
select the Player Menu
Language.
Use the LEFT/RIGHT buttons to
select ‘English’.
-English is selected and the screen
returns to the language submenu.
7
Press the EXIT button twice or
the MENU button, and the
menu screen will disappear.
PLAYBACK
• Video
-Setup of the Video.
Setting Up the Language Features
Using the Disc Menu Language
This function changes the text language on the disc menu screens.
1
2
3
Press the MENU button.
4
5
Press the ENTER button.
6
7
Press the ENTER button.
Press the ENTER button.
Use the UP/DOWN buttons to
select the Disc Menu Language.
Use the LEFT/RIGHT buttons
to select ‘Language’.
Press the EXIT button twice or
the MENU button, and the menu
screen will disappear.
• Once each menu is selected, its submenus will appear on the right of the screen.
Move the TOGGLE button to left, and the submenus that are displayed on the right of the
screen will disappear.
14
15
Setting Up the Language Features
Using the Preferred Subtitle
1
2
3
Press the MENU button.
4
5
Press the ENTER button.
ex) Setting up in English.
Press the UP/DOWN buttons
to select Preferred Subtitle.
1
2
Press the MENU button.
3
4
Press the ENTER button.
Use the UP/DOWN or
LEFT/RIGHT buttons to
select ‘English’.
-Use to enter the time from which you
want to start.
• Title
-Use to select a title number.
of language menu returns.
-A DVD may contain several different titles.
For example, if a disc contains four
different movies, each might be considered a title.
Press the EXIT button twice or the
MENU button, and the menu
screen will disappear.
1
2
3
Press the MENU button.
4
5
Press the ENTER button.
PLAYBACK
Press the ENTER button.
• Chapter
-Use to select a chapter number.
-Each Title on a DVD can be divided into chapters
(similar to tracks on an audio CD).
Using the Preferred Audio
ex) Setting up in English.
Use the NUMBER buttons to enter
the desired Time, Title or Chapter.
• Time
6 - English is selected and then the submenu
7
Press the UP/DOWN buttons to
select to Movie.
ex) Setting up in English.
- Select “Automatic” if you want the
subtitle language to be the same as
the language selected as the audio
preference.
NOTE
• If the selected language is not recorded
on the disc, the original pre-recorded
language is selected.
Press the ENTER button.
Setting up the Movie
• Angle
Press the ENTER button.
-See page 28.
Press the UP/DOWN buttons
to select Preferred Audio.
• Available Subtitle
-See page 30.
Use the UP/DOWN or
LEFT/RIGHT buttons
to select ‘English’.
- Select “Original” if you want the default
soundtrack language to be the original
language the disc is recorded in.
• Available Audio
-See page 29.
5
Press the EXIT button twice or
the MENU button, and the menu
screen will disappear.
the ENTER button.
6 - Press
English is selected and then the submenu
of language menu returns.
7
16
Press the EXIT button twice or the
MENU button, and the menu
screen will disappear.
17
Setting Up the Audio
Setting Up the Video
1
2
Press the MENU button.
Use the UP/DOWN buttons to
select Audio. Press the ENTER button.
Use the UP/DOWN buttons to
3 select
the desired item.
1
2
Press the MENU button.
3
Use the UP/DOWN buttons to
select the desired item.
Press ENTER.
4
Use the LEFT/RIGHT button to
select the desired item. Press the ENTER button.
Press the ENTER button.
4
• Digital Output
Use the LEFT/RIGHT button to
select the desired item.
Press the ENTER button.
Use the UP/DOWN buttons to
select Video, then press the
ENTER button.
• TV Aspect
- PCM : Converts to PCM (2CH) 48KHz/16Bit audio.
Select PCM when using the Analog Audio Outputs.
Depending on the type of television you have, you may want to adjust
the screen setting (aspect ratio).
- Letter Box :
- Bitstream : Converts to Dolby Digital Bitstream (5.1CH).
Select Bitstream when using the Digital Audio Output.
• LPCM 96 KHz · 48 KHz (ON/OFF)
PLAYBACK
Select when you want to see the total 16:9 ratio screen DVD
supplies, even though you have a TV with a 4:3 ratio screen.
Black bars will appear at the top and bottom of the screen.
- Pan-Scan :
- For discs recorded with 96 KHz Linear PCM, you must change 96KHZ(Off) to
48KHz(On) for analog and digital output.
PCM won’t be output when it is set to LPCM 96 KHz.
Select this for conventional size TVs when you want to see the
central portion of the 16:9 screen. (Extreme left and right side of
movie picture will be cut off.)
• DTS
- Wide :
- On : Outputs DTS Bitstream via digital output only. Select DTS when connecting to
a DTS Decoder.
You can view the full 16:9 picture on your widescreen TV.
- Off : Doesn’t output DTS signal.
• Screen Fit
- You can view your picture either letter boxed(with bars), or stretch the picture
to fit the screen.
• Dynamic Compression
- On : To select dynamic compression.
- Off : To select the standard range.
• Black Level
- Adjusts the brightness of the screen.(On/Off)
• Analog 2X Scan Audio
- On : Turns analog 2X scan audio on.
2X Scan Audio does not work using the digital output.
• Front Display
Adjust the brightness of the unit’s front panel display.
- Off : Turns analog 2X scan audio off.
- Bright : Makes the Front Panel Display bright.
- Dim : Makes the Front Panel Display dim.
- Auto : Makes the Front Panel Display dim automatically when playing a DVD.
5
18
Press the EXIT button twice or the MENU button again,
and the MENU screen will disappear.
19
Setting Up the Lock
Playing a Disc
The Parental Control function works in conjunction with DVDs that have
been assigned a rating - which helps you control the types of DVDs that
your family watches. There are up to 8 rating levels on a disc.
Play
1
Setting the Rating Level
1
2
3
Press the MENU button.
Press the UP/DOWN buttons
to select LOCK, then press the
ENTER button.
2
3
4
Press the OPEN/CLOSE button.
The STANDBY indicator light goes out and the tray opens.
Place a disc gently into the tray with the disc’s label facing up.
Press the PLAY/PAUSE button to start play.
Press the STOP button to stop play.
Use the UP/DOWN buttons to
select Enter Password.
RESUME function
Press the ENTER button and
enter your 4-digit password
by pressing the 0-9 button.
5
Use the UP/DOWN buttons to
select Rating Level and press
the ENTER button.
6
Use the UP/DOWN or LEFT/
RIGHT buttons to choose a
Rating Level, then press ENTER.
When you stop disc play, the player remembers where you stopped, so when you press
PLAY again, it will pick up where you left off (unless the disc is removed, the STOP button
is pressed twice or the player is unplugged.).
PLAYBACK
4
- For example, if you choose Level 7,
the disc which contains LEVEL 7 or 8 will
now not play.
- The default password is '9999'.
7
Press the EXIT button twice or the
MENU button, and the menu screen
will disappear.
NOTE
• To change your password, press the Up/Down buttons and select 'Change Password'
from the LOCK menu.
• Changing password is possible only when the password has been entered.
20
NOTE
• If the player is left for 5 minutes in pause mode, it will stop.
• The power is automatically turned off after approximately 30 minutes have elapsed in
the stop mode (auto power-off feature).
• If the player is left in stop mode for more than one minute without any user interaction, a
screen saver will be activated.
• This
icon indicates an invalid button press.
21
Playing a Disc
Stop
Press the STOP button during play.
Search & Skip
Searching a Chapter/Track
Searching is not restricted to within a "chapter" or "track".
Press the FWD or REV SEARCH button on the remote control during play.
Remove
Press the OPEN/CLOSE button.
Pause
Press the PLAY/PAUSE or STEP button on the remote during play.
Pause
Press the PLAY/PAUSE or STEP button on the remote during play.
• Screen stops, no sound.
• To resume, press the PLAY/PAUSE button once again.
• Each time the button is pressed, a new frame will appear.
• No sound is heard during STEP mode.
• Press PLAY/PAUSE to resume normal play.
(You can only perform step motion play in the forward direction.)
Skipping Chapter/ Tracks
The skip function allows you to "skip" from one chapter to another in the forward or
reverse direction.
Press the NEXT SKIP or BACK SKIP button during play.
PLAYBACK
Step Motion (Except CD)
Press the STEP button on the remote during play.
• Press the REVERSE or FORWARD SEARCH button on the remote and press again to
search at a faster speed(2X/4X/8X/16X/32X/64X/128X, in order) on the DVD.
• Press the REVERSE or FORWARD SEARCH button on the remote and press again to
search at a faster speed(2X/4X/8X/16X/32X) on VCD and CD.
• To return to normal speed play, press the PLAY/ PAUSE button.
• When playing a DVD, if you press the NEXT SKIP button, it moves to the next chapter.
If you press the BACK SKIP button, it moves to the beginning of the chapter. One more
press makes it move to the beginning of the previous chapter.
• When playing a VCD or a CD, if you press the NEXT SKIP button, it moves to the next
track. If you press the BACK SKIP button, it moves to the the beginning of the track.
One more press makes it move to the beginning of the previous track.
Slow Motion (Except CD)
Press the FWD or REV SEARCH button on the remote during PAUSE
or STEP mode.
• By pressing or shuttling, you can select slow motion playback for 1/2, 1/4 or 1/8 of
normal speed.
• No sound is heard during slow mode..
• When playing a VCD, reverse slow motion playback will not work.
NOTE
• When in search mode (4X/8X/16X/32X/64X/128X) on a DVD or high-speed playback
(4X/8X/16X/32X) on a VCD, no sound will be heard.
• Depending on the disc, audio may not be heard when a disc is in 2X playback mode.
22
23
Repeat A-B & 3D Sound
Bookmark
The Bookmark function lets you select parts of a DVD or VCD so that you can quickly find
Repeat A-B
the section at a later time.
The Repeat A-B function lets you mark a segment to repeat between the beginning (A) and
the end (B) of the segment you want to review.
1
Press the REPEAT A-B button at
the beginning (A) of the segment
you want to review.
2
Press the REPEAT A-B button
again or the ENTER button at the
end (B) of the segment you want
to review.
3
Press the ENTER button to view
the set segment A->B. Then, the
segment will begin repeating.
4
To clear Repeat A-B, press
the REPEAT A-B button again.
The simulated surround effect (SPATIALIZER N-2-2) depends on the disc contents. If you
connect the unit to your stereo system, you can enhance sound quality and produce a
greater surround effect. This feature is useful when you are using the DVD player with a two
channel stereo through the analog outputs.
(Discs which are recorded with DTS will not work. When the Digital Output is set to Bitstream
in the MENU, the 3D Sound function will not work.)
1
Press the 3D SOUND button
on the remote. (Be sure the
Digital Output is set to PCM.)
2
Use the UP/DOWN buttons to
select 3D sound On/Off.
NOTE
• The Repeat A-B function works on the same title or track.
• If the title or track is completed before marking the end (B), the end of the title or track
becomes B automatically.
• Depending on the disc, the Repeat A-B and 3D Sound functions may not work.
• 3D sound will not operate in V.L.M (Virtual Light Machine) mode.(CD-DA, MP3, etc.)
• All the pop-up menus (except Repeat A-B) automatically disappear five seconds later.
24
To store a Bookmark
1
2
Use the LEFT/RIGHT button to move to the desired bookmark.
3
Press the BOOKMARK button to turn off the display.
When you reach the scene you want to mark, press the ENTER
button. The icon will change to a number (1, 2, or 3).
PLAYBACK
3D Sound
During playback, press the BOOKMARK button on the remote. A
‘BOOKMARK’ will be displayed.
To recall a Bookmarked scene
1
2
3
During playback, press the BOOKMARK button on the remote.
Use the LEFT/RIGHT button to select a marked scene.
Press the PLAY/PAUSE button to skip to the marked scene.
To clear a Bookmark
1
2
During playback, press the BOOKMARK button on the remote.
3
Press the CLEAR button to delete a bookmark number.
Press the BOOKMARK button to turn off display.
Use the LEFT/RIGHT button to select the bookmark number you
want to delete.
NOTE
• Up to three scenes may be marked at the same time.
• Depending on the disc, the Bookmark function may not work.
25
MediaMacro
TM
ActionCapture
Zoom & Pan
TM
Strobe
MediaMacroTM Zoom & Pan
ActionCaptureTM Strobe
For DVDs, VCDs
This function allows complete control over what part of the picture you want to see.
You can select any portion of the screen and magnify that portion up to 15 times.
This unique strobe function takes snapshots of a continuous motion, then displays
these snapshots in order. This is a useful for analyzing golf swings, a pianist's finger
movements or even a pitcher's technique.
the ZOOM button on the
1 Press
remote control, and the Zoom
screen appears on the upper
right corner of the screen.
2
Press the DIGEST and S-FIT
buttons for Zoom IN/OUT.
3
Press the ZOOM button again
to exit.
Zoom In
Press the P-STROBE button,
and the screen will be divided
into nine subscreens.
2
Press the PLAY button, and the
current progressing subscreen
is highlighted in yellow.
3
Use the TOGGLE
(UP/DOWN/LEFT/RIGHT) button
to move the highlight.
4
Press the ENTER button,
and the highlighted subscreen
becomes a still screen.
To return to the P-strobe status,
press the P-STROBE button.
5
Press the P-STROBE button
again for normal play.
m
PLAYBACK
1
Zoom Out
NOTE
• Use the DIRECTION (UP/DOWN/LEFT/RIGHT) button to move the zoom picture.
26
27
AngleView
Using the
m
TM
Selecting the Audio Language
Display & Screen Fit
You can select a desired language quickly and easily with the AUDIO button.
ANGLE Button
The DVD-N501 displays each angle in a portion of the screen, allowing you to select any
angle at the touch of the remote.
Press the ANGLE button to see if an
‘ANGLE (
)’ mark is present in the
upper right hand corner of the screen.
1
Example) If there are 6 angles available
2
When an ‘ANGLE’ mark is
shown, press the m ANGLE
button.
Using the AUDIO Button
1
Press the AUDIO button on
the remote.
2
Use the UP/DOWN buttons to
select the desired Audio
language on a DVD.
- The audio and subtitle languages
are represented by abbreviations.
Use the LEFT/RIGHT/UP/
DOWN buttons to select the
desired screen angle.
Then press the ENTER button.
NOTE
• This function does not work when a DVD has not been recorded with a multi-camera
angle system.
Screen Fit
Press the SCREEN FIT button on the remote or the front panel.
Screen Fit - Off
Screen Fit - On
NOTE
Press the SCREEN FIT(or S-FIT) button on remote control.
- Allows you to eliminate the black bars in the top and bottom of the screen when a
movie is playing in the Widescreen format(16:9).
NOTE
• Depending on the disc, the ActionCaptureTM Strobe and Screen Fit functions may not work.
28
29
SPECIALS
• This function depends on what languages are encoded on the disc and may not work
with all DVDs.
• A DVD disc can contain up to 8 audio languages.
• How to have the same audio language come up whenever you play a DVD;
Refer to “Setting Up the Language Features” on page 16.
Selecting the Subtitle Language
You can select a desired subtitle quickly and easily with the SUBTITLE button.
Display
When the user presses the DISPLAY button while playing a DVD, he will see the display
screen that shows the status of various settings.
Using the SUBTITLE Button
1
2
3
4
Press the SUBTITLE button.
Use the UP/DOWN buttons to
select the desired subtitle
language.
Press the ENTER button.
Use the UP/DOWN buttons to
determine whether or not the
subtitle will be displayed.
- Initially, the subtitling will not appear
on screen.
- The audio and subtitle languages are
represented by abbreviations.
5
Press the EXIT button twice or
the MENU button again,
and the MENU screen will
disappear.
1
Press the DISPLAY button.
• Time
• Title
• Chapter
• Subtitle
• Audio
• Lock
• Screen Fit
• Repeat
NOTE
• Bookmark
• Angle
SPECIALS
• This function depends on what languages are encoded on the disc and may not work
with all DVDs.
• A DVD disc can contain up to 32 subtitle languages.
• Repeat A-B
• 3D Sound
NOTE
• You cannot change settings in the Display menu.
• Press either the DISPLAY button or EXIT button, and the Display screen disappears.
30
31
Digest Play
V.L.M.
& Gaming & NUON
Virtual Light Machine
Digest Play
1
During play, press the DIGEST
button.
- You'll see the 6 individual windows
representing each of the chapters
on the TV screen.
- When each window is displayed, the first
3 seconds of the chapter will be played.
2
- V.L.M. is a series of stunning and incredibly fun visual effects that are 'synchronized' to the
music being played.
Press the UP/DOWN/LEFT/RIGHT
button to select the window you'd
like to see, and press the ENTER
button.
The disc will start playing from the
window(chapter) you chose.
- Up to 6 windows(chapters) can be
displayed on the screen at a time.
Press the 'SKIP' button for the next 6
chapters if the movie has more than 6.
skip button
3
1. When a CD-DA or MP3 disc is inserted, the V.L.M. screen is automatically displayed.
2. To switch between the V.L.M. modes (see figure below), press the V.L.M. button,
then the UP/DOWN buttons. Each V.L.M. mode has many settings that can be
accessed by pressing the ENTER and UP/DOWN buttons.
Press the EXIT button twice or the
MENU button again,
and the MENU screen will disappear.
Manual ➛ Chill Out ➛ Techno
➛ Rock/Pop ➛ Classical
Gaming
Your DVD-N501 player, in addition to playing DVD movies, VCD and CD-Audio discs,
also supports a wide variety of NUON entertainment and edutainment software titles.
NUON ports on the front panel allow you to plug in a wide variety of NUON peripherals.
There are two NUON ports on the front panel of your DVD-N501 player.
To play a NUON game, you need to connect a NUON joystick to either of these ports
(or connect multiple NUON joysticks - two supported by the ports on the front panel,
multiple joystick support provided via a NUON splitter that connects to these NUON ports)
and insert the NUON game disc in the tray. Depending on the game disc, you may not
be able to hear audio via the digital audio out jack. If this occurs, you must hook up
the analog outputs to hear NUON game disc audio.
Connect the joystick to one of the ports. Insert the game disc
in the tray.
Press the PLAY/PAUSE button to start playback.
- Samsung DVD-N501 Joystick button Mapping for DVD, VCD, CDDA playback.
Button mapping for NUON depends on the NUON disc. NUON button usage is
different from disc to disc.
- Unplugging and replugging a joystick when playing a game may cause program
disfunction. If this occurs, press POWER on the front panel to re-initalize the program.
NOTE
• 'DIGEST' may not operate depending on the disc in use.
• If the first chapter has no video data, then some of those six chapters may display a black screen.
32
NUON
The default setting of the DVD-N501 is pre-set for NUON mode.
This allows you to enjoy NUON enhanced movies which contain a variety of additional
interactive features not available on a standard DVD player. When playing a regular
DVD movie disc that is not NUON enhanced while the DVD-N501 is in NUON mode,
your player’s performance will not be affected. No set changes are required.
Therefore, we recommend that the default setting for your player be kept in NUON priority.
Pressing the NUON button allows you to switch your player’s default setting between
NUON priority and DVD priority.
33
SPECIALS
1
2
MP3 play
Remote Control Setting
When a MP3 disc is inserted in your DVD player, the disc will be played immediately.
The remote can also be set up to control most TVs. To program the remote, use the code
that corresponds to your brand.
MP3 Play
1
Press the DISC MENU button.
The Disc menu will come up.
1
2
Turn on the TV.
3
While holding the TV POWER
button down, enter the code for
your brand.
TV Codes
Point the DVD’s remote at the
TV.
e.g
2
Use the UP/DOWN buttons to
select the artist you want to hear,
then press the ENTER button.
3
For SAMSUNG _4 TVs
While holding down the TV button, enter 0
then and 1.
4
Select the track you want to hear
by using the UP/DOWN buttons.
If the TV turns off, setup is
complete.
Enter other codes of the same brand
if the first code does not work.
5
TV Codes
To operate the TV, use the “TV
Function Buttons” described on
page 11.
CODE
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
BRAND
SAMSUNG_4
SAMSUNG_6, LG, LOEWE, PHILIPS, FINLUX, YOKO, LOEWE OPTA,
MITSUBISHI, PHONOLA, RADIOLA, SCHNEIDER
SAMSUNG_1
SAMSUNG_2
SAMSUNG_3
SAMSUNG_5
TOSHIBA
PANASONIC_4
GRUNDIG, BLAUPUNKT, SIEMENS
SHARP
HITACHI
SANYO, AKAL, FISHER
HITACHI, SABA, THOMSON, NORDMENDE
HITACHI, NORDMENDE, SABA, TELEFUNKEN, THOMSON, BRANDT,
FERGUSON, PIONEER, TELEAVA
SONY
TOSHIBA, SANYO, SHARP, SONY, MITSUBISHI
TOSHIBA, GRUNDIG, FINLUX
TOSHIBA
TOSHIBA
PHILIPS, PHONOLA, RADIOLA
TOSHIBA, GRUNDIG, CGE, IMPERIAL, MIVAR
PHILIPS, SABA, BANG&OLUFSEN, BRIONVEGA, FINLUX,
FORMENTI, LOEWE OPTA, METZ, WEGA, PHONOLA, RADIOMARELLI,
SINGER, SINUDYNE
NOKIA, PANASONIC, SABA, PIONEER, REZ, SELECO, SALORA
HITACHI, NORDMENDE, PANASONIC, SABA, TELEFUNKEN,
THOMSON, CONTINENTAL, EDISON
PANASONIC_2
PANASONIC_3
PANASONIC_6
TELEFUNKEN
MIVAL
LG_2
SHARP_2
JVC
THOMSON ASIA
THOMSON ASIA
NOTE
NOTE
• Press the DISPLAY button and the detailed
information of the current music will be displayed.
• In case of a MP3 disc, the 2X, 4X, ...... scan modes
do not operate. Only the SKIP button functions so
that track search can operate.
• Folders(also known as directories) contained
in CD-R/RW MP3 disc will be reconized by
the DVD-N501 as an “ALBUM”.
REFERENCE
34
• The remote may not be able to control every model TV of the brands listed.
• Certain audio features of this product manufactured under a license from Desper
Products, Inc. Spatializer® and circle-in-square device are trademarks owned by
DesperProducts, Inc.
• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories. Confidential unpublished works. ©1992-1997 Dolby
Laboratories Inc. All rights reserves
• “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
• VM Labs Legal Notices:
Trademark:“NUONTM” and “VLM” and “Virtual Light MachineTM” are trademarks of VM
Labs. Inc. Copyright: NUON Mediaware, Copyright ©1995-2000, VM Labs, Inc.
All rights reserved.
Patents: This product is covered by one or more claims of certain issued and pending
U.S. Patents and patent applications of VM Labs, Inc. Reverse engineering and
disassembly are prohibited.
• HDCD®, High Definition Compatible Digital ® and Pacific MicrosonicsTM are either
registered trademarks or trademarks of Pacific Microsonics, Inc. in the United States
and/or other countries. HDCD system manufactured under license from Pacific
Microsonics, Inc. This product is covered by one or more of the following: In the USA:
5,479,168, 5,638,074, 5,640,161, 5,808,574, 5,838,274, 5,854,600, 5,864,311, 5,872,
531, and in Australia: 669114. Other patents pending.
35
Troubleshooting Guide
Specifications
Before requesting service (troubleshooting)
Problem
No operations can be
performed with remote.
Disc does not play.
The
icon appears
on screen.
Action
Page
General
• Check the batteries in the remote. May need replacing.
• Operate the remote control at a distance of no more than 20
feet.
• Remove batteries and hold down one or more buttons for
several minutes to drain the microprocessor inside the
remote to reset it. Reinstall batteries and try remote again.
P6
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
• This player cannot play CD-ROMs, DVD-ROMs, CD-R, etc.
Insert a DVD, a VIDEO-CD or a CD.
P4
• The features or action cannot be completed at this time
because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search
time that is out of range.
Power Requirements
Power Consumption
Weight
Dimensions
Operating Temperature Range
Operating Humidity Range
DVD
(DIGITAL VERSATILE DISC)
Disc
P28~30
CD : 5"
(COMPACT DISC)
CD : 31/2"
(COMPACT DISC)
VCD : 5"
Composite Video
Disc Menu doesn’t
appear.
• Check if the disc has a Menu.
P14, 15
Playback mode differs
from the Setup Menu
selection.
• Some of the functions selected in the Setup Menu may not
work properly if the disc is not encoded with the corresponding function.
P16~20
The screen ratio
cannot be changed.
• The Screen Ratio is fixed on your DVDs.
No audio.
• Make sure you have selected the correct Digital Output in
the Audio Options Menu.
Video
Output
Component Video
S-VIDEO
Forgot password
Will not read disc or
other error message.
36
2 Channel
• Press power on from a cold start with no disc in the unit. Press
the STOP and PLAY buttons simultaneously on the front panel
for three seconds. “All setup value will be reset to factory
settings. Your player will be shut off.” will appear. Press the
MENU button on the remote control to select the Parental Mode.
The Parental Mode is now unlocked as indicated on the display.
Press the DOWN button to select Parental. Press ENTER and
the Password Check display will appear. Enter the default password of “9999”. You can now set your rating level and change
your password to a new number.
P18
Output Level
Audio
Output
P20
*Frequency Response
*S/N Ratio
*Dynamic Range
*Total Harmonic Distortion
(L, R)
Analog : 2 Vrms (1 kHz)
Digital : 1.15 Vp-p
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
110 dB
92 dB
0.003 % (In case of 1 KHz)
*: Nominal specification
• Turn the player off and unplug it to reset the DVD player.
Wait approximately 2 minutes, plug the player back in and
turn it on.
• Go to the contents and find the section of the instruction
book that contains the explanations regarding the current
problem, and follow the procedure once again.
• If the problem still cannot be solved, please contact your
nearest authorized service center.
REFERENCE
If you experience other
problems.
P19
AC 120 V, 60 Hz
15W
6.2lbs
16.9(W) x 9.4(D) x 3.1(H)/inch
+41°F to +95°F
10 % to 75 %
Reading Speed : 11.45 ft/sec
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min
Reading Speed : 3.9 to 4.6 ft/sec
Maximum Play Time : 74 min
Reading Speed : 3.9 to 4.6 ft/sec
Maximum Play Time : 20 min.
Reading Speed : 3.9 to 4.6 ft/sec.
Maximum Play Time : 74 min (Video + Audio)
1 channel : 1.0 Vp-p (75 Ω load)
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
Luminance Signal : 1.0 Vp-p (75 Ω load)
Color Signal : 0.286 Vp-p (75 Ω load)
• Samsung Electronics Co., Ltd reserves the right to change the specifications without
notice.
• Weight and dimensions are approximate.
37
READ THIS NOTICE BEFORE YOU OR YOUR CHILD USE ANY VIDEO GAME
A very small portion of the population have a condition which may cause them to
experience epileptic seizures or have momentary loss of consciousness when viewing
certain kinds of flashing lights or patterns that are commonly present in our daily
environment. These persons may experience seizures while watching some kinds of
television pictures or playing certain video games. Players who have not had any
previous seizures may nonetheless have an undetected epileptic condition.
If you or anyone in your family has experienced symptoms linked to an epileptic
condition (e.g. a seizure or loss of awareness), immediately consult your physician
before using any video games.
We recommend that parents observe their children while they play video games.
If you or your child experience any of the following symptoms: dizziness, altered vision,
eye or muscle twitching, involuntary movements, loss of awareness, disorientation,
or convulsions, DISCONTINUE USE IMMEDIATELY and consult your physician.
Please guide your children so that they do not eat the rubber-quality cover of the Game port.
FOLLOW THESE PRECAUTIONS WHENEVER USING VIDEO GAMES:
- When using your NUON Interactive DVD player, do not sit or stand too close to the
television screen. Play as far back from the screen as possible.
- Play video games on the smallest available television screen.
- Do not play if you are tired or need sleep.
- Always play in a well lit room.
- Be sure to take a 10 to 15 minute break every hour while playing.
Repetitive Strain Warning
Some people may experience fatigue or discomfort after playing for a long time.
Regardless of how you feel, you should ALWAYS take a 10 to 15 minute break every
hour while playing. If your hands or arms become tired or uncomfortable while playing,
stop and rest. If you continue to experience soreness or discomfort during or after play,
listen to the signals your body is giving you. Stop playing and consult a doctor. Failure
to do so could result in long term injury.
If your hands, wrist or arms have been injured or strained in other activities,
use of your system could aggravate the condition. Before playing, consult a doctor.
Motion Sickness
Samsung Extiva DVD players generate realistic images and 3-D simulations.
While playing or watching certain video images, some people may experience
dizziness, motion sickness or nausea. If you or your child experience any of these
symptoms, discontinue use and play again later.
Projection Television Warning
DO NOT USE WITH A FRONT OR REAR PROJECTION TV
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS
AMERICA, INC. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials
and workmanship for the following limited warranty period:
One (1) Year Parts and Labor
This limited warranty begins on the original date of purchase, and is valid only on products
purchased and used in the United States, and does not include transportation, installation,
removal or reinstallation. Warranty repairs must be performed by SAMSUNG’s authorized
service center. To receive warranty service, the original dated bill of sale must be presented
upon request as proof of purchase to SAMSUNG or SAMSUNG’s authorized service center.
Transportation to and from the service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge with new or
reconditioned parts, if found to be defective during the limited warranty period specified
above. The product must be returned during the warranty period with transportation charges
prepaid to SAMSUNG’s designated service center. Prior to returning any product for warranty service, the purchaser must contact SAMSUNG for problem determination and service
procedures. SAMSUNG does not warrant uninterrupted or error-free operation of the product. All replaced parts and products become the property of SAMSUNG and must be
returned to SAMSUNG. Replacement parts and products assume the remaining original
warranty, or ninety (90) days, whichever is longer.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, noncommercial use of this product and shall not apply to the following,
including, but not limited to: damage which occurs in shipment; applications and uses for
which this product was not intended; failures or problems which are caused by products or
equipment not supplied by SAMSUNG; accidents, misuse, abuse, neglect, misapplication,
fire, water, lightning or other acts of nature; incorrect electrical line voltage, fluctuations or
surges; damage caused by improper or faulty installation; improper connection with any
peripheral; product alteration or modification; improper or unauthorized repair; cosmetic
damage or exterior finish; product with altered serial numbers; failure to follow operating
instructions, customer adjustments, maintenance and environmental instructions that are
covered and prescribed in the instruction book; use of non-SAMSUNG or unauthorized
parts, supplies, accessories or equipment which damage this product or result in service
problems; failures or problems due to incompatibility with other equipment.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND
DESCRIBED ABOVE, AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS
WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR
GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO
THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE
LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR
OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT,
REFERENCE
Do not use a front or rear projection television with your NUON Interactive DVD Player.
Your projection television screen may be permanently damaged if video games with
stationery scenes or patterns are played on your projection television. Similar damage
may occur if you place a video game on hold or pause. If you use your projection television
with NUON Interactive Software, neither VM Labs nor any of VM Labs' licensees will be
liable for any damage. This situation is not caused by a defect in the DVD player or NUON
games; other fixed or repetitive images may cause similar damage to a projection television.
Please contact your TV manufacturer for further information.
Warranty (for USA users only)
Warranty (for Canada users only)
REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN
IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR
SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN
THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE
ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES
ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE
USE, MISUSE OR INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG NOT
CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY
SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS
PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion
or limitation of incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
To obtain warranty service, please contact SAMSUNG at:
SAMSUNG ELECTRONICS AMERICA, INC. - CONSUMER ELECTRONICS CUSTOMER SERVICE
400 Valley Road, Suite 201, Mt Arlington, NJ 07856
1-800-SAMSUNG (1-800-726-7864)
www.samsungsupport.com
LIMITED WARRANTY TO ORIGINAL PURCHASER
Samsung Electronics Canada Inc.(SECA), warrants that this product is free from defective
material and workmanship.
SECA further warrants that if this product falls to operate properly within the specified warranty period and the failure is due to improper workmanship or defective materials, SECA will
repair or replace the product at its option.
All warranty repairs must be performed by a SECA Authorized Service Center. (The name
and address of the location nearest you can be obtained by calling toll free: 1- 800- SAMSUNG)
LABOR
PARTS
One year (Carry- in)
One year
On carry-in models, transportation to and from the service center is the customer’s responsibility.
The original dated sales receipt must be retained by the customer and is the only acceptable
proof of purchase. It must be presented to the authorized service center at the time service is
requested.
EXCLUSIONS (WHAT IS NOT COVERED)
This warranty does not cover damage due to accident, fire, flood and/ or other acts of God;
misuse, incorrect line voltage, improper installation, improper or unauthorized repairs, commercial use or damage that occurs in shipping. Exterior and interior finish, lamps, glass are
not covered under this warranty. Customer adjustments which are explained in the instruction
manual are not covered under the terms of this warranty. This warranty will automatically be
voided for any unit found with a missing or altered serial number. This warranty is valid only
on products purchased and used in Canada.
REFERENCE
Memo
Memo
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement